Scribd Logo
Upload

Welcome to Scribd!

  • 388 views

    MOS For Drainage Pipe Installation

    Uploaded by

    pulangratz
    This document outlines the steps for installing drainage pipes inside a toilet. Key steps include: 1. Opening approved shop drawings showing pipe locations and ensuring block work is complete before starting. 2. Cutting blocks to bury pipes at the required depths and slopes as indicated on drawings. 3. Joining pipes and fittings using the approved glue and installing them at the correct heights and slopes. 4. Connecting drainage pipes from other fixtures to the gully trap floor drain as shown on drawings and leak testing the installed system.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOC, PDF, TXT or read online from Scribd

    MOS For Drainage Pipe Installation

    Uploaded by

    pulangratz
    388 views2 pages
    This document outlines the steps for installing drainage pipes inside a toilet. Key steps include: 1. Opening approved shop drawings showing pipe locations and ensuring block work is complete before starting. 2. Cutting blocks to bury pipes at the required depths and slopes as indicated on drawings. 3. Joining pipes and fittings using the approved glue and installing them at the correct heights and slopes. 4. Connecting drainage pipes from other fixtures to the gully trap floor drain as shown on drawings and leak testing the installed system.

    Original Description:

    Standard Drainage Pipe

    Original Title

    MOS for Drainage Pipe Installation

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    DOC, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document outlines the steps for installing drainage pipes inside a toilet. Key steps include: 1. Opening approved shop drawings showing pipe locations and ensuring block work is complete before starting. 2. Cutting blocks to bury pipes at the required depths and slopes as indicated on drawings. 3. Joining pipes and fittings using the approved glue and installing them at the correct heights and slopes. 4. Connecting drainage pipes from other fixtures to the gully trap floor drain as shown on drawings and leak testing the installed system.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    388 views2 pages

    MOS For Drainage Pipe Installation

    Uploaded by

    pulangratz
    This document outlines the steps for installing drainage pipes inside a toilet. Key steps include: 1. Opening approved shop drawings showing pipe locations and ensuring block work is complete before starting. 2. Cutting blocks to bury pipes at the required depths and slopes as indicated on drawings. 3. Joining pipes and fittings using the approved glue and installing them at the correct heights and slopes. 4. Connecting drainage pipes from other fixtures to the gully trap floor drain as shown on drawings and leak testing the installed system.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    of 2

    METHOD OF STATEMENT FOR DRAINAGE PIPE INSTALLATION INSIDE THE TOILET

    METHOD OF STATEMENT FOR DRAINAGE PIPE INSTALLATION INSIDE THE TOILET


    1. Open an approved shop drawings. This shop drawings consist of approved Toilet details and mechanical pipe sleeves location for both indoor unit refrigeration pipes and sanitary fixtures ventilation. Block work (except the shaft walls) and water proofing activity should be done first before installation. . !aiting pipes" stub pipes and fittings from risers and underground pipes should be present before starting inside the toilet. #ollow vertical shaft or duct located nearby the toilet will not be cover to work easily inside the toilet especially connection to the risers. $. %ssign the location of pipes in the wall or floor that is exactly as mention on the approved toilet details shop drawing. &ark with the line corresponds to the total area to bury the pipe in the wall or floor (for lavatory and %'( drain). ). *se block cutter or simply portable grinder to cut a side of block continuously along the line that had been marked. %bsolute care should be done not to cut or damaged the pre+installed pipe sleeves of fixture vents and %'( indoor unit. ,. By using sharp+ pointed steel rod and other proper chipping tools" chip the block side to the thickness re-uired to fixed the sanitary pipes. .. /tandard fittings and materials must be used and all pipes and fittings must be 0oined using the approved glue. /anitary tee fittings for vent be fixed inclined ),1 or slope from center line of pipe it serve. 2. 3evel of the slab should be identified by surveyor before proceeding installation. %lso locate points as alternative reference point for pipe and pipe fittings installation. 4. 5nstall ' layout the pipes at designated height" location and slopes (16 slope for sanitary fixtures and 7.,6 slope for %'( drain). /anitary fixtures outlet location should also be installed and identified.

    ',' 71) doc. 787 )7$$

    8. (onnection of drainage pipes other than water closet drain (i.e. %'( drain" lavatory drain" bidet drain" bathtub drain and shower tray drain) should be slope toward gully trap floor drain based on the approved toilet details shop drawings. 17. 9ipes and pipe fittings connection should be on the compacted fine sand and partly small of cement mortar as its support. #eight distance between gully trap bottom and slab should be two ( ) centimeter for all toilets. 11. %bsolute care should be imposed not to damage the water proofing upon installation. 1 . 5nstall sleeves for pipes passing through the concrete or masonry walls. 9ut sealant in between the pipes and sleeves. 1$. (heck the pipes securely fixed" 0oint and capped before leak testing. 1). 3eak test for the installed pipes is to be carried+out with presence of inspector :ngineer. 1,. %fter the approval of 5nspector :ngineer" cover the pipes with cement plaster or sand to where it is applicable. END

    ',' 71) doc. 787 )7$$

    You might also like