Application of Knowledge Management For Hazard Analysis in The Australian Dairy Industry
Application of Knowledge Management For Hazard Analysis in The Australian Dairy Industry
Application of Knowledge Management For Hazard Analysis in The Australian Dairy Industry
Fawzy Soliman
Introduction
The Hazard Analysis Critical Control Point (HACCP) was first developed in the 1960s by the Pillsbury company, the US Army Natick Laboratories and the National Aeronautics and Space Administration to ensure the safety of foods used in the space program. The original system was concerned only with microbiological hazards. During the 1970s and early 1980s, few food processors world wide embraced the HACCP approach. Although it was seen as an exciting initiative, the work involved in correctly implementing the requirements could not be justified. In Australia the HACCP principles were not fully understood, the process was considered too complicated and too many critical control points (CCPs) needed to be identified. However, recent food poisoning outbreaks highlight the lack of enforcement of food standards by the states and territories.
The author Fawzy Soliman is the Course Director at the School of Management, University of Technology, Sydney, Australia. Keywords Knowledge management, Knowledge-based systems Abstract Generic performance measures have emerged as appropriate tools for assessing the performance of the Hazard Analysis Critical Control Point (HACCP). These measures provide information for staffing decisions and budgetary development in the food manufacturing industry. They are also used to configure variations for costing, pricing, packaging and other functions. The HACCP performance measures have become powerful tools in the management of modern food manufacturers, in particular the dairy industry. The majority of decisions and rules used for assessing the performance of the HACCP method are too complex to capture in the form of a traditional programming language. Conventional information systems automate simple and rigid bookkeeping functions but knowledge management tools automate complex decision making and processes requiring judgement, and therefore are appropriate for automating the people-based knowledge of the HACCP performance assessment method. A new technique is presented to automate the HACCP performance assessment method using knowledge processing. Electronic access The current issue and full text archive of this journal is available at http://www.emerald-library.com
Journal of Knowledge Management Volume 4 . Number 4 . 2000 . pp. 287294 # MCB University Press . ISSN 1367-3270
287
Fawzy Soliman
provides state-of-the-art science for food safety. Like most quality systems today, HACCP is based on being proactive rather than reactive, doing it right the first time and so forth. With this type of approach, HACCP has gained strong awareness in the food industry, with strong interest generated in Australia through the first two Australian HACCP conferences held in Sydney (September, 1995 and April, 1996) and the third in Perth (May, 1997).
knowledge by means of knowledge bases. Such transformation of knowledge is an important component of knowledge management. Research indicates that there are six primary areas of knowledge in the HACCP performance method: (1) performance measures; (2) HACCP method; (3) verification; (4) internal performance measures; (5) external performance measures; and (6) relationships among ISO9000, HACCP and the NSW dairy industry and its regulation. 1. Performance measures According to Sellenhein (1991), the performance measure is an indicator that provides feedback on how a specific task is functioning compared with the rest of the dairy industry. The purpose of this measure is to guide and improve performance measurement systems, providing feedback to individuals on performance. Management needs to know how effective its plants are by identifying which activities are operating successfully and which activities are operating poorly. Information can enhance performance by providing motivation, with information about the correctness and adequacy of work behaviour, in turn providing workers with a sense of accomplishment, competence and control. The main goal of the HACCP performance measure is to monitor food production and assure that food is safe. Therefore specific measures need to be established to gain feedback about the effectiveness of HACCP which will ultimately result in safer food products. 2. HACCP method According to Bryan et al. (1993), a successfully implemented and maintained HACCP system offers High Assurance Of Food Safety. This is what all food industries should strive for. Studies have shown that to be truly successful, the following prerequisites should be followed (Kirby, 1994): . The HACCP system must have the full support from top management, with implementation driven from within the company. . The whole process from raw materials, preferably including supplier
288
Fawzy Soliman
accreditation, should be considered; and the staff made aware of the importance of quality. The importance of safety should be considered as a component of quality.
(2) confirms that safe food is being produced; and (3) provides feedback to the HACCP team and to management. Verification evaluates this by providing limits for each crucial step in the process, called a CCP. At each CCP, parameters are set to measure these steps, such as temperature, time, pH, water activity, microbial levels and so forth. The CCPs are monitored and adjusted constantly so as not to allow any deviation from the set limits. This principle thereby allows identification of whether the system is working, using the CCPs as performance measures of the internal workings of HACCP. 4. Internal performance measures Internal performance measures are mainly measures used during the verification stage. Examples of the internal performance measures are levels of housekeeping, personal hygiene, foreign objects, percentage of rejects, percentage of rework, time onhold, finished product quality and number of washings. 5. External performance measures The external environment consists of many elements outside the food manufacturer's boundaries. Food manufacturers need information and knowledge from their environment (internal and external) to make decisions and plans for the future. Before decisions concerning the future are made, external measurements are necessary, with the most common external measure used in the dairy industry being consumers' complaints and customers' satisfaction. Since the common external measures are based on customer feedback, the question to ask is: what knowledge from customer feedback may be used to assess the success of the HACCP method? 6. HACCP, total quality management (TQM), international standards organisation (ISO)/Australian standards (AS) Since most food manufacturing companies use HACCP as a foundation for their quality system, it is appropriate to incorporate the relationship between HACCP, TQM and the requirements for ISO/AS certification in the knowledge base for the HACCP performance method.
Principles of HACCP
A brief summary of the seven principles of the HACCP system is provided by Kirby (1994) as shown in Table I. 3. Verification Verification is a key part of correctly implementing the HACCP system (Pierson, 1995). Much of this verification has been derived from the ISO9000 series. Verification is also the least understood part of the HACCP system Pierson (1995) states that ``verification activities are still in their infancy relative to other HACCP activities''. Peters (1995) agrees: ``This is the least understood and implemented principle of the HACCP discipline''. According to Pierson (1995), the principle of verification provides three basic outcomes. It: (1) demonstrates that the HACCP system is operating correctly;
Table I The principles of HACCP (modified from Codex, 1993) Principle Subject 1 Hazard analysis Action
2 3 4
6 7
Construct a flow chart of the process stages. Identify and list all potential hazards Identification of critical Identify CCPs using a decision tree. control points (CCPs) Specify the systems of control Establishing critical limits Target values and critical limits must be set for each CCP Monitoring Continual or regular registering at each CCP to verify maintenance of control Correction Establish protocols for: (i) when CCPs are moving towards loss of control; and (ii) when CCPs are out of control Verification Establish systems to confirm the correct functioning of HACCP Documentation Establish documentation for all of the procedures and records necessary for the implementation and operation of the above procedures
289
Fawzy Soliman
It has been reported that the ISO 9000 /AS 3900 series of standards focus on the contracts and relationships between customers and suppliers, and conformity to customer specifications, rather than on internal operations of a quality management system (Harrigan, 1993). This is because certification for ISO has often been judged on the basis of the quality of an organisation's documentation management, rather than on the efficacy of the quality management system in achieving assured quality and safety of products. As a result it may be possible, although unlikely, for an ISO certified organisation to produce unsafe food. Current food legislation in New South Wales (NSW) will frequently provide for the possibility of a defence of due diligence by a food manufacturer, supplier, retailer or caterer. The adoption of HACCP or certification to ISO 9001/2 /AS 3901/2 is seen by many organisations as a responsible step providing the due diligence defence. That is why factors influencing the use of TQM, ISO and AS in the dairy industry are also included in the HACCP performance knowledge base.
(2) HACCP. (3) Food Processing Accreditation (FPA) for factories with export licences in accordance with the Australian Quarantine Inspection Services (AQIS) regime. (4) The HACCP9000 Quality Systems. For companies with HACCP, the NSW Dairy Corporation audits the plant based on a rating system which reflects the level of advancement in the HACCP program. The ratings scales are as follows: . A rated once per four months; . B rated once per two months; . C rated once per month; . D rated once per two weeks. Where a factory has a Corporation HACCP or an FPA program in place and is a rated ``A'' under the AQIS regime, there is no charge for three required inspections/audits. Where a factory is ``B'' rated or less under the AQIS regime, then each inspection/audit in excess of three is charged at a rate of $72.00 per hour (as of 1996). Where a factory does not have a quality system in place, the factory will be rated as ``B'', ``C'', or ``D'' and charged for all inspections (New South Wales Dairy Corporation, 1995/6).
290
Fawzy Soliman
This module uses a computational model to evaluate the various HACCP parameters required to perform the analysis (Soliman, 1998a). The five main functions performed by the evaluator module are as follows: (1) Standard level of monitoring. Each time the system is used, the calculation of frequency of occurrence, average time and standard deviation takes place. This calculation is performed for every case and for all activities during every shift. The evaluator module then calculates the weighted average times (WAT) and stores the results in the HACCP database. (2) Performance scores. A performance score for each HACCP is calculated by the normalisation of the standard levels of monitoring using a suitable interval of time. (3) HACCP levels. A safety level exists for every HACCP. The automated HACCP system employs HACCP safety levels, which are used to group HACCP into categories that reflect the magnitude of testing. The selection of the HACCP level defines the HACCP in relation to performance scores. (4) Production staff time. The production staff time required to provide testing to a sample is based on the degree of testing and the HACCP levels in place. (5) Number of production staff required. The automated HACCP system calculates (to the nearest whole number) the number of production staff required to ensure the level of HACCP desired in every shift. One important function of the HACCP performance system is forecasting the number of staff required for each shift. However, production staff rosters are usually prepared ahead, i.e. it is necessary to predict the production needs a few days ahead. In most cases this requires some input from experienced staff. The expert advice is usually based on historical decisions previously made in similar situations.
accumulating, organising and processing data. In the HACCP knowledge-based system, decisions made on the basis of HACCP performance are so complex that they need to be made efficient and regulated by means of a knowledge regulator.
291
Fawzy Soliman
based system presents the experts with a number of scenarios requiring decisions. Once product data and HACCP performance decisions are entered, the system automatically calculates the HACCP levels and displays the staffing levels required to provide performance testing and other duties.
Knowledge representation
Soliman (1998b) demonstrated that knowledge could be represented in the system through four models: elicitation model; structure model; model of expertise; and design model. These models are interrelated explicitly within the system to give the full benefits for problem solving, documentation, maintenance and explanation as described briefly below. . The elicitation model. The knowledge (in the form of decisions, protocols, policies, etc.) gained from the expert in the elicitation phase is described and used to define the elicitation model, which is the basis of the structure model. . The structure model. The structure model consists of the four contexts concept, activity, data flow and ordering contexts which are used for capturing the functional aspects of the system. In addition, the activities in the HACCP performance are defined in a process context. The contexts of the structure model are represented in the inference layers of the model of expertise. . The model of expertise. The model of expertise includes all functional requirements of the HACCP performance system. The non-functional requirements, such as efficiency of the problem-solving method, maintainability of the system or persistency of data are also considered. The function of the HACCP performance system is described in the model of expertise using first-order logic and dynamic logic for each layer of the model of expertise. . The design model. Decisions are captured within the design model, which interacts with the model of expertise. The design model allows description of data structures, algorithms and mathematical models. Transposing the HACCP performance functions (data and rules) in a concept context enhances the problem-
solving capabilities of the knowledgebased system (Soliman, 1998b). This close relationship with the concept context allows the experts to reason about real HACCP performance needs. In other words, the HACCP performance functions are represented in the knowledge-based system by foue views, namely: data view, function view, staff view and the control view. The most important entities here are the HACCP performance functions and events which are linked together to form the socalled event-driven HACCP performance functions. The knowledge-based system models the control flow of the HACCP performance functions and links the relevant entities generated by all the views. Accordingly, HACCP performance functions are easily connected to their input and output data which are located in the data view to model the data flow. Figure 1 illustrates the conceptual components of the HACCP knowledge-based system.
Computational results
The HACCP performance knowledge-based system was used in a medium size dairy manufacturer. Data collected after six months of operation indicate that considerable improvement has resulted from using the system. Table II compares the results obtained from the dairy manufacturer before and after the implementation of the system. The above measures do not include percentage recalls, percentage Salmonella detection, percentage Listeria detection or percentage downtime.
Conclusions
The application of knowledge management tools in the dairy industry enables monitoring of all dairy activities to ensure that consistent food safety is assured. For those companies with a HACCP system in place, maintaining the system is one of the main difficulties. The NSW Dairy Corporation grading system assesses the level of advancement in a HACCP system and this affects the number of audits. The better the grade the fewer the
292
Fawzy Soliman
Table II Results from dairy manufacturer Performance measure Level of housekeeping accomplishment Level of hygiene Level of microbial count % Rejects % Rework % Foreign objects found Customer complaints Customer satisfaction % Non-conformance Approval by external auditing body Improvement % +125 +100 +25 +25 +50 +33 +20 +100 +33 +16 Numbers 4 4 8 4 2 3 10 1 9 12 9 8 10 3 1 2 8 2 6 14
audits and therefore a useful performance measure is the number of audits. This is only compulsory in the dairy industry and hence would not be a common measure in any other food industry until a regulated law is enforced. Experience has shown that the manual HACCP method is expensive to maintain, as it requires time and effort to support.
Considerable savings and benefits may be obtained if some of the HACCP functions are computerised using knowledge management tools such as knowledge-based systems. The HACCP knowledge-based system is a computer software application which seeks to replicate the problem-solving and decisionmaking approaches of the HACCP experts. The HACCP knowledge-based system which is best suited for procedure-intensive tasks which involve the processing of large volumes of HACCP data manipulates facts, relationships between those facts, and heuristics (or rules of thumb) within a narrow and bounded HACCP area. During its development, a vast body of task-specific knowledge from a human is transferred into a computing environment. Although many of the benefits of knowledge management tools are difficult to quantify, empirical support linking these tools with cost savings and improved quality has been reported. In addition to delivering higher quality outputs which leads to increased customer satisfaction, knowledge
293
Fawzy Soliman
management technology enables human resource scarcities to be overcome through ``smarter'' work. In conclusion, the use of knowledge management tools in HACCP will make major advances into redefining food safety and care away from physically driven processes and towards an knowledgeintensive system. The extent to which food manufacturers are cognisant of the knowledge management multi-mission capabilities in itself does not guarantee the successful implementation of a flexible strategy; rather, strategy, organisational design and incentives must match the new opportunities offered by the multidimensional and complex offerings of knowledge management systems.
References
Bryan, F.L., Guzewich, J.J. and Todd, E.C.D. (1993), ``Use of the hazard analysis critical control point approach by state, provincial and local food protection agencies: results of a survey and discussion'', Dairy, Food and Environmental Sanitation, Vol. 13 No. 6, pp. 323-31.
Davenport, T.H. and Prusak, L.P. (1998), Working Knowledge: How Organizations Manage What they Know, Harvard Business School Press, Boston, MA. Harrigan, W.F. (1993), ``The ISO 9000 series and its implication for HACCP'', Food Control, Vol. 4 No. 2, pp. 105-11. Kirby, K. (1994), ``HACCP in practice'', Food Control, Vol. 5 No. 4, pp. 230-36. New South Wales Dairy Corporation (1995/6), Annual Report, Chippendale. Nonaka I. and Takeuchi, H. (1995), The Knowledge Creating Company, Oxford University Press, New York, NY. Notermans, S., Zweitering, M.H. and Mead, G.C. (1994), ``The HACCP concept: identification of potentially hazardous micro-organisms'', Food Microbiology, Vol. 11 No. 3, pp. 203-14. Peters, R. (1995), ``What is HACCP?'', Proceedings of the First Australian HACCP Conference, Food Operations. Pierson, M. (1995), ``HACCP verification'', Proceedings of the First Australian HACCP Conference, Food Operations. Sellenhein, M.R (1991), ``Performance measurement'', Management Accounting, September, pp. 50-53. Soliman, F. (1998a), ``Automation of patient dependency systems'', Journal of Medical Systems, Vol. 22 No. 4, pp. 225-36. Soliman, F. (1998b), ``Patient dependency knowledge based systems'', Journal of Medical Systems, Vol. 22 No. 5, pp. 353-66.
294