Scribd
Upload
105 views

3.044 Problem Set 1: Heat Conduction Due Monday February 14, 2005

This document provides instructions and questions for a heat conduction problem set. It includes questions about selecting optimal materials for heat conduction/resistance applications, calculating heat loss through a layered furnace wall using British units, analyzing temperature changes in a titanium rod undergoing Joule heating, and modeling heat transfer during resistance welding of aluminum rods. The problem set requires using concepts of heat conduction, thermal properties of materials, and the heat equation to solve applied problems.

Uploaded by

Carlos Castillo
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
105 views

3.044 Problem Set 1: Heat Conduction Due Monday February 14, 2005

This document provides instructions and questions for a heat conduction problem set. It includes questions about selecting optimal materials for heat conduction/resistance applications, calculating heat loss through a layered furnace wall using British units, analyzing temperature changes in a titanium rod undergoing Joule heating, and modeling heat transfer during resistance welding of aluminum rods. The problem set requires using concepts of heat conduction, thermal properties of materials, and the heat equation to solve applied problems.

Uploaded by

Carlos Castillo
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

3.

044 Problem Set 1


Heat Conduction Due Monday February 14, 2005
1. Thermal properties and optimal materials selection (30 pts, 5 each) In many situations, product designs include parts whose only function is to conduct or resist the conduction of heat. Materials for these parts are thus chosen entirely on the basis of their thermal properties. Select the best material for each of the following applications using the MatML Grapher software at http://orbis.kent.edu/matdl/matml/select.php supplemented with the extra candidate materials below. (Select the conductivity/thermal density graph to make things easier.) (a) Heat shield sandwiched between a hot body and a cold one which minimizes the steady ux between them. (b) Heat shield which protects something from short, intense bursts of heat (long timescale is needed). (c) Cheap (i.e. not diamond) temperature sensor, in which short timescale of heat conduction is necessary for rapid response. (d) Light heat reservoir which must hold as much heat as possible per degree C per unit weight. (e) Heat sink for a semiconductor device, which must minimize temperature dierence for a given ux. (f) Heat sink for melt spinning, in which liquid metal is injected against a rotating heat sink where it is solidied as rapidly as possible, so the material must conduct heat away from the surface quickly. (Hint: evaluate the ux through x = 0 in an erfc-like unsteady conduction problem. Diamond is not an ecomonically viable option.) Extra candidate materials: Material gold silver diamond graphite lime (CaO) alumina (Al2 O3 )
W k, m K 315.5 425 2320 63 15.5 39 g , cm 3 19.3 10.5 3.5 2.25 3.32 3.96

cp , kgJ K 130 234 519 711 749 804

For those interested: Ashbys appendix has a plot similar to that in the MatML Grapher, but with k vs. (which they call vs a). Which format do you consider more visually helpful: that, or the Graphers k vs. cp ? For more exible materials selection, try: http://orbis.kent.edu/matdl/matml/select_other.php

2. Layered furnace wall and British units (20 pts) A cylindrical furnace wall consists of an inner graphite layer 18 inches (1.5 feet) thick, followed by an outer layer of insulating brick four feet thick, both surrounding a cylindrical container 15 feet high (on the inside) with an inner diameter of 20 feet containing molten metal. Data: Outer brick-environment heat transfer coecient: 4 BTU/hrft2 F Brick thermal conductivity: 16 BTU/hrft F Graphite thermal conductivity: 63
W m K

times 0.557

mK BTU W hrft F

Inner graphite-liquid metal heat transfer coecient: very large (assume innite) (a) Calculate the total heat loss in BTU/hr from molten metal at 2000 F to an environment at 70 F. (You may neglect the corners of the cylinder, but include the top and bottom.) (8) (b) How would your solution to part 2a would change if you include heat conduction in the corners? (I.e. is your answer an overestimate or underestimate?) (4) (c) Calculate the temperature at each of the interfaces in the radial direction. (8) 1 BTU (British Thermal Unit) of heat raises the temperature of 1 pound of water by 1 F. 3. Joule heating of a titanium rod (25 pts)

At time t = 0, the temperature in a titanium rod 0.25 cm (2.5 103 m) in diameter is uniform and equal to its surface temperature. A switch is turned on so that a current passes lengthwise through the rod, heating it through a mechanism known as Joule heating. Assume the current is uniformly distributed throughout the rod, so it is heated uniformly, with a uniform heat generation rate per unit volume q . Titanium data:
W Thermal conductivity: k = 20 m K kg Density: = 4700 m 3

Heat capacity: cp = 700 kgJ K


W (a) At a current of 10 amperes, the heat generation rate per unit volume q is approximately 5 106 m 3. Use the uniform-generation solution to the heat conduction equation to calculate the maximum temperature dierence between the center of the rod and its surface. (8)

(b) If the current through the rod doubles to 20 amps, the heat generation rate q quadruples. How does this aect the dierence between the maximum temperature in the center and the temperature at the surface? (4) (c) Assuming the surface is held at a constant temperature, sketch the temperature T as a function of r across the rod for several dierent times t. (This should have one curve for t = 0, one for the steady-state at t = , and others for several intermediate times.) (8) (d) Approximately how long will it take for the center of the rod to reach its maximum temperature? (5)

4. Heat Transfer in Resistance Welding (25 pts) In resistance welding, two pieces of metal are held against each other, and a very high voltage is applied between them for a very short time. The highest resistance in the circuit is at the interface, so heat concentrates there, melting the metal and joining the two pieces together. Two cylindrical aluminum rods are joined end-to-end in this way. You would like to know the temperature prole as a function of time T (x, t) to assess the width of the heat-aected zone (region with signicant microstructure change due to heating).

Aluminum data:
W Thermal conductivity: k = 238 m K kg g Density: = 2700 m 3 (= 2.7 cm3 )

Heat capacity: cp = 917 kgJ K (a) Let t = 0 at the moment immediately after the very brief application of current (i.e. at t = 0 the current is turned o). Sketch the temperature distribution at several times starting at t = 0. (7) (b) Assuming there is no heat loss from the sides of the rod, write the heat conduction equation solution which describes the temperature distribution at moderate to long time scales (while the rod length can still be considered innite). (4) (c) At t = 0, the whole rod is at 40 C due to Joule heating by the current. Another 3 106 J/m2 of Joule heating energy has been deposited right at the junction to make the weld. Calculate the maximum temperature at t = 1 seconds and t = 10 seconds. (Hint in applying this solution: consider the relationship between energy or enthalpy and temperature.) (7) (d) Also at t = 1 seconds, what is the width of the region where the temperature dierence T 40 C is at least half of its maximum value? What is that width at t = 10 seconds? (7)

You might also like