All-In-One Wireless Security System V1.

3 Programming Guide
Model # MG-6060 / MG-6030

Table of Contents
Things You Should Know ..................................... 2
About This Programming Guide........................................... Conventions ......................................................................... Installer Code (Default: 0000 / 000000) ............................... Maintenance Code (Default: 1111 / 111111) ....................... Master Code (Default: 1234 / 123456)................................. Decimal and Hexadecimal Values ....................................... 2 2 2 2 2 2

Remote Control Button Programming ............... 10 System Settings ................................................... 11 Wireless Programmable Output (PGM) Settings 12 Appendix 1: PGM Event Table ............................ 12 Appendix 2: Specifications ................................. 15 Appendix 3: Connection Diagrams..................... 15
Power Connections ........................................................... Telephone Line Connections ............................................ PGM Connections ............................................................. Hardwire Zone Connections.............................................. Connecting the Radio Antenna (MG-6060 only) ............... Connecting to a UIP-256................................................... X10 Transmitter Connections (MG-6060 only).................. Connecting Magellan to WinLoad ..................................... Connecting a Paradox Memory Key (PMC-3) ................... Tabletop Mounting ............................................................ Mounting Magellan on the Wall......................................... 15 16 17 18 18 19 19 20 20 21 21

Entering Programming Mode ............................... 3

Single Digit Data Entry Method............................................ 3 Feature Select Programming Method .................................. 3

Installer Quick Keys .............................................. 3 Zone Programming................................................ 3 Wireless Transmitter Programming..................... 4 System Timers ....................................................... 4 On-board Programmable Outputs (PGMs) .......... 5 System Options ..................................................... 5 Communicator Settings ....................................... 8 Report Codes ......................................................... 9

Appendix 4: Ademco Contact ID Report Code List ................ 22 Appendix 5: Automatic Report Code List .......... 24

Things You Should Know

About This Programming Guide
This programming guide should be used in conjunction with the Magellan Reference & Installation Manual which can be downloaded from our website at www.paradox.ca. Use this guide to record the settings programmed for this console.

Conventions
This symbol designates a warning or important information. This symbol designates a suggestion or reminder. This symbol designates a reference to another section, manual or guide. This symbol designates a feature that can also be programmed in the Installer menu which can be accessed by pressing [menu] and then entering your [INSTALLER CODE]. The icon will then be followed by the path or buttons that have to be pressed in order to access the feature once in the Installer menu. For example:
[4] [6]

= Once in the Installer menu, press the [4] key and then press the [6] key to access the desired feature.

Refer to the Installer Menu Overview on the back cover for more information on accessing and using the Installer menu.

Installer Code (Default: 0000 / 000000)

The Installer code is used to enter programming mode (see Entering Programming Mode on page 3), which allows you to program all the features, options and commands of the Magellan console except user codes. The Installer code can be 4 or 6 digits in length (see section [090] option [1] on page 5) where each digit can be any value from 0 to 9. See section [181] on page 11 to change the default code.

Maintenance Code (Default: 1111 / 111111)

The Maintenance code is similar to the Installer code. It can be used to enter programming mode (see Entering Programming Mode on page 3), which allows you to program all the features, options and commands except for the Magellan consoles communication settings (sections [100] to [154]) as well as any user codes. The Maintenance code can be 4 or 6 digits in length (see section [090] option [1] on page 5) where each digit can be any value from 0 to 9. See section [182] on page 11 to change the default code.

Master Code (Default: 1234 / 123456)

With the System Master code a user can use any arming method and can program user codes. The System Master code can be 4 or 6 digits in length (see section [090] option [1] on page 5), where each digit can be any digit from 0 to 9. The System Master code cannot be changed by the Installer or Maintenance code, but it can be reset to default. See section [200] on page 11 to reset to default.

Decimal and Hexadecimal Values

Figure 1: Decimal and Hexadecimal Values Hexadecimal only values: [1] = A [2] = B [3] = C [4] = D [5] = E [6] = F

Decimal and Hexadecimal Values: Keys [0] to [9] = 0 to 9

Programming Guide

Entering Programming Mode

1. 2. 3. 4. 5.

Use the built-in keypad to access Magellans installer programming mode. To access programming mode: Press and hold the [0] key. Enter your [INSTALLER CODE] or [MAINTENANCE CODE]. Enter the 3-digit [SECTION] you wish to program. Enter the required [DATA]. Press the [*] key to clear data or to go back one step. Press the [#] key to save changes.

There are two methods that can be used to enter data when in programming mode: Single Digit Data Entry and Feature Select Programming methods.

Single Digit Data Entry Method

After entering programming mode, some sections will require that you enter decimal values from 000 to 255. Other sections will require that you enter hexadecimal values from 0 to F. The required data will be clearly indicated in this manual. When entering the final digit in a section, Magellan will automatically save and advance to the next section. Refer to Figure 1 on page 2 to see the keys and their equivalent decimal and/or hexadecimal value.

Feature Select Programming Method

After entering certain sections, eight options will be displayed where each option from [1] to [8] represents a specific feature. Press the key corresponding to the desired option and the option number will appear in the LCD screen. This means the option is ON. Press the key again to remove the digit from the LCD screen (a * appears), thereby, turning OFF the option. Press the [*] key to set all eight options to OFF. When the options are set, press the [#] key to save and advance to the next section.

Installer Quick Keys

Key [1] = Key [2] = Key [3] = Key [4] =

To access the Installer Quick keys, press and hold the [0] key from the Main keypad, enter the [INSTALLER CODE] and then press from the Center keypad:
Test Report: Send the Test Report report code programmed in section [155] (page 10) to the monitoring station. Cancel Communication: Cancels all communication with the WinLoad software or with the monitoring station until the next reportable event. Answer WinLoad Software: Will force the console to answer an incoming call from the monitoring station that is using the WinLoad software. Call WinLoad Software: Will dial the PC telephone number programmed in section [118] (page 8) in order to initiate communication with a computer using the WinLoad software. Key [5] = Installer Test Mode: The installer test mode will allow you to perform walk tests where the siren will squawk to indicate opened zones. Press the [5] key again to exit.

Zone Programming
Zone Definitions ( [4] [6] ) 000 = Zone Disabled (default) 008 = Delayed Fire Zone 001 = Entry Delay 1 009 = 24Hr. Burglary Zone 002 = Entry Delay 2 010 = 24Hr. Hold-up Zone 003 = Follow Zone 011 = 24Hr. Buzzer Zone 004 = Follow / Stay Zone 012 = 24Hr. Gas Zone 005 = Instant Zone 013 = 24Hr. Heat Zone 006 = Instant / Stay Zone 014 = 24Hr. Water Zone 007 = Instant Fire Zone 015 = 24Hr. Freeze Zone Zone Options [1] = Auto-zone Shutdown (default) [6] = Intellizone [2] = Bypassable Zone (default) [7] = Delay alarm transmission [3] = Future Use [8] = Force Zone (default) [4] OFF OFF ON ON [5] OFF ON OFF ON Zone Alarm Type Audible alarm (default) Pulsed alarm Silent alarm Report only Intellizone is not for use in UL installations. Force Arming is not permitted in UL installations.

Section [001] [002] [003] [004] [005] [006] [007] [008] Magellan

Description

Zone Definition

Zone Options

Section [009] [010] [011] [012] [013] [014] [015] [016]

Description

Zone Definition

Zone Options

Zone 1:__________ Zone 2:__________ Zone 3:__________ Zone 4:__________ Zone 5:__________ Zone 6:__________ Zone 7:__________ Zone 8:__________

____/____/____ 1 2 3 4 5 6 7 8 ____/____/____ 1 2 3 4 5 6 7 8 ____/____/____ 1 2 3 4 5 6 7 8 ____/____/____ 1 2 3 4 5 6 7 8 ____/____/____ 1 2 3 4 5 6 7 8 ____/____/____ 1 2 3 4 5 6 7 8 ____/____/____ 1 2 3 4 5 6 7 8 ____/____/____ 1 2 3 4 5 6 7 8

Zone 9:__________ Zone 10:_________ Zone 11_________ Zone 12:_________ Zone 13:_________ Zone 14:_________ Zone 15:_________ Zone 16:_________

____/____/____ 1 2 3 4 5 6 7 8 ____/____/____ 1 2 3 4 5 6 7 8 ____/____/____ 1 2 3 4 5 6 7 8 ____/____/____ 1 2 3 4 5 6 7 8 ____/____/____ 1 2 3 4 5 6 7 8 ____/____/____ 1 2 3 4 5 6 7 8 ____/____/____ 1 2 3 4 5 6 7 8 ____/____/____ 1 2 3 4 5 6 7 8 3

In the desired zones corresponding section, assign the transmitters serial number. In sections [058] and [059], assign the 6-digit serial number of the transmitter that you are using as a wireless doorbell. You can also use these sections to view transmitter signal strength.
Section Serial Number [021] [022] [023] [024] [025] [026] [027] [028] Section [029] [030] [031] [032] [033] [034] [035] [036] Serial Number

Wireless Transmitter Programming

Zone 1: ____/____/____/____/____/____ Zone 2: ____/____/____/____/____/____ Zone 3: ____/____/____/____/____/____ Zone 4: ____/____/____/____/____/____ Zone 5: ____/____/____/____/____/____ Zone 6: ____/____/____/____/____/____ Zone 7: ____/____/____/____/____/____ Zone 8: ____/____/____/____/____/____

Zone 9: ____/____/____/____/____/____ Zone 10: ____/____/____/____/____/____ Zone 11: ____/____/____/____/____/____ Zone 12: ____/____/____/____/____/____ Zone 13: ____/____/____/____/____/____ Zone 14: ____/____/____/____/____/____ Zone 15: ____/____/____/____/____/____ Zone 16: ____/____/____/____/____/____ Wireless Doorbell 1: ____/____/____/____/____/____ Wireless Doorbell 2: ____/____/____/____/____/____

[037] to [057] Future use [058] [059]

System Timers
Section Data (value from 000 to 255) [060] [061] [062] [063] [064] [065] [066] [067] [068] [069] [070] [071] [072] [073] [074] [075] [076] [077] [078] [079] [080] [081] [082] [083] [084] [085] Description Entry delay 1 ( Entry delay 2 ( Exit delay (
[4] [4] ) [4] [4] )

Defaults

____/____/____ seconds ____/____/____ seconds ____/____/____ seconds ____/____/____ minutes ____/____/____ x 15 minutes ____/____/____ seconds (minimum 10 seconds) ____/____/____ seconds ____/____/____ times ____/____/____ seconds ____/____/____ seconds ____/____/____ minutes ____/____/____ days ____/____/____ rings ____/____/____ seconds ____/____/____ seconds ____/____/____ seconds ____/____/____ seconds (maximum 130 seconds) ____/____/____ seconds ____/____/____ seconds ____/____/____ repetitions ____/____/____ days ____/____/____ (000 to 007*) ____/____/____ (000 to 007*) Future use ____/____:____/____ Hours ____/____:____/____ Hours

045 secs. 045 secs. 060 secs.

*

[4] [4] )

Bell cut-off time ( No movement time Intellizone delay

[4] [4] )

004 mins. Disabled 045 secs. Disabled 005 times Disabled Disabled 015 mins. Disabled 008 rings 032 secs. 030 secs. Disabled

Recent closing delay Auto-zone shutdown PGM1 timer PGM2 timer Power failure report delay Auto-test report Number of rings TLM fail timer Answering machine override delay Delay alarm transmission Delay between dialing attempts Pager/voice delay Remote panic disarm lock delay Voice reporting message repetitions Closing delinquency delay Entry delay audio selection ( Exit delay audio selection ( Future use Auto-test report time Auto-arm time (
[8] [3] ) [4] [4] ) [4] [4] )

020 secs. 005 secs. 020 secs. 003 reps. Disabled 003 002 Future use Disabled Disabled

* 000 = No tone; 001 = Beeping; 002 = Countdown; 003 = Tonality 1; 004 = Tonality 2; 005 = Tonality 3; 006 = Tonality 4; 007 = Radio tuner (MG-6060 only)
For UL installations, the Entry delay must not exceed 45 seconds. For UL installations, the Exit delay must not exceed 60 seconds. * For UL installations, the Bell cut-off time must be a minimum of 4 minutes; for cUL installations, the Bell cut-off time must be a minimum of 5 minutes. For UL installations, the number of dialing attempts shall not exceed 10. Programming Guide

On-board Programmable Outputs (PGMs)

Section Description [086] [087] [088] [089] Event Group # (____/____) (____/____) (____/____) (____/____) Sub-group # (____/____) (____/____) (____/____) (____/____) Default No event programmed No event programmed No event programmed No event programmed

PGM1 Activation Event PGM1 Deactivation Event PGM2 Activation Event PGM2 Deactivation Event

Refer to Appendix 1: PGM Event Table on page 13 for the PGM events that can be used to program Magellans PGM outputs.

System Options
[090] General Options Option [1] [2] [3] [4] [5] [6] [7] [8] [091] Access code length Audible trouble warning (except AC power failures) Lock master code Use user code 16 as duress code Console tamper supervision Need code to bypass zones PGM1 normal state PGM2 normal state OFF 6 digits Disabled Disabled Disabled Disabled Disabled N.O. N.O. ON 4 digits Enabled Enabled Enabled Enabled Enabled N.C. N.C. Bold = Default setting OFF Panic 1 (Emergency) Panic 2 (Auxiliary) Panic 3 (Fire) Panic 1: Silent or audible alarm Panic 2: Silent or audible alarm Panic 3: Silent or audible alarm PGM1 used as (MG-6060 only) PGM2 used as (MG-6060 only) Disabled Disabled Disabled Silent Silent Silent Direct output Direct output ON Enabled Enabled Enabled Audible Audible Audible X10 output 7 X10 output 8 Bold = Default setting OFF Auto-arm on time (
[8] [2] )

Bold = Default setting

General Options Option [1] [2] [3] [4] [5] [6] [7] [8]

[092]

Arming/Disarming Options Option [1] [2] [3] [4] [5] [6] [7] [8] Auto-arm on no movement Auto-arm in what arming mode Switch to Stay arming if no entry delay is opened Regular arming switches to Force arming Stay arming switches to Force arming One-touch Regular/Force arming One-touch Stay arming ON Disabled Disabled Regular Disabled Disabled Disabled Disabled Disabled

Enabled Enabled Stay Enabled Enabled Enabled Enabled Enabled

Force arming and Auto-arming are not for use in UL installations. [093] Arming/Disarming Options Option [1] [2] [3] [4] [5] [6] [7] [8] Future use Future use Bell squawk when arming/disarming with remote control * No exit delay when arming with remote control Report system disarming Exit delay termination Follow zones become Entry Delay 2 zones when Delay zone is bypassed FM tuner ON when system is armed (
[8] [1] )

Bold = Default setting OFF Future use Future use Disabled Disabled Always Disabled Disabled Disabled ON Future use Future use Enabled Enabled After alarm only Enabled Enabled Enabled

(MG-6060 only)

* Bell Squawk on Arm must be enabled for UL installations.

Magellan

[094]

Zone Options Option [1] [2] [3] & [4] Stay delay zones Report zone restore Tamper recognition options
[3] OFF OFF ON ON [4] OFF ON OFF ON - Disabled - Trouble only - Disarmed: Trouble only - Armed: Follow zones alarm type (page 3) - Disarmed: Audible alarm - Armed: Follow zones alarm type (page 3)

Bold = Default setting OFF Disabled On Bell cut-off See table See table ON Enabled On zone closure See table See table

[5] [6] & [7]

Generate tamper trouble if detected on bypassed zone Wireless transmitter supervision options
[6] OFF OFF ON ON [7] OFF ON OFF ON - Disabled * - Trouble only - Disarmed: Trouble only - Armed: Follow zones alarm type (page 3) - Disarmed: Audible alarm - Armed: Follow zones alarm type (page 3)

No See table See table

Yes See table See table

[8]

Generate supervision trouble if detected on bypassed zone

No

Yes

For UL installations, Tamper recognition options must be enabled. For UL installations, Wireless supervision options must be enabled. * For UL installations, if the zone is programmed as a wireless fire zone, supervision must be enabled and the check-in supervision time must be set at 80 minutes (section [096] option [7] on page 6). [095] Zone Options Option [1] [2] [3] [4] [5] [6] to [8] Zone 15 is hardwire zone 1 * Zone 16 is hardwire zone 2 * EOL (End-Of-Line) resistors Stay arm siren delay Boat/car mode Future use OFF Disabled Disabled No EOL Disabled Disabled Future use ON Enabled Enabled Use EOL resistors Enabled Enabled Future use Bold = Default setting

* For UL installations, if either or both of the hardwired zones are enabled, then section [095] option [3] option must be enabled. This feature only applies to Magellans onboard zone inputs. Section [095] options [1] and [2] must be ON in order to use this feature. [096] General Options Bold = Default setting OFF Doorbell 1 tone options
[1] OFF OFF ON ON [2] OFF ON OFF ON - Tone 1 - Tone 2 - Tone 3 - Tone 4

Option
[1] & [2]

ON See table See table

See table See table

[3] & [4]

Doorbell 2 tone options

[3] OFF OFF ON ON [4] OFF ON OFF ON - Tone 1 - Tone 2 - Tone 3 - Tone 4

See table See table

See table See table

[5] [6] [7] [8]

Daylight savings time AC power failure warning * Check-in supervision time RF Interferences detection *

Disabled Disabled 24Hrs Disabled

Enabled Enabled 80 minutes Enabled

* This option must be enabled for UL installations. [097] Reserved for future use

Programming Guide

[098]

Dialer Options Option [1] & [2] Telephone line monitoring options *
[1] OFF OFF ON ON [2] OFF ON OFF ON - TLM disabled - Generate a trouble - Generate audible alarm if armed - Silent alarms become audible

Bold = Default setting OFF See table See table ON See table See table

[3] [4] [5] [6] [7] [8]

Switch to pulse on 5th attempt Call back Alternate dialing Force dial DTMF dialing Pulse ratio

Disabled Disabled Disabled Disabled Disabled 1:2

Enabled Enabled Enabled Enabled Enabled 1:1.5

* For UL installations, the telephone line monitoring must be enabled if off-premise transmission is used.
[099] Dialer Options 2 * Option [1] [2] to [8] Use monitoring station telephone number 2 as Future use OFF Regular Future use ON Backup Future use Bold = Default setting

* For UL installations, only one telephone number is allowed. [100] Event Call Direction Options for: Arming / Disarming Report Codes Option [1] [2] [3] [4] Call monitoring station telephone number 1 Call monitoring station telephone number 2 Call Pager telephone number Future use OFF Disabled Disabled Disabled Future use ON Enabled Enabled Enabled Future use Bold = Default setting

Alarm / Alarm Restore Report Codes [5] [6] [7] [8] [101] Call monitoring station telephone number 1 Call monitoring station telephone number 2 Call Pager telephone number Future use Disabled Disabled Disabled Future use Enabled Enabled Enabled Future use Bold = Default setting OFF Call monitoring station telephone number 1 Call monitoring station telephone number 2 Call Pager telephone number Future use Disabled Disabled Disabled Future use ON Enabled Enabled Enabled Future use

Event Call Direction Options for: Tamper / Tamper Restore Report Codes Option [1] [2] [3] [4]

Trouble / Trouble Restore Report Codes [5] [6] [7] [8] [102] Call monitoring station telephone number 1 Call monitoring station telephone number 2 Call Pager telephone number Future use Disabled Disabled Disabled Future use Enabled Enabled Enabled Future use Bold = Default setting OFF Call monitoring station telephone number 1 Call monitoring station telephone number 2 Call Pager telephone number Future use Disabled Disabled Disabled Future use ON Enabled Enabled Enabled Future use

Event Call Direction Options for Special Report Codes * Option [1] [2] [3] [4] to [8]

* For UL installations, only one telephone number is allowed.

Magellan

[103]

Wireless Transmitter Supervision Zone Options * Option [1] [2] [3] [4] [5] [6] [7] [8] Zone 1 supervision Zone 2 supervision Zone 3 supervision Zone 4 supervision Zone 5 supervision Zone 6 supervision Zone 7 supervision Zone 8 supervision OFF Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled ON

Bold = Default setting Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Bold = Default setting OFF ON Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled

[104]

Wireless Transmitter Supervision Zone Options * Option [1] [2] [3] [4] [5] [6] [7] [8] Zone 9 supervision Zone 10 supervision Zone 11 supervision Zone 12 supervision Zone 13 supervision Zone 14 supervision Zone 15 supervision Zone 16 supervision

* For UL installations, all programmed wireless zones must be supervised. For any wireless Fire zones in UL installations, the supervision option must be enabled (section [094] options [6] & [7]) and the check-in supervision time must be set at 80 minutes (section [096] option [7]).

Communicator Settings
Section Data [105] [106] Description Report format for monitoring station telephone number 1 ( Report format for monitoring station telephone number 2 (
001 = Ademco slow (1400Hz 10BPS) 004 = Ademco Contact ID (default)
[4] [3] ) [4] [3] )

____/____/____ ____/____/____

002 = Silent Knight (1400Hz 20BPS) 005 = SIA FSK

003 = SESCOA (2300Hz 20BPS) 006 = ADEMCO Express (DTMF 4+2)

[107] [108] [109] [110] [111]

____/____/____/____ ____/____/____/____ ____/____/____/____

Account number (

[4] [3] )

[4] [8] ) [4] [8] )

Panel identifier (for use with WinLoad software) ( Panel password (for use with WinLoad software) ( Reserved for future use

Monitoring station telephone number 1 (32 digits maximum; if less than 32, press [ok] to accept) (

[4] [3] )

___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___ [112] Monitoring station telephone number 2 (32 digits maximum; if less than 32, press [ok] to accept) (
[4] [3] )

___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___ [113] Pager Telephone # (32 digits maximum; if less than 32, press [ok] to accept) (
[4] [3] )

___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___
[114] Numeric message sent with Pager Reporting (32 digits maximum; if less than 32, press [ok] to accept) (
[4] [3] )

___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___
[118] PC telephone number for WinLoad (32 digits maximum; if less than 32, press [ok] to accept) ___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___ [119] Service telephone number* (32 digits maximum; if less than 32, press [ok] to accept) (
[4] [3] )

(MG-6060 only)

___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___
* Using Magellans speakerphone feature (MG-6060 only), the Service telephone number allows the user to directly call the installer or maintenance staff if any problems arise. If you are using any report format other than SIA in sections [105] and [106] and you would like to transmit an A, press [0] on the main keypad; if you would like to enter a space (non-reportable digit), press the [1] key on the center keypad.

Programming Guide

Table 1: Special Keys for Telephone Numbers

Keys to press [*] [#] Center [ACTION] (pause) key Action or Value * # Add a 4-second pause to the telephone number. Press the key and a P will be inserted into the telephone number

Report Codes
Arming Report Codes Section Data [120] ____/____ User Code 1 ____/____ User Code 2 ____/____ User Code 3 ____/____ User Code 4 [121] ____/____ User Code 5 ____/____ User Code 6 ____/____ User Code 7 ____/____ User Code 8 [122] ____/____ User Code 9 ____/____ User Code 10 ____/____ User Code 11 ____/____ User Code 12 [123] ____/____ User Code 13 ____/____ User Code 14 ____/____ User Code 15 ____/____ User Code 16 [129] [125] Special Arming Report Codes Section Data [124] ____/____ Auto-arming ____/____ Late to close ____/____ No movement ____/____ Partial arming ____/____ Quick-arming ____/____ Arming via PC ____/____ Future use ____/____ Future use [128] [127] Disarming Report Codes Section Data [126] ____/____ User Code 1 ____/____ User Code 2 ____/____ User Code 3 ____/____ User Code 4 ____/____ User Code 5 ____/____ User Code 6 ____/____ User Code 7 ____/____ User Code 8 ____/____ User Code 9 ____/____ User Code 10 ____/____ User Code 11 ____/____ User Code 12 ____/____ User Code 13 ____/____ User Code 14 ____/____ User Code 15 ____/____ User Code 16 Default = FF Tamper Report Codes Section Data [141] ____/____ Zone 1 ____/____ Zone 2 ____/____ Zone 3 ____/____ Zone 4 [142] ____/____ Zone 5 ____/____ Zone 6 ____/____ Zone 7 ____/____ Zone 8 [143] ____/____ Zone 9 ____/____ Zone 10 ____/____ Zone 11 ____/____ Zone 12 [144] ____/____ Zone 13 ____/____ Zone 14 ____/____ Zone 15 ____/____ Zone 16 Default = FF Special Disarming Report Codes Section Data [130] ____/____ End auto-arm ____/____ Disarm via PC ____/____ Future use ____/____ Future use

Alarm Report Codes Section Data [131] ____/____ Zone 1 ____/____ Zone 2 ____/____ Zone 3 ____/____ Zone 4 [132] ____/____ Zone 5 ____/____ Zone 6 ____/____ Zone 7 ____/____ Zone 8 [133] ____/____ Zone 9 ____/____ Zone 10 ____/____ Zone 11 ____/____ Zone 12 [134] ____/____ Zone 13 ____/____ Zone 14 ____/____ Zone 15 ____/____ Zone 16

Alarm Restore Report Codes Section Data [135] ____/____ Zone 1 ____/____ Zone 2 ____/____ Zone 3 ____/____ Zone 4 [136] ____/____ Zone 5 ____/____ Zone 6 ____/____ Zone 7 ____/____ Zone 8 [137] ____/____ Zone 9 ____/____ Zone 10 ____/____ Zone 11 ____/____ Zone 12 [138] ____/____ Zone 13 ____/____ Zone 14 ____/____ Zone 15 ____/____ Zone 16

Special Alarm Report Codes Section Data [139] ____/____ Emer. panic ____/____ Aux. panic ____/____ Fire panic ____/____ Recent closing [140] ____/____ Zone shutdown ____/____ Duress ____/____ Paramedical ____/____ Future use

Magellan

Tamper Restore Report Codes Section Data [145] ____/____ Zone 1 ____/____ Zone 2 ____/____ Zone 3 ____/____ Zone 4

System Troubles Report Codes Section Data [149] ____/____ Future use ____/____ AC failure ____/____ Battery failure ____/____ Timer loss

System Troubles Restore Report Codes Section Data [152] ____/____ TLM ____/____ AC failure ____/____ Battery failure ____/____ Timer prog.

Default = FF Special Report Codes Section Data [155] ____/____ Cold start ____/____ Test report ____/____ Future use ____/____ WinLoad logout [156] ____/____ Installer logon ____/____ Installer logout ____/____ Delinquency ____/____ Future use [157] to [160] Reserved for future use

[146]

____/____ Zone 5 ____/____ Zone 6 ____/____ Zone 7 ____/____ Zone 8

[150]

____/____ Unit tamper ____/____ Fail to comm. ____/____ TX low battery ____/____ TX superv. loss

[153]

____/____ Unit tamp. rest. ____/____ Future use ____/____ TX low battery ____/____ TX superv. rest.

[147]

____/____ Zone 9 ____/____ Zone 10 ____/____ Zone 11 ____/____ Zone 12

[151]

____/____ RF interference ____/____ PGM Supervision Loss ____/____ PGM Tamper ____/____ Future use

[154]

____/____ RF interference ____/____ PGM Supervision Restored ____/____ PGM Tamper Restored ____/____ Future use

[148]

____/____ Zone 13 ____/____ Zone 14 ____/____ Zone 15 ____/____ Zone 16

Remote Control Button Programming

Table 2: Remote Control Button Options
Hex 0 1 2 3 4 5 6 7 Regular arming Stay arming Instant arming Force arming Future use Future use Future use Description Button disabled Hex 8 9 A* B* C* D* E* F* Panic 1 Panic 2 Panic 3 PGM Activation (Event Group #07. See Appendix 1: PGM Event Table on page 13) PGM Activation (Event Group #08. See Appendix 1: PGM Event Table on page 13) Turn FM radio ON/OFF (MG-6060 only) FM radio memory scan (MG-6060 only) Non-medical alarm Description

* = Hex values A to F are keys [1] to [6] from Magellans Center Keypad. Refer to Figure 1 on page 2. = The panic feature (section [091] options [1] to [3]) must be enabled.

10

Programming Guide

Programming the MG-REM1

Section RC# Data (Default: 4DE0) [161] [162] [163] [164] [165] [166] [167] [168] 1 2 3 4 5 6 7 8 Section RC# Data (Default: 4DE0)

______ ______ ______ ______ ______ ______ ______ ______

______ ______ ______ ______ ______ ______ ______ ______

______ ______ ______ ______ ______ ______ ______ ______

______
+

[169] [170] [171] [172] [173] [174] [175] [176]

9 10 11 12 13 14 15 16

______ ______ ______ ______ ______ ______ ______ ______

______ ______ ______ ______ ______ ______ ______ ______

______ ______ ______ ______ ______ ______ ______ ______

______
+

______
+

______
+

______
+

______
+

______
+

______
+

______
+

______
+

MG-REM1

______
+

______
+

______
+

______
+

Please see the warning below Programming the MG-REM2.

______
+

______
+

Programming the MG-REM2

Section RC# Data (Default: 4DE0) [161] [162] [163] [164] [165] [166] [167] [168] 1 2 3 4 5 6 7 8 Section RC# Data (Default: 4DE0)

______ ______ ______ ______ ______ ______ ______ ______

______ ______ ______ ______ ______ ______ ______ ______

______ ______ ______ ______ ______ ______ ______ ______

______
+

[169] [170] [171] [172] [173] [174] [175] [176]

9 10 11 12 13 14 15 16

______ ______ ______ ______ ______ ______ ______ ______

______ ______ ______ ______ ______ ______ ______ ______

______ ______ ______ ______ ______ ______ ______ ______

______
+

______
+

______
+

______
+

______
+

______
+

______
+

______
+

______
+

______
+

______
+

MG-REM2

______
+

______
+

______
+

______
+

The

button of the MG-REM1 and MG-REM2 remote controls has been permanently programmed to disarm the system. However, when button can be used for volume control. The
,
+

the system is disarmed and the Magellan consoles radio is on (MG-6060 only), the buttons functionality cannot be altered. The function with the MG-REM1 remote control. The remote control. feedback from the system. The buttons functionality cannot be altered. The
+ +

button of the MG-REM2 remote control has been permanently programmed to request and
+

button combinations do not

and

button combinations do not function with the MG-REM2

System Settings
Section Data [180] [181] [182] [200] [201] Description Installer code lock (Enter 147 to lock code, 000 to unlock code) Installer code (
[4] [8] ) [4] [8] )

Default 000 000000 111111

____/____/____ ____/____/____/____/____/____ ____/____/____/____/____/____ Reset Master code to default (123456) Reset all programmable sections to factory default values

Maintenance code (

Magellan

11

Wireless Programmable Output (PGM) Settings

Section Description [210] [211] [212] [213] [214] [215] [216] [217] Event Group # (____/____) (____/____) (____/____) (____/____) (____/____) (____/____) (____/____) (____/____) Sub-group # (____/____) (____/____) (____/____) (____/____) (____/____) (____/____) (____/____) (____/____) Default No event programmed No event programmed No event programmed No event programmed No event programmed No event programmed No event programmed No event programmed

PGM1 Activation Event PGM1 Deactivation Event PGM2 Activation Event PGM2 Deactivation Event PGM3 Activation Event PGM3 Deactivation Event PGM4 Activation Event PGM4 Deactivation Event

Refer to Appendix 1: PGM Event Table on page 13 for the PGM events that can be used to program Magellans PGM outputs.
Section [218] Wireless PGM Supervision Options Option [1] [2] [3] [4] [5] to [8] Section [219] Wireless PGM Console Supervision Options (Follow Alarm/Follow Bell) Option [1] [2] [3] [4] [5] to [6] Section Data [240] [241] [242] [243] PGM1 console supervision PGM2 console supervision PGM3 console supervision PGM4 console supervision Future Use Description Default 000 000 000 000 OFF Disabled Disabled Disabled Disabled ON Enabled Enabled Enabled Enabled Bold = Default setting PGM1 supervision PGM2 supervision PGM3 supervision PGM4 supervision Future Use OFF Disabled Disabled Disabled Disabled ON Enabled Enabled Enabled Enabled Bold = Default setting

____/____/____ (000 to 008) ____/____/____ (000 to 008) ____/____/____ (000 to 008) ____/____/____ (000 to 008)

Wireless PGM1 timer Wireless PGM2 timer Wireless PGM3 timer Wireless PGM4 timer

000 = No delay; 001 = 1s delay; 002 = 5s delay; 003 = 15s delay; 004 = 30s delay; 005 = 1min delay; 006 = 5min delay; 007 = 15min delay; 008 = 30min delay.

12

Programming Guide

Appendix 1: PGM Event Table

Event Group # 00 = Zone closed 01 = Zone opened 02 = System status 01 to 16 = Zone number 99 = Any zone number 00 = N/A 01 = N/A 02 = Silent alarm 03 = Buzzer alarm 04 = Steady alarm 05 = Pulsed alarm 06 = Strobe 07 = Alarm stopped 08 = Squawk ON 09 = Squawk OFF 10 = Ground start 11 = System disarmed 12 = System armed 13 = Entry delay engaged 99 = Any system status event 00 = Bell OFF 01 = Bell ON 02 = Bell Squawk Arm 03 = Bell Squawk Disarm Future use 00 = Telephone line trouble 01 = Future use 02 = Arm with no entry delay 03 = Arm in Stay mode 04 = Arm in Force mode 05 = Full arm when armed in Stay mode 06 = PC fail to communicate 07 = Future use 08 = Future use 09 = Doorbell 1 battery trouble 10 = Doorbell 1 battery trouble restore 11 = Doorbell 2 battery trouble 12 = Doorbell 2 battery trouble restore 13 = Utility Key 1 pressed (keys [1] and [9] from the center keypad) 14 = Utility Key 2 pressed (keys [2] and [10] from the center keypad) 15 = Utility Key 3 pressed (keys [3] and [11] from the center keypad) 16 = Utility Key 4 pressed (keys [4] and [12] from the center keypad) 17 = Utility Key 5 pressed (keys [5] and [13] from the center keypad) 18 = Utility Key 6 pressed (keys [6] and [14] from the center keypad) 19 = Utility Key 7 pressed (keys [7] and [15] from the center keypad) 20 = Utility Key 8 pressed (keys [8] and [16] from the center keypad) 21 = User remote access granted (MG-6060 only) 22 = User remote access denied (MG-6060 only) 23 = Tamper generated alarm 24 = Supervision loss generated alarm 99 = Any non-reportable event 01 to 16 = User number 99 = Any user number 01 to 16 = Zone number 99 = Any zone number Future use 01 to 16 = Zone number 99 = Any zone number 01 to 16 = Zone number 99 = Any zone number 01 to 16 = User number 99 = Any user number Sub-group #

03 = Bell status

04 = Future use 05 = Non-reportable event

06 = Remote access 07 = PGM activation (Remote control button option B; see page 10) 08 = PGM activation (Remote control button option C; see page 10) 09 = Cold Start zone 10 = Future use 11 = Smoke Maintenance signal 12 = Delay zone alarm transmission 13 = Arming with user

Magellan

13

Event Group # 14 = Special arming 00 = Auto-arming 01 = Late to close 02 = No movement arming 03 = Partial arming 04 = Quick arming 05 = Arming through WinLoad 99 = Any special arming event 01 to 16 = User number 99 = Any user number

Sub-group #

15 = Disarming with user 16 = Disarm after alarm with user * 17 = Alarm cancelled with user ** 18 = Special disarming

00 = Auto-arm cancelled 01 = Disarm through WinLoad 02 = Disarm through WinLoad after alarm * 03 = Alarm cancelled through WinLoad ** 04 = Non-medical alarm cancelled 99 = Any special disarming event

19 = Zone bypassed 20 = Zone in alarm 21 = Fire alarm 22 = Zone alarm restore 23 = Fire alarm restore 24 = Special alarm 00 = Panic non-medical emergency 01 = Panic medical (this medical panic alarm is not UL approved) 02 = Panic fire 03 = Recent closing 04 = Global shutdown 05 = Duress alarm (User 16) 99 = Any special alarm event 01 to 16 = Zone number 99 = Any zone number 00 = N/A 01 = AC failure 02 = Battery failure 03 = Clock loss 04 = Console tamper 05 = Fail to communicate to monitoring station 06 = Fail to communicate to voice report 07 = Fail to communicate to pager 08 = RF interference 99 = Any new trouble event 00 = Telephone line restored 01 = AC failure 02 = Battery failure 03 = Clock lost 04 = Console tamper restore 05 = N/A 06 = N/A 07 = N/A 08 = RF interference restore 99 = Any trouble restore event 01 to 16 = Zone number 99 = Any zone number

25 = Zone shutdown 26 = Zone tampered 27 = Zone tamper restore 28 = New trouble

29 = Trouble restored

30 = Low battery on zone 31 = Low battery on zone restore 32 = Zone supervision trouble 33 = Zone supervision restored 01 to 16 = Zone number 99 = Any zone number

14

Programming Guide

Event Group # 34 = Special

Sub-group # 00 = System power up 01 = Reporting test 02 = WinLoad logon 03 = WinLoad logoff 04 = Installer in programming mode 05 = Installer exited programming mode 06 = Closing delinquency delay elapsed 99 = Any special event 01 to 16 = User number 99 = Any user number

35 = Non-medical alarm

* An armed system is or was in alarm and was disarmed by a user. ** A disarmed system is or was in alarm (e.g. 24Hr. zone) and was disarmed by a user. 36 = Zone triggered a utility report 37 = Signal strength weak 1 38 = Signal strength weak 2 39 = Signal strength weak 3 40 = Signal strength weak 4 41 = Reserved 42 = Reserved 43 = PGM supervision lost 44 = PGM supervision restored 45 = PGM tampered 46 = PGM tamper restored 47 = Future use 48 = Fire delay started 49 = Fire delay cancelled 50 = PGM cold start Reserved Reserved 01 to 04 = PGM number 99 = Any PGM number Future use 01 to 16 = Zone number 99 = Any zone number 01 to 04 = PGM number 99 = Any PGM number 01 to 16 = Zone number 99 = Any zone number

Appendix 2: Specifications
Input Voltage Backup Battery PGMs Standby Battery Life Temperature Range Approvals
* It is recommended that you use a 12Vac 1A transformer to power the Magellan console. The console will generate less heat when connected to a 12Vac transformer than when connected to a 16.5Vac transformer.

12Vac to 16Vac* 20VA or 12Vdc to 18Vdc 1A 7.2Vdc NiMH rechargeable battery pack (order # 0780100178) Two N.O. solid-state relays (not polarized); Internal resistance - 16 (max.); Max. handling current 100mA Minimum 24 hours 0C to 50C (32F to 122F)

Max. Current Consumption 1A

Magellan

15

Appendix 3: Connection Diagrams

Power Connections
Figure 2: Connecting the AC Transformer
Back view of the Magellan console. 12Vac to 16Vac 1A Do not use any switchcontrolled outlets.

Insert the transformers wires into the AC terminals.

Figure 3: Connecting the DC Power Supply

Back view of the Magellan console. Insert the transformers wires into the AC terminals. 12Vdc to 18Vdc 1A

DC Power Supply

Figure 4: Connecting the Battery

Backview of the Magellan console.

1. Insert the backup batterys plug into the

connector labelled BATT.

2. Slide in the battery pack horizontally, tilt the battery pack 3. Snap in the battery compartment
cover when finished.

downward and then tuck it in Magellans battery compartment.

To order a battery pack, the battery packs part number is: Paradox #0780100178.

16

Programming Guide

Telephone Line Connections

Figure 5: Telephone Line Direct Connect
Telephone Line Connection Note The Magellan console must be able to seize the telephone line and place a call in an emergency situation. It must be able to do this even if other equipment (telephones, answering machines, computer modems, etc.) already has the line in use. To do so, the Magellan console must be connected to a properly installed RJ31X (or RJ38X) jack that is electrically in series with and ahead of all other equipment attached to the same telephone line. Proper installation is depicted in the diagram below. If you have any questions concerning these instructions, you should consult your telephone company or a qualified installer about installing the RJ31X (or RJ38X) jack and the Magellan console for you.

Back view of the Magellan console. To connect the telephone line directly to the console: 1. Connect a RJ31X to the R-1, T1, RING and TIP terminals as shown at right. 2. Connect the telephone company wires and the home telephone to the RJ31X.

Figure 6: Line Plug Connection

Back view of the Magellan console.

Do not connect the RJ-11 cable into this plug.

To connect the telephone line directly to the console: 1. Insert one end of the 4-pin RJ-11 cable into the line plug of the Magellan console. 2. Insert the other end of the RJ-11 cable into a standard telephone wall plug.

PGM Connections
Figure 7: PGM Connections
Method 2
(> 100mA)

Devices such as a light, etc.

Back view of the Magellan console.

Do not exceed 24Vdc when connecting the PGM outputs.

Method 1 (< 100mA)

External relay External DC Power Supply

External DC Power Supply

Devices such as a light, etc.

If the PGM current consumption is less than 100mA, use method 1. If the PGM current consumption is to exceed 100mA, use method 2.

Magellan

17

Hardwire Zone Connections

Figure 8: Hardwire Zone Connections

Connecting the Radio Antenna (MG-6060 only)

Figure 9: Connecting the Radio Antenna
Back view of the Magellan console.

If the radio reception is not very good, connect the supplied radio antenna to the ANT terminal of the Magellan console. Move the antenna around until the spot with the best reception is found.

18

Programming Guide

Connecting to a UIP-256
Figure 10: Connecting to a UIP-256 Universal In-Field Programmer
Connect the 10pin cable of the UIP-256 to the 10pin connector of the Magellan console Back view of the Magellan console.

UIP-256 Universal In-Field Programmer

Standard DB-9 cable (9-pin serial cable)

Download latest firmware version of Magellan from the Paradox website at www.paradox.ca

X10 Transmitter Connections (MG-6060 only)

Figure 11: Connecting the X10 Transmitter
1. Connect one end of the inverted 4-pin RJ-11 cable into the X10 plug of the console. 2. Connect the other end of the inverted 4-pin RJ-11 cable into the X10 transmitter. 3. Plug the X10 transmitter into a standard wall outlet. For information on programming the X10 features of Magellan, refer to the X10 Operation User Guide which can be found and downloaded for free from our Web site at www.paradox.ca. X10 devices (transmitters, modules, etc.) are not supplied and cannot be purchased through Paradox Security Systems Ltd. Back view of the Magellan console.

Do not connect the X10 transmitter into this plug.

1 Inverted 4-pin RJ-11 cable

Make sure that an inverted 4-pin RJ-11 cable is used when connecting the Magellan console to the X10 transmitter. Note the pin configuration below: Magellan Console Pin 1 Pin 2 Pin 3 Pin 4 X10 Transmitter Pin 4 Pin 3 Pin 2 Pin 1 X10 transmitter 2

Inverted 4-pin RJ-11 cable

Magellan

19

Connecting Magellan to WinLoad

Figure 12: Connecting Magellan to WinLoad
4- to 10-pin cable (supplied with the 306 Adapter) Back view of the Magellan console.

306 Adapter Computer containing WinLoad software Standard DB-9 cable (9-pin serial cable)

4-pin connector cable

Connecting a Paradox Memory Key (PMC-3)

Figure 13: Connecting a Paradox Memory Key (PMC-3)
PMC-3

Back view of the Magellan console.

Jumper ON: Read from and/or write to memory key Jumper OFF: Write protected (Read from the memory key only)

Download Data to Destination Console

To download the data of a memory key into a console: 1. Remove power from the Magellan console (AC and battery) and connect the memory key to the 5-pin connector on the left side of the back of the console as shown above. 2. Re-apply both AC and battery power to the console. 3. Press the [OK] key and Magellan will begin downloading the data from the memory key.

The installer code of the Magellan console used to download data to the memory key must be the same installer code programmed in the Magellan console that is to download the contents from the same memory key. If the installer codes do not match, the contents of the memory key cannot be downloaded into the receiving console. Example: The contents of the Magellan console A will be copied into memory key B. The installer code for console A is 111111. In order to download the contents of memory key B into the Magellan console C, the installer code programmed in console C must also be 111111.

Copy Data to Memory Key from Source Console

To copy the contents of a console into the memory key. 1. Remove power from the Magellan console (AC and battery) and connect the memory key to the 5-pin connector on the left side of the back of the console as shown above. Re-apply both AC and battery power to the console. 2. Press the [NEXT] key and then the [OK] key. Magellan will begin copying its data into the memory key.

20

Programming Guide

Tabletop Mounting
Figure 14: Tabletop Mounting
Plastic feet (x2) Back view of the Magellan console. To mount the Magellan console on a tabletop the wall plate has to be inserted beforehand: 1. Slide the wall plates tabs labeled B into the Magellan consoles open slots labeled D (see Figure 15 on page 21). 2. Insert two screws (included) through the wall plates screw holes labeled C into holes labeled E in the Magellan console (see Figure 15 on page 21). 3. Insert the two plastic feet (included) into the appropriate holes on the back plate of the Magellan console as shown at left. 4. Attach the two rubber stops (included) to the lower edge of the wall plate as shown at left. The plastic feet are used to raise the Magellan console to a slight angle for easy viewing while the rubber stops prevent the console from sliding when Magellan is being used.

Wall plate

Rubber stops (x2)

Tabletop

Tabletop mounting may not be an approved installation method by local regulations. It is recommended that the local regulations be verified prior to installing the Magellan console using this method.

Mounting Magellan on the Wall

Figure 15: Mounting Magellan onto the Wall Plate
To mount the wall plate: 1. Place the wall plate on the desired spot of the wall. 2. Drill and insert the screws into the holes labeled A at left. To mount the Magellan console: 1. 2. 3. 4. B Inset 1: Magellans Backplate Place the console back plate flush against the mounted wall plate. Slide the Magellans open slots labeled D (see Inset 1 below) onto the wall plates tabs labeled B. Gently apply downward pressure to insert the wall plates tabs into Magellans open slots. Insert two screws through the wall plates screw holes labeled C and into Magellans back plate screw holes labeled E (see Inset 1 below). This will secure the console to the wall.

A (x7)

Magellan

21

Appendix 4: Ademco Contact ID Report Code List

CID# Reporting Code Programming Value CID# 151 01 02 03 152 153 154 155 04 05 06 07 08 09 0A 0B 0C 156 157 158 159 161 162 163 Reporting Code Gas detected Refrigeration Loss of heat Water leakage Foil break Day trouble Low bottled gas level High temperature Low temperature Loss of air flow Carbon monoxide detected Tank level Programming Value 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 CID# 327 Reporting Code Notification appliance chk. #4 Programming Value 4E Medical Alarms - 100 100 101 102 Medical alarm * Pendant transmitter Fail to report in

System Peripheral Troubles - 330 and 340 330 331 332 333 334 335 336 337 338 339 341 System peripheral Polling loop open Polling loop short Expansion module failure Repeater failure Local printer paper out Local printer failure Exp. module DC loss Exp. module low battery Exp. module reset Exp. module tamper Exp. module AC loss Exp. module self-test fail RF receiver jam detect 4F 50 51 52 53 54 55 56 57 58 59 5A 5B 5C

Fire Alarms - 110 110 111 112 113 114 115 116 117 118 Fire alarm Smoke Combustion Water flow Heat Pull station Duct Flame Near alarm

Fire Supervisory - 200 and 210 200 201 Fire supervisory Low water pressure Low CO2 Gate valve sensor Low water level Pump activated Pump failure 32 33 34 35 36 37 38

342 343 344

Panic Alarms - 120 120 121 122 123 124 125 Panic Alarm Duress Silent Audible Duress - Access grated Duress - Egress granted 12 0D 0E 0F 10

202 203 204 205 206

Communication Troubles - 350 and 360 350 351 352 353 Communication Telco 1 fault Telco 2 fault Long range radio Fail to communicate Loss of radio supervision Loss of central polling Long range radio VSWR prob. 5D 5E 5F 60 61 62 63 64

System Troubles - 300 and 310 300 System trouble AC loss Low system battery RAM checksum bad ROM checksum System reset Panel program changed Self-test failure System shutdown Battery test failure Ground fault Battery missing/dead 39 3A 3B 3C 3D 3E 3F 40 41 42 43 44

Burglar Alarms - 130 130 131 132 133 134 135 136 137 138 139 Burglary Perimeter Interior 24-hour Entry/Exit Day/Night Outdoor Tamper Near alarm Intrusion verified 13 14 15 16 17 18 19 1A 1B 1C

354 355 356 357

301 302 303 304 305 306 307 308 309 310 311

Protection Loop Troubles - 370 370 371 372 373 374 375 376 377 378 Protection loop Protection loop open Protection loop short Fire trouble Exit error alarm Panic zone trouble Hold-up zone trouble Swinger trouble Cross-zone trouble 65 66 67 68 69 6A 6B 6C 6D

General Alarms - 140 140 141 142 143 144 145 146 147 General alarm Polling loop open Polling loop short Expansion module failure Sensor tamper Expansion module tamper Silent burglary Sensor supervision failure 1D 1E 1F 20 21 22 23 24

312 313

Power supply over current limit 45 Engineer reset 46

Sounder/Relay Troubles - 320 320 321 322 323 324 325 Sounder/relay Bell 1 Bell 2 Alarm relay Trouble relay Reversing relay Notification appliance chk. #3 47 48 49 4A 4B 4C 4D

Sensor Troubles - 380 and 390 380 381 382 383 384 385 386 Sensor trouble Loss of supervision - RF Loss of supervision - RPM Sensor tamper RF transmitter low battery Smoke detector Hi sensitivity 6E 6F 70 71 72 73

24-hour Non-burglary - 150 and 160 150 24-hour non-burglary 25

326

Smoke detector Low sensitivity 74

22

Programming Guide

CID# 387 388 389 391 392 393

Reporting Code

Programming Value

CID# 451 452 453 454 455 456 457

Reporting Code Early open/close Late open/close Failed to open Failed to close Auto-arm failed Partial arm Exit error (user) User on premises Recent close

Programming Value 9A 9B 9C 9D 9E 9F A0 A1 A2

CID# 603 604 605 606 607 608 609 611 612 613

Reporting Code Periodic RF transmission Fire test Status report to follow Listen-in to follow Walk test mode Periodic test - system trouble present Video transmitter active Point test OK Point not tested Intrusion zone walk tested Fire zone walk tested Panic zone walk tested Service request Event log reset Event log 50% full Event log 90% full Event log overflow Time/Date reset Time/Date inaccurate Program mode entry Program mode exit 32-hour event log marker Schedule change Exception schedule change Access schedule change System inactivity

Programming Value BF C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7 D8

Intrusion detector Hi sensitivity 75 Intrusion detector Low sensitivity Sensor self-test failure Sensor watch trouble Drift compensation error Maintenance alert 76 77 78 79 7A

Open/Close - 400 400 401 402 403 404 405 406 407 408 409 Open/Close Open/Close by user Group open/close Automatic open/close Late to open/close Deferred open/close Cancel Remote arm/disarm Quick arm Keyswitch open/close 7B 7C 7D 7E 5E 5F 7F 80 81 82

458 459

System - 460 461 462 463 464 465 466 Wrong code entry Legal code entry Re-arm after alarm Auto-arm time extended Panic alarm reset Service ON/OFF premises A3 A4 A5 A6 A7 A8

614 615 616 621 622 623 624

Sounder Relay Disabled - 520 520 Sounder/Relay disabled Bell 1 disabled Bell 2 disabled Alarm relay disabled Trouble relay disabled Reversing relay disabled Notification appliance chk. #3 disabled Notification appliance chk. #4 disabled A9 AA AB AC AD AE AF B0

Remote Access - 410 411 412 413 414 415 416 Call back request made Success - download access Unsuccessful access System shutdown Dialer shutdown Successful upload 83 84 85 86 87 88

625 626 627 628 629 630 631 632 654

521 522 523 524 525 526 527

Access Control - 420 and 430 421 422 423 424 425 426 427 428 429 430 431 432 433 434 Access denied Access report by user Forced access Egress denied Egress granted Access door propped open Access point door status monitor trouble Access point request to exit Access program mode entry Access program mode exit Access threat level change Access relay/trigger fail Access RTE shunt Access DSM shunt 89 8A 8B 8C 8D 8E 8F 90 91 92 93 94 95 96

Modules - 530 531 532 Module added Module removed B1 B2

Communication Disables - 550 and 560 551 552 Dialer disabled Radio transmitter disabled B3 B4

Bypasses - 570 570 571 572 573 574 575 576 577 Zone bypass Fire bypass 24Hr. zone bypass Burglary bypass Group bypass Swinger bypass Access zone shunt Access point bypass B5 B6 B7 B8 B9 BA BB BC

Arming - 440 and 450 441 442 450 Armed Stay Keyswitch armed Stay Exception open/close 97 98 99

Test/Misc. - 600 601 602 Manual trigger test Periodic test report BD BE

Magellan

23

Appendix 5: Automatic Report Code List

System Event Arming with Master Code (##) Arming with User Code (##) Arming with Keyswitch (##) Auto Arming Arm with PC software Late To Close No Movement Partial arming Quick arming Closing Delinquency Disarm with Master Code (##) Disarm with User Code (##) Disarm with Keyswitch (##) Disarm after alarm* with Master Code (##) Disarm after alarm* with User Code (##) Disarm after alarm* with Keyswitch (##) Cancel alarm** with Master Code (##) Cancel alarm** with User Code (##) Cancel alarm** with Keyswitch (##) Auto Arming Cancellation Disarm with PC software Disarm after an alarm with PC software Quick disarm Zone Bypassed (##) Zone alarm (##) Fire alarm (##) Zone alarm restore (##) Fire alarm restore (##) Panic 1 - Emergency Panic 2 - Medical Panic 3 - Fire Recent closing Global zone shutdown Duress alarm Zone shutdown (##) Zone tampered (##) Zone tamper restore (##) Keypad Lockout Default Contact ID Report Code when using sections [790] to [795] 3 4A1 - Close by user 3 4A1 - Close by user 3 4A9 - Keyswitch Close 3 4A3 - Automatic Close 3 4A7 - Remote arm/disarm 3 4A4 - Late to Close 3 4A4 - Late to Close 1 574 - Group bypass 3 408 - Quick arm 1 654 - System Inactivity 1 4A1 - Open by user 1 4A1 - Open by user 1 4A9 - Keyswitch Open 1 4A1 - Open by user 1 4A1 - Open by user 1 4A1 - Keyswitch Open 1 4A6 - Open by user 1 4A6 - Open by user 1 4A6 - Keyswitch Open 1 4A5 - Deferred Open/Close 1 4A7 - Remote arm/disarm 1 4A7 - Remote arm/disarm 1 408 - Quick disarm 1 57A - Zone bypass 1 13A - Burglary Alarm 1 11A - Fire alarm 3 13A - Burglary Alarm Restore 3 11A - Fire alarm Restore 1 12A - Panic alarm 1 1AA - Medical alarm 1 115 - Pull Station 3 4AA - Open/Close 1 574 - Group bypass 1 121 - Duress 1 57A - Zone bypass 1 144 - Sensor tamper 3 144 - Sensor tamper restore 1 421 - Access denied Default SIA Report Code when using sections [790] to [795] CL - Closing Report CL - Closing Report CS - Closing Keyswitch CA - Automatic Closing CL - Closing Report OT - Late to Close NA - No Activity CG - Close Area CL - Closing Report CD - System Inactivity OP - Opening Report OP - Opening Report OS - Opening Keyswitch OP - Opening Report OP - Opening Report OS - Opening Keyswitch OR - Disarm from Alarm OR - Disarm from Alarm OS - Opening Keyswitch CE - Closing Extend OP - Opening Report OR - Disarm From Alarm OP - Opening Report UB - Untyped Zone Bypass BA - Burglary Alarm FA - Fire Alarm BH - Burglary Alarm Restore FH - Fire Alarm Restore PA - Panic Alarm MA - Medical Alarm FA - Fire Alarm CR - Recent Closing CG - Close Area HA - Hold-up Alarm UB - Untyped Zone Bypass TA - Tamper Alarm TR - Tamper Restoral JA - User Code Tamper

* An armed system is or was in alarm and was disarmed by a user. ** A disarmed system is or was in alarm (e.g. 24Hr. zone) and was disarmed by a user.

24

Programming Guide

System Event AC Failure Battery Failure Auxiliary supply trouble Bell output current limit Bell absent Clock lost Fire loop trouble TLM trouble restore AC Failure restore Battery Failure restore Auxiliary supply trouble restore Bell output current limit restore Bell absent restore Clock programmed Fire loop trouble restore Combus fault Module tamper Module ROM_RAM_error Module TLM trouble Module fail to communicate to monitoring station. Printer fault Module AC Failure Module battery failure Module Auxiliary supply trouble Bus fault restore Module tamper restore Module ROM_RAM_error restore Module TLM restore Printer fault restore Module AC restore Module battery restore Module Auxiliary supply restore Fail to communicate with monitoring station Module RF low battery Module RF battery restore Module RF supervision trouble Module RF supervision restore Cold Start Warm Start Test Report engaged PC software communication finished Installer on site Installer programming finished

Default Contact ID Report Code when using sections [790] to [795] 1 3A1 - AC loss 1 3A9 - Battery test failure 1 3AA - System trouble 1 321 - Bell 1 1 321 - Bell 1 1 626 - Time/Date inaccurate 1 373 - Fire trouble 3 351 - Telco 1 fault restore 3 3A1 - AC loss restore 3 3A9 - Battery test restore 3 3AA - System trouble restore 3 321 - Bell 1 restore 3 321 - Bell 1 restore 3 625 - Time/Date Reset 3 373 - Fire trouble restore 1 333 - Expansion module failure 1 145 - Expansion module tamper 1 3A4 - Rom checksum bad 1 352 - Telco 2 fault 1 354 - Fail to communicate 1 336 - Local printer failure 1 3A1 - AC loss 1 3A9 - Battery test failure 1 3AA - System trouble 3 333 - Expansion module failure restore 3 145 - Expansion module tamper restore 3 3A4 - Rom checksum bad restore 3 352 - Telco 2 fault restore 3 336 - Local printer failure restore 3 3A1 - AC loss restore 3 3A9 - Battery test failure restore 3 3AA - System trouble restore 1 354 - Fail to communicate 1 384 - RF transmitter low battery 3 384 - RF transmitter battery restore 1 381 - Loss of supervision - RF 3 381 - Supervision restore - RF 1 3A8 - System shutdown 1 3A5 - System reset 1 6A2 - Periodic test report 1 412 - Successful - download access 1 627 - Program mode Entry 1 628 - Program mode Exit

Default SIA Report Code when using sections [790] to [795] AT - AC Trouble YT - System Battery Trouble YP - Power Supply Trouble YA - Bell Fault YA - Bell Fault JT - Time Changed FT - Fire Trouble LR - Phone Line restoral AR - AC Restoral YR - System Battery Restoral YQ - Power Supply restored YH - Bell Restored YH - Bell Restored JT - Time Changed FJ - Fire Trouble Restore ET - Expansion Trouble TA - Tamper Alarm YF - Parameter Checksum Fail LT - Phone Line trouble YC - Communication Fails VT - Printer Trouble AT - AC Trouble YT - System Battery Trouble YP - Power Supply Trouble ER - Expansion Restoral TR - Tamper Restoral YG - Parameter Changed LR - Phone Line Restoral VR - Printer Restore AR - AC Restoral YR - System Battery Restoral YQ - Power Supply Restored YC - Communication Fails XT - Transmitter Battery Trouble XR - Transmitter Battery Restoral US - Untype Zone Supervision UR - Untyped Zone Restoral RR - Power Up YW - Watchdog Reset TX - Test Report RS - Remote Program Success LB - Local Program LS - Local Program Success

Magellan

25

Warranty Paradox Security Systems Ltd. ("Seller") warrants its products to be free from manufacturing defects in materials and workmanship for one-year following the date of manufacture. Seller will, within this period, at its option, repair or replace any product failing to operate correctly without charge to the original purchaser or user. This warranty will not apply to any equipment, or any parts thereof, which have been repaired by others, improperly installed, improperly used, abused, altered, damaged, subjected to acts of God, or on which any serial numbers have been altered, defaced or removed. Seller will not be responsible for any dismantling or reinstallation charges. THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, BEYOND THE DESCRIPTION HEREIN. THERE IS NO EXPRESS OR IMPLIED WARRANTY OF MERCHANTABILITY OR A WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY IS IN LIEU OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF SELLER, ITS SUPPLIERS AND/OR AFFILIATES. Any action for breach of warranty, including but not limited to any implied warranty of merchantability, must be brought within three months following the end of the warranty period. IN NO CASE WILL SELLER OR ITS AFFILIATES BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT. In case of defect, contact the security professional who installed and maintains your security system. In order to exercise the warranty, the product must be returned to the indicated RMA location by the security professional, shipping costs prepaid and insured. After repair or replacement, Seller assumes the cost of returning products under warranty. Seller will have no obligation under this warranty, or otherwise, if the product has been repaired by others, improperly installed, improperly used, abused, altered, damaged, subjected to accident, nuisance, flood, fire or acts of God, or on which any serial numbers have been altered, defaced or removed. Seller will not be responsible for any dismantling, reassembly or reinstallation charges. This warranty contains the entire warranty. Any prior agreements or representations, whether oral or written, are either merged herein or are expressly cancelled. Seller neither assumes, nor authorizes any other person purporting to act on its behalf to modify, to change, or to assume for it, any other warranty or liability concerning its products. Notwithstanding anything herein, in no event shall Seller or its affiliates be liable for an amount in excess of Seller's original selling price of the product, for any loss or damage, whether direct, indirect, incidental, consequential or otherwise arising out of any failure of the product. Seller's warranty, as hereinabove set forth, shall not be enlarged, diminished or affected by and no obligation or liability shall arise from Seller offering to render or rendering technical advice or services in connection with the purchase of goods hereunder. SELLER STRONGLY RECOMMENDS THAT THE ENTIRE SYSTEM BE COMPLETELY TESTED MONTHLY. Warning: Despite frequent testing, and due to, but not limited to, any or all of the following: criminal tampering, electrical or communication disruption, or improper use, it is possible for the system to fail to perform as expected. Seller does not represent that the product/system may not be compromised or circumvented or that the product or system will prevent any personal injury or property loss by burglary, robbery, fire or otherwise; nor that the product or system will in all cases provide adequate warning or protection. A properly installed and maintained alarm may only reduce risk of burglary, robbery, fire or otherwise but it is not insurance or a guarantee that these events will not occur. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE, OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. Therefore, the installer should in turn advise the consumer to take any and all precautions for his or her safety including, but not limited to, fleeing the premises and calling 911, the police and/or fire department, in order to mitigate the possibilities of harm and/or damage. Seller is not an insurer of either the property or safety of the user's family or employees, and limits its liability for any loss or damage including incidental or consequential damages to Seller's original selling price of the product in question, regardless of the cause of such loss and/or damage. Some locations do not allow limitations on how long an implied warranty lasts or do not allow the exclusion or limitation of incidental or consequential damages, or differentiate in their treatment of limitations of liabilities for ordinary or gross negligence, therefore the above limitations may be reduced and/or not apply to you. This warranty gives you specific legal rights and you may also have additional rights depending on the location. 2004-2005 Paradox Security Systems Ltd. All rights reserved. Specifications may change without prior notice. One or more of the following US patents may apply: 6215399, 6111256, 5751803, 5721542, 5287111, 5119069, 5077549, 5920259, 5886632. Canadian and international patents may also apply. Magellan is a trademark or registered trademark of Paradox Security Systems Ltd. or its affiliates in Canada, the United States and/or other countries. For technical support in Canada or the U.S., call 1-800-791-1919 for English or 1-866-912-0600 for French, Monday to Friday from 8:00AM to 8:00PM EST. For technical support outside Canada and the U.S., call 00-1-450-491-7444, Monday to Friday from 8:00AM to 8:00PM EST. Please feel free to check out our website at www.paradox.ca.

26

Programming Guide

Installer Menu Overview

ready to arm menu
Must enter the installer, maintenance or user code to access

1-bypass zones 2-alarm clock 3-time and date 4-system 1-language setup 2-user profile 3-communicator central report? voice report? utility report? pager report? add service tel? (MG-6060 only) 4-delays & tones add tel. # 1 add tel. # 1 add tel. # 1 add tel. # 1 tel.: add backup # add tel. # 2 add tel. # 2 add message? account number record alrm mes? report type? report format record alrm mes?

entry delay 1? entry delay 2? exit delay? bell cutoff del? bell squawk? test test test test zones? remotes? reporting? hardware?

type: type: type: type:

disarming trouble paramedic zone acti.

select select select select

user trouble user zone

5-system test

6-zone profile 7-output profile

select zone add add add add output1? output2? output3? output4?

open/close cover

modify label?

zone type

wireless output?

delete output? modify label? modify label? follow bell? remote access? alarm activation follow bell? zone activation? follow alarm? alarm activation follow arm? pulse on alarm? zone activation? follow stay arm? on for 1 sec? follow arm? console superv? on for 5 sec? follow stay arm? custom setup? on for 15 sec? console superv? no on for 30 sec? custom setup? modify button? on for 1 min? yes on for 5 min? press button on for 15 min? on for 30 min? follow zone? on for 1 sec? on for 5 sec? on for 15 sec? on for 30 sec? on for 1 min? on for 5 min? on for 15 min? on for 30 min? on all zones? master? yes user XX? Yes another output? on time? on zone open? remote button? on exit delay? when armed? on entry delay? on alarm? house code? toggle on/off? on for 1 sec? on for 5 sec? on for 15 sec? on for 30 sec? on for 1 min? on for 5 min? on for 15 min? on for 30 min? on all remotes? master? yes user XX? Yes another output?

8-signal strngth 9-passwords installer code maintenance code panel id pc password

5-chime zone 6-alarm memory 7-history log 8-utility setup 9-version number

1-radio on arm (MG-6060 only) 2-auto arming 3-auto arm time 4-lost remote 5-x10 setup (MG-6060 only) 6-backlight adj. 7-contrast adj. 8-ring setup (MG-6060 only) 9-demo mode

= Master Code only = Installer Code only

ring volume? ring tone?

780 Industriel Blvd., Saint-Eustache (Quebec) J7R 5V3 CANADA Tel.: (450) 491-7444 Fax: (450) 491-2313 www.paradox.ca PRINTED IN CANADA - 09/2005 MAGELLAN-EP05