ALIGNMENT ACCESSORIES

PART NUMBER
A800001 A800002 A800003 A800051

DESCRIPTION
CSI 8210 Laser Head Direct Connect Interface. Y-cable. CSI 8210 Laser Head Direct Connect End Cable (~ 8'). This extension cable goes from a straight Lemo Connector to a Right Angle Lemo Connector. Single, CSI 8210 Laser Head Direct Connect Extension Cable (~ 8'). This Extension Cable has a straight Lemo Connector on each end. Two B821007 Alignment Mounting Base Brackets, and two B8210-CHN Mounting Chain Assemblies, Standard.

A800052

Soft Mount Bracket (1 piece) for alignment of stationary shafts. The chain is 2' long 1/2" wide. For shaft sizes up to 8" with a single chain as delivered. To extend the maximum shaft diameter by an additional 8", purchase an additional chain extension (part number D22773). This can be done twice to accommodate a shaft diameter of 24". Set of Two Brackets, each Bracket consists of light-weight delron housing containing 7 powerful rare-earth magnets. The Bracket lip overhangs the coupling rim to provide extra stability. Brackets are only 9/16" (14 mm) thick and are designed to mount on the side of the coupling. With this accessory it is possible to attach the alignment fixtures within seconds of tagging out a machine for so-called hot alignment checks. For use on couplings made of ferromagnetic material. Recommended minimum coupling diameter is 3-4" (75-100 mm). The Belt Alignment System eliminates the need for straightedge or string alignment of belt or chain driven equipment. Standard Accessories: Laser Transmitter, three Magnetic Targets, Leather Case, Users Manual

A800056

A815000

A821510 B8100-EXT2

CSI 8215/8225 Laser Head Direct Connect Interface One 2" (51mm) Bracket Extension Block. Extension Blocks may be mounted on any bracket to achieve greater coupling clearances. The blocks are stackable up to a height of 7" (178mm) without impacting accuracy. One 4" (102mm) Bracket Extension Block. Extension Blocks may be mounted on any bracket to achieve greater coupling clearances. The blocks are stackable up to a height of 7" (178mm) without impacting accuracy. Two 8" Chain Extension Assemblies. Allows laser brackets to be attached to larger diameter shafts. CSI 8215/8225 Laser Head Mounting Post (quantity 1) Alignment Magnetic Mounting Bases (quantity 2). The Magnetic Mounting Base is ideal for straightness measurements. When the magnet is switched on, it can be mounted on any curved or flat ferrous metal surface, like rolls and machine bases, and moved forward or backward along the surface. When the magnet is switched off, the base provides enough support that the laser heads can be used on nonferrous material, i.e. granite rolls. Quick Mount Narrow Brackets (quantity 2). The 1/2 inch (13mm) wide Quick Mount Narrow Bracket is a chain type bracket for optimal stability in tight spaces on a wide range of shaft sizes. It is more reliable than any magnet mounted bracket for this diameter range. Full Kit (20 of each shim size) 3" x 3" (Also available in 2x2", 4x4", and 5x5"). Note: replacement shims (20 of each shim size) are also available. Call factory for details and pricing. Mini Kit (10 of each shim size), 3" x 3"(Also available in 2x2", 4x4", and 5x5"). Note: replacement shims (20 of each shim size) are also available. Call factory for details and pricing. Softmount Chain Extension for use with the Soft Mount Bracket (part # A800052). Nylon nuts that come in the package can be added to the chain to allow it to easily slide over the shaft while providing a stable mounting configuration. The chain is 2' long 1/2" wide. CSI 8215/8225 Laser Alignment Dual-Pass Mode Cable Super Fast Smart Charging Station recharges the laser heads in less than 15 minutes. The laser heads can be stored on the charging station until required. A power cord is included for charging the CSI 8117, 2120, or 2130 directly from the charging station.

B8100-EXT4

D22773 D23465 A8AA50

A8AA55

A8SHFK-B

A8SHMK-B

A832001

A8215C2-PM A8211

BALANCING KITS

PART NUMBER
A0404B1

DESCRIPTION
Infrared Phototach (1-20,000 RPM), with CSI 2130 Cable, standard magnet mount

A0404P1

404B Infrared Phototach Package, with external power supply, CSI 2130 Cable, standard magnet mount. The 404P Package includes the A404B Phototach Kit, with an external power supply instead of the cable for powering from the meter. Includes cables for connecting both to the CSI 2130 (Turck) and to older analyzers (BNC). Infrared Phototach (1-20,000 RPM), with (CSI 2120) Pig-Tail Cable, standard magnet mount

A404B

A040801 A173001 A1730B2

Battery Pack for 404P Phototach 2 - 4 Sensor Balancing Accessories Upgrade for the CSI 2130 2130 Advanced Balancing Expansion Pak. Advanced Balancing Package for CSI 2130 handles both single-, and multi-plane balancing tasks. It is designed to provide a new level of power and intelligence with a simple and intuitive user interface. NOTE: When adding the Balance Expansion Pak to an Alignment only CSI 2130, you must also order the A2130V1 Single Channel Vibration Upgrade. Reflective Tape for Phototach Units, 1/2" wide, 5' roll (minimum order 3 rolls) 404B Infrared Phototach Package, with external power supply, standard magnet mount Black 15' Cable, BNC to 2-pin mil

A403 A404P A6122BK

A6122BL

Blue 15' Cable, BNC to 2-pin mil

A6122GY

Grey 15' Cable, BNC to 2-pin mil

A6122RD

Red 15' Cable, BNC to 2-pin mil

A726-P

Portable Digital Scales: 0-200 g / 0.1 g increments

A728 A8BA1 A8BA25

Clip-on Balancing Trial Weight Kit. Variety of clip on trial weights for balancing. Designed to clip on inner edge of fan blades. Balancing Compass. Balancing Compass is used to assist in locating angular position during balancing. The compass is magnetically mounted with clockwise and counter-clockwise 0-360 scaling. Weight Kit with Field Balance Scales

B40401 B40405 B404-BASE D24862 D24042 D24861 A090835

Signal/Power Pigtail Cable, 18" long, for 404B Phototach Replacement Photo-Element, Cable and Bracket (for 404 to 404B Phototach Upgrade). Can be used to upgrade a 404 Photo Element to a 404B Element, to allow powering from the CSI 2120/CSI 2130, without having to replace the entire Phototach. Adjustable Magnetic Base for 404 Phototach CSI 2130 Tach Input Cable, BNC to Turck, 4' long Standard Accelerometer Coiled Cable, 3' long retracted, MS(2-pin) to DB25(M) CSI 2130 Tach Input Cable, 404B Connector to Turck, 2 meters long 2-Pole Small Magnet, 1" diameter 34 lb pull, 1/4-28 tapped hole, knurled finish