ANALYSIS OF LIMESTONE INTRODUCTION

Limestone is usually described as rock made from calcium carbonate , CaCO3 , but in fact most limestone rock contains significant amounts of magnesium , silicates, manganese, iron, titanium, aluminum, sodium, potassium, sulphur (as sulphides or sulphates) and phosphorus . In this experiment, you will analyze a sample of limestone to find how much calcium it contains . The reactions you will carry out are as follows . First, the carbonates present are reacted with hydrochloric acid . This procedure releases the calcium and magnesium ions present into solution . Any manganese, iron, titanium, aluminum, sodium, potassium and phosphates present will also go into solution . CaCO3(s) + 2 HCl(aq) MgCO3(s) + 2 HCl(aq)

Ca2+(aq) + CO2(g) + H2O(l) + 2 Cl(aq) Mg2+(aq) + CO2(g) + H2O(l) + 2 Cl(aq)

Some impurities, such as silicates, sulphides and sulphates, remain unreacted and do not go into solution . Adding substantial amounts of both ammonia and ammonium ions to the solution creates a buffer solution which is slightly basic : NH3(aq) + H2O(l)

NH 4 (aq) + OH(aq) .

The resulting buffer solution does not contain sufficient concentrations of OH to precipitate the calcium , magnesium, sodium and potassium ions from solution . However, the concentration of OH is sufficient to precipitate all the iron, manganese, aluminum, titanium and phosphates from solution . For example: Fe3+(aq) + 3 OH(aq) 3 Fe3+(aq) + PO 4

Fe(OH)3(s) FePO4(s)

Filtration at this point completes the removal of everything except the calcium , magnesium, sodium and potassium from the solution . The solution containing the remaining ions is acidified with hydrochloric acid . The addition of oxalate ion , in the form of ammonium oxalate , prepares the solution to precipitate calcium oxalate . However, no precipitate forms because all oxalates are soluble in acidic solutions . By neutralizing the acid with ammonia the resulting solution becomes slightly basic and a precipitate of calcium oxalate monohydrate forms . Since magnesium, sodium and potassium oxalates are soluble in basic solutions , only calcium oxalate precipitates . Ca2+(aq) + C 2 O4 aq) + H2O(l)
2

CaC2O4H2O(s)

PROCEDURE
IMPORTANT: Record all your observations as you work and record all data as required . DAY 1 1. Obtain a sample of limestone rock having a mass of about 2 g . Weigh the sample and record its exact mass. Place the limestone in a 250 mL beaker . Perform steps 2 and 3 in a f me !ood" 2. Obtain 10 mL of 6 M hydrochloric acid (CARE: very corrosive!) . Add the hydrochloric acid to the limestone and, using a hot plate which is pre-heated to medium-low heat , heat for 5 minutes or until the bubble-producing reaction ceases . CARE: If the mixture is almost dry before the bubbling stops , carefully add another 3 mL of 6 M hydrochloric acid to allow the reaction to go to completion . #et t!e fo$$o%in& read' for step 3: a) a single-flask vacuum filtration setup , and b) 50 mL of hot 2 % NH4Cl solution (put this on your hot plate)

Page 2

3. Dilute the contents of the beaker to about 100 mL using distilled water . The remainder of this step can be performed at your bench . Add about 5 g of ammonium chloride to the solution , then heat the solution until it is nearly boiling , then add 10 or 12 drops of methyl red indicator , then add 7 M ammonia, with constant slow stirring , until the solution just turns pale yellow , then boil for 2 minutes, then filter the solution while still hot using a single-flask vacuum filtration apparatus , and finally wash the precipitate with two 25 mL portions of hot 2 % NH 4Cl solution Save the filtered solution in a 400 mL beaker for the next step and discard the precipitate . Turn the hot plate up to high heat, in preparation for step 6. 4. Add another 10 drops of methyl red indicator and then add about 1 mL of 6 M hydrochloric acid to the solution If the solution does not become pink , add another 1 mL of hydrochloric acid . 5. Add 100 mL of 4% ammonium oxalate to the mixture in the beaker . Slowly add, with constant stirring , just enough 2 M ammonia solution (CAUTION: Check the concentration!) to turn the indicators colour from pink to very pale yellow . When the indicator has turned yellow , add an extra 2 mL of 2 M ammonia solution to make the solution sufficiently basic . At this point , a precipitate should be present . 6. Heat the mixture to 90oC, to clump the precipitate into larger particles . CARE: Keep a stirring rod in the beaker and stir frequently to avoid bumping of the mixture . The mixture can be filtered while still hot . 7. Record t!e com(ined mass of TWO filter papers . Then, set up a single-flask vacuum filtration apparatus, making sure to pre-wet the filter papers . 8. Vacuum filter your solution through your pre-weighed filter papers . Wash every bit of the precipitate out of the beaker with three 50 mL portions of 0 .1% ammonium oxalate solution . 9. Label a 250 mL beaker with your name , using a grease pencil, and then record t!e (ea)er*s mass. Carefully remove the filter papers from the filter funnel and place them in the beaker . If any of the precipitate remains on the funnel , scrape as much as possible of the solid into the beaker . Ideally, the precipitate and filter papers should be placed overnight in a drying oven at 110 oC but if a drying oven is not available let the precipitate air-dry overnight . [CARE: Heating the precipitate above 200 oC partially decomposes the CaC 2O4H2O to CaC2O4 and extensive heating decomposes the oxalate to CaCO 3 .]

DAY 2 10. Record the combined mass of the beaker, filter papers and dried precipitate.

CALCULATIONS AND ANALYSIS

2. Calculate the moles of CaC 2O4H2O you produced . 3. Since each molecule of CaC 2O4H2O contains one atom of calcium , the moles of calcium contained in your sample of limestone equals the moles of CaC 2O4H2O produced . Use this fact to calculate the mass of calcium contained in your sample . 4. Use the mass of calcium found in Calculation 3 and your mass of limestone to calculate the percentage of calcium present in your sample . This result is called the ACTUAL PERCENTAGE OF CALCIUM in your sample of limestone . 5. Calculate the percentage composition of CaCO 3. The percentage of Ca found in your percentage composition is the THEORETICAL PERENTAGE OF CALCIUM in pure limestone . 6. Calculate the percentage purity of your limestone sample as follows .

ACTUAL PERCENTAGE OF CALCIUM

% purity =

THEORETICAL PERCENTAGE OF CALCIUM

x 100%