NXP TDA11136PC305CG SERIES

S
SSE
EER
RRV
VVI
IIC
CCE
EE M
MMA
AAN
NNU
UUA
AAL
LL
COLOUR TELEVISION
.

2

SAFETY PRECAUTIONS
1. The design of this product contains special hardware, many
circuits and components specially for safety purposes. For
continued protection, no changes should be made to the
original design unless authorized in writing by the
manufacturer. Replacement parts must be identical to those
used in the original circuits. Service should be performed by
qualified personnel only.

2. Alterations of the design or circuitry of the products should
not be made. Any design alterations or additions will void
the manufacturers warranty and will further relieve the
manufacturer of responsibility for personal injury or property
damage resulting therefrom.

3. Many electrical and mechanical parts in the products have
special safety-related characteristics. These characteristics
are often not evident from visual inspection nor can the
protection afforded by them necessarily be obtained by
using replacement components rated for higher voltage,
wattage, etc. Replacement parts which have these special
safety characteristics are identified in the parts list of
Service manual. Electrical components having such
features are identified by shading on the schematics
and by ( ) on the parts list in Service manual. The
use of a substitute replacement which does not have the
same safety characteristics as the recommended
replacement part shown in the parts list of Service manual
may cause shock, fire, or other hazards

4. Dont short between the LIVE side ground and
ISOLATED (NEUTRAL) side ground or EARTH side
ground when repairing. Some models power circuit is
partly different in the GND. The difference of the GND is
shown by the LIVE: ( ) side GND, ISOLATED
(NEUTRAL) : ( ) side GND and EARTH : ( ) side GND.
Dont short between the LIVE side GND and ISOLATED
(NEUTRAL) side GND or EARTH side GND and never
measure with a measuring apparatus (oscilloscope etc.) the
LIVE side GND and ISOLATED (NEUTRAL) side GND or
EARTH side GND at the same time. If above note will not
be kept, a fuse or any parts will be broken.

5. If any repair has been made to the chassis, it is
recommended that the B1 setting should be checked or
adjusted (See ADJUSTMENT OF B1 POWER SUPPLY).

6. The high voltage applied to the picture tube must conform
with that specified in Service manual. Excessive high
voltage can cause an increase in X-Ray emission, arcing
and possible component damage, therefore operation under
excessive high voltage conditions should be kept to a
minimum, or should be prevented. If severe arcing occurs,
remove the AC power immediately and determine the cause
by visual inspection (incorrect installation, cracked or
melted high voltage harness, poor soldering, etc.). To
maintain the proper minimum level of soft X-Ray emission,
components in the high voltage circuitry including the
picture tube must be the exact replacements or alternatives
approved by the manufacturer of the complete product.

7. Do not check high voltage by drawing an arc. Use a high
voltage meter or a high voltage probe with a VTVM.
Discharge the picture tube before attempting meter
connection, by connecting a clip lead to the ground frame
and connecting the other end of the lead through a 10k
2W resitor to the anode button.

8. When service is required, observe the original lead dress.
Extra precaution should be given to assure correct lead
dress in the high voltage circuit area. Where a short circuit
has occurred, those components that indicate evidence of
overheating should be replaced. Always use the
9. manufacturers replacement components.
10. Isolation Check
(Safety for Electrical Shock Hazard)
After re-assembling the product, always perform an
isolation check on the exposed metal parts of the cabinet
(antenna terminals, video/audio input and output terminals,
Control knobs, metal cabinet, screwheads, earphone jack,
control shafts, etc.) to be sure the product is safe to operate
without danger of electrical shock.
11. The surface of the TV screen is coated with a thin film which
can easily be damaged. Be very careful with it when handle
the TV. Should the TV screen become soiled, wipe it with a
soft dry cloth. Never rub it forcefully. Never use any cleaner
or detergent on it.

(1) Dielectric Strength Test
The isolation between the AC primary circuit and all metal
parts exposed to the user, particularly any exposed metal
part having a return path to the chassis should withstand a
voltage of 3000V AC (r.m.s.) for a period of one second.
(Withstand a voltage of 1100V AC (r.m.s.) to an
appliance rated up to 120V, and 3000V AC (r.m.s.) to an
appliance rated 200V or more, for a periode of one second.)
This method of test requires a test equipment not generally
found in the service trade.
(2) Leakage Current Check
Plug the AC line cord directly into the AC outlet (do not use
a line isolation transformer during this check.). Using a
Leakage Current Tester, measure the leakage current
from each exposed metal part of the cabinet, particularly
any exposed metal part having a return path to the chassis,
to a known good earth ground (water pipe, etc.). Any
leakage current must not exceed 0.5mA AC (r.m.s.).
However, in tropical area, this must not exceed 0.2mA AC
(r.m.s.).
Alternate Check Method
Plug the AC line cord directly into the AC outlet ( do not use
a line isolation transformer during this check.). Use an AC
voltmeter having 1000 ohms per volt or more sensitivity in
the following manner. Connect a 1500 10W resistor
paralleled by a 0.15F AC-type capacitor between an
exposed metal part and a known good earth ground (water
pipe, etc.). Measure the AC voltage across the resistor with
the AC voltmeter. Move the resistor connection to each
exposed metal part, particularly any exposed metal part
having a return path to the chassis, and measure the AC
voltage across the resistor. Now, reverse the plug in the AC
outlet and repeat each measurement. Any voltage
measured must not exceed 0.75V AC (r.m.s.). This
corresponds to 0.5mA AC (r.m.s.).
However, in tropical area, this must not exceed 0.3V AC
(r.m.s.).
This corresponds to 0.2mA AC (r.m.s.)


.

3

TV Block diagram




























TUNER
SAW
IF IN R IN

RF AGC GIN

B IN

CHROMA
VIDEO
CVBS/Y IN

CVBS1 IN
CVBS2 IN

SDA
SCL MA IN L
MAOUTR MA IN R
MAOUTL
RGB OUT
V OUT H OUT

Vo
V2i
AR i1
R
G
B
ARi 2
ALi 2
ALi2
ALi1
24C08

POWER
UNIT
130V
24V
+13V
8V
5V
3.3V
CRT PCB
V IN

TDA8177

V OUT
H IN

H OUT

H OUT
DY
200V
SCREEN
FOCUS
TDA11105-XXXX
Vi1
OUT1-
OUT1+

Vi2
OUT2-
OUT2+

AN17821
CRT
ALo
ARo
C
ALi 1
4052
audio

audio
audio
video
video
bus

video
Video IN
video
8V
-13V
.

4





5

REPLACEMENT OF MEMORY IC

1. MEMORY IC.
This TV uses memory IC. In the memory IC are memorized data for correctly operating the video and
deflection circuits.
When replacing memory IC, be sure to use IC written with the initial value of data.

2. PROCEDURE FOR REPLACING MEMORY IC
(1) Power off
Switch the power off and unplug the power cord from AC outlet.
(2) Replace IC
Be sure to use memory IC written with the initial data values.
(3) Power On
Plug the power cord into the AC outlet and switch the power On.
(4) Check and set SYSTEM default value:
3. Note: enter a factory mode method
1) Factory remote control: Press the factory remote control up [PRESET], press again[TEST]key,
appear on the television screen 'M'.
2) Customer remote control
3) Press [menu] key, appear the picture menu, press few character keys 6483, the screen
appears M.
4) Press [standby] key, withdraw factory mode.
5) The TEST will be displayed on the screen.
6) Check the setting value of the SYSTEM default value of Table below. If the value is different,
select items by [CH+]/[CH-] keys and set value by [VOL+]/[VOL-] keys.
7) Press STANDBY key again and return to the normal screen.

SERVICE ADJUSTMENT

B1 POWER SUPPLY
1. Receive normal colour bar signal.
2. Connect DC voltmeter to D551- and isolated ground.
3. Adjust potentiometer in power unit to get the voltage as 110V 1.0V for 21 inch hereinafter,
130 1.0V for 25 inch upwards.
FOCUS ADJUSTMENT
1. Receive a crosshatch signal.
2. While watching the screen, adjust the FOCUS VR to make the vertical and horizontal lines as fine
and sharp as possible.
BUS CONTROL ADJUSTMENT
To enter BUS control mode, Press TEST key on the Remote control unit of factory. Customer remote
control press "MENU" key behind in a row press"6""4""8""3"
Choose a "SETUP SELECT" options in"M2" menu, Change"SETUP SELECT 0"to"SETUP SELECT 1"
press "MUTE" key again can depend on this get into "M3"~"M9" of design menu, general factory the


6

production doesn't need to carry on M 3~ adjustments of M9.
In "M0"~under"M9" appearance press CALL the key can get into "M" appearance.
At Munder the appearance press -/- the key can get into BUS OPEN appearance, at BUS OPEN under,
press -/- the key recover factory appearance.

Remote Hand Unit keys
[M1] [M2] [M3]





[M0]



[M1] menu
MENU0 Geometrical adjustment
Receive PAL standard Complete pattern signal.
Adjustment steps
a) Adjust V. SLOPE, to the center horizontal line just appeare from half bottom shadow.
b) Adjust V. SIZE, to get 90% of vertical picture contents would be displayed on CRT.
c) Adjust V. SHIFT, the center horizontal line correspond to CRT vertical center.
d) Adjust H.SHIFT, to get the picture horizontal center correspond to CRT horizontal center.

Receive NTSC signal and repeat above [M0] and [M1] adjustment.
[M2] Menu
AGC Adjustment.
Receive 60dB(1mV)V
H
colour bar pattern signaladjust AGC valuevoltage from high to lowto noise
reduce gradually and just disappeared point.
Select shipping, push [V+] [V-]key to be shipped.
[M3] Menu
CRTcut off and white balance adjustment.
Receive white signal.
a) CRT cut off adjustment.
1. Select SC, then automatically vertical scan will be stopped.
2. Adjust SCREEN control on Flyback transformer to get the darkest single horizontal line (red,
green, or blue, sometimes shows more yellow, more purple or more white).

b) White balance adjustment.
1. Select RD/BD menu.
2. Adjust RD/BD to get colour temperature as x=281, y=311
c) Sub-Brightness adjustment. (Use stair case signal)
1. Select SB menu.
2. Adjust SB to get the darkest step being cutoff.

C CC C C CC C C CC C
C CC C
C CC C C CC C
Horizontal line
Shado
a


7

I
2
C standard UOC for export bus control adjustment item default setting 2007-12-05
MI Items Variable Preset recommendation
M0 50HZ 60HZ 50HZ 60HZ
TEST.SE 0/1 Choice of test signal
V. SLOPE 63 +/-32 Picture vertical center adjustment 35 -01
V. POSI 63 +/-32 Vertical positions adjustment 40 -1
V. SIZE 63 +/-32 Vertical amplitude adjustment 20 +02
V. SC 63 +/-32 Vertical S Correction Adjustment 25 -01
V.LINE 63 +/-32 Vertical line Adjustment 18 +02
V.SCR 63 +/-32 Vertical S Correction R 32 -01
H.PSASE 15 +/-32 Horizontal position adjustment 40 0
EW.W 63 +/-32 Horizontal amplitude adjustment 55 0
EW.PW 63 +/-32 E/W amplitude adjustment 29 0
EW.TC 63 +/-32 Picture trapezoid adjustment 31 0
EW.UCP 63 +/-32 Picture top Cape adjustment 48 0
EW.LCP 63 +/-32 Picture bottom Cape adjustment 45 0
H.BOW 63 +/-32 Picture bow form adjustment 30 0
H.PAR 63 +/-32 Picture parallelogram adjustment 31 0
H.BLK.SW ON/OFF Horizontal blank switch ON
H .BLK.L 15 +/-7 Horizontal left blank adjust 0
H .BLK.R 15 +/-7 Horizontal right blank adjust 0
V X 63 +/-32 Vertical zoom step 20
RGB 63 +/-32 RBG hor. offset 32

M1 TV /DVD
CL 0~15 Contrast level offset 10
BLOC 0~15 Black level offset course 6
R.BIA 0~63 R OUT Amplitude Adjustment 32
G.BIA 0~63 32 G OUT Amplitude Adjustment 32 -6
B.BIA 0~63 B OUT Amplitude Adjustment 32
R.DRV 0~63 R OUT Amplitude Adjustment 32
G.DRV 0~63 G OUT Amplitude Adjustment 32
B.DRV 0~63 B OUT Amplitude Adjustment 32
SUB BRT 0~63 Brightness of screen line 32
VSD 0~1 Vertical Ramp Out Stop Selection
TEST.S 0~5

M2 50HZ 60HZ
RF AGC 0~63 32 Tuner AGC Takeover Point Adjustment 18
OSD.V.POS 0~63 0~63 Vertical position of OSD 16 22
OSD.H.POS 0~63 Horizital position of OSD 9
OSD BRT 0~15 OSD brightness 15
SHIPPING


8

SETUP SELECT 0~1 Select 1, press the MUTE key to M 3~ M9

M3 SUB CONT 0~63 Sub contrast 63
SUB COLOR 0~63 Sub colour 63
SUB SHARP 0~63 Sub sharpness 63
SUB TINT 0~63 Sub tint 32
BTC 0~63 32
COF 0~1 Cut-off control range
0:normal control range 1:extended control range
1
FRENCH ON/OFF OSD language selection ON
TURKISH ON/OFF OSD language selection ON
PORTUGUESE ON/OFF OSD language selection ON
BULGARINA ON/OFF OSD language selection ON
RUSSIAN ON/OFF OSD language selection ON
FARSI ON/OFF OSD language selection ON
ARABIC ON/OFF OSD language selection ON
RUMANIAN ON/OFF OSD language selection ON
SPANISH ON/OFF OSD language selection ON
HUNGARIAN ON/OFF OSD language selection ON
POLISH ON/OFF OSD language selection ON
CZECH ON/OFF OSD language selection ON
SLOVENE ON/OFF OSD language selection ON
CROATIAN ON/OFF OSD language selection ON
MACEDONIAN ON/OFF OSD language selection ON
SERBIAN ON/OFF OSD language selection ON
GREEK ON/OFF OSD language selection ON

M4 VA 0~3 Vercital amplitude 0
VAI 0~1 System I output signal amplitude correction 0:no
correction 1:amplitude + 12%
1
CBS 0~1 Control sequence of beam current limiting 0:normal
operation(contrastbrightness) 1:control on
contrast and brightness in parallel
1
COR 0~1 Video dependent coring(peaking)
0:off 1:coring active between 0 and 20 IRE
0
RPA 0~3 Ratio pre-and aftershoot 2
RPO 0~3 Ratio of positive and negative peaks 2
TCI2X 0~1 Top sync clamp current of the CVBS/Y input clamp
0: clamp current about 80 uA 1: clamp current
about 160 uA
0
BKS ON/OFF Baack stretch ON
BSD 0~1 Black stretch Depth 0:15IRE 1:30 IRE 0
AAS 0~3 Black area to switch off the black stretch 0


9

PWL 0~1 Peak white limiting 0:peak white limiting circuit not
active 1:peak white limiting circuit active

SOC 0~1 Soft clip adjust 0
PWLDAC 0~15 Peak white adjust 2
CHSE 0~15 Color degree identifies an intelligent degree 2
S.IDENT ON/OFF S-VIDEO Identify switch ON
TFR 0~1 Transfer ratio
0:no black level shift due to video content
1:black level shift 10 IRE for a white picture
0
DSK 0~1 Dynamic skin control on/off 0:off 1:on 0
DSA 0~1 Dynamic skin tone angle 0:123 1:117 0
WS 0~1 0
BLS 0~1 Blue stretch mode 0:off 1:on 0
GAME ON/OFF Game switch ON
CALENDAR ON/OFF CALENDAR switch
M5 IF Vision IF of RF (38/38.9/45.75/58.75) MHZ 38.9MHZ
OIF 0~63 IF compensate 32
FFI 0~1 Fast filter IF -PLL 0
AGCS 0~3 AGC speed 0
DCXO 0~3 Crystal load electric capacity compensate 2
FSL 0~1 Forced slicing level for vertical sync 0
SSL 0~1 Slicing level for horizontal sync separator 0:50%
1:30%,direction top sync
0
GD 0~1 Group delay on CVBSI signal 0:no group delay
correction 1: group delay correction switched on
0
HP2 0~1 Sync hronization of OSD/TEXT display 0
AKB ON/OFF Black current stabilization OFF
DFL 0~1 Disable flash protection from deflection timer
0:restart horizontal output,after flash protection,via
slow start 1: restart horizontal output,after flash
protection,with typical duty-cycle
0
XDT 0~1 x-ray detection on/off 0
FBC 0~1 Fixed beam current switch off 0
QDT 0~1 0
FBC1 0~1 Fixed beam curuent during switch off
0:fixed beam current is 1 mA
1:fixed beam current is 2 mA
0
FSPS 0~1 Selection of left or right hand side in split-Screen
mode
0
FSPB 0~1 Blanking in split-screen mode 0
FSPE 0~1 Enable split-screen mode for demonstration of
features
0
HCO 0~1 EHT tracking mode 0


10

OSVE 0~1 Black current measuring lines in overscan(for
vertical zoom setting 1)
0
EVB 0~1 Extended vertical blanking 0
IFS.RED 0~1 IF Intelligent degree 1
PWM.VOL ON/OFF OFF
MUTE MODE 0~2 0: internal + external control 1: control 2:
external control

M6 CLF 0~1 Selection internal clamp speed 0:clamp slow
1:clamp 6 times faster
0
BPB 0~1 Enable bypass of sound bandpass filter at mono
mode 0:sound bandpass active for mono
demodulator 1:sound bandpass filter bypassed
0
BPB2 0~1 Bypass sound bandpass filter section 2
0:bandpass filter active 1:bandpass filter bypassed
0
FMWS 0~3 Window select for FM demodulator 0
AGN 0~1 Gain FM demodulator 0:normal operation 1:gain +6
dB
1
AGNE 0~3 FM sound demodulator outopt signal amplitude 1
AVL ON/OFF Auto volume levelling OFF
AVLE 0~1 AVL function on East-West output pin 0
DSGLS 0~1 Extra gain selection loudspeaker outputs 0:+0 Db
1:+6 Db
0
NRR 0~1 No red reduction during blue stretch 0
AMLOW 0~1 Audio output signal for AM sound 0
GSSIF 0~1 Extra gain-range SSIF for AM demodulation 0
V.P1 0~100 V.P1 volume of VALUE 10
V.P25 0~100 V.P25 volume of VALUE 45
V.P50 0~100 V.P50 volume of VALUE 70
V.P75 0~100 V.P75 volume of VALUE 85
V.MAX 0~60 Volume max
ON DL 0~18 On delay time 3
OFF DL 0~7 Off delay time 1
ON/OFF MODE 0~1 0

M7 NAT N-USA/PAL N-JPN/PAL N-USA/PAL PAL MAT
ACL 0~1 Automatic color limiting 0:not active 1:active 0
CB 0~1 Chroma bandpass center frequency 0
SBO 0~1 SECAM B-Y blank level offset adjustment 0
BPS 0~1 Bypass of chroma base-band delay line 0:active
1:bypassed
0
FCO 0~1 Forced Color-on 0:on 1:off 0


11

DTR 0~1 Chroma trap mode
0:single chroma trap
1:dual chroma trap,more suppression but less
bandwidth
0
Y.P 0~15 Y-delay adjustment for PAL signal 8
Y.N 0~15 Y-delay adjustment for NTSC signal 8
Y.AV 0~15 Y-delay adjustment for PAL signal in AV mode 8
Y.SVHS 0~15 Y-delay adjustment for PAL signal in S-video mode 8
PF.P 0~3 PAL Center frequency with postpone adjust 0
PF.N 0~3 NTSC Center frequency with postpone adjust 0
PF.AV 0~3 AV Center frequency with postpone adjust 0
C.PHI.1

M8 S.BRT 0~100 Standard Brightness in pp mode 75
S.CONT 0~100 Standard Contrast in pp mode 75
S.COLOR 0~100 Standard Color in pp mode 50
S.SHARP 0~100 StandardSharpness in pp mode 50
D.BRT 0~100 dynamic Brightness in pp mode 75
D.CONT 0~100 dynamic Contrast in pp mode 100
D.COLOR 0~100 dynamic Color in pp mode 75
D.SHARP 0~100 dynamicSharpness in pp mode 75
M.BRT 0~100 mild Brightness in pp mode 40
M.CONT 0~100 mild Contrast in pp mode 40
M.COLOR 0~100 mild Color in pp mode 40
M.SHARP 0~100 mildSharpness in pp mode 40
W.BRT 0~100 factory adjusts Brightness 50
W.CONT 0~100 factory adjusts Contrast 75
W.COLOR 0~100 factory adjusts Color 0
SC BRT 0~100 Subsidiary Bright Adjustment 50
COOL 0~63 Cool color adjustment 8
WARM 0~63 Warm color adjustment 8

M9 AV2 ON/OFF AV2 selection ON
SVHS ON/OFF S-VIDEO selection ON
DVD ON/OFF DVD Y U V selection ON
EURO ON/OFF SCART selection ON
AUTO SOUND ON/OFF Auto sound system as auto search ON
BG ON/OFF Sound system of 6.0M selecting ON
I ON/OFF Sound system of 5.5M selecting ON
M ON/OFF Sound system of 4.5M selecting ON
DK ON/OFF Sound system of 6.5M selecting ON
SIF PRI ON/OFF Force sound system as auto search ON
POWER REST 0~3 AC power on start selection 1


12

BANLANCE ON/OFF AV stereo selection (ON:AV STEREO OFF:MONO) OFF
HALFTONE ON/OFF Half tone select OFF
KEY OPT SANYO/MEK KEY BOARD selection SANYO
CURTAIN 0~2 CURTAIN selection 2
LOGO ON/OFF Logo selection OFF
B BACK ON/OFF ON
TILT ON/OFF TILT selection OFF
ASM OPT 0~1 Search speed selection 1
V.MUTE P.OFF ON/0~7 Select whether cutoff RGB ouput from solution
whlie power off
ON
AV OUT CVBS: AV output to follow the screen IF: AV
output has always been to follow the TV
CVBS
COMBO USB/DVD/OFF Extensions to choose






KEY BOARD: multiple-choice test(0/1)
0: Control keys input (Max. Limit voltage) ---(MEK KEY BOARD)



1: Control keys input (Max. Limit voltage) (SANYO KEY BOARD)

4 , LOGO EDIT
This software LOGO is a pair of pleased words and customer to edit 2 kinds, at the M_MODE, long
press[P.P]the key can get into a pair of pleased words editor appearance.
( Operate

Press[1]/[2] keys: The LOGO perpendicular position adjust, [1] adjusts upward, [2] get down
adjustment;
Press[3]/[4] keys: The LOGO level position adjust, [3] is to the left adjustment, [4] rightwards adjusts;
Press[REVIEW]key: Withdraw LOGO editor appearance, the LOGO information remembers EEPROM and
return to M_MODE;
Press again[MENU]the key can get into and can edit LOGO appearance.
( Operate

Press[1]/[2] keys: The LOGO perpendicular position adjust, [1] adjusts upward, [2] get down
adjustment;
Function POWER MENU TV/AV V- V+ P- P+
Voltage 0 0.4125 0.825 1.2375 1.65 2.0625 2.475

Function POWER MENU TV/AV V- V+ P- P+
Voltage 2.2 1.75 0.85 1.3 0.4 0.0



13

Press[3]/[4] keys: The LOGO level position adjust, [3] is to the left adjustment, [4] rightwards adjusts;
Press[5]/[6] keys: The color choice of the LOGO character list, [5] regulate the first color, [6] regulate the
second color;
Press[7]/[8] keys: The LOGO character list size adjust, [7] regulate the first size, [8] regulate the second size;
Press[0] keys:Delete the letter of alphabet of importation

Press[(]/[(]key: The LOGO character list choose(0~9;A~Z;a~z; ":.+-*/@", SPACE);
Press[(]/[(]key: Move cursor;
Press[REVIEW]key: Withdraw LOGO editor appearance, the LOGO information remembers EEPROM and
return to M_MODE;

5. The ZOOM adjust.
At the M_MODE, press[ZOOM]key: Press when screen showed "ZOOM" or"16:9"[VOL+]/[VOL-]the key
regulated ZOOM/16:9 of field.




ICs functional description
UOC TDA11105-XXXX/TDA11106-XXXX
SYMBOL PIN DESCRIPTION
IF VO 1 IF video output / selected CVBS output
VP2 2 2
ND
Supply voltage TV processor(+5v)
VCC AUDIO 3 8 volt supply for audio switches(+5V~8V)
PLL IF 4 IF-PLL loop filter
GND2 5 Gaound 2 for TV processor
DECSDEM 6 decoupling sound demodulator or SIF input 2
FMDEMOUT 7 audio output /AM audio output (volume controlled)
EHTO 8 EHT/overvoltage protection input
AGC 9 Tuner AGC output
IREF 10 Reference current input
VSC 11 Vertical sawtooth capacitor
IF IN2 12 IF input 1
IF IN1 13 IF input 2
VDRA 14 Vertical drive A output
VDRB 15 Vertical drive B output
AVL/EW 16 Automatic volume leveling /EAST-WEST drive output
DECBG 17 Band gap decoupling
SECPLL 18 SECAM PLL decoupling
GND1 19 Ground 1 for TV-processor
PH1LF 20 Phase-1 filter
PH2LF 21 Phase-2 filter
VP1 22 1
st
supply voltage TV-processor(+5V)


14

DECDIG 23 decoupling digital supply of TV-processor
XTALOUT 24 crystal oscillator output
XTALIN 25 crystal oscillator input
IR 26 Remote control signal input.
MUTE 27 Sound mute output
TILT/UHF 28
KEY 29 Control keys input *3
BAND2 30 Tuner Band selection output
BAND1 31 Tuner Band selection output
TUNING 32 tuning Voltage (Vt) PWM output
VDDP 33 Supply to periphery-3.3V)
SDA 34 I
2
C-bus data line


SCL 35 I
2
C-bus clock line
AV1 36 TV/AV (AV1) / AV2 mode Control Output.
AV2 37 TV/AV (AV1) / AV2 mode Control Output.
STANDBY 38 In STAND BY mode, high level (Power OFF).For Power ON this pin will
be reduced to low.
50/60 39
VDDC 40 Supply(3.3V)
GND5 41 Ground 5
VPE 42 OPT programming Voltage
VDDA 43 Supply voltage(3.3V)
BOUT 44 Blue output
GOUT 45 Green output
ROUT 46 Red output
BLKIN 47 black current input / V-guard input
BCL IN 48 beam current limiter input
PB 49 B input / U (B-Y) input / PB input
Y3/CVBS3 50 G input / Y input
PR/C3 51 R input / V (R-Y) input / PR input
YOUT 52 Y-output(for YUV interface)
Y SYNC 53 Y-input for sync separator
VP3 54 Supply voltage(5V)
GND3 55 Ground connection
HOUT 56 Horizontal output
FBISO 57 Flyback input/sandcastle output
LSR 58 Audio output R
LSL 59 Audio output L
C2/C3/C4/AIN5R 60 S-VIDEO C IN
AIN3/IN1R 61 R AUDIO IN
CVBS2/Y2 62 AV2 VIDEO IN


15

AIN2/1INL 63 L AUDIO IN
CVBS/Y4/AIN5L 64 AV1 VIDEO IN

AN7522/AN17821/AN7523/AN17823 Function : audio output
Symbol PIN Function Symbol PIN Function
Vcc 1 Power supply GND 7 ground
Out 1 (+) 2 Ch 1 output (+) In 2 8 Ch 2 input
GND(out 1) 3 Ch 1Ground VOL 9 Volume Control
Out 1 (-) 4 Ch 1 output (-) Out 2 (-) 10 Ch 2 output (-)
Standby 5 Mute input GND(out 2) 11 Ch 2 Ground
In 1 6 Ch 1 input Out 2 (+) 12 Ch 2 output (+)
Note: AN7523 is pin 1 to 9, AN7522 is pin 1 to 12.






LA9302A/8177/LA78041/LA78040/STV9325/STV9378 Function : vertical output
Symbol PIN Function Symbol PIN Function
INV IN 1 Input V OUT 5 Vertical output
VCC1 2 Power VCC2 6 Output power supply
PUMP UP 3 Pump up power NON INV IN 7 Negative feedback
GND 4 Ground

Test point Waveforms

















V451 C
5Vpp 0.9Vpp
1000Vpp
1.3Vpp
H
H
1Vpp
V
H H

CRT KB CRT KG CRT KR
95Vpp 95Vpp 95Vpp
H
H H
V451 B
2.7Vpp

TDA11105 PIN45
2.5Vpp 2.5Vpp 3.8Vpp
H H
H
TDA11105 PIN44 TDA11105 PIN46
TDA11105 PIN56 TDA11105 PIN57
0.8Vpp
V
TDA11105 PIN14 TDA11105 PIN15
TDA11105 PIN24
1.2Vpp 2.6Vpp
H H
TDA11105 PIN52
TDA11105 PIN1


16








TDA8177 / STv9302/ LA78040 or LA78041/`STV9325/STV9378
PIN 1 2 3 4 5 6 7
V 0.7 15 -12 -15 0.3 15.9 -0.07


AN 7522/AN17821 (Note: AN7523 is pin 1 to 9, AN7522 is pin 1 to 12.)
PIN 1 2 3 4 5 6 7 8 9 10 11 12
V 12 7 0 7 3.3 1.4 0 1.4 0 7 0 7



PURITY / CONVERGENCE ADJUSTMENT

T511 PIN7 HEATER
300Vpp 22Vpp
H H


17

PURITY ADJUSTMENT

1. Demagnetize CRT with the demagnetizer.

2. Loosen the retainer screw of the deflection yoke.

3. Remove the wedges.

4. Input a green raster signal from the signal generator,
and turn the screen to green raster.

5. Move the deflection yoke backward.

6. Bring the long lug of the purity magnets on the short
lug and position them horizontally. (Fig2)

7. Adjust the gap between two lugs so that the GREEN
RASTER will come into the center of the screen. (Fig.
3)

8. Move the deflection yoke forward, and fix the position
of the deflection yoke so that the whole screen will
become green.

9. Insert the wedge to the top side of the deflection yoke
so that it will not move.

10. Imput a crosshatch signal.

11. Verify that the screen is horizontal.

12. Input red and blue raster signals, and make sure that
purity is properly adjusted.


CRT
WEDGE
DEFLECTION YOKE
P


4 6
P: PURITY MAGNET
4: 4-POLES (convergence magnets)
6: 6-POLES (convergence magnets)
P/C MAGNETS
Fig. 1
PURITY MAGNETS
Long lug



Short lug
Bring the long lug over the short lug
and position them horizontally.
Fig. 2
(FRONT VIEW)
GREEN RASTER
CENTER
Fig. 3


18

STATIC CONVERGENCE ADJUSTMENT

1. Input a crosshatch signal.

2. Using 4-pole convergence magnets, overlap the red
and blue lines in the center of the screen (Fig. 1) and
turn them to magenta (red/blue).

3. Using 6-pole convergence magnets, overlap the
magenta (red/blue) and green lines in the center of the
screen and turn them to white.

4. Repeat 2 and 3 above, and make the best
convergence.



DYNAMIC CONVERGENCE ADJUSTMENT

1. Move the deflection yoke up and down and overlap
lines in the periphery. (Fig. 2)

2. Move the deflection yoke left to right and overlap the
lines in the periphery. (Fig. 3)

3. Repeat 1 and 2 above, and make the best
convergence.







After adjustment, fix the wedge at the original position.
Fasten the retainer screw of the deflection yoke.
Fix the 6 magnets with glue.


(FRONT VIEW)
Fig. 1
(FRONT VIEW)
RED GREEN BLUE

BLUE
RED
GREEN GREEN
RED BLUE


BLUE GREEN RED
Fig.2
(FRONT VIEW)
RED GREEN BLUE BLUE GREEN RED
RED

GREEN
BLUE


BLUE

GREEN
RED
\O. l^kT \O. \^Ml SllCTlTC^TTO\ DlSCkTlTTO\ |\TT
O|^
\TT
TY
l^kT l^Cl
bO^kD
l^Cl
! ?8lCbl|00?!0 M^T\ lCb CYl|TOl lCS !
? !000?+C08000 TC ^T?+C08 lCS ! \0! M^T\
3 !000!!!0000 TC \T!!!3blC30l0 lCS ! \?0! M^T\
+ !00000+l0 TC |lC+l^33\ blT lCS ! \b! M^T\
!0000+0?000 TC TC+0?|Cl+0?bl lCS ! \80! M^T\
b !00080+!000 TC ^8!+!ST\8!? lCS ! \30! M^T\
!000008!000 TC lC8!bT\8!l8! lCS ! \0! M^T\
8 !000!8?!000 TC ^\!8?!^^\?? lCS ! \b0! M^T\
9 !!?SC380l00 Tk^\STSTOk ?SC380 lCS ! \0? M^T\
!0 !!?SC?9bl00 Tk^\STSTOk D03b?SC?9b lCS ! \+! M^T\
!! !!?SC?99l00 Tk^\STSTOk ?SC++b0 lCS ! \!3 M^T\
!? !!?SC?383l0 Tk^\STSTOk ?SC?383 blT lCS 3 \+0!\b+\b M^T\
!3 !!0?Sbb+l0 Tk^\STSTOk ?Sbb+ blT lCS ! \0! M^T\
!+ !!?SC!8!l0 Tk^\STSTOk ?SC!8!Y blT lCS 8
\?\b!\b?\b0?\0?\
80!\80?\3!!
M^T\
! !!?S^!0!l0 Tk^\STSTOk ?S^!0!Y blT lCS 3 \b3\b0!\803 M^T\
!b !!?SC!b+l0 Tk^\STSTOk ?SC!b+ blT lCS ! \!0! M^T\
!8 !!?SD?0!?l00 Tk^\STSTOk ^9+0 lCS ! \303^ M^T\
!9 !?0T\+!+8l? S"TTC|T\0 DTODl T\+!+8 blT lCS !0
D?0!D?0D+0+D+b!D08D
!!D!?DbbD0!Db03
M^T\
?0 !?00k?0l? S"TTC|T\0 DTODl T\399k?0 blT lCS + D0!D0?D03D0+ M^T\
?! !?00lk!0l? S"TTC|T\0 DTODl lk!0lk! blT lCS ? D30!D+0! M^T\
?? !?00lk!+l? S"TTC|T\0 DTODl lk!+ blT lCS ? D0bD+b? M^T\
?3 !?00lk?0+!? S"TTC|T\0 DTODl lk?0+ !?.mm lCS ! D3 M^T\
?+ !?00lk30!? S"TTC|T\0 DTODl lk30 !?.mm lCS ? DbD+? M^T\
? !?00lk309!? S"TTC|T\0 DTODl lk309 !?.mm lCS ! D+! M^T\
?b !?0|lk?0+!? S"TTC|T\0 DTODl |lk?0+ !?.mm lCS 3 D?D+D M^T\
? !?0|lk308!? S"TTC|T\0 DTODl k|+^M !?.mm lCS ! D! M^T\
?8 !?03C?3\3l? /l\lk DTODl 3.3\3C? blT lCS ! D03 M^T\
?9 !?0C?\!l? /l\lk DTODl .!\C? blT lCS ? D80!D80? M^T\
30 !?0b^?\bl? /l\lk DTODl .b\b^?bb! blT lCS ? DbDb+ M^T\
3! !?0bC3b\3l? /l\lk DTODl b.?\bC3 blT lCS ! D M^T\
3? !?0C?\l? /l\lk DTODl 9C!9.!\ blT lCS ! D! M^T\
33 !?09^?8\?l? /l\lk DTODl 8.?\9^? blT lCS + D+0?D?0?D?03D?0+ M^T\
3+ !?09b?9\!l? /l\lk DTODl 9.!\9C? blT lCS ! Db! M^T\
3 !bkTl330|l? C^kbO\ lTM klSTSTOk kT!b"33'| ?bmm blT lCS ! ?0! M^T\
?!?|S?!?8|S Mu`u bOM ?0!00?!
3b !bkTl390|l? C^kbO\ lTM klSTSTOk kT!b"39'| ?bmm blT lCS ! k!03 M^T\
3 !bkTlb0|l? C^kbO\ lTM klSTSTOk kT!b"b'| ?bmm blT lCS ! k838 M^T\
38 !bkTl!0!|l? C^kbO\ lTM klSTSTOk kT!b"!00'| ?bmm blT lCS !
k!!0k!!!k?08k?09k?!0k
?!?k30bk30k!0k!!k
!?k!+k!k8?+k8?k8?
bk83?
M^T\
39 !bkTl??!|l? C^kbO\ lTM klSTSTOk kT!b"??0'| ?bmm blT lCS 3 k!0!k80bk309 M^T\
+! !bkTl39!|l? C^kbO\ lTM klSTSTOk kT!b"390'| ?bmm blT lCS ! k?0! M^T\
+? !bkTl+!|l? C^kbO\ lTM klSTSTOk kT!b"+0'| ?bmm blT lCS 3 k!0?k80k3!? M^T\
+3 !bkTlb8!|l? C^kbO\ lTM klSTSTOk kT!b"b80'| ?bmm blT lCS ? k?0?k!3 M^T\
++ !bkTl!0?|l? C^kbO\ lTM klSTSTOk kT!b"!l'| ?bmm blT lCS 8
k3k803k80k8!bk8!8k
8?0k8??k0!
M^T\
+ !bkTl!??|l? C^kbO\ lTM klSTSTOk kT!b"!.?l'| ?bmm blT lCS ! k!0 M^T\
+b !bkTl!8?|l? C^kbO\ lTM klSTSTOk kT!b"!.8l'| ?bmm blT lCS ? k30!k303 M^T\
+ !bkTl?+?|l? C^kbO\ lTM klSTSTOk kT!b"!.l'| ?bmm blT lCS ! k!0 M^T\
+8 !bkTl??|l? C^kbO\ lTM klSTSTOk kT!b"?.l'| ?bmm blT lCS ! k0b M^T\
+9 !bkTl33?|l? C^kbO\ lTM klSTSTOk kT!b"3.3l'| ?bmm blT lCS 3 k!bk03k0+ M^T\
0 !bkTl+?|l? C^kbO\ lTM klSTSTOk kT!b"+.l'| ?bmm blT lCS !?
k!0+k?!3kb09kb!0k0k
09k!8k!9k?!k?k
?8k3!!
M^T\
! !bkTlb?|l? C^kbO\ lTM klSTSTOk kT!b".bl'| ?bmm blT lCS ? k0k9 M^T\
? !bkTl?|l? C^kbO\ lTM klSTSTOk kT!b".l'| ?bmm blT lCS ! k?! M^T\
3 !bkTl8??|l? C^kbO\ lTM klSTSTOk kT!b"8.?l'| ?bmm blT lCS ! k!08 M^T\
+ !bkTl!03|l? C^kbO\ lTM klSTSTOk kT!b"!0l'| ?bmm blT lCS ?0
k!09k+0?kbkb0?kb!!k
b!?kb!+k0?k0k?3k
?k?bk8!!k8!?k8!k8!
k8?!k83bk?!bDb00
M^T\
!bkTl!?3|l? C^kbO\ lTM klSTSTOk kT!b"!?l'| ?bmm blT lCS ! k?0 M^T\
b !bkTl!3|l? C^kbO\ lTM klSTSTOk kT!b"!l'| ?bmm blT lCS ! k09 M^T\
!bkTl??3|l? C^kbO\ lTM klSTSTOk kT!b"??l'| ?bmm blT lCS 3 k!k0bk+ M^T\
8 !bkTl?3|l? C^kbO\ lTM klSTSTOk kT!b"?l'| ?bmm blT lCS ? k08kb0b M^T\
9 !bkTl393|l? C^kbO\ lTM klSTSTOk kT!b"39l'| ?bmm blT lCS ! k?0b M^T\
b0 !bkTl+3|l? C^kbO\ lTM klSTSTOk kT!b"+l'| ?bmm blT lCS ! k!0b M^T\
b! !bkTlb83|l? C^kbO\ lTM klSTSTOk kT!b"b8l'| ?bmm blT lCS ! kb03 M^T\
b? !bkTl!0+|l? C^kbO\ lTM klSTSTOk kT!b"!00l'| ?bmm blT lCS b
kb0+k80?k83k3!3kb0k
!b
M^T\
b3 !bkT0!0^|l? C^kbO\ lTM klSTSTOk kT!+"!'| ?bmm blT lCS ! k30? M^T\
b+ !bkT0??0|l? C^kbO\ lTM klSTSTOk kT!+"??'| ?bmm blT lCS ! k!! M^T\
b !bkT0?0|l? C^kbO\ lTM klSTSTOk kT!+"?'| ?bmm blT lCS ! k?0 M^T\
b !bkT0!!|l? C^kbO\ lTM klSTSTOk kT!+"!0'| ?bmm blT lCS ? kkb? M^T\
b8 !bkT0!0?|l? C^kbO\ lTM klSTSTOk kT!+"!l'| ?bmm blT lCS ! k+ M^T\
b9 !bkT0+?|l? C^kbO\ lTM klSTSTOk kT!+"+.l'| ?bmm blT lCS ! k+0 M^T\
0 !bkT0??+|l? C^kbO\ lTM klSTSTOk kT!+"??0l'| ?bmm blT lCS ! k+0! M^T\
! !bkT|??!|l? C^kbO\ lTM klSTSTOk kT!?"??0'| blT lCS ! kb+ M^T\
? !bkT|!0?|l? C^kbO\ lTM klSTSTOk kT!?"!l'| blT lCS ! k+03 M^T\
3 !bkT|??3|l? C^kbO\ lTM klSTSTOk kY!"+l'|lOkMT\0) blT lCS ! k+8 M^T\
+ !bkT|!?bll?
|T0| \OT^0l T\S|^TlD
klSTS.
kT+0!?"!?M'l blT lCS ! k!+ M^T\
!bkY|?^|l? MlT^ O\TDl lTM klSTSTOk kY!?"??'| blT lCS ! kb0 M^T\
b !bkY|!0+|l? MlT^ O\TDl lTM klSTSTOk kY!?"!00l'| blT lCS ! k M^T\
!bkY|!?+|l? MlT^ O\TDl lTM klSTSTOk kY!?"!?0l'| blT lCS ? k03k0+ M^T\
8 !bkY|!+|l? MlT^ O\TDl lTM klSTSTOk kY!?"!0l'| blT lCS ! k M^T\
9 !bkYT0+|! MlT^ O\TDl lTM klSTSTOk kY!"0.+'| !mm lCS ! kb8 M^T\
80 !bkYT!^|! MlT^ O\TDl lTM klSTSTOk kY!".!'| !mm lCS ! k3! M^T\
8! !bkYT+3|! MlT^ O\TDl lTM klSTSTOk kY!?"+l'| !mm lCS ! k0 M^T\
8? !bkY|0+|?0 MlT^ O\TDl lTM klSTSTOk kY?"0.+'| ?0mm lCS ! kb0! M^T\
83 !bkY|!0^|?0 MlT^ O\TDl lTM klSTSTOk kY?"!'| ?0mm lCS ! kb! M^T\
8+ !bkY|+^|?0 MlT^ O\TDl lTM klSTSTOk kY?"+.'| ?0mm lCS ! kb M^T\
8 !bkY|8?^|?0 MlT^ O\TDl lTM klSTSTOk kY?"8.?'| ?0mm lCS ! k! M^T\
8b !bkY|b80|?0 MlT^ O\TDl lTM klSTSTOk kY?"b8'| ?0mm lCS ! k!? M^T\
8 !bkY|?!|?0 MlT^ O\TDl lTM klSTSTOk kY?"?0'| ?0mm lCS ! k++ M^T\
88 !bkY|!3|?0 MlT^ O\TDl lTM klSTSTOk kY?"!l'| ?0mm lCS ! kb9 M^T\
89 !bk\33^|000 Ok0^\TC SOTD klSTSTOk kY?"+'| lCS ! k!3 M^T\
90 !bMl?!!|000 T|lkMTSTOk T|lkMTSTOk Ml?8D!! lCS ! k0? M^T\
9! !bkM39^|000 Dl0^|SST\0 T|lkMTSTOk M/3b9'3`u) lCS ! kT0! M^T\
9? !bk"0?l?|000 TkTMMlk lOTl\TTOMlTlk "?0b?^?l'l lCS ! kl! M^T\
93 !?l|??!|l0 Clk^MTC C^l^CTTOk CT!k|b3\??0l| blT lCS 3 C3!3C0?C03 M^T\
9 !?l|!0?|l0 Clk^MTC C^l^CTTOk CT!?bb3\!000l| blT lCS C?0?C?03C?0C?!3C?!+ M^T\
9b !?l|!03/l0 Clk^MTC C^l^CTTOk CT!?lb3\0.0!l/ blT lCS 9
C!0+C!0C!0bC?!bCb9C
b0+Cb0bC0!C!!
M^T\
9 !?l|!0+|l0 Clk^MTC C^l^CTTOk CT!?lb3\0.!ll blT lCS C??0C???C??3C0C!3 M^T\
98 !?bk!0?ll0 Clk^MTC C^l^CTTOk CT8!?b00\!000ll blT lCS ! C+? M^T\
99 !?bk39?ll0 Clk^MTC C^l^CTTOk CT8!?b00\3900ll blT lCS ! C+! M^T\
!00 !?bk+?ll0 Clk^MTC C^l^CTTOk CT8!?b00\+00ll blT lCS ! C+b! M^T\
!0! !?bT!0?l!0 Clk^MTC C^l^CTTOk CT8!?b!l\!000ll lCS 3 C0+C0Cb? M^T\
!0? !?bT+!l Clk^MTC C^l^CTTOk CT8!?b!l\+0ll lCS ! C3 M^T\
!03 !?b\b8!l Clk^MTC C^l^CTTOk CT8!?b?l\b80ll lCS ? C!3^C?! M^T\
!0 !^Cl???M!0 Clk^MTC C^l^CTTOk CT?l++00\^C??00lM lCS ! C! M^T\
!0b !00l+?ll0 T\D|CT\l lOY.C^l^CTTOk C!!!00\0.0!l| blT lCS ! C?? M^T\
!0 !00lb8?ll0 T\D|CT\l lOY.C^l^CTTOk C!!!00\b800l| blT lCS ! C?! M^T\
!08 !00l!3ll0 T\D|CT\l lOY.C^l^CTTOk C!!!00\0.0!l| blT lCS ! C08 M^T\
!09 !00l333ll0 T\D|CT\l lOY.C^l^CTTOk C!!!00\0.033l| blT lCS ? C30!C30b M^T\
!!0 !00l+3ll0 T\D|CT\l lOY.C^l^CTTOk C!!!00\0.0+l| blT lCS ? C30?C3!0 M^T\
!!! !00l!0+ll0 T\D|CT\l lOY.C^l^CTTOk C!!!00\0.!l| blT lCS 8
C?0!C?09C303C+8C!+C
0+C0C0b
M^T\
!!? !??S!3ll0 MlT^T/lD lOY.C^l^CTTOk C?!\!00\0.0!l| blT lCS ! C09 M^T\
!!3 !??S!0+ll0 MlT^T/lD lOY.C^l^CTTOk C?!\!00\0.!l| blT lCS ! C?0 M^T\
!!+ !0^\!0+M! MlT^T/lD lOY.C^l^CTTOk
Cbb?3^?\^C0.!lMCTS
?0^C0.!lM
lCS ! C0! M^T\
!! !00l+^Ml0 MT\T llC.C^l^CTTOk CD!!0!b\+.lM blT lCS ! C!08 M^T\
!!b !00l!00Ml0 MT\T llC.C^l^CTTOk CD!!0!b\!0lM blT lCS !8
C!0!C!0?C!03C?!C08C
!0C80!C80?C80+C80C8
0bC80C808C809C8!3C8!
+C8!C8!b
M^T\
!! !00l??0Ml0 MT\T llC.C^l^CTTOk CD!!0!b\??lM blT lCS ? C??!Cb0 M^T\
!!8 !00l+0Ml0 MT\T llC.C^l^CTTOk CD!!0!b\+lM blT lCS b
Cb3Cb+CbC09C!?C
b09
M^T\
!!9 !00l!0!Ml0 MT\T llC.C^l^CTTOk CD!!0!b\!00lM blT lCS C?08C?!!C?!9C??+Cb8 M^T\
!?0 !00l??!Ml0 MT\T llC.C^l^CTTOk CD!!0!b\??0lM blT lCS ! C803 M^T\
!?! !00l+!Ml0 MT\T llC.C^l^CTTOk CD!!0!b\+0lM blT lCS 3 CbbCbCb0! M^T\
!?? !00l!00Ml00 MT\T llC.C^l^CTTOk CD!!0?\!0lM blT lCS ! C?0+ M^T\
!?3 !00|+!Ml00 MT\T llC.C^l^CTTOk CD?88| !b\+0l blT lCS ? CCb M^T\
!?+ !00l+!Ml00 MT\T llC.C^l^CTTOk CD?88| ?\+0l lCS ? C3!+C3! M^T\
!? !000+0Ml0 MT\T llC.C^l^CTTOk CD!!03\+lM blT lCS ! C+0! M^T\
!?b !000!0!Ml0 MT\T llC.C^l^CTTOk CD?88|3\!00l blT lCS ! C30+ M^T\
!? !000??!Ml00 MT\T llC.C^l^CTTOk CD?88|3\??0l lCS ! C30 M^T\
!?8 !00T0+Ml0 MT\T llC.C^l^CTTOk CD!!00\0.+lM blT lCS 3 Cb03Cb0Cb08 M^T\
!?9 !00T!0^Ml0 MT\T llC.C^l^CTTOk CD!!00\!lM blT lCS 3 C?!8C8!0C8!! M^T\
!30 !00T+^Ml0 MT\T llC.C^l^CTTOk CD!!00\+.lM blT lCS ! Cb! M^T\
!3! !00M+0MlO0 MT\T llC.C^l^CTTOk CD?88|!b0\+lM blT lCS ! C+03 M^T\
!3? !00M!0!MlO0 MT\T llC.C^l^CTTOk CD?88|!b0\!00lM lCS ! C! M^T\
!33 !00M+^MlO0 MT\T llC.C^l^CTTOk CD?88|!b0\+.lM lCS ! C+9 M^T\
!3+ !00O!00MlO0 MT\T llC.C^l^CTTOk CD?88|?0\!0lM lCS ! C+0? M^T\
!3 !00l??!M000 MT\T llC.C^l^CTTOk CD?93+00\!00lM lCS ! C0 M^T\
!3b !00T!00Ml00 MT\T llC.C^l^CTTOk CDS 0\+.l lCS ! C3!? M^T\
!3 !930!?^ll? T\D|CTOk "TT| COOk CTDlS 0030!.?|l blT lCS ! !0! M^T\
!38 !930!00ll? T\D|CTOk "TT| COOk CTDlS 0030!0|l blT lCS b
?0??030!0?03
0+
M^T\
!39 ?0!8?bb00000 |OkT/O\T^ T\l^kTTY COT |CYDDb00| lCS ! 3!! M^T\
!+0 ?+?+b00000 O|^kT/ \?+.bM lCS ! 00! M^T\
!+! ?3l\l03000 T|\lk D"l03\8 lCS ! ^!0! M^T\
!+? ?0bCl!899000
S"TTC|T\0 lO"lk
Tk^\SlOkMlk
YbC+0!9?9?! lCS ! T0! M^T\
!+3 ?00||l!!9000
|OkT/O\T^ DkT\l
Tk^\SlOkMlk
|bC!8+lT!9YDDlT!9 lCS ! T+! M^T\
!++ ?0000lT?+000 llO"lk lTTlk Tk^\SlOkMlk YDD|l!b lCS ! 0! M^T\
!+ ?+0lD\380000 Tl lTTlk l38.0|b\38.0| lCS ! /!0! M^T\
!+b ?00b\0|!000 l|Sl bk^CllT b\0|! lCS ? l|0! M^T\
!+ ??0\3!000 l|Sl T3.!^?0\^C lCS ! l|0! M^T\
!+9 ?|!00D?000 lkT| CO\\lCTOk C|!0?DY lCS ? \S0!\S0? M^T\
!0 ?C|bD0000 lkT| CO\\lCTOk C|bDY) lCS ! \S+0? M^T\
!! ?b0?D?000 lkT| CO\\lCTOk C|b?.?DY lCS 3 \Sb0!\Sb0?\S0? M^T\
!? ?b0?D+000 lkT| CO\\lCTOk C|b?.+DY lCS 3 \S03\S0+\S80+\S+03 M^T\
!3 ?b0?D000 lkT| CO\\lCTOk C|b?.DY lCS ! \S?0! M^T\
!b ?00^\b!+000 b^\ TTl |^Cl ^\b!+ lCS ! \S80! M^T\
! 3?00|3+!0000 |l^T ST\lTC.\lkTTC^) |3+!0C lCS ! \30!\+! M^T\
!8 3?00D?3+000 |l^T ST\llO"lk) D!+?! lCS ! \!3 M^T\
!9 3?00/?3+000 |l^T ST\l /?3+ lCS ! \303^ M^T\
!b0 3?0!8?!M000 |l^T ST\l^|DTO) !8?!M lCS ! \b0! M^T\
!b! +3!!0?030000 kT\lT ?.0 \ 3.0MM lCS ? ++! M^T\
!b? +3!!0308?000 SCkl" lOk |l^T ST\l M 3`8 lCS 3 \30!\b0!?) M^T\
!b3 +3!!03!0?000 SCkl" lOk |l^T ST\l M 3`!0 lCS ? \!3\+! M^T\
!b+ +3!!03!0?000 SCkl" lOk |l^T ST\l Tk 3`!0 lCS ! \303^ M^T\
!b +3!30000000 \|T lOk |l^T ST\l M3 lCS \30!\+!\!3\b0!?) M^T\
!bb ||Mllk mm lCS 3 "b08"!8"3!? M^T\
!b ||Mllk .mm lCS 30
"!0!"?0!"?0?"?0"?08"
?09"?!0"?!?"03"08"
!!"?"08"!0"!3"80
!"?!3"b0bk?0"?!+"?!b
"!?"!3"80"?0b"?03
"3!+k3!9k3??k3!b
M^T\
!b8 ||Mllk !0mm lCS ?3
"+0+"0"0b"09"!0"
b3"9!"b0"0!"0?"
0+"!?"80?"803"80+"80
"80b"30!"30?"90"3
"?!!"3!0
M^T\
!b9 ||Mllk !?.mm lCS 9
"0?"?0"?0+"!"b!"
93"09"!++03
M^T\
!0 ||Mllk !mm lCS ? 30!"! M^T\
\O. l^kT \O. SllCTlTC^TTO\ \^Ml DlSCkTlTTO\ |\TT
O|^
\TT
TY
l^kT l^Cl
bO^kD
l^Cl
! !bkTl+?|l? C^kbO\ lTM klSTSTOk kT!b".!l'| ?bmm blT lCS ! k+!+ M^T\
? !bkYT!0^|! MlT^ O\TDl lTM klSTSTOk kY!"!.'| !mm lCS ? k30+k30+^ M^T\
3 !bkYT!8!|! MlT^ O\TDl lTM klSTSTOk kY!"330'| !mm lCS ! k30 M^T\
+ !bkYT!0?|! MlT^ O\TDl lTM klSTSTOk kY!"?.l'| !mm lCS ! k+0+ M^T\
CkT l^k^MlTlk
?!|S T|OMSO\ ^!lM"03?\0^!
!bkl|33^|?0 MlT^ O\TDl lTM klSTSTOk kl!0?"!.'| ?0mm lCS ! k+! M^T\
b ?0|!?830000 |OkT/O\T^ T\l^kTTY COT +0|) lCS ! ++! M^T\
!??l3b+l! MlT^T/lD lOY.C^l^CTTOk Cbb?!?0\0.3bl| lCS ! C+b0 M^T\
8 !??l333l! MlT^T/lD lOY.C^l^CTTOk Cbb?!b30\0.033l| lCS ! C+ M^T\
9 !8!|???|?0 MlT^T/lD lOY.C^l^CTTOk Cbb8!!.bl\3300l| lCS ! C++ M^T\
!0 !8!|b??|?0 MlT^T/lD lOY.C^l^CTTOk Cbb8!!.bl\b?00ll| lCS ! C+ M^T\
!! !8!|?|?0 MlT^T/lD lOY.C^l^CTTOk Cbb8!!.bl\9!00ll| lCS ! C+b M^T\
!? !80\0!??/000 lYb^Cl Tk^\SlOkMlk bSC?\0b08 lCS ! T+0! M^T\
!3 ?|!00D!000 lkT| CO\\lCTOk C|b!DY lCS ! lbT \O.? M^T\
!
\O. \O. \O. \O. l^kT \O. l^kT \O. l^kT \O. l^kT \O. \^Ml \^Ml \^Ml \^Ml SllCTlTC^TTO\ SllCTlTC^TTO\ SllCTlTC^TTO\ SllCTlTC^TTO\ DlSCkTlTTO\ DlSCkTlTTO\ DlSCkTlTTO\ DlSCkTlTTO\ |\TT |\TT |\TT |\TT
O|^ O|^ O|^ O|^
\TT \TT \TT \TT
TY TY TY TY
TOT^ ^MO|\T TOT^ ^MO|\T TOT^ ^MO|\T TOT^ ^MO|\T
l^kT l^kT l^kT l^kT
l^Cl l^Cl l^Cl l^Cl
! !! ! ||Mllk ||Mllk ||Mllk ||Mllk .mm .mm .mm .mm lCS lCS lCS lCS ! !! ! "90! "90! "90! "90! CkT CkT CkT CkT
? ?? ? ?8lCbl|00?!0 ?8lCbl|00?!0 ?8lCbl|00?!0 ?8lCbl|00?!0 M^T\ lCb M^T\ lCb M^T\ lCb M^T\ lCb CYl| CYl| CYl| CYl| TOlCkT) TOlCkT) TOlCkT) TOlCkT) lCS lCS lCS lCS ! !! !
3 33 3 !?0T\+!+8l? !?0T\+!+8l? !?0T\+!+8l? !?0T\+!+8l? S"TTC|T\0 DTODl S"TTC|T\0 DTODl S"TTC|T\0 DTODl S"TTC|T\0 DTODl T\+!+8 T\+!+8 T\+!+8 T\+!+8 blT lCS lCS lCS lCS ! !! ! D933 D933 D933 D933 CkT CkT CkT CkT
+ ++ + !!?SC!8!l0 !!?SC!8!l0 !!?SC!8!l0 !!?SC!8!l0 Tk^\STSTOk Tk^\STSTOk Tk^\STSTOk Tk^\STSTOk ?SC!8!Y ?SC!8!Y ?SC!8!Y ?SC!8!Y blT lCS lCS lCS lCS 3 33 3 \90! \90! \90! \90! \9!! \9!! \9!! \9!! \9?! \9?! \9?! \9?! CkT CkT CkT CkT
!!?SC?+8?l0 !!?SC?+8?l0 !!?SC?+8?l0 !!?SC?+8?l0 Tk^\STSTOk Tk^\STSTOk Tk^\STSTOk Tk^\STSTOk ?SC?+8? ?SC?+8? ?SC?+8? ?SC?+8? blT lCS lCS lCS lCS 3 33 3 \9!? \9!? \9!? \9!? \9?? \9?? \9?? \9?? \9?3 \9?3 \9?3 \9?3 CkT CkT CkT CkT
b bb b !bkTl!0!|l? !bkTl!0!|l? !bkTl!0!|l? !bkTl!0!|l? C^kbO\ lTM klSTSTOk C^kbO\ lTM klSTSTOk C^kbO\ lTM klSTSTOk C^kbO\ lTM klSTSTOk kT!b"!00'| kT!b"!00'| kT!b"!00'| kT!b"!00'| blT lCS lCS lCS lCS 3 33 3 k90! k90! k90! k90! k9!! k9!! k9!! k9!! k9?! k9?! k9?! k9?! CkT CkT CkT CkT
!bkTl30!|l? !bkTl30!|l? !bkTl30!|l? !bkTl30!|l? C^kbO\ lTM klSTSTOk C^kbO\ lTM klSTSTOk C^kbO\ lTM klSTSTOk C^kbO\ lTM klSTSTOk kT!b"300'| kT!b"300'| kT!b"300'| kT!b"300'| blT lCS lCS lCS lCS 3 33 3 k903 k903 k903 k903 k9!3 k9!3 k9!3 k9!3 k9?? k9?? k9?? k9?? CkT CkT CkT CkT
8 88 8 !bkT0330|l? !bkT0330|l? !bkT0330|l? !bkT0330|l? C^kbO\ lTM klSTSTOk C^kbO\ lTM klSTSTOk C^kbO\ lTM klSTSTOk C^kbO\ lTM klSTSTOk kT!+"33'| kT!+"33'| kT!+"33'| kT!+"33'| blT lCS lCS lCS lCS ! !! ! k93? k93? k93? k93? CkT CkT CkT CkT
9 99 9 !bkT|!0?|l? !bkT|!0?|l? !bkT|!0?|l? !bkT|!0?|l? C^kbO\ lTM klSTSTOk C^kbO\ lTM klSTSTOk C^kbO\ lTM klSTSTOk C^kbO\ lTM klSTSTOk kT!?"!l'| kT!?"!l'| kT!?"!l'| kT!?"!l'| blT lCS lCS lCS lCS 3 33 3 k90+ k90+ k90+ k90+ k9!+ k9!+ k9!+ k9!+ k9?+ k9?+ k9?+ k9?+ CkT CkT CkT CkT
!0 !0 !0 !0 !bkY|!3|?0 !bkY|!3|?0 !bkY|!3|?0 !bkY|!3|?0 MlT^ O\TDl lTM klSTSTOk MlT^ O\TDl lTM klSTSTOk MlT^ O\TDl lTM klSTSTOk MlT^ O\TDl lTM klSTSTOk kY?"!l'| kY?"!l'| kY?"!l'| kY?"!l'| ?0mm ?0mm ?0mm ?0mm lCS lCS lCS lCS 3 33 3 k90b k90b k90b k90b k9!b k9!b k9!b k9!b k9?b k9?b k9?b k9?b CkT CkT CkT CkT
!! !! !! !! !?l|b8!|l0 !?l|b8!|l0 !?l|b8!|l0 !?l|b8!|l0 Clk^MTC C^l^CTTOk Clk^MTC C^l^CTTOk Clk^MTC C^l^CTTOk Clk^MTC C^l^CTTOk CT!?b+b3\b80l| CT!?b+b3\b80l| CT!?b+b3\b80l| CT!?b+b3\b80l| blT lCS lCS lCS lCS 3 33 3 C90! C90! C90! C90! C9!! C9!! C9!! C9!! C9?! C9?! C9?! C9?! CkT CkT CkT CkT
!? !? !? !? !?b\!0?l !?b\!0?l !?b\!0?l !?b\!0?l Clk^MTC C^l^CTTOk Clk^MTC C^l^CTTOk Clk^MTC C^l^CTTOk Clk^MTC C^l^CTTOk CT8!?b?l\!000ll CT8!?b?l\!000ll CT8!?b?l\!000ll CT8!?b?l\!000ll lCS lCS lCS lCS ! !! ! C93 C93 C93 C93 CkT CkT CkT CkT
!3 !3 !3 !3 !00l+0Ml0 !00l+0Ml0 !00l+0Ml0 !00l+0Ml0 MT\T llC.C^l^CTTOk MT\T llC.C^l^CTTOk MT\T llC.C^l^CTTOk MT\T llC.C^l^CTTOk CD!!0!b\+lM CD!!0!b\+lM CD!!0!b\+lM CD!!0!b\+lM blT lCS lCS lCS lCS ! !! ! C93?^ C93?^ C93?^ C93?^ CkT CkT CkT CkT
!+ !+ !+ !+ ?|!00D!000 ?|!00D!000 ?|!00D!000 ?|!00D!000 lkT| CO\\lCTOk lkT| CO\\lCTOk lkT| CO\\lCTOk lkT| CO\\lCTOk C|!0!DY C|!0!DY C|!0!DY C|!0!DY lCS lCS lCS lCS ! !! ! l\9 l\9 l\9 l\9 CkT CkT CkT CkT
! ! ! ! ?b9+DY+0000 ?b9+DY+0000 ?b9+DY+0000 ?b9+DY+0000 +lT\ CO\\lCTOk +lT\ CO\\lCTOk +lT\ CO\\lCTOk +lT\ CO\\lCTOk C|9?.+DY+0C|b C|9?.+DY+0C|b C|9?.+DY+0C|b C|9?.+DY+0C|b lCS lCS lCS lCS ! !! ! \l90? \l90? \l90? \l90? CkT CkT CkT CkT
!b !b !b !b ?b9DY00000 ?b9DY00000 ?b9DY00000 ?b9DY00000 lT\ CO\\lCTOk lT\ CO\\lCTOk lT\ CO\\lCTOk lT\ CO\\lCTOk C|9?.DY00C|b C|9?.DY00C|b C|9?.DY00C|b C|9?.DY00C|b lCS lCS lCS lCS ! !! ! \l90! \l90! \l90! \l90! CkT CkT CkT CkT
! ! ! ! ?0/S?!08000 ?0/S?!08000 ?0/S?!08000 ?0/S?!08000 CkT SOCllT CkT SOCllT CkT SOCllT CkT SOCllT 0/S!0?!08 0/S!0?!08 0/S!0?!08 0/S!0?!08 lCS lCS lCS lCS ! !! ! \S90? \S90? \S90? \S90? CkT CkT CkT CkT
?!S|S CkT bOM ?0!00?! ?!S|S CkT bOM ?0!00?! ?!S|S CkT bOM ?0!00?! ?!S|S CkT bOM ?0!00?!
\OTl:b vo'tu_ !!0\,d't`ou ` ouut `th !:t `u o lbTD't`ou ` u: :mu'' `u
CYl|??9TOll"?!|S.:h! Thu |uu !+ !:+:03 ?0!0
lDl ) dluto) lo ,)[7] ) .`u`ut.u