Chap 7 Components of Optical Instruments - III

Components of Optical Instruments
Chapter 7_III UV, Visible and IR Instruments
Grating Monochromators
Principle of operation: Diffraction Diffraction sources: grooves on a reflecting surface Fabrication: Master Grating is mechanically ruled on a flat polished surface with a diamond, to produce identical closely spaced parallel grooves Replica grating: are cast using 'liquid plastic'. Then they are coated with a reflecting material
Echellette Grating
The grating is blazed/ grooved to produce broad faces used for reflection and narrow unused faces. How does it work?
Maximum constructive Interference between two beams originating from two adjacent faces occurs when the difference in path travelled is equal to one wavelength or an integral multiple of the wavelength. Different wavelengths are diffracted at different angles.
n = CB + BD CB = d sin i CAB = i BD = d sin r DAB = r
n = d (sin i + sin r )
Holographic grating: two laser beams are focused on a photosensitive surface to create grooves Concave Gratings Lines ruled on a concave spherical mirror Do not need internal collimating and focusing optics Typical sizes: 1- 10 cm, 300 to 2000 grooves/mm
Performance Characteristics
Dispersion
Determines the ability of a monochromator to separate different wavelengths
Angular dispersion
dr n = d d cos r
Linear dispersion
D= dy fdr = d d d 1 d d cos r = = dy f dr nf
if r is small < 20
D 1 =
D 1 =
d nf
Resolving Power
Determines the limit of the ability to separate adjacent images that have a slight difference in wavelength Better for longer gratings, smaller d, higher n
R=
R = nN N : number of grooves
Light Gathering Power

Determines the ability of the monochromator to collect radiation from the entrance slit F-number F, speed
F=
f d
f : focallength of mirror orlens of mirror orlens d : diameter
Echelle grating
Two dispersing elements in series Echelle grating + low resolution prism or grating ir=6326
n = 2d sin
D 1 = d cos nf
C-3 Monochromators Slits

Entrance and Exit slit
Rectangular images of the entrance slit are produced on the focal plane that contains the exit slit
Effect of Slit Width on Resolution

Bandwidth: span of monochromator settings (in units of wavelenght or cm-1) needed to move the image of the entrance slit across the exit slit Effective bandwidth (eff) (spectral bandpass or spectral slit) is the range of wavelengths at the exit slit at a given monochromator setting. Is equal to half the bandwidth when the two slits are equal.
D 1 =
eff = wD 1 w : slit width
Effect of Slit Width on Resolution
Equal to the difference in wavelengths
E. Radiation Transducers
E-1 Introduction
Early detectors in Spectroscopy
Human eye Photographic plates Films
Properties of an Ideal Transducer

High sensitivity High signal to noise ratio Constant response over a wide range of wavelengths Fast response Response directly proportional to radiant power Low dark current
S = kP S = kP + k d
General Classification of Transducers Photon transducers: photoelectric / quantum detectors

Photoemissive: Photon emission of electrons photocurrent Photoconductive: Photon electron to CB enhanced conductivity Used in UV, Vis and near IR
Heat transducers
Average radiant powerthermal conduction Mainly used in the IR region
E-2 Photon Transducers E-2-1 Vaccum Phototubes

Photoelectric effect Photoemissive surfaces Operational Amplifier
Photoemissive surfaces Bialkali: most sensitive

K/Cs/Sb (117)
Red-sensitive:
Ag/O/Cs (S-11):
Flatresponse
Ga/As (128): flat response
E-2-2 Photomultiplier Tubes

Components
Photocathode surface Dynodes: maintained at increasing potential relative to cathode Anode Operational Amplifier (OP AMP)
Nature of signal from a PMT

a series of charge packets may have 106 electrons and be 5 ns wide Output is a current Very sensitive in UV and vis Fast response
10 6 anode . pulses electrons coulomb coulombs 10 6 1.6 10 19 = 1.6 10 7 anode . pulse electron sec sec
Dark Current in Photomultipliers

Sensitivity limited by dark current Origin of dark current (output signal when no light is present) Thermal emission*: spontaneous emission of electrons Cold-Field Emission: spontaneous emission due to sharp surfaces/edges in the presence of high electrical field Radioactivity Ohmic leakage: resistance in the tube will cause an IR drop , thus flow of current
Silicon Photodiode Transducers

Reverse-biased pn junction on a silicon chip ER generates holes and electrons in depletion layer Less sensitive than photomultiplier Spectral region (190 1100 nm)
E-3 Multichannel Photon Transducers Allows the simultaneous detection of all resolution elements of the spectrum Types
Photodiode arrays (PDA)
Common number of diodes: 1024
Charge-Transfer Devices (CTDs)
E-4 Photoconductivity Transducers

Used in the near IR region (0.75 m - 3 m). Semiconductors whose resistance decreases when they absorb radiation of wavelength between 0.75 m and 3 m. Change in conductivity is measured. Sulfides, Selenides, Stibnides of lead, cadmium, gallium and indium.
10
E-5 Thermal Transducers

Operational principle:
IR radiation raises temperature of a black body with low heat capacity. Temperature increase is a measure of radiant power. Typical radiant power in IR: 10-7 to 10-9 W. Typical temperature changes: order of 0.001 K.
Problem: thermal noise (thermal radiation emitted by other surfaces).

Housing of detector must be evacuated and shielded from thermal radiation from other surfaces
Examples of Thermal Transducers

THERMOCOUPLES
Couple: two identical pieces of metal connected by a dissimilar metal e.g. Bi and Sb Potential difference will develop at the junction due to differences in temperature.
BOLOMETERS (Thermistors)
Resistance thermometer made of Pt, Ni or semiconductors. Principle of operation: large change in resistance as a function of temperature
PYROELECTRIC TRANSDUCERS
Used in FT IR, which requires fast response Pyroelectric materials: dielectric material with a long lived polarized state. Principle of operation: temperature dependence of polarization in absence of electrical field is a measure of radiant power. IR temperature changecharges distribution changemesurable current in the external circuit. Pyroelectric material: Triglycine sulfate (NH2CH2COOH)3.H2SO4.
11
G. Fiber Optics
Fine strands of glass or plastic Diameter: 0.05 m-0.6 cm Transmits Radiation over long distances Used for transmitting images (medicine) and for illumination Operational Principle Total Internal Reflection
12

Chap 7 Components of Optical Instruments - III

Uploaded by

Copyright:

Available Formats

Chap 7 Components of Optical Instruments - III

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Chap 7 Components of Optical Instruments - III

Uploaded by

Copyright:

Available Formats

Components of Optical Instruments

Chapter 7_III UV, Visible and IR Instruments

n = CB + BD CB = d sin i CAB = i BD = d sin r DAB = r

Light Gathering Power

f : focallength of mirror orlens of mirror orlens d : diameter

C-3 Monochromators Slits

Effect of Slit Width on Resolution

eff = wD 1 w : slit width

Effect of Slit Width on Resolution

Equal to the difference in wavelengths

Properties of an Ideal Transducer

General Classification of Transducers Photon transducers: photoelectric / quantum detectors

E-2 Photon Transducers E-2-1 Vaccum Phototubes

Photoemissive surfaces Bialkali: most sensitive

E-2-2 Photomultiplier Tubes

Nature of signal from a PMT

Dark Current in Photomultipliers

Silicon Photodiode Transducers

Charge-Transfer Devices (CTDs)

E-4 Photoconductivity Transducers

E-5 Thermal Transducers

Problem: thermal noise (thermal radiation emitted by other surfaces).

Examples of Thermal Transducers

You might also like