Close Window

Assessment System Exam Viewer - ENetwork Final Exam - CCNA Exploration: Network Fundamentals (Version 4.0)

Below you will find the assessment items as presented on the exam as well as the scoring rules associated with the item. Cisco Networking Academy content is copyrighted and the unauthorized posting, distribution or sharing of this exam content is prohibited. 1 When must a router serial interface be configured with the clock rate command? when the interface is functioning as a DTE device when the interface timers have been cleared when the connected DTE device is shut down when the interface is functioning as a DCE device Observable 1 correctness of response Description 2 points for Option 4 0 points for any other option Max Value 2

Due to a security violation, the router passwords must be changed. What information can be learned from the following configuration entries? (Choose two.) Router(config)# line vty 0 3 Router(config-line)# password c13c0 Router(config-line)# login

The entries specify three Telnet lines for remote access. The entries specify four Telnet lines for remote access. The entries set the console and Telnet password to "c13c0". Telnet access will be denied because the Telnet configuration is incomplete. Access will be permitted for Telnet using "c13c0" as the password. Observable 1 correctness of response Description Option 2 and Option 5 are correct. 1 point for each correct option. 0 points if more options are selected than required. Max Value 2

Refer to the exhibit. A network technician is trying to determine the correct IP address configuration for Host A. What is a valid configuration for Host A? IP address: 192.168.100.19; Subnet Mask: 255.255.255.248; Default Gateway: 192.16.1.2 IP address: 192.168.100.20; Subnet Mask: 255.255.255.240; Default Gateway: 192.168.100.17 IP address: 192.168.100.21; Subnet Mask: 255.255.255.248; Default Gateway: 192.168.100.18 IP address: 192.168.100.22; Subnet Mask: 255.255.255.240; Default Gateway: 10.1.1.5

IP address: 192.168.100.30; Subnet Mask: 255.255.255.240; Default Gateway: 192.168.1.1 IP address: 192.168.100.31; Subnet Mask: 255.255.255.240; Default Gateway: 192.168.100.18 Observable 1 correctness of response Description 2 points for Option 2 0 points for any other option Max Value 2

A PC can not connect to any remote websites, ping its default gateway, or ping a printer that is functioning properly on the local network segment. Which action will verify that the TCP/IP stack is functioning correctly on this PC? Use the ipconfig /all command at the hosts command prompt. Use the ping 127.0.0.1 command at the command prompt. Use the traceroute command at the command prompt to identify any failures on the path to the gateway. Use FTP to check for connectivity to remote sites. Download a troubleshooting tool from the PC manufacturer's website. Observable Description 2 points for Option 2 0 points for any other option Max Value 2

correctness of response

Refer to the exhibit. When computer A sends a frame to computer D, what computers receive the frame? only computer D only computer A and computer D only computer B, computer C, and computer D all computers Observable 1 correctness of response Description 2 points for Option 1 0 points for any other option Max Value 2

A technician is asked to secure the privileged EXEC mode of a switch by requiring a password. Which type of password would require this login and be considered the most secure? console enable enable secret VTY Observable Description 2 points for Option 3 0 points for any other option Max Value 2

correctness of response

Which OSI layer does IP rely on to determine whether packets have been lost and to request retransmission? application presentation session transport Observable Description 2 points for Option 4 0 points for any other option Max Value 2

correctness of response

Refer to the exhibit. A network administrator remotely accesses the CLI of RouterB from PC1 using Telnet. Which statement is true about this connection? The data is automatically encrypted. A Telnet server process is running on PC1. The connection is made through a VTY session on the router. A GET request was sent to RouterB to retrieve data during this session. Observable 1 correctness of response Description 2 points for Option 3 0 points for any other option Max Value 2

Which three IPv4 addresses represent valid host addresses for a subnet? (Choose three.) 10.1.12.79/28 10.1.12.113/28 10.1.12.32/28 10.1.11.5/27 10.1.11.97/27

10.1.11.128/27 Observable 1 correctness of response Description Option 2, Option 4, and Option 5 are correct. 1 point for each correct option. 0 points if more options are selected than required. Max Value 3

10

What is the effect of using the Router# copy running-config startup-config command on a router? The contents of ROM will change. The contents of RAM will change. The contents of NVRAM will change. The contents of flash will change. Observable Description 2 points for Option 3 0 points for any other option Max Value 2

correctness of response

11

Refer to the exhibit. A PC is communicating with another PC on a remote network. The two networks are connected by three routers. Which action will help to identify the path between the hosts? Use the ipconfig command at the host. Use the ipconfig/all command at the destination. Use the tracert command at the host. Use the ping command at the destination. Observable 1 correctness of response Description 2 points for Option 3 0 points for any other option Max Value 2

12

Refer to the exhibit. A PC is connected to a network. Which action will verify that the PC can communicate with its default gateway? Use the ping 127.0.0.1 command. Use the ipconfig command. Use the ipconfig/all command. Use the ping 10.0.0.254 command. Observable 1 correctness of response Description 2 points for Option 4 0 points for any other option Max Value 2

13

Refer to the exhibit. Host C is able to ping 127.0.0.1 successfully, but is unable to communicate with hosts A and B in the organization. What is the likely cause of the problem? Hosts A and B are not on the same subnet as host C. The IP addresses on the router serial interfaces are wrong. The subnet mask on host C is improperly configured. The FastEthernet interface fa0/0 of router 1 is wrongly configured. Observable 1 correctness of response Description 2 points for Option 3 0 points for any other option Max Value 2

14

Refer to the exhibit. Host A and B are unable to communicate with each other. What is the reason for this? Host A is assigned a network address. Host B is assigned a multicast address. Host A and host B belong to different networks. The gateway addresses are network addresses. Observable 1 correctness of response Description 2 points for Option 4 0 points for any other option Max Value 2

15

Refer to the exhibit. Which list refers only to end devices? D,E,F,G A,H,B,C A,D,E,F A,D,E,G Observable 1 correctness of response Description 2 points for Option 1 0 points for any other option Max Value 2

16

Refer to the exhibit. PC1 is unable to access PC2. To troubleshoot this problem, the technician needs to confirm that the next hop interface is operational. Which default gateway address should the technician ping from PC1 to confirm this? 10.0.0.254 192.168.0.249 192.168.0.250 10.0.1.254 Observable 1 correctness of response Description 2 points for Option 1 0 points for any other option Max Value 2

17

Refer to the exhibit. While configuring a network, a technician wired each end of a Category 5e cable as shown. Which two statements are true about this setup? (Choose two.) The cable is suitable for connecting a switch to a router Ethernet port. The cable is suitable for connecting dissimilar types of devices. The cable is unusable and must be rewired. The cable is terminated in a way that the transmit pin is wired to the receive pin. The cable simulates a point-to-point WAN link. Observable 1 correctness of response Description Option 1 and Option 2 are correct. 1 point for each correct option. 0 points if more options are selected than required. Max Value 2

18

Refer to the exhibit. The serial interface of the router was configured with the use of the commands that are shown. The router cannot ping the router that is directly connected to interface serial 0/0/0. What should the network technician do to solve this problem? Configure the description at interface serial 0/0/0.

Configure an IP address on interface serial 0/0/0. Remove the no shutdown command at interface serial 0/0/0 Reboot the router. Observable 1 correctness of response Description 2 points for Option 2 0 points for any other option Max Value 2

19

Which subnet mask will allow 2040 hosts per subnet on the IP network 10.0.0.0? 255.255.0.0 255.255.254.0 255.255.252.0 255.255.248.0 255.255.240.0 255.255.255.128 Observable Description 2 points for Option 4 0 points for any other option Max Value 2

correctness of response

20

Refer to the exhibit. The nslookup command that is shown was issued on a Windows PC host. What does the 10.32.5.74 address represent? the IP address of the host the default gateway for the host the primary DNS server for the host the home page address for the host Observable 1 correctness of response Description 2 points for Option 3 0 points for any other option Max Value 2

21

Refer to the exhibit. What three statements are true about the IP configuration that is shown? (Choose three.) The prefix of the subnet mask is /26. The network on which this computer resides can have 30 hosts.

The computer is unable to communicate outside of the local network. The address that is assigned to the computer represents private addressing. The IP address that is assigned to the computer is routable on the Internet. The IP address that is assigned as the default gateway is valid for this host. Observable 1 correctness of response Description Option 2, Option 3, and Option 4 are correct. 1 point for each correct option. 0 points if more options are selected than required. Max Value 3

22

Which two actions could be taken by a router if a specific match is not made to a route in the routing table? (Choose two.) The packet will be discarded. The packet will be sent back to the source. The packet will be flooded out all interfaces. Neighboring routers are polled to find the best path. The packet will be forwarded to a default route if one is present. Observable Description Option 1 and Option 5 are correct. 1 point for each correct option. 0 points if more options are selected than required. Max Value 2

correctness of response

23

Refer to the exhibit. Which layered network model is shown in the diagram? Cisco IETF OSI TCP/IP Observable 1 correctness of response Description 2 points for Option 4 0 points for any other option Max Value 2

24

Which OSI layer addressing is required to route packets between two networks?

Layer 1 Layer 2 Layer 3 Layer 4 Observable 1 correctness of response Description 2 points for Option 3 0 points for any other option Max Value 2

25

What type of network is maintained if a server takes no dedicated role in the network? mainframe client/server peer-to-peer centralized Observable Description 2 points for Option 3 0 points for any other option Max Value 2

correctness of response

26

A routing issue has occurred in your internetwork. Which of the following type of devices should be examined to isolate this error? access point host hub router

switch Observable 1 correctness of response Description 2 points for Option 4 0 points for any other option Max Value 2

27

Which statement is true about Layer 3 addresses? They are physical addresses. They are used in routing decisions. They are only used on local networks. They are altered each time a packet crosses a router. Observable Description 2 points for Option 2 0 points for any other option Max Value 2

correctness of response

28

Which physical component is used to access and perform the initial configuration on a new unconfigured router?

Observable 1 correctness of response

Description 2 points for Option 2 0 points for any other option

Max Value 2

29

Which option shows how a router will route packets to a remote network?

Observable 1 correctness of response 2 points for Option 4

Description

Max Value 2

0 points for any other option

30

What is the Cisco IOS? system software for Cisco devices Read Only Memory in Cisco devices non-volatile storage for device configurations an initial operating system that is used for boot functions Observable Description 2 points for Option 1 0 points for any other option Max Value 2

correctness of response

31

Refer to the exhibit. Host A is configured with the correct IP address for the default gateway of the router R1 FastEthernet0/1 interface. How will a packet that is sent from host A to host B be handled by the devices on the network? R1 will drop the packet because R1 does not have a specific route in its routing table to the 10.1.1.0/24 network. R1 will forward the packet to its default gateway, the next hop router R2. R2 will forward the packet to the directly connected network 10.1.1.0/24. R1 will forward the packet to its default gateway, the next hop router R2. R2 will drop the packet because it does not have a default route to network 10.1.1.0/24. R1 will forward the packet to its default gateway, the next hop router R2. R2 will drop the packet because it does not have a route that is learned by a routing protocol to network 10.1.1.0/24. Observable 1 correctness of response Description 2 points for Option 2 0 points for any other option Max Value 2

32

What can the user do from the command prompt, Router(config-line)# ? Configure one of the network interfaces. Configure one of the physical or virtual lines.

Verify the running configuration on the device. Configure the parameters for one of the routing protocols. Observable 1 correctness of response Description 2 points for Option 2 0 points for any other option Max Value 2

33

Which table accurately associates the RFC 1918 private IP addresses with the correct network mask?

Observable 1 correctness of response

Description 2 points for Option 3 0 points for any other option

Max Value 2

34

Refer to the exhibit. A network technician has made several changes to R1 since the configuration has last been saved. The modified configuration did not produce the desired changes. The technician wants to store a backup copy of the saved configuration on a TFTP server before reloading. Which action will cause the unmodified data to be saved on the TFTP server?

Observable 1 correctness of response

Description 2 points for Option 2 0 points for any other option

Max Value 2

35

What happens when a host station receives a frame that contains its own MAC address in the destination field? The Layer 2 information is removed and the frame is pushed up to Layer 3.

The host station will copy the information to its buffers and send it back out. The frame originated from the host and will be ignored. The Layer 3 information is added to the frame. Observable 1 correctness of response Description 2 points for Option 1 0 points for any other option Max Value 2

36

What information can be gathered by using the command netstat? the default gateway the routing protocol active TCP connections the locally configured subnet mask Observable Description 2 points for Option 3 0 points for any other option Max Value 2

correctness of response

37

Which option represents a point-to-point logical topology diagram?

Observable 1 correctness of response

Description 2 points for Option 4 0 points for any other option

Max Value 2

38

How many host addresses may be assigned when using the 128.107.0.0 network address with a subnet mask of 255.255.248.0? 30 256 2046 2048 4094 4096 Observable Description 2 points for Option 3 0 points for any other option Max Value 2

correctness of response

39

Which three addresses are private IP addresses? (Choose three.) 10.0.0.1 46.1.1.88

172.31.31.10 172.32.16.10 192.168.8.8 Observable 1 correctness of response Description Option 1, Option 3, and Option 5 are correct. 1 point for each correct option. 0 points if more options are selected than required. Max Value 3

40

An administrator is in the middle of entering a lengthy command when suddenly output from the IOS appears stating that an interface has gone down and then up again. Consequently, the command that the administrator was typing is no longer legible on the terminal. What CLI keystrokes can be entered to return to the line that the administrator was typing? Ctrl-D Ctrl-K Ctrl-R Ctrl-Z Observable Description 2 points for Option 3 0 points for any other option Max Value 2

correctness of response

41

Which TCP/IP model layer creates additional overhead on network resources due to acknowledgments, tracking, and retransmission of data? internet transport application network access

Observable 1 correctness of response

Description 2 points for Option 2 0 points for any other option

Max Value 2

42

What is the consequence of issuing the erase startup-config command in privileged EXEC mode on a Cisco router? Data stored in RAM will be removed. Data stored in NVRAM will be erased. Information in flash memory will be removed. Flags in the configuration register will be set to 0. Both the startup-config and the running-config will be erased. Observable Description 2 points for Option 2 0 points for any other option Max Value 2

correctness of response

43

Which service is used when the nslookup command is issued on a computer? FTP DNS DHCP Telnet Observable Description 2 points for Option 2 0 points for any other option Max Value 2

correctness of response

44

Refer to the exhibit. Which two layers of the OSI model describe the same functions as the transport and internet layers of the TCP/IP model? (Choose two.) application layer presentation layer session layer transport layer network layer data link layer physical layer

Observable 1 correctness of response

Description Option 4 and Option 5 are correct. 1 point for each correct option. 0 points if more options are selected than required.

Max Value 2

45

In a network design project, a network designer needs to select a device to provide collision free connections to 40 hosts on the LAN. Which device should be selected? hub router switch firewall Observable Description 2 points for Option 3 0 points for any other option Max Value 2

correctness of response

46

Which command or commands will require authentication to access the privileged exec mode? RTRA(config)# enable secret cisco RTRA(config)# service password encryption RTRA(config)# line con 0 RTRA(config-line)# login RTRA(config-line)# password cisco RTRA(config)# line vty 0 4 RTRA(config-line)# login RTRA(config-line)# password cisco Observable Description 2 points for Option 1 0 points for any other option Max Value 2

correctness of response

47

An administrator makes changes to the default configuration of a router and saves them to NVRAM. After testing, it is discovered that the configurations did not have the desired effect and must be removed. What steps must be taken to remove the changes and return the router to the default configuration? Reboot the router. Use no version of the commands that are issued. Issue the erase startup-config command, and then reboot the router. Issue the erase running-config command, and then reboot the router. Observable Description 2 points for Option 3 0 points for any other option Max Value 2

correctness of response

48

Refer to the exhibit. The network administrator remotely accesses the CLI of RouterB from PC1 using a secure connection. Which statement is true about this connection? The Telnet server process is running on PC1. Only the exchange of the Telnet username and password is encrypted. The GET request is sent to RouterA to retrieve data.

The SSH service is used to connect PC1 to RouterB. Observable 1 correctness of response Description 2 points for Option 4 0 points for any other option Max Value 2

49

Refer to the exhibit. An administrator on PC1 wants to view some HTML code from a web page housed on the web server. Which client application will allow this request to be started?

Observable 1 correctness of response

Description 2 points for Option 1 0 points for any other option

Max Value 2

50

Which router configuration mode will require user authentication if an administrator issues the enable secret command? user executive mode privileged executive mode global configuration mode service specific configuration mode Observable Description 2 points for Option 2 0 points for any other option Max Value 2

correctness of response

Showing 1 of 1

Prev Page:

Next

Close Window
All contents copyright 2001-2010 Cisco Systems, Inc. All rights reserved. Privacy Statement and Trademarks.