Thalambur,Chennai-603103 DEPARTMENT OF MECHANICAL ENGINEERING ME 2155 COMPUTER AIDED DRAFTING AND MODELING LABORATORY MANUAL

NAME REG NO. YEAR BRANCH BATCH

: : : : :

INDEX

EX.NO

DATE

EXPERIMENT NAME

MARKS

SIGNATURE

INTRODUCTION TO AUTOCAD DRAWING AND MODIFYING OBJECTS AutoCAD is drafting/modeling software used all over the world by almost all manufacturing companies. It is variable software which can be used in all engineering divisions. It is a drafting version popularly known to everyone associated with mechanical engineering. The AutoCAD drawing enables the designer to communicate his ideas to the outside of department easily. Conversion of AutoCAD files to other software is also using drawing exchange formula. In the lesson, commands and procedures for drawing and modifying the objects are explored. START AND SAVE A DRAWING When you start a drawing, you specify the type of units and other settings you can also choose how to save your files, including saving back up files. The settings you select, English a metric determines default values used for many system variables of controlling text dimensions, grid, snap and default line type and hatch pattern life. ENGLISH - Creates a new drawing based on Imperial Measurement System. The drawing is based on cad.dwt template. METRIC Creates a new drawing based on metric measurement. The drawing is based on ocadiso.dwt template. Save drawing files for later use. CONTROL THE VIEWS You can magnify the details in your drawing for a closer view or shift the view to a different part of the drawing. If you can save the view by name, you can restore them later. UNITS Every object is measured in units. In AutoCAD we can determine the value of the units before we draw. LIMITS The drawing limits are two-dimensional points in the world coordinate that represent a lower-left limit and an upper right limit. You cannot impose limits on the Z direction.

ABSOLUTE COORDINATE SYSTEM In Absolute Coordinate System, the dimensions X and Y of a point is specified with reference to the origin (0, 0). RELATIVE COORDINATE SYSTEM In Relative Coordinate System, the dimensions X and Y of a point are specified with respect to the last entered point (i.e.) the last enter point is taken as origin. POLAR COORDINATE SYSTEM In Polar Coordinate System, the dimensions of a point are specified by using a distance and angle with reference to the previous point. Angles are measured in anticlockwise direction, taking 0 degrees towards right. LINE Line command allows you to create a line where the end points are specified by two dimensional or three dimensional coordinates. POLYLINE PLINE command allows you to draw line and arc segments, but from start to end, it is treated as a sing object. With PLINE command, you can draw objects even with line width. ARC The ARC command allows you to create an arc segment. There are different methods of creating an arc. The different methods of creating an arc are: 1) 3 Points 2) Centre, Start, Radius 3) Start, Centre, End 4) Start, Centre, Angle 5) Start, Centre, Length 6) Start, End, Angle 7) Start, End, Direction 8) Start, End, Radius CIRCLE The CIRCLE command allows you to create a circle. There are four different methods for drawing circles. They are: Centre, Radius/Centre, Diameter 3 Points (3P), 2 Points (2P) Tangent, Tangent, Radius (ttr)

POLYGON Polygon command creates a regular polygon. You must specify the number of sides of the polygon and whether it is Inscribed or Circumscribed polygon. Now, specify the centre and radius of the polygon circle. OSNAP Osnaps allow you to snap onto a specific object location when you are picking a point. For example, using Osnaps you can accurately pick the end point of a line or the center of a circle. ERASE This command is used for deleting unwanted objects. You must select the object to be erased. COPY The copy command is used for making copies of selected objects. The object to be copied must be selected and the base point must be specified and the copy can be dragged and placed at the required position. MOVE This command is used for moving selected objects. The object to be moved must be selected and its base point must be specified then we can drag it to the required location. ROTATE This command is used for rotating selected objects. To rotate an object, first select it and specify a base point. Now enter an angle value or specify a second point to rotate the object. Entering a positive angle value rotates the objects counterclockwise or clockwise, depending on the Direction Contorl Control setting and Drawing Units dialog box. The plane of rotation and the direction of the zero angle depend on the orientation of the user coordinate system. MIRROR The MIRROR command is used for creating mirror images of selected objects. You must first select the object to be mirrored and then specify the axis along which it is mirrored, to create an mirror image of the selected object. This is a very useful command for drawing symmetrical objects about a particular axis.

OFFSET Offset an object to create a new object whose shape parallels the shape of the original object. Offsetting a circle or an arc creates a larger or smaller circle or arc, depending on which side you specify for the offset. POLAR ARRAY This command creates an array of the selected object around a centre point. You must specify the centre point of the array, the total number of items and the angle to fill for creating a polar array. RECTANGULAR ARRAY This command creates an array of the selected objects defined by the number of rows and columns and the offset between them. EXTEND The EXTEND command elongates the selected objects to a specified boundary. TRIM The TRIM command trims off an object using cutting edges defined by other objects. Here the user is required to select object(s) to define cutting edge(s) then select the object to be trimmed; the selected side of the object is removed based on the side of selection of the object to be trimmed relative to the cutting edge. BREAK The BREAK command is used to remove only parts of an object. You must specify the first and second points between which the object must be deleted. FILLET FILLET rounds of the edges of two arcs, circles, elliptical arcs, lines, polylines, rays, splines or xlines with an arc of a specified radius. Rounds along the edges cannot be created with zero radius. CHAMFER CHAMFER command draws a line at the corner between two selected lines. If the lines do not intersect, it extends the lines. If they intersect, the lines extending beyond the chamfer line can be trimmed or left as it is, by the trim mode. LENGTHEN The LENGTHEN command is used to increase/decrease the length of AutoCAD objects.

DIVIDE This command places evenly spaced point objects or blocks along the length or perimeter of an object. You can select only one entity at a time to be divided. The entities that can be selected are: line, arc, circle, polyline and spline. ZOOM ALL This zoom to display the entire drawing in the current viewport. The display shows all the entities even if the drawing extends outside the drawing limits. ZOOM WINDOW ZOOM WINDOW commands to display an area specified by two diagonally opposite corner points of a rectangle window. ZOOM EXTENTS This zoom to display the drawing extents. If the drawings are small in the existing limits, then there is an enlarging effect on the screen. If the drawing occupy the complete area of the limits, then there are many not be much difference between ZOOM ALL and ZOOM EXTENTS. DIMLINEAR This command specifies the linear distance between two selected points. DIMALIGNED This command is used for specifying the linear distance (exact dimensional value) between two points which are inclined at an angle. DIMANGULAR This command is used for obtaining the angle two selected points. The three types are: 1) Arc Selection 2) Circle Selection 3) Line Selection 4) Three Point Selection DIMRADIUS This command gives the value of radius of the specified circle, arc or fillet. A radial dimension consists of a radius dimension line with an arrowhead at the arc or circle end.

DIMCENTER This command marks the centre point of the selected arc or circle. The center mark cannot be updated, so set the required style before executing this command. LINETYPE LINETYPE greatly improves the readability of technical drawings. You can make important features stand out with bold line weights. LAYER Layer is an organizing tool. Layers are like one, where you can keep various types of information. Its always a good idea to keep notes and reference symbols about each element of the drawing as well as drawing dimensions on a new layer. DISTANCE This command lists the distance between the selected points and also lists out the angle in current plane and 3D angle from the current plane, based on the direction of picking the two points. It also lists the projected lengths on the three axes called the delta length. TEXT TEXT command creates text objects with specified height and orientation. Text objects can be created with a variety of character patterns call style. This command allows you to type a single line or multiple lines of text. MTEXT MTEXT creates paragraph that fit within a nonprinting text boundary. The user specified text boundary determines the width of the paragraph and the justification of the text within the paragraph. Each multiline text object is a single object, regardless of the number of lines it contains. HATCH Hatches are shaded pattern which generally represent cross-section of a mechanical component. Using BHATCH command the required area, type of hatch, hatch angle and scale can be specified. PROPERTIES The PROPERTIES command displays the Properties palette. The Properties palette is the main method for viewing and modifying the properties of AutoCAD objects.

VPORTS Viewports are areas that display different views of your model. As you work on the Model tab, you can split the drawing area into one or more adjacent rectangular views known as model space viewports. In large or complex drawings, displaying different views reduces the time needed to zoom or pan in a single view. Also, errors you might miss in one view may be apparent in the others. EXTRUDE Solids can be created by extruding selected objects. Use the EXTRUDE command to create a solid or surface from a common profile of an object REVOLVE REVOLVE command can create a solid or surface by revolving open or closed objects about an axis. The revolved objects define the profile of the solid or surface. PYRAMID This command can create a solid pyramid. The number of sides for a pyramid, from 3 to 32, can be defined. The axis endpoint defines the length and orientation of the pyramid. CREATE LAYOUTS A layout stimulates a sheet of paper and provides a predictable plotting setup for a layout, you can create and position view post objects and you can add a title block or other objects geometry. PLOT DRAWINGS Once you have completed a drawing you can plot the drawing on paper or create a file for use with another application. In either case, you select the plot settings.

TITLE BLOCK

Ex. no: Date: Aim :

TITLE BLOCK WITH NECESSARY TEXT AND PROJECTION SYMBOL

To draw a title block with necessary text and projection symbol on A4 size sheet of 210 X 297 mm using AutoCAD. Software Used: AutoCAD 2011

Commands Used:

Procedure:

Result: Thus the title block with necessary text and projection symbol of a title block on A4 sheet was drawn using AutoCAD.

Ex. no: Date: ABSOLUTE AND RELATIVE COORDINATE SYSTEM

Aim : To study the capabilities of softwares for drafting and modeling coordinate systems. (Absolute & Relative). Software Used : AutoCAD 2011 Commands Used:

Procedure:

Result: The capabilities of software for drafting and modeling were studied and the shapes like square, pentagon and hexagon was drawn using Absolute and Relative coordinate system.

Ex. no:
PLAN OF RESIDENTIAL BUILDING

Date:

Aim: To create the plan of given residential building using Auto CAD software. Software Used: Auto CAD 2008 Commands Used:

Procedure:

Result: The plan of the given residential building is drawn using Auto CAD.

PROJECTIONS AND SECTIONS OF SOLIDS

1.

Draw the projections of a hexagonal prism of base side 20mm and axis

length 50mm when its rests on the ground on one of the edges of the base and the axis inclined at 35o to the ground and parallel to the VP.

2.

A square pyramid of base side 30mm and height 50mm rests on the ground

on one its base edges such that its axis is inclined at 45o to the ground and parallel to VP. Draw its projections.

3.

A Pentagonal prism, side of base 25mm and axis 50mm long, rests with one

of its shorter edges on HP. Such that the base containing that edge makes an angle of 30o to HP, and its axis is parallel to VP. Draw its projections.

Ex. no:
PROJECTION & SECTION OF SIMPLE SOLIDS

Date:

Aim: To draw front and top view of given simple solids (prisms and pyramids) using Auto CAD software. Software Used: Auto CAD 2008 Commands Used:

Procedure:

Result: The front and top views of the given simple solids (prisms and pyramids) are drawn using Auto CAD.

ORTHOGRAPHIC VIEWS OF SOLIDS

Ex. no:
ORTHOGRAPHIC VIEWS OF SOLIDS

Date:

Aim: To draw the orthographic views from the given pictorial views using Auto CAD software. Software Used: Auto CAD 2008 Commands Used:

Procedure:

Result: The orthographic views of the given solids are drawn using Auto CAD.

ISOMETRIC VIEWS OF OBJECTS

Ex. no:
ISOMETRIC VIEWS OF OBJECTS

Date: Aim: To draw the isometric view of given simple solids and objects using Auto CAD software. Software Used: Auto CAD 2008 Commands Used:

Procedure:

Result: The Isometric view of the given simple solids and objects are drawn using Auto CAD.

SIMPLE TRUSSES

Ex. no:
SIMPLE TRUSSES

Date:

Aim: To draw simple trusses using Auto CAD software. Software Used: Auto CAD 2008 Commands Used:

Procedure:

Result: Thus the simple trusses are drawn using Auto CAD.

Ex. no:
2D DRAWING - MACHINE COMPONENTS

Date:

Aim: To draw the given 2d machine components by using Auto CAD.

Software Used: Auto CAD 2008 Commands Used:

Procedure:

Result: Thus the given 2d machine components are drawn and saved.

Ex. no: SPECIAL CURVES Date:

Aim: To create a special curves like B-spline or Cubic spline using Auto CAD software. Software Used: Auto CAD 2008 Commands Used:

Procedure:

Result: The special curves like B-spline or Cubic Spline are drawn using Auto CAD.

POLAR TRACKING METHOD

Ex. no:
POLAR TRACKING METHOD

Date:

Aim: To draw a given diagram using polar tracking method by using Auto CAD. Software Used: Auto CAD 2008 Commands Used:

Procedure:

Result: Thus the given polar tracking diagram drawn and successfully saved.