multiSIM 8

Simulation & Capture

Component Reference
Guide
Multisim and Electronics Workbench
copyright  1989, 1992-2004 Interactive Image Technologies Ltd. All rights reserved.
All other brand or product names are trademarks or registered trademarks of their respective companies or
organizations.

MSM8-E-1789 Rev. 1
 2004 Interactive Image Technologies Ltd. All rights reserved. Published December 2004.
Printed in Canada.
Component Reference Guide
This guide contains information on the components found in Multisim 8.
The chapters in the Component Reference Guide are organized to follow the component
groups that are found in the Multisim 8 databases.

License Agreement
Please read the license agreement included in the User Guide carefully before installing and
using the software contained in this package. By installing and using the software, you are
agreeing to be bound by the terms of this license. If you do not agree to the terms of this
license, simply return the unused software within ten days to the place where you obtained it
and your money will be refunded.
Table of Contents
1. Source Components
1.1 Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1.1.1 About Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1.1.2 The Ground Component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1.2 Digital Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1.3 DC Voltage Source (Battery) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1.3.1 Battery Background Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1.3.2 Battery Component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1.4 VCC Voltage Source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1.5 DC Current Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
1.6 AC Voltage Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
1.7 AC Current Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
1.8 Clock Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
1.9 Amplitude Modulation (AM) Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
1.9.1 Characteristic Equation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
1.10 FM Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
1.10.1 FM Voltage Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
1.10.2 Characteristic Equation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
1.10.3 FM Current Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
1.10.4 Characteristic Equation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
1.11 FSK Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
1.12 Voltage-Controlled Voltage Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
1.13 Current-Controlled Voltage Source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
1.14 Voltage-Controlled Current Source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
1.15 Current-Controlled Current Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
1.16 Voltage-Controlled Sine Wave . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
1.16.1 The Component. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
1.16.2 Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11

Multisim 8 Component Reference Guide i

 1.17 Voltage-Controlled Square Wave . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-13
1.17.1 The Component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-13
1.17.2 Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-13
1.18 Voltage-Controlled Triangle Wave. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-15
1.18.1 The Component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-15
1.18.2 Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-15
1.19 Voltage-Controlled Piecewise Linear Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-16
1.20 Voltage Controlled Resistor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-17
1.21 Piecewise Linear Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-18
1.21.1 The Component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-18
1.21.1.1 Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-18
1.21.1.2 Input Text File Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-19
1.21.1.3 Special Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-20
1.21.2 Piecewise Linear Voltage Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-21
1.21.3 Piecewise Linear Current Source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-21
1.22 Pulse Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-21
1.22.1 Pulse Voltage Source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-22
1.22.2 Pulse Current Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-23
1.23 Polynomial Source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-23
1.23.1 Output Voltage Characteristic Equation . . . . . . . . . . . . . . . . . . . . . . . . . .1-24
1.24 Exponential Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-24
1.24.1 Exponential Voltage Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-25
1.24.2 Exponential Current Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-26
1.25 Nonlinear Dependent Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-26
1.26 Controlled One-Shot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-27
1.27 Magnetic Flux Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-28
1.28 Magnetic Flux Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-28
1.29 Multiplier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-29
1.29.1 Characteristic Equation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-31
1.29.2 Multiplier Parameters and Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-31
1.30 Divider . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-31
1.30.1 Characteristic Equation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-33
1.30.2 Divider Parameters and Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-33

ii Electronics Workbench
 1.31 Transfer Function Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-34
1.31.1 Characteristic Equation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-34
1.31.2 Transfer Function Block Parameters and Defaults . . . . . . . . . . . . . . . . . . 1-35
1.32 Voltage Gain Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-36
1.32.1 Characteristic Equation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-37
1.32.2 Voltage Gain Block Parameters and Defaults . . . . . . . . . . . . . . . . . . . . . . 1-37
1.33 Voltage Differentiator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-38
1.33.1 Investigations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-38
1.33.1.1 Sine wave . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-38
1.33.1.2 Triangle waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-38
1.33.1.3 Square waves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-39
1.33.2 Characteristic Equation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-40
1.33.3 Voltage Differentiator Parameters and Defaults . . . . . . . . . . . . . . . . . . . . 1-40
1.34 Voltage Integrator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-40
1.34.1 Investigations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-41
1.34.2 Characteristic Equation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-41
1.34.3 Voltage Integrator Parameters and Defaults . . . . . . . . . . . . . . . . . . . . . . . 1-42
1.35 Voltage Hysteresis Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-42
1.35.1 Hysteresis Block Parameters and Defaults . . . . . . . . . . . . . . . . . . . . . . . . 1-43
1.36 Voltage Limiter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-44
1.36.1 Characteristic Equation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-45
1.36.2 Voltage Limiter Parameters and Defaults . . . . . . . . . . . . . . . . . . . . . . . . . 1-45
1.37 Current Limiter Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-45
1.37.1 Current Limiter Parameters and Defaults . . . . . . . . . . . . . . . . . . . . . . . . . 1-47
1.38 Voltage-Controlled Limiter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-48
1.38.1 Voltage-Controlled Limiter Parameters and Defaults . . . . . . . . . . . . . . . . 1-49
1.39 Voltage Slew Rate Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-50
1.39.1 Voltage Slew Rate Block Parameters and Defaults . . . . . . . . . . . . . . . . . 1-51
1.40 Three-Way Voltage Summer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-52
1.40.1 Charactistic Equation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-53
1.40.2 Summer Parameters and Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-54
1.41 Three Phase Delta . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-54
1.42 Three Phase Wye . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-54
1.43 Thermal Noise Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-55

Multisim 8 Component Reference Guide iii

2. Basic Components
2.1 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
2.2 Rated Virtual Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
2.3 Sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
2.4 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
2.5 Resistor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
2.5.1 Resistor: Background Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4
2.5.2 About Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4
2.5.3 Characteristic Equation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4
2.5.4 Resistor Virtual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5
2.6 Capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5
2.6.1 Capacitor: Background Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6
2.6.2 Characteristic Equation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6
2.6.3 DC Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6
2.6.3.1 Time-Domain Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6
2.6.4 AC Frequency Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-7
2.6.5 Capacitor Virtual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8
2.7 Inductor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8
2.7.1 Inductor: Background Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8
2.7.2 Characteristic Equation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9
2.7.3 DC Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9
2.7.4 Time-Domain Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9
2.7.5 AC Frequency Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-10
2.7.6 Inductor Virtual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-10
2.8 Transformer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-11
2.8.1 Characteristic Equation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-11
2.8.2 Ideal Transformer Model Parameters and Defaults . . . . . . . . . . . . . . . . . .2-12
2.9 Nonlinear Transformer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-12
2.9.1 Customizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-12
2.9.2 Nonlinear Transformer Parameters and Defaults . . . . . . . . . . . . . . . . . . .2-13
2.10 Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-14
2.10.1 Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-14
2.10.2 Characteristic Equation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-15
2.11 Variable Capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-15
2.11.1 The Component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-15
2.11.2 Characteristic Equation and Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-16

iv Electronics Workbench
 2.11.3 Virtual Variable Capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
2.12 Variable Inductor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
2.12.1 The Component. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
2.12.2 Characteristic Equation and Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
2.12.3 Virtual Variable Inductor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17
2.13 Potentiometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17
2.13.1 The Component. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17
2.13.2 Characteristic Equation and Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
2.13.3 Virtual Potentiometer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
2.14 Pullup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
2.15 Resistor Packs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
2.16 Magnetic Core . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19
2.16.1 Characteristic Equation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19
2.16.2 Magnetic Core Parameters and Defaults . . . . . . . . . . . . . . . . . . . . . . . . . 2-20
2.17 Coreless Coil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20
2.17.1 Characteristic Equation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21
2.17.2 Coreless Coil Parameters and Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21
2.18 Z Loads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21
2.18.1 A+jB Block. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21
2.18.2 A-jB Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22
2.18.3 Z Load 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22
2.18.4 Z Load 1 Delta. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22
2.18.5 Z Load 1 Wye . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
2.18.6 Z Load 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
2.18.7 Z Load 2 Delta. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
2.18.8 Z Load 2 Wye . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24
2.18.9 Z Load 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24

3. Diodes
3.1 Diode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1.1 Diodes: Background Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1.2 DC Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.1.3 Time-Domain Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3.1.4 AC Small-Signal Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
3.1.5 Diode Parameters and Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Multisim 8 Component Reference Guide v

 3.2 Pin Diode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5
3.2.1 Photo Diode Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6
3.3 Zener Diode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6
3.3.1 DC Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6
3.3.2 Zener Diode Parameters and Defaults. . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7
3.4 LED (Light-Emitting Diode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-8
3.4.1 Background Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-9
3.4.2 LED Parameters and Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-9
3.5 Full-Wave Bridge Rectifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-10
3.5.1 Characteristic Equation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-10
3.5.2 Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-10
3.5.3 Full-Wave Bridge Rectifier Parameters and Defaults. . . . . . . . . . . . . . . . .3-11
3.6 Schottky Diode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12
3.7 Silicon-Controlled Rectifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12
3.7.1 Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13
3.7.2 Time-Domain Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13
3.7.3 AC Small-Signal Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-14
3.7.4 SCR Parameters and Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-14
3.8 DIAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-14
3.8.1 DC Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-15
3.8.2 Time-Domain and AC Small-Signal Models . . . . . . . . . . . . . . . . . . . . . . . .3-15
3.8.3 DIAC Parameters and Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-16
3.9 TRIAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-16
3.9.1 Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-16
3.10 Varactor Diode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-18

4. Transistors
4.1 BJT (NPN & PNP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
4.1.1 Characteristic Equations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
4.1.2 Time-Domain Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4
4.1.3 AC Small-Signal Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5
4.1.4 BJT Model Parameters and Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6
4.2 Resistor Biased BJT (NPN & PNP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-8
4.3 Darlington Transistor (NPN & PNP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-8
4.3.1 DC Bias Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-9

vi Electronics Workbench
 4.3.2 AC Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
4.3.2.1 AC Input Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
4.3.2.2 AC Current Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
4.4 BJT Array . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
4.4.1 General-purpose PNP Transistor Array . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
4.4.2 NPN/PNP Transistor Array . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
4.4.3 General-purpose High-current NPN Transistor Array . . . . . . . . . . . . . . . . 4-11
4.5 P-Channel MOSFET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
4.6 N-Channel MOSFET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
4.7 MOSFET. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
4.7.1 Depletion MOSFETs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
4.7.2 Enhancement MOSFETs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
4.7.3 DC Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
4.7.4 Time-Domain Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
4.7.5 AC Small-Signal Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
4.7.6 MOSFET Level 1 Model Parameters and Defaults . . . . . . . . . . . . . . . . . . 4-15
4.8 MOSFET Thermal Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
4.9 JFETs (Junction FETs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18
4.9.1 DC Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18
4.9.2 JFET Model Parameters and Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20
4.10 Power MOSFET (N/P) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21
4.11 Power MOSFET Complementary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21
4.12 N-Channel & P-Channel GaAsFET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21
4.12.1 Model and Characteristic Equations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22
4.12.2 GaAsFET Parameters and Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23
4.13 IGBT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23
4.14 Unijunction Transistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24

5. Analog Components
5.1 Opamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.1.1 Opamp Model Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.1.2 Ideal Opamp Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.1.3 Opamp: Background Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5.1.4 Opamp: Simulation Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
5.1.4.1 L1 Simulation Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

Multisim 8 Component Reference Guide vii

 5.1.4.2 L2 Simulation Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-5
5.1.4.3 L3 Simulation Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-8
5.1.4.4 L4 Simulation Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-8
5.2 Norton Opamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-8
5.2.1 The Component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-8
5.2.2 Norton Opamp: Simulation models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-8
5.3 Comparator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-9
5.3.1 The Component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-9
5.3.2 Comparator: Simulation models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-10
5.3.3 Comparator Parameters and Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-11
5.4 Wide Band Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-11
5.4.1 The Component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-12
5.4.2 Wide Band Amplifier: Simulation models . . . . . . . . . . . . . . . . . . . . . . . . . .5-12
5.5 Special Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-12
5.5.1 The Component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-12
5.5.2 Special Function: Simulation models . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-13

6. TTL
6.1 Standard TTL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
6.2 Schottky TTL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
6.3 Low-Power Schottky TTL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
6.4 74xx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
6.4.1 74xx00 (Quad 2-In NAND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
6.4.2 74xx01 (Quad 2-In NAND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-3
6.4.3 74xx02 (Quad 2-In NOR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-3
6.4.4 74xx03 (Quad 2-In NAND (Ls-OC)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-3
6.4.5 74xx04 (Hex INVERTER). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-4
6.4.6 74xx05 (Hex INVERTER (OC)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-4
6.4.7 74xx06 (Hex INVERTER (OC)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-5
6.4.8 74xx07 (Hex BUFFER (OC)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-5
6.4.9 74xx08 (Quad 2-In AND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-5
6.4.10 74xx09 (Quad 2-In AND (OC)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-6
6.4.11 74xx10 (Tri 3-In NAND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-6
6.4.12 74xx100 (8-Bit Bist Latch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-7
6.4.13 74xx107 (Dual JK FF(clr)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-7
6.4.14 74xx109 (Dual JK FF (+edge, pre, clr)) . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-8
6.4.15 74xx11 (Tri 3-In AND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-8

viii Electronics Workbench

 6.4.16 74xx112 (Dual JK FF(-edge, pre, clr)). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
6.4.17 74xx113 (Dual JK MS-SLV FF (-edge, pre)) . . . . . . . . . . . . . . . . . . . . . . . 6-10
6.4.18 74xx114 (Dual JK FF (-edge, pre, com clk & clr)) . . . . . . . . . . . . . . . . . . . 6-10
6.4.19 74xx116 (Dual 4-bit latches (clr)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
6.4.20 74xx12 (Tri 3-In NAND (OC)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
6.4.21 74xx125 (Quad bus BUFFER w/3-state Out) . . . . . . . . . . . . . . . . . . . . . . 6-12
6.4.22 74xx126 (Quad bus BUFFER w/3-state Out) . . . . . . . . . . . . . . . . . . . . . . 6-12
6.4.23 74xx13 (Dual 4-In NAND (Schmitt)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
6.4.24 74xx132 (Quad 2-In NAND (Schmitt)). . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13
6.4.25 74xx133 (13-In NAND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13
6.4.26 74xx134 (12-In NAND w/3-state Out) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13
6.4.27 74xx135 (Quad Ex-OR/NOR Gate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14
6.4.28 74xx136 (Quad 2-in Exc-OR gate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14
6.4.29 74xx138 (3-to-8 Dec). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14
6.4.30 74xx139 (Dual 2-to-4 Dec/DEMUX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-15
6.4.31 74xx14 (Hex INVERTER (Schmitt)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-15
6.4.32 74xx145 (BCD-to-Decimal Dec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-16
6.4.33 74xx147 (10-to-4 Priority Enc). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-17
6.4.34 74xx148 (8-to-3 Priority Enc). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-17
6.4.35 74xx15 (3 3-Input AND). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18
6.4.36 74xx150 (1-of-16 Data Sel/MUX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18
6.4.37 74xx151 (1-of-8 Data Sel/MUX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-19
6.4.38 74xx152 (Data Sel/MUX). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-19
6.4.39 74xx153 (Dual 4-to-1 Data Sel/MUX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-20
6.4.40 74xx154 (4-to-16 Dec/DEMUX). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-20
6.4.41 74xx155 (Dual 2-to-4 Dec/DEMUX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-21
6.4.42 74xx156 (Dual 2-to-4 Dec/DEMUX (OC)) . . . . . . . . . . . . . . . . . . . . . . . . . 6-22
6.4.43 74xx157 (Quad 2-to-1 Data Sel/MUX) . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-22
6.4.44 74xx158 (Quad 2-to-1 Data Sel/MUX) . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-23
6.4.45 74xx159 (4-to-16 Dec/DEMUX (OC)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-23
6.4.46 74xx16 (Hex INVERTER (OC)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-24
6.4.47 74xx160 (Sync 4-bit Decade Counter (clr)) . . . . . . . . . . . . . . . . . . . . . . . . 6-25
6.4.48 74xx161 (Sync 4-bit Bin Counter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-25
6.4.49 74xx162 (Sync 4-bit Decade Counter) . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-26
6.4.50 74xx163 (Sync 4-bit Binary Counter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-27
6.4.51 74xx164 (8-bit Parallel-Out Serial Shift Reg) . . . . . . . . . . . . . . . . . . . . . . 6-28
6.4.52 74xx165 (Parallel-load 8-bit Shift Reg) . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-28
6.4.53 74xx166 (Parallel-load 8-bit Shift Reg) . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-29
6.4.54 74xx169 (Sync 4-bit up/down Binary Counter) . . . . . . . . . . . . . . . . . . . . . 6-29
6.4.55 74xx17 (Hex BUFFER (OC)). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-30
6.4.56 74xx173 (4-bit D-type Reg w/3-state Out). . . . . . . . . . . . . . . . . . . . . . . . . 6-30
6.4.57 74xx174 (Hex D-type FF (clr)). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-30

Multisim 8 Component Reference Guide ix

 6.4.58 74xx175 (Quad D-type FF (clr)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-31
6.4.59 74xx180 (9-bit Odd/even Par GEN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-31
6.4.60 74xx181 (Alu/Function Generator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-32
6.4.61 74xx182 (Look-ahead Carry GEN). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-33
6.4.62 74xx190 (Sync BCD up/down Counter) . . . . . . . . . . . . . . . . . . . . . . . . . . .6-35
6.4.63 74xx191 (Sync 4-bit up/down Counter) . . . . . . . . . . . . . . . . . . . . . . . . . . .6-36
6.4.64 74xx192 (Sync BCD Up/down Counter). . . . . . . . . . . . . . . . . . . . . . . . . . .6-36
6.4.65 74xx193 (Sync 4-bit Bin Up/down Counter) . . . . . . . . . . . . . . . . . . . . . . . .6-37
6.4.66 74xx194 (4-bit Bidirect Univ. Shift Reg) . . . . . . . . . . . . . . . . . . . . . . . . . . .6-38
6.4.67 74xx195 (4-bit Parallel-Access Shift Reg) . . . . . . . . . . . . . . . . . . . . . . . . .6-38
6.4.68 74xx198 (8-bit Shift Reg (shl/shr ctrl)) . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-39
6.4.69 74xx199 (8-bit Shift Reg (sh/ld ctrl)). . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-40
6.4.70 74xx20 (Dual 4-In NAND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-41
6.4.71 74xx21 (Dual 4-In AND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-41
6.4.72 74xx22 (Dual 4-In NAND (OC)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-42
6.4.73 74xx238 (3-to-8 line Dec/DEMUX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-42
6.4.74 74xx24 (Dual 4-input NAND Schmitt). . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-43
6.4.75 74xx240 (Octal BUFFER w/3-state Out) . . . . . . . . . . . . . . . . . . . . . . . . . .6-43
6.4.76 74xx241 (Octal BUFFER w/3-state Out) . . . . . . . . . . . . . . . . . . . . . . . . . .6-43
6.4.77 74xx244 (Octal BUFFER w/3-state Out) . . . . . . . . . . . . . . . . . . . . . . . . . .6-43
6.4.78 74xx246 (BCD-to-seven segment dec) . . . . . . . . . . . . . . . . . . . . . . . . . . .6-44
6.4.79 74xx247 (BCD-to-seven segment dec) . . . . . . . . . . . . . . . . . . . . . . . . . . .6-45
6.4.80 74xx248 (BCD-to-seven segment dec) . . . . . . . . . . . . . . . . . . . . . . . . . . .6-46
6.4.81 74xx249 (BCD-to-seven segment dec) . . . . . . . . . . . . . . . . . . . . . . . . . . .6-48
6.4.82 74xx25 (Dual 4-In NOR w/Strobe) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-49
6.4.83 74xx251 (Data Sel/MUX w/3-state Out) . . . . . . . . . . . . . . . . . . . . . . . . . . .6-49
6.4.84 74xx253 (Dual 4-to-1 Data Sel/MUX w/3-state Out) . . . . . . . . . . . . . . . . .6-50
6.4.85 74xx257 (Quad 2-to-1 line Data Sel/MUX). . . . . . . . . . . . . . . . . . . . . . . . .6-51
6.4.86 74xx258 (Quad 2-to-1 line Data Sel/MUX). . . . . . . . . . . . . . . . . . . . . . . . .6-51
6.4.87 74xx259 (8-bit Latch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-52
6.4.88 74xx26 (Quad 2-In NAND (OC)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-52
6.4.89 74xx266 (Quad 2-In XNOR (OC)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-52
6.4.90 74xx27 (Tri 3-In NOR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-53
6.4.91 74xx273 (Octal D-type FF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-54
6.4.92 74xx279 (Quad SR latches) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-54
6.4.93 74xx28 (Quad 2-In NOR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-54
6.4.94 74xx280 (9-bit odd/even parity generator/checker) . . . . . . . . . . . . . . . . . .6-55
6.4.95 74xx283 (4-bit Bin Full Add) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-55
6.4.96 74xx290 (Decade Counter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-55
6.4.97 74xx293 (4-bit Binary Counter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-56
6.4.98 74xx298 (Quad 2-In MUX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-56
6.4.99 74xx30 (8-In NAND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-57

x Electronics Workbench
 6.4.100 74xx32 (Quad 2-In OR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-57
6.4.101 74xx33 (Quad 2-In NOR (OC)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-58
6.4.102 74xx350 (4-bit Shifter w/3-state Out). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-58
6.4.103 74xx351 (Dual Data Sel/MUX w/3-state Out) . . . . . . . . . . . . . . . . . . . . . . 6-59
6.4.104 74xx352 (Dual 4-to-1 Data Sel/MUX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-59
6.4.105 74xx353 (Dual 4-to-1 Data Sel/MUX w/3-state Out) . . . . . . . . . . . . . . . . . 6-60
6.4.106 74xx365 (Hex Buffer/Driver w/3-state) . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-60
6.4.107 74xx366 (Hex Inverter Buffer/Driver w/3-state) . . . . . . . . . . . . . . . . . . . . . 6-61
6.4.108 74xx367 (Hex Buffer/Driver w/3-state) . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-61
6.4.109 74xx368 (Hex Inverter Buffer/Driver w/3-state) . . . . . . . . . . . . . . . . . . . . . 6-62
6.4.110 74xx37 (Quad 2-In NAND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-62
6.4.111 74xx373 (Octal D-type Transparent Latches) . . . . . . . . . . . . . . . . . . . . . . 6-63
6.4.112 74xx374 (Octal D-type FF (+edge)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-63
6.4.113 74xx375 (4-bit Bistable Latches) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-64
6.4.114 74xx377 (Octal D-type FF w/en) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-64
6.4.115 74xx378 (Hex D-type FF w/en) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-65
6.4.116 74xx379 (Quad D-type FF w/en) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-65
6.4.117 74xx38 (Quad 2-In NAND (OC)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-65
6.4.118 74xx39 (Quad 2-In NAND (OC)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-66
6.4.119 74xx390 (Dual Div-by-2, Div-by-5 Counter) . . . . . . . . . . . . . . . . . . . . . . . 6-66
6.4.120 74xx393 (Dual 4-bit Binary Counter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-68
6.4.121 74xx395 (4-bit Cascadable Shift Reg w/3-state Out) . . . . . . . . . . . . . . . . 6-69
6.4.122 74xx40 (Dual 4-In NAND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-69
6.4.123 74xx42 (4-BCD to 10-Decimal Dec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-70
6.4.124 74xx43 (Exc-3-to-Decimal Dec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-71
6.4.125 74xx44 (Exc-3-Gray-to-Decimal Dec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-72
6.4.126 74425 (Quad Bus Buffer with 3-State) . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-72
6.4.127 74426 (Quad Bus Buffer with 3-State) . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-72
6.4.128 74xx445 (BCD-to-Decimal Dec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-73
6.4.129 74xx45 (BCD-to-Decimal Dec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-74
6.4.130 74xx46 (BCD-to-seven segment dec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-74
6.4.131 74xx465 (Octal BUFFER w/3-state Out) . . . . . . . . . . . . . . . . . . . . . . . . . . 6-76
6.4.132 74xx466 (Octal BUFFER w/3-state Out) . . . . . . . . . . . . . . . . . . . . . . . . . . 6-76
6.4.133 74xx47 (BCD-to-seven segment dec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-76
6.4.134 74xx48 (BCD-to-seven segment dec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-78
6.4.135 74xx51 (AND-OR-INVERTER) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-79
6.4.136 74xx521 (8-Bit Identity Comparitor) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-80
6.4.137 74xx533 (Octal D-Latch with inverted O/Ps) . . . . . . . . . . . . . . . . . . . . . . . 6-80
6.4.138 74xx534 (Octal Flip-Flop with inverted Latches) . . . . . . . . . . . . . . . . . . . . 6-81
6.4.139 74xx54 (4-wide AND-OR-INVERTER) . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-81
6.4.140 74xx55 (2-wide 4-In AND-OR-INVERTER) . . . . . . . . . . . . . . . . . . . . . . . . 6-82
6.4.141 74xx573 (Octal D-type Latch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-82

Multisim 8 Component Reference Guide xi

 6.4.142 74xx574 (Octal D-type Flip-Flop) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-83
6.4.143 74xx640 (Octal Bus Transceiver) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-83
6.4.144 74xx645 (Octal Bus Transceiver) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-84
6.4.145 74xx69 (Dual 4-bit Binary Counter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-84
6.4.146 74xx72 (AND-gated JK MS-SLV FF (pre, clr)) . . . . . . . . . . . . . . . . . . . . . .6-84
6.4.147 74xx73 (Dual JK FF (clr)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-85
6.4.148 74xx74 (Dual D-type FF (pre, clr)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-85
6.4.149 74xx75 (4-bit Bistable Latches) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-86
6.4.150 74xx76 (Dual JK FF (pre, clr)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-86
6.4.151 74xx77 (4-bit Bistable Latches) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-87
6.4.152 74xx78 (Dual JK FF (pre, com clk & clr)) . . . . . . . . . . . . . . . . . . . . . . . . . .6-87
6.4.153 74xx82 (2-bit Bin Full Adder) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-89
6.4.154 74xx821 (10-Bit D-type Flip-Flop) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-89
6.4.155 74xx823 (9-Bit D-type Flip-Flop) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-90
6.4.156 74xx825 (8-Bit D-Type Flip-Flop) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-91
6.4.157 74xx827 (10-Bit Buffers/Line Drivers) . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-92
6.4.158 74xx828 (10-Bit Buffers/Line Drivers) . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-93
6.4.159 74xx83 (4-bit Bin Full Adder) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-93
6.4.160 74xx85 (4-bit Mag COMP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-94
6.4.161 74xx86 (Quad 2-In XOR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-94
6.4.162 74xx90 (Decade Counter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-95
6.4.163 74xx91 (8-bit Shift Reg) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-95
6.4.164 74xx92 (Divide-by-twelve Counter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-96
6.4.165 74xx93 (4-bit Binary Counter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-97

7. CMOS
7.1 CMOS Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
7.1.1 Power-Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2
7.1.2 Logic Voltage Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2
7.1.3 Noise Margins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2
7.1.4 Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2
7.2 4000 Series ICs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2
7.2.1 4000 (Dual 3-In NOR and INVERTER) . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-3
7.2.2 4001 (Quad 2-In NOR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-3
7.2.3 4002 (Dual 4-In NOR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-4
7.2.4 4007 (Dual Com Pair/Inv). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-4
7.2.5 4008 (4-bit Binary Full Adder) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-5
7.2.6 4010 (Hex BUFFER) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-6
7.2.7 40106 (Hex INVERTER (Schmitt)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-6
7.2.8 4011 (Quad 2-In NAND). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-7

xii Electronics Workbench

 7.2.9 4012 (Dual 4-In NAND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7
7.2.10 4013 (Dual D-type FF (+edge)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
7.2.11 4014 (8-bit Static Shift Reg) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9
7.2.12 4015 (Dual 4-bit Static Shift Reg) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10
7.2.13 40160 (4-bit Dec Counter). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11
7.2.14 40161 (4-bit Bin Counter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12
7.2.15 40162 (4-bit Dec Counter). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-13
7.2.16 40163 (4-bit Bin Counter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-13
7.2.17 4017 (5-stage Johnson Counter). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14
7.2.18 40174 (Hex D-type Flip-flop) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-15
7.2.19 40175 (Quad D-type Flip-flop). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-16
7.2.20 4018 (5-stage Johnson Counter). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-17
7.2.21 4019 (Quad 2-In MUX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-18
7.2.22 40192 (4-bit Dec Counter). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19
7.2.23 40193 (4-bit Bin Counter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19
7.2.24 40194 (4-bit Shift Register) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-20
7.2.25 40195 (4-bit Shift Register) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-20
7.2.26 4020 (14-stage Bin Counter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-21
7.2.27 4021 (8-bit Static Shift Register) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-21
7.2.28 4023 (Tri 3-In NAND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-22
7.2.29 4024 (7-stage Binary Counter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-23
7.2.30 40240 (Octal Inv Buffer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-23
7.2.31 40244 (Octal Non-inv Buffer). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-24
7.2.32 40245 (Octal Bus Transceiver) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-24
7.2.33 4025 (Tri 3-In NOR). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-24
7.2.34 4027 (Dual JK FF (+edge, pre, clr)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-25
7.2.35 4028 (1-of-10 Dec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-26
7.2.36 4029 (4-bit Bin/BCD Dec Counter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-27
7.2.37 4030 (Quad 2-In XOR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-28
7.2.38 4032 (Triple Serial Adder) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-29
7.2.39 4035 (4-bit Shift Register) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-29
7.2.40 40373 (Octal Trans Latch). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-31
7.2.41 40374 (Octal D-type Flip-flop) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-32
7.2.42 4038 (Triple Serial Adder) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-32
7.2.43 4040 (12-stage Binary Counter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-33
7.2.44 4041 (Quad True/Complement BUFFER) . . . . . . . . . . . . . . . . . . . . . . . . . 7-33
7.2.45 4042 (Quad D-latch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-34
7.2.46 4043 (Quad RS latch w/3-state Out) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-35
7.2.47 4044 (Quad RS latch w/3-state Out) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-35
7.2.48 4049 (Hex INVERTER) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-36
7.2.49 4050 (Hex BUFFER) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-36
7.2.50 4060 (14-Stage Binary Counter & Osc). . . . . . . . . . . . . . . . . . . . . . . . . . . 7-37

Multisim 8 Component Reference Guide xiii

 7.2.51 4066 (Quad Analog Switches) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-37
7.2.52 4068 (8-In NAND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-38
7.2.53 4069 (Hex INVERTER) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-38
7.2.54 4070 (Quad 2-In XOR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-39
7.2.55 4071 (Quad 2-In OR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-39
7.2.56 4072 (Dual 4-In OR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-40
7.2.57 4073 (Tri 3-In AND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-41
7.2.58 4075 (Tri 3-In OR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-42
7.2.59 4076 (Quad D-type Reg w/3-state Out) . . . . . . . . . . . . . . . . . . . . . . . . . . .7-43
7.2.60 4077 (Quad 2-In XNOR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-43
7.2.61 4078 (8-In NOR). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-44
7.2.62 4081 (Quad 2-In AND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-45
7.2.63 4082 (Dual 4-In AND). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-46
7.2.64 4085 (Dual 2-Wide 2-In AND-OR-INVERTER) . . . . . . . . . . . . . . . . . . . . .7-47
7.2.65 4086 (4-Wide 2-In AND-OR-INVERTER). . . . . . . . . . . . . . . . . . . . . . . . . .7-49
7.2.66 4093 (Quad 2-In NAND (Schmitt)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-49
7.2.67 4094 (8-stage Serial Shift Register) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-50
7.2.68 4099 (8-bit Latch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-51
7.2.69 4502 (Strobed hex INVERTER) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-51
7.2.70 4503 (Tri-state hex BUFFER w/Strobe) . . . . . . . . . . . . . . . . . . . . . . . . . . .7-52
7.2.71 4508 (Dual 4-bit latch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-52
7.2.72 4510 (BCD up/down Counter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-53
7.2.73 4511(BCD-to-seven segment latch/Dec) . . . . . . . . . . . . . . . . . . . . . . . . . .7-54
7.2.74 4512 (8-In MUX w/3-state Out) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-55
7.2.75 4514 (1-of-16 Dec/DEMUX w/Input latches) . . . . . . . . . . . . . . . . . . . . . . .7-57
7.2.76 4515 (1-of-16 Dec/DEMUX w/Input latches) . . . . . . . . . . . . . . . . . . . . . . .7-58
7.2.77 4516 (Binary up/down Counter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-59
7.2.78 4518 (Dual BCD Counter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-59
7.2.79 4519 (Quad Multiplexer). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-60
7.2.80 4520 (Dual Binary Counter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-60
7.2.81 4522 (4-bit BCD Down Counter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-61
7.2.82 4526 (4-bit Bin Down Counter). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-61
7.2.83 4531 (13-input Checker/Generator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-62
7.2.84 4532 (8-bit Priority Enc) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-63
7.2.85 4539 (Dual 4-input Multiplexer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-64
7.2.86 4543 (BCD-to-seven segment latch/dec/driver) . . . . . . . . . . . . . . . . . . . . .7-64
7.2.87 4544 (BCD-to-seven segment latch/dec) . . . . . . . . . . . . . . . . . . . . . . . . . .7-66
7.2.88 4555 (Dual 1-of-4 Dec/DEMUX). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-67
7.2.89 4556 (Dual 1-of-4 Dec/DEMUX). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-68
7.2.90 4585 (4-bit Comparator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-69

xiv Electronics Workbench

 7.3 Tiny Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-70
7.3.1 NC7S00. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-70
7.3.2 NC7S02. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-70
7.3.3 NC7S04. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-71
7.3.4 NC7S08. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-71
7.3.5 NC7S32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-71
7.3.6 NC7S86. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-72
7.3.7 NC7ST00. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-72
7.3.8 NC7ST02. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-73
7.3.9 NC7ST04. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-73
7.3.10 NC7ST08. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-73
7.3.11 NC7ST32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-74
7.3.12 NC7ST86. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-74
7.3.13 NC7SU04 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-75
7.3.14 NC7SZ00. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-75
7.3.15 NC7SZ02. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-75
7.3.16 NC7SZ04. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-76
7.3.17 NC7SZ05. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-76
7.3.18 NC7SZ08. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-77
7.3.19 NC7SZ125. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-77
7.3.20 NC7SZ126. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-77
7.3.21 NC7SZ32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-78
7.3.22 NC7SZ38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-78
7.3.23 NC7SZ86. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-78
7.3.24 NC7SZU04 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-79

8. Misc. Digital Components

8.1 TIL Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
8.1.1 AND Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
8.1.2 OR Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
8.1.3 NOT Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
8.1.4 NOR Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
8.1.5 NAND Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4
8.1.6 XOR Gate (Exclusive OR). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4
8.1.7 XNOR Gate (Exclusive NOR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5
8.1.8 Tristate Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6
8.1.9 Buffer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6
8.1.10 Schmitt Trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
8.1.11 Digital Pulldown. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8
8.1.12 Digital Pull-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8

Multisim 8 Component Reference Guide xv

 8.1.13 Digital State Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-8
8.1.14 Parity Generator/Checker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-9
8.1.15 Quad 2-to-1 Data Sel/MUX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-9
8.1.16 Digital Frequency Divider . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-9
8.2 VHDL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-10
8.3 Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-12
8.4 Line Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-12
8.5 Line Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-12
8.6 Line Transceiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-13
8.7 CPLDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-13
8.8 DSP Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-13
8.9 FPGA Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-14
8.10 Microcontrollers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-14
8.11 Programmable Logic Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-15
8.12 Microprocessors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-15

9. Mixed Components
9.1 ADC DAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-1
9.1.1 Characteristic Equation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-1
9.2 Analog Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-2
9.3 Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-3
9.3.1 Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-3
9.4 Mono Stable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-4
9.4.1 Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-4
9.5 Phase-Locked Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-4
9.5.1 Characteristic Equation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-5
9.5.2 Phase-Locked Loop Parameters and Defaults . . . . . . . . . . . . . . . . . . . . . .9-6
9.6 Multivibrators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-6
9.6.1 CD4538BC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-6
9.6.2 SN74121N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-7
9.6.3 SN74123 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-8
9.6.4 SN74130N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-8

xvi Electronics Workbench

 9.7 Frequency Divider . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8

10. Indicators
10.1 Voltmeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
10.1.1 Resistance (1.0 W - 999.99 TW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
10.1.2 Mode (DC or AC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
10.1.3 Connecting a Voltmeter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2
10.2 Ammeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2
10.2.1 Resistance (1.0 pW - 999.99 W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2
10.2.2 Mode (DC or AC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2
10.2.3 Connecting an Ammeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2
10.3 Probe (LED) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3
10.4 Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3
10.4.1 Time-Domain and AC Frequency Models . . . . . . . . . . . . . . . . . . . . . . . . . 10-3
10.5 Hex Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4
10.5.1 Seven-Segment Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4
10.5.2 Decoded Seven-Segment Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6
10.6 Bargraphs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-7
10.6.1 The Component. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-7
10.6.1.1 Bargraph Display Parameters and Defaults . . . . . . . . . . . . . . . 10-7
10.6.2 Decoded Bargraph Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-7
10.6.2.1 Decoded Bargraph Display Parameters and Defaults. . . . . . . . 10-8
10.7 Buzzer/Sonalert Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-8

11. Misc. Components

11.1 Crystal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1
11.2 DC Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2
11.2.1 Characteristic Equations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-3
11.2.2 DC Motor Parameters and Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-4
11.3 Optocoupler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-4
11.4 Vacuum Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-5
11.4.1 Characteristic Equations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-5
11.4.2 Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-6
11.4.3 Triode Vacuum Tube Parameters and Defaults . . . . . . . . . . . . . . . . . . . . 11-6

Multisim 8 Component Reference Guide xvii

 11.5 Voltage Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-6
11.6 Voltage Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-7
11.6.1 Input/Output Voltage Differential Rating. . . . . . . . . . . . . . . . . . . . . . . . . . .11-8
11.7 Voltage Suppressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-8
11.8 Boost Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-9
11.8.1 Characteristic Equations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-9
11.8.2 Boost Converter Parameters and Defaults . . . . . . . . . . . . . . . . . . . . . . .11-10
11.9 Buck Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-11
11.9.1 Characteristic Equations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-11
11.9.2 Buck Converter Parameters and Defaults . . . . . . . . . . . . . . . . . . . . . . . .11-12
11.10 Buck Boost Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-12
11.10.1 Characteristic Equations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-13
11.10.2 Buck-Boost Converter Parameters and Defaults . . . . . . . . . . . . . . . . . . .11-14
11.11 Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-14
11.11.1 Characteristic Equations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-15
11.11.2 Fuse Parameters and Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-15
11.12 Lossy Transmission Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-15
11.12.1 Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-16
11.12.2 Lossy Transmission Line Model Parameters and Defaults . . . . . . . . . . .11-17
11.13 Lossless Line Type 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-17
11.13.1 Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-18
11.13.2 Lossless Transmission Line Model Parameters and Defaults . . . . . . . . .11-19
11.13.3 Lossless Line Type 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-19
11.14 Net . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-19
11.15 Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-19
11.16 Miscellaneous Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-20
11.17 PWM Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-20
11.18 Miscellaneous Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-21
11.19 Power Supply Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-21
11.20 MOSFET Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-21
11.21 Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-21

xviii Electronics Workbench

12. RF Components
12.1 RF Capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1
12.2 RF Inductor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2
12.3 RF Bipolar Transistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2
12.4 RF MOS_3TDN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-3
12.5 Tunnel Diode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-3
12.6 Strip Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-4

13. Electromechanical Components

13.1 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1
13.2 Supplementary Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-2
13.3 Momentary Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-2
13.4 Line Transformer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-2
13.5 Coils, Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-3
13.6 Timed Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-3
13.7 Protection Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-4
13.8 Output Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-4
13.9 Push Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-5
13.10 Pilot Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-5
13.11 Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-5

Multisim 8 Component Reference Guide xix

xx Electronics Workbench
Chapter 1
Source Components

1.1 Ground

1.1.1 About Grounding

A voltage measurement is always referenced to some point, since a voltage is actually a
“potential difference” between two points in a circuit.
The concept of “ground” is a way of defining a point common to all voltages. It represents 0
volts. All voltage levels around the circuit are positive or negative when compared to ground.
In power systems, the planet Earth itself is used for this reference point (most home power
circuits are ultimately “grounded” to the Earth's surface for lightning protection). This is how
the expression “earthing” or “grounding” a circuit originated.
Most modern power supplies have “floating” positive and negative outputs, and either output
point can be defined as ground. These types of supplies can be used as positive (with respect
to ground) or negative power supplies. In floating power supply circuits, the positive output is
often used as the voltage reference for all parts of the circuit.
Note Multisim supports a multipoint grounding system. Each ground connected is made
directly to the ground plane.

Multisim 8 Component Reference Guide 1-1

Source Components

1.1.2 The Ground Component

This component has 0 voltage and so provides a clear reference point for calculating electrical
values. You can use as many ground components as you want. All terminals connected to
ground components represent a common point and are treated as joined together.
Not all circuits require grounding for simulation; however, any circuit that uses an opamp,
transformer, controlled source or oscilloscope must be grounded. Also, any circuit which
contains both analog and digital components should be grounded. If a circuit is ungrounded or
improperly grounded (even if it does not need grounding in reality), it may not be simulated.
If it is simulated, it may produce inconsistent results. The linear transformer must be
grounded on both sides.

1.2 Digital Ground

The digital ground is used to connect ground to the digital components which do not have an
explicit ground pin. The digital ground must be placed on the schematic but should not be
connected to any component.

1.3 DC Voltage Source (Battery)

1.3.1 Battery Background Information

A battery may be a single electrochemical cell or a number of electrochemical cells wired in
series. It is used to provide a direct source of voltage and/or current.
A single cell has a voltage of approximately 1.5 volts, depending on its construction. It
consists of a container of acid in which an electrode is placed. Chemical action causes
electrons to flow between the electrode and the container, and this creates a potential
difference between the electrode and the material of the container.

1-2 Electronics Workbench

 VCC Voltage Source

Batteries can be rechargeable and can be built to deliver extremely high currents for long
periods. The automobile ignition battery is an application of a battery as a “current source”;
the voltage may vary considerably under use, with no visible battery deterioration.
Batteries may be used as voltage references, their voltage remaining stable and predictable to
many figures of accuracy for many years. The standard cell is such an application. A standard
cell is a voltage source, and it is important that current is not drawn from the standard cell.

1.3.2 Battery Component

This source can be adjusted from microvolts to kilovolts, but the value must be greater than
zero.
Tip The battery in Multisim has no resistance. If you want to use a battery in parallel with
another battery or a switch, insert a 1-mW resistor in series with it.
Battery tolerance is, by default, set to the global tolerance (defined in the Analysis/Monte
Carlo dialog box). To set the tolerance explicitly, de-select “Use global tolerance” and enter a
value in the “voltage tolerance” field.

1.4 VCC Voltage Source

The VCC Voltage Source is used to connect power to the digital components which do not
have an explicit power pin. The VCC Voltage Source must be placed on the schematic and
can be used as a DC voltage source. The value of VCC can be set by using the Digital Power
dialog box, which appears when you double-click on the VCC symbol. Multiple VCC
symbols may be placed on a schematic but there is only one VCC net in the schematic. Only
one value of VCC voltage is possible in the design with both positive and negative values
being supported.

Multisim 8 Component Reference Guide 1-3

Source Components

1.5 DC Current Source

The current generated by this source can be adjusted from microamps to kiloamps.
DC current source tolerance is, by default, set to the global tolerance (defined in the Analysis/
Monte Carlo dialog box). To set the tolerance explicitly, de-select “Use global tolerance” and
enter a value in the “current tolerance” field.

1.6 AC Voltage Source

The root-mean-square (RMS) voltage of this source can be adjusted from µV to kilovolts. You
can also control its frequency and phase angle.

V peak
VRMS =
2
AC voltage source tolerance is, by default, set to the global tolerance (defined in the Monte
Carlo Analysis screen). To set the tolerance explicitly, de-select “Use global tolerance” and
enter a value in the “voltage tolerance” field.

1-4 Electronics Workbench

 AC Current Source

1.7 AC Current Source

The RMS current of this source can be adjusted from microamps to kiloamps. You can also
control its frequency and phase angle.
I peak
IRMS =
2
AC current source tolerance is, by default, set to the global tolerance (defined in the Analysis/
Monte Carlo dialog box). To set the tolerance explicitly, de-select “Use global tolerance” and
enter a value in the “current tolerance” field.

1.8 Clock Source

This component is a square wave generator. You can adjust its voltage amplitude, duty cycle
and frequency.

1.9 Amplitude Modulation (AM) Source

The AM source (single-frequency amplitude modulation source) generates an amplitude-

modulated wave. It can be used to build and analyze communications circuits.

Multisim 8 Component Reference Guide 1-5

Source Components

1.9.1 Characteristic Equation

The behavior of the AM source is described by:

VOUT = vc∗ sin( 2∗ π ∗ fc∗ TIME )∗ (1 + m∗ sin( 2∗ π ∗ fm∗ TIME ))

where

vc = carrier amplitude, in volts

fc = carrier frequency, in hertz

m = modulation index

fm = modulation frequency, in hertz

1.10 FM Source
The FM source (single-frequency frequency modulation source) generates a frequency-
modulated wave. It can be used to build and analyze communications circuits.The signal
output can be either a current source or a voltage source.

1.10.1 FM Voltage Source

This is an FM source of which the output is measured in voltage.

1-6 Electronics Workbench

 FM Source

1.10.2 Characteristic Equation

The behavior of the FM voltage source is described by:

VOUT = va∗ sin( 2∗ π ∗ fc∗ TIME + m∗ sin( 2∗ π ∗ fm∗ TIME ))

where

va = peak amplitude, in volts

fc = carrier frequency, in Hz

m = modulation index

fm = modulation frequency, in Hz

1.10.3 FM Current Source

This component is the same as the FM voltage source, except that the output is measured in
current.

1.10.4 Characteristic Equation

The behavior of the FM current source is described by the same equation as in E.10.2, with
Vout replaced by Iout.

Multisim 8 Component Reference Guide 1-7

Source Components

1.11 FSK Source

This source is used for keying a transmitter for telegraph or teletype communications by
shifting the carrier frequency over a range of a few hundred hertz. The frequency shift key
(FSK) modulated source generates the mark transmission frequency, f1, when a binary 1 is
sensed at the input, and the space transmission frequency, f2, when a 0 is sensed.
FSK is used in digital communications systems such as in low speed modems (for example, a
Bell 202 type modem - 1200 baud or less).
In this system, a digital high level is referred to as a MARK and is reproduced as a frequency
of 1200 Hz. A digital low level is referred to as a SPACE and is represented by a frequency of
2200 Hz.
In the example shown below, the frequency shift keying signal is a 5v (TTL) square wave.
When the keying input is 5V, a MARK frequency of 1200 Hz is output. When keying voltage
is 0V, a SPACE frequency of 2200 Hz is output.

1-8 Electronics Workbench

 Voltage-Controlled Voltage Source

This component is a square wave generator. You can adjust its voltage amplitude, duty cycle
and frequency.

1.12 Voltage-Controlled Voltage Source

The output voltage of this source depends on the voltage applied to its input terminal. The
ratio of the output voltage to the input voltage determines its voltage gain (E). Voltage gain
can have any value from mV/V to kV/V.

V OUT
E=
V IN

1.13 Current-Controlled Voltage Source

The output voltage of this source depends on the current through the input terminals. The two
are related by a parameter called transresistance (H), which is the ratio of the output voltage to
the input current. It can have any value from mW to kW.
V OUT
H =
I IN

Multisim 8 Component Reference Guide 1-9

Source Components

1.14 Voltage-Controlled Current Source

The output current of this source depends on the voltage applied at the input terminals. The
two are related by a parameter called transconductance (G), which is the ratio of the output
current to the input voltage. It is measured in mhos (also known as seimens) and can have any
value from mmhos to kmhos.
I OUT
G=
V IN

1.15 Current-Controlled Current Source

The magnitude of the current output of a current-controlled current source depends on the
current through the input terminals. The two are related by a parameter called current gain (F),
which is the ratio of the output current to the input current. The current gain can have any
value from mA/A to kA/A.

I OUT
F=
I IN

1-10 Electronics Workbench

 Voltage-Controlled Sine Wave

1.16 Voltage-Controlled Sine Wave

1.16.1 The Component

This oscillator takes an input AC or DC voltage, which it uses as the independent variable in
the piecewise linear curve described by the (control, frequency) pairs. From the curve, a
frequency value is determined, and the oscillator outputs a sine wave at that frequency. When
only two co-ordinate pairs are used, the oscillator outputs a linear variation of the frequency
with respect to the control input. When the number of co-ordinate pairs is greater than two,
the output is piecewise linear. You can change the peak and valley values of the output sine
wave by resetting the Output peak high value and Output peak low value on the model
parameter dialog box.

1.16.2 Example
The example shows a sine wave generator with output frequency determined by a control
voltage.
Control voltage may be DC, controlled by a potentiometer, as is the case for many signal
generators and function generators, or may be the output from a PLL that determines a precise
frequency.
Control voltage may be a continuous variable of any desired shape as required in sweep
generators and spectrum analysers.
In the example shown below, the VCO parameters are set so that control voltage of 0V
produces an output frequency of 100Hz and a control voltage of 12V produces an output
frequency of 20KHz.

Multisim 8 Component Reference Guide 1-11

Source Components

A square wave control voltage produces a form of FSK (frequency shift keying), a sine wave
control voltage produces a form of FM (frequency modulation).

1-12 Electronics Workbench

 Voltage-Controlled Square Wave

1.17 Voltage-Controlled Square Wave

1.17.1 The Component

This oscillator is identical to the voltage-controlled sine wave oscillator except that it outputs
a square wave. This oscillator takes an input AC or DC voltage, which it uses as the
independent variable in the piecewise linear curve described by the (control, frequency) pairs.
From the curve, a frequency value is determined, and the oscillator outputs a square wave at
that frequency. When two co-ordinate pairs are used, the oscillator outputs a linear variation
of the frequency with respect to the control input. When the number of co-ordinate pairs is
greater than two, the output is piecewise linear. You can change duty cycle, rise and fall times,
and the peak and valley values of the output square wave by resetting the Output peak high
value and Output peak low value on the model parameter dialog box.

1.17.2 Example
The example shows a square wave generator with output frequency determined by a control
voltage.
Control voltage may be DC, controlled by a potentiometer, as is the case for many signal
generators and function generators.
Control voltage may be a continuous variable of any desired shape as required in sweep
generators and spectrum analysers.
In the example shown below, the VCO parameters are set so that control voltage of 0V
produces an output frequency of 100Hz and control voltage of 12V produces an output
frequency of 20KHz.

Multisim 8 Component Reference Guide 1-13

Source Components

A square wave control voltage produces a form of FSK (frequency shift keying), a sine wave
control voltage produces a form of FM (frequency modulation).

1-14 Electronics Workbench

 Voltage-Controlled Triangle Wave

1.18 Voltage-Controlled Triangle Wave

1.18.1 The Component

This oscillator is identical to the voltage-controlled sine wave oscillator except that it outputs
a triangle wave. This oscillator takes an input AC or DC voltage, which it uses as the
independent variable in the piecewise linear curve described by the (control, frequency) pairs.
From the curve, a frequency value is determined, and the oscillator outputs a triangle wave at
that frequency. When two co-ordinate pairs are used, the oscillator outputs a linear variation
of the frequency with respect to the control input. When the number of co-ordinate pairs is
greater than two, the output is piecewise linear. You can change the rise time duty cycle and
the peak and valley values of the output triangle wave by resetting the Output peak high value
and Output peak low value on the model parameter dialog box.

1.18.2 Example
The example shows a triangle wave generator with output frequency determined by a control
voltage.
Control voltage may be DC, controlled by a potentiometer, as is the case for many signal
generators and function generators.
Control voltage may be a continuous variable of any desired shape as required in sweep
generators and spectrum analysers.
In the example shown below, the VCO parameters are set so that control voltage of 0V
produces an output frequency of 100Hz and control voltage of 12V produces an output
frequency of 20KHz.

Multisim 8 Component Reference Guide 1-15

Source Components

A square wave control voltage produces a form of FSK (frequency shift keying), a sine wave
control voltage produces a form of FM (frequency modulation).

1.19 Voltage-Controlled Piecewise Linear Source

This source (voltage-controlled piecewise linear source) allows you to control the shape of the
output waveform by entering up to five (input, output) pairs, which are shown in the
Properties dialog box as (X,Y) co-ordinates.

1-16 Electronics Workbench

 Voltage Controlled Resistor

The X values are input co-ordinate points and the associated Y values represent the outputs of
those points. If you use only two pairs, the output voltage is linear.
Outside the bounds of the input co-ordinates, the PWL-controlled source extends the slope
found between the lowest two co-ordinate pairs and the highest two co-ordinate pairs. A
potential effect of this behavior is that it can unrealistically cause the output to reach a very
large or very small value, especially for large input values. Therefore, keep in mind that this
source does not inherently provide a limiting capability.

In order to reduce the potential for non-convergence of simulations, the PWL-controlled

source provides for smoothing around the co-ordinate pairs. If input smoothing domain (ISD)
is set to, say, 10%, the simulator assumes a smoothing radius about each co-ordinate point
equal to 10% of the length of the smaller of the segments above and below each co-ordinate
point.

1.20 Voltage Controlled Resistor

The resistance of this device is controlled by the voltage that is applied across the “+” and “-”
terminals. For every volt applied, the resistance increases by the amount set in the Value tab of

Multisim 8 Component Reference Guide 1-17

Source Components

the resistor’s properties window. The default value is 1 kOhm per volt. You can change this as
desired in the Resistance field of the Value tab.

1.21 Piecewise Linear Source

1.21.1 The Component

The signal output of this component can be either a current source or a voltage source.
This source allows you to control the shape of the waveform by entering time and voltage/
current pairs of values. Each pair of values specifies the value of the source at the specified
time. At intermediate values of time, the value of the source is determined by linear
interpolation.
The component has two terminals and behaves as a current or voltage source when connected
in a circuit. It reads a specified file which contains a table of time and current/voltage points.
Using the data in the table, the component generates a current/voltage waveform specified by
the input text file.

To use the PWL source:
1. Drag PWL Source from the Sources toolbar to the circuit window.
2. Double-click the component.
3. Select the file containing the voltage/current and time points from the dialog box. (See
“Input Text File Specification” below.)
Outside the bounds of the input co-ordinates, the PWL-controlled source extends the slope
found between the lowest two co-ordinate pairs and the highest two co-ordinate pairs. A
potential effect of this behavior is that it can unrealistically cause the output to reach a very
large or very small value, especially for large input values. Therefore, keep in mind that this
source does not inherently provide a limiting capability.
In order to reduce the potential for non-convergence of simulations, the PWL-controlled
source provides for smoothing around the co-ordinate pairs. If input smoothing domain (ISD)
is set to, say, 10%, the simulator assumes a smoothing radius about each co-ordinate point
equal to 10% of the length of the smaller of the segments above and below each co-ordinate
point.

1.21.1.1 Example
In the sample circuit shown below, a triangle waveform with uniform rise and fall slopes is
modified to a parabolic waveform for which the slope increases at each reference point.

1-18 Electronics Workbench

 Piecewise Linear Source

The co-ordinate pairs that perform this conversion are:

First pair 0,0 (no change)

Second pair 1,1 (same)

Third pair 2,4 (slope is increased between this pair and the last)

Fourth pair 3,9 (slope increased again)

Fifth 4,16 (even steeper slope)

Note In this example, the Y (output) is the square of the input. It is therefore an exponential.

1.21.1.2 Input Text File Specification

This file must contain a list of time and voltage/current points. Each line of the file represents
one point. The format is:
Time <space(s)> Voltage
or
Time <space(s)> Current

Multisim 8 Component Reference Guide 1-19

Source Components

You can leave any amount of space between the Time and Voltage/Current fields. Here is an
example of an ideally formatted input file:

0 0

2.88e-06 0.0181273

5.76e-06 0.0363142

1e-05 0.063185

1.848e-05 0.117198

If the PWL source encounters... It will...

non-whitespace at beginning of line ignore line

non-numeric data following correctly formatted accept data, ignore non-

data numeric data

non-whitespace between Time and Voltage/ ignore line

Current

whitespace preceding correctly formatted data accept data, ignore

whitespace

1.21.1.3 Special Considerations

If the earliest input point is not at time 0.0, then the PWL source gives the output of the
earliest time point from time 0.0 to that earliest time.
After the latest input point, the PWL source gives the output of the latest time point in the file
from that latest time until the simulation ends.
Between input points, the PWL source uses linear interpolation to generate output.
The PWL source can handle unsorted data. It sorts the points by time before the simulation
starts.
If you do not specify a file name, the PWL source behaves as a short circuit.
An easy way to generate an input file for the PWL source is to capture data using the Write
Data component (described in the Miscellaneous Parts Bin chapter). If you capture more than
one node with Write Data and then use the resulting file for the PWL source, only the
waveform V1 will be used.

1-20 Electronics Workbench

 Pulse Source

1.21.2 Piecewise Linear Voltage Source

This component is a piecewise linear source of which the output is measured in voltage.

1.21.3 Piecewise Linear Current Source

This component is the same as the Piecewise Linear Voltage Source, except that the output is
measured in current.

1.22 Pulse Source

This source includes pulse voltage source and pulse current source.The Pulse sources are
configurable sources whose output can be set to produce periodic pulses.
The following parameters can be modified:
• Initial Value
• Pulsed Value
• Delay time
• Rise Time
• Fall time
• Pulse Width
• Period

Multisim 8 Component Reference Guide 1-21

Source Components

1.22.1 Pulse Voltage Source

This component is a pulse source of which the output is measured in voltage.

1-22 Electronics Workbench

 Polynomial Source

1.22.2 Pulse Current Source

This component is the same as the Pulse Voltage Source, except that the output is measured in
current.

1.23 Polynomial Source

This is a voltage-controlled voltage source defined by a polynomial transfer function. It is a

specific case of the more general nonlinear dependent source. Use it for analog behavioral
modeling.
The polynomial source has three controlling voltage inputs, namely, V1, V2 and V3.

Multisim 8 Component Reference Guide 1-23

Source Components

1.23.1 Output Voltage Characteristic Equation

The output voltage is given by:
VOUT = A + B∗V 1 + C∗V 2 + D∗V 3 + E ∗V 12 + F ∗V 1∗V 2 + G∗V 1∗V 3
+ H ∗V 2 2 + I ∗V 2∗V 3 + J ∗V 3 2 + K ∗V 1∗V 2∗V 3
where

A = constant

B = coefficient of V1

C = coefficient of V2

D = coefficient of V3

E = coefficient of V1²

F = coefficient of V1*V2

G = coefficient of V1*V3

H = coefficient of V2²

I = coefficient of V2*V3

J = coefficient of V3²

K = coefficient of V1*V2*V3

1.24 Exponential Source

The exponential sources are configurable sources whose output can be set to produce an
exponential signal.
The following parameters can be modified:
• Initial Value
• Pulsed Value
• Rise Delay time
• Rise Time
• Fall Delay time
• Fall Time

1-24 Electronics Workbench

 Exponential Source

1.24.1 Exponential Voltage Source

This component is an exponential source of which the output is measured in voltage.

Multisim 8 Component Reference Guide 1-25

Source Components

1.24.2 Exponential Current Source

This component is the same as the Exponential Voltage Source, except that the output is
measured in current.

1.25 Nonlinear Dependent Source

Use this source for analog behavioral modeling. This generic source allows you to create a
sophisticated behavioral model by entering a mathematical expression. Expressions may
contain the following operators:

+ - * / ^ unary-

and these predefined functions:

abs asin atanh exp sin tan

acos asinh cos ln sinh u

acosh atan cosh log sqrt uramp

1-26 Electronics Workbench

 Controlled One-Shot

The functions u (unit step function) and uramp (integral of unit step) are useful in
synthesizing piecewise nonlinear functions.

1 for x≥0
u( x ) = 
0 for x < 0

x for x≥0
uramp( x ) = 
0 for x < 0

If the argument of log, ln or sqrt becomes less than zero, the absolute value of the argument is
used. If a divisor becomes zero or the argument of log or ln becomes zero, an error will result.
The small-signal AC behavior of this source is a linear dependent source with a
proportionality constant equal to the derivative of the source at the DC operating point.
Mathematical expression examples:

i = cos(v(1)) + sin(v(2))

v = ln(cos(log(v(1,2))^2)) - v(3) ^ 4 + v(2) ^ v(1)

i = 17

To use the nonlinear dependent source:

1. Double-click the component.
2. Type the algebraic expression.
Note If the dependent variable is “V” the output is in volts; if the dependent variable is “I”
the output is current.

1.26 Controlled One-Shot

This oscillator takes an AC or DC input voltage, which it uses as the independent variable in
the piecewise linear curve described by the (control, pulse width) pairs. From the curve, a
pulse width value is determined, and the oscillator outputs a pulse of that width. You can
change clock trigger value, output delay from trigger, output delay from pulse width, output
rise and fall times, and output high and low values.

Multisim 8 Component Reference Guide 1-27

Source Components

When only two co-ordinate pairs are used, the oscillator outputs a linear variation of the pulse
with respect to the control input. When the number of co-ordinate pairs is greater than two,
the output is piecewise linear.

1.27 Magnetic Flux Source

This device is used with a Hall Effect Sensor.

The Magnetic Flux Source uses the “B” key to change the density and polarity of the
magnetic flux impacting on a Hall Effect Sensor. You must specify the sphere of influence of
the magnetic flux source by entering an integer value in the Magnetic Channel field in the
Value tab of the component’s properties screen.
The Magnetic Channel field on the Hall Effect Sensor must have a matching integer value for
that sensor to be influenced by the source. No two magnetic flux sources or generators should
have the same integer value in the Magnetic Channel field. You can have as many Hall Effect
Sensors as you wish to react to any given source/generator and as many different sources/
generators as desired as long as each source/generator has a different integer value.

1.28 Magnetic Flux Generator

This device is used with a Hall Effect Sensor.

The Magnetic Flux Generator produces a continuous varying magnetic field (sinusoidal with
N and S peaks). You can define the flux density, rate of rotation (translating to frequency) and
specify the sphere of influence of the generator by putting a unique integer value in the
Magnetic Channel field in the Value tab of the source’s properties screen.
The Magnetic Channel field on the Hall Effect Sensor must have a matching integer value for
that sensor to be influenced by the generator. No two magnetic flux generators or sources

1-28 Electronics Workbench

 Multiplier

should have the same integer value in the Magnetic Channel field. You can have as many Hall
Effect Sensors as you wish to react to any given source/generator and as many different
sources/generators as desired as long as each source/generator has a different integer value.

1.29 Multiplier

This component multiplies two input voltages.

The basic function multiplies the X and Y inputs.
Vo = Vx * Vy
Gain factors may be applied to the X and Y inputs and to the output.
Examples shown below:
a) Two DC voltages are multiplied (4V * 2V = 8V)
b) Two volts DC multiplied by 2v RMS (2V * 2v RMS = 4v RMS)
c) Two AC signals, 2sinx and 4 cosx

Multisim 8 Component Reference Guide 1-29

Source Components

1-30 Electronics Workbench

 Divider

1.29.1 Characteristic Equation

The output voltage is given by:

( ( ) (
Vout = K X K Vx + X off ∗ Yk Vy + Yoff )) + off
where

Vx = input voltage at x

Vy = input voltage at y

Other symbols used in these equations are defined in “Multiplier Parameters and Defaults”.

1.29.2 Multiplier Parameters and Defaults

Symbol Parameter Name Default Unit

k Output gain 0.1 V/V

off Output 0.0 V

Yoff Y offset 0.0 V

Yk Y gain 1.0 V/V

Xoff X offset 0.0 V

Xk X gain 1.0 V/V

1.30 Divider

This component divides one voltage (the y input, or numerator) by another (the x input, or
denominator).

Multisim 8 Component Reference Guide 1-31

Source Components

Vo = Vy/Vx
You can limit the value of the denominator input to a value above zero by using the parameter
XLowLim. This limit is approached through a quadratic smoothing function, the domain of
which you can specify as an absolute value in XDS.
In the example shown below, the 120v RMS (339.38v peak to peak) sine wave at the Y input
is divided by a 16.96V DC voltage at the X input. The result is 339.38v (peak to peak) /
16.97V = 20v peak to peak.
If Vx is replaced with a 12v RMS voltage, in phase with Vy, the output will be 10V DC.
CAUTION If the X (denominator) voltage crosses 0v when any voltage is present at the Y
(numerator) terminal, the quotient will go to infinity and a large positive or negative “spike”
will be observed on the scope.

1-32 Electronics Workbench

 Divider

1.30.1 Characteristic Equation

(
 Vy + Yoff ∗ Yk 
Vout = 
)
 ∗ k + off
 x
V(+ X off ∗ X 
k )
where

Vx = input voltage at x

Vy = input voltage at y

Other symbols used in these equations are defined in the table below.

1.30.2 Divider Parameters and Defaults

Symbol Parameter Name Default Unit

k Output gain 1 V/V

off Output offset 0 V

Yoff Y (Numerator) offset 0 V

Yk Y (Numerator) gain 1 V/V

Xoff X (Denominator) offset 0 V

Xk X (Denominator) gain 1 V/V

XLowLim X (Denominator) lower limit 100 pV

XSD X (Denominator) smoothing domain 100 pV

Multisim 8 Component Reference Guide 1-33

Source Components

1.31 Transfer Function Block

This component models the transfer characteristic of a device, circuit or system in the s
domain. The transfer function block is specified as a fraction with polynomial numerators and
denominators. A transfer function up to the third order can be directly modeled. This
component may be used in DC, AC and transient analyses.

1.31.1 Characteristic Equation

This transfer function model is defined in a form of the rational function:

Y ( s) A3 s 3 + A2 s 2 + A1 s + A0
T ( s) = = K∗
X ( s) B3 s 3 + B2 s 2 + B1 s + B0

Transfer functions up to the third order may be modeled.

In the example shown below, the transfer function for a simple first order low pass filter is
used. Only the numerator and denominator constants A0 and B0 are required in this case.
These are equal to two pi times the cutoff frequency (first pole).

1-34 Electronics Workbench

 Transfer Function Block

The cursor on the Bode Plotter may be used to confirm first order performance with -3dB at
10kHz. and rolloff of 6dB per octave above 20kHz.

1.31.2 Transfer Function Block Parameters and Defaults

Symbol Parameter Name Default Unit

VIoff Input voltage offset 0 V

K Gain 1 V/V

VINT Integrator stage initial conditions 0 V

w Denormalized corner frequency 1 -

A3 Numerator 3rd order coefficient 0 -

A2 Numerator 2nd order coefficient 0 -

A1 Numerator 1st order coefficient 0 -

A0 Numerator constant 1 -

B3 Denominator 3rd order coefficient 0 -

Multisim 8 Component Reference Guide 1-35

Source Components

Symbol Parameter Name Default Unit

B2 Denominator 2nd order coefficient 0 -

B1 Denominator 1st order coefficient 0 -

B0 Denominator constant 1 -

1.32 Voltage Gain Block

This component multiplies the input voltage by the gain and delivers it to the output. This
represents a voltage amplifier function with the gain factor, K, selectable with the Value tab of
the component’s properties screen. The voltage gain block is used in control systems and
analog computing applications.
In the example shown below, the input is a 0.707v RMS (2v peak to peak) sine wave and the
gain factor K is set at 5. The output then is K times the input.
(.707*5= 3.535v RMS or 10 v peak to peak)

Caution Using the default model, as in this example, sine wave inputs
may be any value.

1-36 Electronics Workbench

 Voltage Gain Block

Suitable settings of model parameters will allow for virtually unlimited flexibility for
practical applications.

1.32.1 Characteristic Equation

Vout = K (Vin + VIoff ) + VOoff

1.32.2 Voltage Gain Block Parameters and Defaults

Symbol Parameter Name Default Unit

K Gain 1 V/V

VIoff Input offset voltage 0 V

VOoff Output offset voltage 0 V

Multisim 8 Component Reference Guide 1-37

Source Components

1.33 Voltage Differentiator

This component calculates the derivative of the input voltage (the transfer function, s) and
delivers it to the output. It is used in control systems and analog computing applications.
Differentiation may be described as a “rate of change” function and defines the slope of a
curve.
Rate of change = dV/dT

1.33.1 Investigations
1.33.1.1 Sine wave
The slope of a sine wave changes continuously and smoothly. Therefore, the differentiator
output should follow the sine shape.
In the example circuit shown below, if you change frequency from 10Hz. to 100Hz., the rate
of change of the waveform will increase by a factor of 10. The differentiator output will also
increase by the same factor. When investigating, note also a 90 degree phase shift from input
to output.

1.33.1.2 Triangle waveforms

In an ideal triangle waveform the rising and falling slopes are constant with an abrupt change
taking place at the peaks.
Since the rate of change (slope) during rise and fall are constant, the differential result is also
constant.
The reversal of slope at the peaks (from rise to fall/fall to rise) produces a large instantaneous
change in the differentiator output, resulting in a square wave output.
In the example circuit, as for the sine wave, if you change frequency from 10Hz. to 100Hz.,
the rate of change of the waveform will increase by a factor of 10. The differentiator output
will also increase by the same factor.

1-38 Electronics Workbench

 Voltage Differentiator

1.33.1.3 Square waves

In an ideal square wave, the change takes place only at the rising and falling edges. The
change is instantaneous. This instantaneous rate of change
(dV/dT = dV/0)
will produce an infinitely large output from a differentiator.
Since ideal square or pulse waveforms, as produced by the function generator in Multisim,
have zero rise and fall times, the result of differentiation is infinite (dV/0 = infinity).
In the example circuit, outputs from the differentiator are limited to +/-5 kilo volts. With the
ideal square wave input, the differentiator output will be seen to be +/-5kV.
All real square wave and pulse signals have finite rise times, however small.
To introduce finite rise and fall times into the input to the differentiator, in order to investigate
realistic situations, use an RC network placed in series with the function generator.
Note Since the rise and fall times are fixed, the differentiator output does not change with
change of input frequency as for the sine and triangle waveforms.
Changing the RC time constant and comparing differentiator output will illustrate this point.

Multisim 8 Component Reference Guide 1-39

Source Components

1.33.2 Characteristic Equation

dVi
Vout (t ) = K + VOoff
dt

1.33.3 Voltage Differentiator Parameters and Defaults

Symbol Parameter Name Default Unit

K Gain 1 V/V

VOoff Output offset voltage 0 V

Vl Output voltage lower limit -1e+12 V

Vu Output voltage upper limit 1e+12 V

Vs Upper and lower smoothing range 1e-06 V

1.34 Voltage Integrator

This component calculates the integral of the input voltage (the transfer function, 1/s) and
delivers it to the output. It is used in control systems and analog computing applications.
The true integrator function continuously adds the area under a curve for a specified time
interval.
For waveforms that are symmetrical about the zero axis, area above and below the axis is zero
and the resulting integrator output is zero.
For waveforms that are not symmetrical about the zero axis, the “areas” will be different. If
area above the axis is greater, integrator output will rise. If area is less, integrator output will
fall.

1-40 Electronics Workbench

 Voltage Integrator

1.34.1 Investigations
1. In the initial circuit, the input signal is symmetrical (+/- 5V) about the zero axis and the
integrator output is zero for sine, square and triangle waveforms.
2. To make the waveforms unsymmetrical about the zero axis use the OFFSET control on the
function generator. Setting the OFFSET equal to the AMPLITUDE setting will reference
the input to ground (0V).
In this case, the output is always positive. When output is high, “area” is continually added.
Output will rise indefinitely.
Changing frequency changes the area. Therefore, in the case of lower frequencies, output rises
faster.

1.34.2 Characteristic Equation

( )
t
Vout (t ) = K ∫ Vi (t ) + VIoff dt + VOic
0

Multisim 8 Component Reference Guide 1-41

Source Components

1.34.3 Voltage Integrator Parameters and Defaults

Symbol Parameter Name Default Unit

VIoff Input offset voltage 0 V

K Gain 1 V/V

Vl Output voltage lower limit -1e+12 V

Vu Output voltage upper limit 1e+12 V

Vs Upper and lower smoothing range 1e-06 V

VOic Output initial conditions 0 V

1.35 Voltage Hysteresis Block

This component is a simple buffer stage that provides hysteresis of the output with respect to
the input. ViL and ViH specify the center voltage or current inputs about which the hysteresis
effect operates. The output values are limited to VoL and VoH. The hysteresis value, H, is
added to ViL and ViH in order to specify the points at which the slope of the hysteresis
function would normally change abruptly as the input transitions from low to high values. The
slope of the hysteresis function is smoothly varied whenever ISD is set greater than zero.
This component can be used to simulate a non-inverting comparator in which the comparison
threshold is changed each time the input crosses the threshold in effect at that instant. As the
output changes state (high to low or low to high), the threshold voltage is changed internally
in such a manner that the input must continue to change until it reaches the new threshold.
In the example circuit shown below, the hysteresis value is set to 5V. This means that the two
comparison thresholds at which the output changes are +5V and -5V.
As shown, the input triangle waveform rises from 0V and the output is at its lowest value (0V
in this case), as the input crosses +5V (the upper threshold in comparator terms) the output

1-42 Electronics Workbench

 Voltage Hysteresis Block

changes to its highest value(+2V in this case). Internally in the hysteresis block the threshold
is now changed to -5V, (the lower threshold).
The output continues to rise to a peak and then starts to decrease.
Note The output changes only when the input crosses -5V. Internally, the threshold is
changed again to the upper threshold and the process repeats.

1.35.1 Hysteresis Block Parameters and Defaults

Symbol Parameter Name Default Unit

ViL Input low value 0 V

ViH Input high value 1 V

H Hysteresis 0.1 -

VoL Output lower limit 0 V

VoH Output upper limit 1 V

ISD Input smoothing domain % 1 -

Multisim 8 Component Reference Guide 1-43

Source Components

1.36 Voltage Limiter

This is a voltage “clipper”. The output voltage excursions are limited, or clipped, at
predetermined upper and lower voltage levels while input-signal amplitude varies widely.
In the example shown below, the upper voltage limit is set to +5V and the lower limit is set to
- 5 volts. These settings provide symmetrical clipping on the positive and negative peak
excursions of the input waveform when these peaks exceed the set limit (clipping) values.
The 10 v RMS (14.14v peak) input is limited at +/-5V.
Note If the input peak voltages are within the set limiting voltages, the input signal is passed
through the limiter circuit undistorted.
Unsymmetrical clipping is selected by setting the limit voltages to different values (i.e. +5V
and -2V). This technique may be used to produce non-standard waveshapes, starting with
sine, triangle sawtooth and other symmetrical waveforms.

1-44 Electronics Workbench

 Current Limiter Block

1.36.1 Characteristic Equation

VOUT = K (Vin + VIoff ) for Vmin ≤ Vout ≤ Vmax

VOUT = Vmax for VOUT > Vmax
VOUT = Vmin for VOUT < Vmin

1.36.2 Voltage Limiter Parameters and Defaults

Symbol Parameter Name Default Unit

VIoff Input offset voltage 0 V

K Gain 1 V/V

Vl Output voltage lower limit 0 V

Vu Output voltage upper limit 1 V

Vs Upper and lower limit smoothing range 1e-06 V

1.37 Current Limiter Block

This component models the behavior of an operational amplifier or comparator at a high level
of abstraction. All of its pins act as inputs; three of them also act as outputs. The component
takes as input a voltage value from the “in” connector. It then applies the offset and gain, and
derives from it an equivalent internal voltage, Veq, which it limits to fall between the positive
and negative power supply inputs. If Veq is greater than the output voltage seen on the “out”
connector, a sourcing current will flow from the output pin. Otherwise, if Veq is less than the
output voltage, a sinking current will flow into the output pin.

Multisim 8 Component Reference Guide 1-45

Source Components

Depending on the polarity of the current flow, either a sourcing or a sinking resistance (Rsrc
or Rsnk) value is applied to govern the output voltage/output current relationship. The chosen
resistance will continue to control the output current until it reaches a maximum value
specified by either ISrcL or ISnkL. The latter mimics the current limiting behavior of many
operational amplifier output stages.
During operation, the output current is reflected either in the positive or the negative power
supply inputs, depending on the polarity of the output current. Thus, realistic power
consumption as seen in the supply rails is modeled.
ULSR controls the voltage below positive input power and above negative input power
beyond which Veq = k (input voltage + Off) is smoothed. ISrcSR specifies the current below
ISrcL at which smoothing begins, and specifies the current increment above zero input current
at which positive power begins to transition to zero. ISnkSR serves the same purpose with
respect to ISnkL and negative power. VDSR specifies the incremental value above and below
(Veq - output voltage) = 0 at which output resistance will be set to Rsrc and Rsnk, respectively.
For values of (Veq - output voltage) less than VDSR and greater than -VDSR, output
resistance is interpolated smoothly between Rsrc and Rsnk.
The current limiter block is also a representation of an operational amplifier with respect to
the sourcing and sinking of current at the output and supply terminals.
If the current being sinked/sourced to the load is less than the rated maximum, as determined
from rated maximum sink/source specifications for a particular opamp, operation of the
opamp circuit will be as expected.
If the current to be sinked/sourced is greater than the rated maximum, as determined by a
larger than normal input to the opamp circuit, the current limiter will limit current to the
specified safe maximum value, thus protecting the opamp and associated circuitry from
damage.
In the example circuit shown below, the sink and source current limits are set to 2 mA and the
circuit gain (K) is set to 1. For this case, output current should then be Iload = Vin*K/Rload.
The switch, activated by pressing S, applies either a positive or negative input to the 'op-amp'
circuit. These input levels are such that the output current would be in excess of the rated
value of 2.0mA. The current limit function limits the source or sink output to 2.0 mA.
If the input levels are reduced to 2V or less, then the output current will be as expected at Vin/
Rload.

1-46 Electronics Workbench

 Current Limiter Block

A sine wave input of 1.4v RMS or less will be passed undistorted through the “amplifier”
while inputs greater than 1.4 v RMS will show limiting (clipping) at the peaks.

1.37.1 Current Limiter Parameters and Defaults

Symbol Parameter Name Default Unit

Off Input offset 0 V

k Gain 1 V/V

Rsrc Sourcing resistance 1 Ω

Rsink Sinking resistance 1 Ω

ISrcL Current sourcing limit 10 mA

ISnkL Current sinking limit 10 mA

ULSR Upper and lower power supply smoothing range 1 µV

ISrcSR Sourcing current smoothing range 1 nA

ISnkSR Sinking current smoothing range 1 nA

VDSR Internal/external voltage delta smoothing range 1 νΩ

Multisim 8 Component Reference Guide 1-47

Source Components

1.38 Voltage-Controlled Limiter

A voltage “clipper”. This component is a single input, single output function. The output is
restricted to the range specified by the output lower and upper limits. Output smoothing
occurs within the specified range. The voltage-controlled limiter will operate in DC, AC and
transient analysis modes.
The component tests the values of the upper and lower limit control inputs to make sure that
they are spaced far enough apart to guarantee the existence of a linear range between them.
The range is calculated as the difference between (upper limit control input (U) - VoUD -
ULSR) and (lower limit control input (L) + VoLD + ULSR) and must be greater than or equal
to zero.
The limiting levels may be individually set at fixed values or one or both limiting levels may
be controlled by a variable voltage, depending on the desired application.
In the circuit shown below, the upper voltage limit is set by adjusting the potentiometer
supplying the Upper terminal on the VCL. The lower voltage limit is set by adjusting the
potentiometer supplying the Lower terminal on the VCL. The potentiometers are adjusted by
pressing U or SHIFT-U for the upper limit and L or SHIFT-L for the lower limit.

1-48 Electronics Workbench

 Voltage-Controlled Limiter

These settings may be adjusted to provide symmetrical or unsymmetrical clipping on the

positive and negative peak excursions of the input waveform when these peaks exceed the set
limit (clipping) values.

1.38.1 Voltage-Controlled Limiter Parameters and

Defaults

Symbol Parameter Name Default Unit

ViOff Input offset 0 V

k Gain 1 V/V

VoUD Output upper delta 0 V

VoLD Output lower delta 0 V

ULSR Upper and lower smoothing range 1 µV

Multisim 8 Component Reference Guide 1-49

Source Components

1.39 Voltage Slew Rate Block

This component limits the absolute slope of the output, with respect to time, to some
maximum or value. You can accurately model actual slew rate effects of over-driving an
amplifier circuit by cascading the amplifier with this component. Maximum rising and falling
slope values are expressed in volts per second.
The slew rate block will continue to raise or lower its output until the difference between
input and output values is zero. After, it will resume following the input signal unless the
slope again exceeds its rise or fall slope limits.
This component provides for introduction of selectable rising and falling slew rates (rise and
fall times on a pulse waveform) for analysis of pulse and analog circuits.
With an ideal pulse or analog input to block the effect of slew rate on a logic circuit or analog
amplifier, (discrete component or op-amp) output may be investigated.
In the example shown below, the function generator may be set for either square wave or sine
wave output.
A slew rate of 8000V/sec for rising slope and 6000V/sec for falling slope shows as rise and
fall time on an ideal 80Hz. square wave input. Signal degradation as a result of slew rate
occurs when frequency is increased.
Switching the function generator to sine wave output 60 Hz. does not result in distortion.
However, as frequency is increased, slew rate distortion on a sine wave will become evident at
200 Hz. and above. As frequency is increased, the sine wave deteriorates to a triangle shape.

1-50 Electronics Workbench

 Voltage Slew Rate Block

A more serious degradation of output as a result of slew rate occurs when the input frequency
is doubled to 200Hz.

1.39.1 Voltage Slew Rate Block Parameters and Defaults

Symbol Parameter Name Default Unit

RSMax Maximum rising slope value 1 GV/s

FSMax Maximum falling slope value 1 GV/s

Multisim 8 Component Reference Guide 1-51

Source Components

1.40 Three-Way Voltage Summer

This component is a math functional block that receives up to three voltage inputs and
delivers an output equal to their arithmetic sum. Gain for all three inputs as well as the
summed output may be set to match any three input summing application.
In the example shown below, all gains are set to unity.
The summer may be used to illustrate the result of adding harmonically related sine wave
components which make up a complex waveform (the first three terms in the Fourier
expression defining the waveform).
In the example, a fundamental frequency of 60 Hz. and the third and fifth harmonics (in
phase) may be progressively added to illustrate the basic makeup of a square wave.
Amplitude and phase of any of the signals may be varied to experiment further.

Caution The switches should not be operated while a solution is in

progress. This will result in solution error messages. Allow the
solution to pause (or pause it by clicking on the solution switch).
Operate a switch to add the desired harmonic, and then solve the
circuit again.

1-52 Electronics Workbench

 Three-Way Voltage Summer

1.40.1 Charactistic Equation

VOUT = KOUT[ KA(VA + VAoff ) + KB (VB + VBoff )

+ KC (VC + VCoff )] + V 0off

Multisim 8 Component Reference Guide 1-53

Source Components

1.40.2 Summer Parameters and Defaults

Symbol Parameter Name Default Unit

VAoff Input A offset voltage 0 V

VBoff Input B offset voltage 0 V

VCoff Input C offset voltage 0 V

Ka Input A gain 1 V/V

Kb Input B gain 1 V/V

Kc Input C gain 1 V/V

Kout Output gain 1 V/V

VOoff Output offset voltage 0 V

1.41 Three Phase Delta

This component provides a 3 phase power source. The 3 output pins provide 120 degree phase
shifted output. The user can define the amplitude, frequency, and delay time. This part is used
predominantly in Power applications. The 3 sine wave sources are configured in a delta type
connection.

1.42 Three Phase Wye

This component provides a 3 phase power source. The user can define the amplitude,
frequency, and delay time. The foUrth connection (out the opposite side of the symbol) is
used as a Neutral connection. (to ground, or as a return line for unbalanced loads.)

1-54 Electronics Workbench

 Thermal Noise Source

1.43 Thermal Noise Source

The Thermal Noise Source uses a Gaussian White Noise model to simulate thermal noise
(also known as Johnson noise) in a conductor. It can be placed in series with a resistor to
emulate the thermal noise generated by that resistor.
Thermal Noise results from charges bound to thermally vibrating molecules, which produce
EMF (electro-motive force) at the open terminals of a conductor.
One disadvantage of using a Gaussian White Noise model for this purpose is that its power
would be infinite, however, the model is valid over a limited bandwidth (B) as all EMF
fluctuations outside of the defined bandwidth are ignored.
The rms voltage associated with Johnson Noise in a resistor R, at the temperature T (Kelvin)
over a bandwidth B (in Hertz) is given by the equation:
Vrms (B) = (4kTRB)^1/2 volts, where k = Boltzmann’s Constant = 1.38 e-23 j/d)

The mean power over a bandwidth B is given by the equation:

Power (B) = 4kTRB watts
To set up the Thermal Noise Source, input the required parameters in the Value tab of the
component’s properties dialog box. (Double-click on the placed component to access the
dialog box).

Multisim 8 Component Reference Guide 1-55

Source Components

1-56 Electronics Workbench

Chapter 2
Basic Components

2.1 Connectors

Connectors are mechanical devices used to provide a method of inputting and outputting
signals to a design. They do not affect the simulation of the circuit but are included in the
circuit for the design of the PCB.

2.2 Rated Virtual Components

This component family contains a number of virtual components that can be rated to “blow” if
pre-set tolerance(s) are exceeded when the circuit is simulated. These tolerances are set in the
Values tab of each component’s properties window.
The rated virtual components are:
• BJT_NPN
• BJT_PNP
• Capacitor
• Diode
• Fuse

Multisim 8 Component Reference Guide 2-1

Basic Components

• Inductor
• Motor
• NC Relay
• NO Relay
• NONC Relay
• Resistor

2.3 Sockets

Sockets are mechanical devices that are used to connect devices onto a PCB. They do not
affect the simulation of the circuit but are included for the design of the PCB.

2.4 Switch

The single-pole, double-throw switch can be closed or opened (turned on or off) by pressing a
key on the keyboard. You specify the key that controls the switch by typing its name in the
Value tab of the Circuit/Component Properties dialog box. For example, if you want the
switch to close or open when the spacebar is pressed, type space in the Value tab, then click
OK.
A list of possible key names is shown below.

To use... Type

letters a to z the letter (e.g. a)

Enter enter

spacebar space

2-2 Electronics Workbench

 Resistor

2.5 Resistor

Resistors come in a variety of sizes, depending on the power they can safely dissipate. A
resistor’s resistance, R, is measured in ohms. It can have any value from Ω to MΩ.
The Resistance, R, of a resistor instance is calculated using the following equation:
R = Ro * { 1 + TC1*(T - To) + TC2*[(T-To)^2] }
where:

R = The resistance of the resistor

Ro = The resistance of the resistor at temperature To

To = Normal temperature = 27 degrees C [CONSTANT]

TC1 = First order temperature coefficient

TC2 = Second order temperature coefficient

T = Temperature of the resistor

All of the above variables can be modified, with the exception of To, which is a constant.
Note that Ro is the resistance specified on the Value tab of the resistor properties dialog, not
“R”.
T can be specified in two ways:
1. Select the “Use global temperature” option on the Analysis Setup tab of the resistor
properties dialog box. Specify the (Global) “Simulation temperature (TEMP)” on the
Analysis Options dialog box.
2. Deselect the “Use global temperature” option on the Analysis Setup tab of the resistor
properties dialog box. Specify the local temperature of the resistor instance on the
Analysis Setup tab of the resistor properties dialog.
The resistor is ideal, with the temperature co-efficient set to zero. To include resistors in the
Temperature Analysis, set the temperature co-efficient “TC1 and TC2” in the resistor
properties dialog box.
Resistor tolerance is, by default, set to the global tolerance (defined in the Analysis/Monte
Carlo dialog box). To set the tolerance explicitly, de-select “Use global tolerance” and enter a
value in the “resistance tolerance” field.

Multisim 8 Component Reference Guide 2-3

Basic Components

2.5.1 Resistor: Background Information

Resistors come in a variety of sizes, related to the power they can safely dissipate. Color-
coded stripes on a real-world resistor specify its resistance and tolerance. Larger resistors
have these specifications printed on them.
Any electrical wire has resistance, depending on its material, diameter and length. Wires that
must conduct very heavy currents (ground wires on lightning rods, for example) have large
diameters to reduce resistance.
The power dissipated by a resistive circuit carrying electric current is in the form of heat.
Circuits dissipating excessive energy will literally burn up. Practical circuits must take power
capacity into account.

2.5.2 About Resistance

Ohm's law states that current flow depends on circuit resistance:
I = E/R
Circuit resistance can be calculated from the current flow and the voltage:
R = E/I
Circuit resistance can be increased by connecting resistors in series:
R = R1 + R2 +...+ Rn
Circuit resistance can be reduced by placing one resistor in parallel with another:
1
R = -----------------
1 1 1
--- + --- + ---
R1 R2 R3

2.5.3 Characteristic Equation

The current through the resistor uses the model:
V1−V2
i=
R

2-4 Electronics Workbench

 Capacitor

where

i = current

V1 = voltage at node 1

V2 = voltage at node 2

R = resistance

2.5.4 Resistor Virtual

This component functions in the same way as a resistor, but has a user settable value.

2.6 Capacitor

A capacitor stores electrical energy in the form of an electrostatic field. Capacitors are widely
used to filter or remove AC signals from a variety of circuits. In a DC circuit, they can be used
to block the flow of direct current while allowing AC signals to pass.
A capacitor’s capacity to store energy is called its capacitance, C, which is measured in
farads. It can have any value from pF to mF.
Capacitor tolerance is, by default, set to the global tolerance (defined in the Analysis/Monte
Carlo dialog box). To set the tolerance explicitly, de-select “Use global tolerance” and enter a
value in the “capacitance tolerance” field.
The variable capacitor is simulated as an open circuit with a current across the capacitor
forced to zero by a large impedance value.
The polarized capacitor must be connected with the right polarity. Otherwise, an error
message will appear.Its capacitance, measured in farads, can be any value from pF to F.

Multisim 8 Component Reference Guide 2-5

Basic Components

2.6.1 Capacitor: Background Information

Capacitors in an AC circuit behave as “short circuits” to AC signals. They are widely used to
filter or remove AC signals from a variety of circuits--AC ripple in DC power supplies, AC
noise from computer circuits, etc.
Capacitors prevent the flow of direct current in a DC circuit. They can be used to block the
flow of DC, while allowing AC signals to pass. Using capacitors to couple one circuit to
another is a common practice.
Capacitors take a predictable time to charge and discharge and can be used in a variety of
time-delay circuits. They are similar to inductors and are often used with them for this
purpose.
The basic construction of all capacitors involves two metal plates separated by an insulator.
Electric current cannot flow through the insulator, so more electrons pile up on one plate than
the other. The result is a difference in voltage level from one plate to the other.

2.6.2 Characteristic Equation

The current through the capacitor is equal to C multiplied by the rate of change in voltage
across the capacitor, that is:
dv
i=C
dt

2.6.3 DC Model
In the DC model, the capacitor is represented by an open circuit.

2.6.3.1 Time-Domain Model

Rcn is an equivalent resistance and icn is an equivalent current source. The expression for the Rcn
and icn depends on the numerical integration method used.
For trapezoid method:
h
Rcn =
2C
2C
icn = Vn + in
h

2-6 Electronics Workbench

 Capacitor

For the first-order Gear method Backward Euler:

h
Rcn =
C
C
icn = Vn
h
where

Vn+1 = present unknown voltage

across the capacitor

in+1 = present unknown current

through the capacitor

Vn, in = previous solution values

h = time step

n = time interval

These expressions are derived by applying appropriate numerical integration to the

characteristic equation of the capacitor.

2.6.4 AC Frequency Model

For the small-signal analysis, the capacitor is modeled by an impedance whose imaginary
component is equal to:
1
2πfC

where

f = frequency of operation

C = apacitance value

Multisim 8 Component Reference Guide 2-7

Basic Components

2.6.5 Capacitor Virtual

This component performs the same functions as a capacitor, but has a user settable value.

2.7 Inductor

An inductor stores energy in an electromagnetic field created by changes in current through it.
Its ability to oppose a change in current flow is called inductance, L, and is measured in
henrys. An inductor can have any value from µH to H.
Inductor tolerance is, by default, set to the global tolerance (defined in the Analysis/Monte
Carlo dialog box). To set the tolerance explicitly, de-select “Use global tolerance” and enter a
value in the “inductance tolerance” field.
The variable inductor acts exactly like a regular inductor, except that its setting can be
adjusted. It is simulated as an open circuit with a current across the inductor forced to zero by
a large impedance value. Values are set in the same way as for the potentiometer.
Note This model is ideal.To model a real-world inductor, attach a capacitor and a resistor in
parallel with the inductor.

2.7.1 Inductor: Background Information

An inductor is a coil of wire of one “turn” or more. It reacts to being placed in a changing
magnetic field by developing an “induced” voltage across the turns of the inductance, and will
provide current to a load across the inductance. Voltages can be very large.
Inductors, like capacitors, store energy in magnetic fields. Their “charge” and “discharge”
times make them useful in time-delay circuits.
Electric transformers take advantage of the transfer of energy in a magnetic field from the
primary winding to the secondary winding, using induced voltage and current. The transfer is
proportional to the ratio of the winding turns.

2-8 Electronics Workbench

 Inductor

Radio antennae are inductors that operate like transformers in generating and detecting
electromagnetic fields. Their efficiency is proportional to their size.
The ignition coil in an automobile develops a very high induced voltage when the current
through it suddenly becomes very great. This is the voltage that fires spark plugs.

2.7.2 Characteristic Equation

The voltage across the inductor is equal to the inductance, L, multiplied by the change in
current through the inductor, that is:
di
v=L
dt

2.7.3 DC Model
In the DC model, the inductor is represented by a short circuit.

2.7.4 Time-Domain Model

RLn is an equivalent resistance and iLn is an equivalent current source. The expression for the
RLn and iLn depends on the numerical integration method used.
For trapezoid method:

2L
RLn =
h
h
iLn = Vn + in
2L
For Gear method (first order):
L
RLn =
h
h
iLn = Vn
L

Multisim 8 Component Reference Guide 2-9

Basic Components

where:

Vn+1 = present unknown voltage

across the inductor

in+1 = present unknown current

through the inductor

Vn, in = previous solution values

h = time step

n = time interval

These expressions are derived by applying appropriate numerical integration to the

characteristic equation of the inductor.

2.7.5 AC Frequency Model

For the small-signal analysis, the inductor is modeled by an impedance with its imaginary
component equal to 2πfL,
where

f = frequency of operation of the

circuit

L = inductance value

2.7.6 Inductor Virtual

This component performs in the same way as an inductor, but has a user settable value.

2-10 Electronics Workbench

 Transformer

2.8 Transformer

The transformer is one of the most common and useful applications of inductance. It can step
up or step down an input primary voltage (V1) to a secondary voltage (V2). The relationship
is given by V1/V2 = n, where n is the ratio of the primary turns to the secondary turns. The
parameter n can be adjusted by editing the transformer's model.
To properly simulate the transformer, both sides must have a common reference point, which
may be ground. The transformer can also be used in a center-tapped configuration. A center-
tap is provided which may be used for this purpose. The voltage across the tap is half of the
total secondary voltage.
This transformer is suitable for getting quick results. To simulate realistic devices that include
a transformer, you should use the nonlinear transformer.
Note Both sides of a transformer must be grounded.

2.8.1 Characteristic Equation

The characteristic equation of an ideal transformer is given by:
V1 = nV2
1
i1 = i2
n
where

V1 = primary voltage

V2 = secondary voltage

n = turns ratio

i1 = primary current

i2 = secondary current

Multisim 8 Component Reference Guide 2-11

Basic Components

2.8.2 Ideal Transformer Model Parameters and Defaults

Symbol Parameter Name Default Unit

n Turns ratio 2 -

Le Leakage inductance 0.001 H

Lm Magnetizing inductance 5 H

Rp Primary winding resistance 0.0 W

Rs Secondary winding resistance 0.0 W

If n > 1, it is a step-down transformer; if n < 1, it is a step-up transformer.

2.9 Nonlinear Transformer

This component is based on a general model that can be customized for different applications.
It is implemented using a conceptual magnetic core and coreless coil building blocks, together
with resistors and inductors. Using this transformer, you can model physical effects such as
nonlinear magnetic saturation, primary and secondary winding losses, primary and secondary
leakage inductances, and core geometric size.
See the “Magnetic Core” description for characteristic equations of the magnetic core.

2.9.1 Customizing
The nonlinear transformer can be customized for different applications. It is implemented by
using a magnetic core and the coreless coil as the basic building blocks. The magnetic core
takes in an input voltage and converts it to a Magnetomotive Force (mmf). The Magnetic
Field Intensity (H) is calculated by dividing the mmf by the Length of the core:
H = mmf/L

2-12 Electronics Workbench

 Nonlinear Transformer

H is then used to find the corresponding Flux Density (B). This is done by using the linear
relationship described in the H-B array of coordinate pairs. This H-B array can be taken from
the averaging H-B curve, which may be obtained from a technical manual that specifies the
magnetic characteristics of different cores.
The slope of the B-H function is never allowed to change abruptly, but is smoothly varied
whenever the Input Smoothing domain parameter is set to a number greater than zero.
The Flux Density (B) is multiplied by the cross-sectional area to obtain a Flux Value. The
Flux Value is used by the coreless coil to obtain a value for the voltage reflected back across
the terminals.
The core is modeled to be lossless. No core losses are considered. In the transformer model,
the only losses taken into account are the ones modeled by the winding resistances.
To obtain the H-B points of the curve:
• Contact a manufacturing company. They many be able to provide the technical data
required to model a core.
• Obtain experimental data.

2.9.2 Nonlinear Transformer Parameters and Defaults

Symbol Parameter Name Default Unit

N1 Primary turns 1 -

R1 Primary resistance 1e-06 W

L1 Primary leakage inductance 0.0 H

N2 Secondary turns 1 -

R2 Secondary resistance 1e-06 W

L2 Secondary leakage inductance 0.0 H

A Cross-sectional area 1.0 m2

L Core length 1.0 m

ISD Input smoothing domain 1.0% -

N Number of co-ordinates 2

H1 Magnetic field co-ordinate 1 0 A*turns/m

Multisim 8 Component Reference Guide 2-13

Basic Components

Symbol Parameter Name Default Unit

H2 Magnetic field co-ordinate2 1.0 A*turns/m

H3-H15 Magnetic field co-ordinates 0 A*turns/m

B1 Flux density co-ordinate 1 0 Wb/m2

B2 Flux density co-ordinate 2 1.0 Wb/m2

B3-B15 Flux density co-ordinates 0 Wb/m2

2.10 Relay

The magnetic relay can be used as a normally open or normally closed relay. It is activated
when the current in the energizing circuit (attached to P1, P2) exceeds the value of the switch-
on current (Ion). During operation, the contact switches from the normally closed terminals
(S1, S3) to the normally open terminals (S1, S2). The relay will remain on as long as the current
in the circuit is greater than the holding current (Ihd). The value of Ihd must be less than that of
Ion.
The magnetic relay is a coil with a specified inductance (Lc, in henries) that causes a contact
to open or close when a specified current (Ion, in A) charges it.
The contact remains in the same position until the current falls below the holding value (Ihd,
in A), at which point it returns to its original position.

2.10.1 Model
The energizing coil of the relay is modeled as an inductor, and the relay’s switching contact is
modeled as resistors R1 and R2.

2-14 Electronics Workbench

 Variable Capacitor

2.10.2 Characteristic Equation

R1 =0

R2 =• if ip ≤ ion

R1 =•

R2 =0 if ihd < ion ≤ ip

where

L = inductance of the relay energizing coil, in henrys

R1, R2 = resistance of the relay’s switching contact, in ohms

ion = turn-on current, in amperes

ihd = holding current, in amperes

ip = current through the energizing coil in amperes

2.11 Variable Capacitor

2.11.1 The Component

This component acts much like a regular capacitor, except that its setting can be adjusted.

Multisim 8 Component Reference Guide 2-15

Basic Components

2.11.2 Characteristic Equation and Model

This component’s capacitance, C, is computed based on the initial settings according to the
equation:
Setting
C= * Capacitance
100
The variable capacitor is simulated as an open circuit with a current across the capacitor
forced to zero by a large impedance value.
Values are set in the same way as those for the potentiometer.

2.11.3 Virtual Variable Capacitor

This component performs the same functions as a variable capacitor, but has a user settable
value.

2.12 Variable Inductor

2.12.1 The Component

This component acts much like a regular inductor, except that its setting can be adjusted.

2.12.2 Characteristic Equation and Model

This component’s inductance, L, is computed based on the initial settings according to the
equation:
Setting
L= * Inductance
100

2-16 Electronics Workbench

 Potentiometer

The variable inductor is simulated as an open circuit with a current across the inductor forced
to zero by a large impedance value.
Values are set in the same way as for the potentiometer.

2.12.3 Virtual Variable Inductor

This component performs the same functions as a variable inductor, but has a user settable
value.

2.13 Potentiometer

2.13.1 The Component

This component acts much like a regular resistor, except that you can, with a single keystroke,
adjust its setting. In the Value tab of the Circuit/Component Properties dialog box, you set the
potentiometer’s resistance, initial setting (as a percentage) and increment (as a percentage).
You also identify the key (A to Z) that you will use to control the setting.

To decrease the potentiometer’s setting, press the identified key.

To increase the setting, press and hold SHIFT and press the identified key.
For example, say the potentiometer is set to 45%, the increment is 5% and the key is R. You
press R , and the setting drops to 40%. You press R again, and it drops to 35%. You press SHIFT
and R, and the setting rises to 40%.

Multisim 8 Component Reference Guide 2-17

Basic Components

2.13.2 Characteristic Equation and Model

The potentiometer is simulated using two resistors, R1 and R2, whose values are computed
using the potentiometer’s initial settings.

Setting
r= * Resistance
100

where

R1 = r

R2 = Resistance – r

2.13.3 Virtual Potentiometer

This component performs the same functions as a potentiometer, but has a user settable value.

2.14 Pullup

This component is used to raise the voltage of a circuit to which it is connected. One end is
connected to Vcc. The other end is connected to a point in a logic circuit that needs to be
raised to a voltage level closer to Vcc.

2.15 Resistor Packs

2-18 Electronics Workbench

 Magnetic Core

Resistor packs are collections of resistors within a single package. The configuration of the
resistors can be varied based on the intended usage of the package. Resistor packs are used to
minimize the amount of space required on the PCB for the design. In some applications, noise
can be a consideration for the use of resistor packs.

2.16 Magnetic Core

This component is a conceptual model that you can use as a building block to create a wide
variety of inductive and magnetic circuit models. Typically, you would use the magnetic core
together with the coreless coil to build up systems that mock the behavior of linear and
nonlinear magnetic components. It takes as input a voltage which it treats as a magnetomotive
force (mmf) value.

2.16.1 Characteristic Equation

Magnetic field intensity, H, is:

H = mmf / l

where

mmf = magnetomotive force, the input voltage

l = core length

Flux density, B, is derived from a piecewise linear transfer function described to the model by
the (magnetic field, flux density) pairs that you input in the Circuit/Component Properties
dialog box. The final current, I, allowed to flow through the core is used to obtain a value for
the voltage reflected back across the terminals. It is calculated as:

I = BA

Multisim 8 Component Reference Guide 2-19

Basic Components

where

A = cross-sectional area

2.16.2 Magnetic Core Parameters and Defaults

Symbol Parameter Name Default Unit

A Cross-sectional area 1 m2

L Core length 1 m

ISD Input smoothing domain% 1 -

N Number of co-ordinates 2 -

H1 Magnetic field co-ordinate 1 0 A*turns/m

H2 Magnetic field co-ordinate 2 1.0 A*turns/m

H3-H15 Magnetic field co-ordinates 0 A*turns/m

B1 Flux density co-ordinate 1 0 Wb/m2

B2 Flux density co-ordinate 2 1.0 Wb/m2

B3-B15 Flux density co-ordinates 0 Wb/m2

2.17 Coreless Coil

This component is a conceptual model that you can use as a building block to create a wide
variety of inductive and magnetic circuit models. Typically, you would use the coreless coil
together with the magnetic core to build up systems that mock the behavior of linear and
nonlinear magnetic components. It takes as input a current and produces a voltage. The output

2-20 Electronics Workbench

 Z Loads

voltage behaves like a magnetomotive force in a magnetic circuit, that is, when the coreless
coil is connected to the magnetic core or some other resistive device, a current flows.

2.17.1 Characteristic Equation

Vout = N ∗ iin
where

Vout = output voltage value

(magnetomotive force)

iin = input current

2.17.2 Coreless Coil Parameters and Defaults

Symbol Parameter Name Default Unit

N Number of inductor turns 1 -

2.18 Z Loads

2.18.1 A+jB Block

The A+jB Block is a circuit block with resistance and inductance connected in series.
“A” is resistance, “B” is inductive reactance (XL) at a specified frequency and j 2 = −1 .
XL = 2πfL , where f is the specified frequency and L is the inductance.

Multisim 8 Component Reference Guide 2-21

Basic Components

2.18.2 A-jB Block

The A- jB Block is a circuit block with resistance and capacitance connected in series.
“A” is resistance, “B” is capacitive reactance (XC) at a specified frequency and j 2 = −1 .
1
XC =
2πfC
where f is the specified frequency and C is the capacitance.

2.18.3 Z Load 1

Z Load 1 is a circuit block with values of R, L and C as shown.

2.18.4 Z Load 1 Delta

Z Load 1 Delta is a delta connection of three Z Load 1s as shown.

2-22 Electronics Workbench

 Z Loads

2.18.5 Z Load 1 Wye

Z Load 1 Wye is a delta connection of three Z Load 1s as shown.

2.18.6 Z Load 2

Z Load 2 is an RLC series connection block with R, L, and C values as shown.

2.18.7 Z Load 2 Delta

Z Load 2 Delta is a delta connection of three Z Load 2s as shown.

Multisim 8 Component Reference Guide 2-23

Basic Components

2.18.8 Z Load 2 Wye

Z Load 2 Wye is a wye connection of three Z Load 2s as shown.

2.18.9 Z Load 3

Z Load 3 is a circuit block with an RLC parallel connection with R, L and C values as shown.

2-24 Electronics Workbench

Chapter 3
Diodes

3.1 Diode

Diodes allow current to flow in only one direction and can therefore be used as simple solid-
state switches in AC circuits, being either open (not conducting) or closed (conducting).
Terminal A is called the anode and terminal K is called the cathode.

3.1.1 Diodes: Background Information

Diodes exhibit a number of useful characteristics, such as predictable capacitance (that can be
voltage controlled) and a region of very stable voltage. They can, therefore, be used as
switching devices, voltage-controlled capacitors (varactors) and voltage references (Zener
diodes).
Because diodes will conduct current easily in only one direction, they are used extensively as
power rectifiers, converting AC signals to pulsating DC signals, for both power applications
and radio receivers.
Diodes behave as voltage-controlled switches, and have replaced mechanical switches and
relays in many applications requiring remote signal switching.
Even indicator lamps are now replaced with diodes (LEDs) that emit light in a variety of
colors when conducting.
A special form of diode, called a Zener diode, is useful for voltage regulation.

Multisim 8 Component Reference Guide 3-1

Diodes

3.1.2 DC Model
The DC characteristic of a real diode in Multisim is divided into the forward and reverse
characteristics.
DC forward characteristic:
 nV
VD

I D = I S  e T − 1 + VD ∗ Gmin for VD ≥ −5nVT

 

DC reverse characteristic:

  VD 
 I S  e nVT − 1 + V D ∗ Gmin for − 5nVT ≤ V D ≤ 0
  

− I S + V D ∗ Gmin for − BV < V D < −5nVT
ID = 
− IBV for V D = − BV

  −  BV +VD  
− I S  e  VT  − 1 + BV  for V D < − BV
  VT 
 

where

ID = current through the diode, in amperes

VD = voltage across the diode, in volts

VT = thermal voltage (= 0.0258 volts at room

temperature (27°C))

BV = breakdown voltage

IS is equivalent to the reverse saturation current (Io) of a diode. In a real diode, IS doubles for
every 10-degree rise in temperature.
Other symbols used in these equations are defined in “Diode Parameters and Defaults”.

3-2 Electronics Workbench

 Diode

3.1.3 Time-Domain Model

This model defines the operation of the diode, taking into account its charge-storage effects or
capacitance. There are two types of capacitances: diffusion or storage capacitance, and
depletion or junction capacitance.
The charge-storage element, CD, takes into account both of these as follows:
 dI D  V 
-m

τ t + C j 0 1 - D  for VD < FC∗ j0

 dVD  ϕ0 
CD = 
 dI D C j0  mVD 
τ t dVD
+
F2 
 F3 +
ϕ0 
 for VD ≥ FC∗ j0

where

Cj0 = zero-bias junction capacitance; typically 0.1

to 10 picofarads

ϕ0 = junction potential; typically 0.5 to 0.7 volts

τt = transit time; typically 1 nanosecond

m = junction grading coefficient; typically 0.33 to

0.5

and where F2 and F3 are constants whose values are:

F 2 = (1 − FC )1+ m
F 3 = 1 − FC (1 + m)
Notes
1. The voltage drop across the diode varies depending on the set value of:

IS = saturation current; typically 10-14 amperes

rS = ohmic resistance; typically 0.05 ohms.

2. The parameter τt is proportional to the reverse recovery time of the diode. That is, it affects
the turn-off or switching speed of the diode. It is the time required for the minority carrier
to cross the junction.
3. The barrier potential for a diode is approximately 0.7 to 0.8 volts. This is not to be
confused with the model parameter ϕ0 given above.

Multisim 8 Component Reference Guide 3-3

Diodes

3.1.4 AC Small-Signal Model

The figure below shows the linearized, small-signal diode model, in which the diode is
represented by a small-signal conductance, gD. The small-signal capacitance is also evaluated
at the DC operating point.

VD
dID IS nV
gD = OP = e T
dV D nV Τ

  VD 
-m

τ t ∗ gD + C j 0  1 -  for VD < FC∗ j0

dQD   ϕ0 
CD = OP =
dVD  Cj0  mVD 
τ t ∗ gD + F  F3 + ϕ  for VD ≥ FC∗ j0
 2 0

where

OP = operating point

QD = the charge on CD

3.1.5 Diode Parameters and Defaults

Symbol Parameter Name Default Typical Value Unit

IS Saturation current 1e-14 1e-9 - 1e-18 cannot A

be 0

RS Ohmic resistance 0 10 W

CJO Zero-bias junction 0 0.01-10e-12 F

capacitance

VJ Junction potential 1 0.05-0.7 V

TT Transit time 0 1.0e-10 s

M Grading coefficient 0.5 0.33-0.5 -

3-4 Electronics Workbench

 Pin Diode

Symbol Parameter Name Default Typical Value Unit

Symbol Parameter Name Default Typical Value Unit

BV Reverse bias breakdown 1e+30 - V

voltage

N Emission coefficient 1 1 -

EG Activation energy 1.11 1.11 eV

XTI Temperature exponent for 3.0 3.0 -

effect on IS

KF Flicker noise coefficient 0 0 -

AF Flicker noise exponent 1 1 -

FC Coefficient for forward-bias 0.5 0.5 -

depletion capacitance formula

IBV Current at reverse breakdown 0.001 1.0e-03 A

voltage

TNOM Parameter measurement 27 27-50 °C

temperature

3.2 Pin Diode

The PIN diode consists of three semiconductor materials.

The center material is made up of intrinsic (pure) silicon. The p- and n-type materials are
heavily doped and, as a result, have very low resistances.
When reverse biased, the PIN diode acts as a capacitor. The intrinsic material can be seen as
the dielectric of a capacitor. The heavily doped p- and n-type materials can be viewed as the
two conductors.

Multisim 8 Component Reference Guide 3-5

Diodes

3.2.1 Photo Diode Application

The intrinsic layer, which is a pure semiconductor with no impurities, makes the PIN diode
respond better to infrared photons that penetrate deeper into the diode’s regions.
The intrinsic layer creates a larger depletion region, which causes the diode to produce a more
linear change in current in response to changes in light intensity.

3.3 Zener Diode

A zener diode is designed to operate in the reverse breakdown, or Zener, region, beyond the
peak inverse voltage rating of normal diodes. This reverse breakdown voltage is called the
Zener test voltage (Vzt), which can range between 2.4 V and 200 V.
In the forward region, it starts conducting around 0.7 V, just like an ordinary silicon diode. In
the leakage region, between zero and breakdown, it has only a small reverse current. The
breakdown has a sharp knee, followed by an almost vertical increase in current.
Zener diodes are used primarily for voltage regulation because they maintain constant output
voltage despite changes in current.

3.3.1 DC Model
The DC characteristic of a real diode in Multisim is divided into the forward and reverse
characteristics.
DC forward characteristic:

 VD 
I D = I S  e nVT − 1 + VD ∗ Gmin for VD ≥ −5nVT
 

3-6 Electronics Workbench

 Zener Diode

DC reverse characteristic:

  VD 
 I S  e nVT − 1 + V D ∗ Gmin for − 5nVT ≤ VD ≤ 0
  

− I S + V D ∗ Gmin for − BV < VD < −5nVT
ID = 
− IBV for VD = − BV

  −  BV +VD  
− I S  e  VT  − 1 + BV  for VD < − BV
  VT 
 
where

ID = current through the diode in amperes

VD = voltage across the diode in volts

VT = thermal voltage (= 0.0258 volts at room

temperature (27°C))

BV = breakdown voltage

IS is equivalent to the reverse saturation current (Io) of a diode. In a real diode, IS doubles for
every 10-degree rise in temperature.
Other symbols used in these equations are defined in the table below.

3.3.2 Zener Diode Parameters and Defaults

Symbol Parameter name Default Unit

Is Saturation current 1e-14 A

Rs Ohmic resistance 0 W

CJO Zero-bias junction capacitance 0 F

VJ Junction potential 1 V

TT Transit time 0 S

Multisim 8 Component Reference Guide 3-7

Diodes

Symbol Parameter name Default Unit

M Grading coefficient 0.5 -

VZT Zener test voltage 1e+30 V

IZT Zener test current 0.001 A

N Emission coefficient 1 -

EG Activation energy 1.11 eV

XTI Temperature exponent for effect 3.0 -

on Is

Symbol Parameter name Default Unit

KF Flicker noise coefficient 0 -

AF Flicker noise exponent 1 -

FC Coefficient for forward-bias 0.5 -

depletion capacitance formula

TNOM Parameter measurement 27 °C

temperature

3.4 LED (Light-Emitting Diode)

This diode emits visible light when forward current through it, Id, exceeds the turn-on current,
Ion. The electrical model of the LED is the same as the diode model described previously.
LEDs are used in the field of optoelectronics. Infrared devices are used together with
spectrally matched phototransistors in optoisolation couplers, hand-held remote controllers,
and in fiber-optic sensing techniques. Visible spectrum applications include status indicators
and dynamic power level bar graphs on a stereo system or tape deck.

3-8 Electronics Workbench

 LED (Light-Emitting Diode)

3.4.1 Background Information

LEDs are constructed of gallium arsenide or gallium arsenide phosphide. While efficiency
can be obtained when conducting as little as 2 milliamperes of current, the usual design goal is
in the vicinity of 10 mA. During conduction, there is a voltage drop across the diode of about
2 volts.
Most early information display devices required power supplies in excess of 100 volts. The
LED ushered in an era of information display components with sizes and operating voltages
compatible with solid-state electronics. Until the low-power liquid-crystal display was
developed, LED displays were common, despite high current demands, in battery-powered
instruments, calculators and watches. They are still commonly used as on-board annunciators,
displays and solid-state indicator lamps.

3.4.2 LED Parameters and Defaults

Symbol Parameter Name Default Unit

IS Saturation current 1e-14 A

RS Ohmic resistance 0 W

CJO Zero-bias junction capacitance 0 F

VJ Junction potential 1 V

TT Transit time 0 s

M Grading coefficient 0.5 -

Multisim 8 Component Reference Guide 3-9

Diodes

3.5 Full-Wave Bridge Rectifier

The full-wave bridge rectifier uses four diodes to perform full-wave rectification of an input
AC voltage. Two diodes conduct during each half cycle, giving a full-wave rectified output
voltage. The top and bottom terminals can be used as the input terminals for the AC voltage.
The left and right terminals can be used as the output DC terminals.

3.5.1 Characteristic Equation

The average output DC voltage at no load condition is approximately given by:

VDC = 0.636 * (Vp - 1.4)

where

Vp = the peak value of the input AC voltage

3.5.2 Model
A full-wave bridge rectifier consists of four diodes as shown in its icon.
Terminals 1 and 2 are the input terminals, so the input AC source is connected across 1 and 2.
Terminals 3 and 4 are the output terminals, so the load is connected across 3 and 4.
When the input cycle is positive, diodes D1 and D2 are forward-biased and D3 and D4 are
reverse-biased. D1 and D2 thus conduct current in the direction shown. The voltage developed
is identical to the positive half of the input sine wave minus the diode drops.
When the input cycle is negative, diodes D3 and D4 become forward-biased and conduct
current in the direction shown. Hence, the current flows in the same direction for both the
positive and the negative halves of the input wave. A full-wave rectified voltage appears
across the load.

3-10 Electronics Workbench

 Full-Wave Bridge Rectifier

3.5.3 Full-Wave Bridge Rectifier Parameters and

Defaults

Symbol Parameter Name Default Typical Value Unit

IS Saturation current 1e-14 1e-9 - 1e-18 cannot A

be 0

RS Ohmic resistance 0 10 W

CJO Zero-bias junction capacitance 0 0.01-10e-12 F

VJ Junction potential 1 0.05-0.7 V

TT Transit time 0 1.0e-10 s

M Grading coefficient 0.5 0.33-0.5 -

BV Reverse bias breakdown 1e+30 - V

voltage

N Emission coefficient 1 1 -

EG Activation energy 1.11 1.11 eV

XTI Temperature exponent for 3.0 3.0 -

effect on IS

KF Flicker noise coefficient 0 0 -

AF Flicker noise exponent 1 1 -

FC Coefficient for forward-bias 0.5 0.5 -

depletion capacitance formula

IBV Current at reverse breakdown 0.001 1.0e-03 A

voltage

TNOM Parameter measurement 27 27-50 °C

temperature

Multisim 8 Component Reference Guide 3-11

Diodes

3.6 Schottky Diode

The Schottky diode is a two-terminal device with a junction that uses metal in place of the p-
type material. The formation of a junction with a semiconductor and metal results in very little
junction capacitance.
The Schottky diode will have a VF of approximately 0.3 V and a VBR of less than − 50 V.
These are lower than the typical pn-junction ratings of VF = 0.7 V and VBR = −1 50 V.
With very little junction capacitance, the Schottky diode can be operated at much higher
frequencies than the typical pn-junction diode and has a much faster switching time.
The Schottky diode is a relatively high-current device that is capable of switching rapidly
while providing forward currents of approximately 50 A. It can operate at frequencies of 20
GHz and higher in sinosoidal and low-current switching circuits.

3.7 Silicon-Controlled Rectifier

A silicon-controlled rectifier (SCR) is a unidirectional current control device like a Shockley

diode. However, the SCR has a third terminal capable of supporting a digital gate connection,
which adds another means of controlling the current flow. The SCR switches on when the
forward bias voltage exceeds the forward-breakover voltage or when a current pulse is
applied to the gate terminal.
The SCR is triggered into conduction by applying a gate-cathode voltage (VGK), which
causes a specific level of gate current (IG). The gate current triggers the SCR into conduction.
The device is returned to its nonconducting state by either anode current interruption or forced
commutation. When the SCR is turned off, it stays in a non-conducting state until it receives
another trigger.

3-12 Electronics Workbench

 Silicon-Controlled Rectifier

3.7.1 Model
The SCR is simulated using a mixed electrical and behavioral model.
The status of the SCR is handled with a logical variable, much like the Shockley diode and
diac simulations. The resistance, Rs, acts as a current block when the SCR is switched off. Rs
has two separate values, depending on the status of the SCR. When the SCR is on, the
resistance Rs is low; when the SCR is off, the resistance Rs is high. The high resistance value
acts as a current block.
The SCR is switched on and Rs set low (1e-06) if:
Vd ≥ Vdrm
or
Ig ≥ Igt at Vg ≥ Vgt and

Vd ≥ 0
or
dVd dV of the SCR
≥
dt dt

The SCR is switched off and Rs set high if:

Id < Ih
In this case, the switching occurs after turn-off time Tq, which is implemented by the
behavioral controller.

Id = current through the SCR, in amperes

rs = blocking resistance, in ohms

Symbols used in these equations are defined in “SCR Parameters and Defaults”.

3.7.2 Time-Domain Model

For the time-domain model, the charge-storage effects of the SCR junction capacitance are
considered in the simulation.
The turn-off time, Tq, is implemented by introducing a behavioral delay in the opening of the
controlled switch.

Multisim 8 Component Reference Guide 3-13

Diodes

3.7.3 AC Small-Signal Model

In the AC model, the diode is represented by its linearized small-signal model. The diode
small-signal conductance gd and the small-signal capacitance Cd are evaluated at the DC
operating point.

3.7.4 SCR Parameters and Defaults

Symbol Parameter Name Default Unit

Irdm Peak off-state current 1e-06 A

Vdrm Forward breakover voltage 200 V

Vtm Peak on-state voltage 1.5 V

Itm Forward current at which Vtm is measured 1 A

Tq Turn-off time 1.5e-05 s

dv/dt Critical rate of off-state voltage rise 50 V/µs

Ih Holding current 0.02 A

Vgt Gate trigger voltage 1 V

Igt Gate trigger current 0.001 A

Vd Voltage at which Igt is measured 10 V

3.8 DIAC

A diac is a two-terminal parallel-inverse combination of semiconductor layers that allows

triggering in either direction. It functions like two parallel Shockley diodes aligned back-to-
back. The diac restricts current flow in both directions until the voltage across the diac
exceeds the switching voltage. Then the diac conducts current in the direction of the voltage.

3-14 Electronics Workbench

 DIAC

3.8.1 DC Model
The diac is switched on and the resistance, Rs, is set low if, in either the positive or negative
direction.
Vd ≥ Vs
The diac is switched off (current-blocking mode) and Rs is set high if, in either direction:
Vs
I rev
Id < Ih
where

Vd = voltage across the diac, in volts

Id = current through the diac, in amperes

Rs = blocking resistance

Irev = = peak off-state reverse current

Other symbols used in these equations are defined in “Diac Parameters and Defaults”.

3.8.2 Time-Domain and AC Small-Signal Models

Each of the Shockley diodes is simulated with the mixed electrical/behavioral model
described in the DC model above.

Multisim 8 Component Reference Guide 3-15

Diodes

3.8.3 DIAC Parameters and Defaults

Symbol Parameter Name Default Unit

IS Saturation current 1e-06 A

Vs Switching voltage 100 V

Vtm Peak on-state voltage 1.5 V

Itm Forward current at which Vtm is measured 1 A

Tq Turn-off time 1e-06 s

Ih Holding current 0.02 A

CJO Zero-bias junction capacitance 1e-12 F

3.9 TRIAC

A triac is a three-terminal five-layer switch capable of conducting current in both directions.

The triac model consists of two SCRs, each of which is modeled as described earlier in this
chapter. The triac remains off, restricting current in both directions until the voltage across the
triac exceeds the breakover voltage, or until a positive pulse of current is applied to the gate
terminal.

3.9.1 Model
The simulation is a combined electrical/behavioral model. The status of the triac, either on or
off, is treated as a logical variable. The resistance, Rs, is a function of the triac status.

3-16 Electronics Workbench

 TRIAC

When the triac is off, the resistance Rs is set high to act as a current block. When the triac is
on, Rs is low (1e-06).

 V d rm 
 
 I d rm 

The triac is switched on in either direction if:

Vd ≥ Vdrm
Rs = 1e - 06
or
Vd ≥ 0 and
Ig ≥ Igt at Vg ≥ Vgt

dVd dV
or ≥ of the triac
dt dt

The triac is switched off and the resistance Rs is set high (current-blocking mode) if:
Id < Ih.
In this case the switching occurs after turn-off time Tq, which is implemented by the
behavioral controller.

Vs = maximum forward breakover voltage, or switching

voltage, in volts

Id = current through the diac, in amperes

Rs = blocking resistance, in ohms

Irev = peak off-state reverse current

vbr = maximum forward breakover voltage, in volts

id = current through the triac, in amperes

Vd = voltage across the diac, in volts

vd = voltage across the triac, in volts

td = turn-on time, in seconds

Other symbols used in these equations are defined in “Triac Parameters and Defaults”.

Multisim 8 Component Reference Guide 3-17

Diodes

3.10 Varactor Diode

The varactor is a type of pn-junction diode with relatively high junction capacitance when
reverse biased. The capacitance of the junction is controlled by the amount of reverse voltage
applied to the device, which makes the device function as a voltage-controlled capacitor.
The capacitance of a reverse-biased varactor junction is found in the following way:
A
C T = ε -------
Wd

where

CT = the total junction capacitance

Π= permittivity of the semiconductor material

A = the cross-sectional area of the junction

Wd = the width of the depletion layer

The value of CT is inversely proportional to the width of the depletion layer. The depletion
layer acts as an insulator (called the dielectric) between the p-type and n-type materials.
Varactor diodes are used in place of variable capacitors in many applications.

3-18 Electronics Workbench

Chapter 4
Transistors

4.1 BJT (NPN & PNP)

A bipolar junction transistor, or BJT, is a current-based valve used for controlling electronic
current. BJTs are operated in three different modes, depending on which element is common
to input and output: common base, common emitter or common collector. The three modes
have different input and output impedances and different current gains, offering individual
advantages to a designer.
A transistor can be operated in its nonlinear region as a current/voltage amplifier or as an
electronic switch in cutoff and saturation modes. In its linear region, it must be biased
appropriately (i.e., subjected to external voltages to produce a desired collector current) to
establish a proper DC operating point. The transistors' parameters are based on the Gummel-
Poon transistor model.
BJTs are commonly used in amplification and switching applications. They come in two
versions: NPN and PNP. The letters refer to the polarities, positive or negative, of the
materials that make up the transistor sandwich. For both NPNs and PNPs, the terminal with
the arrowhead represents the emitter.
An NPN transistor has two n-regions (collector and emitter) separated by a p-region (base).
The terminal with the arrowhead is the emitter. The ideal NPN in the parts bin has generic
values suitable for most circuits. You can specify a real-world transistor by double-clicking
the icon and choosing another model.
A PNP transistor has two p-regions (collector and emitter) separated by an n-region (base).
The terminal with the arrowhead represents the emitter. The ideal PNP model has generic
values suitable for most circuits. You can specify a real-world transistor by double-clicking
the icon and choosing another model.

Multisim 8 Component Reference Guide 4-1

Transistors

4.1.1 Characteristic Equations

IE = IC + IB
IC
βDC = = hFE
IB
∆IC
βAC = = OP(VCE ) = hfe
∆IB
where

βDC = hFE = DC current gain

βAC = hfe = small-signal current gain

IC = collector current

IB = base current

∆ IE = emitter current

The model for the PNP transistor is the same as the NPN model, except the polarities of the
terminal currents and voltages are reversed.
The DC characteristic of a BJT in Multisim is modeled by a simplified Gummel-Poon model.
The base-collector and base-emitter junctions are described by their ideal diode equations.
The diode capacitors are treated as open circuits.

4-2 Electronics Workbench

 BJT (NPN & PNP)

The beta variation with current is modeled by two extra non-ideal diodes. The diode
capacitors are treated as open circuits. The various equations are:

  VBE  
IBE 2 = ISE exp  − 1
  neVΤ  
  VBC  
IBC 2 = IS exp  − 1
  ncVΤ  
1
Kq1 =
1 − VVABC
IS   VBE  
Kq 2 = exp VΤ  − 1
IKF  
Kqb =
Kq1
2
(
1 + 1 + 4 Kq 2 )

IS   VBE  
I CE = exp  V Τ  − 1
K qb  
IS   VBC  
I CC = exp  V Τ  − 1
K qb  
I CT = I CE − I CC
  VBE  
I B E 1 = I S exp   − 1
  VΤ  
  VBC  
I B C 1 = I S exp   − 1
  VΤ  
where

VT = thermal voltage = 0.0258

VA = forward early voltage

The model parameter βf is equivalent to βDC in the DC case and βAC in the AC case.
Other symbols used in these equations are defined in “BJT Model Parameters and Defaults.”

Multisim 8 Component Reference Guide 4-3

Transistors

4.1.2 Time-Domain Model

The BJT time-domain model takes into account the parasitic emitter, base and collector
resistances, and also the junction, diffusion, and substrate capacitances. The capacitors in the
model are represented by their energy storage model derived using the appropriate numerical
integration rule.
 dI CC  V 
- mE

τ F + C jE 0 1 − BE  for VBE < FC∗ϕ E

 dVBE  ϕE 
CBE =
 dI CC C jE 0  mV 
τ F dVBE
+
F2 
 F3 + E BE 
ϕE 
for VBE ≥ FC∗ϕ E

 dI EC  V 
- mC

τ R + C jC 0 1 − BC  for VBC < FC∗ϕ C

 dVBC  ϕC 
CBC =
 dI EC  mV 
τ R dVBC
+ C jC 0  F3 + C BC 
 ϕC 
for VBC ≥ FC∗ϕ C


  VCS 
-ms

 C js 0  1 −  fo r V C s < 0
  ϕS 
C su b = 
  m sV C S 
 C  1 +  fo r V C s > 0

js 0
 ϕs 

  VBX 
-mC

CjC0 (1- XCJC )1−  for VBX < FC∗ϕC

  ϕC 
CJX = 
CjC0 (1- XCJC )  mCVBX 
 ∗  F +  for VBX ≥ FC∗ϕC
 F2 
3
ϕC 

4-4 Electronics Workbench

 BJT (NPN & PNP)

where, for the base-emitter junction, CBE,

F2 = (1 − FC )
1+ mE

F3 = 1 − FC (1 + mE )
and for the base-collector junction, CBC and CJX,

F2 = (1 − FC )
1+ mC

F3 = 1 − FC(1 + mC )
The symbols used in these equations are defined in “BJT Model Parameters and Defaults.”

4.1.3 AC Small-Signal Model

The small-signal model of a BJT is automatically computed during linearization of the DC
and large-signal time-domain models. The circuit shown is the Gummel-Poon small-signal
model of an NPN transistor.
IB
Cπ = CBE OP gπ = OP
VΤ
IC
Cµ = CBC OP gm = OP
VΤ
Ic
Cs = Csub OP g0 = OP
VA
gm
CJX = CJX OP βac
gπ
ic = gπvbe + gµvce
where

gp = input conductance

gµ = reverse feedback conductance

gm = transductance

go = output conductance.

Multisim 8 Component Reference Guide 4-5

Transistors

4.1.4 BJT Model Parameters and Defaults

Symbol Parameter Name Default Example Unit

IS Saturation current 1e-16 1e-15 A

βF Forward current gain coefficient 100 100 -

βR Reverse current gain coefficient 1 1 -

rb Base ohmic resistance 0 100 W

re Emitter ohmic resistance 0 10 W

rc Collector ohmic resistance 0 1 W

Cs Substrate capacitance 0 1 F

Ce, Cc Zero-bias junction capacitances 0 2e-09 F

φe,φc Junction potentials 0.75 0.75 V

τF Forward transit time 0 1e-13 s

τR Reverse transit time 0 10e-09 s

me, mc Junction grading coefficients 0.33 0.5 -

VA Early voltage 1e+30 200 V

Ise Base emitter leakage saturation 0 1e-13 A

current

Ikf Forward beta high-current knee-point 1e+30 0.01 A

Ne Base-emitter leakage emission 1.5 2 -

coefficient

NF Forward current emission coefficient 1 1 -

NR Reverse current emission coefficient 1 1 -

VAR Reverse early voltage 1e+30 200 V

IKR Reverse beta roll-off corner current 1e+30 0.01 A

ISC B-C leakage saturation current 0 0.01 A

NC B-C leakage emission coefficient 2 1.5 -

4-6 Electronics Workbench

 BJT (NPN & PNP)

Symbol Parameter Name Default Example Unit

IRB Current for base resistance equal to 1e+30 0.1 A

(rb+RBM)/2

RBM Minimum base resistance at high 0 10 W

currents

XTF Coefficient for bias dependence of tF 0 0 -

VTF Voltage describing VBC dependence 1e+30 - V

of tF

ITF High current dependence of tF 0 - A

PTF Excess phase at frequency equal to 1/ 0 - Deg

(tF*2PI) Hz

XCJC Fraction of B-C depletion capacitance 1 - -

connected to internal base node

VJS Substrate junction build-in potential .75 - V

MJS Substrate junction exponential factor 0 0.5 -

XTB Forward and reverse beta temperature 0 - -

exponent

EG Energy gap for temperature effect on 1.11 - eV

IS

XTI Temperature exponent for effect on IS 3 - -

KF Flicker noise coefficient 0 - -

AF Flicker noise exponent 1 - -

FC Coefficient for forward-bias depletion .5 - -

capacitance formula

TNOM Parameter measurement temperature 27 50 °C

Multisim 8 Component Reference Guide 4-7

Transistors

4.2 Resistor Biased BJT (NPN & PNP)

Resistor biased BJTs are discrete transistors which have had additional resistors added to
them within a standard transistor package. This is done to reduce the space required on the
PCB for the design. The general application is for transistor switches for displays such as
LED and Hex displays.
They come in two varieties: with a NPN transistor or a PNP transistor.

4.3 Darlington Transistor (NPN & PNP)

The Darlington connection is a pair of two bipolar junction transistors for operation as a
composite transistor. The composite transistor acts as a single unit with a current gain that is
the product of the current gains of each bipolar junction transistor.
A Darlington array consists of seven Darlington pairs. Each pair has an input and an output.
There is also one Common and one GND pin on the IC.

4-8 Electronics Workbench

 Darlington Transistor (NPN & PNP)

4.3.1 DC Bias Model

If a Darlington transistor with a very high current gain, βD, is used, the base current may be
calculated from
V CC – V BE
I B = ---------------------------
RB + βD RE

This equation is the same for a regular transistor, however, the value of βD is much greater,
and the value of VBE is larger.
The emitter current is then

I E = ( β D + 1 )I B ≈ β D I B

DC voltages are:
VE = IE RE

V B = V E + V BE

4.3.2 AC Model
The AC input signal is applied to the base of the Darlington transistor through capacitor C1,
with the ac output, Vo, obtained from the emitter through capacitor C2. The Darlington
transistor is replaced by an ac equivalent circuit made up of an input resistance, ri, and an
output current source, βDIb.

4.3.2.1 AC Input Impedance

The AC input impedance looking into the transistor base is then
Vi
----- = r i + β D R E
Ib

The AC input impedance looking into the circuit is

Z i = R B || ( r i + β D R E )

Multisim 8 Component Reference Guide 4-9

Transistors

4.3.2.2 AC Current Gain

The AC circuit gain is as follows:

RB βD RB
A i = β D --------------------------- = ---------------------------
RB + βD RE RB + βD RE

4.4 BJT Array

BJT arrays are collections of discrete transistors on a single die. They can come in many
variations based on their intended application. The reasons for using an array is that the
devices are more closely matched than a random group of discrete devices (eliminating the
need to sort them), the noise characteristics are better, and the space required on a PCB is
smaller.
There are three types of BJT arrays:
• PNP transistor array
• NPN/PNP transistor array
• NPN transistor array.

4.4.1 General-purpose PNP Transistor Array

This general-purpose silicon PNP transistor array incorporates two transistors, a Darlington
circuit, and a current-mirror pair with a shared diode.
The two transistors can be used in circuit applications. The total array can be used in
applications in systems with low-power and low-frequency requirements.

4-10 Electronics Workbench

 P-Channel MOSFET

4.4.2 NPN/PNP Transistor Array

This general-purpose high-voltage silicon transistor array consists of five independent
transistors (two PNP and three NPN types) on a common substrate, which has a separate
connection. Separate connection for each transistor permits greater flexibility in circuit
design.
This array is useful in applications including differential amplifiers, DC amplifiers, level
shiftors, timers, thyristor firing circuits and operational amplifiers.

4.4.3 General-purpose High-current NPN Transistor

Array
This array consists of five high-current NPN transistors on a common monolithic substrate.
Two of these transistors are matched at low currents for applications in which offset
parameters are particularly important. Independent connections for each transistor and a
separate terminal for the substrate allow for maximum flexibility in circuit design.
This array is useful in applications such as signal processing and switching systems operating
from DC to VHF. Other applications include lamp and relay driver, differential amplifier,
thyristor firing and temperature-compensated amplifier.

4.5 P-Channel MOSFET

This device is a P-channel MOSFET. See also “MOSFET” on page 4-12.

4.6 N-Channel MOSFET

This device is an N-channel MOSFET. See also “MOSFET” on page 4-12.

Multisim 8 Component Reference Guide 4-11

Transistors

4.7 MOSFET

A MOSFET is a Metal-Oxide-Semiconductor FET. This transistor is a type of FET that uses

an induced electrical field to control current through the device. Either negative or positive
gate voltages can be applied to control the current.
The substrate is usually connected to the most negatively biased part of the MOSFET, usually
the source lead. In the three-terminal MOSFETs, the substrate is internally connected to the
source. N-channel MOSFETs have an inward-pointing substrate arrow, and p-channel
MOSFETs have an outward-pointing arrow. N-channel and p-channel MOSFETs are
identical, except that their voltage polarities are opposite.
The 4-Terminal Enhanced N-MOSFET is an n-channel enhancement MOSFET. Because the
substrate lead is not connected to the source lead, it has four terminals.
The 4-Terminal Enhanced P-MOSFET is a p-channel enhancement MOSFET. Because the
substrate and source leads are not connected, it has four terminals.
Eight MOSFETs, both depletion-type and enhancement-type, are included in the parts bin.

4.7.1 Depletion MOSFETs

Like a JFET, a depletion MOSFET consists of a length of p-type (for a p-channel MOSFET)
or n-type (for an n-channel MOSFET) semiconductor material, called the channel, formed on
a substrate of the opposite type. The gate is insulated from the channel by a thin silicon
dioxide (SiO2) layer. Depletion MOSFETs are used in automatic-gain control (AGC) circuits.
3-terminal n-channel depletion MOSFET
3-terminal p-channel depletion MOSFET
4-terminal n-channel depletion MOSFET, substrate unconnected
4-terminal p-channel depletion MOSFET, substrate unconnected

4.7.2 Enhancement MOSFETs

An enhancement MOSFET has no physical channel between the drain and the source, unlike
the depletion MOSFET. Instead, the substrate extends all the way to the silicon dioxide (SiO2)

4-12 Electronics Workbench

 MOSFET

layer. An enhancement MOSFET works only with positive gate-source voltages.

Enhancement MOSFETs are extensively used in digital circuits and large-scale integration
(LSI) applications.
3-terminal n-channel enhancement MOSFET
3-terminal p-channel enhancement MOSFET
4-terminal n-channel enhancement MOSFET, substrate unconnected
4-terminal p-channel enhancement MOSFET, substrate unconnected
Multisim provides four MOSFET device models, which differ in the formulation of the
current-voltage characteristic. The parameter LEVEL in the model dialog specifies the model
to be used. LEVEL 1 is a modified Shichman-Hodges model. LEVEL 2 defines the geometry-
based analytical model. LEVEL 3 defines the semi-empirical short-channel model. LEVEL 4
defines the BS1M1 model. LEVEL 5 defines a new BS1M2 model.

4.7.3 DC Model
Due to the complexity of the MOSFET models used, only very basic formulas are provided in
the following description.
The DC characteristics are modeled by a nonlinear current source, ID.
Forward characteristics (VDS ≥ 0):

V TE = V TO + γ ϕ − V B S  − ϕ γ > 0,ϕ > 0


 fo r


0 for (VGS − VE ) ≤ 0
I D = β (VGS − VTE ) (1 + λVDS )
2
for 0 < (VGS − VTE ) ≤ VDS
β (VDS [2(VGS − VTE ) − VDS ](1 + λVDS ) for 0 < VDS ≤ (VGS − VTE )
Reverse characteristics (VDS < 0):


V TE = VTO = γ 

ϕ − V B D  − ϕ

Multisim 8 Component Reference Guide 4-13

Transistors

0 for (VGD − VTE ) ≤ 0

I D = − β (VGS − VTE ) 2 (1 − λVDS ) for 0 < (VGD − VTE ) ≤ −VDS
β (VDS [2(VGD − VTE ) + VDS ](1 − λVDS ) for 0 < VDS ≤ (VGD − VTE )
where

l = channel length modulation, measured in

1
volts

VTE = threshold voltage, in volts

VTO = zero-bias threshold voltage, in volts

γ = bulk-threshold parameter, in volts

j = surface potential at strong inversion, in volts

VBS = bulk-to-source voltage, in volts

VBD = bulk-drain voltage, in volts

VDS = drain-to-source voltage, in volts

4.7.4 Time-Domain Model

The time-domain model takes into account the charge-storage effects of the junction diodes
used to model MOSFETs. The diodes are modeled using the diode time-domain model
described in the Diodes Parts Bin chapter.

4.7.5 AC Small-Signal Model

In the linearized small-signal model, the junction diodes used to model the MOSFETs are
replaced by their equivalent small-signal models.

4-14 Electronics Workbench

 MOSFET

CGB, CGS, CGD are zero-bias junction capacitances.

dI D dI BS
gm = OP g BS = OP
dVGS dV BS
dI D dI BD
g DS = OP g BD = OP
dVGS dV BD
dI D
gmBS = OP
dV BS

4.7.6 MOSFET Level 1 Model Parameters and Defaults

Symbol Parameter Name Default Unit

VTO Threshold voltage 0 V

KP Transconductance coefficient 2e-05 A/V2

LAMBDA Channel-length modulation 0 1/V

PHI Surface potential 0.6 V

GAMMA Bulk-threshold parameter 0 V**0.5

RD Drain ohmic resistance 0 W

RS Source ohmic resistance 0 W

IS Bulk-junction saturation current 1e-14 A

CGBO Gate-bulk overlap capacitance per meter 0 F

channel length

CGDO Gate-drain overlap capacitance per meter 0 F

channel length

CGSO Gate-source overlap capacitance per meter 0 F

channel width

CBD Zero-bias bulk-drain junction capacitance 0 F

CBS Zero-bias bulk-source junction capacitance 0 F

Multisim 8 Component Reference Guide 4-15

Transistors

Symbol Parameter Name Default Unit

PB Bulk-junction potential 0.8 V

RSH Drain and source diffusion sheet resistance 0 W

CJ Zero-bias bulk junction bottom capacitance 0 F/m2

per m2 of junction area

MJ Bulk junction bottom grading coefficient 0.5 –

CJSW Zero-bias bulk junction sidewall capacitance 0 F/m

per m of junction perimeter.

MJSW Bulk junction sidewall grading coefficient 0.5 –

JS Bulk junction saturation current per m2 of 0 A/m2

junction area

TOX Oxide thickness 1e-07 m

NSUB Substrate doping 0 1/cm3

NSS Surface state density 0 1/cm2

TPG Type of gate material 1 –

LD Lateral diffusion 0 m

UO Surface mobility 600 cm2/Vs

KF Flicker noise coefficient 0 –

AF Flicker noise exponent 1 –

FC Coefficient for forward-bias depletion 0.5 –

capacitance formula

TNOM Parameter measurement temperature 27 °C

rD = rS = 10% to 15% of the on-state drain-source resistance, RDS(on).

4.8 MOSFET Thermal Model

4-16 Electronics Workbench

 MOSFET Thermal Model

This is an interactive device that lets you simulate the heat generated in a MOSFET. Pressing
“T” on your keyboard lets you toggle the displayed parameter between Junction, Dielectric
Bond and Case.

The following thermal electrical equivalent circuit represents the device’s model.

TJ

TB

TC

TA

Heat generated in a device’s junction flows from a higher temperature region through each
resistor-capacitor pair to a lower temperature region.
PDiss is a current source; its amplitude is the power consumed by the MOSFET. The voltages
of the nodes TJ, TB, TC and TA represent the temperature rise of the junction point of the
MOSFET, dielectric bond of the MOSFET, case of the MOSFET and ambient temperature.
The ambient temperature is considered constant (no temperature rise), so the voltage of TA is
zero and TA is grounded.

Multisim 8 Component Reference Guide 4-17

Transistors

4.9 JFETs (Junction FETs)

The JFET is a unipolar, voltage-controlled transistor that uses an induced electrical field to
control current. The current through the transistor is controlled by the gate voltage. The more
negative the voltage, the smaller the current.
A JFET consists of a length of an n-type or p-type doped semiconductor material called a
channel. The ends of the channel are called the source and the drain. The terminal with the
arrowhead represents the gate.
In an n-channel JFET, the gate consists of p-type material surrounding the n-channel. In a p-
channel JFET, the gate consists of n-type material surrounding the p-channel.

4.9.1 DC Model
The DC model characteristic is determined by a nonlinear current source, ID.
Forward characteristics (VDS ≥ 0):

0 for (VGS − VTO ) ≤ 0

I D = − β (VGS − VTO ) 2 (1 + λVDS ) for 0 < (VGS − VTO ) ≤ VDS
β (VDS [2(VGS − VTO ) − VDS ](1 + λVDS ) for 0 < VDS ≤ (VGS − VTO )

Reverse characteristics (VDS < 0):

0 for (VGS − VTO ) ≤ 0
I D = − β (VGS − VTO ) 2 (1 + λVDS ) for 0 < (VGS − VTO ) ≤ VDS
β (VDS [2(VGS − VTO ) − VDS ](1 + λVDS ) for 0 < VDS ≤ (VGS − VTO )
where

VGS = gate-source voltage, in volts

VDS = drain-source voltage, in volts

4-18 Electronics Workbench

 JFETs (Junction FETs)

VGD = gate-drain voltage, in volts

VGS(off) = gate-source cutoff voltage, in volts

IS = saturation current for the gate-drain and gate-source diode junctions

ID = drain-to-source current, in amperes

IDSS = drain-to-source saturation current, in amperes

β = IDSS = transconductance parameter in A/V2

[VGS ( off )] 2
l = channel-length modulation parameter measured in 1/V

Other symbols used in these equations are defined in “JFET Model Parameters and Defaults”.
Note β is not to be confused with gm, the AC small-signal gain mentioned later in this
chapter.
The charge storage occurring in the two gate junctions is modeled by the diode time-domain
model described in the Diodes Parts Bin chapter.
The diodes used to model the JFETs are represented by their small-signal models.
dID
gm = OP
dVGS
dID
gDS = OP
dVDS
dIGS
gGS = OP
dVGS
dIGD
gGD = OP
dVGD
where

gm = AC small-signal gain

gDS = small-signal forward admittance or transconductance

gGS and gGD are normally very small because the diode junctions are not forward-biased.
IGS and IGD are the diode current expressions mentioned in the diode modeling section.

Multisim 8 Component Reference Guide 4-19

Transistors

4.9.2 JFET Model Parameters and Defaults

Symbol Parameter Name Default Example Unit

VTO Threshold voltage -2 -2 V

BETA Transconductance 0.0001 1e-03 A/V

coefficient

LAMBDA Channel-length modulation 0 1e-04 1/V2

RD Drain ohmic resistance 0 100 W

RS Source ohmic resistance 0 100 W

IS Gate-junction saturation 1e-14 1e-14 A

current

Cgd Zero-bias gate-drain junction 0 1e-12 F

capacitance

Cgs Zero-bias gate-source 0 5e-12 F

junction capacitance

PB Gate-junction potential 1 .06 V

B Doping tail parameter 1 1.1 -

KF Flicker noise coefficient 0 - -

AF Flicker noise exponent 1 - -

FC Coefficient for forward-bias .5 - -

depletion capacitance
formula

TNOM Parameter measurement 27 50 °C

temperature

rD = rS = 10% to 15% of the on-state drain-to-source resistance, RDS(on).

4-20 Electronics Workbench

 Power MOSFET (N/P)

4.10 Power MOSFET (N/P)

The double-diffused or DMOS transistor is an example of a power MOSFET. This device is

fabricated on a lightly doped n-type substrate with a heavily doped region at the bottom for
drain contact. Two diffusions are used, one to create the p-type body region and another to
create the n-type source region.
The DMOS device is operated by applying a positive gate voltage, vGS, greater than the
threshold voltage Vt, which induces a lateral n channel in the p-type body region underneath
the gate oxide. Current is conducted through the resulting short channel to the substrate and
then vertically down the substrate to the drain.
The DMOS transistor can have a breakdown voltage as high as 600 V and a current capability
as high as 50 A is possible.
Power MOSFETs have threshold voltages in the range of 2 to 4 V. In comparison with BJTs,
power MOSFETs do not suffer second breakdown, nor do they require the large base-drive
currents of power BJTS. They also have a higher speed of operation than the power BJTs.
These advantages make power MOSFETs suited to switching applications, such as in motor-
control circuits.

4.11 Power MOSFET Complementary

These DMOS dual N- and P-channel enhancement mode power field effect transistors
minimize on-state resistance, provide superior switching performance, and withstand high
energy pulses in the avalanche and commutation modes. These devices are particularly suited
for low voltage applications such as notebook computer power management and other battery
powered circuits where fast switching, low in-line power loss, and resistance to transients are
needed.

4.12 N-Channel & P-Channel GaAsFET

Multisim 8 Component Reference Guide 4-21

Transistors

This component is a high-speed field-effect transistor that uses gallium arsenide (GaAs) as the
semiconductor material rather than silicon. It is generally used as a very high frequency
amplifier (into the gigahertz range). A GaAsFET consists of a length of n-type or p-type
doped GaAs called the channel. The ends of the channel are called the source and the drain.
The terminal with the arrowhead represents the gate. GaAsFETs are used in microwave
applications.

4.12.1 Model and Characteristic Equations

The GaAsFET component is based on the Statz model.

0 for Vgs − VTO < 0


   α 
3

Id =  1 − 1 − Vds ∗  
 3 
β ∗ (1+ λ∗ V )∗ V − V 2 ∗ 
( ) for Vgs − VTO ≥ 0


ds gs TO
1 + β∗ Vgs − VTO ( )
where

Vgs = gate-source voltage

Vds = drain-source voltage

VTO = threshold voltage; equivalent to the gate-

source cutoff voltage

a = saturation voltage

b = transconductance

l = channel-length modulation

Id = drain to source current

4-22 Electronics Workbench

 IGBT

4.12.2 GaAsFET Parameters and Defaults

Symbol Parameter name Default Unit

VTO Pinch-off voltage -2 V

BETA Transconductance 0.0001 A/V2

B Doping tail extending parameter 0.3 1/V

ALPHA Saturation voltage 2 1/V

LAMBDA Channel-length modulation 0 1/V

RD Drain ohmic resistance 0 W

RS Source ohmic resistance 0 W

CGS Zero-bias G-S junction capacitance 0 F

CGD Zero-bias G-D junction capacitance 0 F

PB Gate junction potential 1 V

KF Flicker noise coefficient 0 -

AF Flicker noise exponent 1 -

FC Coefficient for forward-bias depletion 0.5

capacitance formula

4.13 IGBT

The IGBT is an MOS gate-controlled power switch with a very low on-resistance. It is similar
in structure to the MOS-gated thyristor, but maintains gate control of the anode current over a
wide range of operating conditions.
The low on-resistance feature of the IGBT is due to conductivity modulation of the n epitaxial
layer grown on a p+ substrate. The on-resistance values have been reduced by a factor of

Multisim 8 Component Reference Guide 4-23

Transistors

about 10 compared with those of conventional n-channel power MOSFETs of similar size and
voltage capability.
Changes to the epitaxial structure and the addition of recombination centers are responsible
for the reduction in the fall time and an increase in the latching current level of the IGBT. Fall
times as low as 0.1µs and latching currents as high as 50A can be achieved, while retaining
on-resistance values <0.2Ω for a 0.09cm2 chip area.

4.14 Unijunction Transistors

The Programmable Unijunction Transistor is designed for adjustable characteristics such as

valley current, peak current and intrinsic standoff ratio.

4-24 Electronics Workbench

Chapter 5
Analog Components

5.1 Opamp

5.1.1 Opamp Model Parameters

An ideal operational amplifier (Opamp) is an amplifier with infinite gain, infinite input
impedance and zero output impedance. With the application of negative feedback, Opamps
can be used to implement functions such as addition, subtraction, differentiation, integration,
averaging and amplification.
An opamp can have a single input and single output, a differential input and single output, or
a differential input and differential output.

5.1.2 Ideal Opamp Model

The ideal opamp model is the fastest to simulate. Its characteristics include:
• open-loop voltage gain (A)
The open-loop gain is the gain of the opamp without any feedback applied which in the
ideal opamp is infinite. This is not possible in the typical opamp, but it will be in the order
of 120 dB.

Multisim 8 Component Reference Guide 5-1

Analog Components

• frequency response
The frequency response of an opamp is finite and its gain decreases with frequency. For
stability, a dominant pole is intentionally added to the opamp to control this decreasing
gain with frequency. In an internally compensated opamp, the response typically is set for
-6dB/octive roll off with a -3dB frequency in range of 10 Hz. With an externally
compensated Opamps, the -3 dB corner frequency can be changed by adding an external
capacitor.
• unity-gain bandwidth
This is the frequency at which the gain of the opamp is equal to 1. This is the highest
frequency at which the opamp can be used, typically as a unity gain buffer.
• common mode rejection ratio (CCMR)
This is the ability of an opamp to reject or to not amplify a signal that is applied to both its
input pins expressed as a ratio (in dBs) of its common mode gain to its open loop gain.
• slew rate
This is the rate of change of output voltage expressed in volts per microsecond.

5.1.3 Opamp: Background Information

The operational amplifier is a high-gain block based upon the principle of a differential
amplifier. It is common to applications dealing with very small input signals.
The open-loop voltage gain (A) is typically very large (10e+5 to 10e+6). If a differential input
is applied across the “+” and “-” terminals, the output voltage will be:
V = A * (V+ - V-)
The differential input must be kept small, since the opamp saturates for larger signals. The
output voltage will not exceed the value of the positive and negative power supplies (Vp), also
called the rails, which vary typically from 5 V to 15 V. This property is used in a Schmitt
trigger, which sets off an alarm when a signal exceeds a certain value.
Other properties of the opamp include a high input resistance (Ri) and a very small output
resistance (Ro). Large input resistance is important so that the opamp does not place a load on
the input signal source. Due to this characteristic, opamps are often used as front-end buffers
to isolate circuitry from critical signal sources.
Opamps are also used in feedback circuits, comparators, integrators, differentiators, summers,
oscillators and wave-shapers. With the correct combination of resistors, both inverting and
non-inverting amplifiers of any desired voltage gain can be constructed.

5-2 Electronics Workbench

 Opamp

5.1.4 Opamp: Simulation Models

Opamps are provided with several levels of simulation models of increasing complexity and
accuracy. The following model levels are used to distinguish between the various models:
• L1 - this is the simplest model with the opamp modeled as a gain block with a differential
input and a single ended output.
• L2 - this is a more complex model in which the supply voltages are included in the
simulation.
• L3 - this is a model of increasing complexity where additional control pins are supported.
• L4 - this is the most complex and accurate model with a majority of the external control
pins modeled.

5.1.4.1 L1 Simulation Model

This is the simplest simulation model and is equivalent to the Three Terminal Opamp model
of EWB Version 5. This model is an idealized differential input, single output model that
models only the first order characteristics of the opamp.
The modeled opamp parameters are:
• open loop gain
• input resistance
• output resistance
• slew rate
• unity-gain bandwidth
• input bias current
• input offset current
The opamp is modeled by distributing the open-loop voltage gain, A, across three stages. The
first and second stages model the first and second poles of the opamp, and the third stage
models the output impedance.
The same model is used for DC, time-domain and AC analyses.

IOS
IB1 = IBIAS +
2
IOS
IB 2 = IBIAS –
2
A1∗VIN 1
I1 =
R1
A1 = A 1/ 3

Multisim 8 Component Reference Guide 5-3

Analog Components

where

A1 = open-loop voltage gain of the first stage

RIN = input resistance, in ohm

IBIAS = input bias current, in amperes

IOS = input offset current, in amperes

R1 = 1 kΩ
fu
fP 1 =
A
1
C1 =
2π ∗ R1∗ fP1
The slew rate limits the rate of change of I1 to model the rate of change of output voltage.
A2 ∗VIN 2
I1 =
R2
A2 = A1/3
R2 = ROUT
where

ROUT = output resistance

A third stage is introduced by specifying the location of the second pole:

1
C2 =
2π ∗ R2 ∗ f P 2
R2 = 1 kΩ
R3 = ROUT
A1/ 3 ∗VIN
I3 =
R3

5-4 Electronics Workbench

 Opamp

where

fu = unity-gain bandwidth in hertz; i.e., the

frequency at which the open-loop voltage
gain equals 1.

fP2 = second-pole frequency. A third stage may

be introduced by specifying the location of
a second pole in hertz.

CC = compensation capacitance, which shifts

the dominant pole to the left in the
frequency response. Its value is typically
30-40 picofarads.

SR = slew rate, which is the rate of change of

output voltage (in V/s) in response to a
step input.

5.1.4.2 L2 Simulation Model

This is a more complex simulation model and is equivalent to the Five Terminal Opamp
model of EWB Version 5 The base L2 model is a differential input, single output model based
on the Boyle-Cohn-Pederson macro model, which includes the supply voltage connections.
This model supports second order effects such as common-mode rejection, output voltage and
current limiting characteristics of the opamp in addition to the first order effects.
The modeled opamp parameters are:
• open loop gain
• input resistance
• output resistance
• slew rate
• unity-gain bandwidth
• common mode rejection (CCMR)
• input bias current
• input offset current
• input bias current
• input offset voltage
• input bias voltage
• output voltage swing
• output current limiting

Multisim 8 Component Reference Guide 5-5

Analog Components

The internal components of a 741 opamp are shown below.

The circuit is divided into three stages. The input stage consists of ideal transistors, Q1 and
Q2, and associated sources and passive elements. It produces the linear and nonlinear
differential mode (DM) and common mode (CM) input characteristics. The capacitor, Ce,
introduces a second order-effect for the slew rate and C1 introduces a second-order effect to
the phase response.
SR∗ CC
IC 1 =
2
2∗ IC 1
Ce = RC1 =
SR 2π ∗ fu∗ CC
IOS
IB1 = Ibs +
2
IC1
β1 =
IB 1
IC1
β2 =
IB 2
 ( β 1 + 1) ( β 2 + 1) 
IEE  +  IC1
 β1 β2 
200
RE =
IEE

Assume IS1 = 1e–16

 V OS 
I S 2 = I S 1 1 + 0.025 
 
CC
C1 = t a n ∆ϕ
2
The interstage provides the DM and CM gains and consists of voltage-controlled current
sources gcm, ga and gb and resistors, R02 and R2. The dominant time constant of the opamp is
provided by the internal feed-back capacitor, cc. In some opamps, the two nodes of cc are made
available to the outside world for external compensation. The output stage models DC and AC
output resistance. The elements d3, vc, d4 and ve provide maximum desired voltage swings.
Elements d1, d2, rcc and gc provide the current-limiting function.

5-6 Electronics Workbench

 Opamp

Interstage:

IC
gm =
0.02585
β1 + β2  1
Re1 =  RC1 − 
β1 + β 2 + 2  gm 
1
ga =
RC1
ARC
gb =
100e 3 R 02
Ga
Gcm =
CMRR

Output stage:

Rout
R01 =
2
R02 = Rout − R01
I x = 2 * I c gb − I SC
 
I SD = I x exp − R01*I SC 
 0.025 

0.025 I x
RCC = ln
100i x I SD
1
GC =
RC
I
VC = VCC − VSW + VΤ ∗ I n I SC
+

SD
I
VE = Vee − VSW + VΤ ∗ I n I SC
−

SD

Note In addition to the base L2 simulation model, other models of this complexity or level
are supplied by the various manufacturers for their particular opamps.

Multisim 8 Component Reference Guide 5-7

Analog Components

5.1.4.3 L3 Simulation Model

This is a more complex simulation model that is equivalent to the Seven Terminal Opamp
models of EWB Version 5. This model is supplied by the various manufacturers for the more
complex Opamps that have additional pins to support functions such as external
compensation and output offset balance controls.
Each model is unique as it was developed by the individual companies to support their
products. Therefore, a general description of each model is not possible.

5.1.4.4 L4 Simulation Model

This is generally the most complex opamp simulation model and is equivalent to the Nine
Terminal Opamp model of EWB Version 5. Models are supplied by the various manufacturers
for the more complex Opamps that have additional pins to support functions such as external
compensation and output offset balance controls.
Each model is unique as it was developed by the individual companies to support their
products. Therefore, a general description of each model is not possible.

5.2 Norton Opamp

5.2.1 The Component

The Norton amplifier, or the current-differencing amplifier (CDA) is a current-based device.
Its behavior is similar to an opamp, but it acts as a transresistance amplifier where the output
voltage is proportional to the input current.

5.2.2 Norton Opamp: Simulation models

The same levels of simulation model as the opamps are provided with several levels of
simulation models of increasing complexity and accuracy.
The following model levels are used to distinguish between these models:

5-8 Electronics Workbench

 Comparator

• L1 - this is the simplest model with the opamp modeled as a gain block with a differential
input and a single ended output.
• L2 - this is a more complex model in which the supply voltages are included in the
simulation.
• L3 - this is a model of increasing complexity where additional control pins are supported.
• L4 - this is the most complex and accurate model with a majority of the external control
pins modeled.

5.3 Comparator

5.3.1 The Component

This component models the high-level behavior of a comparator. A comparator is an IC
operational-amplifier whose halves are well balanced and without hysteresis and is therefore
suitable for circuits in which two electrical quantities are compared. The comparator
component models conversion speed, quantization error, offset error and output current
limitation.
A comparator is a circuit that compares two input voltages and produces an output in either of
two states, indicating the greater than or less than relationship of the inputs.
A comparator switches to one state when the input reaches the upper trigger point. It switches
back to the other state when the input falls below the lower trigger point.
A voltage comparator may be implemented with any op-amp, with consideration for operating
frequencies and slew rate, or with specialized ICs such as the LM339.
The comparator compares a reference voltage, fixed or variable, with an input waveform.
If the input is applied to the non-inverting input and the reference to the inverting input (lower
circuit), the comparator will be operating in the non-inverting mode. In this case, when the
input voltage is equal to (or slightly less than) the reference voltage the output will be at its
lowest limit (near the negative supply) and when the input is equal to (or slightly greater than)
the reference voltage the output will change to its highest value (near the positive supply).

Multisim 8 Component Reference Guide 5-9

Analog Components

If the inverting and non-inverting terminals are reversed (upper circuit) the comparator will
operate in the inverting mode.

5.3.2 Comparator: Simulation models

The same levels of simulation model as the opamps are provided with several levels of
simulation models of increasing complexity and accuracy.
The following model levels are used to distinguish between these models:
• L1 - this is the simplest model with the opamp modeled as a gain block with a differential
input and a single ended output.
• L2 - this is a more complex model in which the supply voltages are included in the
simulation.
• L3 - this is a model of increasing complexity where additional control pins are supported.
• L4 - this is the most complex and accurate model with a majority of the external control
pins modeled.

5-10 Electronics Workbench

 Wide Band Amplifier

5.3.3 Comparator Parameters and Defaults

Symbol Parameter name Default Unit

Voffset Input voltage offset 0.7 V

A Gain 200000 V/V

Voh Output high level 3.5 V

Vol Output low level 0.23 V

Trr Low-to-high response time 1e-07 s

Trf High-to-low response time 1.5e-07 s

Tr Rise time 1e-07 s

Tf Fall time 6e-08 s

Icc+ Positive supply current 0.0051 A

Icc- Negative supply current 0.0041 A

Imax+ Maximum positive supply current 0.006 A

Imax- Maximum negative supply current 0.005 A

5.4 Wide Band Amplifier

Multisim 8 Component Reference Guide 5-11

Analog Components

5.4.1 The Component

The typical opamp, such as a general purpose 741 type opamp, has been internally
compensated for a unity gain bandwidth of about 1 MHz. Wide band amplifiers are opamps
that have been designed with a unity gain bandwidth of greater than 10 MHz and typically in
the 100 MHz range. These devices are used for application such as video amplifiers.

5.4.2 Wide Band Amplifier: Simulation models

The same levels of simulation model as the opamps are provided with several levels of
simulation models of increasing complexity and accuracy.
The following model levels are used to distinguish between these models:
• L1 - this is the simplest model with the opamp modeled as a gain block with a differential
input and a single ended output.
• L2 - this is a more complex model in which the supply voltages are included in the
simulation.
• L3 - this is a model of increasing complexity where additional control pins are supported.
• L4 - this is the most complex and accurate model with a majority of the external control
pins modeled.

5.5 Special Function

5.5.1 The Component

These are a group of analog devices that are used for the following applications:
• instrumentation amplifier
• video amplifier
• multiplier/divider
• preamplifier
• active filter
• high precision reference

5-12 Electronics Workbench

 Special Function

5.5.2 Special Function: Simulation models

The same levels of simulation model as the opamps are provided with several levels of
simulation models of increasing complexity and accuracy.
The following model levels are used to distinguish between these models:
• L1 - this is the simplest model with the opamp modeled as a gain block with a differential
input and a single ended output.
• L2 - this is a more complex model in which the supply voltages are included in the
simulation.
• L3 - this is a model of increasing complexity where additional control pins are supported.
• L4 - this is the most complex and accurate model with a majority of the external control
pins modeled.

Multisim 8 Component Reference Guide 5-13

Analog Components

5-14 Electronics Workbench

Chapter 6
TTL

6.1 Standard TTL

The characteristics of the standard TTL series can be illustrated by the 7400 quad NAND gate
IC.
The 74 series uses a nominal supply voltage (VOC) of 5V and can operate reliably over the
range 4.75 to 5.25 V. The voltages applied to any input of a standard 74 series IC must never
exceed +5.5 V. The maximum negative voltage that can be applied to a TTL input is -0.5 V.
The 74 series IC is designed to operate in ambient temperatures ranging from 0 to 70° C. The
guaranteed worst-case DC noise margins for the 74 series are 400 mV.
A standard TTL NAND gate requires an average power of 10 mV.
A standard TTL output can typically drive 10 standard TTL inputs.

6.2 Schottky TTL

The basic circuitry of the standard TTL series forms the central part of several other TTL
series, including the Schottky TTL, 74S series.
The Schottky TTL (the 74S series) reduces the storage-time delay by not allowing the
transistor to go as deeply into saturation. The 74S series does this by using a Schottky barrier
diode connected between the base and the collector of each transistor.

Multisim 8 Component Reference Guide 6-1

TTL

Circuits in the 74S series also use smaller resistor values to help improve switching times.
This increases the circuit average power dissipation to about 20 mW. These circuits also use a
Darlington pair to provide a shorter output rise time when switching from ON to OFF.

6.3 Low-Power Schottky TTL

The low-power Schottky TTL (the 74LS series) is lower in power and slower in speed than
the 74S series. It uses the Schottky-clamped transistor, but with larger resistor values than the
74S series. The larger resistor values reduce the power requirements of the circuit, but
increase the switching times.
A NAND gate in the 74LS series typically has an average propagation delay of 9.5 ns and an
average power dissipation of 2 mW.

6.4 74xx

6.4.1 74xx00 (Quad 2-In NAND)

This device contains four independent 2-input NAND gates.
Logic function:

NAND gate truth table:

A B Y
0 0 1
1 0 1
0 1 1
1 1 0

6-2 Electronics Workbench

 74xx

6.4.2 74xx01 (Quad 2-In NAND)

This device contains four independent 2-input NAND gates.
Logic function:

NAND gate truth table:

A B Y
0 0 1
1 0 1
0 1 1
1 1 0

6.4.3 74xx02 (Quad 2-In NOR)

This device contains four independent 2-input NOR gates.
Logic function:

NOR gate truth table:

A B Y
0 0 1
1 0 0
0 1 0
1 1 0

6.4.4 74xx03 (Quad 2-In NAND (Ls-OC))

This device contains four independent 2-input NAND gates. For correct performance, the
open collector outputs require pull-up resistors.
Logic function:

Multisim 8 Component Reference Guide 6-3

TTL

NAND gate truth table:

A B Y
0 0 1
0 1 1
1 0 1
1 1 0

6.4.5 74xx04 (Hex INVERTER)

This device contains six independent INVERTER gates.
Logic function:

INVERTER gate truth table:

A Y
1 0
0 1

6.4.6 74xx05 (Hex INVERTER (OC))

This device contains six independent INVERTER gates. For correct performance, the open
collector outputs require pull-up resistors.
Logic function:

INVERTER gate truth table:

A Y
1 0
0 1

6-4 Electronics Workbench

 74xx

6.4.7 74xx06 (Hex INVERTER (OC))

This device contains six independent INVERTER gates. For correct performance, the open
collector outputs require pull-up resistors.
Logic function:

INVERTER gate truth table:

A Y
1 0
0 1

6.4.8 74xx07 (Hex BUFFER (OC))

This device contains six independent BUFFER/non-inverting gates. For correct performance,
the open collector outputs require pull-up resistors.
Logic function:

BUFFER gate truth table:

A Y
0 0
1 1

6.4.9 74xx08 (Quad 2-In AND)

This device contains four independent 2-input AND gates.
Logic function:

Multisim 8 Component Reference Guide 6-5

TTL

AND gate truth table:

A B Y
0 0 0
1 0 0
0 1 0
1 1 1

6.4.10 74xx09 (Quad 2-In AND (OC))

This device contains four independent 2-input AND gates. For correct performance, the open
collector outputs require pull-up resistors.
Logic function:

AND gate truth table:

A B Y
0 0 0
1 0 0
0 1 0
1 1 1

6.4.11 74xx10 (Tri 3-In NAND)

This device contains three independent 3-input NAND gates.
Logic function:

6-6 Electronics Workbench

 74xx

NAND gate truth table

A B C Y
0 0 0 1
1 0 0 1
0 1 0 1
1 1 0 1
0 0 1 1
1 0 1 1
0 1 1 1
1 1 1 0

6.4.12 74xx100 (8-Bit Bist Latch)

The 74100 is an 8-bit bistable latch.
8-bit bistable latch truth table:

6.4.13 74xx107 (Dual JK FF(clr))

This device is a positive pulse-triggered flip-flop. It contains two independent J-K flip-flops
with individual J-K, clock, and direct clear inputs.
JK flip-flop truth table:

CLR CLK J K Q Q
0 X X X 0 1
1 · 0 0 Hold
1 · 1 0 1 0
1 · 0 1 0 1
1 · 1 1 Toggle

Multisim 8 Component Reference Guide 6-7

TTL

6.4.14 74xx109 (Dual JK FF (+edge, pre, clr))

This device contains two independent J-K positive edge-triggered flip-flops.
JK flip-flop truth table:

PRE CLR CLK J K Q Q

0 1 X X X 1 0
1 0 X X X 0 1
0 0 X X X 1 1
1 1 · 0 0 0 1
1 1 · 1 0 Toggle
1 1 · 0 1 Hold
1 1 · 1 1 1 0
1 1 0 X X Hold

· = positive edge-triggered

6.4.15 74xx11 (Tri 3-In AND)

This device contains three independent 3-input AND gates.
Logic function:
Y = ABC

AND gate truth table:

A B C Y
0 0 0 0
1 0 0 0
0 1 0 0
1 1 0 0
0 0 1 0
1 0 1 0
0 1 1 0
1 1 1 1

6-8 Electronics Workbench

 74xx

6.4.16 74xx112 (Dual JK FF(-edge, pre, clr))

This device contains two independent J-K negative edge-triggered flip-flops.
JK flip-flop truth table:

PRE CLR CLK J K Q Q

0 1 X X X 1 0
1 0 X X X 0 1
0 0 X X X 1 1
1 1 Ø 0 0 Hold
1 1 Ø 1 0 1 0
1 1 Øëë 0 1 0 1
ëëëë
ëëëë
1 1 Ø 1 1 Toggle
1 1 0 X X Hold

Ø = negative edge-triggered

Multisim 8 Component Reference Guide 6-9

TTL

6.4.17 74xx113 (Dual JK MS-SLV FF (-edge, pre))

This device contains two independent J-K negative edge-triggered flip-flops.
JK flip-flop truth table:

PRE CLK J K Q Q
0 X X X 1 0
1 0 0 Hold
1 ëëëë 1 0 1 0
ëëëë
ëëëë
ëëëë
ëëëë
ëëëë
ëëëë
ëëëë
ëëëë
ëëëë
1 0 1 0 1
1 1 1 Toggle
1 1 X X Hold

Ø = negative edge-triggered

6.4.18 74xx114 (Dual JK FF (-edge, pre, com clk & clr))

This device contains two independent J-K negative edge-triggered flip-flops.
JK flip-flop truth table:

PRE CLR CLK J K Q Q

0 0 X X X 1 0
1 0 X X X 0 1
0 0 X X X 1 1
1 1 Ø 0 0 Hold
1 1 Ø 1 0 1 0
1 1 Ø 0 1 0 1
1 1 Ø 1 1 Toggle
1 1 1 X X Hold

Ø = negative edge-triggered

6-10 Electronics Workbench

 74xx

6.4.19 74xx116 (Dual 4-bit latches (clr))

This device contains two independent 4-bit latches. Each 4-bit latch has an independent
asynchronous clear input and a gated two-input enable circuit.
4-bit latch truth table:

INPUTS
OUTPUT
ENABLE

CLR C1 C2 DATA Q
1 0 0 0 0
1 0 0 1 1
1 X 1 X Hold
1 1 X X Hold
0 X X X 0

6.4.20 74xx12 (Tri 3-In NAND (OC))

This device contains three independent 3-input NAND gates. For correct performance, the
open collector outputs require pull-up resistors.
Logic function:
Y = ABC

NAND gate truth table:

A B C Y
0 0 0 1
1 0 0 1
0 1 0 1
1 1 0 1
0 0 1 1
1 0 1 1
0 1 1 1
1 1 1 0

Multisim 8 Component Reference Guide 6-11

TTL

6.4.21 74xx125 (Quad bus BUFFER w/3-state Out)

This device contains four independent BUFFER/non-inverting gates with 3-state outputs.
BUFFER gate truth table:
A G Y
1 0 0
0 0 1
X 1 Z

Z = high impedance

The output of the bus buffer is disabled when G is high.

6.4.22 74xx126 (Quad bus BUFFER w/3-state Out)

This device contains four independent BUFFER/non-inverting gates with 3-state outputs.
BUFFER gate truth table

A G Y
1 1 1
0 1 0
X 0 Z

Z = high impedance

The output of the bus buffer is disabled when G is low.

6.4.23 74xx13 (Dual 4-In NAND (Schmitt))

This device is a dual 4-input Schmitt-triggered NAND gate.

6-12 Electronics Workbench

 74xx

6.4.24 74xx132 (Quad 2-In NAND (Schmitt))

NAND gate truth table:

A B Y
1 1 0
0 X 1
X 0 1

VT+ = 1.8V (at 5 Volt test condition)

VT- = 0.95V (at 5 Volt test condition)

6.4.25 74xx133 (13-In NAND)

Logic function:
Y = ABCDEFGHIJKLM

NAND gate truth table

INPUTS A THRU M Y
All inputs 1 0
One or more inputs 0 1

6.4.26 74xx134 (12-In NAND w/3-state Out)

12-Input NAND with 3-state outputs:

INPUTS A THRU L OC Y
All inputs 1 0 0
One or more inputs 0 0 1
Don't care 1 Z

Z = high impedance (off)

Multisim 8 Component Reference Guide 6-13

TTL

6.4.27 74xx135 (Quad Ex-OR/NOR Gate)

This device can operate as Exclusive-OR gate (C input low) or as Exclusive-NOR gate (C
input high).
Exclusive-OR/NOR gate truth table:

INPUTS OUTPUT

A B C Y
0 0 0 0
0 1 0 1
1 0 0 1
1 1 0 0
0 0 1 1
0 1 1 0
1 0 1 0
1 1 1 1

6.4.28 74xx136 (Quad 2-in Exc-OR gate)

This device is a quadruple 2-input exclusive-OR gate with open-collector outputs.
Exclusive-OR gate truth table:

INPUTS OUTPUT

A B Y
0 0 0
0 1 1
1 0 1
1 1 0

6.4.29 74xx138 (3-to-8 Dec)

This device decodes one of eight lines dependent on the conditions at the three binary select
inputs and the three enable inputs.

6-14 Electronics Workbench

 74xx

3-to-8 decoder/demultiplexer truth table:

SELECT

GL G1 G2 C B A Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7
X X 1 X X X 1 1 1 1 1 1 1 1
X 0 X X X X 1 1 1 1 1 1 1 1
0 1 0 0 0 0 0 1 1 1 1 1 1 1
0 1 0 0 0 1 1 0 1 1 1 1 1 1
0 1 0 0 1 0 1 1 0 1 1 1 1 1
0 1 0 0 1 1 1 1 1 0 1 1 1 1
0 1 0 1 0 0 1 1 1 1 0 1 1 1
0 1 0 1 0 1 1 1 1 1 1 0 1 1
0 1 0 1 1 0 1 1 1 1 1 1 0 1
0 1 0 1 1 1 1 1 1 1 1 1 1 0
1 1 0 X X X Output corresponding to stored address 0; all
others 1

6.4.30 74xx139 (Dual 2-to-4 Dec/DEMUX)

This decoder/demultiplexer contains two individual two-line to four-line decoders. It features
fully buffered inputs, each of which represents only one normalized load to its driving circuit.
2-to-4 decoder/demultiplexer truth table:

INPUTS OUTPUTS

ENABLE SELECT

G B A Y0 Y1 Y2 Y3
1 X X 1 1 1 1
0 0 0 0 1 1 1
0 0 1 1 0 1 1
0 1 0 1 1 0 1
0 1 1 1 1 1 0

6.4.31 74xx14 (Hex INVERTER (Schmitt))

A key feature of this integrated circuit is its high noise immunity. Due the to the Schmitt-
trigger action, this device is ideal for circuits that are susceptible to unwanted small signals,
such as noise.

Multisim 8 Component Reference Guide 6-15

TTL

INVERTER gate truth table:

A Y
0 1
1 0

The voltage threshold levels are as follows:

VT- = 0.95V (at 5 Volt test condition)

VT+ = 1.8V (at 5 Volt test condition)

6.4.32 74xx145 (BCD-to-Decimal Dec)

The BCD-to-decimal decoder/driver consists of eight inverters and ten four-input NAND
gates. These decoders feature high-performance, n-p-n output transistors designed for use as
indicator/relay drivers or as open-collector logic-circuit drivers.
BCD to decimal decoder/driver truth table:

INPUTS OUTPUTS

No. D C B A 0 1 2 3 4 5 6 7 8 9
O 0 0 0 0 0 1 1 1 1 1 1 1 1 1
1 0 0 0 1 1 0 1 1 1 1 1 1 1 1
2 0 0 1 0 1 1 0 1 1 1 1 1 1 1
3 0 0 1 1 1 1 1 0 1 1 1 1 1 1
4 0 1 0 0 1 1 1 1 0 1 1 1 1 1
5 0 1 0 1 1 1 1 1 1 0 1 1 1 1
6 0 1 1 0 1 1 1 1 1 1 0 1 1 1
7 0 1 1 1 1 1 1 1 1 1 1 0 1 1
8 1 0 0 0 1 1 1 1 1 1 1 1 0 1
9 1 0 0 1 1 1 1 1 1 1 1 1 1 0
1 0 1 0 1 1 1 1 1 1 1 1 1 1
1 0 1 1 1 1 1 1 1 1 1 1 1 1
1 1 0 0 1 1 1 1 1 1 1 1 1 1
INVALID

1 1 0 1 1 1 1 1 1 1 1 1 1 1
1 1 1 0 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1

6-16 Electronics Workbench

 74xx

6.4.33 74xx147 (10-to-4 Priority Enc)

This TTL encoder features priority decoding of the inputs to ensure that only the highest-
order data line is encoded. It encodes nine data lines to four-line (8-4-2-1) BCD.
10l-line to 4-line priority encoder truth table:

INPUTS OUTPUTS

1 2 3 4 5 6 7 8 9 D C B A
1 1 1 1 1 1 1 1 1 1 1 1 1
X X X X X X X X 0 0 1 1 0
X X X X X X X 0 1 0 1 1 1
X X X X X X 0 1 1 1 0 0 0
X X X X X 0 1 1 1 1 0 0 1
X X X X 0 1 1 1 1 1 0 1 0
X X X 0 1 1 1 1 1 1 0 1 1
X X 0 1 1 1 1 1 1 1 1 0 0
X 0 1 1 1 1 1 1 1 1 1 0 1
0 1 1 1 1 1 1 1 1 1 1 1 0

6.4.34 74xx148 (8-to-3 Priority Enc)

This TTL encoder features priority decoding of the inputs to ensure that only the highest-
order data line is encoded. It encodes eight data lines to three-line (4-2-1) binary (octal).
8-line to 3-line priority encoder truth table:

INPUTS OUTPUTS

EI 0 1 2 3 4 5 6 7 A2 A1 A0 GS EO
1 X X X X X X X X 1 1 1 1 1
0 1 1 1 1 1 1 1 1 1 1 1 1 0
0 X X X X X X X 0 0 0 0 0 1
0 X X X X X X 0 1 0 0 1 0 1
0 X X X X X 0 1 1 0 1 0 0 1
0 X X X X 0 1 1 1 0 1 1 0 1
0 X X X 0 1 1 1 1 1 0 0 0 1
0 X X 0 1 1 1 1 1 1 0 1 0 1
0 X 0 1 1 1 1 1 1 1 1 0 0 1
0 0 1 1 1 1 1 1 1 1 1 1 0 1

Multisim 8 Component Reference Guide 6-17

TTL

6.4.35 74xx15 (3 3-Input AND)

Logic function:
Y = ABC

AND gate truth table:

A B C Y
1 1 1 1
0 X X 0
X 0 X 0
X X 0 0

6.4.36 74xx150 (1-of-16 Data Sel/MUX)

This device can select one of sixteen data sources when a 4-bit binary number is applied to the
inputs. It is equipped with one enable input and a complementary output.
Truth table:

INPUTS OUTPUTS

D C B A G W
X X X X 1 1
0 0 0 0 0 EO
0 0 0 1 0 E1
0 0 1 0 0 E2
0 0 1 1 0 E3
0 1 0 0 0 E4
0 1 0 1 0 E5
0 1 1 0 0 E6
0 1 1 1 0 E7
1 0 0 0 0 E8
1 0 0 1 0 E9
1 0 1 0 0 E10
1 0 1 1 0 E11
1 1 0 0 0 E12
1 1 0 1 0 E13
1 1 1 0 0 E14
1 1 1 1 1 E15

6-18 Electronics Workbench

 74xx

6.4.37 74xx151 (1-of-8 Data Sel/MUX)

This data selector/multiplexer contains full on-chip binary decoding to select the desired data
source. It selects one of eight data sources and is equipped with one enable input and two
complementary outputs.
Data selector/multiplexer truth table:
SELECT STROBE OUTPUTS

C B A G Y W
X X X 1 0 1
0 0 0 0 D0 D0
0 0 1 0 D1 D1
0 1 0 0 D2 D2
0 1 1 0 D3 D3
1 0 0 0 D4 D4
1 0 1 0 D5 D5
1 1 0 0 D6 D6
1 1 1 0 D7 D7

6.4.38 74xx152 (Data Sel/MUX)

This data selector/multiplexer contains full on-chip binary decoding to select one-of-eight
data sources.
Data selector/multiplexer truth table:

SELECT INPUTS OUTPUT

C B A W
0 0 0 D0
0 0 1 D1
0 1 0 D2
0 1 1 D3
1 0 0 D4
1 0 1 D5
1 1 0 D6
1 1 1 D7

Multisim 8 Component Reference Guide 6-19

TTL

6.4.39 74xx153 (Dual 4-to-1 Data Sel/MUX)

This data selector/multiplexor contains inverters and drivers to supply fully complementary,
on-chip, binary decoding data selection to the AND-OR gates. Separate strobe inputs are
provided for each of the two four-line sections.
Data selector/multiplexer truth table:

SELECT DATA INPUTS STROBE OUTPUTS

B A C0 C1 C2 C3 G Y
X X X X X X 1 0
0 0 0 X X X 0 0
0 0 1 X X X 0 1
0 1 X 0 X X 0 0
0 1 X 1 X X 0 1
1 0 X X 0 X 0 0
1 0 X X 1 X 0 1
1 1 X X X 0 0 0
1 1 X X X 1 0 1

6.4.40 74xx154 (4-to-16 Dec/DEMUX)

This 4-line-to-16-line decoder uses TTL circuitry to decode four binary-coded inputs into one
of sixteen mutually exclusive outputs when both the strobe inputs are low.

6-20 Electronics Workbench

 74xx

4-to-16 decoder/demultiplexer truth table:

INPUTS OUTPUTS

G1 G2 D C B A 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
0 0 0 0 0 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1
0 0 0 0 1 0 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1
0 0 0 0 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1
0 0 0 1 0 0 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1
0 0 0 1 0 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1
0 0 0 1 1 0 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1
0 0 0 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1
0 0 1 0 0 0 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1
0 0 1 0 0 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1
0 0 1 0 1 0 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1
0 0 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1
0 0 1 1 0 0 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1
0 0 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1
0 0 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 1
0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0
0 1 X X X X 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 0 X X X X 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 X X X X 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

6.4.41 74xx155 (Dual 2-to-4 Dec/DEMUX)

This device features a dual 1-line-to-4-line demultiplexer with individual strobes and
common binary-address inputs.
Decoder/demultiplexer truth table:

SELECT STROBE DATA OUTPUTS

A B G C Y0 Y1 Y2 Y3
X X 1 X 1 1 1 1
0 0 0 1 0 1 1 1
0 1 0 1 1 0 1 1
1 0 0 1 1 1 0 1
1 1 0 1 1 1 1 0
X X X 0 1 1 1 1

Multisim 8 Component Reference Guide 6-21

TTL

6.4.42 74xx156 (Dual 2-to-4 Dec/DEMUX (OC))

This device contains two 2-to-4 decoders/demultiplexers.
Decoder/demultiplexer truth table:

SELECT STROBE DATA OUTPUTS

A B G C Y0 Y1 Y2 Y3
X X 1 X 1 1 1 1
0 0 0 1 0 1 1 1
0 1 0 1 1 0 1 1
1 0 0 1 1 1 0 1
1 1 0 1 1 1 1 0
X X X 0 1 1 1 1

6.4.43 74xx157 (Quad 2-to-1 Data Sel/MUX)

This device contains inverters and drivers to supply full on-chip data selection to the four
output gates. It presents true data.
A 4-bit word is selected from one of two sources and is routed to the four outputs.
Data selector/multiplexer truth table:

STROBE SELECT OUTPUTS

G A/B A B Y
1 X X X 0
0 0 0 X 0
0 0 1 X 1
0 1 X 0 0
0 1 X 1 1

6-22 Electronics Workbench

 74xx

6.4.44 74xx158 (Quad 2-to-1 Data Sel/MUX)

This device contains inverters and drivers to supply full on-chip data selection to the four
output gates. It presents inverted data to minimize propagation delay time.
A 4-bit word is selected from one of two sources and is routed to the four outputs.
Data selector/multiplexer truth table:

STROBE SELECT OUTPUT

G A/B A B Y
1 X X X 1
0 0 0 X 1
0 0 1 X 0
0 1 X 0 1
0 1 X 1 0

6.4.45 74xx159 (4-to-16 Dec/DEMUX (OC))

This 4-line-to-16-line decoder uses TTL circuitry to decode four binary-coded inputs into one
of sixteen mutually exclusive open-collector outputs when both the strobe inputs are low.
The demultiplexing function is performed by using the 4 input lines to address the output line,
passing data from one of the strobe inputs with the other strobe input low.

Multisim 8 Component Reference Guide 6-23

TTL

Decoder/demultiplexer truth table:

INPUTS OUTPUTS

G1 G2 D C B A 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
0 0 0 0 0 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1
0 0 0 0 1 0 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1
0 0 0 0 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1
0 0 0 1 0 0 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1
0 0 0 1 0 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1
0 0 0 1 1 0 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1
0 0 0 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1
0 0 1 0 0 0 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1
0 0 1 0 0 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1
0 0 1 0 1 0 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1
0 0 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1
0 0 1 1 0 0 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1
0 0 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1
0 0 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 1
0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0
0 1 X X X X 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 0 X X X X 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 X X X X 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

6.4.46 74xx16 (Hex INVERTER (OC))

This device contains six inverters. For correct performance, the open collector outputs require
pull-up resistors.
Logic function:
Y=A

INVERTER gate truth table:

A Y
1 0
0 1

6-24 Electronics Workbench

 74xx

6.4.47 74xx160 (Sync 4-bit Decade Counter (clr))

This synchronous, presettable decade counter features an internal carry look-ahead for fast
counting.
Decade counter truth table:
INPUTS OUTPUTS
OPERATING MODE
MR CP CEP CET PE DN QN TC
0 X X X X X 0 0 Reset (clear)
1 · X X l l 0 0
1 · X X l h 1 (1) Parallel load
1 · h h h X count (1) Count
1 X l X h X qn (1) Hold (do nothing)
1 X X l h X qn 0

1 = High voltage level

h = High voltage level one setup prior to the low-to-high clock transition
0 = Low voltage level
l = Low voltage level one setup prior to the low-to-high clock transition
qn = Lower case letters indicate the state of the referenced output prior
to the low-to-high clock transition
X = Don’t care
· = Low-to-high clock transition
(1) = The TC output is High when CET is High and the counter is at
Terminal Count (HLLH)

6.4.48 74xx161 (Sync 4-bit Bin Counter)

This synchronous, presettable binary counter features an internal carry look-ahead for fast
counting.

Multisim 8 Component Reference Guide 6-25

TTL

4-bit bin counter truth table:

INPUTS OUTPUTS OPERATING
MODE
MR CP CEP CET PE DN QN TC
0 X X X X X 0 0 Reset (clear)
1 · X X l l 0 0
1 · X X l h 1 (1) Parallel load
1 · h h h X coun (1) Count
t
1 X l X h X qn (1) Hold (do
1 X X l h X qn 0 nothing)

1 = High voltage level

h = High voltage level one setup prior to the low-to-high clock transition
0 = Low voltage level
l = Low voltage level one setup prior to the low-to-high clock transition
qn = Lower case letters indicate the state of the referenced output prior to the
low-to-high clock transition
X = Don’t care
· = Low-to-high clock transition
(1) = The TC output is High when CET is High and the counter is at Terminal
Count (HHHH)

6.4.49 74xx162 (Sync 4-bit Decade Counter)

This synchronous, presettable decade counter features an internal carry look-ahead for fast
counting.

6-26 Electronics Workbench

 74xx

Decade counter truth table:

INPUTS OUTPUTS
OPERATING
MODE
SR CP CEP CET PE DN QN TC
l · X X X X 0 0 Reset (clear)
h · X X l l 0 0
h · X X l h 1 (2) Parallel load
h · h h h X coun (2) Count
t
h X l X h X qn (2) Hold (do nothing)
h X X l h X qn 0

1 = High voltage level

h = High voltage level one setup prior to the low-to-high clock transition
0 = Low voltage level
l = Low voltage level one setup prior to the low-to-high clock transition
qn = Lower case letters indicate the state of the referenced output prior to the
low-to-high clock transition
X = Don’t care
· = Low-to-high clock transition
(2) = The TC output is High when CET is High and the counter is at Terminal
Count (HLLH)

6.4.50 74xx163 (Sync 4-bit Binary Counter)

This synchronous, presettable, 4-bit binary counter features an internal carry look-ahead for
fast counting.

Multisim 8 Component Reference Guide 6-27

TTL

6.4.51 74xx164 (8-bit Parallel-Out Serial Shift Reg)

This 8-bit shift register has gated serial inputs and an asynchronous clear.
Shift register truth table:
Clear Clk A B QA QB QH
0 X X X 0 0 0
1 0 X X QA0 QB0 QH0
1 · 1 1 1 QAn QGn
1 · 0 X 0 QAn QGn
1 · X 0 0 QAn QGn

· = positive edge-triggered
QA0, QB0, = the level of QA, QB, QH respectively before the indicated steady
QH0 state input conditions were established
QAn, QGn = the level of QA or QG before the most recent positive transition of
the clock; indicates one-bit shift.

6.4.52 74xx165 (Parallel-load 8-bit Shift Reg)

This serial shift-register shifts the data in the direction of QA toward QH when clocked. To
load the data at the 8-inputs into the device, apply a low level at the shift/load input. This
register is equipped with a complementary output at the eighth bit.
Shift register truth table:
INTERNAL
INPUTS O/P OUTPUTS

SHIFT/ PARALLEL
CLK INH CLK SERIAL QA QB QH
LOAD A B C D
0 X X X a b c d a b h
1 0 0 X X X X X QA0 QB0 QH0
1 0 · 1 X X X X 1 QAn QGn
1 0 · 0 X X X X 0 QAn QGn
1 1 X X X X X X QA0 QB0 QH0

· = transition from low to high

a,b,c,d = the level of steady state input at A, B, C, or D respectively

6-28 Electronics Workbench

 74xx

6.4.53 74xx166 (Parallel-load 8-bit Shift Reg)

This shift-register is a parallel-in or serial-in, serial out device. It shifts the data in the
direction of QA toward QH when clocked. It features an active-low clear input. To load the
data at the 8-inputs into the device, apply a low level at the shift/load input.
Shift register truth table:

INPUTS INTERNAL OUTPUTS

O/P

SHIFT/ PARALLEL
CLR CLK INH CLK SERIAL QA QB QH
LOAD A through H
0 X X X X X X X X 0 0 0
1 X 0 0 X X X X X QA0 QB0 QH0
1 0 0 · X A TO H a b 1
1 1 0 · 1 X X X X 1 QAn QGn
1 1 0 · 0 X X X X 0 QAn QGn
1 X 1 · X X X X X QA0 QB0 QH0

· = transition from low to high

a,b,c,d = the level of steady state input at A, B, C, or D respectively

6.4.54 74xx169 (Sync 4-bit up/down Binary Counter)

This synchronous presettable 4-bit binary counter has an internal carry look-ahead for
cascading in high speed counting applications.
Up/down counter truth table:

ENP ENT D/U CLK LOAD A B C D QA QB QC QD RCO

0 0 X X 0 X X X X A B C D 1*
0 0 1 · 1 X X X X Count Down 1*
0 0 0 · 1 X X X X Count Up 1*
1 X X X X X X X X Qa0 Qb0 Qc0 Qd0 1*
X 1 X X X X X X X Qa0 Qb0 Qc0 Qd0 1*

1* = during the UP count RCO goes LOW at count 15.

during the DOWN count RCO goes LOW at count 0.

Multisim 8 Component Reference Guide 6-29

TTL

6.4.55 74xx17 (Hex BUFFER (OC))

This device contains six independent BUFFER/Drivers. For correct performance, the open
collector outputs require pull-up resistors.
BUFFER gate truth table:

A Y

0 0
1 1

6.4.56 74xx173 (4-bit D-type Reg w/3-state Out)

D-type register truth table:

DATA
DATA OUTPUT
ENABLE

CLEAR CLK G1 G2 D Q
1 X X X X 0
0 0 X X X Q0
0 · 1 X X Q0
0 · X 1 X Q0
0 · 0 0 0 0
0 · 0 0 1 1

6.4.57 74xx174 (Hex D-type FF (clr))

D-type flip-flop truth table:

CLEA
CLK D Q Q
R
0 X X 0 1
1 · 1 1 0
1 · 0 0 1
1 0 X Q0 QO

6-30 Electronics Workbench

 74xx

6.4.58 74xx175 (Quad D-type FF (clr))

D-type flip-flop truth table:

CLEA
CLK D Q Q
R
0 X X 0 1
1 · 1 1 0
1 · 0 0 1
1 0 X Q0 QO

6.4.59 74xx180 (9-bit Odd/even Par GEN)

This 9-bit (8 data bits plus 1 parity bit) parity generator/checker features odd/even outputs and
control inputs to facilitate operation in either odd- or even-parity applications.
Parity generator/checker truth table:

INPUTS OUTPUTS

S OF H’s AT A S S
EVEN ODD
THRU H EVEN ODD
Even 1 0 1 0
Odd 1 0 0 1
Even 0 1 0 1
Odd 0 1 1 0
X 1 1 0 0
X 0 0 1 1

Multisim 8 Component Reference Guide 6-31

TTL

6.4.60 74xx181 (Alu/Function Generator)

ALU/function generator truth table:

ACTIVE - LOW DATA

SELECTION M=H M=L; ARITHMETIC OPERATIONS

LOGIC Cn=L Cn=H

S3 S2 S1 S0
FUNCTIONS (NO CARRY) (WITH CARRY)

0 0 0 0 F=A F= A MINUS 1 F= A
0 0 0 1 F= AB F= AB MINUS 1 F= AB
0 0 1 0 F= A+B F= AB MINUS 1 F= AB
0 0 1 1 F= 1 F= MINUS 1(2's comp) F= Zero
0 1 0 0 F= A+B F= A PLUS (A+B) F= A PLUS(A+B) Plus 1
0 1 0 1 F= B F= AB PLUS(A+B) F= AB PLUS (A+B) PLUS 1
0 1 1 0 F= A“+”B F= A MINUS B MINUS 1 F= A MINUS
0 1 1 1 F= A+B F= A+B F= (A+B)PLUS1
1 0 0 0 F= AB F= A PLUS (A+B) F= A PLUS (A+B) PLUS 1
1 0 0 1 F= A“+”B F= A PLUS B F= A PLUS B PLUS
1 0 1 0 F= B F= AB PLUS(A+B) F= AB PLUS (A+B) PLUS 1
1 0 1 1 F= A + B F= (A + B) F= (A+B) PLUS 1

6-32 Electronics Workbench

 74xx

6.4.61 74xx182 (Look-ahead Carry GEN)

The high-speed, look-ahead carry generator can anticipate a carry across four binary adders or
groups of adders. It is cascadable to perform full look-ahead across n-bit adders.

Truth table for G output:

INPUTS OUTPUT

G3 G2 G1 G0 P3 P2 P1 G
0 X X X X X X 0
X 0 X X 0 X X 0
X X 0 X 0 0 X 0
X X X 0 0 0 0 0
All other combinations 1

Truth table for P output:

INPUTS OUTPUT

P3 P2 P1 P0 P
0 0 0 0 0
All other
combinations 1

Truth table for Cn+x output:

INPUTS OUTPUT

G0 P0 Cn Cn+x
0 X X 1
X 0 1 1
All other
combinations 0

Multisim 8 Component Reference Guide 6-33

TTL

Truth table for Cn+y output:

INPUTS OUTPUT

G1 G0 P1 P0 Cn Cn+y
0 X X X X 1
X 0 0 X X 1
X X 0 0 1 1
All other
combinations 0

Truth table for Cn+z output:

INPUTS OUTPUT

G2 G1 G0 P2 P1 P0 Cn Cn+z
0 X X X X X X 1
X 0 X 0 X X X 1
X X 0 0 0 X X 1
X X X 0 0 0 1 1
All other combinations 0

1 = High level
0 = Low level
X = Don’t care

6-34 Electronics Workbench

 74xx

6.4.62 74xx190 (Sync BCD up/down Counter)

This device is a synchronous, BCD, reversible up/down counter.

Counter TC and RC truth table:

TERMINAL COUNT
INPUTS OUTPUTS
STATE

U/D CE CP Q0 Q1 Q2 Q3 TC RC
1 1 X 1 X X 1 0 1
0 1 X 1 X X 1 1 1
0 0 1 X X 1 1
0 1 X 0 0 0 0 0 1
1 1 X 0 0 0 0 1 1
1 0 0 0 0 0 1

1 = High voltage level

0 = Low voltage level
X = Don’t care
= Low pulse

Multisim 8 Component Reference Guide 6-35

TTL

6.4.63 74xx191 (Sync 4-bit up/down Counter)

This device is a synchronous, 4-bit binary, reversible up/down counter.

Counter TC and RC truth table:

TERMINAL COUNT
INPUTS OUTPUTS
STATE

U/D CE CP Q0 Q1 Q2 Q3 TC RC
1 1 X 1 1 1 1 0 1
0 1 X 1 1 1 1 1 1
0 0 1 1 1 1 1
0 1 X 0 0 0 0 0 1
1 1 X 0 0 0 0 1 1
1 0 0 0 0 0 1

1 = High voltage level

0 = Low voltage level
X = Don’t care
= Low pulse

6.4.64 74xx192 (Sync BCD Up/down Counter)

This device is a synchronous, BCD, reversible up/down counter.

6-36 Electronics Workbench

 74xx

Up/down counter truth table:

INPUTS OUTPUTS
OPERATING
MODE
MR PL CPU CPD D0 D1 D2 D3 Q0 Q1 Q2 Q3 TCU TCD
1 X X 0 X X X X 0 0 0 0 1 0 Reset
1 X X 1 X X X X 0 0 0 0 1 1
0 0 X 0 0 0 0 0 0 0 0 0 1 0 Parallel load
0 0 X 1 0 0 0 0 0 0 0 0 1 1
0 0 0 X 1 X X 1 Qn=Dn 0 1
0 0 1 X 1 X X 1 Qn=Dn 1 1
0 1 · 1 X X X X Count up 11 1 Count up
0 1 1 · X X X X Count down 1 12 Count down

· = transition from low to high

11 = TCU=CPU at terminal count up (HLLH)
12 = TCD=CPD at terminal count down (LLLL)

6.4.65 74xx193 (Sync 4-bit Bin Up/down Counter)

This device is a synchronous, 4-bit binary, reversible up/down counter.
Up/down counter truth table:

INPUTS OUTPUTS
OPERATING
MODE
MR PL CPU CPD D0 D1 D2 D3 Q0 Q1 Q2 Q3 TCU TCD
1 X X 0 X X X X 0 0 0 0 1 0 Reset
1 X X 1 X X X X 0 0 0 0 1 1
0 0 X 0 0 0 0 0 0 0 0 0 1 0
0 0 X 1 0 0 0 0 0 0 0 0 1 1 Parallel load
0 0 0 X 1 1 1 1 1 1 1 1 0 1
0 0 1 X 1 1 1 1 1 1 1 1 1 1
0 1 · 1 X X X X Count up 11 1 Count up
0 1 1 · X X X X Count down 1 12 Count down

· = transition from low to high

11 = TCU=CPU at terminal count up (HHHH)
12 = TCD=CPD at terminal count down (LLLL)

Multisim 8 Component Reference Guide 6-37

TTL

6.4.66 74xx194 (4-bit Bidirect Univ. Shift Reg)

This bidirectional shift register has parallel-inputs, parallel outputs, right-shift and left-shift
serial inputs, operating-mode-control inputs, and a direct overriding clear line.
Shift register truth table:

MODE SERIAL PARALLEL OUTPUTS

CLEAR S1 S0 CLK LEFT RIGHT A B C D QA QB QC QD

0 X X X X X X X X X 0 0 0 0
1 X X 0 X X X X X X QA0 QB0 QC0 QD0
1 1 1 · X X a b c d a b c d
1 0 1 · X 1 X X X X 1 QAn QBn QCn
1 0 1 · X 0 X X X X 0 QAn QBn QCn
1 1 0 · 1 X X X X X QBn QCn QDn 1
1 1 0 · 0 X X X X X QBn QCn QDn 0
1 0 0 X X X X X X X QA0 QB0 QC0 QD0

· = transition from low to high

a, b, c, d = the level of steady state input at inputs A, B, C, or D respectively
QA0, QB0, QC0, = the level of QA, QB, QC, or QD, respectively, before the indicated steady state
QD0 input conditions were established
QAn, QBn, QCn, = the level of QA, QB, QC, or QD before the most recent negative transition of
QDn the clock

6.4.67 74xx195 (4-bit Parallel-Access Shift Reg)

This 4-bit register has parallel inputs, parallel outputs, J-K serial inputs, shift/load control
input, and a direct overriding clear.

6-38 Electronics Workbench

 74xx

Shift register truth table:

SERIAL PARALLEL OUTPUTS

SHIFT/
CLEAR CLK J K A B C D QA QB QC QD QD
LOAD
0 X X X X X X X X 0 0 0 0 1
1 0 · X X a b c d a b c d d
1 1 0 X X X X X X QA0 QB0 QC0 QD0 QD0
1 1 · 0 1 X X X X QA0 QA0 QBn QCn QCn
1 1 · 0 0 X X X X 0 QAn QBn QCn QCn
1 1 · 1 1 X X X X 1 QAn QBn QCn QCn
1 1 · 1 0 X X X X QAn QAn QBn QCn QCn

· = transition from low to high

a, b, c, d = the level of steady state input at inputs A, B, C, or D respectively
QA0, QB0, QC0, = the level of QA, QB, QC, or QD, respectively, before the indicated steady state
QD0 input conditions were established
QAn, QBn, QCn = the level of QA, QB, QC before the most recent negative transition of the clock

6.4.68 74xx198 (8-bit Shift Reg (shl/shr ctrl))

This bidirectional register has parallel inputs, parallel outputs, right-shift and left-shift serial
inputs, operating-mode-control inputs, and a direct overriding clear line.
Shift register truth table:

MODE SERIAL PARALLEL OUTPUTS

CLEAR S1 S0 CLK LEFT RIGHT A ... h QA QB ... QG QH

0 X X X X X X 0 0 0 0
1 X X 0 X X X QA0 QB0 QG0 QH0
1 1 1 · X X a...h a b g h
1 0 1 · X 1 X 1 QAn QFn QGn
1 0 1 · X 0 X 0 QAn QFn QGn
1 1 0 · 1 X X QBn QCn QHn 1
1 1 0 · 0 X X QBn QCn QHn 1
1 0 0 X X X X QA0 QB0 QG0 QH0

Multisim 8 Component Reference Guide 6-39

TTL

· = transition from low to high

a ... h = the level of steady state input at inputs A through H respectively
QA0, QB0, QG0, = the level of QA, QB, QG, or QH, respectively, before the indicated steady state
QH0 input conditions were established
QAn, QBn, etc. = the level of QA, QB etc., respectively, before the most recent negative
transition of the clock

6.4.69 74xx199 (8-bit Shift Reg (sh/ld ctrl))

This device contains an 8-bit shift register with shift/load control.
Shift register truth table:

MODE SERIAL

PARALLEL OUTPUTS

QB..Q
CLEAR S/L CLKINH CLK J K A...H QA QH
G
0 X X X X X X 0 0 0
1 X 0 0 X X X QA0 QB0 QH0
1 0 0 · X X a...h a b..g h
1 1 0 · 0 1 X QA0 QA0 QGn
1 1 0 · 0 0 X 0 QAn QGn
1 1 0 · 1 1 X 1 QCn 1
1 1 0 · 1 0 X QAn QAn QGn
1 X 1 · X X X QA0 QB0 QH0

· = transition from low level to high level

a ... h = the level of steady state input at inputs A through H respectively
QA0, QB0, QG0, = the level of QA, QB, QG, or QH, respectively, before the indicated steady state
QH0 input conditions were established
QAn, QBn, etc. = the level of QA, QB etc., respectively, before the most recent negative
transition of the clock

6-40 Electronics Workbench

 74xx

6.4.70 74xx20 (Dual 4-In NAND)

This device contains two independent 4-input NAND gates.
Logic function:
Y = ABCD

NAND gate truth table

A B C D Y
1 1 1 1 0
0 X X X 1
X 0 X X 1
X X 0 X 1
X X X 0 1

6.4.71 74xx21 (Dual 4-In AND)

This device contains two independent 4-input AND gates.
Logic function:
Y = ABCD

AND gate truth table:

A B C D Y
1 1 1 1 1
0 X X X 0
X 0 X X 0
X X 0 X 0
X X X 0 0

Multisim 8 Component Reference Guide 6-41

TTL

6.4.72 74xx22 (Dual 4-In NAND (OC))

This device contains two independent 4-input NAND gates. For correct performance, the
open collector outputs require pull-up resistors.
Logic function:
Y = ABCD

NAND gate truth table:

A B C D Y
1 1 1 1 0
0 X X X 1
X 0 X X 1
X X 0 X 1
X X X 0 1

6.4.73 74xx238 (3-to-8 line Dec/DEMUX)

The logic levels at the C B and A inputs select one of the eight lines. G1 is an active-high
enable input while G2A and G2B are active-low enable inputs.
3-to-8 decoder/demultiplexer truth table:

SELECT OUTPUTS

G1 G2A G2B C B A Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7
X 1 X X X X 0 0 0 0 0 0 0 0
X X 1 X X X 0 0 0 0 0 0 0 0
0 X X X X X 0 0 0 0 0 0 0 0
1 0 0 0 0 0 1 0 0 0 0 0 0 0
1 0 0 0 0 1 0 1 0 0 0 0 0 0
1 0 0 0 1 0 0 0 1 0 0 0 0 0
1 0 0 0 1 1 0 0 0 1 0 0 0 0
1 0 0 1 0 0 0 0 0 0 1 0 0 0
1 0 0 1 0 1 0 0 0 0 0 1 0 0
1 0 0 1 1 0 0 0 0 0 0 0 1 0
1 0 0 1 1 1 0 0 0 0 0 0 0 1

6-42 Electronics Workbench

 74xx

6.4.74 74xx24 (Dual 4-input NAND Schmitt)

Each circuit in this device functions as a NAND gate or inverter. Due to the Schmitt action,
there are different input threshold levels for positive-going and negative-going signals.

6.4.75 74xx240 (Octal BUFFER w/3-state Out)

This device has high fan-out, improved fan-in, and 400-mV noise margin.
Octal BUFFER gate truth table:

G A Y
1 X Z
0 0 1
0 1 0

Z = High impedance (off)

6.4.76 74xx241 (Octal BUFFER w/3-state Out)

This device has high fan-out, improved fan-in, and 400-mV noise margin.
Octal BUFFER gate truth table:

INPUTS OUTPUTS

G A1 A2 A3 A4 Y1 Y2 Y3 Y4
1 X X X X Z Z Z Z
0 X X X X A1 A2 A3 A4

Z = High impedance (off)

A1, A2... = The level of the respective input

6.4.77 74xx244 (Octal BUFFER w/3-state Out)

This device has high fan-out, improved fan-in, and 400-mV noise margin.

Multisim 8 Component Reference Guide 6-43

TTL

Octal BUFFER gate truth table:

INPUTS OUTPUTS

G A1 A2 A3 A4 Y1 Y2 Y3 Y4
1 X X X X Z Z Z Z
0 X X X X A1 A2 A3 A4

Z = High impedance (off)

A1, A2... = The level of the respective input

6.4.78 74xx246 (BCD-to-seven segment dec)

The BCD-to-seven-segment decoder/driver features active-low outputs designed for driving
indicators directly. It has full ripple-blanking input/output controls and a lamp test input.
BCD-to-seven-segment decoder/driver truth table:

6-44 Electronics Workbench

 74xx

Notes:
1. The blanking input (BI) must be open or held at a high logic level when output
functions 0 through 15 are desired. The ripple-blanking input (RBI) must be open or
high if blanking of a decimal zero is not desired.
2. When a low logic level is applied to the blanking input (BI), all segment outputs are
off regardless of any other input.
3. When ripple-blanking input (RBI) and inputs A, B, C, and D are at a low level with
the lamp test input high, all segment outputs go off and the ripple-blanking output
(RBO) goes to a low level (response condition).
4. When the blanking input/ripple-blanking output (BI/RBO) is open or held high and a
low is applied to the lamp-test input, all segment outputs are on.

6.4.79 74xx247 (BCD-to-seven segment dec)

The BCD -to-seven-segment decoder/driver features active-low outputs designed for driving
indicators directly. It has full ripple-blanking input/output controls and a lamp test input.
BCD-to-seven-segment decoder/driver truth table:

Multisim 8 Component Reference Guide 6-45

TTL

Notes:
1. The blanking input (BI) must be open or held at a high logic level when output
functions 0 through 15 are desired. The ripple-blanking input (RBI) must be open or
high if blanking of a decimal zero is not desired.
2. When a low logic level is applied to the blanking input (BI), all segment outputs are off
regardless of any other input.
3. When ripple-blanking input (RBI) and inputs A, B, C, and D are at a low level with the
lamp test input high, all segment outputs go off and the ripple-blanking output (RBO)
goes to a low level (response condition).
4. When the blanking input/ripple-blanking output (BI/RBO) is open or held high and a
low is applied to the lamp-test input, all segment outputs are on.

6.4.80 74xx248 (BCD-to-seven segment dec)

The BCD -to-seven-segment decoder/driver features active-high outputs for driving lamp
buffers. It has full ripple-blanking input/output controls and a lamp test input.

6-46 Electronics Workbench

 74xx

BCD-to-seven-segment decoder/driver truth table:

DECIMAL INPUTS OUTPUTS NOTE

BI/
OR
RBO
FUNCTION LT RBI D C B A a b c d e f g
0 1 1 0 0 0 0 1 1 1 1 1 1 1 0 1
1 1 X 0 0 0 1 1 0 1 1 0 0 0 0 1
2 1 X 0 0 1 0 1 1 1 0 1 1 0 1
3 1 X 0 0 1 1 1 1 1 1 1 0 0 1
4 1 X 0 1 0 0 1 0 1 1 0 0 1 1
5 1 X 0 1 0 1 1 1 0 1 1 0 1 1
6 1 X 0 1 1 0 1 1 0 1 1 1 1 1
7 1 X 0 1 1 1 1 1 1 1 0 0 0 0 1
8 1 X 1 0 0 0 1 1 1 1 1 1 1 1
9 1 X 1 0 0 1 1 1 1 1 1 0 1 1
10 1 X 1 0 1 0 1 0 0 0 1 1 0 1
11 1 X 1 0 1 1 1 0 0 1 1 0 0 1
12 1 X 1 1 0 0 1 0 1 0 0 0 1 1
13 1 X 1 1 0 1 1 1 0 0 1 0 1 1
14 1 X 1 1 1 0 1 0 0 0 1 1 1 1
15 1 X 1 1 1 1 1 0 0 0 0 0 0 0
BI X X X X X X 0 0 0 0 0 0 0 0 2
RBI 1 0 0 0 0 0 0 0 0 0 0 0 0 0 3
LT 0 X X X X X 1 1 1 1 1 1 1 1 4

Notes:
1. The blanking input (BI) must be open or held at a high logic level when output
functions 0 through 15 are desired. The ripple-blanking input (RBI) must be open or
high if blanking of a decimal zero is not desired.
2. When a low logic level is applied to the blanking input (BI), all segment outputs are
low regardless of any other input.
3. When ripple-blanking input (RBI) and inputs A, B, C, and D are at a low level with
the lamp test input high, all segment outputs go low and the ripple-blanking output
(RBO) goes to a low level (response condition).
4. When the blanking input/ripple-blanking output (BI/RBO) is open or held high and
a low is applied to the lamp-test input, all segment outputs are high.

Multisim 8 Component Reference Guide 6-47

TTL

6.4.81 74xx249 (BCD-to-seven segment dec)

The BCD -to-seven-segment decoder/driver features active-high outputs for driving lamp
buffers. It has full ripple-blanking input/output controls and a lamp test input.
BCD-to-seven-segment decoder/driver truth table:

DECIMAL INPUTS OUTPUTS NOTE

OR BI/RBO
FUNCTION LT RBI D C B A a b c d e f g
0 1 1 0 0 0 0 1 1 1 1 1 1 1 0 1
1 1 X 0 0 0 1 1 0 1 1 0 0 0 0 1
2 1 X 0 0 1 0 1 1 1 0 1 1 0 1
3 1 X 0 0 1 1 1 1 1 1 1 0 0 1
4 1 X 0 1 0 0 1 0 1 1 0 0 1 1
5 1 X 0 1 0 1 1 1 0 1 1 0 1 1
6 1 X 0 1 1 0 1 1 0 1 1 1 1 1
7 1 X 0 1 1 1 1 1 1 1 0 0 0 0 1
8 1 X 1 0 0 0 1 1 1 1 1 1 1 1
9 1 X 1 0 0 1 1 1 1 1 1 0 1 1
10 1 X 1 0 1 0 1 0 0 0 1 1 0 1
11 1 X 1 0 1 1 1 0 0 1 1 0 0 1
12 1 X 1 1 0 0 1 0 1 0 0 0 1 1
13 1 X 1 1 0 1 1 1 0 0 1 0 1 1
14 1 X 1 1 1 0 1 0 0 0 1 1 1 1
15 1 X 1 1 1 1 1 0 0 0 0 0 0 0
BI X X X X X X 0 0 0 0 0 0 0 0 2
RBI 1 0 0 0 0 0 0 0 0 0 0 0 0 0 3
LT 0 X X X X X 1 1 1 1 1 1 1 1 4

6-48 Electronics Workbench

 74xx

Notes:
1. The blanking input (BI) must be open or held at a high logic level when output
functions 0 through 15 are desired. The ripple-blanking input (RBI) must be open or
high if blanking of a decimal zero is not desired.
2. When a low logic level is applied to the blanking input (BI), all segment outputs are
low regardless of any other input.
3. When ripple-blanking input (RBI) and inputs A, B, C, and D are at a low level with
the lamp test input high, all segment outputs go low and the ripple-blanking output
(RBO) goes to a low level (response condition).
4. When the blanking input/ripple-blanking output (BI/RBO) is open or held high and a
low is applied to the lamp-test input, all segment outputs are high.

6.4.82 74xx25 (Dual 4-In NOR w/Strobe)

This device contains two independent 4-input NOR gates with strobe.
NOR gate with strobe truth table:

A B C D G Y
1 X X X 1 0
X 1 X X 1 0
X X 1 X 1 0
X X X 1 1 0
0 0 0 0 X 1
X X X X 0 1

6.4.83 74xx251 (Data Sel/MUX w/3-state Out)

This device contains full on-chip binary decoding to select one-of-eight data sources and has a
strobe-controlled three-state output.

Multisim 8 Component Reference Guide 6-49

TTL

Data selector/multiplexer truth table:

INPUTS OUTPUTS

SELECT STROBE
Y W
C B A S
X X X 1 Z Z
0 0 0 0 D0 D0
0 0 1 0 D1 D1
0 1 0 0 D2 D2
0 1 1 0 D3 D3
1 0 0 0 D4 D4
1 0 1 0 D5 D5
1 1 0 0 D6 D6
1 1 1 0 D7 D7

Z = high impedance (off)

D0, D1...D7 = level of the respective D input

6.4.84 74xx253 (Dual 4-to-1 Data Sel/MUX w/3-state Out)

This Schottky-clamped data selector/multiplexer contains inverters and drivers to supply fully
complementary on-chip, binary decoding data selection to the AND-OR gates.
Data selector/multiplexer truth table:

XB A C0 C1 C2 C3 G Y
X X X X X X 1 Z
0 0 0 X X X 0 0
0 0 1 X X X 0 1
0 1 X 0 X X 0 0
0 1 X 1 X X 0 1
1 0 X X 0 X 0 0
1 0 X X 1 X 0 1
1 1 X X X 0 0 0
1 1 X X X 1 0 1

Z = High impedance (off)

6-50 Electronics Workbench

 74xx

6.4.85 74xx257 (Quad 2-to-1 line Data Sel/MUX)

This device is designed to multiplex signals from 4-bit data sources to 4-output data lines in
bus-organized systems. Its 3-state outputs interface directly with the system bus.
Data selector/multiplexer truth table:

OUTPUT
SELECT A B Y
CONTROL
1 X X X Z
0 0 0 X 0
0 0 1 X 1
0 1 X 0 0
0 1 X 1 1

Z = High impedance (off)

6.4.86 74xx258 (Quad 2-to-1 line Data Sel/MUX)

This device is designed to multiplex signals from 4-bit data sources to 4-output data lines in
bus-organized systems. Its 3-state outputs interface directly with the system bus.
Data selector/multiplexer truth table:

OUTPUT
SELECT A B Y
CONTROL
1 X X X Z
0 0 0 X 0
0 0 1 X 1
0 1 X 0 0
0 1 X 1 1

Z = High impedance (off)

Multisim 8 Component Reference Guide 6-51

TTL

6.4.87 74xx259 (8-bit Latch)

This 8-bit addressable latch is a 1-of-8 decoder or demultiplexer with active high outputs. It
stores single-line data in eight addressable latches.
8-bit addressable latch truth table:

INPUTS OUTPUT OF EACH

ADDRESSED OTHER FUNCTION
CLEAR G LATCH OUTPUT
1 0 D Qi0 Addressable latch
1 1 Qi0 Qi0 Memory
0 0 D 0 8-line demultiplexer
0 1 0 0 Clear

6.4.88 74xx26 (Quad 2-In NAND (OC))

This device contains four independent 2-input NAND gates.
Logic function:
Y = ABCD

NAND gate truth table:

A B C D Y
1 1 1 1 0
0 X X X 1
X 0 X X 1
X X 0 X 1
X X X 0 1

6.4.89 74xx266 (Quad 2-In XNOR (OC))

This device contains four independent 2-input EXCLUSIVE-NOR gates.
Logic function:
Y = A⊕B

6-52 Electronics Workbench

 74xx

Exclusive-NOR gate truth table:

A B Y
0 0 1
0 1 0
1 0 0
1 1 1

6.4.90 74xx27 (Tri 3-In NOR)

This device contains three independent 3-input NOR gates.
Logic function:
Y = A+B+C

NOR gate truth table:

A B C Y
0 0 0 1
1 0 0 0
0 1 0 0
1 1 0 0
0 0 1 0
1 0 1 0
0 1 1 0
1 1 1 0

Multisim 8 Component Reference Guide 6-53

TTL

6.4.91 74xx273 (Octal D-type FF)

D flip-flop truth table

CLEAR CLK D Q
0 X X 0
1 · 1 1
1 · 0 0
1 0 X Q0

· = transition from low to high

6.4.92 74xx279 (Quad SR latches)

The RS flip-flop has an undesired operating condition, where 1 levels at both inputs will cause
both outputs to go to a 0 level. This undefined condition must be avoided. Circuits involving
feedback will lead to a “race condition” where the output will be unpredictable.
RS flip-flop truth table:

S R Q Q
0 0 - - (no change)
0 1 0 1
1 0 1 0
1 1 X X (undefined)

6.4.93 74xx28 (Quad 2-In NOR)

This device contains four independent 2-input NOR gates.
Logic function:
Y = A+B

6-54 Electronics Workbench

 74xx

NOR gate truth table:

A B Y
0 0 1
1 0 0
0 1 0
1 1 0

6.4.94 74xx280 (9-bit odd/even parity generator/checker)

9-bit odd/even parity generator/checker truth table:

NUMBER OF INPUTS

Σ - Σ-
A THROUGH I THAT ARE HIGH
EVEN ODD
0, 2, 4, 6, 8 1 0
1, 3, 5, 7, 9 0 1

Σ = sigma

6.4.95 74xx283 (4-bit Bin Full Add)

This device performs the addition of two 4-bit binary numbers. It features full internal look-
ahead across all four bits generating the carry term in ten nanoseconds typically.

6.4.96 74xx290 (Decade Counter)

This device contains four master-slave flip-flops and additional gating to provide a divide-by-
two counter and a three-stage binary counter for which the count cycle length is divide-by-
five.

Multisim 8 Component Reference Guide 6-55

TTL

Decade counter truth table:

COUNT QD QC QB QA R0(1) R0(2) R9(1) R9(2) QD QC QB QA

0 0 0 0 0 1 1 0 X 0 0 0 0
1 0 0 0 1 1 1 X 0 0 0 0 0
2 0 0 1 0 X X 1 1 1 0 0 1
3 0 0 1 1 X 0 X 0 COUNT
4 0 1 0 0 0 X 0 X COUNT
5 0 1 0 1 0 X X 0 COUNT
6 0 1 1 0 X 0 0 X COUNT
7 0 1 1 1
8 1 0 0 0
9 1 0 0 1

6.4.97 74xx293 (4-bit Binary Counter)

This device contains four master-slave flip-flops and additional gating to provide a divide-by-
two counter and a three-stage binary counter for which the count cycle length is divide-by-
eight.
Counter truth table:
RESET IN OUTPUT

Ro1 Ro2 Qd Qc Qb Qa
1 1 0 0 0 0
0 X COUNT
X 0 COUNT

6.4.98 74xx298 (Quad 2-In MUX)

This quadruple two-input multiplexer selects one of two 4-bit data sources and stores data
synchronously with system clock.

6-56 Electronics Workbench

 74xx

Multiplexer truth table:

WORD
CLK QA QB QC QD
SELECT
0 Ø a1 b1 c1 d1
1 Ø a2 b2 c2 d2
X Ø QA0 QB0 QC0 QD0

‚ = transition from high to low

a1, a2, etc. = the level of steady state input at A1, A2, etc.
QA0, QB0, etc. = the level of QA, QB, etc.entered on the most recent negative
transition of the clock input

6.4.99 74xx30 (8-In NAND)

Logic function:
Y = ABCDEFGH

8-input NAND gate truth table:

INPUTS A THROUGH H Y
All inputs 1 0
One or more inputs 0 1

6.4.10074xx32 (Quad 2-In OR)

This device contains four independent 2-input OR gates.
Logic function:
Y = A+B

Multisim 8 Component Reference Guide 6-57

TTL

OR gate truth table:

A B Y
0 0 0
1 0 1
0 1 1
1 1 1

6.4.10174xx33 (Quad 2-In NOR (OC))

This device contains four independent 2-input NOR gates. For correct performance, the open
collector outputs require pull-up resistors.
Logic function:
Y = A+B

NOR gate truth table:

A B Y
0 0 1
1 0 0
0 1 0
1 1 0

6.4.10274xx350 (4-bit Shifter w/3-state Out)

This device shifts 4-bits of data to 0, 1, 2, or 3 places under control of two select lines.

6-58 Electronics Workbench

 74xx

4-bit shifter truth table:

INPUTS OUTPUTS

OE S1 S0 Y0 Y1 Y2 Y3
1 X X Z Z Z Z
0 0 0 D0 D1 D2 D3
0 0 1 D-1 D0 D1 D2
0 1 0 D-2 D-1 D0 D1
0 1 1 D-3 D-2 D-1 D0

Z = High impedance (off)

6.4.10374xx351 (Dual Data Sel/MUX w/3-state Out)

The 74351 device is made up of two 8-line-to-1-line data selectors/multiplexors with full
decoding on one monolithic chip.
Dual data selector/multiplexor truth table:

INPUTS OUTPUTS

ENABLE SELECT
1Y 2Y
G C B A
1 X X X Z Z
0 0 0 0 1D0 2D0
0 0 0 1 1D1 2D1
0 0 1 0 1D2 2D2
0 0 1 1 1D3 2D3
0 X 0 0 D4 D4
0 X 0 1 D5 D5
0 X 1 0 D6 D6
0 X 1 1 D7 D7

6.4.10474xx352 (Dual 4-to-1 Data Sel/MUX)

This device contains inverters and drivers to supply fully complementary on-chip, binary
decoding data selection to the AND-OR-invert gates.

Multisim 8 Component Reference Guide 6-59

TTL

Data selector/multiplexer truth table:

SELECT DATA INPUTS

B A C0 C1 C2 C3 G Y
X X X X X X 1 1
0 0 0 X X X 0 1
0 0 1 X X X 0 0
0 1 X 0 X X 0 1
0 1 X 1 X X 0 0
1 0 X X 0 X 0 1
1 0 X X 1 X 0 0
1 1 X X X 0 0 1
1 1 X X X 1 0 0

6.4.10574xx353 (Dual 4-to-1 Data Sel/MUX w/3-state Out)

This device contains inverters and drivers to supply fully complementary on-chip, binary
decoding data selection to the AND-OR-invert gates.
Data selector/multiplexer truth table:

SELECT DATA INPUTS

B A C0 C1 C2 C3 G Y
X X X X X X 1 1
0 0 0 X X X 0 1
0 0 1 X X X 0 0
0 1 X 0 X X 0 1
0 1 X 1 X X 0 0
1 0 X X 0 X 0 1
1 0 X X 1 X 0 0
1 1 X X X 0 0 1
1 1 X X X 1 0 0

6.4.10674xx365 (Hex Buffer/Driver w/3-state)

This device features high fan-out, improved fan-in, and can be used to drive terminated lines
down to 133 ohms.

6-60 Electronics Workbench

 74xx

Hex buffer/driver truth table:

INPUTS OUTPUTS

OE0 OE1 In Yn Yn
0 0 0 0 1
0 0 1 1 0
X 1 X Z Z
1 X X Z Z

1 = High voltage level

0 = Low voltage level
X = Don’t care
Z = high impedance “off” state

6.4.10774xx366 (Hex Inverter Buffer/Driver w/3-state)

This device is a 3-state Hex inverter buffer/driver.
Hex inverter buffer/driver truth table:

INPUTS OUTPUTS

OE0 OE1 In Yn Yn
0 0 0 0 1
0 0 1 1 0
X 1 X Z Z
1 X X Z Z

1 = High voltage level

0 = Low voltage level
X = Don’t care
Z = High impedance “off” state

6.4.10874xx367 (Hex Buffer/Driver w/3-state)

This device features high fan-out, improved fan-in, and can be used to drive terminated lines
down to 133 ohms.

Multisim 8 Component Reference Guide 6-61

TTL

Hex buffer/driver truth table:

INPUTS OUTPUTS

OEn In Yn Yn
0 0 0 1
0 1 1 0
1 X Z Z

1 = High voltage level

0 = Low voltage level
X = Don’t care
Z = High impedance “off” state

6.4.10974xx368 (Hex Inverter Buffer/Driver w/3-state)

This device is a 3-state hex inverter buffer/driver.
Hex inverter buffer/driver truth table:

INPUTS OUTPUTS

OEn In Yn Yn
0 0 0 1
0 1 1 0
1 X Z Z

1 = High voltage level

0 = Low voltage level
X = Don’t care
Z = High impedance “off” state

6.4.11074xx37 (Quad 2-In NAND)

This device contains four independent 2-input NAND gates.
Logic function:
Y = AB

6-62 Electronics Workbench

 74xx

NAND gate truth table:

A B Y
0 0 1
1 0 1
0 1 1
1 1 0

6.4.111 74xx373 (Octal D-type Transparent Latches)

This 8-bit register features three-state bus-driving outputs and transparent D-type latches.
D-latch and flip-flop truth table:

OUTPUT ENABLE

ENABLE LATCH D OUTPUT

0 1 1 1
0 1 0 0
0 0 X Q0
1 X X Z

Z = High impedance (off)

6.4.11274xx374 (Octal D-type FF (+edge))

This 8-bit register features three-state bus-driving outputs and transparent D-type flip-flops.

Multisim 8 Component Reference Guide 6-63

TTL

D-latch and flip-flop truth table:

OUTPUT ENABLE

ENABLE LATCH D OUTPUT

0 · 1 1
0 · 0 0
0 0 X Q0
1 X X Z

Z = High impedance (off)

· = Transition from low to high

6.4.11374xx375 (4-bit Bistable Latches)

This device features outputs from a 4-bit latch.
Bistable latch truth table:

D C Q Q
0 1 0 1
1 1 1 0
X 0 Q0 Q0

6.4.11474xx377 (Octal D-type FF w/en)

This device contains eight flip-flops with single-rail outputs.
D-type flip-flop truth table:

G CLK DATA Q Q

1 X X Q0 Q0
0 · 1 1 0
0 · 0 0 1
X 0 X QO Q0

6-64 Electronics Workbench

 74xx

6.4.11574xx378 (Hex D-type FF w/en)

This device contains six flip-flops with single-rail outputs.
D-type flip-flop truth table:

G CLK DATA Q Q

1 X X Q0 Q0
0 · 1 1 0
0 · 0 0 1
X 0 X QO Q0

6.4.11674xx379 (Quad D-type FF w/en)

This device contains four flip-flops with double-rail outputs.
D-type flip-flop truth table:

INPUTS OUTPUTS

G CLK DATA Q Q

1 X X Q0 Q0
0 · 1 1 0
0 · 0 0 1
X 0 X Q0 Q0

6.4.11774xx38 (Quad 2-In NAND (OC))

This device contains four independent 2-input NAND gates. For correct performance, the
open collector outputs require pull-up resistors.
Logic function:
Y = AB

Multisim 8 Component Reference Guide 6-65

TTL

NAND gate truth table:

A B Y
0 0 1
1 0 1
0 1 1
1 1 0

6.4.11874xx39 (Quad 2-In NAND (OC))

This device contains four independent 2-input NAND gates. For correct performance, the
open collector outputs require pull-up resistors.
Logic function:
Y = AB

NAND gate truth table:

A B Y
0 0 1
1 0 1
0 1 1
1 1 0

6.4.11974xx390 (Dual Div-by-2, Div-by-5 Counter)

The 74390 device incorporates dual divide-by-two and divide-by-five counters.

6-66 Electronics Workbench

 74xx

BCD count sequence truth table:

OUTPUT
COUNT
QD QC QB QA
0 0 0 0 0
1 0 0 0 1
2 0 0 1 0
3 0 0 1 1
4 0 1 0 0
5 0 1 0 1
6 0 1 1 0
7 0 1 1 1
8 1 0 0 0
9 1 0 0 1

Notes:
Output QA is connected to input B for BCD count.

Bi-quinary truth table:

OUTPUT
COUNT
QA QD QC QB
0 0 0 0 0
1 0 0 0 1
2 0 0 1 0
3 0 0 1 1
4 0 1 0 0
5 1 0 0 0
6 1 0 0 1
7 1 0 1 0
8 1 0 1 1
9 1 1 0 0

Notes:
Output QD is connected to input A for bi-quinary.

Multisim 8 Component Reference Guide 6-67

TTL

6.4.12074xx393 (Dual 4-bit Binary Counter)

This device features an independent active-high clear and clock input for each counter. The
74393 is ideal for circuits that require two independent counters.
The 74393 counts from 0 to 15 in binary on every positive transition (low to high) of the clock
pulse.

Count sequence truth table:

OUTPUT
COUNT
QD QC QB QA
0 0 0 0 0
1 0 0 0 1
2 0 0 1 0
3 0 0 1 1
4 0 1 0 0
5 0 1 0 1
6 0 1 1 0
7 0 1 1 1
8 1 0 0 0
9 1 0 0 1
10 1 0 1 0
11 1 0 1 1
12 1 1 0 0
13 1 1 0 1
14 1 1 1 0
15 1 1 1 1

6-68 Electronics Workbench

 74xx

6.4.12174xx395 (4-bit Cascadable Shift Reg w/3-state

Out)
This device is a 4-bit shift register with 3-state outputs. It features parallel-in and parallel out
registers.
4-bit shift register truth table:

OC CLR LD/SH CLK SER A B C D QA QB QC QD QD

0 X X X X X X X X Z Z Z Z QD
1 0 X X X X X X X 0 0 0 0 0
1 1 1 1 X X X X X NO CHANGE
1 1 1 Ø X A B C D QA QB QC QD QD
1 1 0 1 X X X X X NO CHANGE
1 1 0 Ø 1 X X X X 1 QA QB QC QC
1 1 0 Ø 0 X X X X 0 QA QB QC QC

6.4.12274xx40 (Dual 4-In NAND)

This device contains two independent 4-input NAND gate.
Logic function:
Y = ABCD

NAND gate truth table:

INPUTS OUTPUT

A B C D Y
1 1 1 1 0
0 X X X 1
X 0 X X 1
X X 0 X 1
X X X 0 1

Multisim 8 Component Reference Guide 6-69

TTL

6.4.12374xx42 (4-BCD to 10-Decimal Dec)

This BCD-to-decimal decoder consists of eight inverters and ten four-input NAND gates.

4-line to 10-line decimal decoder truth table:

BCD INPUT DECIMAL OUTPUT

No. D C B A 0 1 2 3 4 5 6 7 8 9
0 0 0 0 0 0 1 1 1 1 1 1 1 1 1
1 0 0 0 1 1 0 1 1 1 1 1 1 1 1
2 0 0 1 0 1 1 0 1 1 1 1 1 1 1
3 0 0 1 1 1 1 1 0 1 1 1 1 1 1
4 0 1 0 0 1 1 1 1 0 1 1 1 1 1
5 0 1 0 1 1 1 1 1 1 0 1 1 1 1
6 0 1 1 0 1 1 1 1 1 1 0 1 1 1
7 0 1 1 1 1 1 1 1 1 1 1 0 1 1
8 1 0 0 0 1 1 1 1 1 1 1 1 0 1
9 1 0 0 1 1 1 1 1 1 1 1 1 1 0
1 0 1 0 1 1 1 1 1 1 1 1 1 1
1 0 1 1 1 1 1 1 1 1 1 1 1 1
1 1 0 0 1 1 1 1 1 1 1 1 1 1
INVALID

1 1 0 1 1 1 1 1 1 1 1 1 1 1
1 1 1 0 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1

6-70 Electronics Workbench

 74xx

6.4.12474xx43 (Exc-3-to-Decimal Dec)

This excess-3-to-decimal decoder consists of eight inverters and ten four-input NAND gates.
Excess-3-to-decimal decoder truth table

EXCESS-3- INPUT DECIMAL OUTPUT

No. D C B A 0 1 2 3 4 5 6 7 8 9
0 0 0 1 1 0 1 1 1 1 1 1 1 1 1
1 0 1 0 0 1 0 1 1 1 1 1 1 1 1
2 0 1 0 1 1 1 0 1 1 1 1 1 1 1
3 0 1 1 0 1 1 1 0 1 1 1 1 1 1
4 0 1 1 1 1 1 1 1 0 1 1 1 1 1
5 1 0 0 0 1 1 1 1 1 0 1 1 1 1
6 1 0 0 1 1 1 1 1 1 1 0 1 1 1
7 1 0 1 0 1 1 1 1 1 1 1 0 1 1
8 1 0 1 1 1 1 1 1 1 1 1 1 0 1
9 1 1 0 0 1 1 1 1 1 1 1 1 1 0
1 1 0 1 1 1 1 1 1 1 1 1 1 1
1 1 1 0 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1
INVALID

0 0 0 0 1 1 1 1 1 1 1 1 1 1
0 0 0 1 1 1 1 1 1 1 1 1 1 1
0 0 1 0 1 1 1 1 1 1 1 1 1 1

Multisim 8 Component Reference Guide 6-71

TTL

6.4.12574xx44 (Exc-3-Gray-to-Decimal Dec)

This excess-3-gray-to-decimal decoder consists of eight inverters and ten four-input NAND
gates.

Excess-3-gray-to-decimal decoder truth table:

EXCESS-3-GRAY
DECIMAL OUTPUT
INPUT

No. D C B A 0 1 2 3 4 5 6 7 8 9
0 0 0 1 0 0 1 1 1 1 1 1 1 1 1
1 0 1 1 0 1 0 1 1 1 1 1 1 1 1
2 0 1 1 1 1 1 0 1 1 1 1 1 1 1
3 0 1 0 1 1 1 1 0 1 1 1 1 1 1
4 0 1 0 0 1 1 1 1 0 1 1 1 1 1
5 1 1 0 0 1 1 1 1 1 0 1 1 1 1
6 1 1 0 1 1 1 1 1 1 1 0 1 1 1
7 1 1 1 1 1 1 1 1 1 1 1 0 1 1
8 1 1 1 0 1 1 1 1 1 1 1 1 0 1
9 1 0 1 0 1 1 1 1 1 1 1 1 1 0
1 0 1 1 1 1 1 1 1 1 1 1 1 1
1 0 0 1 1 1 1 1 1 1 1 1 1 1
1 0 0 0 1 1 1 1 1 1 1 1 1 1
INVALID

0 0 0 0 1 1 1 1 1 1 1 1 1 1
0 0 0 1 1 1 1 1 1 1 1 1 1 1
0 0 1 1 1 1 1 1 1 1 1 1 1 1

6.4.12674425 (Quad Bus Buffer with 3-State)

This bus buffer has 3-state outputs that, when enabled, have the low impedance characteristics
of a TTL output and additional drive capability at high logic levels to permit driving heavily
loaded bus lines without external pull-up resistors.

6.4.12774426 (Quad Bus Buffer with 3-State)

This bus buffer has 3-state outputs that, when enabled, have the low impedance characteristics
of a TTL output and additional drive capability at high logic levels to permit driving heavily
loaded bus lines without external pull-up resistors.

6-72 Electronics Workbench

 74xx

6.4.12874xx445 (BCD-to-Decimal Dec)

This BCD-to-decimal decoder consists of eight inverters and ten four-input NAND gates.

BCD-to-decimal truth table:

Multisim 8 Component Reference Guide 6-73

TTL

6.4.12974xx45 (BCD-to-Decimal Dec)

This BCD-to-decimal decoder consists of eight inverters and ten four-input NAND gates.

BCD-to-decimal truth table:

6.4.13074xx46 (BCD-to-seven segment dec)

The 7446 BCD (Binary-Coded Decimal)-to-seven-segment decoder translates a 4-bit BCD
input into hexadecimal, and outputs high on the output pins corresponding to the hexadecimal
representation of the BCD input. There are provisions for lamp testing and for blanking the
outputs.

6-74 Electronics Workbench

 74xx

BCD-to-seven-segment decoder:

INPUTS OUTPUTS

BI/
No. LT RBI D C B A a b c d e f g
RBO
0 1 1 0 0 0 0 1 1 1 1 1 1 1 0
1 1 X 0 0 0 1 1 0 1 1 0 0 0 0
2 1 X 0 0 1 0 1 1 1 0 1 1 0 1
3 1 X 0 0 1 1 1 1 1 1 1 0 0 1
4 1 X 0 1 0 0 1 0 1 1 0 0 1 1
5 1 X 0 1 0 1 1 1 0 1 1 0 1 1
6 1 X 0 1 1 0 1 0 0 1 1 1 1 0
7 1 X 0 1 1 1 1 1 1 1 0 0 0 0
8 1 X 1 0 0 0 1 1 1 1 1 1 1 1
9 1 X 1 0 0 1 1 1 1 1 0 0 1 1
10 1 X 1 0 1 0 1 0 0 0 1 1 0 1 I
11 1 X 1 0 1 1 1 0 0 1 1 0 0 1 < N
12 1 X 1 1 0 0 1 0 1 0 0 0 1 1 V
13 1 X 1 1 0 1 1 1 0 0 1 0 1 1 < A
14 1 X 1 1 1 0 1 0 0 0 1 1 1 1 L
I
15 1 X 1 1 1 1 1 0 0 0 0 0 0 0
D
BI X X X X X X 0 0 0 0 0 0 0 0
RBI 1 0 0 0 0 0 0 0 0 0 0 0 0 0
LT 0 X X X X X 1 1 1 1 1 1 1 1

Multisim 8 Component Reference Guide 6-75

TTL

6.4.13174xx465 (Octal BUFFER w/3-state Out)

This device has a two-input active-low AND enable gate controlling all eight data buffers.
Octal buffers truth table:
G1 G2 A Y
0 0 0 0
0 0 1 1
1 0 X Z
0 1 X Z
1 1 X Z

Z = High impedance (off)

6.4.13274xx466 (Octal BUFFER w/3-state Out)

This device has a two-input active-low AND enable gate controlling all eight data buffers.
Octal buffers truth table:

G1 G2 A Y
0 0 0 1
0 0 1 0
1 0 X Z
0 1 X Z
1 1 X Z

Z = High impedance (off)

6.4.13374xx47 (BCD-to-seven segment dec)

The 7447 BCD (Binary-Coded Decimal)-to-seven-segment decoder translates a 4-bit BCD
input into hexadecimal, and outputs high on the output pins corresponding to the hexadecimal
representation of the BCD input. There are provisions for lamp testing and for blanking the
outputs.

6-76 Electronics Workbench

 74xx

BCD-to-seven-segment decoder truth table:

INPUTS OUTPUTS

BI/
No. LT RBI D C B A a b c d e f g
RBO
0 1 1 0 0 0 0 1 1 1 1 1 1 1 0
1 1 X 0 0 0 1 1 0 1 1 0 0 0 0
2 1 X 0 0 1 0 1 1 1 0 1 1 0 1
3 1 X 0 0 1 1 1 1 1 1 1 0 0 1
4 1 X 0 1 0 0 1 0 1 1 0 0 1 1
5 1 X 0 1 0 1 1 1 0 1 1 0 1 1
6 1 X 0 1 1 0 1 0 0 1 1 1 1 0
7 1 X 0 1 1 1 1 1 1 1 0 0 0 0
8 1 X 1 0 0 0 1 1 1 1 1 1 1 1
9 1 X 1 0 0 1 1 1 1 1 0 0 1 1
10 1 X 1 0 1 0 1 0 0 0 1 1 0 1 I
11 1 X 1 0 1 1 1 0 0 1 1 0 0 1 < N
12 1 X 1 1 0 0 1 0 1 0 0 0 1 1 < V
13 1 X 1 1 0 1 1 1 0 0 1 0 1 1 < A
L
14 1 X 1 1 1 0 1 0 0 0 1 1 1 1
I
15 1 X 1 1 1 1 1 0 0 0 0 0 0 0
D
BI X X X X X X 0 0 0 0 0 0 0 0
RBI 1 0 0 0 0 0 0 0 0 0 0 0 0 0
LT 0 X X X X X 1 1 1 1 1 1 1 1

BI = active-low blanking input

RBI = active-low ripple-blanking input
LT = active-low lamp-test input
Notes:
1. The blanking input (BI) must be open or held at a high logic level when output
functions 0 through 15 are desired. The ripple-blanking input (RBI) must be open or
high if blanking of a decimal zero is not desired.
2. When a low logic level is applied to the blanking input (BI), all segment outputs are
low regardless of any other input level.
3. To place the device in lamp-test mode, RBO must be high when LT is low. This forces
all lamps on.

Multisim 8 Component Reference Guide 6-77

TTL

6.4.13474xx48 (BCD-to-seven segment dec)

This device features active-high outputs for driving lamp buffers or common-cathode VLEDs.
It also has full ripple-blanking input/output controls and a lamp test input.
BCD-to-seven-segment decoder:

INPUTS OUTPUTS

BI/
No. LT RBI D C B A a b c d e f g
RBO
0 1 1 0 0 0 0 1 1 1 1 1 1 1 0
1 1 X 0 0 0 1 1 0 1 1 0 0 0 0
2 1 X 0 0 1 0 1 1 1 0 1 1 0 1
3 1 X 0 0 1 1 1 1 1 1 1 0 0 1
4 1 X 0 1 0 0 1 0 1 1 0 0 1 1
5 1 X 0 1 0 1 1 1 0 1 1 0 1 1
6 1 X 0 1 1 0 1 0 0 1 1 1 1 0
7 1 X 0 1 1 1 1 1 1 1 0 0 0 0
8 1 X 1 0 0 0 1 1 1 1 1 1 1 1
9 1 X 1 0 0 1 1 1 1 1 0 0 1 1
10 1 X 1 0 1 0 1 0 0 0 1 1 0 1 INVA
11 1 X 1 0 1 1 1 0 0 1 1 0 0 1 < LID
12 1 X 1 1 0 0 1 0 1 0 0 0 1 1 <
13 1 X 1 1 0 1 1 1 0 0 1 0 1 1 <
14 1 X 1 1 1 0 1 0 0 0 1 1 1 1
15 1 X 1 1 1 1 1 0 0 0 0 0 0 0
BI X X X X X X 0 0 0 0 0 0 0 0
RBI 1 0 0 0 0 0 0 0 0 0 0 0 0 0
LT 0 X X X X X 1 1 1 1 1 1 1 1

6-78 Electronics Workbench

 74xx

BI = active-low blanking input

RBI = active-low ripple-blanking input
LT = active-low lamp-test input
Notes:
1. The blanking input (BI) must be open or held at a high logic level when output
functions 0 through 15 are desired. The ripple-blanking input (RBI) must be open
or high if blanking of a decimal zero is not desired.
2. When a low logic level is applied to the blanking input (BI), all segment outputs
are low regardless of any other input level.
3. To place the device in lamp-test mode, RBO must be high when LT is low. This
forces all lamps on.

6.4.13574xx51 (AND-OR-INVERTER)
AND-OR INVERTER gate truth table:

A B C D Y
0 X X 0 1
X 0 0 X 1
0 X 0 X 1
X 0 X 0 1
1 1 X X 0
X X 1 1 0

Multisim 8 Component Reference Guide 6-79

TTL

6.4.13674xx521 (8-Bit Identity Comparitor)

The 74F521 is an expandable 8-bit comparator. It compares two words of up to eight bits each
and provides a LOW output when the two words match bit for bit. The expansion input IA=B
also serves as an active LOW enable input.

6.4.13774xx533 (Octal D-Latch with inverted O/Ps)

6-80 Electronics Workbench

 74xx

6.4.13874xx534 (Octal Flip-Flop with inverted Latches)

6.4.13974xx54 (4-wide AND-OR-INVERTER)

4-wide AND-OR-INVERTER truth table:

INPUTS OUTPUT

A B C D E F G H Y
1 1 X X X X X X 0
X X 1 1 X X X X 0
X X X X 1 1 X X 0
X X X X X X 1 1 0
X X X X X X X X 1

Multisim 8 Component Reference Guide 6-81

TTL

6.4.14074xx55 (2-wide 4-In AND-OR-INVERTER)

AND-OR-INVERTER truth table:

INPUTS OUTPUT

A B C D E F G H Y
1 1 1 1 1 1 1 1 0
1 1 1 1 X X X X 0
X X X X 1 1 1 1 0
X X X X X X X X 1

6.4.14174xx573 (Octal D-type Latch)

This device contains eight D-type latches with 3-state output buffers. When the Latch Enable
(LE) input is HIGH, data on the Dn inputs enters the latches. In this condition the latches are
transparent, i.e., a latch output will change state each time its D input changes. When LE is
LOW the latches store the information that was present on the D inputs a setup time preceding
the HIGH-to-LOW transition of LE. The 3-state buffers are controlled by the Output Enable
(OE) input. When OE is LOW, the buffers are in the bi-state mode. When OE is HIGH the
buffers are in the high impedance mode but this does not interfere with entering new data into
the latches.

6-82 Electronics Workbench

 74xx

6.4.14274xx574 (Octal D-type Flip-Flop)

This device consists of eight edge-triggered flip-flops with individual D-type inputs and 3-
STATE true outputs. The buffered clock and buffered Output Enable are common to all flip-
flops. The eight flip-flops will store the state of their individual D inputs that meet the setup
and hold times requirements on the LOW-to-HIGH Clock (CP) transition. With the Output
Enable (OE) LOW, the contents of the eight flip-flops are available at the outputs. When OE
is HIGH, the outputs go to the high impedance state. Operation of the OE input does not affect
the state of the flipflops.

6.4.14374xx640 (Octal Bus Transceiver)

The output enable (OE) is active LOW. If the device is disabled (OE HIGH), the outputs are in
the high impedance state. The transmit/receive input (T/R) controls whether data is
transmitted from the A bus to the B bus or from the B bus to the A bus. When T/R is LOW, B
data is sent to the A bus. If T/R is HIGH, A data is sent to the B bus.

Multisim 8 Component Reference Guide 6-83

TTL

6.4.14474xx645 (Octal Bus Transceiver)

The output enable (OE) is active LOW. If the device is disabled (OE HIGH), the outputs are in
the high impedance state. The transmit/receive input (T/R) controls whether data is
transmitted from the A bus to the B bus or from the B bus to the A bus. When T/R is LOW, B
data is sent to the A bus. If T/R is HIGH, A data is sent to the B bus.

6.4.14574xx69 (Dual 4-bit Binary Counter)

Counter number one has two sections - counter A (divide-by-2 section) and counter B, C, D
(divide-by-8 section). Counter number two has only divide-by-sixteen section.
4-Bit counter truth table:

1CLR 2CLR 1QA 1QB 1QC 1QD 2QA 2QB 2QC 2QD
1 1 COUNT COUNT
1 0 COUNT 0 0 0 0
0 1 0 0 0 0 COUNT
0 0 0 0 0 0 0 0 0 0

6.4.14674xx72 (AND-gated JK MS-SLV FF (pre, clr))

This device is equipped with an active-low pre and active-low clr. Therefore, the flip-flop
begins accepting input from the JK input when the preset and clear are both high (hence
AND-gated).

6-84 Electronics Workbench

 74xx

AND-gated JK flip-flop truth table:

PRE CLR CLK J K Q Q

0 1 X X X 1 0
1 0 X X X 0 1
0 0 X X X UNSTABLE
1 1 · 0 0 Q0 Q0
1 1 · 1 0 1 0
1 1 · 0 1 0 1
1 1 · 1 1 Toggle

· = triggers on pulse (level sensitive)

6.4.14774xx73 (Dual JK FF (clr))

This device contains 2-independent JK flip-flops.
JK flip-flop truth table:

CLR CLK J K Q Q
0 X X X 0 1
1 · 0 0 Hold
1 · 1 0 1 0
1 · 0 1 0 1
1 · 1 1 Toggle

· = triggers on pulse (level sensitive)

6.4.14874xx74 (Dual D-type FF (pre, clr))

This device is equipped with active-low preset and active-low clear inputs.

Multisim 8 Component Reference Guide 6-85

TTL

D-type positive-edge-triggered flip-flop truth table:

PRE CLR CLK D Q Q

0 1 X X 1 0
1 0 X X 0 1
0 0 X X 1 1
1 1 · 1 1 0
1 1 · 0 0 1
1 1 0 X Hold

· = positive edge-triggered

6.4.14974xx75 (4-bit Bistable Latches)

This device features complementary Q and Q outputs from a 4-bit latch.
Bistable latch truth table:

INPUTS OUTPUTS

D C Q Q
0 1 0 1
1 1 1 0
X 0 Q0 Q0

6.4.15074xx76 (Dual JK FF (pre, clr))

This device contains two independent J-K flip-flops with individual J-K, clock, preset, and
clear inputs.

6-86 Electronics Workbench

 74xx

JK flip-flop truth table:

PRE CLR CLK J K Q Q

0 1 X X X 1 0
1 0 X X X 0 1
0 0 X X X 1 1
1 1 · 0 0 Hold
1 1 · 1 0 1 0
1 1 · 0 1 0 1
1 1 · 1 1 Toggle

· = pulse triggered (level sensitive)

6.4.15174xx77 (4-bit Bistable Latches)

This 4-bit latch is available in a 14-pin flat package.
Bistable latch truth table:

D C L H
0 1 1 0
1 1 1 0
X 0 Hold

6.4.15274xx78 (Dual JK FF (pre, com clk & clr))

The 7478 contains two negative-edge triggered flip-flops with individual JK, individual
preset, common clock and common clear inputs.

Multisim 8 Component Reference Guide 6-87

TTL

JK flip-flop truth table:

PRESET CLEAR J K CLOCK Q Q

0 1 X X X 1 0
1 0 X X X 0 1
0 0 X X X 1* 1* (unstable)
1 1 0 0 Ø (no change)
1 1 0 1 Ø 0 1
1 1 1 0 Ø 1 0
1 1 1 1 Ø (toggle)
1 1 X X 1 (no change)

* = This configuration will not persist when preset and clear are inactive.
Ø = Transition from high to low.

6-88 Electronics Workbench

 74xx

6.4.15374xx82 (2-bit Bin Full Adder)

This device performs the addition of two 2-bit binary numbers.
2-bit binary full adder truth table:

INPUTS OUTPUTS

WHEN CO = L WHEN CO = H

A1 B1 A2 B2 S1 S2 C2 S1 S2 C2
0 0 0 0 0 0 0 1 0 0
1 0 0 0 1 0 0 0 1 0
0 1 0 0 1 0 0 0 1 0
1 1 0 0 0 1 0 1 1 0
0 0 1 0 0 1 0 1 1 0
1 0 1 0 1 1 0 0 0 1
0 1 1 0 1 1 0 0 0 1
1 1 1 0 0 0 1 1 0 1
0 0 0 1 0 1 0 1 1 0
1 0 0 1 1 1 0 0 0 1
0 1 0 1 1 1 0 0 0 1
1 1 0 1 0 0 1 1 0 1
0 0 1 1 0 0 1 1 0 1
1 0 1 1 1 0 1 0 1 1
0 1 1 1 1 0 1 0 1 1
1 1 1 1 0 1 1 1 1 1

6.4.15474xx821 (10-Bit D-type Flip-Flop)

This device consists of ten D-type edge-triggered flipflops. This device has 3-STATE true
outputs for bus systems organized in a broadside pinning. The buffered Clock (CP) and
buffered Output Enable (OE) are common to all flip-flops. The flip-flops will store the state of
their individual D inputs that meet the setup and hold times requirements on the LOW-to-
HIGH CP transition. With the OE LOW the content of the flip-flops are available at the

Multisim 8 Component Reference Guide 6-89

TTL

outputs. When the OE is HIGH, the outputs go to the high impedance state. Operation of the
OE input does not affect the state of the flip-flops.

6.4.15574xx823 (9-Bit D-type Flip-Flop)

This device consists of nine D-type edge-triggered flip-flops. It has 3-STATE true outputs and
is organized in broadside pinning. The buffered Clock (CP) and buffered Output Enable (OE)
are common to all flip-flops. The flip-flops will store the state of their individual D inputs that
meet the setup and hold times requirements on the LOW-to-HIGH CP transition. With the OE
LOW the contents of the flip-flops are available at the outputs. When the OE is HIGH, the
outputs go to the high impedance state. Operation of the OE input does not affect the state of
the flip-flops. In addition to the Clock and Output Enable pins, the 74F823 has Clear (CLR)
and Clock Enable (EN) pins. When the CLR is LOW and the OE is LOW, the outputs are
LOW. When CLR is HIGH, data can be entered into the flip-flops. When EN is LOW, data on
the inputs is transferred to the outputs on the LOW-to-HIGH clock transition. When the EN is

6-90 Electronics Workbench

 74xx

HIGH, the outputs do not change state regardless of the data or clock inputs transitions. This
device is ideal for parity bus interfacing in high performance systems.

6.4.15674xx825 (8-Bit D-Type Flip-Flop)

This device consists of eight D-type edge-triggered flip-flops. This device has 3-STATE true
outputs and is organized in broadside pinning. In addition to the clock and output enable pins,
the buffered clock (CP) and buffered Output Enable (OE) are common to all flip-flops. The
flip-flops will store the state of their individual D inputs that meet the setup and hold times
requirements on the LOW-to-HIGH CP transition. With the OE LOW the contents of the flip-
flops are available at the outputs. When the OE is HIGH, the outputs go to the high impedance
state. Operation of the OE input does not affect the state of the flip-flops. The 74F825 has
Clear (CLR) and Clock Enable (EN) pins. When the CLR is LOW and the OE is LOW the
outputs are LOW. When CLR is HIGH, data can be entered into the flip-flops. When EN is
LOW, data on the inputs is transferred to the outputs on the LOW-to-HIGH clock transition.

Multisim 8 Component Reference Guide 6-91

TTL

When the EN is HIGH the outputs do not change state, regardless of the data or clock input
transitions.

6.4.15774xx827 (10-Bit Buffers/Line Drivers)

This device is a line driver designed to be employed as memory address drivers, clock drivers
and bus-oriented transmitters/receivers which provide improved PC board density. The
devices have 3-STATE outputs controlled by the Output Enable (OE) pins. The outputs can
sink 64 mA and source 15 mA. Input clamp diodes limit high-speed termination effects.

6-92 Electronics Workbench

 74xx

6.4.15874xx828 (10-Bit Buffers/Line Drivers)

This device is a line driver designed to be employed as memory address drivers, clock drivers
and bus-oriented transmitters/receivers which provide improved PC board density. The
devices have 3-STATE outputs controlled by the Output Enable (OE) pins. The outputs can
sink 64 mA and source 15 mA. Input clamp diodes limit high-speed termination effects.

6.4.15974xx83 (4-bit Bin Full Adder)

This device performs the addition of two 4-bit binary numbers. It features full internal look-
ahead across all four bits generating the carry term in ten nanoseconds typically.

Multisim 8 Component Reference Guide 6-93

TTL

6.4.16074xx85 (4-bit Mag COMP)

This 4-bit magnitude comparator performs comparison of straight binary and straight BCD
(8-4-2-1) codes.
4-bit magnitude comparator truth table:

COMPARING CASCADING
OUTPUTS
INPUTS INPUTS

A3, B3 A2, B2 A1, B1 A0, B0 A>B A<B A=B A>B A<B A=B
A3>B3 X X X X X X 1 0 0
A3<B3 X X X X X X 0 1 0
A3=B3 A2>B2 X X X X X 1 0 0
A3=B3 A2<B2 X X X X X 0 1 0
A3=B3 A2=B2 A1>B1 X X X X 1 0 0
A3=B3 A2=B2 A1<B1 X X X X 0 1 0
A3=B3 A2=B2 A1=B1 A0>B0 X X X 1 0 0
A3=B3 A2=B2 A1=B1 A0<B0 X X X 0 1 0
A3=B3 A2=B2 A1=B1 A0=B0 1 0 0 1 0 0
A3=B3 A2=B2 A1=B1 A0=B0 0 1 0 0 1 0
A3=B3 A2=B2 A1=B1 A0=B0 0 0 1 0 0 1
A3=B3 A2=B2 A1=B1 A0=B0 X X 1 0 0 1
A3=B3 A2=B2 A1=B1 A0=B0 1 1 0 0 0 0
A3=B3 A2=B2 A1=B1 A0=B0 0 0 0 1 1 0
A3=B3 A2=B2 A1=B1 A0=B0 0 1 1 0 1 1
A3=B3 A2=B2 A1=B1 A0=B0 1 0 1 1 0 1
A3=B3 A2=B2 A1=B1 A0=B0 1 1 1 1 1 1
A3=B3 A2=B2 A1=B1 A0=B0 1 1 0 1 1 0
A3=B3 A2=B2 A1=B1 A0=B0 0 0 0 0 0 0

6.4.16174xx86 (Quad 2-In XOR)

Logic function:
Y = A⊕B

6-94 Electronics Workbench

 74xx

EXCLUSIVE-OR gate truth table:

A B Y
0 0 0
0 1 1
1 0 1
1 1 0

6.4.16274xx90 (Decade Counter)

The 7490 counts from 0 to 9 in binary. It contains four master-slave flip-flops and additional
gating to provide a divide-by-two counter and a three-stage binary counter for which the
count cycle length is divide-by-five.
Decade counter truth table:

RESET INPUTS OUTPUT

R0(1) R0(2) R9(1) R9(2) Qd Qc Qb Qa

1 1 0 X 0 0 0 0
1 1 X 0 0 0 0 0
X X 1 1 1 0 0 1
X 0 X 0 COUNT
0 X 0 X COUNT
0 X X 0 COUNT
X 0 0 X COUNT

6.4.16374xx91 (8-bit Shift Reg)

This 8-bit shift register contains eight R-S master-slave flip-flops, input gating, and a clock
driver.

Multisim 8 Component Reference Guide 6-95

TTL

Shift register truth table:

A B Qh Qh
1 1 1 0
0 X 0 1
X 0 0 1

PRESET PRESET SERIAL OUTPUTS

CLR ENABLE A B C D CLK QA QB QC QD QE

0 0 X X X X X X 0 0 0 0 0
0 X 0 0 0 0 X X 0 0 0 0 0
1 1 1 1 1 1 X X 1 1 1 1 1
1 1 0 0 0 0 0 X QA0 QB0 QC0 QD0 QE0
1 1 1 0 1 0 0 X 1 QB0 1 QD0 1
1 0 X X X X 0 X QA0 QB0 QC0 QD0 QE0
1 0 X X X X · 1 1 QAn QBn QCn QDn
1 0 X X X X · 0 0 QAn QBn QCn QDn

· = transition from low to high level

QA0, QB0, etc. = the level of QA, QB, etc. respectively before the indicated steady state
input conditions were established
QAn, QBn, etc. = the level of QA, QB, etc. respectively before the most recent negative
transition of the clock

6.4.16474xx92 (Divide-by-twelve Counter)

The 7492 counts from 0 to 11 in binary. It contains four master-slave flip-flops and additional
gating to provide a divide-by-two counter and a three-stage binary counter for which the
count cycle length is divide-by-six.
Counter truth table:

RESET INPUTS OUTPUT

RO1 RO2 Qd Qc Qb Qa
1 1 0 0 0 0
0 X Count
X 0 Count

6-96 Electronics Workbench

 74xx

6.4.16574xx93 (4-bit Binary Counter)

The 7493 counts from 0 to 15 in binary. It contains four master-slave flip-flops and additional
gating to provide a divide-by-two counter and a three-stage binary counter for which the
count cycle length is divide-by-eight.
Binary counter truth table:

RESET INPUTS OUTPUT

RO1 RO2 Qd Qc Qb Qa
1 1 0 0 0 0
0 X Count
X 0 Count

Multisim 8 Component Reference Guide 6-97

TTL

6-98 Electronics Workbench

Chapter 7
CMOS

7.1 CMOS Overview

The complementary MOS (CMOS) logic family uses both P- and N-channel MOSFETS in
the same circuit. CMOS is faster and consumes less power than the other MOS families.
CMOS ICs provide not only all of the same logic functions available in TTL, but also several
special functions not provided by TTL.
The 74C series is pin-compatible (pin configuration of the two ICs are the same) with and
functionally equivalent to TTL devices with the same number. Many but not all functions that
are available in TTL are also available in the 74C series. It is possible then to replace some
TTL circuits with an equivalent design.
The 74HC/HCT series is an improved version of the 74C series. It has a tenfold increase in
switching speed compared to the 74LS devies and a higher output curre t capability than that
of the 74C. The 74HC?HCT ICs are pin-compatible with and functionally equivalent to TTL
ICs with the same number. 74HCT devices are electrically compatible with TTL, but devices
from the 74C series are not.
The 74AC/ACT series, often referred to as ACL, for advanced CMOS logic, is functionally
equivalent to the various TTL series, but is not pin-compatible with TTL. 74AC devices are
not electrically compatible with TTL; however, the 74ACT devices can be connected directly
to TTL. The 74AC/ACT series has advantages over the HC series in the areas of noise
immunity, propagation delay, and maximum clock speed. The device numbering for this
series differs from TTL, 74C and 74HC/HCT numbering.
The 74AHC is the newest series of CMOS devices. The devices in this series are three times
faster than and can replace the HC series devices.

Multisim 8 Component Reference Guide 7-1

CMOS

7.1.1 Power-Supply Voltage

The 4000/14000 series and 74C series devices can operate with VDD values ranging from 3 to
15 V. The 74HC/HCT and 74AC/ACT series operate over a range of supply voltages between
2 and 6 V.

7.1.2 Logic Voltage Levels

The input and ouput voltage levels are different for each CMOS series. The VOL for the
CMOS devices is close to 0 V and the VON is close to 5 V. The required input voltage levels
are greater for CMOS than for TTL, except for the 74 ACT series. These series are designed
to be electrically comparable with TTL, so they must accept the same input voltage levels as
TTL.

7.1.3 Noise Margins

The CMOS devices have greater noise margins than TTL.

7.1.4 Power Dissipation

The power dissipation of a CMOS logic circuit is very low when the circuit is in a static state.
The pwoer dissipation of a CMOS IC increases in proportion to the frequency at which the
circuits are switching states.

7.2 4000 Series ICs

The 4000 component in the parts bin is a generic IC, or template. It has no pins or labels and
cannot be wired into a circuit.
To use an IC, drag the template onto the circuit window. A list of available ICs for this family
appears. Select the IC you want to include in your circuit. The correct graphic will appear
containing labels and pins.

7-2 Electronics Workbench

 4000 Series ICs

7.2.1 4000 (Dual 3-In NOR and INVERTER)

Logic function:

O1 = I1+I2+I3
O2 = I4+I5+I6
O3 = I7

NOR gate truth table:

I1 I2 I3 O1
0 0 0 1
1 0 0 0
0 1 0 0
1 1 0 0
0 0 1 0
1 0 1 0
0 1 1 0
1 1 1 0

7.2.2 4001 (Quad 2-In NOR)

This device contains four independent 2-input NOR gates.

Logic function:
O1 = I1+I2

Multisim 8 Component Reference Guide 7-3

CMOS

NOR gate truth table:

I1 I2 O1
0 0 1
1 0 0
0 1 0
1 1 0

7.2.3 4002 (Dual 4-In NOR)

This device contains four independent 4-input NOR gates.

Logic function:
O1 = I1+I2+I3+I4
O2 = I5+I6+I7+I8

NOR gate truth table:

I1 I2 I3 I4 O1
1 X X X 0
X 1 X X 0
X X 1 X 0
X X X 1 0
0 0 0 0 1

7.2.4 4007 (Dual Com Pair/Inv)

This device is a dual complementary pair and an inverter with access to each device. It has
three n-channel and three p-channel enhancement mode MOS transistors.

7-4 Electronics Workbench

 4000 Series ICs

7.2.5 4008 (4-bit Binary Full Adder)

This device is capable of adding two 4-bit binary numbers together.

Logic function:

S = CIN ⊕ A ⊕ B
C = AB+BCOUT+ACOUT

4-bit binary adder truth table:

INPUTS OUTPUTS
CIN A1 B1 A2 B2 A3 B3 A4 B4 COUT
X 1 X X 1 X 1 X 1 1
X X X 1 X X 1 X 1 1
X X X X X 1 X X 1 1
X X X X X X X 1 X 1
1 X 1 X 1 X 1 X 1 1
X X X X X X X X X 0

Multisim 8 Component Reference Guide 7-5

CMOS

7.2.6 4010 (Hex BUFFER)

This device contains six independent BUFFER gates.

Logic function:
Y = A

BUFFER gate truth table:

A Y
0 0
1 1

7.2.7 40106 (Hex INVERTER (Schmitt))

This device contains six independent INVERTER gates. Due the to the Schmitt-trigger action,
this device is ideal for circuits that are susceptible to unwanted small signals, such as noise.
Logic function:
Y = A

INVERTER gate truth table:

A Y
0 1
1 0

7-6 Electronics Workbench

 4000 Series ICs

7.2.8 4011 (Quad 2-In NAND)

This device contains four independent 2-input NAND gates.

Logic function:
O1 = I1 I2

NAND gate truth table:

I1 I2 O1
0 0 1
1 0 1
0 1 1
1 1 0

7.2.9 4012 (Dual 4-In NAND)

This device contains four independent 4-input NAND gates.

Logic function:

O1 = I1+I2+I3+I4

Multisim 8 Component Reference Guide 7-7

CMOS

NAND gate truth table:

INPUTS OUTPUTS
I1 I2 I3 I4 O1
1 1 1 1 0
0 X X X 1
X 0 X X 1
X X 0 X 1
X X X 0 1

7.2.10 4013 (Dual D-type FF (+edge))

he 4013 device is a dual D-type flip-flop that features independent set direct (SD), clear
irect (CD), clock inputs (CP) and outputs (O,O).

D-type positive edge-triggered flip-flop truth table:

SD CD CP D O O
1 0 X X 1 0
0 1 X X 0 1
1 1 X X 1 1
0 0 · 0 0 1
0 0 · 1 1 0

· = positive edge-triggered

7-8 Electronics Workbench

 4000 Series ICs

7.2.11 4014 (8-bit Static Shift Reg)

The 4014 device is a fully synchronous edge-triggered 8-bit static shift register with eight
synchronous parallel inputs (P0 to P7), a synchronous serial data input (DS), a synchronous
parallel enable input (PE), a LOW to HIGH edge-triggered clock input (CP) and buffered
parallel outputs from the last three stages (O5 to O7).
Following are two 8-bit static shift register truth tables.

Multisim 8 Component Reference Guide 7-9

CMOS

Serial Operation:
INPUTS OUTPUTS
n PE DS >CLK P0 P1 P2 P3 P4 P5 P6 P7 O5 O6 O7
1 0 D1 · X X X X X X X X X X X
2 0 D2 · X X X X X X X X X X X
3 0 D3 · X X X X X X X X X X X
4 0 D4 · X X X X X X X X X X X
5 0 D5 · X X X X X X X X X X X
6 0 D6 · X X X X X X X X D1 X X
7 0 D7 · X X X X X X X X D2 D1 X
9 0 D8 · X X X X X X X X D3 D2 D1
10 0 D9 · X X X X X X X X D4 D3 D2
X X X ‚ X X X X X X X X no change

Parallel Operation:
INPUTS OUTPUTS
PE DS >CLK P0 P1 P2 P3 P4 P5 P6 P7 O5 O6 O7
1 X · X X X X X X X X P5 P6 P7
1 X ‚ X X X X X X X X no change

7.2.12 4015 (Dual 4-bit Static Shift Reg)

The 4015 device is a dual edge-triggered 4-bit static shift register (serial-to-parallel
converter). Each shift register has a serial data input (D), a clock input (CP), four fully
buffered parallel outputs (O0 to O3) and an overriding asynchronous master reset input (MR).

7-10 Electronics Workbench

 4000 Series ICs

Shift register truth table:

n CP D MR O0 O1 O2 O3
1 · D1 0 D1 X X X
2 · D2 0 D2 D1 X X
3 · D3 0 D3 D2 D1 X
4 · D4 0 D4 D3 D2 D1
‚ X 0 no change
X X 1 0 0 0 0

1 = HIGH state (the more positive voltage)

0 = LOW state (the less positive voltage)
X = state is immaterial
· = positive-going transition
‚ = negative-going transition
Dn = either HIGH or LOW
n = number of clock pulse transitions

7.2.13 40160 (4-bit Dec Counter)

Multisim 8 Component Reference Guide 7-11

CMOS

The 40160 device is a fully synchronous edge-triggered 4-bit decade counter with a clock
input (CP), an overriding asynchronous master reset (MR), four parallel data inputs (P0 to
P3), three synchronous mode control inputs (parallel enable (PE), count enable parallel
(CEP) and count enable trickle (CET)), buffered outputs from all four bit positions (O0 to
O3) and a terminal count output (TC).

7.2.14 40161 (4-bit Bin Counter)

The 40161 device is a fully synchronous edge-triggered 4-bit binary counter with a clock
input (CP), an overriding asynchronous master reset (MR), four parallel data inputs (P0 to
P3), three synchronous mode control inputs (parallel enable (PE), count enable parallel
(CEP) and count enable trickle (CET)), buffered outputs from all four bit positions (O0 to
O3) and a terminal count output (TC).

7-12 Electronics Workbench

 4000 Series ICs

7.2.15 40162 (4-bit Dec Counter)

The 40162 device is a fully synchronous edge-triggered 4-bit decade counter with a clock
input (CP), four synchronous parallel data inputs (P0 to P3), four synchronous mode
control inputs (parallel enable (PE), count enable parallel (CEP) and count enable trickle
(CET)), and synchronous reset (SR)), buffered outputs from all four bit positions (O0 to
O3) and a terminal count output (TC).

7.2.16 40163 (4-bit Bin Counter)

The 40163 device is a fully synchronous edge-triggered 4-bit binary counter with a clock
input (CP), four synchronous parallel data inputs (P0 to P3), four synchronous mode
control inputs (parallel enable (PE), count enable parallel (CEP) and count enable trickle
(CET)), and synchronous reset (SR)), buffered outputs from all four bit positions (O0 to
O3) and a terminal count output (TC).

Multisim 8 Component Reference Guide 7-13

CMOS

7.2.17 4017 (5-stage Johnson Counter)

The 4017 device is a 5-stage Johnson decade counter with ten spike-free decoded active
HIGH outputs (O0 to Og), an active LOW output from the most significant flip-flop (O5-9),
active HIGH and active LOW clock inputs (CP0, CP1) and an overriding asynchronous
master reset input (MR).

5-stage Johnson counter truth table:

MR CP0 CP1 OPERATION
1 X X O0 = O5-9 = H; O1 to O9 = L
0 1 ‚ Counter advances
0 · 0 Counter advances
0 0 X No change
0 X 1 No change
0 1 · No change
0 ‚ 0 No change

1 = HIGH state (the more positive voltage)

0 = LOW state (the less positive voltage)
X = state is immaterial
· = positive-going transition
‚ = negative-going transition
n = number of clock pulse transitions

7-14 Electronics Workbench

 4000 Series ICs

7.2.18 40174 (Hex D-type Flip-flop)

The 40174 device is a hex edge-triggered D-type flip-flop with six data inputs (D0 to D5), a
clock input (CP), an overriding asynchronous master reset input (MR), and six buffered
outputs (O0 to O5).

Hex D-type flip-flop truth table:

INPUTS OUTPUT
CP D MR O
1 1 1
0 1 0
X 1 no change
X X 0 0

1 = HIGH state (the more positive voltage)

0 = LOW state (the less positive voltage)
X = state is immaterial
= positive-going transition
= negative-going transition

Multisim 8 Component Reference Guide 7-15

CMOS

7.2.19 40175 (Quad D-type Flip-flop)

This device is a quadruple edge-triggered D-type flip-flop with four data inputs (D0 to D3),
a clock input (CP), an overriding asynchronous master rest input (MR), four buffered
outputs (O0 to O3), and four complementary buffered outputs (O0 to O3).

Quadruple D-type flip-flop truth table:

INPUTS OUTPUTS
CP D MR O O
1 1 1 0
0 1 0 1
X 1 no change no change
X X 0 0 1

1 = HIGH state (the more positive voltage)

0 = LOW state (the less positive voltage)
X = state is immaterial
= positive-going transition
= negative-going transition

7-16 Electronics Workbench

 4000 Series ICs

7.2.20 4018 (5-stage Johnson Counter)

The 4018 device is a 5-stage Johnson counter with a clock input (CP), a data input (D), an
asynchronous parallel load input (PL), five parallel inputs (P0 to P4), five active LOW
buffered outputs (O0 to O4), and an overriding asynchronous master reset input (MR).

5-stage Johnson counter truth table:

Counter mode; Connect D
Remarks
divide by input to
10 O4
8 O3
6 O2 no external compo-
4 O1 nents needed
2 O0
9 O3•O4
7 O2•O3 AND gate needed;
5 O1•O2 counter skips all HIGH
3 00•O1 states

Multisim 8 Component Reference Guide 7-17

CMOS

7.2.21 4019 (Quad 2-In MUX)

The 4019 device provides four multiplexing circuits with common select inputs (SA, SB);
each circuit contains two inputs (An, Bn) and one output (On).

Multiplexer truth table:

SELECT INPUTS OUTPUTS
Sa Sb A0 B0 O0
0 0 X X 0
1 0 0 X 0
1 0 1 X 1
0 1 X 0 0
0 1 X 1 1
1 1 1 X 1
1 1 X 1 1
1 1 0 0 0

7-18 Electronics Workbench

 4000 Series ICs

7.2.22 40192 (4-bit Dec Counter)

The 40192 device is a 4-bit synchronous up/down decade counter with a count-up clock
input (CPU), a count-down clock input (CPD), an asynchronous parallel load input (PL),
four parallel data inputs (P0 to P3), an asynchronous master reset input (MR), four counter
outputs (O0 to O3), an active LOW terminal count-up (carry) output (TCU) and an active
LOW terminal count-down (borrow) output (TCD).

7.2.23 40193 (4-bit Bin Counter)

The 40193 device is a 4-bit synchronous up/down binary counter with a count-up clock
input (CPU), a count-down clock input (CPD), an asynchronous parallel load input (PL),
four parallel data inputs (P0 to P3), an asynchronous master reset input (MR), four counter
outputs (O0 to O3), an active LOW terminal count-up (carry) output (TCU) and an active
LOW terminal count-down (borrow) output (TCD).

Multisim 8 Component Reference Guide 7-19

CMOS

7.2.24 40194 (4-bit Shift Register)

The 40194 device is a 4-bit bidirectional shift register with two mode control inputs (S0 and
S1), a clock input (CP), a serial data shift left input (DSL), a serial data shift right input
(DSR), four parallel data inputs (P0 to P3), an overriding asynchronous master reset input
(MR), and four buffered parallel outputs (O0 to O3).

7.2.25 40195 (4-bit Shift Register)

7-20 Electronics Workbench

 4000 Series ICs

The 40195 device is a fully synchronous edge-triggered 4-bit shift register with a clock
input (CP), four synchronous parallel data inputs (P0 to P3), two synchronous serial data
inputs (J, K), a synchronous parallel enable input (PE), buffered parallel outputs from all 4-
bit positions (O0 to O3), a buffered inverted output from the last bit position (O3) and an
overriding asynchronous master reset input (MR).

7.2.26 4020 (14-stage Bin Counter)

The 4020 device is a 14-stage binary ripple counter with a clock input (CP), an overriding
asynchronous master reset input (MR) and twelve fully buffered outputs (O0, O3 to O13).

7.2.27 4021 (8-bit Static Shift Register)

Multisim 8 Component Reference Guide 7-21

CMOS

The 4021 device is an 8-bit static shift register (parallel-to-serial converter) with a
synchronous serial data input (DS), a clock input (CP), an asynchronous active HIGH parallel
load input (PL), eight asynchronous parallel data inputs (P0 to P7) and buffered parallel
outputs from the last three stages (O5 to O7).

7.2.28 4023 (Tri 3-In NAND)

This device contains three independent 3-input NAND gates.

Logic function:
O = I1+I2+I3

NAND gate truth table:

I1 I2 I3 O1
0 0 0 1
1 0 0 1
0 1 0 1
1 1 0 1
0 0 1 1
1 0 1 1
0 1 1 1
1 1 1 0

7-22 Electronics Workbench

 4000 Series ICs

7.2.29 4024 (7-stage Binary Counter)

The 4024 is a 7-stage binary ripple counter. A high on MR (Master Reset) forces all counter
stages and outputs low.
The 4024 counts from 0 to 15 in binary on every negative (high to low) transition of the clock
pulse

7-stage counter truth table:

INPUTS OUTPUTS
MR CP Qg Qf Qe Qd Qc Qb Qa
1 X 0 0 0 0 0 0 0
0 ‚ Count
0 ‚ Count

7.2.30 40240 (Octal Inv Buffer)

The 40240 device is an octal inverting buffer with 3-state outputs.

Multisim 8 Component Reference Guide 7-23

CMOS

7.2.31 40244 (Octal Non-inv Buffer)

The 40244 device is an octal non-inverting buffer with 3-state outputs.

7.2.32 40245 (Octal Bus Transceiver)

The 40245 device, an octal bus transmitter/receiver with 3-state outputs, is designed for 8-line
asynchronous, 2-way data communication between data buses.

7.2.33 4025 (Tri 3-In NOR)

This device contains three independent 3-input NOR gates.

7-24 Electronics Workbench

 4000 Series ICs

Logic function:
O = I1+I2+I3

NOR gate truth table:

I1 I2 I3 O1
0 0 0 1
0 1 0 0
1 0 0 0
1 1 0 0
0 0 1 0
1 0 1 0
0 1 1 0
1 1 1 0

7.2.34 4027 (Dual JK FF (+edge, pre, clr))

This device contains two independent JK flip-flops. They have separate preset and clear
inputs.

Multisim 8 Component Reference Guide 7-25

CMOS

JK flip-flop truth table:

SD CD CP J K On On
1 0 X X X 1 0
0 1 X X X 0 1
1 1 X X X 1 1
0 0 · 0 0 Hold
0 0 · 1 0 1 0
0 0 · 0 1 0 1
0 0 · 1 1 Toggle

· = triggers on POSITIVE pulse

7.2.35 4028 (1-of-10 Dec)

The 4028 device is a 4-bit BCD to 1-of-10 active HIGH decoder.

7-26 Electronics Workbench

 4000 Series ICs

1-of-10 decoder truth table:

BCD INPUTS DECIMAL OUTPUTS
A3 A2 A1 A0 O0 O1 O2 O3 O4 O5 O6 O7 O8 O9
0 0 0 0 1 0 0 0 0 0 0 0 0 0
0 0 0 1 0 1 0 0 0 0 0 0 0 0
0 0 1 0 0 0 1 0 0 0 0 0 0 0
0 0 1 1 0 0 0 1 0 0 0 0 0 0
0 1 0 0 0 0 0 0 1 0 0 0 0 0
0 1 0 1 0 0 0 0 0 1 0 0 1 0
0 1 1 0 0 0 0 0 0 0 1 0 0 0
0 1 1 1 0 0 0 0 0 0 0 1 0 0
1 0 0 0 0 0 0 0 0 0 0 0 1 0
1 0 0 1 0 0 0 0 0 0 0 0 0 1
*Extraordinary states
1 0 1 0 0 0 0 0 0 0 0 0 0 0
1 0 1 1 0 0 0 0 0 0 0 0 0 0
1 1 0 0 0 0 0 0 0 0 0 0 0 0
1 1 0 1 0 0 0 0 0 0 0 0 0 0
1 1 1 0 0 0 0 0 0 0 0 0 0 0
1 1 1 1 0 0 0 0 0 0 0 0 0 0

7.2.36 4029 (4-bit Bin/BCD Dec Counter)

Multisim 8 Component Reference Guide 7-27

CMOS

The 4029 is a synchronous edge-triggered up/down 4-bit binary/BCD decade counter with a
clock input (CP), an active LOW count enable input (CE), an up/down control input (UP/
DN), a binary/decade control input (BIN/DEC), an overriding asynchronous active HIGH
parallel load input (PL), four parallel data inputs (P0 to P3), four parallel buffered outputs
(O0 to O3) and an active LOW terminal count output (TC).

4-bit binary/BCD decade counter truth table:

PL BIN/DEC UP/DN CE CP mode
1 X X X X parallel load (Pn
On)
0 X X 1 X no change
0 0 0 0 count-down, decade
0 0 1 0 count-up, decade
0 1 0 0 count-down, binary
0 1 1 0 count-up, binary

1 = HIGH state (the more positive voltage)

0 = LOW state (the less positive voltage)
X = state is immaterial
= positive-going clock pulse edge

7.2.37 4030 (Quad 2-In XOR)

This device contains four independent 2-input EXCLUSIVE-OR gates.

Logic function:
O = I1 ⊕ I2

7-28 Electronics Workbench

 4000 Series ICs

EXCLUSIVE-OR gate truth table:

I1 I2 O1
0 0 0
0 1 1
1 0 1
1 1 0

7.2.38 4032 (Triple Serial Adder)

The 4032 triple serial adder has the clock and carry reset inputs common to all three adders.
The carry is added on the positive-going clock transition for this device.

7.2.39 4035 (4-bit Shift Register)

Multisim 8 Component Reference Guide 7-29

CMOS

The 4035 device is a fully synchronous edge-triggered 4-bit shift register with a clock input
(CP), four synchronous parallel data inputs (P0 to P3), two synchronous serial data inputs
(J, K), a synchronous parallel enable input (PE), buffered parallel outputs from all 4-bit
positions (O0 to O3), a true/complement input (T/C) and an overriding asynchronous
master reset input (MR).
Following are two shift register truth tables.

Serial operation first stage:

INPUTS OUTPUT
CP J K MR O0+1 MODE OF OPERATION
1 1 0 1 D flip-flop
0 0 0 0 D flip-flop
1 0 0 O0 toggle
0 1 0 O0 no change
X X X 1 0 reset

7-30 Electronics Workbench

 4000 Series ICs

Parallel operation:
INPUTS OUTPUTS
CP
P0 P1 P2 P3 O0 O1 O2 O3
0 0 0 0 0 0 0 0
1 1 1 1 1 1 1 1

= positive-going transition
1 = HIGH state (the more positive voltage)
0 = LOW state (the less positive voltage)
X = state is immaterial

7.2.40 40373 (Octal Trans Latch)

The 40373 device is an 8-bit transparent latch with 3-state buffered outputs.

Multisim 8 Component Reference Guide 7-31

CMOS

7.2.41 40374 (Octal D-type Flip-flop)

The 40374 device is an octal D-type flip-flop with 3-state buffered outputs with a common
clock input (CP). It used primarily as an 8-bit positive edge-triggered storage register for
interfacing with a 3-state bus.

7.2.42 4038 (Triple Serial Adder)

The 4038 triple serial adder has the clock and carry reset inputs common to all three adders.
The carry is added on the negative-going clock transition for this device.

7-32 Electronics Workbench

 4000 Series ICs

7.2.43 4040 (12-stage Binary Counter)

The 4040 device is a 12-stage binary ripple counter with a clock input (CP), an overriding
asynchronous master reset input (MR) and twelve fully buffered outputs (O0 to O11).
12-stage binary counter truth table:
CP MR O0-O11
‚ 0 Count
‚ 1 0

7.2.44 4041 (Quad True/Complement BUFFER)

This device provides both inverted and non-inverted buffered outputs for each input.
Logic function:
O = I
O = I

Multisim 8 Component Reference Guide 7-33

CMOS

Buffer gate truth table:

I 0 O
0 0 1
1 1 0

7.2.45 4042 (Quad D-latch)

This device contains four independent D-latches.

D-latch truth table:
En E1 On
0 0 Dn
0 1 Latched
1 0 Latched
1 1 Dn

7-34 Electronics Workbench

 4000 Series ICs

7.2.46 4043 (Quad RS latch w/3-state Out)

This device contains four independent RS-latches with 3-state outputs.

RS-latch truth table:

EO Sn Rn On
0 X X Z
1 0 1 0
1 1 X 1
1 0 0 Latched

7.2.47 4044 (Quad RS latch w/3-state Out)

This device contains four independent RS-latches with 3-state outputs.

Multisim 8 Component Reference Guide 7-35

CMOS

RS-latch truth table:

EO Sn Rn On
0 X X Z
1 0 1 1
1 X 0 0
1 1 1 Latched

7.2.48 4049 (Hex INVERTER)

This device contains six independent INVERTER gates.

Logic function:
O = I

INVERTER gate truth table:

I1 O1
1 0
0 1

7.2.49 4050 (Hex BUFFER)

This device contains six independent BUFFER/non-inverting gates.

Logic function:
Y = A

7-36 Electronics Workbench

 4000 Series ICs

BUFFER gate truth table:

A Y
0 0
1 1

7.2.50 4060 (14-Stage Binary Counter & Osc)

The HEF4060B is a 14-stage ripple-carry binary counter/divider and oscillator with three
oscillator terminals, ten buffered outputs and an overriding asynchronous master reset input. The
oscillator configuration allows design of either RC or crystal oscillator circuits. The oscillator
may be replaced by an external clock signal at input RS. The counter advances on the
negative-going transition of RS. A HIGH level on MR resets the counter (O3 to O9 and O11 to O13 =
LOW), independent of other input conditions. Schmitt-trigger action in the clock input makes the
circuit highly tolerant to slower clock rise and fall times.

7.2.51 4066 (Quad Analog Switches)

The 4066 device has four independent bilateral analogue switches (transmission gates). Each
switch has two input/output terminals (Y/Z) and an active HIGH enable input (E).
When the C input is high, the input/outputs A and B, will pass either digital or analog signals
in either direction.

Multisim 8 Component Reference Guide 7-37

CMOS

Analog switch truth table:

C A B
0 Z
1 <->

7.2.52 4068 (8-In NAND)

Logic function:

O1 = I0I1I2I3I4I5I6I7

NAND gate truth table:

INPUTS I0 THROUGH I7 O1
All inputs 1 0
One or more inputs |

7.2.53 4069 (Hex INVERTER)

This device contains six independent INVERTER gates.

7-38 Electronics Workbench

 4000 Series ICs

Logic function:
A = Y

INVERTER gate truth table:

A Y
0 1
1 0

7.2.54 4070 (Quad 2-In XOR)

This device contains four independent 2-input EXCLUSIVE-OR gates.

Logic function:
Y = A⊕B

EXCLUSIVE-OR gate truth table:

A B Y
0 0 0
0 1 1
1 0 1
1 1 0

7.2.55 4071 (Quad 2-In OR)

This device contains four independent 2-input OR gates.

Multisim 8 Component Reference Guide 7-39

CMOS

Logic function:
Y = A+B

OR gate truth table:

A B Y
0 0 0
1 0 1
0 1 1
1 1 1

7.2.56 4072 (Dual 4-In OR)

The 4072 device provides the positive dual 4-input OR function.

Logic function:
Y = A+B+C+D

7-40 Electronics Workbench

 4000 Series ICs

4-input OR gate truth table:

INPUTS OUTPUT
A B C D Y
0 0 0 0 0
0 0 0 1 1
0 0 1 0 1
0 0 1 1 1
0 1 0 0 1
0 1 0 1 1
0 1 1 0 1
0 1 1 1 1
1 0 0 0 1
1 0 0 1 1
1 0 1 0 1
1 0 1 1 1
1 1 0 0 1
1 1 0 1 1
1 1 1 0 1
1 1 1 1 1

7.2.57 4073 (Tri 3-In AND)

This device contains three independent 3-input AND gates.

Logic function:
Y = ABC

Multisim 8 Component Reference Guide 7-41

CMOS

AND gate truth table:

A B C Y
0 0 0 0
1 0 0 0
0 1 0 0
1 1 0 0
0 0 1 0
1 0 1 0
0 1 1 0
1 1 1 1

7.2.58 4075 (Tri 3-In OR)

This device contains three independent 3-input OR gates.

Logic function:
Y = A+B+C

OR gate truth table:

A B C Y
0 0 0 0
0 0 1 1
0 1 0 1
0 1 1 1
1 0 0 1
1 0 1 1
1 1 0 1
1 1 1 1

7-42 Electronics Workbench

 4000 Series ICs

7.2.59 4076 (Quad D-type Reg w/3-state Out)

The 4076 device is a quadruple edge-triggered D-type flip-flop with four data inputs (D0 to
D3), two active LOW data enable inputs (ED0 and (ED1), a common clock input (CP), four
3-state outputs (O0 to O3), two active LOW output enable inputs (EO0 and EO1), and an
overriding asynchronous master reset input (MR).

D-type register truth table:

INPUTS OUTPUTS
MR CP ED0 ED1 Dn On
1 X X X X 0
0 · 1 X X NO CHANGE
0 · X 1 X NO CHANGE
0 · 0 0 1 1
0 · 0 0 0 0
0 ‚ X X X NO CHANGE

7.2.60 4077 (Quad 2-In XNOR)

This device contains four independent 2-input EXCLUSIVE-NOR gates.

Multisim 8 Component Reference Guide 7-43

CMOS

Logic function:
O = A⊕B

EXCLUSIVE-NOR gate truth table:

An Bn On
0 0 1
0 1 0
1 0 0
1 1 1

7.2.61 4078 (8-In NOR)

Logic function:

8-input NOR gate simplified truth table:

7-44 Electronics Workbench

 4000 Series ICs

If one or more inputs are high, the output is low.

INPUTS OUTPUT
I0 I1 I2 I3 I4 I5 I6 I7 O1
0 0 0 0 0 0 0 0 1
1 X X X X X X X 0
X 1 X X X X X X 0
X X 1 X X X X X 0
X X X 1 X X X X 0
X X X X 1 X X X 0
X X X X X 1 X X 0
X X X X X X 1 X 0
X X X X X X X 1 0

7.2.62 4081 (Quad 2-In AND)

This device contains four independent 2-input AND gates.

Logic function:

Y = AB

AND gate truth table:

A B Y
0 0 0
1 0 0
0 1 0
1 1 1

Multisim 8 Component Reference Guide 7-45

CMOS

7.2.63 4082 (Dual 4-In AND)

This device contains two independent 4-input AND gates.

All 4-inputs on each 4-input gate must be high to obtain a high at the output.

Logic function:

Y = ABCD

AND gate truth table:

A B C D Y
0 0 0 0 0
0 0 0 1 0
0 0 1 0 0
0 0 1 1 0
0 1 0 0 0
0 1 0 1 0
0 1 1 0 0
0 1 1 1 0
1 0 0 0 0
1 0 0 1 0
1 0 1 0 0
1 0 1 1 0
1 1 0 0 0
1 1 0 1 0
1 1 1 0 0
1 1 1 1 1

7-46 Electronics Workbench

 4000 Series ICs

7.2.64 4085 (Dual 2-Wide 2-In AND-OR-INVERTER)

This device contains a combination of gates (AND, OR and INVERTER).

Logic function:

OA = A0•A1+A2•A3+A4
OB = B0•B1+B2•B3+B4

Multisim 8 Component Reference Guide 7-47

CMOS

Inverter gate truth table:

INPUTS OUTPUT
A0 A1 A2 A3 A4 OA
0 0 0 0 0 1
0 0 0 0 1 0
0 0 0 1 0 1
0 0 0 1 1 0
0 0 1 0 0 1
0 0 1 0 1 0
0 0 1 1 0 1
0 0 1 1 1 0
0 1 0 0 0 0
0 1 0 0 1 0
0 1 0 1 0 1
0 1 0 1 1 0
0 1 1 0 0 1
0 1 1 0 1 0
0 1 1 1 0 1
0 1 1 1 1 0
1 0 0 0 0 0
1 0 0 0 1 L
1 0 0 1 0 1
1 0 0 1 1 0
1 0 1 0 0 1
1 0 1 0 1 0
1 0 1 1 0 1
1 0 1 1 1 0
1 1 0 0 0 0
1 1 0 0 1 0
1 1 0 1 0 0
1 1 0 1 1 0
1 1 1 0 0 0
1 1 1 0 1 0
1 1 1 1 0 0
1 1 1 1 1 0

7-48 Electronics Workbench

 4000 Series ICs

7.2.65 4086 (4-Wide 2-In AND-OR-INVERTER)

This device contains a combination of gates (AND, OR and INVERTER).

Logic function:
O = I0I1+I2I3+I4I5+I6I7+I8+I9

Inverter gate truth table:

INPUTS OUTPUT
I0 I1 I2 I3 I4 I5 I6 I7 I8 ~I9 O
X X X X X X X X 1 X 0
X X X X X X X X X 0 0
1 1 X X X X X X X X 0
X X 1 1 X X X X X X 0
X X X X 1 1 X X X X 0
X X X X X X 1 1 X X 0
ANY OTHER COMBINATION OF INPUTS 1

7.2.66 4093 (Quad 2-In NAND (Schmitt))

This device contains four independent 2-input NAND gates. Due the to the Schmitt-trigger
action, this device is ideal for circuits that are susceptible to unwanted small signals, such as
noise.
Logic function:
O = A1B2

Multisim 8 Component Reference Guide 7-49

CMOS

NAND gate truth table:

A B Y
0 0 1
0 1 1
1 0 1
1 1 0

7.2.67 4094 (8-stage Serial Shift Register)

The 4094 device is an 8-stage serial shift register having a storage latch associated with each
stage for strobing data from the serial input to parallel buffered 3-state outputs O0 to O7.

Shift register truth table:

PARALLEL SERIAL
INPUTS
OUTPUTS OUTPUTS
CP EO STR D O0 On Os Os

0 X X Z Z O6 nc

0 X X Z Z nc O7

1 0 X nc nc O6 nc

1 1 0 0 On-1 O6 nc

1 1 1 1 On-1 O6 nc

1 1 1 nc nc nc O7

1 = HIGH state (the more positive voltage)

0 = LOW state (the less positive voltage)
X = state is immaterial
= positive-going transition
= negative-going transition
Z = high impedance off state

7-50 Electronics Workbench

 4000 Series ICs

7.2.68 4099 (8-bit Latch)

The 4099 device is an 8-bit addressable latch. The input for this device is a unidirectional
write only port.

7.2.69 4502 (Strobed hex INVERTER)

This device contains six independent INVERTER gates.

INVERTER gate truth table:

Dn E EO On
0 0 0 1
1 0 0 0
X 1 0 0
X X 1 Z

Multisim 8 Component Reference Guide 7-51

CMOS

7.2.70 4503 (Tri-state hex BUFFER w/Strobe)

Four of these six non-inverting buffers (I1 through I4) are enabled by a high on EN1 and the
last two (I5 and I6) are enabled by a high on EN2.
Buffer gate truth table:
I EN O
0 0 0
1 0 1
X 1 Z

Z = High impedance
X = Don’t care

7.2.71 4508 (Dual 4-bit latch)

This device contains two independent 4-bit latches.

7-52 Electronics Workbench

 4000 Series ICs

4-bit latch truth table:

INPUTS OUTPUTS
MR ST EO Dn On
0 1 0 1 1
0 1 0 0 0
0 0 0 X LATCHED
1 X 0 X 0
X X 1 X Z

7.2.72 4510 (BCD up/down Counter)

BCD up/down counter truth table:

MR PL UP/DN CE CP MODE
0 1 X X X PARALLEL LOAD
0 0 X 1 X NO CHANGE
0 0 0 0 · COUNT DOWN
0 0 1 0 · COUNT UP
1 X X X X RESET

Multisim 8 Component Reference Guide 7-53

CMOS

7.2.73 4511(BCD-to-seven segment latch/Dec)

The 4511 BCD (Binary-Coded Decimal)-to-seven-segment latch decoder translates a 4-bit

BCD input into hexadecimal, and outputs high on the output pins corresponding to the
hexadecimal representation of the BCD input. There are provisions for lamp testing and for
blanking the outputs.

INPUTS OUTPUTS
DISPLAY EL BI LT D C B A a b c d e f g
8 X X 0 0 0 0 0 1 1 1 1 1 1 0
X 0 1 0 0 0 0 1 1 1 1 1 1 0
0 0 1 1 0 0 0 0 1 1 1 1 1 1 0
1 0 1 1 0 0 0 1 0 1 1 0 0 0 0
2 0 1 1 0 0 1 0 1 1 0 1 1 0 1
3 0 1 1 0 0 1 1 1 1 1 1 0 0 1
4 0 1 1 0 1 0 0 0 1 1 0 0 1 1
5 0 1 1 0 1 0 1 1 0 1 1 0 1 1
6 0 1 1 0 1 1 0 0 0 1 1 1 1 0
7 0 1 1 0 1 1 1 1 1 1 0 0 0 0
8 0 1 1 1 0 0 0 1 1 1 1 1 1 1
9 0 1 1 1 0 0 1 1 1 1 0 0 1 1
0 1 1 1 0 1 0 0 0 0 1 1 0 1
0 1 1 1 0 1 1 0 0 1 1 0 0 1
0 1 1 1 1 0 0 0 1 0 0 0 1 1
0 1 1 1 1 0 1 1 0 0 1 0 1 1
0 1 1 1 1 1 0 0 0 0 1 1 1 1
0 1 1 1 1 1 1 0 0 0 0 0 0 0
* 1 1 1 0 0 0 0 *

7-54 Electronics Workbench

 4000 Series ICs

* Depends on BCD code applied during 0 to 1 transition of EL

EL = active-low latch enable input

BI = active-low ripple-blanking input
LT = active-low lamp-test input

7.2.74 4512 (8-In MUX w/3-state Out)

This device is a 8-input multiplexer with 3-state outputs.

Multisim 8 Component Reference Guide 7-55

CMOS

Multiplexer truth table:

INPUTS OUTPUT
SELECT DATA
EO E C B A I0 I1 I2 I3 I4 I5 I6 I7 O
0 1 X X X X X X X X X X X 0
0 0 0 0 0 0 X X X X X X X 0
0 0 0 0 0 1 X X X X X X X 1
0 0 0 0 1 X 0 X X X X X X 0
0 0 0 0 1 X 1 X X X X X X 1
0 0 0 1 0 X X 0 X X X X X 0
0 0 0 1 0 X X 1 X X X X X 1
0 0 0 1 1 X X X 0 X X X X 0
0 0 0 1 1 X X X 1 X X X X 1
0 0 1 0 0 X X X X 0 X X X 0
0 0 1 0 0 X X X X 1 X X X 1
0 0 1 0 1 X X X X X 0 X X 0
0 0 1 0 1 X X X X X 1 X X 1
0 0 1 1 0 X X X X X X 0 X 0
0 0 1 1 0 X X X X X X 1 X 1
0 0 1 1 1 X X X X X X X 0 0
0 0 1 1 1 X X X X X X X 1 1
1 X X X X X X X X X X X X Z

EO = Output Enable (Active-low)

E = Enable input (Active-low)

Z = High impedance

7-56 Electronics Workbench

 4000 Series ICs

7.2.75 4514 (1-of-16 Dec/DEMUX w/Input latches)

This device is a 1-of-16 decoder/demultiplexer with input latches. The input latches allow for
the user to hold a previous input with the enable input while the inputs change.

1-of-16 decoder/demultiplexer truth table:

INPUTS OUTPUTS
E A3 A2 A1 A0 O0 O1 O2 O3 O4 O5 O6 O7 O8 O9 O10 O11 O12 O13 O14 O15
1 X X X X 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 1 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 1 1 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0
0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0
0 0 1 0 1 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0
0 0 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0
0 0 1 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0
0 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
0 1 0 0 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0
0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0
0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0
0 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0
0 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1

Multisim 8 Component Reference Guide 7-57

CMOS

7.2.76 4515 (1-of-16 Dec/DEMUX w/Input latches)

This device is a 1-of-16 decoder/demultiplexer with input latches. The input latches allow for
the user to hold a previous input with the enable input while the inputs change.

1-of-16 decoder/demultiplexer truth table:

INPUTS OUTPUTS
E A3 A2 A1 A0 O0 O1 O2 O3 O4 O5 O6 O7 O8 O9 O10 O11 O12 O13 O14 O15
1 X X X X 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
0 0 0 0 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1
0 0 0 1 0 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1
0 0 0 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1
0 0 1 0 0 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1
0 0 1 0 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1
0 0 1 1 0 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1
0 0 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1
0 1 0 0 0 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1
0 1 0 0 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1
0 1 0 1 0 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1
0 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1
0 1 1 0 0 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1
0 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1
0 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 1
0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0

7-58 Electronics Workbench

 4000 Series ICs

7.2.77 4516 (Binary up/down Counter)

This binary up/down counter counts from 0000 to 1111 in binary (0 to 15 in decimal).

Binary up/down counter truth table:

MR PL UP/DN CE CP MODE
0 1 X X X PARALLEL LOAD
0 0 X 1 X NO CHANGE
0 0 0 0 · COUNT DOWN
0 0 1 0 · COUNT UP
1 X X X X RESET

7.2.78 4518 (Dual BCD Counter)

The 4518 device is a dual 4-bit internally synchronous BCD counter.

Multisim 8 Component Reference Guide 7-59

CMOS

BCD counter truth table:

CP0 CP1 MR MODE
· 1 0 COUNTER
ADVANCES
0 ‚ 0 COUNTER
ADVANCES
‚ X 0 NO CHANGE
X · 0 NO CHANGE
· 0 0 NO CHANGE
1 ‚ 0 NO CHANGE
X X 1 O0 TO O3 = LOW

7.2.79 4519 (Quad Multiplexer)

The 4519 device provides four multiplexing circuits with common select inputs (SA, SB).
Each circuit contains two inputs (An, Bn) and one output (On).

7.2.80 4520 (Dual Binary Counter)

The 4520 device is a dual 4-bit internally synchronous binary counter.

7-60 Electronics Workbench

 4000 Series ICs

Binary counter truth table:

CP0 CP1 MR MODE
· 1 0 COUNTER ADVANCES
0 ‚ 0 COUNTER ADVANCES
‚ X 0 NO CHANGE
X · 0 NO CHANGE
· 0 0 NO CHANGE
1 ‚ 0 NO CHANGE
X X 1 O0 TO O3 = LOW

7.2.81 4522 (4-bit BCD Down Counter)

The 4522 device is a synchronous programmable 4-bit BCD down counter with an active
HIGH and an active LOW clock input (CP0, CP1), an asynchronous parallel load input (PL),
four parallel inputs (P0 to P3), a cascade feedback input (CF), four buffered parallel outputs
(O0 to O3), a terminal count output (TC) and an overriding asynchronous master reset input
(MR).

7.2.82 4526 (4-bit Bin Down Counter)

Multisim 8 Component Reference Guide 7-61

CMOS

The 4526 device is a synchronous programmable 4-bit binary down counter with an active
HIGH and an active LOW clock input (CP0, CP1), an asynchronous parallel load input
(PL), four parallel inputs (P0 to P3), a cascade feedback input (CF), four buffered parallel
outputs (O0 to O3), a terminal count output (TC) and an overriding asynchronous master
reset input (MR).

7.2.83 4531 (13-input Checker/Generator)

The 4531 device is a parity checker/generator with 13 parity inputs (I0 to I12) and a parity
output (O).

Truth table:

INPUTS OUTPUTS
I0 I1 I2 I3 I4 I5 I6 I7 I8 I9 I10 I11 I12 O
0 0 0 0 0 0 0 0 0 0 0 0 0 0
any odd number of inputs HIGH 1
any even number of inputs HIGH 0
1 1 1 1 1 1 1 1 1 1 1 1 1 1

1 = HIGH state (the more positive voltage)

0 = LOW state (the less positive voltage)

7-62 Electronics Workbench

 4000 Series ICs

7.2.84 4532 (8-bit Priority Enc)

This device is an 8-bit priority encoder.

Priority encoder truth table:

INPUTS OUTPUTS
E1 0 1 2 3 4 5 6 7 GS O2 O1 O0 EO
0 X X X X X X X X 0 0 0 0 0
1 0 0 0 0 0 0 0 0 0 0 0 0 1
1 1 X X X X X X X 1 1 1 1 0
1 0 1 X X X X X X 1 1 1 0 0
1 0 0 1 X X X X X 1 1 0 1 0
1 0 0 0 1 X X X X 1 1 0 0 0
1 0 0 0 0 1 X X X 1 0 1 1 0
1 0 0 0 0 0 1 X X 1 0 1 0 0
1 0 0 0 0 0 0 1 X 1 0 0 1 0
1 0 0 0 0 0 0 0 1 1 0 0 0 0

Multisim 8 Component Reference Guide 7-63

CMOS

7.2.85 4539 (Dual 4-input Multiplexer)

The 4539 device is a dual 4-input multiplexer with common select logic. Each multiplexer
has four multiplexer inputs (I0 to I3), an active LOW enable input (E) and a multiplexer
output (O).

7.2.86 4543 (BCD-to-seven segment latch/dec/driver)

The 4543 device is a BCD to 7-segment latch/decoder/driver for liquid crystal and LED
displays. It has four address inputs (DA to DD), an active HIGH latch disable input (LD), an
active HIGH blanking input (BI), an active HIGH phase input (PH) and seven buffered
segment outputs (Oa to Og).

7-64 Electronics Workbench

 4000 Series ICs

7-segment latch/decoder/driver truth table:

INPUTS OUTPUTS
LD BI PH * DD DC DB DA Oa Ob Oc Od Oe Of Og DISPLAY
X 1 0 X X X X 0 0 0 0 0 0 0 BLANK
1 0 0 0 0 0 0 1 1 1 1 1 1 0 0
1 0 0 0 0 0 1 0 1 1 0 0 0 0 1
1 0 0 0 0 1 0 1 1 0 1 1 0 1 2
1 0 0 0 0 1 1 1 1 1 1 0 0 1 3
1 0 0 0 1 0 0 0 1 1 0 0 1 1 4
1 0 0 0 1 0 1 1 0 1 1 0 1 1 5
1 0 0 0 1 1 0 1 0 1 1 1 1 1 6
1 0 0 0 1 1 1 1 1 1 0 0 0 0 7
1 0 0 1 0 0 0 1 1 1 1 1 1 1 8
1 0 0 1 0 0 1 1 1 1 1 0 1 1 9
1 0 0 1 0 1 0 0 0 0 0 0 0 0 BLANK
1 0 0 1 0 1 1 0 0 0 0 0 0 0 BLANK
1 0 0 1 1 0 0 0 0 0 0 0 0 0 BLANK
1 0 0 1 1 0 1 0 0 0 0 0 0 0 BLANK
1 0 0 1 1 1 0 0 0 0 0 0 0 0 BLANK
1 0 0 1 1 1 1 0 0 0 0 0 0 0 BLANK
0 0 0 X X X X **
as above 1 as above inverse as above as above

1 = HIGH state (the more positive voltage)

0 = LOW state (the less positive voltage)
X = state is immaterial

* For liquid crystal displays, apply a square-wave to PH.

For common cathode LED displays, select PH = LOW.
For common anode LED displays, select PH = HIGH.
** Depends upon the BCD-code previously applied when LD = HIGH

Multisim 8 Component Reference Guide 7-65

CMOS

7.2.87 4544 (BCD-to-seven segment latch/dec)

The 4544 BCD (Binary-Coded Decimal) -to-seven segment latch/decoder/driver is designed

for use with liquid crystal readouts. It is constructed with complementary MOS (CMOS)
enhancement mode devices. The circuit provides the functions of a 4-bit storage latch and an
8421 BCD-to-seven segment decoder and driver.

7-66 Electronics Workbench

 4000 Series ICs

7-segment latch/decoder/driver truth table:

INPUTS OUTPUTS
RBI LD B1 Ph * D C B A RBO a b c d e f g DISPLAY
X X 1 0 X X X X 0 0 0 0 0 0 0 BLANK
1 1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 BLANK
0 1 0 0 0 0 0 0 0 1 1 1 1 1 1 0 0
X 1 0 0 0 0 0 1 0 0 1 1 0 0 0 0 1
X 1 0 0 0 0 1 0 0 1 1 0 1 1 0 1 2
X 1 0 0 0 0 1 1 0 1 1 1 1 0 0 1 3
X 1 0 0 0 1 0 0 0 0 1 1 0 0 1 1 4
X 1 0 0 0 1 0 1 0 1 0 1 1 0 1 1 5
X 1 0 0 0 1 1 0 0 1 0 1 1 1 1 1 6
X 1 0 0 0 1 1 1 0 1 1 1 0 0 0 0 7
X 1 0 0 1 0 0 0 0 1 1 1 1 1 1 1 8
X 1 0 0 1 0 0 1 0 1 1 1 1 0 1 1 9
X 1 0 0 1 0 1 0 0 0 0 0 0 0 0 0 BLANK
X 1 0 0 1 0 1 1 0 0 0 0 0 0 0 0 BLANK
X 1 0 0 1 1 0 0 0 0 0 0 0 0 0 0 BLANK
X 1 0 0 1 1 0 1 0 0 0 0 0 0 0 0 BLANK
X 1 0 0 1 1 1 0 0 0 0 0 0 0 0 0 BLANK
X 1 0 0 1 1 1 1 0 0 0 0 0 0 0 0 BLANK
X 0 0 0 X X X X ** **
† † † † † † Inverse of Output Display as
Combinations Above above

X Don’t care
† Above combinations
*
**
RBO=RBI • (ABCD)

7.2.88 4555 (Dual 1-of-4 Dec/DEMUX)

Multisim 8 Component Reference Guide 7-67

CMOS

The 4555 device is a dual 1-of-4 decoder/demultiplexer. Each has two address inputs (A0
and A1), an active LOW enable input (E) and four mutually exclusive outputs that are active
HIGH (O0 to O3).

Decoder/demultiplexer truth table:

INPUTS OUTPUTS
E A0 A1 O0 O1 O2 O3
0 0 0 1 0 0 0
0 1 0 0 1 0 0
0 0 1 0 0 1 0
0 1 1 0 0 0 1
1 X X 0 0 0 0

1 = HIGH state (the more positive voltage)

0 = LOW state (the less positive voltage)
X = state is immaterial

7.2.89 4556 (Dual 1-of-4 Dec/DEMUX)

This device contains two independent 1-of-4 decoders/demultiplexers.

Decoders/demultiplexer truth table:

INPUTS OUTPUTS
E A0 A1 O0 O1 O2 O3
0 0 0 0 1 1 1
0 1 0 1 0 1 1
0 0 1 1 1 0 1
0 1 1 1 1 1 0
1 X X 1 1 1 1

7-68 Electronics Workbench

 4000 Series ICs

7.2.90 4585 (4-bit Comparator)

The 4585 device is a 4-bit magnitude comparator that compares two 4-bit words (A and B),
whether they are “less than”, “equal to”, or “greater than”. Each word has four parallel inputs
(A0 to A3 and B0 to B3).

4-bit comparator truth table:

CASCADING
COMPARING INPUTS OUTPUTS
INPUTS
A3, B3 A2, B2 A1, B1 A0, B0 IA>B IA<B IA=B OA>B OA<B OA=B
A3>B3 X X X 1 X X 1 0 0
A3<B3 X X X X X X 0 1 0
A3=B3 A2>B2 X X 1 X X 1 0 0
A3=B3 A2<B2 X X X X X 0 1 0
A3=B3 A2=B2 A1>B1 X 1 X X 1 0 0
A3=B3 A2=B2 A1<B1 X X X X 0 1 0
A3=B3 A2=B2 A1=B1 A0>B0 1 X X 1 0 0
A3=B3 A2=B2 A1=B1 A0<B0 X X X 0 1 0
A3=B3 A2=B2 A1=B1 A0=B0 X 0 1 0 0 1
A3=B3 A2=B2 A1=B1 A0=B0 1 0 0 1 0 0
A3=B3 A2=B2 A1=B1 A0=B0 X 1 0 0 1 0
A3=B3 A2=B2 A1=B1 A0=B0 X 1 1 0 1 1
A3=B3 A2=B2 A1=B1 A0=B0 0 0 0 0 0 0

1 = HIGH state (the more positive voltage)

0 = LOW state (the less positive voltage)
X = state is immaterial

Multisim 8 Component Reference Guide 7-69

CMOS

7.3 Tiny Logic

Tiny Logic is a line of single function digital CMOS chips which are intended for applications
which require only a single gate to complete a design.

7.3.1 NC7S00
This device contains a single 2-input NAND gate.
Logic function:
Y = AB

NAND gate truth table:

A B Y
0 0 1
1 0 1
0 1 1
1 1 0

7.3.2 NC7S02
This device contains a single 2-input NOR gate.
Logic function:
Y = A+B

NOR gate truth table:

A B Y
0 0 1
1 0 0
0 1 0
1 1 0

7-70 Electronics Workbench

 Tiny Logic

7.3.3 NC7S04
This device contains a single inverter.
Logic function:
Y = A

INVERTER gate truth table:

A Y
1 0
0 1

7.3.4 NC7S08
This device contains a single 2-input AND gate.
Logic function:

Y = AB

AND gate truth table:

A B Y
0 0 0
1 0 0
0 1 0
1 1 1

7.3.5 NC7S32
This device contains a single 2-input OR gate.
Logic function:
Y = A+B

Multisim 8 Component Reference Guide 7-71

CMOS

OR gate truth table:

A B Y
0 0 0
1 0 1
0 1 1
1 1 1

7.3.6 NC7S86
This device contains a single 2-input exclusive-OR gate.
Exclusive-OR gate truth table:

INPUTS OUTPUT
A B Y
0 0 0
0 1 1
1 0 1
1 1 0

7.3.7 NC7ST00
This device contains a single 2-input NAND gate.
Logic function:
Y = AB

NAND gate truth table:

A B Y
0 0 1
1 0 1
0 1 1
1 1 0

7-72 Electronics Workbench

 Tiny Logic

7.3.8 NC7ST02
This device contains a single 2-input NOR gate.
Logic function:
Y = A+B

NOR gate truth table:

A B Y
0 0 1
1 0 0
0 1 0
1 1 0

7.3.9 NC7ST04
This device contains a single inverter.
Logic function:
Y = A

INVERTER gate truth table:

A Y
1 0
0 1

7.3.10 NC7ST08
This device contains a single 2-input AND gate.
Logic function:
Y = AB

Multisim 8 Component Reference Guide 7-73

CMOS

AND gate truth table:

A B Y
0 0 0
1 0 0
0 1 0
1 1 1

7.3.11 NC7ST32
This device contains a single 2-input OR gate.
Logic function:
Y = A+B

OR gate truth table:

A B Y
0 0 0
1 0 1
0 1 1
1 1 1

7.3.12 NC7ST86
This device contains a single 2-input exclusive-OR gate.
Exclusive-OR gate truth table:
INPUTS OUTPUT
A B Y
0 0 0
0 1 1
1 0 1
1 1 0

7-74 Electronics Workbench

 Tiny Logic

7.3.13 NC7SU04
This device contains a single unbuffered inverter.
Logic function:
Y = A

INVERTER gate truth table:

A Y
1 0
0 1

7.3.14 NC7SZ00
This device contains a single UHS (ultra high-speed) 2-input NAND gate.
Logic function:
Y = AB

NAND gate truth table:

A B Y
0 0 1
1 0 1
0 1 1
1 1 0

7.3.15 NC7SZ02
This device contains a single UHS (ultra high-speed) 2-input NOR gate.
Logic function:
Y = A+B

Multisim 8 Component Reference Guide 7-75

CMOS

NOR gate truth table:

A B Y
0 0 1
1 0 0
0 1 0
1 1 0

7.3.16 NC7SZ04
This device contains a single UHS (ultra high-speed) inverter.
Logic function:
Y = A

INVERTER gate truth table:

A Y
1 0
0 1

7.3.17 NC7SZ05
This device contains a single UHS (ultra high-speed) inverter with open drain output.
Logic function:
Y = A

INVERTER gate truth table:

A Y
1 0
0 1

7-76 Electronics Workbench

 Tiny Logic

7.3.18 NC7SZ08
This device contains a single UHS (ultra high-speed) 2-input AND gate.
Logic function:
Y = AB

AND gate truth table:

A B Y
0 0 0
1 0 0
0 1 0
1 1 1

7.3.19 NC7SZ125
This device contains a single UHS (ultra high-speed) buffer with 3-state output.
BUFFER gate truth table:
A Y

0 0
1 1

7.3.20 NC7SZ126
This device contains a single UHS (ultra high-speed) buffer with 3-state output.
BUFFER gate truth table:
A Y

0 0
1 1

Multisim 8 Component Reference Guide 7-77

CMOS

7.3.21 NC7SZ32
This device contains a single UHS (ultra high-speed) 2-input OR gate.
Logic function:
Y = A+B

OR gate truth table:

A B Y
0 0 0
1 0 1
0 1 1
1 1 1

7.3.22 NC7SZ38
This device contains a single UHS (ultra high-speed) 2-input NAND gate with open drain
output.
Logic function:
Y = AB

NAND gate truth table:

A B Y
0 0 1
1 0 1
0 1 1
1 1 0

7.3.23 NC7SZ86
This device contains a single UHS (ultra high-speed) 2-input exclusive-OR gate.

7-78 Electronics Workbench

 Tiny Logic

Exclusive-OR gate truth table:

INPUTS OUTPUT
A B Y
0 0 0
0 1 1
1 0 1
1 1 0

7.3.24 NC7SZU04
This device contains a single UHS (ultra high-speed) unbuffered inverter.
Logic function:
Y = A

INVERTER gate truth table:

A Y
1 0
0 1

Multisim 8 Component Reference Guide 7-79

CMOS

7-80 Electronics Workbench

Chapter 8
Misc. Digital Components

8.1 TIL Components

A number of TIL components are included in Multisim, including:
• “AND Gate” on page 8-1
• “OR Gate” on page 8-2
• “NOT Gate” on page 8-3
• “NOR Gate” on page 8-3
• “NAND Gate” on page 8-4
• “XOR Gate (Exclusive OR)” on page 8-4
• “XNOR Gate (Exclusive NOR)” on page 8-5
• “Tristate Buffer” on page 8-6
• “Buffer” on page 8-6
• “Schmitt Trigger” on page 8-7
• “Digital Pulldown” on page 8-8
• “Digital Pull-up” on page 8-8
• “Digital State Machine” on page 8-8
• “Parity Generator/Checker” on page 8-9
• “Quad 2-to-1 Data Sel/MUX” on page 8-9
• “Digital Frequency Divider” on page 8-9

8.1.1 AND Gate

This component has a high output only when all inputs are high.

Multisim 8 Component Reference Guide 8-1

Misc. Digital Components

AND gate truth table:

a b y
0 0 0
0 1 0
1 0 0
1 1 1

Boolean Expression:
y = a∗ b
y = a& b

8.1.2 OR Gate

This component has a high output when at least one input is high.
OR gate truth table:
a b y
0 0 0
0 1 1
1 0 1
1 1 1

Boolean Expression:

y = a+b
y=a b

8-2 Electronics Workbench

 TIL Components

8.1.3 NOT Gate

This component inverts, or complements, the input signal. If the input is high, the output is
low, and vice versa.

NOT gate truth table:

a y
0 1
1 0

Boolean Expression:
y = a′
y=a

8.1.4 NOR Gate

This component is a NOT OR, or an inverted OR gate. Its output is high only when all the
inputs are low. Using a NOR gate is the same as having a NOT gate at the output of an OR
gate.
NOR gate truth table:
a b y
0 0 1
0 1 0
1 0 0
1 1 0

Multisim 8 Component Reference Guide 8-3

Misc. Digital Components

Boolean Expression:
′
y = ( a + b)
y = a+b

8.1.5 NAND Gate

This component is a NOT AND, or inverted AND, gate. Its output is low only when all inputs
are high. Using a NAND gate is the same as having a NOT gate at the output of an AND gate.

NAND gate truth table:

a b y
0 0 1
0 1 1
1 0 1
1 1 0

Boolean Expression:

′
y = ( a∗ b )
y = a∗ b

8.1.6 XOR Gate (Exclusive OR)

This component has a high output when an odd number of inputs (1, 3, 5, etc.) is high. An
even number of high inputs generates a low output.

8-4 Electronics Workbench

 TIL Components

XOR gate truth table:

a b y
0 0 0
0 1 1
1 0 1
1 1 0

Boolean Expression:
y = a ⊕b
y = a ′b ′ + ab ′

8.1.7 XNOR Gate (Exclusive NOR)

This component has a high output when an even number of inputs (2, 4, 6, etc.) is high. An
odd number of high inputs generates a low output.

XNOR gate truth table:

a b y
0 0 1
0 1 0
1 0 0
1 1 1

Boolean Expression:

y = a⊕b
y = ( a ′b + ab ′ ) ′

Multisim 8 Component Reference Guide 8-5

Misc. Digital Components

8.1.8 Tristate Buffer

This component is a non-inverting buffer with a three-state output. It has a greater fan-out and
offers a high-current source and sink capability for driving high-current loads. The buffer has
an active-high enable input.
If the device is not “enabled”, then the buffer output goes into a high-impedance (Z) state. In
this state, the output pin is effectively disconnected from the rest of the circuit. Thus, the
buffer is useful for circuits where outputs from different digital devices meet at the same
node.
Truth table:
enable
input output
input
1 1 1
0 1 0
X 0 Z

where Z is a high-impedance state

Note When using a tristate buffer use the Models tab of the Circuit/Component Properties
dialog box. Select the LS-BUF or LS-OC-BUF (OC = Open-collector) model if the
buffer is being used as a TTL device. Select HC-BUF or HC-OD-BUF if the tristate
buffer is being used as a CMOS device. Otherwise, by default, the tristate buffer will
behave as a regular digital device without any high-current capabilities.

8.1.9 Buffer

This component is a non-inverting buffer. It has a greater fan-out and offers a high-current
source and sink capability for driving high-current loads.

8-6 Electronics Workbench

 TIL Components

Truth table:

input output
1 1
0 0

Note When using a buffer, set it up using the Models tab of the Circuit/Component
Properties dialog box. Select the LS-BUF or LS-OC-BUF model if the buffer is being
used as a TTL device. Select HC-BUF or HC-OD-BUF if the buffer is being used as a
CMOS device. Otherwise, by default, the buffer will behave as a regular digital device
without any high-current capabilities.

8.1.10 Schmitt Trigger

This component is a type of comparator with hystereses that produces uniform-amplitude

output pulses from a random-amplitude input signal. It has applications in pulse systems, for
example, converting a sine wave into a square wave.
Characteristic Operation:
The Schmitt trigger outputs:

0 if the voltage is rising and Vin > V+g+

1 if the voltage is falling and Vin < V+g-

where

V+g+ = 1.6 V (Vih)

V+g- = 0.9 V (Vil)

Multisim 8 Component Reference Guide 8-7

Misc. Digital Components

8.1.11 Digital Pulldown

A digital pull-down resistor emulates the behavior of an analog resistance value tied to a low
voltage level.

8.1.12 Digital Pull-up

A digital pull-up resistor emulates the behavior of an analog resistance value tied to a high
voltage level.

8.1.13 Digital State Machine

The digital state machine’s model can be configured to act as most types of counter or clocked
combinational logic blocks. Use this device to replace large digital schematics.

8-8 Electronics Workbench

 TIL Components

8.1.14 Parity Generator/Checker

This 9-bit (8 data bits plus 1 parity bit) parity generator/checker features odd/even outputs and
control inputs to facilitate operation in either odd- or even-parity applications.
Parity generator/checker truth table:

INPUTS OUTPUTS

S OF H’s AT A S S
EVEN ODD
THRU H EVEN ODD
Even 1 0 1 0
Odd 1 0 0 1
Even 0 1 0 1
Odd 0 1 1 0
X 1 1 0 0
X 0 0 1 1

8.1.15 Quad 2-to-1 Data Sel/MUX

This device contains inverters and drivers to supply full on-chip data selection to the four
output gates. It presents inverted data to minimize propagation delay time.
A 4-bit word is selected from one of two sources and is routed to the four outputs.
Data selector/multiplexer truth table:

STROBE SELECT OUTPUT

G A/B A B Y
1 X X X 1
0 0 0 X 1
0 0 1 X 0
0 1 X 0 1
0 1 X 1 0

8.1.16 Digital Frequency Divider

This device is a programmable step-down divider which accepts an arbitrary divisor, a duty-
cycle term and an initial count value. The generated output is synchronized to the rising edges
of the input signal. Rise and fall delay on the outputs are independently specifiable.

Multisim 8 Component Reference Guide 8-9

Misc. Digital Components

8.2 VHDL
The components in the VHDL family are digital components in VHDL. The models were
obtained from the Free Model Foundation (http://www.fmf.org). The source for these
components is installed by default in the vhdl\fmfparts subdirectory of the Multisim directory.
In that sudirectory, the VHDL description files named with the form ‘STDxx’, for example,
model the equivalent component in the TTL ‘74xx’ series (e.g.: STD00.vhd is the VHDL
description for the 7400).
ECL10016.VHD: 4-Bit Synchronous Binary Up Counter
ECL10102.VHD: 2-input NOR and 2-input OR/NOR
ECL10104.VHD: 2-input AND and 2-input AND/NAND
ECL10124.VHD: TTL-to-ECL Translator
ECL10131.VHD: Dual D Flip-Flop with Set, Reset and Clock Enable
ECL10141.VHD: 4-Bit Universal Shift Register
IF75155.VHD: RS-232 Driver/Receiver
IF75172.VHD: Quad Differential Line Drivers
IF75173.VHD: Quad Differential Line Receivers
IF75179.VHD: Differential Driver/Receiver Pair
IF75188.VHD: RS-232 Quad Line Driver
IF75189.VHD: RS-232 Line Receiver
STD00.VHD: 2-input positve-NAND gate
STD01.VHD: 2-input positve-NAND gate with open-collector output
STD02.VHD: 2-input positve-NOR gate
STD03.VHD: 2-input positve-NAND gate with open-collector output
STD04.VHD: Inverter
STD05.VHD: Inverter
STD06.VHD: Inverter with open collector output
STD07.VHD: Buffer/Driver with Open Collector Outputs
STD08.VHD: 2-input positve-AND gate
STD10.VHD: 3-input NAND gate
STD109.VHD: Positive-Edge Triggered J-K Flip-Flop
STD11.VHD: 3-input positve-AND gate
STD125.VHD: Line driver with 3-state output
STD132.VHD: 2-input positve-NAND gate

8-10 Electronics Workbench

 VHDL

STD138.VHD: 3 to 8 decoder
STD139.VHD: 2 to 4 decoder
STD14.VHD: Inverter
STD157.VHD: 2:1 Mux with enable
STD16260.VHD: Multiplexed D Latch with 3-State Outputs
STD16500.VHD: Universal Bus Transceiver
STD16501.VHD: Universal Bus Transceiver
STD16601.VHD: Universal Bus Transceiver
STD240.VHD: Inverting line driver with 3-state output
STD244.VHD: Line driver with 3-state output
STD245.VHD: 8-bit TTL Transceiver
STD257.VHD: 2:1 Mux with 3-state output
STD258.VHD: 2:1 Mux with 3-state inverting output
STD26.VHD: 2-input positve-NAND gate with open-collector output
STD273.VHD: D Flip-Flop with Clear
STD32.VHD: 2-input positve-OR gate
STD373.VHD: Transparent Latch
STD374.VHD: Positive-Edge Triggered Flip-Flop
STD377.VHD: Octal D-Type Flip-Flop with Enable (8-Bit Hold Register)
STD38.VHD: Quadruple 2-input positve-NAND buffers
STD521.VHD: 8-Bit Identity Comparator
STD533.VHD: D Latch with 3-State Outputs
STD541.VHD: Driver with 3-state output
STD543.VHD: Latched Transceiver
STD544.VHD: Inverting Latched Transceiver
STD574.VHD: Positive-Edge Triggered Flip-Flop
STD640.VHD: Bidirectional Bus Transceiver
STD652.VHD: Registered Bus Transceiver with 3-State Output
STD74.VHD: Positive-Edge Triggered Flip-Flop
STD821.VHD: Bus Interface Flip-Flop with 3-State Output
STD823.VHD: Bus Interface Flip-Flop with 3-State Output
STD825.VHD: Buffer with 3-state output

Multisim 8 Component Reference Guide 8-11

Misc. Digital Components

STD827.VHD: Buffer with 3-state output

STD832.VHD: 2-input positve-OR gate
STD86.VHD: 2-input exclusive-OR gate
STD869.VHD: Synchronous 8-Bit Up/Down Counter
STD952.VHD: Registered Transceiver with 3-State Output
STDH244.VHD: Line driver with 3-state output and bus hold
STDH245.VHD: TTL Transceiver with bus hold
STDH374.VHD: Positive-Edge Triggered Flip-Flop with bus hold
STDH543.VHD: Latched Transceiver with bus hold
STDH652.VHD: Reg Bus Transceiver with 3-State Output and Bus Hold
STDH952.VHD: Registered Transceiver with 3-State Output and bus hold
SY69167.VHD: 64 X 18 FIFO

8.3 Memory
A number of EPROM and RAM memory devices are included in Multisim. In addition to the
components that contain footprint and model information (for simulation), there are several
that include only the footprint, for PCB layout.

8.4 Line Receiver

Line receivers are devices which are used in applications such as a bridge between analog
signal and digital signals such as RS232 interfaces, or long signal runs over cables. The line
receivers are placed at the receiving end of the application before the digital circuits.

8.5 Line Driver

Line drivers are devices which are used in applications such as a bridge between analog signal
and digital signals such as RS232 interfaces, or long signal runs over cables. The line drivers
are placed at the transmitting end of the application after the digital circuits.

8-12 Electronics Workbench

 Line Transceiver

8.6 Line Transceiver

Line transceivers are devices, which are used in applications such as a bridge between analog
signal and digital signals such as RS232 interfaces, or long signal runs over cables. The line
transceivers are placed between the digital circuits.

8.7 CPLDs

A number of CPLDs (Complex Programmable Logic Devices) are included that have symbols
for layout purposes. These also have footprint, but no model information.

8.8 DSP Devices

A number of DSPs (Digital Signal Processors) are included that have symbols for layout
purposes. These also have footprint, but no model information.

Multisim 8 Component Reference Guide 8-13

Misc. Digital Components

8.9 FPGA Devices

A number of FPGAs (Field Programmable Gate Arrays) are included that have symbols for
layout purposes. These also have footprint, but no model information.

8.10 Microcontrollers

A number of microcontrollers are included that have symbols for layout purposes. These also
have footprint, but no model information.

8-14 Electronics Workbench

 Programmable Logic Devices

8.11 Programmable Logic Devices

A number of PLDs (Programmable Logic Devices) are included that have symbols for layout
purposes. These also have footprint, but no model information.

8.12 Microprocessors

A number of microprocessors are included that have symbols for layout purposes. These also
have footprint, but no model information.

Multisim 8 Component Reference Guide 8-15

Misc. Digital Components

8-16 Electronics Workbench

Chapter 9
Mixed Components

9.1 ADC DAC

An ADC is a special type of encoder that converts the input analog voltage to an equivalent
output digital word.

9.1.1 Characteristic Equation

The Vin input is the analog voltage input. The voltage at Vref+ and Vref- pins set up the full-scale
voltage. The full-scale voltage is given by:
Vfs = Vref + − Vref −
To start the conversion, the SOC pin should be driven high. This pulls the EOC pin low,
signifying that a conversion is taking place. The conversion takes 1 µS to complete and the
EOC pin is pulled high when it is completed. The output digital data is now available at pins

Multisim 8 Component Reference Guide 9-1

Mixed Components

D0 through D7. These are tri-stated outputs pins which may be enabled by pulling the OE pin
high.
The output at the end of the conversion process is the digital equivalent of the analog input
voltage. The discrete value corresponding to the quantized level of input voltage is given by:
input voltage * 256
Vfs

Note that the output described by this formula is not a continuous function of input voltage.
The discrete value is then encoded into the binary digital form at pins D0 through D7. The
binary output is thus given by:

 input voltage *256 

BIN  
 Vfs 

9.2 Analog Switch

This switch is a resistor that varies logarithmically between specified values of a controlling
input voltage. Note that the input is not internally limited. Therefore, if the controlling signal
exceeds the specified Coff or Con values, the resistance may become excessively large or
small.
The voltage controlled switch has a function similar to that performed by a mechanical On/
Off switch except that the On/Off conditions are selected by a control voltage.
When the control voltage is below a selected value, the switch is off and the input and output
signals are disconnected.
When the control voltage is above the selected value, the switch is on and the input and output
signals are connected.

9-2 Electronics Workbench

 Timer

9.3 Timer

The 555 timer is an IC chip that is commonly used as an astable multivibrator, a monostable
multivibrator or a voltage-controlled oscillator. The 555 timer consists basically of two
comparators, a resistive voltage divider, a flip-flop and a discharge transistor. It is a two-state
device whose output voltage level can be either high or low. The state of the output can be
controlled by proper input signals and time-delay elements connected externally to the 555
timer.

9.3.1 Model
The resistive voltage divider is used to set the voltage comparator levels. All three resistors
are of equal value. The upper comparator has a reference voltage of 2/3 Vcc and the lower
comparator has a reference of 1/3 Vcc. The comparator’s output controls the state of the flip-
flop and hence the output. When the trigger voltage goes below 1/3 Vcc, the output of the
lower comparator goes high, and the flip-flop sets. The output thus jumps to a high level. The
threshold input is normally connected to an external RC timing network. When the external
voltage exceeds 2/3 Vcc, the upper comparator’s output goes high and resets the flip-flop,
which in turn switches the output back to the low level. When the device output is low, the
discharge transistor, Q, is turned on and provides a path for the discharge of the external
timing capacitor.
This basic operation allows the timer to be configured with external components as an
oscillator, a monoshot or a time-delay element.

Multisim 8 Component Reference Guide 9-3

Mixed Components

9.4 Mono Stable

This component produces an output pulse of a fixed duration in response to an “edge” trigger
at its input. The length of the output pulse is controlled by the timing RC circuit connected to
the monostable multivibrator.

9.4.1 Model
A monostable multivibrator has two digital inputs: A1 and A2. The multivibrator can be
triggered by a positive edge of digital signal at A1 or a negative edge at A2. Once triggered, it
ignores further inputs.
An RC combination connected to RT/CT and CT pins controls the duration of the pulse
produced by the monostable at Q. A complementary output is produced at W.

To operate the monostable, the following connections may be used:
• Connect a series resistor (R) and capacitor (C) to the CT input.
• Connect the junction of the R and C to the RT/CT.
• Connect VCC to a voltage source.
The output Q will give a pulse of duration 0.0693*R*C when either a positive clock edge is
given to A1 or a negative edge is given to A2.
The threshold voltage (at which triggering starts) can be changed by modifying the model.

9.5 Phase-Locked Loop

This component models the behavior of a phase-locked loop circuit, which is a circuit that
contains an oscillator whose output phase and frequency are steered to keep it synchronized
with an input reference signal.
A phase-locked loop circuit is composed of three functional blocks: a phase detector, a low-
pass filter and a voltage-controlled oscillator (VCO). The phase detector behaves as an analog
multiplier. It outputs a DC voltage which is a function of the phase difference between the

9-4 Electronics Workbench

 Phase-Locked Loop

input reference signal and the VCO output signal. The output of the phase detector is input to
the low-pass filter, which removes the high-frequency noise and outputs a DC voltage. The
VCO converts the DC voltage into its corresponding frequency signal.

9.5.1 Characteristic Equation

The phase detector is modeled by:

Vd = Kd ∗ sin(ϕ i − ϕ o )
ϕ = 2π ∗ ∫ f (t )dt
The low-pass filter is modeled by a simple passive RC low-pass filter, that is, a resistor and a
capacitor, where R is 3.6 kohm, and:

1
C=
2π ∗ f p ∗ R

The voltage-controlled oscillator (VCO) is modeled by:

f o (t ) = f c + K o ∗Vc (t )
ϕ o = 2π ∗ ∫ f o (t )dt
where

fi = input frequency

fp = low-pass filter pole location

fo = VCO output frequency

fc = VCO free-running frequency

Vd = phase detector output DC voltage

Vo = VCO output voltage

Ko = VCO conversion gain

Kd = phase detector conversion gain

ϕi = input signal phase

ϕo = VCO output phase

Multisim 8 Component Reference Guide 9-5

Mixed Components

9.5.2 Phase-Locked Loop Parameters and Defaults

Symbol Parameter name Default Unit

Kd Phase detector conversion gain 0.25 V/rad

Ko VCO conversion gain 500 kHz/

V

fc VCO free-running frequency 250 kHz

fp Low-pass filter cut-off frequency 25 kHz

Vom VCO output amplitude 1.0 V

-- PLL Input Offset 0 V

-- PD Input Offset 0 V

-- VCO Output Offset 0 V

9.6 Multivibrators

9.6.1 CD4538BC
The CD4538 is a dual, precision monostable multivibrator with independent trigger and reset
controls. The device is retriggerable and resettable, and the control inputs are internally
latched. Two trigger inputs are provided to allow either rising or falling edge triggering. The
reset inputs are active LOW and prevent triggering while active. The pulse duration and
accuracy are determined by external components RX and CX. The device does not allow the
timing capacitor to discharge through the timing pin on power-down condition. For this

9-6 Electronics Workbench

 Multivibrators

reason, no external protection resistor is required in series with the timing pin. Input
protection from static discharge is provided on all pins.

9.6.2 SN74121N
This multivibrator has dual negative-triggered inputs and a single positive-transition-triggered
input which can be used as an inhibit input. Complementary output pulses are provided.

Multisim 8 Component Reference Guide 9-7

Mixed Components

9.6.3 SN74123
This DC triggered multivibrator has output pulse duration control by three methods. The basic
pulse time is programmed by selection of external resistance and capacitance values. Enough
Schmitt hysteresis is provided to ensure jitter-free triggering from the B input with transition
rates as slow as 0.1 mV per nanosecond.

9.6.4 SN74130N
This DC triggered multivibrator has output pulse duration control by three methods. The basic
pulse time is programmed by selection of external resistance and capacitance values.

9.7 Frequency Divider

This is an Asynchronous Binary Counter Based Frequency Divider. The amplitude of the
square wave output can be defined by the user via the dialog box. This device is ideal for use
with the virtual PLL in frequency synthesis applications.

9-8 Electronics Workbench

Chapter 10
Indicators

10.1 Voltmeter

The voltmeter offers advantages over the multimeter for measuring voltage in a circuit. You
can use an unlimited number of voltmeters in a circuit and rotate their terminals to suit your
layout.

10.1.1 Resistance (1.0 Ω - 999.99 TΩ)

The voltmeter is preset to a very high resistance (1 MΩ(+)) which generally has no effect on
a circuit. If you are testing a circuit that itself has very high resistance, you may want to
increase the voltmeter’s resistance to get a more accurate reading. (However, using a
voltmeter with very high resistance in a low-resistance circuit may result in a mathematical
round-off error.)

10.1.2 Mode (DC or AC)

The voltmeter can measure DC or AC voltage. In DC mode, any AC component of the signal
is eliminated so that only the DC component of the signal is measured. In AC mode, any DC
component is eliminated so that only the AC component is measured. When set to AC, the
voltmeter displays the root-mean-square (RMS) value of the signal.

Multisim 8 Component Reference Guide 10-1

Indicators

10.1.3 Connecting a Voltmeter

Connect the voltmeter in parallel with the load, attaching the probes to connectors on either
side of the load you want to measure. When a circuit is activated and its behavior is simulated,
the voltmeter displays the voltage across the test points. (The voltmeter may also display
interim voltages before the final steady-state voltage is reached.)
Note If a voltmeter is moved after the circuit has been simulated, activate the circuit again to
get a reading.

10.2 Ammeter

The ammeter offers advantages over the multimeter for measuring current in a circuit. You
can use an unlimited number of ammeters in a circuit and rotate their terminals to suit your
layout.

10.2.1 Resistance (1.0 pΩ - 999.99 Ω)

The ammeter’s resistance is preset to 1 mΩ, which presents little resistance to a circuit. If you
are testing a circuit that has low resistance, you can lower the ammeter’s resistance even
further to get a more precise measurement. (However, using an ammeter with very low
resistance in a high-resistance circuit may result in a mathematical round-off error.)

10.2.2 Mode (DC or AC)

The ammeter is preset to DC mode, which measures only the DC component of a signal. If
you want to measure the current from an AC source, change the mode to AC. When set to AC,
the ammeter displays the root-mean-square (RMS) value of the alternating signal.

10.2.3 Connecting an Ammeter

Like a real ammeter, the simulated ammeter must be connected in series at nodes you want to
measure. The negative terminal is on the side with the heavy border. If an ammeter is moved
after the circuit has been simulated, activate the circuit again to get a reading.

10-2 Electronics Workbench

 Probe (LED)

10.3 Probe (LED)

The probe indicates high (on) or low (off) levels at any point in a digital circuit. It lights up or
turns off as the circuit is running. You can change the color of the probe from the Choose
Probe tab of the Circuit/Component Properties dialog box.

10.4 Lamp

The lightbulb is an ideal, nonlinear resistive component that dissipates energy in the form of
light. It has two rated values, maximum power (Pmax) and maximum voltage (Vmax). Pmax is
measured in watts, from mW to kW. Vmax is measured in volts, from mV to kV. A bulb will
burn out if the voltage across it exceeds Vmax. At that point, the power dissipated in the bulb
exceeds Pmax.

10.4.1 Time-Domain and AC Frequency Models

The bulb is modeled by a resistor, R.

V max 2
R= if Vab ≤ Vmax
P max
R=∞ if Vab > Vmax
The bulb is lit if
Vmax
< Vab ≤ Vmax
2

Multisim 8 Component Reference Guide 10-3

Indicators

where

Vmax = the maximum voltage that can be applied across the bulb

Pmax = the maximum power that can be dissipated by the bulb.

For AC circuits, Vmax is the peak value of the applied voltage, not its RMS value.

10.5 Hex Display

10.5.1 Seven-Segment Display

The seven-segment display actively shows its state while the circuit is running. The seven
terminals (left to right, respectively) control segments a to g. By giving the proper binary-digit
inputs to segments a to g, you can display decimal numbers from 0 to 9 and letters A to F.

10-4 Electronics Workbench

 Hex Display

Truth table:

a b c d e f g Digit displayed

0 0 0 0 0 0 0 none
1 1 1 1 1 1 0 0
0 1 1 0 0 0 0 1
1 1 0 1 1 0 1 2
1 1 1 1 0 0 1 3
0 1 1 0 0 1 1 4
1 0 1 1 0 1 1 5
1 0 1 1 1 1 1 6
1 1 1 0 0 0 0 7
1 1 1 1 1 1 1 8
1 1 1 1 0 1 1 9
1 1 1 0 1 1 1 A
0 0 1 1 1 1 1 b
1 0 0 1 1 1 0 C
0 1 1 1 1 0 1 d
1 0 0 1 1 1 1 E
1 0 0 0 1 1 1 F

Multisim 8 Component Reference Guide 10-5

Indicators

10.5.2 Decoded Seven-Segment Display

This display indicates its current state by displaying hexadecimal digits—numerals 1 to 9 and
letters A to F. It is easier to use than the regular seven-segment display because it is already
decoded. Each hexadecimal digit is displayed when its 4-bit binary equivalent is received as
input, as shown in the truth table below.
Truth table:

a b c d Digit displayed

0 0 0 0 0
0 0 0 1 1
0 0 1 0 2
0 0 1 1 3
0 1 0 0 4
0 1 0 1 5
0 1 1 0 6
0 1 1 1 7
1 0 0 0 8
1 0 0 1 9
1 0 1 0 A
1 0 1 1 b
1 1 0 1 C
1 1 0 0 d
1 1 1 0 E
1 1 1 1 F

10-6 Electronics Workbench

 Bargraphs

10.6 Bargraphs

10.6.1 The Component

This display is an array of 10 LEDs arranged side by side. This component may be used to
indicate visually the rise and fall of a voltage. The voltage to be measured needs to be decoded
into levels using comparators which are used to drive each individual LED.
The terminals on the left side of the display are anodes and the terminals on the right are
cathodes. Each LED lights up when the turn-on current, Ion, flows through it. You can change
the voltage drop in the Value tab of the Circuit/Component Properties dialog box.

10.6.1.1 Bargraph Display Parameters and Defaults

Symbol Parameter Name Default Unit

Vf Forward voltage drop 2 V

If Forward current at which Vf is measured 0.03 A

Ion Forward current 0.01 A

10.6.2 Decoded Bargraph Display

This display consists of 10 LEDs arranged side by side, just like the regular bargraph display.
The difference is that the decoded bargraph display already has the decoding circuitry built-in
so that it only requires the voltage to be measured as an input to the display. The circuitry
inside decodes the voltage and lights up the appropriate number of LEDs, depending on the
voltage level.
The decoded bargraph display also offers a very high resistance to the input voltage. The
minimum voltages required for the lowest LED and the highest LED are set in the Value tab

Multisim 8 Component Reference Guide 10-7

Indicators

of the Circuit/Component Properties dialog box. The voltage at which each LED (from
lowest to highest) lights up is given by the formula:

(Vh − Vl ) ∗ n − 1
Von = Vl + ( )
9
where

n = 1, 2, ..., 10 (the number of the LED)

Other terms in this formula are defined in the table below.

10.6.2.1 Decoded Bargraph Display Parameters and

Defaults

Symbol Parameter Name Default Unit

Vl Minimum turn-on voltage required for 1 V

the lowest segment

Vh Minimum turn-on voltage required for 10 V

the highest segment

10.7 Buzzer/Sonalert Buzzer

This component uses the computer’s built-in speaker to simulate an ideal piezoelectric buzzer.
A piezoelectric buzzer sounds at a specific frequency when the voltage across its terminals
exceeds the set voltage.

10-8 Electronics Workbench

 Buzzer/Sonalert Buzzer

The buzzer is simulated as a single resistor whose resistance value is dependent on the
buzzer’s rated voltage and the current. It beeps when the voltage across its terminals exceeds
its voltage rating, Vrated.
Buzzer resistance
V rated
r=
i rated
Beeps when
V ab ≥ V rated

Multisim 8 Component Reference Guide 10-9

Indicators

10-10 Electronics Workbench

Chapter 11
Misc. Components

11.1 Crystal

This component is made of pure quartz and behaves as a quartz crystal resonator, a circular
piece of quartz with electrodes plated on both sides mounted inside an evacuated enclosure.
When quartz crystals are mechanically vibrated, they produce an AC voltage. Conversely,
when an AC voltage is applied across the quartz crystals, they vibrate at the frequency of the
applied voltage. This is known as the piezoelectric effect and quartz is an example of a
piezoelectric crystal.
The piezoelectric characteristics of quartz give the crystal the characteristics of a very high Q
tuned circuit. The piezoelectric effect of quartz crystal links the mechanical and electrical
properties of the resonator. Electrode voltage causes mechanical movement. Likewise,
mechanical displacement generates an electrode voltage.
An equivalent circuit for a crystal shows a large inductor in series with a small resistance and
a capacitance. When mounted in a holder with connections, a shunt capacitance is added to
the equivalent circuit. The resultant equivalent circuit means that the crystal has both a series
and parallel resonant frequency very close together.
Oscillators that employ crystals, typically quartz, offer excellent oscillation frequency
stabilities of 0.001 percent. Crystal oscillators are used in digital wristwatches and in clocks
that do not derive their frequency reference from the AC power line. They are also used in
color television sets and personal computers. In these applications, one or more “quartz
crystals” control frequency or time.
Another much more efficient transducer material than quartz is PZT. This ceramic material is
ferroelectric and is made up of lead and other atoms, Ti or Zr. PZT consists of randomly

Multisim 8 Component Reference Guide 11-1

Misc. Components

oriented crystallites of varying size. The piezoelectric but not the ferroelectric property of the
ceramic materials of the PZT family is made use of in transducer applications, such as
ultrasonic echo ranging (sonar), medical diagnostic ultrasound and nondestructive testing
system devices.

11.2 DC Motor

The component is a universal model of an ideal DC motor which can be used to model the
behavior of a DC motor excited in parallel, in series or separately. The excitation type of the
component is determined by the interconnection of the terminals between field windings
(terminals 1 and 2) and armature windings (terminals 3 and 4).
To excite the DC motor in parallel, connect the positive terminal of a DC source to terminals 2
and 4; then connect the negative terminals of the DC source to terminals 1 and 3. To excite the
DC motor in series, connect terminal 2 to terminal 3 (use a connector); then connect the
positive terminal of a DC source to terminal 4 and connect the negative terminal of the DC
source to terminal 1. To excite the DC motor separately, connect a DC source to terminals 2
and 1 (positive and negative, respectively); then connect another DC source to terminals 4 and
3 (positive and negative, respectively).
Terminal 5 is the DC motor’s output. The output is the motor’s rpm value.

To display this value:
• attach a voltmeter to terminal 5 (connect the other side of the voltmeter to ground) and
simulate
or
• attach the oscilloscope to terminal 5 and simulate (the rpm value is the voltage that
appears)
or
• attach a connector to terminal 5, then choose an appropriate analysis from the Analysis
menu (for example, if you choose Analysis/DC Operating Point, the rpm value is the
voltage at the connector).
This component connects the electrical and mechanical parts of a servo-system. Input to the
motor is electrical while output is mechanical.

11-2 Electronics Workbench

 DC Motor

11.2.1 Characteristic Equations

The characteristic equations of an ideal DC motor are given by:

dia
Va = Ra ∗ ia + La + Km ∗ i f ∗ ω m
dt
di f
Vf = R f ∗ i f + L f
dt
dω m
J + B f ∗ ω m + TL = Km ∗ i f ∗ ia
dt
where

ωm = rotational speed

Km = EMF constant

Va = armature voltage

Vf = field voltage

Other terms are defined in “DC Motor Parameters and Defaults”.

The EMF constant Km is determined by:

VaN − I a N ∗ Ra
Km =
2π * n N
I fN ∗
60
where
V fN
I fN = for separately excited DC motor
Rf
V fN VaN
I fN = = for parallel excited DC motor
Rf Rf
V fN
I fN = = I aN for series excited DC motor
Rf

Multisim 8 Component Reference Guide 11-3

Misc. Components

11.2.2 DC Motor Parameters and Defaults

Symbol Parameter Name Default Unit

Ra Armature resistance 1.1 Ω

La Armature inductance 0.001 H

Rf Field resistance 128 Ω

Lf Field inductance 0.001 H

Bf Shaft friction 0.01 N m*s/rad

J Machine rotational inertia 0.01 N*m*s2/rad

nn Rated rotational speed 1800 RPM

Van Rated armature voltage 115 V

Ian Rated armature current 8.8 A

Vfn Rated field voltage 115 V

Tl Load torque 0.0 N *m

11.3 Optocoupler

An optocoupler is a device that uses light to couple a signal from its input (a photoemitter) to
its output (a photodetector).
A typical optocoupler can be found in a six-pin dual in-line package (DIP) containing both an
LED and a photodetector, and a transistor Darlington pair or SCR. The wavelength response
of each device is structured to be as identical as possible to permit the highest measure of
coupling possible.

11-4 Electronics Workbench

 Vacuum Tube

11.4 Vacuum Tube

This component behaves as a three-electrode tube consisting of an anode, cathode and plate
electrode. It is often used as an amplifier in audio applications.
The vacuum tube is a voltage controlled current device, very similar in operation to an N
channel FET.
As for an FET, the gain of the tube is referred to as transconductance and is defined as the
change in plate current resulting from a change in grid to cathode voltage

gm = (change in plate current) / (change in grid to cathode voltage)

11.4.1 Characteristic Equations

The DC characteristic of the triode vacuum tube is modeled by a two-dimensional voltage-
controlled current:


( )
3
 K µ∗Vgk + V pk 2 for µ∗ Vgk + Vpk ≥ 0
Ip = 
0 for µ∗ Vgk + Vpk < 0

where

Ip
K=
( µ∗V )
3

gk + V pk 2

Other items are defined in “Triode Vacuum Tube Parameters and Defaults”.

Multisim 8 Component Reference Guide 11-5

Misc. Components

11.4.2 Model
The dynamic characteristic of the triode vacuum tube is modeled by its DC characteristic with
three capacitances (Cgk, Cpk, and Cgp) which are associated interelectrodes.

11.4.3 Triode Vacuum Tube Parameters and Defaults

Symbol Parameter name Default Unit

Vpk Plate-cathode voltage 250 V

Vgk Grid-cathode voltage -20 V

Ip Plate current 0.01 A

m Amplification factor 10 -

Cgk Grid-cathode capacitance 2e-12 F

Cpk Plate-cathode capacitance 2e-12 F

Cgp Grid-plate capacitance 2e-12 F

11.5 Voltage Reference

The output voltage of the Zener reference diode is set at approximately 6.9 V and requires a
high voltage supply. The band-gap voltage reference diode has a significant advantage over
the Zener reference diode in that it is capable of a lower minimum operating current and has a
sharper knee.
The band-gap reference relies on matched transistors and is therefore easily integrated along
with biasing, buffer and amplifier circuitry to give a complete reference diode.
The LM285/LM385 series are examples of micropower two-terminal band-gap voltage
reference diodes. These devices are designed to operate over a wide current range of 10 µA to
20 mA.

11-6 Electronics Workbench

 Voltage Regulator

The features of these devices include exceptionally low dynamic impedance, low noise, and
stable operation over time and temperature. The low operating current make these devices
suitable for micropower circuitry, such as portable instrumentation, regulators and other
analog circuitry that requires extended battery life.
Note Many types of two-terminal 1.2 V voltage reference diodes offer the same performance,
but are not all directly interchangeable. Minor differences in regulation voltage and in
allowable or required capacitive loading may affect a circuit.

11.6 Voltage Regulator

The linear IC voltage regulator is a device used to hold the output voltage from a dc power
supply relatively constant over a wide range of line and load variations. Most commonly used
IC voltage regulators are three-terminal devices.
There are four types of IC voltage regulators: fixed positive, fixed negative, adjustable, and
dual tracking. The fixed-positive and fixed-negative IC voltage regulators are designed to
provide specific output voltages. The adjustable regulator can be adjusted to provide any dc
output voltage within two specified limits. The dual-tracking regulator provides equal positive
and negative output voltages.
The regulator input-voltage polarity must match the device’s rated output polarity regardless
of the type of regulator used.
IC voltage regulators are series regulators, that is, they contain internal pass transistors and
transistor control components. The internal circuitry of an IC voltage regulator is similar to
that of the series feedback regulator.

Multisim 8 Component Reference Guide 11-7

Misc. Components

11.6.1 Input/Output Voltage Differential Rating

The input/output voltage differential rating shows the maximum difference between Vin and
Vout that can occur without damaging an IC voltage regulator.
The differential voltage rating can be used to determine the maximum allowable value of Vin
as follows:

V in ( max ) = V out ( adj ) + V d

where

Vin(max) = the maximum allowable unrectified dc input voltage

Vout(adj) = the adjusted output voltage of the regulator

Vd = the input/output voltage differential rating of the

regulator

11.7 Voltage Suppressor

The voltage suppressor diode is a Zener diode that is capable of handling high surges. It is
used as a filtering device to protect voltage-sensitive electronic devices from high energy
voltage transients.
The voltage suppressor diode is connected across the AC power input line to a DC power
supply. It contains two zener diodes that are connected back-to-back, making the voltage
suppressor diode bi-directional. This characteristic enables it to operate in either direction to
monitor under-voltage dips and over-voltage spikes of the AC input. It protects the power
supply from surges by shorting out any voltages greater than the Vz (Zener voltage) ratings of
the diodes.
The voltage suppressor diode must also have extremely high power dissipation ratings
because most AC power line surges contain a relatively high amount of power, in the
hundreds of watts or higher. It must also be able to turn on rapidly to prevent damage to the
power supply.

11-8 Electronics Workbench

 Boost Converter

In DC applications, a single unidirectional voltage suppressor can be used instead of a bi-

directional voltage suppressor. It is connected in shunt with the DC input and reverse biased
(cathode to positive DC).

11.8 Boost Converter

This component is an averaging circuit model that models the averaging behavior of a step-up
DC-to-DC switching converter. It is based on a unified behavioral model topology. The
topology models both small-signal and large-signal characteristics of this converter power
stage. The model can be used to simulate DC, AC and large-signal transient responses of
switched-mode power supplies operating in both the continuous and discontinuous inductor
current conduction modes (CCM and DCM, respectively).

11.8.1 Characteristic Equations

The averaging DC and large-signal characteristics of a Boost converter are given by the
following sets of equations:

Ii = ILL + ILD = IL
I0 = D2
D+ D2 ( ILL + ILD ) = DD+ D2 2 ∗ IL
in which ILL is governed by:

1 t
ILL =
L ∫0
[ D∗ Vi − D2 (V0 − Vi )]dt
where D = duty ratio of the switching device.

Multisim 8 Component Reference Guide 11-9

Misc. Components

For the DCM:

Vi
D2 = D∗
V 0 − Vi
Vl = 0
D( D + D2)
ILD = ∗Vi
2∗ L∗ Fs

For the critical condition between the CCM and the DCM of operations:
D2 = 1 − D
1
ILD = ILcrit = Vi∗ D∗
2∗ L∗ Fs

For the CCM:

D2 = 1 − D
VL = DiVi − D2 (V 0 − Vi )
IL = ILcrit + ILL
The averaging behavior governed by the above equations is modeled using the built-in
Multisim analog behavioral modeling components. The AC small-signal model is
automatically computed inside the program.

11.8.2 Boost Converter Parameters and Defaults

Symbol Parameter Name Default Unit

L Filter inductance 500 µH

R Filter inductor ESR 10 mΩ

Fs Switching frequency 50 kHz

11-10 Electronics Workbench

 Buck Converter

11.9 Buck Converter

This component is an averaging circuit model that models the averaging behavior of a step-
down DC-to-DC switching converter. It is based on a unified behavioral model topology. The
topology models both small-signal and large-signal characteristics of this converter power
stage. The model can be used to simulate DC, AC and large-signal transient responses of
switched-mode power supplies, operating in both the continuous and discontinuous inductor
current conduction modes (CCM and DCM, respectively).

11.9.1 Characteristic Equations

The averaging DC and large-signal characteristics of a Buck converter are given by the
following sets of equations:

D D
Ii = ∗ ( I LL + I LD ) = ∗ IL
D + D2 D + D2
I o = − ( I LL + I LD ) = − I L

in which ILL is governed by:

[ D(Vi − Vo ) − D2V0 ] dt
1 t
L ∫o
I LL =

where D = duty ratio of the switching device.

For the DCM:

Vi − V 0
D2 = D
V0
Vl = 0
D + D2
ILD = D(Vi − V 0)
2∗ L∗ Fs

Multisim 8 Component Reference Guide 11-11

Misc. Components

For the critical condition between the CCM and DCM of operation:

D2 = 1 − D
Vi − V0
I LD = I Lcrit =
2∗ L∗ Fs
For the CCM:

D2 = 1 − D
V L = D(Vi − V0 ) − D2 ∗Vo
I L = I Lcrit + I LL
The averaging behavior governed by the above equations is modeled using the built-in
Multisim analog behavioral modeling components. The AC small-signal model is
automatically computed inside the program.

11.9.2 Buck Converter Parameters and Defaults

Symbol Parameter Name Default Unit

L Filter inductance 500 µH

R Filter inductor ESR 5 mΩ

Fs Switching frequency 50 kHz

11.10 Buck Boost Converter

This component is an averaging circuit model that models the averaging behavior of a DC-to-
DC switching converter. It is based on a unified behavioral model topology. The topology
models both small-signal and large-signal characteristics of this converter power stage. This

11-12 Electronics Workbench

 Buck Boost Converter

behavioral model can be used to simulate DC, AC and large-signal transient responses of a
variety of switched-mode power supplies, operating in both the continuous and discontinuous
inductor current condition modes (DCM and CCM, respectively).

11.10.1Characteristic Equations

D D
Ii = ∗ ( I LL + I LD ) = ∗ IL
D + D2 D + D2
D2 D2
Io = ∗ ( I LL + I LD ) = ∗ IL
D + D2 D + D2
in which ILL is governed by:

[ D∗Vi − D2 ∗Vo ] dt
1 t
L ∫o
I LL =

where D = duty ratio of the switching devices.

For the DCM:

Vi
D2 = D
Vo
VL = 0
D∗Vi ( D + D2 )
I LD =
2∗ L∗ Fs

For the critical condition between the CCM and the DCM of operation:

D2 = 1 − D
D∗Vi
I LD = I Lcrit =
2∗ L∗ Fs

Multisim 8 Component Reference Guide 11-13

Misc. Components

For the CCM:

D2 = 1 − D
V L = D∗Vi − D2 ∗Vo
I L = I Lcrit + I LL
The averaging behavior governed by these equations is modeled using Multisim’s built-in
analog behavioral modeling components. The AC small-signal model is automatically
computed.

11.10.2Buck-Boost Converter Parameters and Defaults

Symbol Parameter Name Default Unit

L Filter inductance 500 µH

R Filter inductor ESR 5 mW

Fs Switching frequency 50 kHz

11.11 Fuse

This is a resistive component that protects against power surges and current overloads.
A fuse will blow (open) if the current in the circuit goes above Imax, the maximum current
rating. Imax can have any value from mA to kA.
The fuse is modeled by a resistor, R.

11-14 Electronics Workbench

 Lossy Transmission Line

11.11.1 Characteristic Equations

R =0 if i a ≤ I m ax
R =∞ if i a > I m ax

where

ia = current through the fuse, in amperes

Imax = maximum current rating of the fuse, in amperes.

For AC circuits, Imax is the peak value of the current, not its RMS value.

11.11.2 Fuse Parameters and Defaults

Symbol Parameter Name Default Unit

Imax Maximum current 1 A

11.12 Lossy Transmission Line

This component is a 2-port network that represents a medium, such as a wire or an

interconnect, through which electrical signals pass.
The lossy model also models resistive losses in the line along with the characteristic
impedance and propagation delay properties of the transmission line.
This is a two-part convolution model for single-conductor lossy transmission lines. The
uniform constant-parameter distributed transmission line model can be used to model the
following types of lines:
• RLC (uniform transmission lines with series loss only)

Multisim 8 Component Reference Guide 11-15

Misc. Components

• RC (uniform RC lines)
• LC (lossless transmission lines)
• RG (distributed series and parallel conductance).

11.12.1Model
The characteristic of a lossy transmission line is modeled by the Telegrapher Equations:

∂v ∂i
= − ( L + Ri )
∂x ∂t
∂i ∂v
= − (C + Gv )
∂x ∂t
with the following boundary and initial conditions:

v (0,t) = v1(t), v (l,t) = v2(t)

i (0,t) = i1(t), i (l,t) = -i2(t)
v (x,0) = v0(x), i (x,0) = i0(x)

where the transmission line stretches from x coordinates 0 to l

l = line length

V(x,t) = voltage at point x at time t

i (x,t) = current in the positive x direction at x at time t

v (0,t) = voltage at point 0 at time t

i (0,t) = current in the positive x direction at 0 at time t

v (x,0) = voltage at point x at time 0

i (x,0) = current in the positive x direction at x at time 0.

The set of equations is first transformed into a pair of coupled ordinary differential equations
in x and s using the Laplace transformation. The equations are then reformulated for
numerical convolution. Finally, inverse Laplace transforms are taken to return them to the
time-domain form.

11-16 Electronics Workbench

 Lossless Line Type 1

11.12.2Lossy Transmission Line Model Parameters and

Defaults

Symbol Parameter Name Default Unit

Len Length of the transmission line 100 m

Rt Resistance per unit length 0.1 Ω

Lt Inductance per unit length 1e-06 H

Ct Capacitance per unit length 1e-12 F

Gt Conductance per unit length 1e-12 mho

REL Breakpoint control 1 -

ABS Breakpoint control 1 -

Note A lossy transmission line with zero loss can be used to model the lossless transmission
line, and may be more accurate.

11.13 Lossless Line Type 1

This component is a 2-port network that represents a medium, such as a wire or an

interconnect, through which electrical signals pass.
The lossless model is an ideal one that simulates only the characteristic impedance and
propagation delay properties of the transmission line. The characteristic impedance is
resistive and is equal to the square-root of L/C.
Note A lossy transmission line with zero loss can be used to model the lossless transmission
line, and may be more accurate.

Multisim 8 Component Reference Guide 11-17

Misc. Components

11.13.1Model
A lossless transmission line is an LC model.
The values of L and C are given by:
td
ct = -----
Z

lt = td∗ Z

where

ct = capacitance per unit length

lt = inductance per unit length

td = propagation time delay

Z = nominal impedance

The propagation time-delay may be calculated from the data-books as follows:

 length 
td =  
 Vp 
Vp = Vf ∗ c
where

length = length of the line

Vp = velocity of propagation

Vf = velocity-factor

c = speed of light

11-18 Electronics Workbench

 Net

11.13.2Lossless Transmission Line Model Parameters

and Defaults

Symbol Parameter Name Default Unit

Z0 Nominal impedance 100 Ω

Td Propagation time delay 1e-09 s

11.13.3Lossless Line Type 2

This component is similar to lossless line type 1.

11.14 Net
This is a template for building a model. It allows you to input a netlist, using from 2 to 20
pins.

11.15 Filters

A number of filters are included that have symbols for layout purposes. These have footprint,
but no model information.

Multisim 8 Component Reference Guide 11-19

Misc. Components

11.16 Miscellaneous Components

The MISC family contains footprint information for a number of components, for example,
the Integrated GPS Receiver/Synthesizer shown here.
Model data is not provided.

11.17 PWM Controllers

This family contains footprint information for a number of components. Model data is not
provided.

11-20 Electronics Workbench

 Miscellaneous Power

11.18 Miscellaneous Power

This family contains footprint information for a number of components. Model data is not
provided.

11.19 Power Supply Controller

This family contains footprint information for a number of components. Model data is not
provided.

11.20 MOSFET Driver

This family contains footprint information for a number of components. Model data is not
provided.

11.21 Filters
This family contains footprint information for a number of components. Model data is not
provided.

Multisim 8 Component Reference Guide 11-21

Misc. Components

11-22 Electronics Workbench

Chapter 12
RF Components
RF components are not available in all editions of Multisim.

12.1 RF Capacitor

RF capacitors at RF frequencies show behaviors different from the regular capacitors at low
frequencies. RF capacitors at RF frequencies act as a combination of a number of
transmission lines, waveguides, discontinuities, and dielectrics. The dielectric layers are
usually very thin (typically 0.2 Mµm). The equations governing these types of capacitors
follow those of transmission lines; therefore, each RF capacitor is described by inductance per
unit length, resistance per unit length, shunt capacitance per unit length, and shunt
conductance per unit length. Depending on the type of the technology used, practical
capacitance values are in the range between several picofarads and several nanofarads. These
capacitors are used for coupling or bypassing for frequencies up to approximately 20 GHz.
One type of RF capacitor is called an interdigital capacitor. Both conductors of the capacitor
are in the same plane, which is the top surface of the dielectric substrate used. Each conductor,
or external node of the capacitor, is structured by connecting a number of transmission lines in
parallel. In other words, the planar structure uses N thin parallel conducting strips of length L,
linked alternately to one or other two strips of length W running perpendicularly alongside
them, and the whole structure is deposited on a substrate, often of alumina. Capacitors of this
type capacitors appear to be lumped up to 3 GHz and values from 0.1 to 10 pF can be
achieved. However, because of their structure, they require a relatively large area.

Multisim 8 Component Reference Guide 12-1

RF Components

12.2 RF Inductor

From many types of RF inductors, spiral inductors provide higher inductance values and
higher Qs. The spiral inductor is a technique of forming a planar inductor in a small place.
The shape is described by an increasing radius with angle: i.e. R = r/I + kθ
The equivalent circuit is a combination of series resistor (due to skin effect) and inductor, and
shunt capacitors (due to the distance between the surface which embraces the conductor, and
the ground plane). The quality of the inductor, usually noted as Q, is higher for spiral
inductors than those of other types of inductors, such as the rectangular spiral.

12.3 RF Bipolar Transistors

Basic operation of an RF bipolar transistor is identical to that of transistors designed for low
frequencies. RF transistors, however, have a higher maximum operating frequency (Wt),
depending on base and collector transit and charging times. To achieve this, the physical size
of emitter/base/collector areas at the layout level are minimized. However, reduction in the
base area is limited by the technology used to fabricate the transistor. Reduction in the
collector area is limited by the maximum tolerable voltage at the collector terminal. To
achieve maximum power output, the emitter periphery area should be as large as possible.
Because of these limitations, a special structure for bipolar transistors is used. This structure is
commonly referred to as an interdigital bipolar transistor.

12-2 Electronics Workbench

 RF MOS_3TDN

12.4 RF MOS_3TDN

RF FETs have a different type of carrier than bipolar transistors. Only the majority carriers
selected for FET should have better transport properties (such as high mobility, velocity,
diffusion coefficient). For this reason, RF FETs are fabricated on n-type materials since
electrons have better properties.
The two most important parameters are the gate length and width. A reduction in the gate
length will improve the gain, noise figure and frequency of operation. Increasing the gate
width will increase the RF power capability. That is why typical power FETs have multiple
gate fingers, interconnected via air bridges, with a total width of about 400 to 1000 µm.
The model parameters for RF FET transistors can be obtained using measured data for DC
and RF S-parameters. The equivalent circuit model should have almost identical DC and RF
S-parameters.

12.5 Tunnel Diode

A tunnel diode is a heavily doped diode that is used in high-frequency communications

circuits for applications such as amplifiers, oscillators, modulators, and demodulators. The
unique operating curve of the tunnel diode is a result of the heavy doping used in the
manufacturing of the diode. The tunnel diode is doped about one thousand times as heavily as
standard pn-junction diode.
The tunnel diode is different from any other diode because of its negative-resistance region. In
this area, forward voltage and current are inversely proportional. For example, an increase in
forward voltage would result in a reduction in diode current.
A tunnel diode can also be used to generate a sinusoidal voltage using a DC supply and a few
passive elements.

Multisim 8 Component Reference Guide 12-3

RF Components

12.6 Strip Line

Stripline is one of the most commonly used transmission lines at microwave frequencies.
Stripline is coined for ground-conductor-ground transmission line with a dielectric (normally
air) in between. Due to the multiplicity of the circuit functions, substrate, technologies, and
frequency bands, there is a wide range of stripline conductors. For example, microstrip lines
are a special type of stripline where the upper ground is placed at infinity. Depending on the
position of the stripline conductors, the shape of the conductor, and the thickness of the
conductor, the equations governing the behavior of one stripline to another differ. For
example, the centered stripline (often called Tri-Plate line), is a stripline where the
conductance is placed symmetrically in each position (from top, bottom, left, and right).
Another example is the Zero-Thickness stripline which is a very good approximation for
striplines in which the thickness of the conductor is negligible compared to the distance it has
from the ground planes.

12-4 Electronics Workbench

Chapter 13
Electromechanical Components

13.1 Switches

Switches can be closed or opened (turned on or off) by pressing a key on the keyboard. You
specify the key that controls the switch by typing its name in the Value tab of the component’s
Properties screen. For example, if you want the switch to close or open when the spacebar is
pressed, type space in the Value tab, then click OK.
A list of possible key names is shown below:

To use... Type

letters a to z the letter

(e.g. a)

Enter enter

spacebar space

Multisim 8 Component Reference Guide 13-1

Electromechanical Components

13.2 Supplementary Contacts

This component Family contains a variety of electromechanical switches.

13.3 Momentary Switches

Press the switch’s key during simulation to make the switch toggle positions.

13.4 Line Transformer

Line Transformers are simplified transformers intended for power applications where the
primary coils is connected to either 120 or 220 VAC. They will perform step up or step down
functions plus several specialized functions of voltage and current measurement.

13-2 Electronics Workbench

 Coils, Relays

13.5 Coils, Relays

Multisim includes the following coils and relays:

• motor starter coil
• forward or fast starter coil
• reverse starter coil
• slow starter coil
• control relay
• time delay relay.

13.6 Timed Contacts

Multisim includes the following timed contacts:

• normally open timed closed
• normally open timed closed.

Multisim 8 Component Reference Guide 13-3

Electromechanical Components

13.7 Protection Devices

Multisim includes the following protection devices

• fuse
• overload
• overload thermal
• overload magnetic
• ladder logic overload

13.8 Output Devices

Multisim includes the following output devices:

• light indicator
• motor
• DC motor armature
• 3 phase motor
• heater
• LED indicator
• solenoid.

13-4 Electronics Workbench

 Push Buttons

13.9 Push Buttons

Multisim includes the following push button switches:
• N.O.
• N.C.
• N.O. & N.C. (double circuit)
• mushroom head
• wobble stick
• illuminated.
Push button switches are momentary switches which need to be activated only for the
duration during which the user manually acts on them.

13.10 Pilot Lights

Multisim includes the following pilot lights:
• non push-to-test
• push-to-test.

13.11 Terminals
Multisim includes the following terminals:
• power terminals
• control terminals N.O.
• control terminals N.C.
• coil terminals.

Multisim 8 Component Reference Guide 13-5

Electromechanical Components

13-6 Electronics Workbench

Index
Numerics 4-bit Bistable Latches
10-to-4 Priority Enc 6-17 74xx375 6-64
74xx75 6-86
12-In NAND w/3-state Out 6-13
74xx77 6-87
12-stage Binary Counter 7-33
4-bit Cascadable Shift Reg w/3-state Out 6-69
13-In NAND 6-13
4-bit Comparator 7-69
13-input Checker/Generator 7-62
4-bit Dec Counter
14-stage Bin Counter 7-21 40160 7-11
1-of-10 Dec 7-26 40162 7-13
1-of-16 Data Sel/MUX 6-18 40192 7-19
1-of-16 Dec/DEMUX w/Input latches 4-bit D-type Reg w/3-state Out 6-30
4514 7-57 4-bit Mag COMP 6-94
4515 7-58 4-bit Parallel-Access Shift Reg 6-38
1-of-8 Data Sel/MUX 6-19 4-bit Shift Register
2-bit Bin Full Adder 6-89 40194 7-20
2-wide 4-In AND-OR-INVERTER 6-82 40195 7-20
3 3-Input AND 6-18 4035 7-29
3-to-8 Dec 6-14 4-bit Shifter w/3-state Out 6-58
3-to-8 line Dec/DEMUX 6-42 4-to-16 Dec/DEMUX 6-20
4000 series functions See functions 4-to-16 Dec/DEMUX (OC) 6-23
4000 series ICs 7-2 4-Wide 2-In AND-OR-INVERTER 7-49
4-BCD to 10-Decimal Dec 6-70 4-wide AND-OR-INVERTER 6-81
4-bit BCD Down Counter 7-61 5-stage Johnson Counter
4-bit Bidirect Univ. Shift Reg 6-38 4017 7-14
4018 7-17
4-bit Bin Counter 7-13
40161 7-12 74xx series functions See functions
40193 7-19 7-stage Binary Counter 7-23
4-bit Bin Down Counter 7-61 8-Bit Bist Latch 6-7
4-bit Bin Full Add 6-55 8-bit Latch
4-bit Bin Full Adder 6-93 4099 7-51
74xx259 6-52
4-bit Bin/BCD Dec Counter 7-27
8-bit Parallel-Out Serial Shift Reg 6-28
4-bit Binary Counter
74xx293 6-56 8-bit Priority Enc 7-63
74xx93 6-97 8-bit Shift Reg 6-95
4-bit Binary Full Adder 7-5 8-bit Shift Reg (sh/ld ctrl) 6-40

Multisim 8 Component Reference Guide i

8-bit Shift Reg (shl/shr ctrl) 6-39 junction transistors) 4-1
8-bit Static Shift Reg 7-9 BJT arrays (see also BJT arrays) 4-10
8-bit Static Shift Register 7-21 comparator 5-9
Darlington connection (see also Darlington
8-In MUX w/3-state Out 7-55
connection) 4-8
8-In NAND diac (see also diac) 3-14
4068 7-38 diodes (see also diodes) 3-1
74xx30 6-57 DMOS transistor 4-21
8-In NOR 7-44 full-wave bridge rectifier (see also full-wave
8-stage Serial Shift Register 7-50 bridge rectifier) 3-10
8-to-3 Priority Enc 6-17 GaAsFET (see also GaAsFET) 4-21
9-bit Odd/even Par GEN 6-31 IGBT-IGBT 4-23
LED (Light-Emitting Diode) (see also LED)
9-bit odd/even parity generator/checker 6-55
3-8
MOSFET (see also MOSFET) 4-12
A Norton opamps 5-8
AC current source 1-5 opamps (see also opamps) 5-1
AC frequency model optocoupler 11-4
capacitors 2-7 PIN diode 3-5
inductors 2-10 Schottky diode 3-12
AC model 4-9 SCR (Silicon-Controlled Rectifier) (see also
SCR) 3-12
AC small-signal model
triac 3-16
bipolar junction transistors 4-5
triode vacuum tube (see also triode vacuum
diac 3-15
tube) 11-5
diodes 3-4
varactor diode 3-18
MOSFET 4-14
voltage reference 11-6
SCR 3-14
voltage regulator 11-7
AC voltage source 1-4 voltage suppressor 11-8
ADC DAC 9-1 voltage-controlled analog 9-2
Alu/Function Generator 6-32 wide bandwith amplifiers 5-11
AM source. See amplitude modulation source zener diode (see also zener diode) 3-6
ammeter analog switch 9-2
about 10-2 AND-gated JK MS-SLV FF (pre, clr) 6-84
connecting 10-2 AND-OR-INVERTER 6-79
mode 10-2 arrays, BJT 4-10
resistance 10-2
amplifiers, wide bandwidth 5-11
B
amplitude modulation source 1-5
bargraph, about 10-7
analog components
battery 1-2
bipolar junction transistors (see also bipolar

ii Electronics Workbench
BCD up/down Counter 7-53 C
BCD-to-Decimal Dec capacitor virtual 2-8
74xx145 6-16 capacitors
74xx445 6-73 about 2-5
74xx45 6-74 AC frequency model 2-7
BCD-to-seven segment dec DC model 2-6
74xx246 6-44 equations 2-6
74xx247 6-45 RF 12-1
74xx248 6-46 time-domain model 2-6
74xx249 6-48 clock 1-9
74xx46 6-74
coil, types of 13-3
74xx47 6-76
74xx48 6-78 comparator
about 5-9
BCD-to-seven segment latch/dec
parameters and defaults 5-11
4511 7-54
4544 7-66 COMS components
TinyLogic_2V 7-70
BCD-to-seven segment latch/dec/driver 7-64
connecting
Binary up/down Counter 7-59
ammeter 10-2
bipolar junction transistors voltmeter 10-2
about 4-1
connectors 2-1
AC small-signal model 4-5
characteristic equations 4-2 control functions
parameters and defaults 4-6 current limiter block (see also current limiter
time-domain model 4-4 block) 1-45
differentiator (see also differentiator) 1-38
BJT arrays
divider (see also divider) 1-31
about 4-10
integrator (see also integrator) 1-40
general-purpose high-current N-P-N
limiter (see also limiter) 1-44
transistor array 4-11
multiplier (see also multiplier) 1-29
general-purpose P-N-P transistor array 4-
three-way summer 1-52
10
transfer function block (see also transfer
N-P-N/P-N-P transistor array 4-11
function block) 1-34
BJT. See bipolar junction transistors voltage gain block
BJT_NRES 4-8 voltage hysteresis block 1-42
boost converter 11-9 voltage slew rate block 1-50
buck boost converter 11-12 voltage-controlled limiter 1-48
buck converter 11-11 controlled one-shot 1-27
buzzer, about 10-8 coreless coil 2-20
crystal 11-1
current limiter block

Multisim 8 Component Reference Guide iii

 about 1-45 digital ground 1-2
parameters and defaults 1-47 diodes 3-1
current-controlled current source 1-10 AC small-signal model 3-4
current-controlled voltage source 1-9 DC model 3-2
customizing parameters and defaults 3-4
nonlinear transformer 2-12 time-domain model 3-3
Divide-by-twelve Counter 6-96
D divider
about 1-31
Darlington connection
equations 1-33
about 4-8
parameters and defaults 1-33
AC model 4-9
DC bias model 4-9 DMOS transistor 4-21
Data Sel/MUX 6-19 Dual 1-of-4 Dec/DEMUX
4555 7-67
Data Sel/MUX w/3-state Out 6-49
4556 7-68
DC bias model 4-9
Dual 2-to-4 Dec/DEMUX
DC current source 1-4 74xx139 6-15
DC model 74xx155 6-21
capacitors 2-6 Dual 2-to-4 Dec/DEMUX (OC) 6-22
diac 3-15
Dual 2-Wide 2-In AND-OR-INVERTER 7-47
diodes 3-2
inductors 2-9 Dual 3-In NOR and INVERTER 7-3
MOSFET 4-13 Dual 4-bit Binary Counter
zener diode 3-6 74xx393 6-68
DC voltage source 1-2 74xx69 6-84
Decade Counter 6-55, 6-95 Dual 4-bit latch 7-52
depletion MOSFET 4-12 Dual 4-bit latches (clr) 6-11
diac Dual 4-bit Static Shift Reg 7-10
about 3-14 Dual 4-In AND
AC small-signal model 3-15 4082 7-46
DC model 3-15 74xx21 6-41
parameters and defaults 3-16 Dual 4-In NAND
time-domain model 3-15 4012 7-7
differentiator 74xx20 6-41
about 1-38 74xx40 6-69
equations 1-40 Dual 4-In NAND (OC) 6-42
parameters and defaults 1-40 Dual 4-In NOR 7-4
sine wave 1-38 Dual 4-In NOR w/Strobe 6-49
square wave 1-39
Dual 4-In OR 7-40
triangle waveform 1-38

iv Electronics Workbench
Dual 4-input Multiplexer 7-64 multiplier 1-31
Dual 4-to-1 Data Sel/MUX relay 2-15
74xx153 6-20 resistors 2-4
74xx352 6-59 three-way summer 1-53
Dual 4-to-1 Data Sel/MUX w/3-state Out transfer function block 1-34
74xx253 6-50 triode vacuum tube 11-5
74xx353 6-60 voltage gain block 1-37
Dual BCD Counter 7-59 Exc-3-Gray-to-Decimal Dec 6-72
Dual Binary Counter 7-60 Exc-3-to-Decimal Dec 6-71
Dual Com Pair/Inv 7-4 exp. current source 1-26
Dual Data Sel/MUX w/3-state Out 6-59 exp. voltage source 1-24
Dual Div-by-2, Div-by-5 Counter 6-66
Dual D-type FF F
(+edge) 7-8 FM source. See frequency modulated source
(pre, clr) 6-85 frequency modulated source 1-6
Dual JK FF frequency shift key modulated source 1-8
(+edge, pre, clr) 4027 7-25 FSK source. See frequency shift key modulated
(+edge, pre, clr) 74xx109 6-8 source
(clr) 74xx107 6-7 full-wave bridge rectifier
(clr) 74xx73 6-85 about 3-10
(-edge, pre, clr) 6-9 characteristic equation 3-10
(-edge, pre, com clk & clr) 6-10 model 3-10
(pre, clr) 6-86 parameters and defaults 3-11
(pre, com clk & clr) 6-87
functions
Dual JK MS-SLV FF (-edge, pre) 6-10 4000 7-3
4001 7-3
E 4002 7-4
enhancement MOSFET 4-12 4007 7-4
equations 4008 7-5
bipolar junction transistors 4-2 4010 7-6
capacitors 2-6 40106 7-6
differentiator 1-40 4011 7-7
divider 1-33 4012 7-7
full-wave bridge rectifier 3-10 4013 7-8
GaAsFET 4-22 4014 7-9
inductors 2-9 4015 7-10
integrator 1-41 40160 7-11
limiter 1-45 40161 7-12
linear transformer 2-11 40162 7-13
40163 7-13

Multisim 8 Component Reference Guide v

 4017 7-14 4077 7-43
40174 7-15 4078 7-44
40175 7-16 4081 7-45
4018 7-17 4082 7-46
4019 7-18 4085 7-47
40192 7-19 4086 7-49
40193 7-19 4093 7-49
40194 7-20 4094 7-50
40195 7-20 4099 7-51
4020 7-21 4502 7-51
4021 7-21 4503 7-52
4023 7-22 4508 7-52
4024 7-23 4510 7-53
40240 7-23 4511 7-54
40244 7-24 4512 7-55
40245 7-24 4514 7-57
4025 7-24 4515 7-58
4027 7-25 4516 7-59
4028 7-26 4518 7-59
4029 7-27 4519 7-60
4030 7-28 4520 7-60
4032 7-29 4522 7-61
4035 7-29 4526 7-61
40373 7-31 4531 7-62
40374 7-32 4532 7-63
4038 7-32 4539 7-64
4040 7-33 4543 7-64
4041 7-33 4544 7-66
4042 7-34 4555 7-67
4043 7-35 4556 7-68
4044 7-35 4585 7-69
4049 7-36 74xx00 6-2
4050 7-36 74xx01 6-3
4066 7-37 74xx02 6-3
4068 7-38 74xx03 6-3
4069 7-38 74xx04 6-4
4070 7-39 74xx05 6-4
4071 7-39 74xx06 6-5
4072 7-40 74xx07 6-5
4073 7-41 74xx08 6-5
4075 7-42 74xx09 6-6
4076 7-43 74xx10 6-6

vi Electronics Workbench
 74xx100 6-7 74xx17 6-30
74xx107 6-7 74xx173 6-30
74xx109 6-8 74xx174 6-30
74xx11 6-8 74xx175 6-31
74xx112 6-9 74xx180 6-31
74xx113 6-10 74xx181 6-32
74xx114 6-10 74xx182 6-33
74xx116 6-11 74xx190 6-35
74xx12 6-11 74xx191 6-36
74xx125 6-12 74xx192 6-36
74xx126 6-12 74xx193 6-37
74xx132 6-13 74xx194 6-38
74xx133 6-13 74xx195 6-38
74xx134 6-13 74xx198 6-39
74xx135 6-14 74xx199 6-40
74xx136 6-14 74xx20 6-41
74xx138 6-14 74xx21 6-41
74xx139 6-15 74xx22 6-42
74xx14 6-15 74xx238 6-42
74xx145 6-16 74xx240 6-43
74xx147 6-17 74xx241 6-43
74xx148 6-17 74xx244 6-43
74xx15 6-18 74xx246 6-44
74xx150 6-18 74xx247 6-45
74xx151 6-19 74xx248 6-46
74xx152 6-19 74xx249 6-48
74xx153 6-20 74xx25 6-49
74xx154 6-20 74xx251 6-49
74xx155 6-21 74xx253 6-50
74xx156 6-22 74xx257 6-51
74xx157 6-22 74xx258 6-51
74xx158 6-23 74xx259 6-52
74xx159 6-23 74xx26 6-52
74xx16 6-24 74xx266 6-52
74xx160 6-25 74xx27 6-53
74xx161 6-25 74xx273 6-54
74xx162 6-26 74xx279 6-54
74xx163 6-27 74xx28 6-54
74xx164 6-28 74xx280 6-55
74xx165 6-28 74xx283 6-55
74xx166 6-29 74xx290 6-55
74xx169 6-29 74xx293 6-56

Multisim 8 Component Reference Guide vii

 74xx298 6-56 74xx75 6-86
74xx30 6-57 74xx76 6-86
74xx32 6-57 74xx77 6-87
74xx33 6-58 74xx78 6-87
74xx350 6-58 74xx82 6-89
74xx351 6-59 74xx83 6-93
74xx352 6-59 74xx85 6-94
74xx353 6-60 74xx86 6-94
74xx365 6-60 74xx90 6-95
74xx366 6-61 74xx91 6-95
74xx367 6-61 74xx92 6-96
74xx368 6-62 74xx93 6-97
74xx37 6-62 fuse 11-14
74xx373 6-63
74xx374 6-63
G
74xx375 6-64
74xx377 6-64 GaAsFET
74xx378 6-65 about 4-21
74xx379 6-65 equations 4-22
74xx38 6-65 parameters and defaults 4-23
74xx39 6-66 gain. See voltage gain block
74xx390 6-66 gaussian white noise 1-55
74xx393 6-68 general-purpose high-current N-P-N transistor
74xx395 6-69 array 4-11
74xx40 6-69 general-purpose P-N-P transistor array 4-10
74xx42 6-70
generator
74xx43 6-71
sine wave 1-11
74xx44 6-72
square wave 1-9
74xx445 6-73
triangle wave 1-15
74xx45 6-74
74xx46 6-74 ground 1-1
74xx465 6-76
74xx466 6-76 H
74xx47 6-76 Hex BUFFER
74xx48 6-78 4010 7-6
74xx51 6-79 4050 7-36
74xx54 6-81 Hex BUFFER (OC)
74xx55 6-82 74xx07 6-5
74xx69 6-84 74xx17 6-30
74xx72 6-84
Hex Buffer/Driver w/3-state
74xx73 6-85
74xx365 6-60
74xx74 6-85

viii Electronics Workbench

 74xx367 6-61 instruments
hex display ammeter 10-2
about 10-4 bargraph 10-7
Hex D-type buzzer 10-8
Flip-flop 7-15 hex display 10-4
lamp 10-3
Hex D-type FF
probe 10-3
(clr) 6-30
voltmeter 10-1
w/en 6-65
integrator
Hex INVERTER
about 1-40
(OC) 74xx05 6-4
equations 1-41
(OC) 74xx16 6-24
parameters and defaults 1-42
(Schmitt) 40106 7-6
(Schmitt) 74xx14 6-15
4049 7-36 J
4069 7-38 JFET_N 4-18
74xx04 6-4 johnson noise 1-55
Buffer/Driver w/3-state, 74xx366 6-61
Buffer/Driver w/3-state, 74xx368 6-62
L
Hex INVERTER (OC) 6-5
lamp
hysteresis block about 10-3
about 1-42
LED
parameters and defaults 1-43
about 3-8
parameters and defaults 3-9
I limiter
IBEW components about 1-44
coils 13-3 equations 1-45
output devices 13-4 parameters and defaults 1-45
pilot lights 13-5 line transformer 13-2
protection devices 13-4
linear transformer
relays 13-3
about 2-11
switches 2-2
equations 2-11
timed contacts 13-3
parameters and defaults 2-12
IGBT-IGBT 4-23
Look-ahead Carry GEN 6-33
inductor virtual 2-10
lossless line type 1 11-17
inductors
lossless line type 2 11-19
about 2-8
AC frequency model 2-10 Lossless transmission line
DC model 2-9 parameters and default values 11-19
equations 2-9 lossy transmission line 11-15
time-domain model 2-9

Multisim 8 Component Reference Guide ix

M customizing 2-12
magnetic core 2-19 parameters and defaults 2-13
magnetic relay 2-14 Norton opamps 5-8
misc. digital components N-P-N/P-N-P transistor array 4-11
line driver 8-12
line receiver 8-12 O
line transceiver 8-13 Octal BUFFER w/3-state Out 6-43
VHDL 8-10 74xx240 6-43
mode 74xx244 6-43
ammeter 10-2 74xx465 6-76
voltmeter 10-1 74xx466 6-76
model Octal Bus Transceiver 7-24
full-wave bridge rectifier 3-10 Octal D-type
relay 2-14 FF 6-54
SCR 3-13 FF (+edge) 6-63
triode vacuum tube 11-6 FF w/en 6-64
model parameters Flip-flop 7-32
opamps 5-1 Transparent Latches 6-63
mono stable 9-4 Octal Inv Buffer 7-23
MOSFET Octal Non-inv Buffer 7-24
about 4-12 Octal Trans Latch 7-31
AC small-signal model 4-14 opamps
DC model 4-13 3-terminal
depletion 4-12 about 5-3
enhancement 4-12 5-terminal
parameters and defaults 4-15 interstage 5-7
time-domain model 4-14 output stage 5-7
motor 11-2 about 5-1
multiplier ideal model 5-1
about 1-29 model parameters 5-1
equations 1-31 optocoupler 11-4
parameters and defaults 1-31 oscillator
Multivibrators 9-6 voltage-controlled sine wave 1-11
voltage-controlled square wave 1-13
N voltage-controlled triangle wave 1-15
net 11-19 output device, types of 13-4
nonlinear dependent source 1-26
nonlinear transformer P
about 2-12 Parallel-load 8-bit Shift Reg

x Electronics Workbench
 74xx165 6-28 pilot light, types of 13-5
74xx166 6-29 PIN diode 3-5
parameters and defaults PLL 9-4
bipolar junction transistors 4-6 polynomial source 1-23
comparator 5-11
potentiometer 1-11, 2-17
current limiter block 1-47
diac 3-16 probe
differentiator 1-40 about 10-3
diodes 3-4 protection device, types of 13-4
divider 1-33 pullup 2-18
full-wave bridge rectifier 3-11 pulse current source 1-23
GaAsFET 4-23 pulse voltage source 1-21
integrator 1-42
push button switch 13-5
LED 3-9
limiter 1-45 PWL source. See piecewise linear source
linear transformer 2-12
MOSFET 4-15 Q
multipliers 1-31 Quad 2-In AND
nonlinear transformer 2-13 (OC) 74xx09 6-6
opamps 5-1 4081 7-45
SCR 3-14 74xx08 6-5
three-way summer 1-54 Quad 2-in Exc-OR gate 6-14
transfer function block 1-35
Quad 2-In MUX 6-56, 7-18
triode vacuum tube 11-6
voltage gain block 1-37 Quad 2-In NAND
voltage hysteresis block 1-43 (Ls-OC) 74xx03 6-3
voltage slew rate block 1-51 (OC) 74xx26 6-52
voltage-controlled limiter 1-49 (OC) 74xx38 6-65
zener diode 3-7 (OC) 74xx39 6-66
(Schmitt) 4093 7-49
passive components
(Schmitt) 74xx132 6-13
capacitors (see also capacitors) 2-5
4011 7-7
crystal 11-1
74xx00 6-2
inductors (see also inductors) 2-8
74xx01 6-3
linear transformer (see also linear
74xx37 6-62
transformer) 2-11
nonlinear transformer (see also nonlinear Quad 2-In NOR
transformer) 2-12 (OC) 74xx33 6-58
relay (see also relay) 2-14 4001 7-3
resistors (see also resistors) 2-3 74xx02 6-3
74xx28 6-54
piecewise linear current source 1-21
Quad 2-In OR
piecewise linear voltage source 1-18
4071 7-39

Multisim 8 Component Reference Guide xi

 74xx32 6-57 virtual 2-5
Quad 2-In XNOR RF BJT_NPN 12-2
(OC) 74xx266 6-52 RF capacitor 12-1
4077 7-43 RF inductor 12-2
Quad 2-In XOR RF MOS_3TDN 12-3
4030 7-28
rpack 2-18
4070 7-39
74xx86 6-94
Quad 2-to-1 Data Sel/MUX 6-22, 6-23 S
Quad 2-to-1 line Data Sel/MUX Schottky diode 3-12
74xx257 6-51 SCR
74xx258 6-51 about 3-12
Quad Analog Switches 7-37 AC small-signal model 3-14
model 3-13
Quad bus BUFFER w/3-state Out 6-12
parameters and defaults 3-14
Quad D-latch 7-34 time-domain model 3-13
Quad D-type sensing switches 13-1
FF (clr) 6-31
sine wave 1-38
FF w/en 6-65
Flip-flop 7-16 sine wave generator 1-11
Reg w/3-state Out 7-43 source
Quad Ex-OR/NOR Gate 6-14 AC current 1-5
AC voltage 1-4
Quad Multiplexer 7-60
amplitude modulation 1-5
Quad RS latch w/3-state Out 7-35 current-controlled current 1-10
Quad SR latches 6-54 current-controlled voltage 1-9
Quad True/Complement BUFFER 7-33 DC current 1-4
DC voltage 1-2
R exp. current 1-26
exp. voltage 1-24
relay
frequency modulated 1-6
about 2-14
frequency shift key modulated 1-8
equations 2-15
nonlinear dependent 1-26
model 2-14
piecewise linear current 1-21
types of 13-3
piecewise linear voltage source 1-18
resistance polynomial 1-23
about 2-4 pulse current 1-23
ammeter 10-2 pulse voltage 1-21
voltmeter 10-1 Vcc voltage 1-3
resistors voltage-controlled current 1-10
about 2-3 voltage-controlled piecewise linear 1-16
equations 2-4 voltage-controlled voltage 1-9

xii Electronics Workbench

square wave 1-39 transformer
square wave generator 1-9 linear 2-11
strip line 12-4 nonlinear 2-12
Strobed hex INVERTER 7-51 Tri 3-In AND
4073 7-41
summer, three-way 1-52
74xx11 6-8
switch
Tri 3-In NAND
push button 13-5
(OC) 74xx12 6-11
types of 2-2
4023 7-22
Sync 4-bit Bin Counter 6-25 74xx10 6-6
Sync 4-bit Bin Up/down Counter 6-37 Tri 3-In NOR
Sync 4-bit Binary Counter 6-27 4025 7-24
Sync 4-bit Decade Counter 6-26 74xx27 6-53
Sync 4-bit Decade Counter (clr) 6-25 Tri 3-In OR 7-42
Sync 4-bit up/down Binary Counter 6-29 triac 3-16
Sync 4-bit up/down Counter 6-36 triangle wave generator 1-15
Sync BCD Up/down Counter 6-35, 6-36 triangle waveform 1-38
triode vacuum tube
T about 11-5
terminal, types of 13-5 equations 11-5
model 11-6
thermal noise 1-55
parameters and defaults 11-6
three-way summer
Triple Serial Adder
about 1-52
4032 7-29
equations 1-53
4038 7-32
parameters and defaults 1-54
Tri-state hex BUFFER w/Strobe 7-52
timed contact, types of 13-3
TTL components 6-1
time-domain model
bipolar junction transistors 4-4 tunnel diode 12-3
capacitors 2-6
diac 3-15 V
diodes 3-3 varactor diode 3-18
inductors 2-9 variable capacitor 2-15
MOSFET 4-14
variable inductor 2-16
SCR 3-13
Vcc voltage source 1-3
timer 9-3
voltage
transfer function block
gain 1-9
about 1-34
equations 1-34 voltage differentiator. See differentiator
parameters and defaults 1-35 voltage gain block

Multisim 8 Component Reference Guide xiii

 about 1-36 parameters and defaults 3-7
equations 1-37
parameters and defaults 1-37
voltage hysteresis block
about 1-42
parameters and defaults 1-43
voltage integrator. See integrator
voltage limiter. See limiter
voltage reference 11-6
voltage regulator 11-7
voltage slew rate block
about 1-50
parameters and defaults 1-51
voltage suppressor 11-8
voltage-controlled analog 9-2
voltage-controlled current source 1-10
voltage-controlled limiter
about 1-48
parameters and defaults 1-49
voltage-controlled piecewise linear source 1-16
voltage-controlled sine wave oscillator 1-11
voltage-controlled square wave oscillator 1-13
voltage-controlled triangle wave oscillator 1-15
voltage-controlled voltage source 1-9
voltmeter
about 10-1
connecting 10-2
mode 10-1
resistance 10-1

W
white noise 1-55
wide bandwidth amplifiers 5-11

Z
zener diode
about 3-6
DC model 3-6

xiv Electronics Workbench