Product Data Sheet Edition 11.2006 Version no. 10.

06

Sikafloor-381 N
2-part self smoothing epoxy coating, highly chemically and mechanically resistant

Construction

Product Description
Uses

Sikafloor-381 N is a two part, self-smoothing, coloured epoxy resin with high chemical and mechanical resistance. Chemically and mechanically highly resistant coating for concrete and screed surfaces in bund areas for protection against water contaminating liquids (according to the product chemical resistance table) High chemical resistance High mechanical resistance Liquid proof Abrasion resistant Slip resistant surface possible

Characteristics / Advantages

Product Data
Form Appearance / Colours Resin - part A: Hardener - part B: coloured, liquid transparent, liquid

Almost unlimited choice of colour shades. Under direct sun radiation there may be some discolouration and colour deviation, this has no influence on the function and performance of the coating. Packaging Part A: Part B: Part A+B: 21.25 kg containers 3.75 kg containers 25 kg ready to mix units

Storage Storage Conditions / Shelf-Life 24 months from date of production if stored properly in original, unopened and undamaged sealed packaging, in dry conditions at temperatures between +5C and +30C.

Technical Data
Chemical Base Density Epoxy Part A: Part B: Mixed resin: ~ 1.77 kg/l ~ 1.04 kg/l ~ 1.6 kg/l (DIN EN ISO 2811-1)

All Density values at +23C Solid Content Mechanical / Physical Properties Compressive Strength Flexural Strength > 80 N/mm (14 days / +23C) > 55 N/mm (14 days / +23C) (EN 196-1) (EN 196-1) ~ 100% (by volume) / ~ 100% (by weight)

SikafloorPP-381 N

1/5

Bond Strength Shore D Hardness Abrasion Resistance Resistance Chemical Resistance Thermal Resistance

> 1.5 N/mm 82

(failure in concrete) (7 days / +23C)

(ISO 4624) (DIN 53 505) (DIN 53 109) (Taber Abrader Test))

40 mg (CS 10/1000/1000) (8 days / +23C)

Resistant to many chemicals. Please ask for a detailed chemical resistance table.

Exposure* Permanent Short-term max. 7 d Short-term max. 12 h

Dry heat +50C +80C +100C

Short-term moist/wet heat* up to +80C where exposure is only occasional (i.e. during steam cleaning etc.)
*No simultaneous chemical and mechanical exposure.

System Information
System Structure Self-smoothing system (horizontal areas): Primer: 1 x Sikafloor-156 Wearing course: 1 x Sikafloor-381 N filled with quartz sand Smooth wearing course (vertical areas): Smooth wearing course: 1 x Sikafloor -156 Wearing course: 2 x Sikafloor -381 N + Extender T Broadcast system with slip resistance: Primer: 1 x Sikafloor -156 Wearing course: 1 x Sikafloor-381 N broadcast to excess with silicon carbide or quartz sand Seal coat: 1 x Sikafloor-381 N + 5 wt.-% Thinner C

Application Details
Consumption / Dosage
Coating System Primer Levelling (optional) Wearing course horizontal areas (1.8 - 2.8 mm) Wearing course vertical areas Product Sikafloor -156 Sikafloor -156 mortar

Consumption 0.3 - 0.5 kg/m Refer to PDS of Sikafloor -156 1.8 kg/m /mm Binder + quartz sand 10 - 15C: without filling 15 - 20C: 1 : 0.1 pbw (1.65 + 0.15 kg/m) 20 - 30C: 1 : 0.2 pbw (1.5 + 0.3 kg/m)
2

Sikafloor -381 N filled with quartz sand 0.1 - 0.3

Sikafloor -381 N + 2.5 - 4 wt.-% (Film thickness ~ 1.5 mm) Extender T

2 x 1.25 kg/m

Sikafloor -381 N, 1.6 kg/m Binder without filling broadcast to excess with silicon carbide Silicon Carbide 0.5 - 1.0 mm or (Film thickness ~ 2.5 mm) 0.5 - 1.0 mm or quartz quartz sand 0.4 - 0.7 mm sand 0.4 - 0.7 mm (5 - 6 kg/m) Wearing course with slip resistance Seal coat (on broadcast areas only) Sikafloor -381 N + 5 wt.-% Thinner C

0.75 - 0.85 kg/m

These figures are theoretical and do not allow for any additional material due to surface porosity, surface profile, variations in level or wastage etc. Substrate Quality The concrete substrate must be sound and of sufficient compressive strength 2 2 (minimum 25 N/mm ) with a minimum pull off strength of 1.5 N/mm . The substrate must be clean, dry and free of all contaminants such as dirt, oil, grease, coatings and surface treatments, etc.. If in doubt apply a test area first.

SikafloorPP-381 N

2/5

Substrate Preparation

Concrete substrates must be prepared mechanically using abrasive blast cleaning or scarifying equipment to remove cement laitance and achieve an open textured surface. Weak concrete must be removed and surface defects such as blowholes and voids must be fully exposed. Repairs to the substrate, filling of blowholes/voids and surface levelling must be carried out using appropriate products from the Sikafloor , SikaDur and SikaGard range of materials. The concrete or screed substrate has to be primed or levelled in order to achieve an even surface. High spots must be removed by e.g. grinding. All dust, loose and friable material must be completely removed from all surfaces before application of the product, preferably by brush and/or vacuum.

Application Conditions/

Limitations
Substrate Temperature Ambient Temperature Substrate Moisture Content +10C min. / +30C max. +10C min. / +30C max. < 4% pbw moisture content. Test method: Sika-Tramex meter,CM - measurement or Oven-dry-method. No rising moisture according to ASTM (Polyethylene-sheet). Relative Air Humidity Dew Point 80% r.h. max. Beware of condensation! The substrate and uncured floor must be at least 3C above dew point to reduce the risk of condensation or blooming on the floor finish. Application Instructions Mixing Mixing Time Part A : part B = 85 : 15 (by weight) Prior to mixing, stir part A mechanically. When all of part B has been added to part A, mix continuously for 2 minutes until a uniform mix has been achieved. When parts A and B have been mixed, add the quartz sand 0.1 - 0.3 mm and mix for a further 2 minutes until a uniform mix has been achieved. To ensure thorough mixing pour materials into another container and mix again to achieve a consistent mix. Over mixing must be avoided to minimise air entrainment. Mixing Tools Application Method / Tools
Sikafloor -381 N must be thoroughly mixed using a low speed electric stirrer (300 400 rpm) or other suitable equipment.

Prior to application, confirm substrate moisture content, relative humidity and dew point.
If > 4% pbw moisture content, Sikafloor EpoCem should be applied as a T.M.B. (temporary moisture barrier) system.

Wearing course (horizontal areas): Sikafloor -381 N is poured, spread evenly by means of a serrated trowel. Roll immediately in two directions with a spiked roller to ensure even thickness. Wearing course (vertical areas): The first layer of Sikafloor -381 N, mixed with 2.5 - 4% Extender T, has to be applied by trowel. After curing, apply the second layer of Sikafloor -381 N, mixed with 2.5 - 4% Extender T, by trowel. Wearing course with slip resistance: Sikafloor-381 N is poured, spread evenly by means of a serrated trowel and blind the fresh layer with silicon carbide or quartz sand to excess. After final drying the surplus silicon carbide / quartz sand must be swept off and the surface must be vacuumed. The seal coat (Sikafloor-381 N + 5 wt.-% Thinner C) has to be applied evenly by short-piled roller or squeegee. Cleaning of Tools Clean all tools and application equipment with Thinner C immediately after use. Hardened and/or cured material can only be removed mechanically.

SikafloorPP-381 N

3/5

Potlife
Temperatures +10C +20C +30C Time ~ 60 minutes ~ 30 minutes ~ 15 minutes

Waiting Time / Overcoating

Before applying Sikafloor-381 N on Sikafloor-156 allow:

Before applying Sikafloor-381 N on Sikafloor-381 N allow:

Times are approximate and will be affected by changing ambient conditions, particularly temperature and relative humidity. Notes on Application / Limitations
Do not apply Sikafloor -381 N on substrates with rising moisture.

Do not blind the primer. Freshly applied Sikafloor -381 N must be protected from damp, condensation and water for at least 24 hours. Avoid puddles on the surface with the primer. Tools Recommended supplier of tools: PPW-Polyplan-Werkzeuge GmbH, Phone: +49 40/5597260, www.polyplan.com Serrated trowel for smooth wearing layer: e.g. Large-Surface Scrapper No. 565, Toothed blades No. 25 The incorrect assessment and treatment of cracks may lead to a reduced service life and reflective cracking.
For exact colour matching, ensure Sikafloor -381 N in each area is applied from the same control batch numbers.

Under certain conditions, underfloor heating or high ambient temperatures combined with high point loading, may lead to imprints in the resin. If heating is required do not use gas, oil, paraffin or other fossil fuel heaters, these produce large quantities of both CO2 and H2O water vapour, which may adversely affect the finish. For heating use only electric powered warm air blower systems.

Curing Details
Applied Product ready for use

Temperature +10C +20C +30C

Foot traffic ~ 24 hours ~ 18 hours ~ 12 hours

Light traffic ~ 3 days ~ 2 days ~ 1 day

Full cure ~ 10 days ~ 7 days ~ 5 days

Note: Times are approximate and will be affected by changing ambient conditions. Cleaning / Maintenance Methods
To maintain the appearance of the floor after application, Sikafloor -381 N must have all spillages removed immediately and must be regularly cleaned using rotary brush, mechanical scrubbers, scrubber dryer, high pressure washer, wash and vacuum techniques etc using suitable detergents and waxes

SikafloorPP-381 N

4/5

Value Base Local Restrictions Health and Safety Information Legal Notes

All technical data stated in this Product Data Sheet are based on laboratory tests. Actual measured data may vary due to circumstances beyond our control. Please note that as a result of specific local regulations the performance of this product may vary from country to country. Please consult the local Product Data Sheet for the exact description of the application fields. For information and advice on the safe handling, storage and disposal of chemical products, users should refer to the most recent Material Safety Data Sheet containing physical, ecological, toxicological and other safety-related data.
The information, and, in particular, the recommendations relating to the application and end-use of Sika products, are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sikas recommendations. In practice, the differences in materials, substrates and actual site conditions are such that no warranty in respect of merchantability or of fitness for a particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any written recommendations, or from any other advice offered. The user of the product must test the products suitability for the intended application and purpose. Sika reserves the right to change the properties of its products. The proprietary rights of third parties must be observed. All orders are accepted subject to our current terms of sale and delivery. Users must always refer to the most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika Egypt for Construction Chemicals El Abour City 1st industrial zone (A) Section # 10 Block 13035, Egypt

Tel :+202- 6100714/15/16/17/18 Fax :+202- 6100759 Mob :+2012- 3908822/55 www.sika.com.eg

SikafloorPP-381 N

5/5