Ansi - Isa-75 08 01-2002

AMERICAN NATIONAL STANDARD
ANSI/ISA-75.08.01-2002 (R2007)
Formerly ISA-75.03-1992
Face-to-Face Dimensions for Integral Flanged Globe-Style Control Valve Bodies (Classes 125, 150, 250, 300, and 600)
Approved 23 April 2007
NOTICE OF COPYRIGHT This is a copyright document and may not be copied or distributed in any form or manner without the permission of ISA. This copy of the document was made for the sole use of the person to whom ISA provided it and is subject to the restrictions stated in ISAs license to that person. It may not be provided to any other person in print, electronic, or any other form. Violations of ISAs copyright will be prosecuted to the fullest extent of the law and may result in substantial civil and criminal penalties.
Copyright The Instrumentation, Systems, and Automation Society Provided by IHS under license with ISA No reproduction or networking permitted without license from IHS
--`,,```,,,,````-`-`,,`,,
Not for Resale
ANSI/ISA-75.08.01-2002 (R2007) Face-to-Face Dimensions for Integral Flanged Globe-Style Control Valve Bodies (Classes 125, 150, 250, 300, and 600) ISBN: 978-1-934394-14-4 Copyright 2007 by ISA. All rights reserved. Not for resale. Printed in the United States of America. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means (electronic mechanical, photocopying, recording, or otherwise), without the prior written permission of the Publisher. ISA 67 Alexander Drive P.O. Box 12277 Research Triangle Park, North Carolina 27709
Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
ANSI/ISA-75.08.01-2002 (R2007)
Preface
This preface, as well as all footnotes and annexes, is included for information purposes and is not part of ANSI/ISA-75.08.01-2002 (R2007). The standards referenced within this document may contain provisions which, through reference in this text, constitute requirements of this document. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this document are encouraged to investigate the possibility of applying the most recent editions of the standards indicated within this document. Members of IEC and ISO maintain registers of currently valid International Standards. ANSI maintain registers of currently valid U.S. National Standards. This document has been prepared as part of the service of ISA toward a goal of uniformity in the field of instrumentation. To be of real value, this document should not be static but should be subject to periodic review. Toward this end, the Society welcomes all comments and criticisms and asks that they be addressed to the Secretary, Standards and Practices Board; ISA; 67 Alexander Drive; P. O. Box 12277; Research Triangle Park, NC 27709; Telephone (919) 549-8411; Fax (919) 549-8288; E-mail: [email protected]. The ISA Standards and Practices Department is aware of the growing need for attention to the metric system of units in general, and the International System of Units (SI) in particular, in the preparation of instrumentation standards. The Department is further aware of the benefits to USA users of ISA standards of incorporating suitable references to the SI (and the metric system) in their business and professional dealings with other countries. Toward this end, this Department will endeavor to introduce SI-acceptable metric units in all new and revised standards, recommended practices, and technical reports to the greatest extent possible. Standard for Use of the International System of Units (SI): The Modern Metric System, published by the American Society for Testing & Materials as IEEE/ASTM SI 1097, and future revisions, will be the reference guide for definitions, symbols, abbreviations, and conversion factors. It is the policy of ISA to encourage and welcome the participation of all concerned individuals and interests in the development of ISA standards, recommended practices, and technical reports. Participation in the ISA standards-making process by an individual in no way constitutes endorsement by the employer of that individual, of ISA, or of any of the standards, recommended practices, and technical reports that ISA develops. CAUTION ISA ADHERES TO THE POLICY OF THE AMERICAN NATIONAL STANDARDS INSTITUTE WITH REGARD TO PATENTS. IF ISA IS INFORMED OF AN EXISTING PATENT THAT IS REQUIRED FOR USE OF THE STANDARD, IT WILL REQUIRE THE OWNER OF THE PATENT TO EITHER GRANT A ROYALTY-FREE LICENSE FOR USE OF THE PATENT BY USERS COMPLYING WITH THE STANDARD OR A LICENSE ON REASONABLE TERMS AND CONDITIONS THAT ARE FREE FROM UNFAIR DISCRIMINATION. EVEN IF ISA IS UNAWARE OF ANY PATENT COVERING THIS STANDARD, THE USER IS CAUTIONED THAT IMPLEMENTATION OF THE STANDARD MAY REQUIRE USE OF TECHNIQUES, PROCESSES, OR MATERIALS COVERED BY PATENT RIGHTS. ISA TAKES NO POSITION ON THE EXISTENCE OR VALIDITY OF ANY PATENT RIGHTS THAT MAY BE INVOLVED IN IMPLEMENTING THE STANDARD. ISA IS NOT RESPONSIBLE FOR IDENTIFYING ALL PATENTS THAT MAY REQUIRE A LICENSE BEFORE IMPLEMENTATION OF THE STANDARD OR FOR INVESTIGATING THE VALIDITY OR SCOPE OF ANY PATENTS BROUGHT TO ITS ATTENTION. THE USER SHOULD CAREFULLY INVESTIGATE RELEVANT PATENTS BEFORE USING THE STANDARD FOR THE USERS INTENDED APPLICATION.
--`,,```,,,,````-`-`,,`,,`,`,,`---
Not for Resale
ANSI/ISA-75.08.01-2002 (R2007)
-4-
HOWEVER, ISA ASKS THAT ANYONE REVIEWING THIS STANDARD WHO IS AWARE OF ANY PATENTS THAT MAY IMPACT IMPLEMENTATION OF THE STANDARD NOTIFY THE ISA STANDARDS AND PRACTICES DEPARTMENT OF THE PATENT AND ITS OWNER. ADDITIONALLY, THE USE OF THIS STANDARD MAY INVOLVE HAZARDOUS MATERIALS, OPERATIONS OR EQUIPMENT. THE STANDARD CANNOT ANTICIPATE ALL POSSIBLE APPLICATIONS OR ADDRESS ALL POSSIBLE SAFETY ISSUES ASSOCIATED WITH USE IN HAZARDOUS CONDITIONS. THE USER OF THIS STANDARD MUST EXERCISE SOUND PROFESSIONAL JUDGMENT CONCERNING ITS USE AND APPLICABILITY UNDER THE USERS PARTICULAR CIRCUMSTANCES. THE USER MUST ALSO CONSIDER THE APPLICABILITY OF ANY GOVERNMENTAL REGULATORY LIMITATIONS AND ESTABLISHED SAFETY AND HEALTH PRACTICES BEFORE IMPLEMENTING THIS STANDARD. THE USER OF THIS DOCUMENT SHOULD BE AWARE THAT THIS DOCUMENT MAY BE IMPACTED BY ELECTRONIC SECURITY ISSUES. THE COMMITTEE HAS NOT YET ADDRESSED THE POTENTIAL ISSUES IN THIS VERSION. The following people served as members of ISA Committee SP75.08 and approved ANSI/ISA-75.08.01-2002: NAME W. Weidman, Chairman H. Baumann G. Borden R. Brodin F. Cain R. Chown B. Hatton J. Reed H. Sonderegger COMPANY Parsons Energy & Chemicals Group HB Services Partners LLC Consultant Consultant Flowserve Corporation OTEC Process Systems Inc. Dezurik Consultant Anvil International Inc.
--`,,```,,,,````-`-`,,`,,`,`,,`---
The following people served as members of ISA Committee SP75 and approved ANSI/ISA-75.08.01-2002: NAME D. Buchanan, Chairman W. Weidman, Managing Director K. Schoonover, Secretary A. Abromaitis H. Backinger G. Barb H. Baumann J. Beall* W. Black G. Blackwell H. Boger* G. Borden S. Boyle R. Brodin* F. Cain A. Engels H. Fuller J. George COMPANY Consultant Parsons Energy & Chemicals Group Con-Tek Valves Inc. Red Valve Co Inc. Consultant Consultant HB Services Partners LLC Emerson Process Management Curtiss-Wright Flow Control Corporation Industrial Valve Masoneilan Dresser Consultant Metso Automation USA Inc. Emerson Process Management Flowserve Corporation Praxair Inc. Valvcon Corporation Richards Industries
Not for Resale
ANSI/ISA-75.08.01-2002 (R2007)
L. Griffith J. Jamison R. Jeanes J. Kersh C. Langford W. Lestan* A. Libke* R. Louviere J. McCaskill A. McCauley R. McEver* H. Miller T. Molloy L. Ormanoski J. Ozol W. Rahmeyer J. Reed A. Shea* E. Skovgaard H. Sonderegger ______ * One vote per company.
Consultant Bantrel Inc. TXU Electric M W Kellogg Company Cullen G. Langford Inc. Masoneilan Dresser SPX Valves & Controls DeZurik Products Services Unlimited Power Chokes Chagrin Valley Controls Inc. Emerson Valve Automation Control Components Inc. CMES Inc. Frick Company Northern States Power Utah State University Norriseal SPX Valves & Controls DeZurik Products Leslie Controls Inc. Anvil International Inc.
ANSI/ISA-75.08.01-2002 was approved for publication by the ISA Standards and Practices Board on 26 September 2002. NAME M. Zielinski D. Bishop D. Bouchard M. Cohen M. Coppler B. Dumortier W. Holland E. Icayan A. Iverson R. Jones V. Maggioli T. McAvinew A. McCauley, Jr. G. McFarland R. Reimer J. Rennie H. Sasajima I. Verhappen R. Webb W. Weidman J. Weiss M. Widmeyer R. Wiegle C. Williams G. Wood COMPANY Emerson Process Management David N Bishop, Consultant Paprican Consultant Ametek, Inc. Schneider Electric Southern Company ACES Inc Ivy Optiks Dow Chemical Company Feltronics Corporation I&C Engineering, LLC Chagrin Valley Controls, Inc. Westinghouse Process Control Inc. Rockwell Automation Factory Mutual Research Corporation Yamatake Corporation Syncrude Canada Ltd. POWER Engineers Parsons Energy & Chemicals Group KEMA Consulting Stanford Linear Accelerator Center CANUS Corporation Eastman Kodak Company Graeme Wood Consulting
Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
ANSI/ISA-75.08.01-2002 (R2007)
-6-
The following people served as members of ISA Subcommittee SP75.08 and reaffirmed ANSI/ISA-75.08.01-2002 (R2007): NAME W. Weidman, Chair H. Baumann G. Borden F. Cain R. Chown R. Duimstra V. Mezzano J. Reed J. Young COMPANY Worley Parsons Consultant Consultant Flowserve Corporation Otec Process Systems Inc. Fisher Controls International Inc. Fluor Corporation Consultant Dow Chemical Company
The following people served as members of ISA Committee SP75 and reaffirmed ANSI/ISA-75.08.01-2002 (R2007): NAME J. Young, Chair W. Weidman, Managing Director H. Backinger H. Baumann J. Beall W. Black H. Boger G. Borden S. Boyle J. Broyles F. Cain W. Cohen R. Duimstra J. Faramarzi J. George H. Hoffmann J. Jamison R. Jeanes C. Langford A. Libke G. Liu J. McCaskill A. McCauley R. McEver V. Mezzano T. Molloy L. Ormanoski J. Ozol W. Rahmeyer J. Reed E. Skovgaard COMPANY Dow Chemical Company Worley Parsons Consultant Consultant Emerson Process Management Curtiss-Wright Flow Control Corporation Masoneilan Dresser Consultant Metso Automation USA Inc. Enbridge Pipelines Inc. Flowserve Corporation KBR Fisher Controls International Inc. Control Components Inc. Richards Industries Samson AG OPTI Canada Inc. TXU Electric Cullen G Langford Inc. DeZURIK Water Controls Syncrude Canada Ltd. Power Chokes Chagrin Valley Controls Inc. Consultant Fluor Corporation CMES Inc. York Process Systems NMC Prairie Island Nuclear Plant Utah State University Consultant Control Valve Solutions
--`,,```,,,,````-`-`,,`,,`,`,,`---
Not for Resale
ANSI/ISA-75.08.01-2002 (R2007)
This standard was approved for reaffirmation by the ISA Standards and Practices Board on 5 April 2007: NAME T. McAvinew, Vice President M. Coppler B. Dumortier D. Dunn W. Holland E. Icayan J. Jamison K. Lindner V. Maggioli A. McCauley G. McFarland R. Reimer N. Sands H. Sasajima T. Schnaare J. Tatera I. Verhappen R. Webb W. Weidman J. Weiss M. Widmeyer M. Zielinski COMPANY Jacobs Engineering Group Ametek Inc. Schneider Electric Aramco Services Company Consultant ACES Inc. Husky Energy Inc. Endress+Hauser Process Solutions AG Feltronics Corporation Chagrin Valley Controls Inc. Emerson Process Mgmt Power & Water Solutions Rockwell Automation E I du Pont Yamatake Corporation Rosemount Inc. Tatera & Associates Inc. MTL Instrument Group Robert C Webb PE Worley Parsons Applied Control Solutions LLC Consultant Emerson Process Management
--`,,```,,,,````-`-`,,`,,`,`,,`---
Not for Resale
This page intentionally left blank.
Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
ANSI/ISA-75.08.01-2002 (R2007)
Contents
1 2 3 4 5 Scope ................................................................................................................................................... 11 Purpose................................................................................................................................................ 11 Definitions ............................................................................................................................................ 11 Dimensional data ................................................................................................................................. 11 References........................................................................................................................................... 13
--`,,```,,,,````-`-`,,`,,`,`,,`---
Not for Resale
Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
11
ANSI/ISA-75.08.01-2002 (R2007)
Scope
This standard applies to integral flanged globe-style control valves, sizes 15 mm (1/2 inch) through 400 mm (16 inches), having top, top and bottom, port, or cage guiding.
Purpose
The purpose of this standard is to aid users in their piping design by providing Class 125 flat face, and Classes 150, 250, 300, and 600 raised face, flanged control valve dimensions, without giving special consideration of the equipment manufacturer to be used.
3
--`,,```,,,,````-`-`,,`,,`,`,,`---
Definitions
For definitions of terms used in this standard, see ANSI/ISA-75.05.01-2000 (R2005), Control Valve Terminology.
4
4.1
Dimensional data
Face-to-face dimensions for integral flanged globe-style control valves. See Table 1.
4.2 For end-to-end dimensions of flanged with ring joint ends, Dimension "A" shall be adjusted accordingly to ASME B16.10-2000 (R2003), paragraph 3.3.
Not for Resale
ANSI/ISA-75.08.01-2002 (R2007)
- 12 -
Table 1 Face-to-face dimensions for integral flanged globe-style control valves

Nominal valve Size PN 20 (Classes 125 and 150) Dimension A mm 15 20 25 40 50 65 80 100 150 200 250 300 350 400 Inches 1 1-1/2 2 2-1/2 3 4 6 8 10 12 14 16 mm 184 184 184 222 254 276 298 352 451 543 673 737 889 1016 Inches 7.25 7.25 7.25 8.75 10.00 10.88 11.75 13.88 17.75 21.38 26.50 29.00 35.00 40.00 PN 50 (Classes 250 and 300) Dimension A mm 190 194 197 235 267 292 318 368 473 568 708 775 927 1057 inches 7.50 7.62 7.75 9.25 10.50 11.50 12.50 14.50 18.62 22.38 27.88 30.50 36.50 41.62 mm 203 206 210 251 286 311 337 394 508 610 752 819 972 1108 PN 110 (Class 600) Tolerance
Dimension A inches 8.00 8.12 8.25 9.88 11.25 12.25 13.25 15.50 20.00 24.00 29.62 32.25 38.25 43.62 mm 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 3.2 3.2 3.2 inches 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.062 0.125 0.125 0.125
ISO 7005-1 designates classes 150 and 300 as PN20 and PN50, respectively. ISO 7005-2 designates classes 125 and 250 as PN20 and PN50, respectively.
--`,,```,,,,````-`-`,,`,,`,`,,`---
NOTE 1
Class 125 and PN 20 grey cast iron flanges. Classes 150 and 300 cast copper alloy flanges.
NOTE 2 Classes 150, 300, and 600, and PN20, PN50, and PN110 cast steel/alloy steel flanges. Class 600 cast copper alloy flanges. Class 250 and PN50 grey cast iron flanges. Classes 150 and 300, and PN20 and PN50 cast ductile iron flanges.
Not for Resale
13
ANSI/ISA-75.08.01-2002 (R2007)
References
The following bibliography is included for the definition of pressure classes and flange dimensions, material identification, and cross-reference information. AMERICAN SOCIETY OF MECHANICAL ENGINEERS (ASME) ASME B16.1-1998 ASME B16.5-2003 ASME B16.10-2000 (R2003) ASME B16.24-2001 Cast Iron Pipe Flanges and Flanged Fittings, Classes 25, 125, and 250 Pipe Flanges and Flanged Fittings: NPS 1/2 through 24 Face-to-Face and End-to-End Dimensions of Valves Cast Copper Alloy Pipe Flanges and Flanged Fittings: Class 150, 300, 400, 600, 900, 1500, and 2500 Valves Flanged, Threaded and Welding End Ductile Iron Pipe Flanges and Flanged Fittings: Classes 150 and 300 ASME Three Park Avenue New York, NY 10016-5990 Tel: 800-843-2763 http://www.asme.org
ASME B16.34-2004 ASME B16.42-1998 Available from:
INTERNATIONAL ELECTROTECHNICAL COMMISSION (IEC) IEC 60534-3-1 (2000) Industrial-Process Control Valves - Part 3-1: Dimensions - Face-to-Face Dimensions for Flanged, Two-Way, Globe-Type, Straight Pattern and Centre-to-Face Dimensions for Flanged, Two-Way, Globe-Type, Angle Pattern Control Valves IEC 3, rue de Varemb P.O. Box 131 CH - 1211 Geneva 20 Switzerland http://www.iec.ch
Available from:
INTERNATIONAL STANDARDS ORGANIZATION (ISO) ISO 7005-1:1992 ISO 7005-2:1988 Metallic Flanges Part 1: Steel Flanges Metallic Flanges Part 2: Cast Iron Flanges
--`,,```,,,,````-`-`,,`,,`,`,,`---
Not for Resale
ANSI/ISA-75.08.01-2002 (R2007)
- 14 -
Available from:
ISO 1, rue de Varemb P.O. Box 56 CH-1211 Geneva 20 Switzerland http://www.iso.ch
--`,,```,,,,````-`-`,,`,,`,`,,`---
Not for Resale
15
ANSI/ISA-75.08.01-2002 (R2007)
Annex A Dimensions for metrically sized valves

This annex is not part of ANSI/ISA-75.08.01-2002 (R2007), but it is included to facilitate its use. The ASME standards listed in the bibliography contain valve body design information in addition to faceto-face dimensions. Dimensions for metrically sized valves are nominal conversions that are conventionally used in documents by the Manufacturers Standardization Society (MSS) of the Valve and Fitting Industry (MSS-SP-86-2002), by the International Organization for Standardization (ISO), and by the International Electrotechnical Commission (IEC). Control valve initial dimensions, 10 inches - 16 inches, were listed in the Fluid Control Institute (FCI) Standard, FCI-65-2-1975, which has been withdrawn from publication.
Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
--`,,```,,,,````-`-`,,`,,`,`,,`---
Not for Resale
Developing and promulgating sound consensus standards, recommended practices, and technical reports is one of ISAs primary goals. To achieve this goal the Standards and Practices Department relies on the technical expertise and efforts of volunteer committee members, chairmen and reviewers. ISA is an American National Standards Institute (ANSI) accredited organization. ISA administers United States Technical Advisory Groups (USTAGs) and provides secretariat support for International Electrotechnical Commission (IEC) and International Organization for Standardization (ISO) committees that develop process measurement and control standards. To obtain additional information on the Societys standards program, please write: ISA Attn: Standards Department 67 Alexander Drive P.O. Box 12277 Research Triangle Park, NC 27709 ISBN: 978-1-934394-14-4
--`,,```,,,,````-`-`,,`,,`,`,,`---
Not for Resale

Ansi - Isa-75 08 01-2002

Uploaded by

Copyright:

Available Formats

Ansi - Isa-75 08 01-2002

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ansi - Isa-75 08 01-2002

Uploaded by

Copyright:

Available Formats

AMERICAN NATIONAL STANDARD

Approved 23 April 2007

Not for Resale

Not for Resale

Not for Resale

Not for Resale

Not for Resale

Not for Resale

Not for Resale

This page intentionally left blank.

Not for Resale

Not for Resale

This page intentionally left blank.

Not for Resale

Not for Resale

Table 1 Face-to-face dimensions for integral flanged globe-style control valves

Not for Resale

ASME B16.34-2004 ASME B16.42-1998 Available from:

Not for Resale

ISO 1, rue de Varemb P.O. Box 56 CH-1211 Geneva 20 Switzerland http://www.iso.ch

Not for Resale

Annex A Dimensions for metrically sized valves

Not for Resale

This page intentionally left blank.

Not for Resale

Not for Resale

Not for Resale

You might also like