Scribd Logo
Upload

Welcome to Scribd!

  • 96 views

    Veritas Quick Start Guide Userguides

    Uploaded by

    Darren Whiteley
    This document provides a quick start guide for setting up a basic alarm system using the Veritas panel. It describes connecting the panel, keypad, detection devices, and bell box. It recommends planning a simple 2-zone system for an out-of-the-box solution. On first power up, the panel must be defaulted by pressing the reset button twice within 10 seconds of power. The system defaults and basic operation are then outlined.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    Veritas Quick Start Guide Userguides

    Uploaded by

    Darren Whiteley
    96 views2 pages
    This document provides a quick start guide for setting up a basic alarm system using the Veritas panel. It describes connecting the panel, keypad, detection devices, and bell box. It recommends planning a simple 2-zone system for an out-of-the-box solution. On first power up, the panel must be defaulted by pressing the reset button twice within 10 seconds of power. The system defaults and basic operation are then outlined.

    Original Description:

    quick start

    Original Title

    Veritas Quick Start Guide Userguides (2)

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides a quick start guide for setting up a basic alarm system using the Veritas panel. It describes connecting the panel, keypad, detection devices, and bell box. It recommends planning a simple 2-zone system for an out-of-the-box solution. On first power up, the panel must be defaulted by pressing the reset button twice within 10 seconds of power. The system defaults and basic operation are then outlined.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    96 views2 pages

    Veritas Quick Start Guide Userguides

    Uploaded by

    Darren Whiteley
    This document provides a quick start guide for setting up a basic alarm system using the Veritas panel. It describes connecting the panel, keypad, detection devices, and bell box. It recommends planning a simple 2-zone system for an out-of-the-box solution. On first power up, the panel must be defaulted by pressing the reset button twice within 10 seconds of power. The system defaults and basic operation are then outlined.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    Veritas Alarm Panel Quick Start Guide Introduction

    The Veritas is an 8 zone panel, which can be used out of the box with a minimum of additional programming. This document is designed for use with all of the Veritas variants and describes how to use the product with its default settings for an out of the box solution. The following paragraphs provide a quick start description of how to set up a simple alarm system, more detailed descriptions are provided in the installation manual and these are cross referenced below where they may be of use.

    Quick Start Set Up


    Requirements
    The following parts or facilities will be required for a successful installation.

    Installation
    Select suitable locations for the panel, keypad, detection devices and bell box, fix each device to the wall in its selected location and run cables from the panel to each device as follows.

    Veritas Control Panel. Veritas Keypad (some panels have built in keypads). Detection Devices. Bell Box (Odyssey described here). Mains Supply (Fused Spur).

    Keypad Bell Box 6 Core Cable Detection Devices 6 Core Cable


    Magnetic door contacts only require 4 core cable.

    Plan the System


    Before starting any work consider how the system will operate and where equipment needs to mounted. It is assumed that this will be a simple system and it is recommended that Zone 1 be entry exit (ie front door) and Zone 2 guard access (ie hall), with the panel being armed by timed exit. This matches the panel defaults (see system defaults below) and minimises the programming required. The system should also be planned so that zones 5, 6 and 7 are omitted in part set.

    Connect the detection devices to the zone connections in the panel. Refer to Zone Connections in the Installation section (section 3) of the installation manual for details of how to wire detection devices to zones. The Veritas has a global tamper circuit, all of the detector tampers will need to be connected in series before being connected to the global tamper terminals. See Global System Tamper in the Installation section (section 3) of the installation manual. If more than one remote keypad is fitted, the keypads will need to be addressed, see Installing Remote Keypads in the Installation section of the manual. The panel will require a mains supply, connect mains via a fused spur as described in Connecting AC Mains in the Installation section of the installation manual.

    In part set, Zone 1 becomes a full guard (instant alarm) and Zone 2 becomes entry exit. This can be changed using programming options 21 and 23.

    The keypad should be mounted at a convenient location, easily accessible from the normal entrance and from the sleeping quarters in a domestic installation. The bell box should normally be mounted so that it is visible when approaching the entrance. After an alarm the strobe will continue to flash after the bell cut off, warning the occupant that intruders may be on the premises.

    Applying Power
    On first power up, the Veritas should be defaulted. To default the panel on power up do the following: Connect mains to the panel, then within 10 secconds (while all zone lights are lit) press the reset button on the keypad twice. After a few more seconds the zone lights will go out and the panel will start to set enter your default user code () to stop the system from setting and silence it. Once the panel has been defaulted and silenced as described above, connect the backup battery.


    INS 507-1

    Some Veritas manuals recommend connecting the battery before the mains, this is incorrect and the sequence described above is the recommended way to power up and default the Veritas.

    System Defaults

    Engineer Code 1234. User Code 4321. Zone 1 Entry/Exit in full set. Zone2 Inhibited entry in full set. Zones 3-8 Guard. Part arm Zones 1-4 and 8 active Zones 5-7 omitted. Zone 1 Guard in part set. Zone 2 Entry/Exit in part set. Exit time 30 secs. Entry time 30 secs. Bell cut-off time 15 mins

    Operating the Alarm


    Alarm operation is described in detail in the Master User Guide (R8Plus and Excel only) and User Guide. Users can arm, disarm, silence after an alarm condition and reset after and alarm (unless the alarm is programmed to engineer reset see Miscellaneous Selections ). Users can also perform certain programming tasks and system tests. On the R8Plus and Excel certain types of user have limited access to these functions (See Programming Access Codes). Engineers can program the system, perform system tests and reset the system after an alarm activation (if the system is set for Engineer reset). Engineers cannot unset the system. By default the Veritas operates on a single button set principle. This means that the user code is not required to arm the system simple press the or button.This function can be changed in Miscellaneous Selections

    Programming
    Detailed descriptions of the programming options are set out in section 4 of the installation manual. Refer to section Programming Zone Types (programming options to ) of the installation manual to program any zones that you want to be different to the defaults. Set up the user code and engineer code (both use option ) see Programming Codes in the manual.

    The sequence for changing the user code and engineers code is the same, the code enetered at the start of the sequence determines which one is being programmed.

    The Veritas R8Plus and Excel support multiple user codes. See Assigning User Codes in the manual. When assigning user codes to the R8Plus and Excel there are a few points it is important to be aware of.

    The user type must be defined (program options ) as well as assigning a code (options -). Engineer codes cannot be set up by a user. User codes cannot be set up by a user. The same code cannot be used twice.

    The panel is now ready to use.

    Testing and Diagnostics


    The Veritas includes some useful tools for testing the system.

    Bell Test (Programming Option )

    Provides manual testing for the Bell, Strobe and internal sounders.

    Walk Test (Programming Option or )

    Allows all of the detection zones to be checked without having to set the system.

    System Log (Programming Options - )

    The event log lists the last 7 alarm events, check the log to see what has caused an alarm, this can be useful in solving false alarms. INS 507-1

    You might also like