Scarab Magnum Unidrive

The Scarab Unidrive System

Maintaining Scarab’s well-proven and successful Single-Engine philosophy, Scarab’s Magnum
Unidrive utilises PTO-driven pumps to operate all hydraulic sweeper functions, while retaining the
conventional chassis transmission, to produce a heavy-duty truck-mounted road sweeper that
embodies all the advantages that Scarab users have come to expect as standard issue.
Designed to cope with the most arduous of operating conditions, the Scarab System provides
the operator with a machine offering the LARGEST PAYLOAD and LARGEST HOPPER VOLUME
commensurate with a given chassis size and type, together with a minimum of moving parts for
reduced servicing. By utilising the chassis engine, which conforms to the latest stringent emission
legislation, significant REDUCTIONS in EXHAUST EMISSIONS and FUEL CONSUMPTION, can be
achieved, making the Scarab Magnum Unidrive one of the most environmentally friendly, high
performance truck-mounted road sweepers.

Scarab Magnum Unidrive Sweeper

Increased hopper
WATER
PAYLOAD Increased payload
Simplified drive system
Reduced servicing and operating costs
Reduced fuel consumption
Reduced environmental impact

Typical Twin Engine Sweeper

Restricted hopper
PAYLOAD
Restricted payload
Complex engine drive system WATER
Higher operating costs
Higher fuel consumption
Reduced road-speed control
AUXILIARY ENGINE

1
SCARAB UNIDRIVE: Utilising the manual transmission of the chassis the Scarab Magnum
Unidrive allows the driver to sweep at a wide range of sweeping speeds, dependent on
sweeping conditions. Typical sweeping speeds range from 1.6 mph (2.6 m/h) upwards. A
robust engine driven PTO supplies the power for suction fan and brushes.
Reduction Gearbox
For 6 speed chassis the Scarab pneumatically operated reduction gearbox is fitted to
provide the required sweep speed range (from 0.8 mph/1.1 km/h). This is controlled from the
main CANbus panel via motion sensors to prevent engagement when the vehicle is moving.
SUCTION FAN:. The suction fan is mounted on the hopper top, driven by a direct drive axial
piston hydraulic motor with a normal operating speed of 2000 RPM. The dynamically
balanced 900 mm diameter fan is a very efficient multi-blade centrifugal unit, giving a
nominal airflow of 6000 ft3/min (170 m3/min). Mounting the fan on the hopper top creates a
virtually straight and highly efficient airflow from suction nozzle to fan, significantly reducing
power requirements. There are two operating modes, standard for normal sweeping and
boost, to increase suction power for very arduous conditions. When the optional overhead
boom is fitted an additional boost speed is provided for even greater suction performance.
SUCTION NOZZLE: Of all-steel construction, the 740 mm wide suction nozzle is mounted in a
trailed frame running on 250 mm diameter rubber tyred wheels. A 250 mm diameter suction
hose connects the nozzle to the hopper. Easily replaced adjustable rubber flaps and a skid
plate are used to form the nozzle inlet and the high suction performance makes feasible a
flap to ground clearance of 25–30 mm resulting in a long flap life and less need for
adjustment. Four manually adjustable water spray jets are fitted to the nozzle at 90° intervals
to provide an internal dust suppression spray. Additional water injection nozzles are available
when required. An optional 4-jet water boost bar can also be fitted in front of suction nozzle
for use in extreme conditions. A tilting mechanism enables the nozzle to accommodate
large objects or autumn leaf build-ups with ease.
SIDE BRUSH: 650 mm diameter steel-tined quick-change brush with direct drive hydraulic
motor, fitted with trailed linkage, kick back protection, pneumatic ram for in/out control, fully
adjustable for brush angle, three speed control (nominally 100 / 125 / 150 RPM). Optional
brush pressure control is also available. A work light is fitted to assist with low light operation.
WIDE SWEEP: 320 mm diameter quick-change polypropylene segments with direct drive
hydraulic motor, fully floating with shock absorbers to prevent bounce, fitted with trailed
linkage to ensure parallel, even brush wear. Three speed control (nominally 200 / 250 / 300
RPM). Optional brush pressure control is available if required.
HOPPER: 7.2 m3 Gross Hopper Volume* offering a 6.5 m3 Hopper Payload Volume*. Constructed
entirely from corrosion and abrasion resistant stainless steel, the hopper is fitted with large
access doors on either side and a reinforced rear door with heavy-duty seals. The rear door
incorporates an automatic closure system which clamps the door at 3 points, for a
watertight seal, and body-drain facility for removal of excess water.
All inlet tubes are fitted with automatic blanking flaps and an easy-to-clean swing-down filter
screen is mounted in the top of the hopper immediately below the suction fan. A storage
compartment is provided, located on right hand side of the body.
The hopper is tipped by means of a two-stage tipping ram facilitating rapid load discharge.
* Scarab hopper capacities are calculated in accordance with European Standard EN15429
HYDRAULIC SYSTEM: PTO driven pumps deliver the hydraulic power. The first, an axial piston
pump with automatic control of output and pressure, drives the suction fan. It is controlled
by an electric valve, which adjusts the output to provide normal and boost suction fan
speeds. The second, a gear pump**, provides power to brush motors and hydraulic rams.
The hydraulic system is piped in zinc plated steel tubing, where practical, and is protected
by 10-micron filters to ensure long component-life. The system’s oil is cooled via a heat
exchanger with hydraulically driven high-performance fan, ensuring optimum cooling under
the most arduous working conditions and/or high ambient temperatures. The hydraulic
control valves are located for easy servicing in a protected compartment, all services being
operated from the cab mounted control consoles.
** An additional gear pump is added when required, according to need, with optional equipment fits

2
WATER PUMP: A self-priming pump fitted with suction filter and driven by a direct-drive
hydraulic motor. Solenoid valves operated from the CANbus control panel direct water
supply to the brushes and suction nozzles. Output is rated at 36 litres/minute @ 50 psi (3.5 bar).
WANDER HOSE: A lightweight flexible suction hose (4 m long x 150 mm diameter), complete
with aluminium extension tube and adjustable handle for cleaning awkward areas or gullies.
Quick release wander hose points are located at either side of the rear door. The hose can
be used while sweeping or on its own for more powerful suction. Optional overhead or rear-
mounted booms with aluminium or steel gully entry tube can be fitted if required.
HYDRAULIC TANK: Located adjacent to the oil cooler, 15 litre capacity, with 10 micron return
filter, air breather, suction strainer, and sight glass with automatic low-level shut off.
PNEUMATIC SYSTEM: The pneumatic system is connected to the vehicle auxiliary air supply,
and is fitted with a pressure regulator, filter / water separator and pneumatic solenoid valves
to control the side brush, wide sweep brush, suction nozzle, and gear change. The
pneumatic valves are located for easy servicing in a protected compartment.
CANbus2 CONTROL: Scarab’s tried and tested CANbus system, in service since 2003 has
proved to be a successful and welcome innovation. CANbus2 has been developed to take
advantage of the latest chassis technology giving even greater control. A compact panel
adjacent to the driver’s seat contains all controls for operating the main sweeper functions.
The panel also displays relevant operating data and provides system diagnostics and a fault-
finding facility. An additional satellite control panel, for frequently used operations is
mounted conveniently to hand.
WATER TANK: 1800 litre gross capacity manufactured from corrosion resistant glass reinforced
plastic and fitted with a large lid, to facilitate cleaning, a sight glass with level indicator and
suction strainers. Filling is by means of a hydrant connector with regulation air break, or
alternatively through an optional hose pipe attachment.
PAINTING: Two pack system single colour, optional multi colour and sign-writing.
TYPICAL SWEEPING WIDTHS:

SUCTION
NOZZLE The suction nozzle, side brush and wide
740
ONLY sweep brush can be raised or lowered
independently of each other. This
provides various sweeping patterns to
suit differing road conditions.
SUCTION NOZZLE
& SIDE BRUSH
1135

SUCTION NOZZLE,
SIDE BRUSH
& WIDESWEEP
2075

BOTH NOZZLES, On dual sweep machines the Scarab

BOTH SIDE BRUSHES Magnum has the option of operating
& WIDESWEEP with both side brushes and nozzles
3200
simultaneously to give an unrivalled
sweeping width.

CHASSIS SUITABILITY:
The Scarab Magnum Unidrive can be mounted on a wide range of chassis.
OPTIONS:.
A comprehensive range of options is available for the Scarab Magnum, please contact the
Scarab Sales Department for further information.

3
TYPICAL WEIGHT DATA:
SINGLE SWEEP CONFIGURATION DUAL SWEEP CONFIGURATION
Scarab Equipment Weight 2550 kg Scarab Equipment Weight 2750 kg
Typical DAF FA LF 55-180** 4235 kg* Typical DAF FA LF 55-180 4235 kg*
15 tonne - 6 speed chassis 15 tonne - 6 speed chassis
Typical DAF FA LF 55-220 4265 kg Typical DAF FA LF 55-220** 4265 kg
15 tonne - 9 speed chassis 15 tonne - 9 speed chassis
Typical Iveco Tector ML 140E** 4454 kg* Typical Iveco Tector ML 140E 4454 kg*
18K 14 tonne - 6 speed chassis 18K 14 tonne - 6 speed chassis
Typical Iveco Tector ML 150E 4340 kg* Typical Iveco Tector ML 150E 4340 kg*
22K 15 tonne - 9 speed chassis 22K 15 tonne - 9 speed chassis
Typical Mercedes 1318K** 4202 kg* Typical Mercedes 1318K 4202 kg*
13.5 tonne - 6 speed 13.3 tonne - 6 speed
Typical Mercedes 1318K** 4252 kg* Typical Mercedes 1318K** 4252 kg*
13.5 tonne - 9 speed 13.5 tonne - 9 speed
Single sweep configuration includes fixed widesweep. Dual Sweep configuration includes swivelling widesweep
* Weights quoted were correct at time of publication and are subject to specification and manufacturers’ tolerances
** Six-speed chassis are fitted with the Scarab reduction gearbox which is installed to provide the desired range of sweeping-
speeds. For details of suitable chassis specifications please contact the Sales Department.

TYPICAL PAYLOAD BASED ON A DAF 15 TONNE x 6-SPEED CHASSIS

EQUIPMENT SPECIFICATION PAYLOAD*
Single Sweep (including Wander Hose and Fixed Widesweep Brush) 8215 kg
Dual Sweep (inc. Wander Hose, Swivelling Widesweep & H-P Water Pump 7965 kg

TYPICAL DIMENSIONAL DATA:

The following dimensional information is indicative only. For specific chassis related
information please make contact with our Sales Department.

Length Overall A 6040 mm

Height Overall B 3130 mm

C
Max Height (Hopper Up) C 4840 mm
B Dimensions given are for general guidance only and
are subject to chassis type used.

Scarab Sweepers are dedicated to continuous product development and as such

we reserve the right to change this specification without prior notice.
To ensure latest information contact Sales Department.

Pattenden Lane, Marden, Tonbridge, Kent. TN12 9QD

Telephone: 01622 831006
Fax: 01622 832417
E-Mail: [email protected]
Web Site: www.scarab-sweepers.com
Publication Z036420 Issue - November 2009 / E & OE