Scribd Logo
Upload

Welcome to Scribd!

  • 81 views

    Hot Dialer Instructions: (Unit # 103-049)

    Uploaded by

    Payphone.com
    The Hot Dialer automatically dials a stored number when an attached phone is picked up. To set it up, splice the phone line wires to the terminal screws on the circuit board. The personal code can be changed by dialing 1022 followed by a new 4-digit code. To program the number to dial, enter 10 plus the personal code and then 1034 followed by the number with any required area code or 1. The stored number can be erased by entering 10 plus the personal code and then 1021.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    Hot Dialer Instructions: (Unit # 103-049)

    Uploaded by

    Payphone.com
    81 views1 page
    The Hot Dialer automatically dials a stored number when an attached phone is picked up. To set it up, splice the phone line wires to the terminal screws on the circuit board. The personal code can be changed by dialing 1022 followed by a new 4-digit code. To program the number to dial, enter 10 plus the personal code and then 1034 followed by the number with any required area code or 1. The stored number can be erased by entering 10 plus the personal code and then 1021.

    Original Title

    HotDialer

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The Hot Dialer automatically dials a stored number when an attached phone is picked up. To set it up, splice the phone line wires to the terminal screws on the circuit board. The personal code can be changed by dialing 1022 followed by a new 4-digit code. To program the number to dial, enter 10 plus the personal code and then 1034 followed by the number with any required area code or 1. The stored number can be erased by entering 10 plus the personal code and then 1021.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    81 views1 page

    Hot Dialer Instructions: (Unit # 103-049)

    Uploaded by

    Payphone.com
    The Hot Dialer automatically dials a stored number when an attached phone is picked up. To set it up, splice the phone line wires to the terminal screws on the circuit board. The personal code can be changed by dialing 1022 followed by a new 4-digit code. To program the number to dial, enter 10 plus the personal code and then 1034 followed by the number with any required area code or 1. The stored number can be erased by entering 10 plus the personal code and then 1021.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    Hot Dialer Instructions

    (Unit # 103-049)

    The Hot Dialer will automatically pulse dial to a stored number when the telephone connected to it is taken off-
    hook. The information below outlines the steps to connect the telephone line to the Hot Dialer and gives
    instructions on how to program the number it is to dial to.

    Connecting the Telephone Line to the Hot Dialer


    1. Locate the two terminal screws on the Hot Dialer’s circuit board and slightly
    loosen each screw, (if the unit is a surface mount, you will need to open the top
    cover in order to get to the circuit board.)
    2. Locate the telephone wire pair for the telephone line being used and carefully
    splice the outer coating of each wire so that approx. ½” of copper wire is exposed.
    3. Connect each wire from the telephone wire pair to each terminal screw by
    wrapping the exposed copper section around the terminal screw and then tightening
    the screw.

    To Change your 4-Digit Personal Code:


    1. Connect a regular telephone to the Hot Dialer.
    2. Within two seconds of taking the telephone off-hook, dial 10 2222 (factory preset
    personal code), wait for a dial tone.
    3. Dial 1040, wait for a dial tone.
    4. Enter any 4-digit personal code of your choice.
    5. Wait for a ‘beep’ to verify the entry was taken, then hang up.
    • We strongly recommend that you WRITE DOWN YOUR PERSONAL CODE & keep it in a safe place. The
    only way to recover from a lost personal code is to return your Data Port Dialer to the factory for a complete
    reset.
    4-Digit Personal Code___________________________________________

    To Program the Hot Dialer’s outpulse Number:


    1. Connect a regular telephone to the Hot Dialer.
    2. Within two seconds of taking the telephone off-hook, dial 10 + your 4-digit personal code, wait for a dial tone.
    3. Dial 1034, wait for a dial tone.
    4. Enter the number you want the Hot Dialer to dial to as you would normally dial it, followed by the # key. This
    number will be called every time the telephone connected to it is taken off-hook.
    • If a 1 and / or the area code is required when calling the number from the location of the Hot Dialer, make sure
    you include the 1 and / or the area code before the number.

    To Erase the the Hot Dialer’s outpulse Number:


    1. Connect a regular telephone to the Hot Dialer.
    2. Within two seconds of taking the telephone off-hook, dial 10 + your 4-digit personal code, wait for a dial tone.
    3. Dial 1021, wait for a confirmation tone and a new dial tone.
    4. Hang up the phone. The old number is now erased. The Hot Dialer is now ready to receive a new number to
    dial.

    You might also like