Provisional Water Bore Completion

REPLACEMENT INFLATABLE PACKERS & ELEMENTS PTY LTD
29 WHEELER STREET, BELMONT, WESTERN AUSTRALIA 6104 PH: .61 (08) 9475 0700, Fax: .61 (08) 9475 0770 packersripe-packers.com www.ripe-packers.com
PROVISIONAL WATER BORE COMPLETION

270613NBKO
BEFORE HEADWORKS INSTALLATION 125mm NB FRP CASING WITH 80mm NB SCREENS TELESCOPED
Anticipated Casing String Run Casing float shoe 396.00 - 395.55 Drill-out Pipe 395.55 - 390.05 Centron x/over 390.05 - 389.60 45 lengths FRP 389.60 - +0.68 Stick-Up is 0.68metres
273.10mm OD STEEL SURFACE CASING PRESSURE GROUTED IN AT - 66 METERS
FRP Casing Grades DHC200 30 joints 0-266 Approx DHC250 9 joints 266 - 389 Approx
ENTRALISERS 1 PER CASING LENGTH
125mm NB FRP MAIN CASING WITH RELEVANT GRADE TO SUIT DEPTH - PRESSURE GROUTED IN
Screen Assembly SS end plate 80mm 55 Sump 80mm Screen 80mm Riser Pipe 80 x 125 Packer 416.000 410.00 - 408.00 408.00 - 396.00 396.00 - 392.00 392.00 - 391.50
.50 METRE125mm NB SS DRILL-OUT PIPE PLUS X/OVER
6.50 - METRE 80mm RISER PIPE WITH VULCANISED BORE K-PACKER
OTTOM OF 125mm NB CASING FLOAT SHOE AT -396 METRES
12 METRES 80mm NB SS SCREEN FROM 396m TO 408m
CASING FLOAT SHOE
2 METRES SUMP 80mm NB SS WITH END PLATE
TOTAL SCREEN ASY EXTENDS FROM TOP OF PACKER AT 389m TO BASE OF SUMP (BOTTOM OF HOLE) AT - 410m
Replacement Inflatable Packers and Elements Pty Ltd 29 Wheeler St Belmont 6104, Perth Western Australia Tel: (+61 (08) 9475 0700 Fax: +61 (08) 9475 0770 13ackers@ripe - packers.com
www.ripe-packers.com
Australian supplier and manufacturer of well screen PVC rubber k-packers, well packer tri-seals, equipment and services
REPLACEMENT INFLATABLE PACKERS & ELEMENTS PTY LTD

29 WHEELER STREET, BELMONT, WESTERN AUSTRALIA 6104 PH: +61 (08) 9475 0700, Fax: +61 (08) 9475 0770 [email protected] www.ripe-packers.com
Drilling and Construction of New Bores

X X
Suggested General Work Procedure

Drilling Technique: Surface Casing: Main Casing: Screen Assembly: Mud Rotary 273.0m OD steel 125mm NB FRP - 167mm maximum OD at tools joints Stainless Steel drill-out pipe, casing float shoe and cross-over Stainless Steel end plate 2metres 80mm NB stainless steel sump extension 12 metres of 80mm NB, grade 316 stainless steel bore screen 6.50 metres 80mm NB stainless steel riser pipe extension vulcanised bore packer
Bore Construction: Drill for and install 273.10mm OD steel surface casing at ~66metres with a casing float shoe and centralisers and pressure grout it into place. take 2 samples of the grout slurry. Allow 12 hours for grout cure; Top up the annulus with grout to ground level as required; Drill out the shoe and drill a hole of suitable diameter to the target depth which is expected to be approximately 410metres; Stand-by while the contracted operator conducts a geophysical log of the bore; Install 125mm NB FRP casing with casing float shoe, bottom drill-out pipe, crossover and centralisers and pressure grout it into place at the depth directed expected to be at ~ 396metres. Take 2 samples of the grout slurry. (125mm NB FRP casing has a maximum diameter over the tool joints of 167mm); **The decision to grout without the bottom of the hole or to gravel pack the bottom of the hole prior to grouting is entirely at the contractor's discretion.** Allow 24 hours for grout cure; Run in and drill out the cement at the shoe; Continue to clean out the borehole to the depth required for the screen assembly, anticipated to be ~410metres; Run the 80mm NB stainless steel screen assembly and vulcanised bore packer and set it at the depth directed; develop the bore in line with the requirements of the contract; fit the head works assembly standpipe; Cast a concrete block around the standpipe at surface. the block shall be a minimum of 750mm square x 350mm deep. The top of the block shall be at ground level. The top of the standpipe shall be not less than 600mm and not more than 750mm above the top of the block. ** Surface casing depth should be decided on-site as drilling is undertaken.**

Provisional Water Bore Completion

Uploaded by

Copyright:

Available Formats

Provisional Water Bore Completion

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Provisional Water Bore Completion

Uploaded by

Copyright:

Available Formats

REPLACEMENT INFLATABLE PACKERS & ELEMENTS PTY LTD

PROVISIONAL WATER BORE COMPLETION

273.10mm OD STEEL SURFACE CASING PRESSURE GROUTED IN AT - 66 METERS

ENTRALISERS 1 PER CASING LENGTH

.50 METRE125mm NB SS DRILL-OUT PIPE PLUS X/OVER

6.50 - METRE 80mm RISER PIPE WITH VULCANISED BORE K-PACKER

OTTOM OF 125mm NB CASING FLOAT SHOE AT -396 METRES

12 METRES 80mm NB SS SCREEN FROM 396m TO 408m

CASING FLOAT SHOE

2 METRES SUMP 80mm NB SS WITH END PLATE

REPLACEMENT INFLATABLE PACKERS & ELEMENTS PTY LTD

Drilling and Construction of New Bores

Suggested General Work Procedure

You might also like