Scribd
Upload
109 views

Introduction Serial Device Server

Serial device server technology.

Uploaded by

Erica Beasley
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
109 views

Introduction Serial Device Server

Serial device server technology.

Uploaded by

Erica Beasley
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

8-12 www. moxa. com i nf o@mox a.

com
I
n
t
r
o
d
u
c
t
i
o
n

t
o

S
e
r
i
a
l

D
e
v
i
c
e

S
e
r
v
e
r
s
8
Serial-to-Ethernet Device Servers
S
e
r
i
a
l
-
t
o
-
E
t
h
e
r
n
e
t

D
e
v
i
c
e

S
e
r
v
e
r
s


>
NPort

Provides a Wide Choice of Operation Modes


Introduction to Serial Device Servers
Device servers are used to connect serial devices to Ethernet LANs,
and are able to transmit data both to and from the serial device.
Moxas NPort line of device servers are essentially pre-programmed
computers that have a real-time OS and built-in TCP/IP protocol suite
that allows you to access, manage, and configure remote facilities and
equipment from anywhere in the world over the Internet.
No Restrictions on Host Type or Operating System
Any host computer that supports the TCP/IP protocol can access the
NPorts serial ports, eliminating the need for special-purpose drivers.
In addition, you will not be held back by your PCs limited number of
serial bus slots.
Real COM/TTY Drivers for Existing Software
NPort device servers also come with Real COM/TTY drivers for
accessing devices through a virtual COM or TTY port.
Device server technology makes device networking easy
Socket Modes
TCP Server Mode
When the NPort is configured
for TCP Server Mode, each serial
port is assigned a unique IP:Port
combination on the TCP/IP network,
and the NPort waits passively
for a host computer to establish a
connection with the attached serial
device. TCP Server mode supports
up to 4 simultaneous connections,
allowing multiple hosts to collect
data from the same serial device at
the same time.
When the NPort is configured for
TCP Client mode and data is received
from the attached device the NPort
establishes a TCP connection between
the attached device a specified host
computer. After the data has been
transferred, the NPort automatically
closes the connection. TCP Client
mode supports up to 4 simultaneous
connections, allowing multiple hosts
to collect data from the same serial
device at the same time.
TCP Client Mode
UDP Mode
UDP mode supports up to 4 IP groups. In UDP mode, the
attached device can exchange data simultaneously with up to
4 network destinations, and at a higher speed than when using
TCP. This mode is ideal for message display applications.
Request a
connection
Proceed with
data transmission
TCP/P
Ethernet
TCP Client
RS-232
Device

Request a
connection
Proceed with
data transmission
TCP/P
Ethernet
TCP Server
RS-232
Device

Directly proceed with


data transmission
(no connection required)
TCP/P
Ethernet
RS-232
Device
8-13 i nf o@mox a. com www. moxa. com
8
I
n
t
r
o
d
u
c
t
i
o
n

t
o

S
e
r
i
a
l

D
e
v
i
c
e

S
e
r
v
e
r
s
Device Connectivity
S
e
r
i
a
l
-
t
o
-
E
t
h
e
r
n
e
t

D
e
v
i
c
e

S
e
r
v
e
r
s


>
Driver Modes
Other Modes
Mode Selection Flowchart
RFC2217 Mode
When configured for Real COM mode,
each serial port is assigned an IP:Port
combination that is mapped to a host
computers local COM or TTY port using
Moxas NPort drivers. Legacy applications
can access the attached serial device using
the hosts local COM or TTY port, without
the need to modify serial COM software to
account for network protocols.
When the NPort is configured for RFC2217 mode,
each serial port is assigned an IP:Port combination
that is mapped by RFC2217-compliant drivers to
a virtual COM port. The RFC2217 protocol defines
general COM port control options based on the
Telnet protocol. The NPort supports any third
party driver that is RFC2217-compliant.
Real COM Mode
Pair Connection Mode
When configured for Pair Connection mode, two NPort device servers can be used to transmit RS-232 signals over Ethernet, and in this
way overcome the 15-meter limitation imposed by the RS-232 standard. One NPort connects to the PCs COM port, and the other NPort
connects to the serial device. The two NPort device servers are either connected to each other with a cross-over Ethernet cable, or are each
connected to an Ethernet LAN or WAN. Both data and modem control signals can be exchanged between the PC and device over Ethernet, but
DCD signals are not supported.
Reverse Telnet Mode Ethernet Modem Mode
When configured for Ethernet
Modem mode, the serial port on
the NPort behaves as if it were
attached to a modem, except that
data is transmitted over a network
instead of over phone lines. Ethernet
Modem Mode enables network
access for legacy software that was
originally designed to transmit data
by modem.
When configured for Reverse Telnet mode, the
NPort device servers serial ports provide
a connection to a server, with connections
initiated by a host over Ethernet. This is similar
to TCP server mode, except that Reverse
Telnet mode also provides Telnet-style CR/LF
conversion. Reverse Telnet mode can be used
for remote console management, in which the
NPort is used to enable network access to
the serial console ports of different equipment,
such as routers, switches, and servers.
Using legacy
COM-based software?
Host requires more
COM ports?
Using MOXA's
drivers?
Real COM
Mode
RFC2217
Mode
Contact your
saleperson.
Reverse
Telnet
UDP Mode
Start
TCP Server
Mode
TCP Client
Mode
Pair
Connection
Modes
RFC2217
Mode or TCP
Server Mode
Need to extend
serial transmission
range?
Need to perform
console
management?
Host application is
server or client?
Need serial control
parameters?
Using socket
program?
Which protocol,
TCP or UDP?
YES YES
YES YES
YES YES
YES YES
YES YES
TCP TCP UDP UDP
NO NO
NO NO
NO NO
NO NO
NO NO
NO NO
YES YES
Client Client
Server Server
COM3=P : Port
Driver Mode
TCP/P
Ethernet
RS-232
Device
8-14 www. moxa. com i nf o@mox a. com
I
n
t
r
o
d
u
c
t
i
o
n

t
o

S
e
r
i
a
l

D
e
v
i
c
e

S
e
r
v
e
r
s
8
Serial-to-Ethernet Device Servers
S
e
r
i
a
l
-
t
o
-
E
t
h
e
r
n
e
t

D
e
v
i
c
e

S
e
r
v
e
r
s


>
NPort

Administrator Makes Installation Easy


Web Console Provides Exceptional Convenience
NPort Administrator is designed to make it easy to install and
configure NPort 5000 device servers over the network. Five groups
of functions are supported to allow off-line COM mapping, device
monitoring, and searching for NPort device severs over the network.
Both NPort Administrator and an IP Serial Library are bundled with
NPorts integrated software suite, giving you everything you need to
manage, monitor, and reconfigure your NPort from remote locations.
Conguration Features
Broadcast search over the LAN for NPort device servers
Select and congure the NPorts operation mode
Upgrade the NPorts rmware
Export and import the NPorts congurations
Monitor the NPorts status
Auto IP report
IP, netmask, gateway
Static IP, DHCP, BOOTP
DNS server
NPort 5000 device servers are easily configured over the network with the web console or Telnet console.
Operation mode
TCP alive check time
Inactivity time
Delimiter
Force transmit
Packet length
Allow driver control
Maximum connection
Baudrate
Data bits, stop bit, parity
Flow control
Communication interface
Network Settings
Operation Settings
Serial Settings

You might also like