Privod en

5, Moldavskaya str.
, Moscow, 121467, Russia
+7 (495) 411-7757, [email protected], www.oilgassystems.com
CONTENTS
ABOUT COMPANY
LLC Electrotyazhmash-Privod 4
1. TURBOGENERATORS, SYNCHRONOUS, TWO POLE, AIR COOLED

1.1. TTK line turbogenerators with capacity 16160 MW 1.2. T (TS)-series turbogenerators with 2.563 MW capacities 1.3. TK-series turbogenerators with 1.563 MW capacities 1.4. GTG-series turbogenerators with 2.58 MW capacities 1.5. Special-version turbogenerators
7
7 9 11 12 13
2. Hydrogenerators 3. Small capacity generators

3.1. SG and SGD synchronous generators 3.2. SG-600-2 NF3 and SGV-600-2 NF3 synchronous generators 3.3. Synchronous diesel generators 3.4. GS synchronous generators
15 17
17 18 19 20
4. generator eXcitation control systems

4.1. Synchronous generator excitation control systems with brushless exciters SHUVG 4.2. Control systems for brushless excitation systems of synchronous generators SHUVGM 4.3. Static excitation systems for STS generators
21
21 22 23
5. Turbogenerator liFe support systems

5.1. Air cleaner and air recirculation unit 5.2. Water recirculation devices in air coolers 5.3. Oil supply device for turbogenerator bearings
24
24 24 24
6. TWO POLE SYNCHRONOUS MOTORS, HIGH-SPEED

6.1. STDM-series motors with 6302,000 kW capacities 6.2. STD - series motors with 2,500...12,500 kW capacities 6.3. STD motors, special version 6.4. STDP-series motors, explosion proof 6.5. SDG2 motor to operate gas pressurizers 6.6. RVSD Frequency-regulated, explosion proof synchronous motor with 14,000 kW capacity 6.7. TDS motors with 20,000 and 31,500 kW capacities
26
26 28 30 32 34 35 36
7. Salient pole synchronous motors

7.1. SDK2- and DSK-series compressor motors 7.2. SDKP2-series compressor explosion proof synchronous motors 7.3. SDN general purpose motors
37
37 39 40
8. EXCITATION SYSTEMS FOR SYNCHRONOUS MOTORS

8.1. Excitation control cabinet for brushless exciters of synchronous motors (SHUVD) 8.2. TRN 1P thyristor voltage regulator 8.3. Static thyristor excitation systems for synchronous motors type STSN 8.4. VTE 10-315 and VTE 630/150 T series analog thyristor exciters for synchronous motors
41
41 42 43 44
5, Moldavskaya str., Moscow, 121467, Russia
9. Asynchronous eXplosion prooF motors with a short circuited rotor

9.1. VAO series motors 9.2. V-2500 and V-5000 motors 9.3. VASO-series explosion proof vertical motors 9.4. VAOV series vertical motors
45
45 48 49 51
10. EXPLOSION PROOF, THREE PHASE ASYNCHRONOUS MOTORS WITH A SHORT CIRCUITED ROTOR
10.1. DAZO4 - series ventilated motors 10.2. DAO-type ventilated motors 10.3. AOD-type ventilated two-speed motors 10.4. AZO - series closed-ventilation motors 10.5. DAB special asynchronous motors 10.6. DA4 asynchronous motors 10.7. VASV vertical water-cooled special motors 10.8. DASO vertical motors 10.9. Special asynchronous motors with variable frequency drive 10.9.1. Explosion proof asynchronous squirrel-cage motor DARB 1200 6 NF2 10.9.2. Asynchronous squirrel-cage DARG 3500 8 UM4
52
52 54 55 56 57 57 58 58 59 59 60
11. HIGH-SPEED VARIABLE-FREQUENCY ELECTRIC DRIVES EPRV 12. MOTORS FOR MAIN PUMPING UNITS OF NUCLEAR PLANTS
12.1. Vertical closed asynchronous motor DAVZ-8000-6 AM U5 12.2. Asynchronous two-speed motor DAVDZ-7100/2800-10000-6/8 AM U5
61 62
62 63
13. ELECTRICALLY DRIVEN GAS COMPRESSOR UNITS

13.1. EGPU electrically driven 4.0 MW gas compressor units 13.2. EGPU electrically driven gas compressor units of 6.3 MW 13.3. EGPU electrically driven 8.2 MW gas compressor units 13.4. EGPU electrically driven gas compressor units of 12.5 MW (non-controlled) 13.5. EGPU electrically driven gas compressor units of 12.5 MW (controlled) 13.6. Set of equipment for reconstructing electrically driven gas compressor units of 12.5 MW
65
65 65 66 66 67 68
14. TRANSFORMING EQUIPMENT

14.1 High voltage frequency converters HV-VFD 14.2 High voltage soft starters SSM-HV
70
70 71
15. Traction electrical equipment

15.1 GST traction alternators 15.2 GPT-840-750N2 direct current generator 15.3 ASTM 2800/600-1000 N2 synchronous traction unit 15.4 ASTG 2800/400-1000 N2 and ASTG2 2800/400-1000 N2 synchronous traction units 15.5 VST exciters 15.6 EDU 133 traction motors 15.7 EDU 136 traction motors 15.8 DAT asynchronous traction motors 15.9 4PNJ-200MA direct current motors 15.10 DTK-800M N1 Direct-current traction motor 15.11 DTK-810M NF1 direct-current traction motor 15.12 DPT direct current motors 15.13 5SG, 6SG, 7SG starter-generators
73
73 74 75 76 77 78 79 80 81 82 83 84 85
15.14 DAVT280-15-4/6/12 asynchronous traction motor 15.15 DATE-170 and DAT-170 asynchronous traction motors 15.16 AMVR-37 asynchronous motor for motor-fan 15.17 Kicking coils 15.17.1 DSF-1L N2 power line filter kicking coil for subway cars 15.17.2 DS-2 smoothing kicking coil 15.18 Set of electric equipment and automation for locomotives 15.18.1 PK-1000L - series electropneumatic contactors 15.18.2 PPK-8000L-series electropneumatic switches 15.19 DPT-196M traction motor 15.20 Privod-TRL1 set of traction electric equipment for trolleybuses with reostatic-contactor control systems 15.21 DPT-110 traction motor for trolleybus
86 87 88 89 89 89 90 90 91 92 92 93
16. GOST CONVENTIONS

16.1 Embodiment (in compliance with GOST 2479) 16.2 Cooling method (in compliance with GOST 20459) 16.3 Protection level (in compliance with GOST 14254) 16.4 Climatic versions (in compliance with GOST 15150) 16.5 Categories of location (in compliance with GOST 15150) 16.6 Rated operation mode (in compliance with GOST 18311) 16.7 Explosion protection types and levels (in compliance with GOST 51330)
94
94 94 94 95 95 95 95
LLC Electrotyazhmash-Privod
Electrotyazhmash-Privod LLC is one of the leading manufacturers of electrical-generating equipment of lower and medium capacity ranges and traction equipment for railroad transportation. It is the leader in supplying of equipment for oil and gas production and transportation applications. Electrotyazhmash-Privod LLC provides over 1,500 electrical machines and associated control equipment Turbogenerators, hydraulic generators, synchronous and asynchronous motors, and traction electrical equipment. Electrotyazhmash-Privod LLC produces over 150 medium and large electrical machines of 2 300 MW power range annually.
PRODUCTS:
Turbogenerators Power Output range 1.5 - 160 MW for electrical energy generation based on the steam and gas turbines applications. The Turbogenerators have enhanced efficiency and advanced technical design. Hydraulic turbines generators Power Output range up to 300 MW for electrical energy generation based on the hydraulic turbines applications. Hydraulic turbines of wide power output range, with both vertical and horizontal design and are manufactured according to GOST 5616 89 and customers specific technical requirements. Synchronous motors Capacity range 0.315 31.5 MW for pump drives, compressor drives, gas blowers, air blowers and other high-speed equipment applications; specialized compressor motors with a range of 0.315 - 1 MW; specialized motors for excavators with a range of 0.6 - 1 MW. Asynchronous motors Capacity range 6.5 KW 12.5 MW, rotation speed - 115 - 8 600 rpm for pump drives, ventilators, smoke exhausters, air blowers, air cooling machines, and other applications; for nuclear plants. Horizontal and vertical motors are produced for various climate conditions, with explosion protection. Electrical gas-pumping units (EGPU) and sets of materiel equipment for EGPU revamp Capacity range 4.0 8.2 MW rotation speed 8000 10000 rpm. for natural gas compression and transportation through main gas pipelines. High-speed, gearless, and frequency-regulated gas-pumping units with the rotors on magnetic bearings. The electric energy consumed by our gas-pumping units is lower by about 30% compare to the equipment provided by other manufacturers. The customers capital costs and installation costs are also reduced. The gas pumps can operate in a wide range of ambient conditions from -60 to +45C. Traction electrical equipment for main-line (cargo and passenger) diesel locomotives; traction motors for subway cars. New products The unique experience of new equipment design enables Electrotyazhmash-Privod LLC to develop high-tech products. The team of designers has an extensive experience in designing new units including development of new projects, rework to the customer's requirements, diagnostics and consultancy in operation and repair of the products manufactured.
Certification of management system and products Integrated management system, built on the principles established by three international standards has been introduced in the company: - Quality management system, complying with ISO 9001:2008; - Environmental management system, complying with ISO 14001:2001; - Safety and health management system, complying with OHSAS 18001:2007. As for production of electrical equipment for the rolling stock of railways, the quality management system of Electrotyazhmash-Privod LLC has a certificate of conformity with the requirements of GOST R ISO 9001:2008. Products of the company, subject to mandatory certification according to the Russian legislation, have conformity certificates. We have a license for fabrication of products for nuclear power plants and a certificate of the equipment conformity with the operating conditions of JSC Gazprom facilities. Electrotyazhmash-Privod LLC cooperates with the independent inspector World Group Bureau Veritas General Conditions. Products are voluntarily certified on the customers request. Products Deliveries The products of Electrotyazhmash-Privod LLC are popular both in Russia and abroad. Our equipment is installed in the power plants in Africa, Asia, and the Middle East. The products are supplied to Latin American countries. Total capacity of the equipment, operated in 35 countries worldwide exceeds 50 000 MW. The largest oil, gas and energy companies, transport machinery companies, metallurgical engineering companies and other large facilities are among the clients of Electrotyazhmash-Privod LLC. Electrotyazhmash-Privod LLC 8, Pozharskogo str., Lysva, Perm Krai, 618 911 +7 (34249) 9-1567, 9-1547 [email protected] www.ngs-privod.ru Products Delivery 5, Moldavskaya str, Moscow, 121467 +7 (495) 411-77-57 [email protected] www.oilgassystems.com
GENERATORS
1. TURBOGENERATORS, SYNCHRONOUS, TWO POLE, AIR COOLED 1.1. TTK line turbogenerators with capacity 16160 MW
TTK tubular body turbogenerators provide electric energy output in connection with steam (P) or gas (G) turbines. Cooling system Cooling method Excitation system Protection level Temperature classification: isolation / application Rated operating conditions closed cycle air cooling with two sectioned air coolers or open cycle cooling system closed cycle ventilation ICW37A81 open cycle ventilation IC31 static or brushless system closed cycle ventilation IP54 open cycle ventilation IP21 or IP54 class F/class S1
Supplied in compliance with GOST 533 and individual customer's requirements. TTK Turbogenerators construction is patented. Delivery set includes: turbogenerator, excitation system, thermal control sensors, mounting equipment, foundation fastenings, spare parts, operation documents. Capacity Generator type -16-2 N3-(P) -16-2 N3-G -20,4-C-2R N3-G * -25-2 N3-(P) -25-2 N3-(P) -25-2 N3-G -25-2 N3-G -32-C-2 N3-(P) -32-C-2 N3-(P) -32-C-2 N3-(P) -32-C-2 N3-G -32-C-2 N3-G -32-C-2 N3-G -37-C-2R * -37-C-2R * -37-C-2R * -40-2 N3-(P) -40-2 N3-(P) -40-2 N3-(P) -40-2 N3-G -40-2 N3-G -40-2 N3-G -50-C-2 N3-(P) -50-C-2 N3-G -63-2 N3-(P) -63-2 N3-G -65-C-2R N3-G * -65-C-2R N3-G * -65-C-2R N3-G * -70-2 N3-(P) -70-2 N3-G kW 16000 16000 20400 25000 25000 25000 25000 32000 32000 32000 32000 32000 32000 37000 37000 37000 40000 40000 40000 40000 40000 40000 50000 50000 63000 63000 65000 65000 65000 70000 70000 kVA 20000 20000 25500 31250 31250 31250 31250 40000 40000 40000 40000 40000 40000 46250 46250 43530 50000 50000 50000 50000 50000 50000 62500 62500 78750 78750 81250 81250 81250 87500 87500 Voltage, V 10500 10500 10500 6300 10500 6300 10500 10500 6300 6300 10500 6300 6300 10500 11000 13800 6300 6300 10500 6300 6300 10500 10500 10500 10500 10500 10500 11000 13800 10500 10500 Phase connection pattern star star star delta star delta star star delta star star delta star star star star delta star star delta star star star star star star star star star star star Rotation speed, rpm 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3600 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3600 3000 3000 Efficiency, % 98.2 98.2 98.2 98.2 98.2 98.2 98.2 98.3 98.3 98.3 98.3 98.3 98.3 98.25 98.25 98.25 98.4 98.4 98.4 98.4 98.4 98.4 98.4 98.4 98.4 98.4 98.4 98.4 98.4 98.4 98.4 Weight, kg 30500 30700 32300 56000 56000 56900 56900 59600 59600 59600 60400 60400 60400 54800 54800 54800 69500 69500 69500 70300 70300 70300 78300 78300 104000 104800 78200 78200 78200 121800 123000 Embodiment IM 1301 IM 1101 IM 1101 IM 1301 IM 1301 IM 1101 IM 1101 IM 1301 IM 1301 IM 1301 IM 1101 IM 1101 IM 1101 IM 1005 IM 1005 IM 1005 IM 1301 IM 1301 IM 1301 IM 1101 IM 1101 IM 1101 IM 1101 IM 1101 IM 7101 IM 7306 IM 1005 IM 1005 IM 1005 IM 7101 IM 7306
Capacity Generator type -80-2 N3-(P) -80-2 N3-G -110-2 N3-(P) -110-2 N3-G -160-2 N3-(P) -160-2 N3-G kW 80000 80000 110000 110000 160000 160000 kVA 100000 100000 137500 137500 188000 188000 Voltage, V 10500 10500 10500 10500 15750 15750
Phase connection pattern star star star star star star
Rotation speed, rpm 3000 3000 3000 3000 3000 3000
Efficiency, % 98.4 98.4 98.45 98.45 98.5 98.5
Weight, kg 121800 123000 158500 160500 207500 210000
Embodiment IM 7101 IM 7306 IM 7101 IM 7306 IM 7101 IM 7306
Note: * rated power at incoming cooling air temperature +15C Embodiment: IM 1005 - feet-based machines with two bearing shields and a single cylindrical shaft end IM 1101 - high feet-based machines with two bearing shields and a single cylindrical shaft end IM 1301 - high feet-based machines with one bearing shield and a single cylindrical shaft end IM 7101 - high feet-based machines with pedestal bearings, without fundament or base plates and with a single cylindrical shaft end IM 7306 - high feet-based machines with pedestal bearings, without fundament or base plates and with two flanged shaft ends XX 2 O N (NF) 3 (4) G (P)
G -connected to gas turbine (P) - connected to steam turbine category of location climatic version open-loop ventilation number of poles compact line rated capacity, MW tubular body turbogenerator
1.2. T (TS)-series turbogenerators with 2.563 MW capacities

T-series Turbogenerators coupled with steam (P) or gas (G) turbine are designed for power generation. Cooling system Cooling method closed-loop air cooling with water air coolers or open-lop air cooling IC31 - 10 2R NF3 ICW37A71 or IC31 Turbogenerators with the capacity of 12, 16, 20 and 25 MW ICW37A71 other units static or brushless T-2, 5-2, T-4-2, T-6-2, T-8-2, T-12-2, TS-32-2, T-50-2, TS-63-2 - lower TS-10-2R or TS-12-2R - side T-16-2 lower or side TS-20-2 and T-25-2 upper, lower, or side T-32-2 upper or lower IP44 Turbogenerators T-2, 5-2, T-4-2, T-6-2 and T-12-2 IP55 - Turbogenerators T-25-2Z N3-G, T-25-2Z N3-P IP54 - Turbogenerators -25-2R N3-G, T-25-2 with the capacity of 16, 20, 32, 50 MW, TS-63-2 S1
Excitation system Location of HV leads of turbogenerators
Protection level
Rated operating conditions
Manufactured in compliance with GOST 533 and customers specific technical requirements. Design of turbogenerator T-25-2 is protected with utility patent No. 37439; design of turbogenerator TS-63-2 is protected with utility patent No. 36585 Certificates of conformity: No. ROSS RU.MH07.N00338 for T-25-2 N3; No. ROSS RU.MH08.N00077 for -16-2R NF3.1; No. ROSS RU.MH08.N00059 for -12-2R NF3. Delivery set includes: turbogenerator, excitation system, thermal control sensors, mounting equipment, foundation fastenings, spare parts, operation documents. Capacity Generator type -2,5-2 N3 (P) -2,5-2 N3 (P) -2,5-2 N3 (P) -4-2 N3 (P) -4-2 N3 (P) -4-2 N3 (P) -6-2 N3 (P) -6-2 N3 (P) -6-2 N3 (P) -8-2 N3 (P) -12-2 N3 (P) -12-2 N3 (P) S-12-2R NF3 (G) S-12-2R NF3 (G) -16-2R NF3.1 (G) -16-2R NF3.1 (G) -16-2 N3-G -16-2 N3-G -16-2 N3-(P) -16-2 N3-(P) kW 2500 2500 2500 4000 4000 4000 6000 6000 6000 8000 12000 12000 12000 12000 16000 16000 16000 16000 16000 16000 kVA 3125 3125 3125 5000 5000 5000 7500 7500 7500 10000 15000 15000 15000 15000 20000 20000 20000 20000 20000 20000 Voltage, V 3150 6300 10500 3150 6300 10500 3150 6300 10500 6300 6300 10500 6300 10500 6300 10500 6300 10500 6300 10500 Phase connection pattern star star star star star star star star star star star star star star star star star star star star
Rotation speed, rpm 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
Efficiency, % 97.0 97.0 96.8 97.3 97.3 97.0 97.6 97.6 97.6 97.6 97.65 97.65 97.65 97.65 97.8 97.8 98.0 98.0 97.8 97.8
Weight, kg 12500 12500 12500 15000 15000 15000 22500 20000 20000 27000 28025 28825 39815 39815 61580 61580 61800 61800 52000 52000
Embodiment IM 7011 IM 7011 IM 7011 IM 7011 IM 7011 IM 7011 IM 7011 IM 7011 IM 7011 IM 7011 IM 7011 IM 7011 IM 7211 IM 7211 IM 7211 IM 7211 IM 7211 IM 7211 IM 7121 IM 7121
Capacity Generator type S-20-2 N3-G S-20-2 N3-G S-20-2 N3-(P) S-20-2 N3-(P) -25-2Z N3-G -25-2Z N3-G -25-2Z N3-(P) -25-2Z N3-(P) -25-2Z N3-(P) -25-2R N3-G -25-2R N3-G -25-2R N3-G S-32-2 NF3-(P) S-32-2 NF3-(P) -32-2 V3-(P) -32-2 V3-(P) -32-2 V3-G -32-2 V3-G -50-2 N3-(P) -50-2 N3-(P) S-63-2 V3-(P) S-63-2 V3-(P) kW 20000 20000 20000 20000 25000 25000 25000 25000 25000 25000 25000 25000 32000 32000 32000 32000 32000 32000 50000 50000 63000 63000 kVA 25000 25000 25000 25000 31250 31250 31250 31250 31250 31250 31250 31250 40000 40000 40000 40000 40000 40000 62500 62500 78750 78750 Voltage, V 6300 10500 6300 10500 6300 10500 6300 6300 10500 6300 6300 10500 6300 10500 6300 10500 6300 10500 6300 10500 6300 10500
Phase connection pattern delta star delta star delta star delta star star delta star star delta star delta star delta star delta star delta star
Rotation speed, rpm 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
Efficiency, % 98.0 98.0 98.0 98.0 98.0 98.0 98.0 98.0 98.0 98.0 98.0 98.0 98.2 98.2 98.4 98.4 98.4 98.4 98.2 98.2 98.4 98.4
Weight, kg 66600 66600 56500 56500 86750 86750 69500 69500 69500 85600 85500 85600 78800 78800 79500 79500 83000 83000 143000 143000 143000 143000
Embodiment IM 7211 IM 7211 IM 7121 IM 7121 IM 7211 IM 7211 IM 7121 IM 7121 IM 7121 IM 7211 IM 7211 IM 7211 IM 7121 IM 7121 IM 7121 IM 7121 IM 7321 IM 7321 IM 7121 IM 7121 IM 7121 IM 7121
(S)
XX
R (Z)
N (V, T, NF)
3 (3.1)
G (P)
G - connected to gas turbine P - connected to steam turbine
category of location climatic version R-open-loop ventilation Z-closed-loop ventilation number of poles capacity, MW turbogenerator S turbogenerator, special version
10
1.3. TK-series turbogenerators with 1.563 MW capacities

Turbogenerators with open-loop ventilation coupled with gas (G) turbines are designed for power generation as a part of steam turbine power plants. Turbogenerators TK with closed-loop ventilation coupled with steam (P) turbines are designed for power generation as apart of steam turbine power plants. Embodiment Cooling system Cooling method Excitation system Protection level Rated operating conditions IM 1001 turbogenerators with open-loop ventilation air cooling (can be equipped with air treatment and recirculation unit) turbogenerators with closed-loop ventilation through water air cooler, located at the top of the casing IC31 - Turbogenerators with open-loop ventilation ICW37A81 - Turbogenerators with closed-loop ventilation brushless IP54 S1
Manufactured in compliance with GOST 533 and customers specific technical requirements. Design of Turbogenerators with open-loop ventilation is protected with utility patent No. 29188. Certificates of conformity: No. ROSS RU. MH08. N 00064 for TK-6-2R N3; No. ROSS RU. MH08. N 00060 for TK-2.5-2R NF3. Delivery set includes: turbogenerator, excitation system, thermal control sensors, mounting equipment, foundation fastenings, spare parts, operation documents. Generator type -1,5-2R NF3 -1,5-2R NF3 -1,5-2Z NF3 -1,5-2Z NF3 -2,5-2R NF3 -2,5-2R NF3 -2,5-2Z N3 -2,5-2Z N3 -4-2R NF3 -4-2R NF3 -4-2Z N3 -4-2Z N3 -6-2R NF3 -6-2R NF3 -6-2Z N3 -6-2Z N3 Capacity kW 1500 1500 1500 1500 2500 2500 2500 2500 4000 4000 4000 4000 6000 6000 6000 6000 kVA 1875 1875 1875 1875 3125 3125 3125 3125 5000 5000 5000 5000 7500 7500 7500 7500 Voltage, V 6300 10500 6300 10500 6300 10500 6300 10500 6300 10500 6300 10500 6300 10500 6300 10500 Rotation speed, rpm 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 Efficiency, % 95.8 96.0 96.0 96.0 96.8 96.7 96.8 96.7 97.0 97.0 97.2 97.0 97.4 97.4 97.4 97.4 Weight, kg 7600 7600 7600 7600 12700 12700 10500 10500 13000 13000 13500 13500 20040 20040 18000 18000
R (Z)
NF (N)
climatic version
3
category of location
R-open-loop ventilation, Z-closed-loop ventilation number of poles capacity, MW mounted in a housing turbogenerator
11
1.4. GTG-series turbogenerators with 2.58 MW capacities

GTG Turbogenerators coupled with gas (G) turbines are designed to operate as part of gas turbine power stations. Embodiment Cooling system Cooling method Excitation system Protection level Rated operating conditions IM 7211 open-loop IC31 brushless IP54 S1
Manufactured in compliance with GOST 533 and customers specific technical requirements. Design of Turbogenerators is protected with utility patent No. 29188. Certificates of conformity: No. ROSS PU. MH02. N 00058 for GTG-2, 5-2R NF3 and GTG-4-2R NF3; No. ROSS PU. MH08. N 00068 for GTG-6-2R NF3. Delivery set includes: turbogenerator, excitation system, thermal control sensors, mounting equipment, foundation fastenings, spare parts, operation documents. Can be equipped with air treatment and recirculation unit. Capacity kW 2500 2500 4000 4000 6000 6000 8000 8000 kVA 3125 3125 5000 5000 7500 7500 10000 10000
Generator type GTG-2,5-2R NF3 GTG-2,5-2R NF3 GTG-4-2R NF3 GTG-4-2R NF3 GTG-6-2R NF3 GTG-6-2R NF3 GTG-8-2R NF3* GTG-8-2R NF3*
Voltage, V 6300 10500 6300 10500 6300 10500 6300 10500
Rotation speed, rpm 3000 3000 3000 3000 3000 3000 3000 3000
Efficiency, % 96.8 96.7 97.2 97.0 97.5 97.5 97.6 97.5
Weight, kg 13900 13900 15550 15550 20500 20500 27360 27360
* GTG-8-2R NF3 generator may be delivered with closed-loop ventilation GTG XX 2 R NF

climatic version open-loop ventilation number of poles capacity, MW gas turbogenerator
3
12
1.5. Special-version turbogenerators

T-2.5-3600 T3 and T-4-3600 T3 are three phase turbogenerators with frequency of 60 Hz and Rotation speed of 3,600 rpm, equipped with electric excitation unit; they are designed to operate with steam turbine in non-explosive environment in the tropics. TK-2.5 2Z T3 three phase turbogenerator, frequency - 50 Hz, voltage - 6,600 V, Rotation speed - 3,000 rpm, brushless excitation system, is designed for electric power generation in operation with a steam turbine in explosion-proof atmosphere in the tropics. TM-4-3600 T3 three phase turbogenerator with frequency of 60 Hz, Rotation speed of 3,600 rpm and brushless exciter is designed to operate with steam turbine in non-explosive environment in the tropics. T-6-2R T3.1 two plug-in friction bearing turbogenerator with brushless exciter, open loop type ventilation and side outputs location is installed in transportable automatic power stations with marine gas turbine motor drive in the tropics. T-6-2Z N3.1 two plug-in friction bearing turbogenerator with brushless exciter, close loop type ventilation and side outputs location is designed to operate with gasturbine motor drive under temperate conditions. T-6-2Z T3.1 two plug-in type friction bearing turbogenerator with brushless exciter, close loop type ventilation and side outputs location is designed to operate with gas-turbine motor drive in the tropics. T-6-2R N3 turbogenerator with top location of the stator lead is designed to operate with gas turbine motor. T-12-2E N3 turbogenerator with top location of the stator lead is designed to be installed in packaged or floating gas-turbine power stations. TP-12-2 N3 (T3) EP turbogenerator with the following explosion protection type Case filling or blowing under P excess pressure valve IExpxIIT5X in compliance with GOST R 51330.0. is designed for continuous running with a top pressure recovery turbine (TPRT) . T-12-2.2 N3 two pillar type friction bearing turbogenerator with bottom location of the stator lead is designed to operate with steam turbines drive. TT-12-2A N3 turbogenerator with bottom location of the stator lead and open loop type ventilation is designed to operate with GTER-12 gas turbine drive. T-4.5-2I T3, T-5-2I T3, T-6-2I 3, T-7.5 -2I 3, T-7, 7-2I T3, and T-12-2 T3 turbogenerators with one pillar type bearing are designed for electric power generation in operation with a steam turbine (50 Hz AC) in the tropics. T-25-3600 T3 turbogenerator with bottom location of the stator lead and closed-loop type ventilation, on two pillar type friction bearings, without base plate is designed for electric power generation in operation with a steam turbine (60 Hz AC) in the tropics. Delivery set includes: turbogenerator, excitation system, thermal control sensors, mounting equipment, foundation accessories, spare parts, operation documents. Generator type -2.5-3600 3 -2.5-2Z 3 -4-3600 3 -4-3600 3 -4.5-2I 3 -5-2I 3 -6-2R 3.1 -6-2R 3.1 -6-2Z N3.1 -6-2Z N3.1 -6-2Z 3.1 -6-2Z 3.1 -6-2I 3 -6-2I 3 Capacity kW 2500 2500 4000 4000 4500 5000 6000 6000 6000 6000 6000 6000 6000 6000 kVA 3125 3125 5000 5000 5625 6250 7500 7500 7500 7500 7500 7500 7500 7500 Voltage, V 6300 6600 6300 6300 11000 11000 6300 10500 6300 10500 6300 10500 6600 11000 Rotation speed, rpm 3600 3000 3600 3600 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 Efficiency, % 96.5 96.8 96.6 96.6 97.2 97.4 97.3 97.3 97.3 97.3 97.3 97.3 97.6 97.6 Weight, kg 12500 10500 15000 15000 20000 21120 16000 16000 16800 16800 16800 16800 23500 24000
13
Generator type -6-2E N3 -7.5-2I 3 -7.7-2I 3 -12-2 3 -12-2 3 -12-2E N3 -12-2E N3 P 12-2 N3 (3) P 12-2 N3 (3) P 12-2 N3 (3) -12-2.2 N3 -12-2.2 N3 -12-2 N3 -25-3600 3
Capacity kW 6000 7500 7700 12000 12000 12000 12000 12000 12000 12000 12000 12000 12000 25000 kVA 7500 9375 9625 15000 15000 15000 15000 15000 15000 15000 15000 15000 15000 31250
Voltage, V 6300 11000 11000 6600 11000 6300 10500 6300 10500 11000 6300 10500 10500 10500
Rotation speed, rpm 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3600
Efficiency, % 97.48 97.7 97.6 98.0 98.0 97.65 97.65 97.65 97.65 97.65 97.65 97.65 97.65 97.7
Weight, kg 22850 26100 26100 29000 30450 29800 30400 28600 29400 29800 29880 30680 31800 59900
(P, )
R (Z)
I (E, )
N()
climatic version
3 (3.1)
E - for packaged and floating power stations, A - for delivery to Argentina, I - for delivery to India R - open ventilation loop Z - close ventilation loop number of poles capacity, MW T-turbogenerator TP-ventilated turbogenerator TK- casing-type turbogenerator
()
XX
3600
climatic version
3
rotation speed, rpm capacity, MW T-turbogenerator TM marine turbogenerator
14
2. Hydrogenerators
Production facilities of Electrotyazhmash-Privod LLC enable the manufacture of air cooling hydro-generators with a wide range of capacities, from 1 to 300 MW, vertical or horizontal types of constructions, thus ensuring that almost any Customer requirement is met. A team of company designers and engineering center specialists has acquired unique experience in designing new hydrogenerators and retrofitting power generation facilities, both in Russia and across the world. The hydrogenerators are delivered complete with accessory systems (excitation, cooling, stopping, fire-extinguisher, thermal control and other components), sets of spare parts, tools and installation accessories for the period of guaranteed and designed commercial operations. Manufactured in compliance with GOST 5616 89 and customer's specific technical requirements. List of hydrogenerators in production, with facilities at which they operate: Type of hydrogenerator VGS 260/20-24 VGS 260/20-24 VGS 260/34-24 VGS 260/34-24 SGG 1600-600 GS 213/15-24 VGSP 213/24-28 VGSP 215/24-16 VGSP 213/15-20 VGSP 215/20-20 VGSP 213/29-14 SGG 2500-750 VGSP 325/69-28 VGSP 213/24-28 VGS 260/24-24 VGS 260/34-24 VGS 375/79-24 VGSP 213/29-14 VGS 260/34-24 VGS 4500-375 VGS 525/150-20 VGS 213/24-14 VGSP 215/20-20 VGSP 215/20-20 VGS 275/140-10 SGG 2000-600 VGS 325/89-14 VSG 260/31-18 VSG 260/31-18 VSG 260/31-18 SV-260/65-12 SV-465/215-16 VGS-1525/135-120 SV-328/79-32 NF4 SV-448/140-18 4 SV-783/105-40 SV-640/140-30 Capacity, kW 680 680 1250 1250 1600 200 400 800 320 500 1000 2500 4000 400 840 1250 8800 1000 1250 4500 46000 800 500 500 14350 2000 10000 1600 1600 1600 6000 56100 66000 3550 43470 52250 50000 Rotation speed, rpm 250 250 250 250 600 250 214.3 375 300 300 428.6 7500 214.3 214.3 250 250 250 428,6 250 375 300 428.6 300 300 600 600 428.6 333.3 333.3 333.3 500 375 50 187,5 400 150 200 Voltage, V 6300 6300 6300 6300 6300 400/230 6300 6300 400/230 6300 6300 6300 6300 400/230 6300 6300 6300 6300 6300 6300 10500 6300 6300 6300 6300 6300 6300 6300 6300 6300 6300 10500 10500 10500 13800 13800 10500 vertical vertical vertical vertical vertical horizontal vertical vertical vertical vertical vertical vertical vertical vertical vertical vertical vertical vertical vertical horizontal vertical vertical vertical vertical vertical vertical vertical vertical vertical vertical vertical Embodiment vertical vertical vertical vertical horizontal Qnty 1 2 1 1 2 1 2 2 1 2 2 3 1 1 1 1 1 2 4 1 1 3 1 2 2 5 3 2 1 2 1 1 3 4 2 1 2 Operating company Kuzu Gusarksaya HPS Skorodninskaya HPS Mozhayskaya HPS Sheshnevskaya HPS Gergebilskaya HPS HPS Krasnoy Armii Kudrinskaya HPS Antonovskaya HPS HPS Aksu HPS Murgab Uslenovskaya HPS Zeykhurskaya HPS HPS Ladyzhinskaya Okulovskaya HPS HPS of the Shershinskoye water reservoir Belokholunitskaya HPS Tsentralnaya HPS Sergeyevskaya HPS Ruzskaya HPS Sosenskaya HPS Kubanskaya HPS-2 HPS Vanch HPS Shudisand HPS Shudsksand HPS Chamezgi HPS Khorog Atbashinskaya HPS HPS Mansur Vazuzskaya hydrosystem HPS 34 of Mozhaysky waterworks Sengileyevskaya HPS HPS Argel Saratovskaya HPS Yegorlykskaya HPS 2 HPS Baytun HPS Rukatayo Gotsatlinskaya HPS Year of supply 1955 1957 1958 1959 1959 1960 1960 1960 1961 1961 1961 1961-1963 1962 1963 1963 1963 1963 1964 1964 1964 1964 1966 1967 1967 1967 1967-1972 1969-1970 1972 1972 1997 2005 2005 2005-2007 2009 2011 2011 2012 Country Uzbekistan Russia Russia Russia Russia Turkmenistan Kazakhstan Kazakhstan Kazakhstan Tajikistan Russia Azerbaijan Russia Russia Russia Russia Russia Kazakhstan Russia Russia Russia Georgia Kirghizia Tajikistan Abkhazia Tajikistan Kirghizia Morocco Russia Russia Russia Armenia Russia Russia Panama Chile Russia
15
VGS (VGS, SV, VSG, GS)
XXX
YY
NF ()
climatic version number of poles
4
stator core, size, cm stator core diameter, cm VGS - synchronous vertical hydro-generator VGSM modernized synchronous vertical hydrogenerator SV - synchronous vertical VSG - synchronous vertical hydro-generator GS synchronous hydrogenerator
SGG
XXXX
YYY
NF
climatic version
4
rotation speed, rpm capacity, kW synchronous horizontal hydrogenerator
16
3. Small capacity generators 3.1. SG and SGD synchronous generators

SG 16-31.5-6 NF3 synchronous generator is designed for power generation with gas turbine, and SGD 16-31.5-2 NF2 synchronous generator with diesel motors. They are installed in transportable power stations. Embodiment Cooling system Cooling method Excitation system Protection level Rated operating conditions IM 1001 air cooling, open-loop IC01 brushless IP22 S1
Manufactured in compliance with GOST 52776 2007 and customers specific technical requirements. Delivery set includes: generator, exciter, control station, spare parts, operation documents. Capacity kW 1000 1000 kVA 1250 1250
Type of product SG16-31.5-6 NF2 SGD16-31.5-6 NF2
Voltage, V 6300 6300
Rotation speed, rpm 1000 1000
Efficiency, % 95.0 95.2
Weight, kg 5450 5600
SG (SGD)
16
31.5
NF
climatic version
2
number of poles stator core size, cm size designation synchronous diesel generator
17
3.2. SG-600-2 NF3 and SGV-600-2 NF3 synchronous generators

The SG-60O2 NF3 and SGV-60O2 NF3 synchronous generators are designed to generate power as part of pneumatic electric generator units on the basis of energy derived from gas pressure differences in gas production, transportation and distribution systems Embodiment Height of rotation axis Cooling system Excitation system Protection level Rated operating conditions IM 1103 300 mm open-loop. Generator is cooled with the natural gas passing through the shell (about 98% methane) in compliance with GOST 51.40 93. Cooling of the excitation control unit air self-cooling brushless. Generator SGV2 600 2 NF3 allows connection to mains by self-synchronization IP10 S1
Manufactured in compliance with GOST 52776 2007 and customers specific technical requirements. Delivery set includes: generator, excitation system with control unit, spare parts, operation documents. Capacity kW 600 600 600 kVA 750 750 750 Efficiency, % 89.0 90.0 90.0
Type of generator SG-600-2 NF3 SGV-600-2 NF3 SGV2-600-2 NF3
Voltage, V 400 10500 10500
Rotation speed, rpm 3000 3000 3000
Power factor 0.8 0.8 0.8
Weight, kg 2040 2050 2050
SG (SGV)
600
NF
climatic version
3
number of poles capacity, kW series synchronous generator (high-voltage synchronous generator )
18
3.3. Synchronous diesel generators

Synchronous diesel generators are designed to generate power as a part of diesel power plants. Designed for use as a main or standby three phase AC power supply driven by combustion motors. Embodiment Cooling system Cooling method Excitation system Protection level Explosion protection type and level Rated operating conditions IIM 1305 GSD generators IM 1101 SGDP generators air cooling, open-loop IC01 - GSD-800-750 NF2 (NF4), GSD-1000-1000 NF4 IC31 - GSD-1650-1000 NF2 (N2, T2), GSD-1600-1000 NF4, GSD-1100-1000 NF2 ICW37A71 - SGDP-3150-12 N3 brushless IP23 - GSD-800-750 NF4 IP44 other generators ExpIIT3 - SGDP-3150-12 U3 S1
Manufactured in compliance with GOST 52776 2007 and customers specific technical requirements. Delivery set includes: exciter, excitation controller, excessive pressure monitor (for SGDP-3150-12N3), component parts, operation documents. Capacity kW 800 800 800 800 1000 1000 1000 1100 1100 1600 1650 1650 3150 kVA 1000 1000 1000 1000 1250 1250 1250 1375 1375 2000 2062 2062 3938
Type of generator GSDF-800-750 NF3 (3) GSD-800-750 NF2 GSD-800-750 NF2 GSD-800-750 NF4 GSD-1000-1000 NF4 GSD-1000-1000 NF4 GSD-1000-1000 NF4 GSD-1100-1000 NF2 GSD-1100-1000 NF2 GSD-1600-1000 NF4 GSD-1650-1000 NF2 (N2, 2) GSD-1650-1000 NF2 (N2, 2) SGDP-3150-12 N3
Voltage, V 6300 6300 10500 400 400 6300 11000 6300 10500 10500 6300 10500 6300
Rotation speed, rpm 750 750 750 750 1000 1000 1000 1000 1000 1000 1000 1000 500
Efficiency, % 95.0 95.2 95.5 95.2 96.1 95.9 95.9 96.2 96.0 95.5 95.8 95.5 96.0
Weight, kg 6600 6010 6110 5750 5650 5450 5450 6180 6145 9000 9000 9000 24000
GSD
XXX
XXX
NF (N, )
climatic version
2 (3, 4)
rotation speed capacity, kW flanged synchronous diesel generator
SGDP
3150
12
N
climatic version
3
number of poles capacity, kW synchronous, ventilated diesel generator
19
3.4. GS synchronous generators

The synchronous diesel generators are designed to generate three phase AC electric power as a part of a bio-energy plant. Embodiment Cooling system Cooling method Excitation system Protection level Rated operating conditions IM 1001 air cooling, open-loop IC01 brushless IP22 S1
Manufactured in compliance with GOST 52776 2007 and customers specific technical requirements. Delivery set includes: generator, exciter, control station, half-coupling, key, spare parts, operation documents. Capacity kW 600 630 kVA 750 787.5
Type of generator GS-600-1500 NF2 GS-630-1500 NF2
Voltage, V 6300 400
Rotation speed, rpm 1500 1500
Weight, kg 3700 3700
GS
XXX
1500
NF
climatic version
2
rotation speed capacity, kW synchronous generator
20
4. generator eXcitation control systems 4.1. Synchronous generator excitation control systems with brushless exciters SHUVG
A SHUVG control system ensures the supply of automatically controlled direct current power to the excitation coil of synchronous generators brushless exciters. Control system for exciter SHUVG (generator excitation control systems) is designed for: automatic current control of brushless exciters of synchronous generators; implementation of control functions and data; connections to the top-level of control; interaction with an operator; excitation system and generator equipment protection (off-design operation protection of the brushless exciter, overload protection of the generator rotor, protection of the generator from voltage rise and underfrequency of the stator). SHUVG-200 NF4 is designed for control of exciter of synchronous generators GTG, TK, and K with the capacity up to 12 MW. SHUVG-220 NF4, SHUVG -240 NF4 is designed for control of brushless exciter of synchronous generators GTG, KT, T and TS with the capacity up to 25 MW. Manufactured in compliance with GOST 21558 2009 and customers specific technical requirements. Delivery set includes: control cabinet; set of supplying transformers of OLS- 1.25/6(10) N2 (for SHUVG 220 NF4 and SHUVG 240 NF4 - 3 pcs, for SHUV 200 NF4, SHUVG 210 NF4 - 1 pc) on request; set of spare parts and accessories; operation documents. Basic technical parameters Rated voltage of excitation coil, V Rated current, A Boosting ratio for current, relative units Duration of boosting, sec. Rated voltage of supply system alternating, V operational, direct, V Maintenance 220 27 One-sided 3380 110 or 220 One-sided Two-sided SHUVG-200 NF4 60 6 2 Max. 50 SHUVG-220 NF4 SHUVG-240 NF4 90 8 2 Max. 50
SHUVG
0 (2; 4)
NF
climatic version
4
for the brushless exciters 0 - in a one-side access cabinet of the smaller size, with one matching transformer; 2 - in one-side access cabinet, with one matching transformer; 4 - in a two-sides access cabinet, with two matching transformers two-channel system with an automatic field regulator and an excitation current regulator generator excitation control cabinet
21
4.2. Control systems for brushless excitation systems of synchronous generators SHUVGM
Digital control systems of brushless exciters for synchronous generators SHUVGM are designed for: automatically controlled direct current power to the excitation coil of brushless exciters of synchronous generators; initial excitation of generator to the set value; adjustment of the generators voltage to the mains voltage; operation in the grid and for dedicated load in all permissible operating conditions - from idle run to rated load; operation in automatic and manual control modes with smooth transition between modes; smooth transition between channels for two-channel circuit; excitation boosting in case of voltage drop on generator busbars; limitation of minimum excitation according to the generators capacity curve; limitation of the boosted value of the excitation current at the set value and for duration; limitation of the excitation coil overload; generator field breaking in emergency conditions and in case of normal shutdown; connections to the top-level of automatic control system. Excitation control systems SHUGVM provide the automatic regulation of excitation current in brushless synchronous generators excitation systems. Manufactured in compliance with GOST 21558 2000 and customers specific technical requirements. Delivery set includes: control cabinet; set of supplying transformers of OLS- 1.25/6(10) N2 - 3 pcs or 3AC380V/240V, 4 kVA - 1(2) pcs on request; set of spare parts and accessories; operation documents. Basic technical parameters Rated rectified voltage, V Rated rectified current, A Forcing current, (related to I rated), minimum level Forcing duration, s., minimum Rated power voltage, V AC voltage Operative DC Maintenance Protection level Climatic version Category of location Features W/o PLC and operator's panel 380 220 (110) One-sided 380 220 (110) One-sided IP21 or other on request NF, N, 4 With PLC and operator's panel With PLC and operator's panel 380 220 (110) One-sided SHUVGM-200-1(2) -6-50 100 15 2.0 20 SHUVGM-200-1(2) -15-100 100 15 2.0 20 SHUVGM-400-1(2) (P) -50-200 100 20 2.5 20 to 30
* Power supply circuit for the excitation system is determined by the customer
SHUVGM
200 ()
1 (2)
NF (, )
climatic version rated rectified voltage, V
4
rated current of the cabinet (rectified), A E self-cooling number of control channels for control and power parts controller series microprocessor-based generator excitation control cabinet
22
4.3. Static excitation systems for STS generators

Static excitation systems for generators with power supply from generator busbars (STS...S) and with power supply from auxiliary busbars except from generator (STS...N) are designed for: automatically controlled direct current power to the excitation coil of generators in normal and emergency modes; initial excitation of generator to the set value; adjustment of the generators voltage to the mains voltage; operation in the grid and for dedicated load in all permissible operating conditions - from idle run to rated load; operation in automatic and manual control modes with smooth transition between modes; smooth transition between channels for two-channel circuit; excitation boosting in case of voltage drop on generator busbars; limitation of minimum excitation according to the generators capacity curve; limitation of the boosted value of the excitation current at the set value and for duration; limitation of the excitation coil overload; generator field breaking in emergency conditions and in case of normal shutdown; connections to the top-level of automatic control system. Manufactured in compliance with GOST 21558 2000 and customers specific technical requirements. Basic technical data Rated excitation current, A Rated excitation voltage, V Supply voltage of the rectifying transformer, kV Protection level * Climatic version Category of location *Different protection level to be agreed upon with the customer Protections of generator and transformer (as per ANSI code), integrated in the excitation systems or as a separate cabinet*: overexcitation protection (24); positive sequence undervoltage protection (27); reverse power protection (32); excitation loss protection (40); negative phase-sequence-current protection (46); phase-to-phase short-circuit current protection (50); generator circuit-breaker failure protection (50BF); voltage depending current protection (51V); stator coil ground fault protection* (51N, 59N); generator overvoltage protection (59); rotor ground fault protection (64); generators longitudinal differential protection* (87); additional protections of the rectifying transformer*; other protections as agreed upon with the customer. *Supplied extra on the customers request STS 1 (2) P S(N) XX 2.5 NF (, )
climatic version voltage boosting ratio rated current of the excitation system rated voltage of the excitation system S- power supply by self-excitation N-power supply from an independent source forced cooling number of control channels for control and power parts static thyristor system
300 to 3000 120 to 450 6.3; 10.5; 13.8; 15.75; 20 IP21, IP22, IP23 NF, N, 4
4
Standby excitation lead-in cabinet (SHVRV) can be supplied on the basis of an additional agreement.
23
5. Turbogenerator liFe support systems 5.1. Air cleaner and air recirculation unit
The air cleaner and air recirculation unit is designed to run in conjunction with TK-series open loop ventilation turbogenerators, and serves to clean and pre-heat air flowing into the generator. The air flowing into the generator is heated by means of utilizing heat removed from operational losses. The cooling air recirculation system ensures generator start-up and operations within a temperature range of 60C below zero to 5C above zero. Climatic version NF. Category of location 3. The air-mixing chamber should be located inside the generator container, and the air cleaning chamber should be stationed on the container roof. Parameters and performance data Rated capacity of air flow, m /hour
3
Norms 4.68 98 415 1290
Efficiency of dust particles removal, size 10 mkm and more, % Hydraulic friction, Pa Module weight, kg
5.2. Water recirculation devices in air coolers

The devices are designed to arrange closed loop water recirculation in air coolers of T32 generators preventing condensation during cold seasons. For turbogenerators 20 and 32 MW 170 2,5832,7201,850 2,600 For turbogenerators 25 and 63 MW 250 2,6402,7841,832 2,800
Performance data of devices Maximum water flow, m3/hour Size, mm Weight, kg
5.3. Oil supply device for turbogenerator bearings

The oil supply device is designed to provide lubrication to bearings of TS-20, T-16, and T-25 turbogenerators with the capacity of 20-32 MW during their joint operation with a gas turbine. Performance data of device Oil flow rate for 2 bearings, l/min Oil pressure at input of bearings, MPa Size, mm Weight, kg 110 min 0,03, max 0,1 3,4503,120980 4,290 Norms
24
E-MOTORS
25
6. TWO POLE SYNCHRONOUS MOTORS, HIGH-SPEED 6.1. STDM-series motors with 6302,000 kW capacities
STDM-series synchronous turbomotors with the capacity of 630...2,000 kW with 50 Hz AC three phase power supply are designed to operate pumps, compressors, gas pressurizers, air blowers and other fast-running devices operated in the enclosed rooms with explosion-proof atmospheres in conditions of temperate climates. Embodiment Cooling system IM 7211, IM 7311 motors with closed-loop ventilation air cooling, with integrated air coolers operated on fresh water (or on sea water, as greed upon with the manufacturer) motors with open-loop ventilation - air cooling, heated air is discharged through louvers in the stator casing closed-loop ventilation - ICW37A71 open-loop ventilation - IC31 from digital thyristor excitation systems STSN or VTE10-315-series analog thyristor exciters (on request) direct or reactance start, depending on the value of flywheel moments of driven equipment. Frequency starts from thyristor frequency converters (thyristor starter) are possible -as agreed upon with the manufacturer. closed-loop ventilation - I44 open-loop ventilation - I22 S1
Cooling method Excitation system Start Protection level Rated operating conditions
Manufactured in compliance with GOST R 52776 2007 and customers specific technical requirements. Delivery set includes: motor, thermal control sensors, pressure switch sensor, foundation fastenings, mounting equipment, spare parts, operation documents. On customers request, the motor can be equipped with soft starter SSM-HV and frequency converter HV-VFD.
Type of motor STDM-630-2R NF4 STDM-630-2R NF4 STDM-630-2Z NF4 STDM-630-2Z NF4 STDM-800-2R NF4 STDM-800-2R NF4 STDM-800-2Z NF4 STDM-800-2Z NF4 STDM-1000-2R NF4 STDM-1000-2R NF4 STDM-1000-2Z NF4 STDM-1000-2Z NF4 STDM-1250-2R NF4 STDM-1250-2R NF4 STDM-1250-2Z NF4 STDM-1250-2Z NF4 STDM-1600-2R NF4 STDM-1600-2R NF4 STDM-1600-2Z NF4 STDM-1600-2Z NF4 STDM-2000-2R NF4 STDM-2000-2R NF4 STDM-2000-2Z NF4 STDM-2000-2Z NF4
Capacity, kW 630 630 630 630 800 800 800 800 1000 1000 1000 1000 1250 1250 1250 1250 1600 1600 1600 1600 2000 2000 2000 2000
Voltage, V 6000 10000 6000 10000 6000 10000 6000 10000 6000 10000 6000 10000 6000 10000 6000 10000 6000 10000 6000 10000 6000 10000 6000 10000
Rotation speed, rpm 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
Efficiency, % 95.9 95.7 95.9 95.7 96.1 95.9 96.1 95.9 96.5 96.1 96.5 96.1 96.9 96.5 96.9 96.5 97.0 96.7 97.0 96.7 97.0 96.9 97.0 96.9
Weight, kg 3800 3800 4400 4400 4000 4000 4600 4600 4500 4500 5000 5000 6000 6000 6400 6400 6200 6200 7000 7000 6600 6600 7500 7500
26
STDM
XXXX
R (Z)
NF
climatic version
4
R-open-loop ventilation, Z-closed-loop ventilation number of poles capacity, kW three phase synchronous modernized motor
27
6.2. STD - series motors with 2,500...12,500 kW capacities

STD-series synchronous turbomotors with the capacity of 2,500...12,500 kW with 50 Hz AC three phase power supply are designed to operate pumps, compressors, gas pressurizers, air blowers and other fast-running devices operated in the enclosed rooms with explosion-proof atmospheres in conditions of temperate climates. Embodiment Cooling system IM 7211, IM 7311 motors below 8,000 kW and 12.5 MW air cooling, closed- or open-loop 10 MW Motors - air cooling, closed-loop motors with closed-loop ventilation have integrated air coolers operated on fresh water (or on sea water, as greed upon with the manufacturer) in motors with open-loop ventilation, heated air is discharged through louvers in the stator casing motors with the capacity of 6,300; 8,000 kW with open-loop ventilation are manufactured with integrated coarse and fine air intake filters and ducts for air removal outside the service area closed-loop ventilation - ICW37A71 open-loop ventilation - IC31 from digital thyristor excitation systems STSN or VTE10-315-series analog thyristor exciters (on request), or from brushless exciters type BVU direct or reactance start, depending on the value of flywheel moments of driven equipment. Frequency starts from thyristor frequency converters (thyristor starter) are possible -as agreed upon with the manufacturer closed-loop ventilation - I44 open-loop ventilation - I22 S1
Cooling method Excitation system Start Protection level Rated operating conditions
Manufactured in compliance with GOST R 52776 2007 and customers specific technical requirements. Delivery set includes: motor, thermal control sensors, pressure switch sensor, foundation fastenings, mounting equipment, spare parts, operation documents. On customers request, the motor can be equipped with excitation device, soft starter SSM-HV and frequency converter HV-VFD.
Type of motor STD-2500-2R NF4 STD-2500-2R NF4 STD-2500-2Z NF4 STD-2500-2Z NF4 STD-3150-2R NF4 STD-3150-2R NF4 STD-3150-2Z NF4 STD-3150-2Z NF4 STD-4000-2R NF4 STD-4000-2R NF4 STD-4000-2Z NF4 STD-4000-2Z NF4 STD-4000-2RG NF4 STD-4000-2RG NF4 STD-5000-2R NF4 STD-5000-2R NF4 STD-5000-2Z NF4 STD-5000-2Z NF4 STD-6300-2 NF4 STD-6300-2 NF4 STD-6300-2RB NF4 STD-6300-2RB NF4
Capacity, kW 2500 2500 2500 2500 3150 3150 3150 3150 4000 4000 4000 4000 4000 4000 5000 5000 5000 5000 6300 6300 6300 6300
Voltage, V 6000 10000 6000 10000 6000 10000 6000 10000 6000 10000 6000 10000 6000 10000 6000 10000 6000 10000 6000 10000 6000 10000
Rotation speed, rpm 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
Efficiency, % 97.2 97.0 97.2 97.0 97.3 97.2 97.3 97.2 97.5 97.4 97.5 97.4 97.5 97.4 97.6 97.5 97.6 97.5 97.6 97.5 97.6 97.5
Weight, Kg 10000 10000 11100 11100 11060 11060 12300 12300 11580 11580 12920 12920 11710 11710 13700 13700 14700 14700 21390 21100 22830 22130
28
Type of motor STD-6300-2R NF4 STD-8000-2 NF4 STD-8000-2 NF4 STD-8000-2R NF4 STD-8000-2R NF4 STD-8000-2RB NF4 STD-8000-2RB NF4 STD-10000-2 NF4 STD-10000-2 NF4 STD-12500-2 NF4 STD-12500-2 NF4 STD-12500-2R NF4 STD-12500-2R NF4
Capacity, kW 6300 8000 8000 8000 8000 8000 8000 10000 10000 12500 12500 12500 12500
Voltage, V 6000 6000 10000 6000 10000 6000 10000 6000 10000 6000 10000 6000 10000
Rotation speed, rpm 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
Efficiency, % 97.6 97.9 97.7 97.9 97.7 97.9 97.7 97.8 97.9 97.9 97.8 97.9 97.8
Weight, Kg 22000 23950 23000 23950 23000 23950 23000 26520 26000 29500 28900 29500 28900
STD
XXXX
R (Z)
G (B)
NF
climatic version
4
B-with side outputs G-for EGPU drive (only for STD-4000-2GR NF4) R-open-loop ventilation, Z-closed-loop ventilation number of poles capacity, kW three phase synchronous motor
29
6.3.STD motors, special version

STD-series special synchronous turbomotors with 50 or 60 Hz AC three phase power supply are designed to operate pumps, compressors, gas pressurizers, air blowers and other fast-running devices. Embodiment Cooling system IM 7211 motors below 8,000 kW air cooling, closed- or open-loop 10,000 kW Motors - air cooling, closed-loop motors with closed-loop ventilation have integrated air coolers operated on fresh or sea water Cooling method Excitation system Start in motors with open-loop ventilation, heated air is discharged through louvers in the stator casing closed-loop ventilation ICW37A71 open-loop ventilation IC31 from digital thyristor excitation systems STSN or VTE10315-series analog thyristor exciters (on request) direct start from full mains voltage or reactance start, depending on the value of flywheel moments of driven equipment. Frequecny starts from thyristor frequency converters (thyristor starter) are possible - as agreed upon with the manufacturer closed-loop ventilation I44 open-loop ventilation I22 S1
Protection level Rated operating conditions
Manufactured in compliance with GOST R 52776 2007 and customers specific technical requirements. Delivery set includes: motor, exciter, electric heaters for motors in tropical versions, foundation fastenings, mounting equipment, spare parts for exciter and motor, operation documents.
Type of motor
Capacity, kW
Voltage, V 50 Hz
Rotation speed, rpm
Efficiency, %
Weight, Kg
STD-1000-2 4 STD-1250-2 4 STD-1600-2 4 STD-1600-2 4 STD-1600-2 4 STD-1600-2 4 STD-1600-2 4 STD-3150-2 4 STD-4000-2 3 STD-4000-2 3 STD-10000-2 3
1000 1250 1600 1750 1600 1600 1600 3150 4000 4000 10000
10000 11000 6000 6300 6600 11000 10000 11000 6600 11000 11000
3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
95.8 96.3 96.6 96.4 96.4 96.5 96.4 96.7 97.0 96.9 97.7
6980 7580 7980 7980 7980 7980 7980 12300 14700 14700 29700
STD
XXXX
climatic version
3
number of poles capacity, kW three phase synchronous motor
30
Type of motor
Capacity, kW
Voltage, V 60 Hz
Rotation speed, rpm
Efficiency, %
Weight, Kg
STD-800-3600 4 STD-1000-3600 NF4 STD-1600-3600 4 STD-1600-3600 4 STD-2500-3600 4 STD-3150-3600Z NF4 STD-10000-3600 NF4
800 1000 1600 1600 2500 3150 10000
6000 10000 6000 10000 10000 6000 6000
3600 3600 3600 3600 3600 3600 3600
95.3 95.0 96.6 96.2 96.7 96.6 97.5
5130 5600 7580 7580 11100 12285 26800
STD
XXXX
3600
R (Z)
(NF)
climatic version
4
R-open-loop ventilation, Z-closed-loop ventilation rotation speed, rpm capacity, kW three phase synchronous motor
31
6.4. STDP-series motors, explosion proof

STDP-series synchronous turbomotors with the capacity of 1,250...12,500 kW with 50 Hz AC three phase power supply are designed to operate pumps, compressors, gas pressurizers, air blowers and other fast-running devices in explosion dangerous rooms of all classes (except for explosion dangerous areas of outside installations of class V IG). Embodiment Cooling system IM 7211 air cooling, closed-loop 10,000 kW Motors - air cooling, closed-loop air is cooled with two sections of integrated air coolers operated on fresh or sea water Cooling method Excitation system Start Protection level Explosion protection type and level Rated operating conditions In motors with open-loop ventilation, heated air is discharged through louvers in the stator casing ICW37A71 from brushless exciters of BVUP series direct start from full mains voltage or reactance start, depending on the value of flywheel moments of driven equipment I44 IExpxIIT5X S1
Manufactured in compliance with GOST R 52776 2007 and customers specific technical requirements. Delivery set includes: motor, brushless excitation of BVUP series, thermal control sensors, switch of type DN 2.5, resistance level control unit BKS-3I, foundation fastenings, mounting equipment, spare parts to the motor, operation documents. On customers request, the motor can be equipped with excitation control cabinet, soft starter SSM-HV and frequency converter HV-VFD. Type of motor STDP-1250-2 NF4 STDP-1250-2 NF4 STDP-1600-2 NF4 STDP-1600-2 NF4 STDP-2000-2 NF4 STDP-2000-2 NF4 STDP-2500-2 NF4 STDP-2500-2 NF4 STDP-3150-2 NF4 STDP-3150-2 NF4 STDP-4000-2 NF4 STDP-4000-2 NF4 STDP-5000-2 NF4 STDP-5000-2 NF4 STDP-6300-2 NF4 STDP-6300-2 NF4 STDP-6300-2B NF4 STDP-6300-2B NF4 STDP-8000-2 NF4 STDP-8000-2 NF4 STDP-8000-2B NF4 STDP-8000-2B NF4 STDP-10000-2 NF4 STDP-10000-2 NF4 STDP-12500-2 NF4 STDP-12500-2 NF4 Capacity, kW 1250 1250 1600 1600 2000 2000 2500 2500 3150 3150 4000 4000 5000 5000 6300 6300 6300 6300 8000 8000 8000 8000 10000 10000 12500 12500 Voltage, V 6000 10000 6000 10000 6000 10000 6000 10000 6000 10000 6000 10000 6000 10000 6000 10000 6000 10000 6000 10000 6000 10000 6000 10000 6000 10000 Rotation speed, rpm 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 Efficiency, % 96.5 96.2 96.7 96.6 96.9 96.9 96.8 96.6 97.1 96.8 97.2 96.9 97.3 97.2 97.4 97.4 97.4 97.4 97.6 97.6 97.6 97.6 97.7 97.6 97.7 97.7 Weight, Kg 7030 7030 7630 7630 8030 8030 11150 11150 12350 12350 12970 12970 14750 14750 21600 21600 21950 21750 23000 23000 22800 23000 27000 26500 29500 28900
32
STDP
XXXX
NF
climatic version
4
with side outputs number of poles capacity, kW three phase synchronous motor, ventilated
33
6.5. SDG2 motor to operate gas pressurizers

SDG2 synchronous turbomotor with 50 or 60 Hz AC three phase power supply is designed for driving natural gas pressurizer EGPU at gas compressor plants. Embodiment Cooling system Cooling method Excitation system Protection level Rated operating conditions IM 7311 air cooling, open-loop, with fans on shaft and additional axial fan installed on casing IC31 from digital thyristor excitation systems STSN or VTE630/150T-series analog thyristor exciters (on request) direct, reactance-free asynchronous starts from full mains voltage are possible I44 S1
Manufactured in compliance with GOST R 52776 2007 and customers specific technical requirements. Delivery set includes: motor, exciter, foundation fastenings, mounting equipment, spare parts exciter and motor operation documents. On customers request, the motor can be equipped with soft starter SSM-HV and frequency converter HV-VFD.
Type of motor SDG2-12500-2R NF3.1
Capacity, kW 12500
Voltage, V 10000
cos 0,9
Rotation speed, rpm 3000
Efficiency, % 97.8
Weight, Kg 36000
SDG2
12500
NF
climatic version
3.1
open-loop ventilation number of poles capacity, kW two-pole synchronous motor to operate gas pressurizer
34
6.6. RVSD Frequency-regulated, explosion proof synchronous motor with 14,000 kW capacity
RVSD-14000-2R NF4 electric motor with open loop type ventilation is a part of frequency regulated electric drive feeding from the thyristor frequency converter. It is designed to drive centrifugal mechanisms in explosion hazard zones of the 1st and 2nd class under Russian GOST 51330.9 50 or 60 Hz AC three phase power supply. Electric motor of this type can be used at pumping plants of oil-trunk pipelines or compressor plants at gas pipe lines instead of gas-turbine motors (as an alternative to gas turbine motors with lower efficiency). The particular feature of RVSD-14000-2R NF4 is than it is possible to regulate Rotation speed from 50% to 105% (1,500-3,150 rpm), that allows supporting the required pressure in the oil pipeline and excluding excess demand energy. Embodiment Cooling system Cooling method Excitation system Start IM 7011
air cooling, open-loop IC31 from asynchronous brushless exciter with digital control system integrated in the converter direct start from full mains voltage or reactance start, depending on the value of flywheel moments of driven equipment Protection level IP44 Explosion protection type and level IExpxIIT5X. Purging and maintenance of differential static pressureinside the motor shall be effected with a pressurizer fan installed in the air treatment unit Rated operating conditions S1
On customers request, the motor can be equipped with frequency converter HV-VFD. Manufactured in compliance with GOST R 52776 2007 and customers specific technical requirements. A pressurizer fan, an air cleaning unit and a thyristor frequency converter are not included in the delivery set.
Type of motor RVSD-14000-2R NF4
Rated capacity, kW 14000
Rated voltage, V 6000
Synchronous rotation speed, rpm 1500...3150
cos 0.9
Efficiency, % 97.7
Weight, Kg 34400
RVSD
14000
NF
climatic version
4
open-loop ventilation number of poles capacity, kW frequency-regulated, explosion proof synchronous motor
35
6.7. TDS motors with 20,000 and 31,500 kW capacities

TDS turbo-motors with 50 Hz AC power supply are designed to operate high-pressure compressors at metallurgical factories. Embodiment Cooling system Cooling method Excitation system Motor start Protection level Rated operating conditions IM 7321 air-cooling, closed loop, with water air coolers ICW37A71 from digital thyristor excitation systems STSN frequency-regulated, from thyristor converter IP44 S1
On customers request, the motor can be equipped with soft starter SSM-HV and frequency converter HV-VFD. Manufactured in compliance with GOST R 52776 2007. Delivery set includes: motor, exciter, starter, foundation fastenings, mounting equipment, spare parts to exciter and motor, operation documents. Type of motor TDS-20000-2 NF4 TDS-31500-2 NF4 Capacity, kW 20000 31500 Voltage, V 10000 10000 Rotation speed, rpm 3000 3000 Efficiency, % 97.6 97.5 Weight, Kg 57300 82900
Note: weight of motors does not include weight of exciters. TDS XXXXX 2 NF
climatic version number of poles capacity, kW synchronous turbomotor
4
36
7. Salient pole synchronous motors

7.1. SDK2- and DSK-series compressor motors
SDK2- and DSK-series synchronous compressor motors with 50 or 60 Hz AC three phase power supply are designed to operate piston compressors and are used in oil refining, metallurgical, machinery and other industries. Embodiment Cooling method Excitation system Protection level Rated operating conditions IM 5710 console-type motors IM 7111 - SDK2 17 39 12F NF4 IC01 From digital thyristor excitation systems STSN or VTE10-315-series analog thyristor exciters (on request) IP10 S1
On customers request, the motor can be equipped with soft starter SSM-HV, frequency converter HV-VFD. Manufactured in compliance with GOST R 52776 2007, GOST 18200 and customers specific technical requirements. Delivery set includes: motor, thyristor exciter, thermal control sensors, foundation fastenings, device for installation and removal of rotor, spare parts, operation documents.
Type of motor SDK2-16-24-12 NF4 SDK2-16-24-12 NF4 SDK2-16-29-12 4 SDK2-16-29-12 4 SDK2-16-29-14 NF4 (4) * SDK2-16-29-14 NF4 (4) * SDK2-16-29-12 4 * SDK2-16-24-10 NF4 SDK2-16-24-10 NF4 SDK2-16-24-10 4 SDK2-16-29-12F NF4 SDK2-17-26-16 NF4 SDK2-16-36-12 NF4 SDK2-17-26-12 NF4 SDK2-17-26-12 NF4 SDK2-17-26-12 NF4 SDK2-17-26-12 4 SDK2-17-26-12 4 SDK2-17-26-12 4 SDK2-17-29-14 NF4 (4) * SDK2-17-29-14 NF4 (4) * SDK2-16-44-10 NF4 SDK2-16-44-10 4 SDK2-16-44-10 NF4 SDK2-17-39-12F NF4 SDK2-17-39-12F NF4 * 60 Hz motor
Capacity, kW 315 315 315 315 320 320 400 400 400 400 400 500 500 630 630 630 630 630 630 630 630 630 710 800 1000 1000
Voltage, V 6000 10000 3000 6000 3000 6000 6000 6000 10000 6000 6000 6000 6000 3000 6000 10000 3000 6000 6600 3000 6000 10000 6000 6000 6000 10000
Rotation speed, rpm 500 500 500 500 514 514 600 600 600 600 500 375 500 500 500 500 500 500 500 514 514 600 600 600 500 500
Efficiency, % 92.3 91.9 92.7 92.7 93.0 93.0 93.1 93.9 93.9 93.5 94.0 93.0 93.7 93.7 94.5 94.5 94.1 94.1 94.1 94.3 94.3 95.0 95.3 96.0 95.0 94.0
Weight, Kg 2460 2470 2750 2750 3130 3130 2750 2550 2670 2560 4100 3900 3250 3600 3600 3640 3550 3550 3550 4030 4030 3780 3800 3770 5930 5550
37
SDK
17 (16)
XX
YY
F (C)
NF ()
climatic version
4
C-console version (no shaft), F - one support version (flange) number of poles stator core size, cm size designation series synchronous compressor motor
Type of motor DSK 173/16-16 NF4 DSK-315-500-6 NF4 DSK-315-500-10 NF4 DSK-400-600-6 NF4 DSK-400-600-10 NF4 DSK-630-500-6 NF4 DSK-630-500-10 NF4 DSK-710-600-6 NF4 (4)
Capacity, kW 315 315 315 400 400 630 630 710
Voltage, V 3000 6000 10000 6000 10000 6000 10000 6000
Efficiency, % 92.0 92.0 92.0 94.0 95.0 94.5 94.5 95.3
Weight, Kg 3220 2460 2410 2544 2630 3400 3420 3854
DSK
XXX
YYY
6 (10)
()
NF ()
climatic version
4
modification index voltage, kV rotation speed, rpm capacity, kW synchronous compressor motor
38
7.2. SDKP2-series compressor explosion proof synchronous motors

SDKP2-series compressor explosion proof synchronous motors 50 or 60 HZ AC three phase with power supply are designed for operation in explosion dangerous areas for driving piston compressors and are used in oil refining, metallurgical, machine building and other industries. Embodiment Cooling system Cooling method IM 5710 open- or closed-loop ventilation closed-loop ventilation ICW37A81 open-loop ventilation ICW37A31 Excitation system from digital thyristor excitation systems STSN or VTE10-315-series analog thyristor exciters (on request) Explosion protection type and level IExpxIIT5 Protection level IP44 Rated operating conditions S1
On customers request, the motor is equipped with exciter, soft starter SSM-HV, frequency converter HV-VFD. Manufactured in compliance with GOST R 52776 2007, GOST 18200 and customers specific technical requirements. Delivery set includes: motor, air cooler and blowdown valve (for closed-loop ventilation), pressure switch sensors, thermal control sensors, device for rotor installation and removal, foundation fastenings, flanges (for closed-loop ventilation), spare parts, operation documents Type of motor SDKP2-16-24-12 NF4 SDKP2-16-24-12 NF4 SDKP2-16-24-12 NF4 SDKP2-16-29-12 NF4 SDKP2-16-29-12 NF4 SDKP2-16-36-14 2* SDKP2-16-36-12 NF4 SDKP2-16-36-12 NF4 SDKP2-16-29-10 NF4 SDKP2-16-29-10 NF4 SDKP2-17-26-16 NF4 SDKP2-17-26-12 NF4 SDKP2-17-26-12 NF4 SDKP2-17-26-12 NF4 SDKP2-17-31-12 NF4 SDKP2-17-31-12 NF4 SDKP2-17-31-12 NF4 * 60 Hz motor SDKP2 2 16 (17) XX YY NF ()
climatic version console design (w/o shaft) number of poles stator core size, cm size designation series synchronous motor, ventilated, compressor motor
Capacity, kW 315 315 315 400 400 400 500 500 500 500 500 630 630 630 710 800 800
Voltage, V 6000 6000 10000 6000 6000 6000 6000 6000 6000 6000 6000 6000 6000 10000 10000 6000 6000
Rotation speed, rpm 500 500 500 500 500 514 500 500 600 600 375 500 500 500 500 500 500
Efficiency, % 92.2 92.2 91.9 93.0 93.0 93.2 93.7 93.7 94.0 94.0 93.6 94.0 94.0 93.8 94.3 94.5 94.5
Ventilation cycle closed-loop open-loop open-loop closed-loop open-loop open-loop closed-loop open-loop closed-loop open-loop closed-loop closed-loop open-loop open-loop open-loop closed-loop open-loop
Weight, Kg 3700 3240 3500 4000 3540 4600 4650 4190 4000 3540 5675 5210 4740 4880 5830 5650 5180
2 (4)
39
7.3. SDN general purpose motors

SDN synchronous motors with 50 or 60 Hz AC three phase power supply are designed to operate pump drive motors, running in pumps station system and other mechanisms. Embodiment Cooling system Cooling method Excitation system Protection level Rated operating conditions IM 7311 air cooling, open-loop self-ventilation IC01 from brushless exciter with digital control system or from brushless asynchronous exciter with the possibility to control the rotation speed IP10 S1
Manufactured in compliance with GOST R 52776 2007 and customers specific technical requirements. Delivery set includes: motor, excitation system, temperature monitoring equipment, spare parts and accessories, operation documents. On customers request, the motor can be equipped with soft starter SSM-HV and frequency converter HV-VFD.
Type of motor SDN-1000-600 N3 SDN-630-750 N3 SDN-1250-1000 NF4
Capacity, kW 1000 630 1250
Voltage, V 10000 10000 6000
cos 0,9 0,9 0,9
Efficiency, % 95.0 94.63 96.0
Weight, Kg 9540 5765 8100
SDN
XXX
YYY
N, NF
climatic version
3
rotation speed, rpm capacity, kW synchronous motor
40
8. EXCITATION SYSTEMS FOR SYNCHRONOUS MOTORS 8.1. Excitation control cabinet for brushless exciters of synchronous motors (SHUVD)
Excitation control cabinet SHUVD-1E-60-6 is designed for excitation control of motors STDP, STD, SDN and similar motors with the capacity up to 31,500 kW with brushless exciters. SHUVD are manufactured on the basis of digital microprocessor regulators and highly reliable foreign-made components and ensures: automatic field injection at reactor or across-the-line starting of the motor; automatic current control of brushless exciter of synchronous motors; implementation of control functions and data; connection to the top-level of control; protection of the excitation systems equipment and motor (short-circuit protection of the inverter, off-design operation protection of the brushless exciter, protection from loss of excitation, overload protection of the motor rotor, motor protection from long-running starting operation); possibility to install a display panel with the Russian language on the front panel of the cabinet for ease of diagnostics and exciter control (option); two-channel version possible; possibility to manufacture in accordance with the required dimensions, operating conditions, and specific requirements of the customer. Protection level Climatic version Category of location IP54 NF 4
Manufactured in compliance with GOST 21558 2009 and customers specific technical requirements. Delivery set includes: control cabinet; supplying transformer OLS-1.25/6(10) N2 type -1 pcs.; set of spare parts and accessories; operation documents. Basic technical parameters: Rated voltage of exciter coil, V Rated current, Current boosting ratio, relative unit Duration of boosting, sec. Rated supply voltage: alternating, V operational, direct, V 60 6 1.7 (adjustable) 50 (adjustable) ~ 220 220
SHUVD
XXX
YYY
NF (, )
climatic version
3 (4)
rated rectified current rated rectified voltage self-cooling number in schematic design control cabinet for exciter of the motor, modernized
41
8.2. TRN 1P thyristor voltage regulator

TRN-1P-XXX-YYY-NF4 thyristor voltage regulator is designed for supplying regulated three phase voltage to stator coil of a brushless asynchronous exciter for synchronous motors STDP, STD, SDN with the capacity up to 12,500 kW for operation in the local control mode or for external setting from frequency converter (VFD). TRN 1P regulator ensures the following motor operation modes: voltage boosting in the manual regulation mode within the maximum output voltage. Excitation boosting operates in case of voltage drop on the motor stator below the setting; local control of the voltage setting in the whole regulation range; voltage setting control on the basis of the external setting; operability in case of short-term (not more than 60 s) change in the mains voltage within 50 - 140%; relay boosting time limitation. During operation in the remote control mode, regulator TRN 1 P ensures maintenance of the voltage in line with the external setting, e.g. from VFD. Selection between the local and remote operation modes is effected with a switch on the front panel of the TRN 1P cabinet. TRN 1P regulator has the following protections: overheating protection of the power section of the regulator; short-circuit protection of thyristors; phase loss protection. Manufactured in compliance with GOST 21558 2009 and customers specific technical requirements. Basic technical parameters: Rated output current, A Limit output voltage, V Current boosting ratio, min. Max. boosting duration, s, max. AC supply voltage for operating circuits (rated value), V Permissible voltage deviations, % AC supply voltage frequency, Hz Permissible frequency deviations, Hz Rated voltage for motor stator voltage measuring circuits (effective value), V Rated current for motor stator current measuring circuits (effective value), A Power consumed by the equipment: 220 V AC, kW, max. From voltage measuring transformers (per phase), VA, max. From current measuring transformers (per phase), VA, max. 0.3 1 1 20-300 380 1.4 60 220 +10, -15 50 -3, +2 100 5
TRN
XXX
YYY
NF
climatic version
4
limit output supply voltage of the exciter stator coil, V permissible long-term AC, A forced thyristor cooling number of channels thyristor voltage regulator
42
8.3. Static thyristor excitation systems for synchronous motors type STSN
Digital static thyristor excitation systems STSN are designed for power supply to excitant wiring and excitation current in synchronous electric motors of STDM, STD, SDK, SDKP, DSK, TDS, and their analogues with power control level up to 31,500 kW. Excitatory systems STSN provide excitation current control in synchronous electric motors under the following conditions: direct start; operating with frequency transformer and smooth start equipment; operating under normal and emergency conditions. STSN excitatory system functions: forced voltage min. 1.75x rated value; limited duration and period of forced operating; maintenance of excitatory current level, 1% precision level under the conditions of voltage fluctuations range 70% - 110% of rated level or rotor temperature change; limited maximum and minimum excitation current; suppression of excitation field when motor is offline, during power outages, or in presence of field suppression signal; local and remote control of excitatory current; range from minimum to maximum level; operating under the conditions of short-term (up to 60 sec) supply voltage changes from 50% to 140%; reactive stator current regulation and power ration in automatic mode; connection to top level of automatic control systems. Integrated protection systems: thyristor transformer maximum current protection; asynchronous movements protection; starter resistor overheat protection; field break protection; prolonged start protection; power supply phase outage protection; power income voltage decrease protection; power income frequency decrease protection; i2t rotor of motor overheat protection; DC chains isolation control. Protection level Climatic version Category of location from IP21 to IP54 NF, U, 3, 4
Manufactured in accordance with GOST 21558 2009 and customer's specific technical requirements. Basic technical parameters: Rated excitation current, A Rated excitation voltage, V Rectification transformer power voltage, kW 200 to 630 48 to 230 0.4
STSN
1 (2)
P ()
XXX
YYY
NF (U, )
climatic version
3 (4)
rated exciter current (rectified), A rated rectified voltage, V P forced cooling E self-cooling number of channels static thyristor system with independent power supply (auxiliary power supply via matching transformer)
43
8.4. VTE 10-315 and VTE 630/150 T series analog thyristor exciters for synchronous motors
VTE 10-315/*T NF4 (O4) series thyristor exciters with rated current of 315A are designed to supply power to the excitation coil, and to control the excitation currents of STDM, STD, SDK, SDKP and DSK series synchronous electric motors. VTE 10-315/*T NF4 (O4) series thyristor exciters can be manufactured in three versions: version 0 - standard (w/o module MR or module MRRT); version 1 with module MR; version 2 with module MRRT. VTE 630/150T NF3.1 (In=630A, Un=150V) thyristor exciter is designed for supplying power to excitation coil and excitation current control of motor SDG2 12500 2R NF3.1. VTE 10-315 and VTE 630/150T series thyristor exciters can be manufactured for similar motors on customers request. Protection level IP20
Exciters are Manufactured in compliance with GOST 24688 81 and customers specific requirements. Delivery set of exciter VTE10-315/*T NF4 (U4) includes: main module MO, anode module MA (for exciters with Un=150V and Un=230V), module with backup control system MR (for version 1, supplied on request), module with backup control system and current reverse MRRT (or version 2, supplied on request), module of starting resistors MPS, matching power transformer, set of spare pars and accessories, operation documents. Delivery set of exciter VTE 630/150T NF3.1 includes: thyristor converter cabinet, control and monitoring cabinet, starting resistor cabinet, matching power transformer, set of spare pars and accessories, operation documents. * Rated voltages (Un): 48 V, 75 V, 115 V, 150 V, 230 V Ratio of boosting current Weight (exciter and starting resistance) +transformer, kg
Type of exciter
Capacity, kW
Rated voltage, V
Rated direct current, A
Efficiency, %
Exciters for STDM, STD, SDKP, SDK, DSK VTE10-315/48 NF4 (4) VTE10-315/75 NF4 (4) VTE10-315/115 NF4 (4) VTE10-315/150 NF4 (4) VTE10-315/230 NF4 (4) 15.1 23.6 36.2 47.3 72.5 48 75 115 150 230 315 315 315 315 315 Exciters for SDG 2-12500-2 VTE-630/150 NF3.1 94.5 150 630 3.00 94.5 991+1500 1.80 1.80 1.80 1.80 1.80 91.4 93.0 94.1 94.2 95.3 350+390 431+665 505+865 603+665 643+865
VT
10
XXX
YYY
NF (U)
climatic version
4 (3.1)
connection to mains via transformer rated rectified voltage, V rated rectified current, A number of modification air self-cooling thyristor exciter
44
9. Asynchronous eXplosion prooF motors with a short circuited rotor 9.1. VAO series motors
Asynchronous explosion proof VAO motors with 50 or 60 Hz AC power supply are designed to drive pumps, fans, smoke exhausters, air blowers and other mechanisms. they are used for transfer of hydrocarbons in gas and dust hazardous mines and in explosive areas of premises referred to as explosive categories 1, 2, 3 and groups T1, T2, T3, T4 (as per electric devices installation classification). Embodiment IM 1001
Cooling system air-to-air, closed-loop ventilation Cooling method IC0151 Explosion protection type and level IExdIIBT4 and PB ExdI - motors VAO2, VAO5 IExdeIICT4 - motors VAO3 IExdIIBT4 - motors VAO 560 Protection level Rated operating conditions 2ExdIIC3 - motors VAO 800 IP54 S1
The motors are produced in compliance with GOST R 52776-2007 and individual customer performance specifications. Design of motors is protected with utility patent No. 42922. Delivery set includes: motor, thermal image temperature indicators or resistance temperature detectors, spare parts, bearing extractor (on request), operation documents. On customers request, the motor can be equipped with soft starter SSM-HV and frequency converter HV-VFD. Capacity, kW 200 250 160 200 200 250 250 315 315 315 315 400 400 400 200 160 200 200 200 250 250 250 315
Type of motor
Voltage, V
Rotation speed, rpm
Efficiency, %
Weight, Kg
VAO2-450 low voltage motors VAO2-450-200/380-2 N2 VAO2-450-250/380-2 N2 VAO2-450-160-2 N2 VAO2-450S-2 N2 (N5, F2) VAO2-450S-2 2 (5) VAO2-450-2 N2 (N5, F2) VAO2-450-2 2 (5) VAO2-450L-2 3 VAO2-450L-2 N2 (N5, F2) VAO2-450L-2 2 (5) VAO2-450-315-2D N2 VO2-450LB-2 N2 (N5, F2) VO2-450LB-2 2 (5) VAO2-450LB-2 2 (5) VAO2-450-200-2D N2 VAO2-450-160-4 N2 VAO2-450-200-4 N2 (N5) VAO2-450-200/3-4 N2 VAO2-450-200-4D N2 VAO2-450-250-4 N2 (N5) VAO2-450-250-4D N2 VAO2-450-250-4 2 VAO2-450-315-4 N2 (N5) 380 380 VAO2-450 motors 6000 6000 6000 6000 6000 6600 6000 6000 10000 6000 6000 6600 10000 6000 6000 3000 10000 6000 10000 3300 6000 3000 3000 3600 3000 3600 3000 3000 3600 3000 3000 3600 3000 3000 1500 1500 1500 1500 1500 1500 1500 1500 92.36 94.1 93.6 94.3 93.8 94.7 94.4 93.9 94.64 94.9 94.4 94.5 94.4 94.2 94.85 94.91 94.6 94.85 94.0 94.92 94.72 1765 1760 1760 1800 1800 2055 2050 2050 2350 2330 2330 2320 2080 2045 2250 2250 2160 2470 2380 2315 2780 3000 3000 94.1 94.3 2370 2370
45
Type of motor VAO2-450-315-4 2 VAO2-450-400-4 N2 (N5) VAO2-450-315-4D N2 VAO2-450-400-4D N2 VAO5-450-200-4 N2 VAO5-450-200-4 N5 VAO5-450-250-4 N2 VAO5-450-250-4 N5 VAO5-450-315-4 N2 VAO5-450-315-4 N5 VAO5-450-400-4 N2 VAO5-450-400-4 N5
Capacity, kW 315 400 315 400 200 200 250 250 315 315 400 400
Voltage, V 3300 6000 10000 10000 VAO5450 motors 6000 6000 6000 6000 6000 6000 6000 6000 VAO2560 motors
Rotation speed, rpm 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500
Efficiency, % 95.04 95.21 94.6 94.8 94.0 94.0 94.3 94.3 94.7 94.7 95.0 95.0
Weight, Kg 2505 4330 2680 3100 2140 2090 2285 2240 2585 2530 3155 3105
VAO2-560-400-8 N2 VAO2-560-400-4 N2 (N5) VAO2-560-400-2D N2 VAO2-560-500-4 N2 (N5) VAO2-560-500-2 N2 VAO2-560-500-2D N2 VAO2-560-630-4 N2 (N5) VAO2-560-630-2 N2 VAO2-560-630-2D N2 VAO2-560-800-6 N2 VAO2-560-800-4 N2 VAO2-560-800-2 N2 VAO2-560-800-2D N2 VAO2-560-1000-2 N2 VAO5-560-400-2D N2 VAO5-560-500-2 N2 VAO5-560-500-2D N2 VAO5-560-630-2D N2 VAO5-560-630-2 N2 VAO2-630-800-4 N2 (N5) VAO2-630-800-6 N2 VAO3-450S-2 N2 IIC VAO3-450-2 N2 IIC VAO3-450LA-2 N2 IIC VAO3-450LB-2 N2 IIC VAO-560-1000-2D N2 (NF4) VAO-560-1250-2 N2 (NF4)
400 400 400 500 500 500 630 630 630 800 800 800 800 1000 400 500 500 530 630 800 800 200 250 315 400 1000 1250
6000 6000 10000 6000 6000 10000 6000 6000 10000 6000 6000 6000 10000 6000 VAO5560 motors 10000 6000 10000 10000 6000 VAO2630 motors 6000 6000 VAO3450 motors 6000 6000 6000 6000 VAO 560 motors 10000 6000
750 1500 3000 1500 3000 3000 1500 3000 3000 1000 1500 3000 3000 3000 3000 3000 3000 3000 3000 1500 1000 3000 3000 3000 3000 3000 3000
94.2 95.21 92.33 94.71 93.51 93.14 95.82 93.75 93.57 94.82 95.26 94.66 94.34 94.94 94.8 95.5 95.18 95.5 95.8 95.26 94.82 94.1 94.3 94.4 94.9 95.9 96.3
4130 4440 4190 5200 4150 4380 5370 4400 4850 4950 4750 4870 5280 5250 3490 3400 3810 4100 3865 5000 5000 1760 1800 2050 2330 4980 5060
46
Type of motor VAO-560-1250-2D N2 (NF4) VAO-560-1600-2 N2 (NF4) VAO-560-1600-2D N2 (NF4) VAO-560-2000-2 N2 (NF4)
Capacity, kW 1250 1600 1600 2000
Voltage, V 10000 6000 10000 6000 VAO 800 motors
Rotation speed, rpm 3000 3000 3000 3000
Efficiency, % 95.9 96.1 96.3 96.4
Weight, Kg 5458 5453 5620 5695
VAO-800-630-12 NF4 VAO-800-630-12 NF4 (for mill drive) VAO-800-630-10 NF4 VAO-800-800-10 NF4 VAO-800-1000-12 NF4 VAO-800-1250-16NF4 Advanced development: VAO5-560-4 N2. VAO 2 (3, 5) XXX
630 630 630 800 1000 1250
6000 6000 6000 6000 6000 6000
500 500 600 600 500 375
94.8 95.15 94.6 94.9 94.7 95.5
12755 12755 12000 12000 11530 17645
LA (S, M, LB)
YY
N (F, NF, T)
2 (3, 4, 5)
IIC
sub-group sign
climatic version voltage 10 kV number of poles stand size height of rotation axis, mm series explosion proof, asynchronous, ventilated
47
9.2. V-2500 and V-5000 motors

Asynchronous motors VAO-2500 and VAO-5000 with a three phase AC 50 Hz power supply are designed as drives of horizontal oil pumps and other quick-moving mechanisms in areas of explosion hazard and for external class 2 machinery (in compliance with GOST R 51330.9). Embodiment IM 1001
Cooling system air-to-air system, closed-loop ventilation system Cooling method ICA 0151 Explosion protection type and level VAO-2500-6000-2NF4 - IExdIIBT3 Protection level Rated operating conditions VAO-2500/10000-2 N2, VAO-5000-6000-2NF4, VAO-5000/10000-2 NF4 (N2) - IExdIIBT4. IP54 S1
Manufactured in compliance with GOST 52776 2007, GOST 51330.0, GOST R 51330.1 and technical requirements. Delivery set includes: motor, spare parts, maintenance documentation. On customers request, the motor can be equipped with soft starter SSM-HV and frequency converter HV-VFD. Capacity, kW 2500 2500 5000 5000
Type of motor VAO-2500-6000-2 NF4 VAO-2500/10000-2 N2 VAO-5000-6000-2 NF4 VAO-5000/10000-2 NF4 (N2)
Voltage, V 6000 10000 6000 10000
Efficiency, % 96.8 96.6 96.8 97.3
Weight, Kg 9460 9460 14890 13000
VAO
XXXX
YYYY
NF(N)
climatic version
4 (2)
category of location according to GOST 15150
number of poles voltage, V rated capacity, kW explosion proof, asynchronous, ventilated
48
9.3. VASO-series explosion proof vertical motors

VASO asynchronous explosion proof vertical motors with AC 380 V, 50 Hz power supply are designed to operate as a gearless drive of air coolers and water towers. The motors may be used as part of electric speed controlled drives, in which Rotation speed is controlled by frequency converters (on special request). Magneto-liquid sealer can be used in VASO-series motors. Cooling system Cooling method Explosion protection type and level Protection level Rated operating conditions air cooling IC0141 IIExdIIBT4; IExdeIIBT4 or IExdeIICT3 - VASO4 motor IExdIIBT4 or IExdeIICT4 VASO5 motor IP54 or IP55. In case of magnetoliquid sealer installation in motors VASO4, protection level is IP55 S1
Manufactured in compliance with GOST 52776-2007, GOST R 51330.0 and customer's specific technical requirements.
Delivery set includes: motor, spare parts and operational documents. Upon Customer's request, the motors may be delivered with magneto-liquid sealants. On customers request, the motor can be equipped with soft starter SSM-HV and frequency converter HV-VFD. Capacity, kW 6,5 6,5 13 15 22 22 30 30 30 30 37 37 37 37 55 75 55 75 75 90 Efficiency, % 82.0 82.0 89.7 89.7 89.7 90.4 90.3 90.3 86.18 91.1 89.33 90.5 91.5 90.93 91.76 92.33 90.94 91.85 90.87 92.3 Weight, Kg 200 200 510 510 1110 780 1225 1225 1020 870 1580 1316 960 1530 1840 2105 1940 2300 3630 2765
Type of motor VASO4-6,5-12 N1 (F1, NF1)* VASO4-6,5-12 N1 (F1, NF1)* VASO4-13-12 N1 (F1, NF1)** VASO4-15-12 N1 (F1, NF1)* VASO4-22-14 N1 (F1, NF1)** VASO5-22-14 N1 (F1, NF1)**** VASO4-30-14 N1 (F1, NF1)** VASO4-30-14 N1 (F1, NF1)** VASO4-30-32 N1 (F1, NF1)* VASO5-30-14 N1 (F1, NF1)**** VASO4-37-24 N1 (F1, NF1)*** VASO4-37-14 N1 (F1, NF1)** VASO5-37-14 N1 (F1, NF1)**** VASO5-37-24 N1 (F1, NF1)* VASO5-55-24 N1 (F1, NF1)* VASO5-75-24 N1 (F1, NF1)* VASO4-55-24 N1 (F1, NF1)*** VASO4-75-24 N1 (F1, NF1)* VASO4-75-34 N1*** VASO4-90-24 N1*
Voltage, V 380 380 380 380 380 380 380 660 380 380 380 380 380 380 380 380 380 380 380 380
Rotation speed, rpm 500 500 500 500 428.6 428.6 428.6 428.6 187.5 428.6 250 428.6 428.6 250 250 250 250 250 176.5 250
Embodiment IM 4011 IM 4031 IM 4333 IM 4333 M 9633 M 9633 M 9633 M 9633 M 9633 M 9633 M 9633 M 9633 M 9633 M 9633 M 9633 M 9633 M 9633 M 9633 M 9633 M 9633
* motors marked for explosion proof protection as IExdIIBT4 ** motors marked for explosion proof protection as IExdIIBT4 and IExdeIICT3 *** motors marked for explosion proof protection as IExdeIIBT4 and IExdeIICT3 **** motors marked for explosion proof protection as IExdIIBT4 and IExdeIICT4
49
VASO
4 (5)
XX
YY
N (F, NF)
climatic version
1
number of poles capacity, kW series explosion proof, asynchronous, special, ventilated
50
9.4. VAOV series vertical motors

VAOV series asynchronous vertical motors with three phase 50 HZ AC power supply are designed to operate shore pumps to maintain formation pressure (3,000 rpm) and oil-trunk pipeline booster pumps (1,500 rpm). Embodiment Cooling system Cooling method Explosion protection type and level Protection level Rated operating conditions IM 4011 air-to-air, closed-loop ventilation IC0151 IExdIIBT4 IP54 S1
Manufactured in compliance with GOST R 52776 2007 and customers specific technical requirements. Delivery set includes: motor, monitoring sensors, spare parts, bearing extractor (upon the request), and operation documents. On customers request, the motor can be equipped with soft starter SSM-HV and frequency converter HV-VFD. Type of motor VAOV-200-2 N2 VAOV-250-2 N2 VAOV-315-2 N2 VAOV-400-2 N2 VAOV-500-2 N2 VAOV-400-4 NF1 VAOV-400-4D NF1 VAOV-800-4 NF1 VAOV-800-4D NF1 VAOV-1250-4 NF1 VAOV-1250-4D NF1 VAOV-2000-4 NF1 VAOV-2000-4D NF1 VAOV-2000-6D NF1 Capacity, kW 200 250 315 400 500 400 400 800 800 1250 1250 2000 2000 2000 Voltage, V 6000 6000 6000 6000 6000 6000 10000 6000 10000 6000 10000 6000 10000 10000 Rotation speed, rpm 3000 3000 3000 3000 3000 1500 1500 1500 1500 1500 1500 1500 1500 1000 Efficiency, % 93.02 93.45 94.2 94.74 95.4 95.0 94.5 95.7 95.4 96.0 95.9 96.6 96.2 96.45 Weight, Kg 1967 2022 2200 2450 2900 3500 3450 6510 7085 8515 8500 10300 10250 15000
VAOV
XXX
2 (4, 6)
NF (N)
climatic version
1 (2)
voltage 10 kV number of poles capacity, kW explosion proof, asynchronous, ventilated, vertical
51
10. EXPLOSION PROOF, THREE PHASE ASYNCHRONOUS MOTORS WITH A SHORT CIRCUITED ROTOR 10.1. DAZO4 - series ventilated motors
Asynchronous ventilated motors DAZO4-series with three phase AC 50 Hz power supply are designed to operate pumps, air blowers, fans, smoke exhausters, mills and other mechanisms operating in temperate climates, after such application is confirmed. Embodiment Cooling system Cooling method Protection level Rated operating conditions IM 1001. Motors are connected with the driven equipment by couplings, transferring no thrust loads of the motor shaft air cooling, self-ventilation mode IC0161 IP44, DAZO4M motor - IP54 S1
Manufactured in compliance with GOST R 52776 2007 and customers specific technical requirements. Delivery set includes: motor, spline, foundation fastenings, bearing extractor (upon the request), thermal control sensors, spare parts, operational documents. On customers request, the motor can be equipped with soft starter SSM-HV and frequency converter HV-VFD. Capacity, kW 1000 1250 1250 1600 1600 2000 800 1000 1000 1000 1250 1250 1600 630 630 630 800 800 1000 1000 1250
Type of motor
Voltage, V 1500 rpm
Rotation speed, rpm
Efficiency, %
Weight, Kg
DAZO4-560-4D N1 DAZO4-560-4 N1 DAZO4-560Yk-4D N1 DAZO4-560Yk-4 N1 DAZO4-560Y-4D N1 DAZO4-560Y-4 N1 DAZO4-560-6D N1 DAZO4-560-6 N1 DAZO-560-79-6 N1 (to drive mills) DAZO4-560Yk-6D N1 DAZO4-560Yk-6 N1 DAZO4-560Y-6D N1 DAZO4-560Y-6 N1 DAZO4-560-8D N1 DAZO4-560-8 N1 DAZO4-560-8 N1 DAZO4-560Yk-8D N1 DAZO4-560Yk-8 N1 DAZO4-560Y-8D N1 DAZO4-560Y-8 N1 DAZO4-560-1250-8N1 DAZO4-560-10 N1 (with 2 terminal boxes) DAZO4-560-10 N1 DAZO4-560-10 N1 DAZO4-560-10D N1 DAZO4-560Yk-10 N1
52
10000 6000 10000 6000 10000 6000 1000 rpm 10000 6000 6000 10000 6000 10000 6000 750 rpm 10000 6000 3000 10000 6000 10000 6000 6000 600 rpm
1500 1500 1500 1500 1500 1500 1000 1000 1000 1000 1000 1000 1000 750 750 750 750 750 750 750 750
95.0 95.5 95.3 95.8 95.6 96.0 94.9 95.5 95.0 95.2 95.8 95.5 96.0 94.4 94.7 95.2 94.7 95.0 95.0 95.3 95.5
4520 4840 5200 5570 5580 6040 4610 4930 6700 5310 5630 5670 6140 5785 5875 4690 6275 6325 6660 6690 7472
400 400 500 500 630
3000 6000 6000 10000 6000
600 600 600 600 600
94.77 93.6 94.1 93.8 94.6
4200 4200 4500 4510 5260
Type of motor DAZO4-560Yk-10D N1 DAZO4-560Y-10 N1 DAZO4-560Y-10D N1 DAZO4-560-12 N1 DAZO4-560-12 N1 DAZO4-560-12D N1 DAZO4-560Yk-12 N1 DAZO4-560Yk-12D N1 DAZO4-560Y-12 N1 DAZO4-560Y-12D N1
Capacity, kW 630 800 800 315 400 400 500 500 630 630
Voltage, V 10000 6000 10000 500 rpm 6000 6000 10000 6000 10000 6000 10000
Rotation speed, rpm 600 600 600 500 500 500 500 500 500 500
Efficiency, % 94.3 94.9 94.6 92.9 93.4 93.1 93.9 93.6 94.4 94.1
Weight, Kg 5280 5620 5650 4200 4500 4500 5250 5260 5600 5610
DAZO
560
XXX
YY
N
climatic version
1
number of poles rated capacity, kW (stator core size) height of rotation axis, mm modernized series asynchronous closed ventilated motor
53
10.2. DAO-type ventilated motors

DAO-type asynchronous ventilated motors with 50Hz AC three phase power supply are designed for driving the equipment under heavy-duty start conditions in explosion proof and non-fire atmosphere. Embodiment Cooling system Cooling method Protection level Rated operating conditions IM 1001 air cooling IC0161 IP54 S1
Manufactured in compliance with GOST R 52776 2007 and customers specific technical requirements. Delivery set includes: motor, key, foundation fastenings, bearing extractor, thermal control sensors, spare parts, operation documents. On customers request, the motor can be equipped with soft starter SSM-HV and frequency converter HV-VFD. Capacity, kW 1250 1250 2000 2000
Type of motor DAO-1250-750-6 N1 DAO-1250-1000-6 N1 DAO-2000-500-6 N1 DAO-2000-1000-10 N1
Voltage, V 6000 6000 6000 10000
Efficiency, % 95.5 95.0 95.7 95.6
Weight, Kg 17300 11640 15000 15350
Advanced development: DAO-2000-1000-6N1. DAO XXXX YYY 6 (10) N

climatic version voltage, kV rotation speed, rpm capacity, kW asynchronous ventilated motor
1
54
10.3. AOD-type ventilated two-speed motors

AOD-type asynchronous ventilated two-speed motors with three phase AC 50 Hz power supply are designed to operate forced-draft mechanisms of thermal power stations. Embodiment Cooling system Cooling method Protection level Rated operating conditions IM 1001. Motors are manufactured with two stator coils operated separately air cooling IC0161 IP54 S1
Manufactured in compliance with GOST R 52776 2007 and customers specific technical requirements. Delivery set includes: motor, foundation fastenings, bearing extractor, thermal control sensors, spare parts, operation documents.
Type of motor AOD-800-8/10 N1 AOD-800Y-6/8 N1 AOD-1000/500-8/10 N1 AOD-1250/725-8/10 N1
Capacity, kW 630/400 1600/1000 1000/500 1250/725
Voltage, V 6000 6000 6000 6000
Synchronous rotation speed, rpm 750/600 1000/750 750/600 750/600
Efficiency, % 93.6/93.4 95.0/94.7 94.6/93.97 95.13/94.62
Weight, Kg 9330 11770 19000 19000
AOD
800
Y ()
6/8 (8/10)
N
climatic version
1
number of poles motor size designation (stator core size) height of rotation axis, mm asynchronous ventilated two-speed
AOD
XXXX/XXX
8/10
N
climatic version
1
number of poles capacity, kW asynchronous ventilated two-speed
55
10.4. AZO - series closed-ventilation motors

AZO - series asynchronous closed ventilated motors with three phase AC 50HZ power supply are designed to operate compressors, pumps and high inertia mass mechanisms. Embodiment Cooling system Cooling method Protection level Rated operating conditions IM 1001 air-cooling, self-ventilation mode IC0151 IP44 S1
Manufactured in compliance with GOST R 52776 2007 and customers specific technical requirements. Delivery set includes: motor, thermal image temperature indicator, oiler, spare parts, bearing extractor (on the request), operation documents. On customers request, the motor can be equipped with soft starter SSM-HV and frequency converter HV-VFD. Capacity, kW 200 250 315 400
Type of motor AZO-450S-2 N1 (2) AZO-450-2 N1(2) AZO-450L-2 N1 (2) AZO-450L-2 N1 (2)
Voltage, V 6000 6000 6000 6000
Efficiency, % 94.1 94.3 94.3 94.5
Weight, Kg 1810 1850 1840 2160
AZO
450
S (M, LA, LB)
N ()
climatic version
1 (2)
number of poles stator core size height of rotation axis, mm asynchronous closed-ventilation motor
Type of motor AZO-450-200-4 N2 AZO-450-200-4D N2 AZO-450-250/660-2 N2 AZO-450-250-4 N2 AZO-450-300-4 N2 AZO-560-500-4 N2 * AZO-560-500-2 N2 * AZO-560-630-6 2 * Liquid oiling AZO XXX -
Capacity, kW 200 200 250 250 300 500 500 630
Voltage, V 6000 10000 660/380 6000 6000 6000 6000 6600
Efficiency, % 94.85 94.0 94.58 94.87 94.72 95.0 92.05 95.1
Weight, Kg 2275 2440 1620 2500 2820 4700 3900 4950
YYY
N ()
climatic version
1(2)
voltage 10 kV number of poles capacity, kW height of rotation axis, mm asynchronous closed-ventilation motor
56
10.5. DAB special asynchronous motors

Asynchronous special DAB motors with three phase AC 50Hz power supply are designed to operate the screw compressors of drilling machines and other mechanisms. Embodiment Cooling system Cooling method Protection level Rated operating conditions IM 1001 air cooling IC0151 IP44 S1
Manufactured in compliance with GOST R 52776 2007 and customers specific technical requirements. Delivery set includes: motor, thermal image temperature indicator, oiler, spare parts, bearing extractor (on the request), operation documents. Type of motor DAB-450S-2 NF2 DAB-450-2 2 DAB-450-2 N2 Capacity, kW 200 200 250 Voltage, V 6000 3300 6000 Rotation speed, rpm 3000 3000 3000 Efficiency, % 94.1 93.3 93.9 Weight, Kg 1760 1910 1935
DAB
450
S ()
NF (N, )
climatic version
2
number of poles stator core size height of rotation axis, mm asynchronous motor for drilling rig
10.6. DA4 asynchronous motors

DA4 asynchronous motors with three phase AC 50Hz power supply are designed to operate pumps and other mechanisms. Embodiment Cooling system Cooling method Protection level Rated operating conditions IM 1001 air cooling, open-loop ventilation IC01 IP23 S1
Manufactured in compliance with GOST R 52776-2007 and customers specific technical requirements. Delivery set includes: motor, thermal control sensors, spare parts, operation documents. On customers request, the motor can be equipped with soft starter SSM-HV and frequency converter HV-VFD. Type of motor DA4-560-8D N3 DA4-560-8D N3 Capacity, kW 630 1250 Voltage, V 10000 10000 Rotation speed, rpm 750 750 cos 0.79 0.8 Efficiency, % 94.9 95.4 Weight, Kg 5300 6150
DA
560
(N)
N
climatic version
3
voltage 10 kV number of poles motor size (stator core size) height of rotation axis, mm series asynchronous motor
57
10.7. VASV vertical water-cooled special motors

VASV asynchronous vertical special motors are designed to provide gearless drive to cooling tower fans from the mains of alternating 6,000 V current. Embodiment Cooling system Protection level Rated operating conditions IM 3731 water-cooled (closed-loop water recirculation system is installed inside the stator) IP54 or IP55 S1
Manufactured in compliance with GOST R 52776 2007 and customers specific technical requirements. Delivery set includes: motor, spare parts, and operation documents. On customers request, the motor can be equipped with soft starters SMM-HV and frequency converters HV-VFD. Type of motor VASV-200-52 N1 Capacity, kW 200 Voltage, V 6000 Rotation speed, rpm 115.4 Efficiency, % 86.7 Weight, Kg 11000
VASV
200
52
N
climatic version
1
number of poles capacity, kW asynchronous vertical water-cooled special motor
10.8. DASO vertical motors

DASO asynchronous vertical motors with three phase AC 380V 50Hz power supply are designed to operate as a gearless drive for air-coolers and fans of cooling towers. Embodiment Cooling system Protection level Rated operating conditions IM 9633 air cooling, open-loop ventilation IP54 S1
The motors can be manufactured with the use of acid-resistant coating, glass-ceramic tribolubrication, and magnetoliquid sealer. Manufactured in compliance with GOST R 52776 2007 and customers specific technical requirements. Delivery set includes: motor, spare parts, and operation documents. On customers request, the motor can be equipped with electric heaters, temperature monitors, and magnetoliquid sealer. Capacity, kW 50 75
Type of motor DASO-50-34 N1 DASO-75-34 N1
Voltage, V 380 380/660
Rotation speed, rpm 176.5 176.5
Weight, Kg 2000 3400
DASO
XX
34
N
climatic version
1
number of poles capacity, kW asynchronous, special, air-cooled motor
58
10.9. Special asynchronous motors with variable frequency drive

10.9.1. Explosion proof asynchronous squirrel-cage motor DARB 1200 6 NF2
With marking 23 in compliance with GOST R 52350.7 is designed for variable frequency drives for main equipment of drilling rigs (drill winch, mud pumps, and rotor). Embodiment IIM1003 in compliance with GOST 2479 with one operating cone shaft end, in compliance with GOST 12081 with key, in compliance with GOST 23360 with two bearing shields air cooling I 36 in compliance with GOST 20459 GOST 14254, GOST 17494: terminal box - IP56; cooling air inlet and outlet - IP23; forced ventilation fan motor - IP 44 Rated operating conditions S1
Cooling system Cooling method Protection level
The motor is manufactured with grease-lubricated SKF roller bearings. Design of bearing blocks enables refilling of grease without motor disassembly. The motor is equipped with resistance temperature detectors with unique sensor curve 100P, measuring the temperature of stator coil and bearing blocks. To prevent the stator coil moistening, the motor is equipped with flexible heating elements, installed directly on the coil. The motor is reversible and enables operation at any rotation direction in the whole range of rotation speed regulation. The following is delivered complete with the motor: spare parts, including bearing extractor (on the customers request), and operation documents. The motor is Manufactured in compliance with GOST R 52776, GOST R 52350.0, and GOST R 52350.7.
Type of motor DARB-1200-6 NF2
Capacity, kW 1200
Voltage, V 660
Rotation speed, rpm 1000 to 2000
Current frequency, HZ 50
Power factor 0.84
Efficiency, % 95.0
Weight, kg 3800
DARB
1200
NF2
climatic version and location category
number of poles capacity, kW asynchronous regulated motor for driving main equipment of drilling rigs
59
10.9.2. Asynchronous squirrel-cage DARG 3500 8 UM4

The motor is designed for operation as a part of electric propulsion system of a vessel with propulsion and steering column (PSC). The motor enables operation on vessels with the unlimited navigating zone, including vessels of the ice navigation category of the maximum class Icebreaker 6. The motor is reversible and enables operation at any rotation direction in the whole range of rotation speed regulation by changing the phase, value and frequency of the supplied power provided by the frequency converter. Embodiment IM1001 in compliance with GOST 2479 on feet, with one operating cylindrical shaft end, in compliance with GOST 12080 with key, in compliance with GOST 23360 with two end shields air cooling through water-air cooler coolant sea water S1
Cooling system Cooling method Rated operating conditions
The following is delivered complete with the motor: spare parts and operation documents. The motor is Manufactured in compliance with GOST R 52776 and Russian Maritime Register of Shipping Rules of Technical Inspection for Building of Ships and Fabrication of Materials and Items for Ships.
Type of motor DARG-3500-8 4
Capacity, kW 3500
Voltage, V 21800
Current frequency, HZ 50
Power factor 0.85
Efficiency, % 97.0
Weight, kg 14900
DARG
3500
U 4
climatic version and location category
number of poles capacity, kW asynchronous, regulated propulsion motor
60
11. HIGH-SPEED VARIABLE-FREQUENCY ELECTRIC DRIVES EPRV

High-speed variable-frequency electric drives are designed for direct-driven high-speed machines, including centrifugal pressurizers used as a part of electrically driven gas pumping units. High speed frequency regulated electric motor and rotor on the magnetic suspension and GST inverter (frequency converter) with the required components are parts of the electric drives. If necessary, the electric drive can be equipped with automatic control system upon the Customers request Embodiment Cooling system Cooling method Protection level Rated operating conditions Noise level IM 1001 air cooling, open-loop IC31 motor - IP23 frequency converter - IP20 S1 max. 85 dBA
High-speed variable-frequency electric drives are produced under the license of TMEIC (Toshiba Mitsubishi - Electric Industrial Systems Corporation), Japan. Delivery set includes: motor, high-voltage frequency converter, automatic control system, spare parts, operation documents.
Type of motor EPRV-4000-8200 NF4 EPRV-6300-8200 NF4 EPRV-8000-8200 NF4
Capacity, kW 4000 6300 8000
Voltage to the inverter, kW 3.0 3.3 3.9
Rotation frequency range, % of rated 50-105 50-105 50-105
EPRV
XXXX
8200
NF
climatic version
4
rotation speed of electric motor, rpm capacity, kW high-speed variable-frequency electric drive
61
12. MOTORS FOR MAIN PUMPING UNITS OF NUCLEAR PLANTS 12.1. Vertical closed asynchronous motor DAVZ-8000-6 AM U5
Vertical closed asynchronous motor DAVZ-8000-6 AM U5 with three phase AC 50 Hz power supply is designed as a drive for main circulation pump type GCNA-1713 for nuclear plants power units. Embodiment Cooling system Cooling method Protection level Rated operating conditions IM 8721 air cooling, closed loop ICW37A71 IP55 S1
Manufactured according to TU 3381-025-59162910-2009. Delivery set includes: : motor, maintenance documentation, package of maintenance documents for components, blueprints file, spare parts, tool kit.
Type of motor DAVZ-8000-6 U5
Operating mode Cold water mode Hot water mode
Capacity, kW 8000 5300
Voltage, V 6000
Weight, Kg 52250
DAVZ
8000
U
climatic version
5
equipped with sea water coolers for nuclear power plants number of poles rated capacity, kW asynchronous vertical closed motor
62
12.2. Asynchronous two-speed motor DAVDZ-7100/2800-10000-6/8 AM U5

Asynchronous vertical closed two-speed motor DAVDZ with squirrel-cage rotor; three phase AC 50 Hz power supply is designed as a drive of main circulation pump type GCNA-1391 for power units type VVER of nuclear plants. Embodiment Cooling system Cooling method Protection level Rated operating conditions IM8221 air cooling, closed-loop ICW37A71 IP55 S1
Manufactured according to TU 3381-026-59162910-2009. Delivery set includes: motor, motor maintenance documents, supporting equipment maintenance documents, blueprints file, spare parts, tool kit.
Type of motor DAVDZ-7100/2800-10000-6/8 U5
Operating mode Cold water mode Hot water mode
Capacity, kW 7100/2800 5000
Voltage, V 10000
Rotation speed, rpm 1000/750 1000
Efficiency, % 95.0/93.0 94.5
Weight, Kg 45500
DAVDZ
7100/2800
10000
6 /8
U
climatic version
5
equipped with sea water coolers for nuclear power plants number of poles rated voltage, V rated capacity, kW asynchronous vertical two-speed closed motor
63
ELeCtrICaLLY DrIVen gas ComPressor UnIts
64
13. ELECTRICALLY DRIVEN GAS COMPRESSOR UNITS 13.1. EGPU electrically driven 4.0 MW gas compressor units
EGPU-4.0/8200-56/1.26 (1.44)-R Lysva-VOSTOK electrically driven gas compressor units with high-speed controlled electric motors have a capacity of 4,000 kW, a rotation speed of 8,200 rpm, and NC-4/56-1.26 and NC- 4/56-1.44 STC SV (08 2A) centrifugal pressurizers. Rotors of electric motor and pressurizer have magnetic bearings. Designed to compress and transport natural gas through main gas pipelines. Replace existing EGPU units, which have 280-type centrifugal pressurizers, reduction gear, and STM 4000-2 (manufactured by LTGZ) and STD 4000-2NF4 electric motor drives. Basic technical data and Delivery set Climatic version Category of location Atmosphere type Rated operation mode VTU VJ 33352 05 NF (ambient air temperature range from - 60C to +40C) 4 II (atmosphere of production facilities) S1
The unit enables to install pressurizers and electric motors onto existing base plates without significant unit adjustments. EGPU 4.0 / 8200 56 / 1.26 (1.44) R Lysva-VOSTOK
symbolic notation of the unit delivered for reconstruction of compressor workshops at compressor stations rated pressure step-up ratio (compression ratio) rated operation pressure, ATM rotation speed, rpm rated capacity, MW electrically driven gas compressor unit
13.2. EGPU electrically driven gas compressor units of 6.3 MW

EGPU-6.3/8200-56/1.44-R Kedr electrically driven gas compressor units have high-speed controlled 6,300 kW electric motors, a rotation speed of 8,200 rpm, and 208-21-1LSM centrifugal pressurizers. Rotors of electric motor and pressurizer have magnetic bearings. Designed to compress and transport natural gas through main gas pipelines. EGPU-6.3/8200-56/1.44-R Kedr unit replaces the existing EGPU units, which have 280-type centrifugal pressurizers, reduction gear and STM 4000-2 (manufactured by LTGZ) and STD 4000-2NF4 electric motor drives Basic technical data and Delivery set Climatic version Category of location Atmosphere type VTU VJ 32987 04 NF (ambient air temperature range from - 60C to +40C) 4 II (atmosphere of production facilities)
The unit enables to install pressurizers and electric motors onto existing base plates without significant unit adjustments EGPU 6.3 / 8200 56 / 1.44 R Kedr
65
13.3. EGPU electrically driven 8.2 MW gas compressor units

EGPU-8.0/10000-56/1.44-R, Lysva MB 8.2 electrically driven gas compressor units have high speed controlled 9,100 kW electric motors, a rotation speed of 8,600 rpm, and a monoblock centrifugal pressurizer. Rotor of the unit has magnetic bearings. The monoblock is mounted to the base plate and coupled to a high voltage input switchboard and a pipeline pressurizer platform. Designed to compress and transport natural gas through main gas pipelines. EGPU-8.0/10000-56/1.44-R Lysva MB 8.2 unit replaces existing EGPU units, which have 280-type centrifugal pressurizers, reduction gear and STM 4000-2 (manufactured by LGTZ) electric motor drives. Basic technical data and Delivery set Climatic version Category of location Atmosphere type EGPU 8.2 / 8600 VTU VJ 35013 06 NF (ambient air temperature range from - 60C to +40C) 4 II (atmosphere of production facilities) 56 / 1.44
delivered for reconstruction of compressor workshops at compressor stations rated pressure step-up ratio (compression ratio) rated operation pressure, ATM rotation speed, rpm rated capacity, MW electrically driven gas compressor unit
13.4. EGPU electrically driven gas compressor units of 12.5 MW (non-controlled)

EGPU-12.5/3000-76/1.23-R Lysva non-controlled electrically driven gas compressor units with electric motors of 12,500 kW capacity, rotation speed 3,000 rpm and centrifugal pressurizer 370 -18- 2 are designed to compress and transport natural gas through main gas pipelines. Used for revamp of existing EGPU, where synchronous motor STD 12500 2 NF4 is replaced with SDG-12,500-2-NF3.14 synchronous motor, and standard flow tube for 30 mln.m3/ a day is installed in the existing pressurizer 370-18-2. Developed for revamp of the Bubnovskaya compressor station of Gazprom transgaz Volgograd. Basic technical data and Delivery set Climatic version Category of location Atmosphere type EGPU 12.5 / 3000 VTU VJ 35011 06 NF (ambient air temperature range from - 60C to +40C) 4 II (atmosphere of production facilities) 76 / 1.23 R Lysva
66
13.5. EGPU electrically driven gas compressor units of 12.5 MW (controlled)

EGPU-12.5/5200-76/1.23-R Lysva electrically driven gas compressor unit with controlled, high-speed, frequency-regulated electric motor of 12,500 kW capacity, rotation speed 5,200 rpm and centrifugal pressurizer are designed to compress and transport natural gas through main gas pipelines. Used for revamp of existing EGPU, where STD-12500-2-NF4 synchronous motor is replaced with the synchronous motor, produced by TMEIC (Toshiba Mitsubishi-Electric Industrial Systems Corporation, Japan). Standard flow tube for 30 mln.m3/ a day is installed in the existing pressurizer 370-18-2; and the step-up gear is used as an intermediate bearer for the drive line, connecting motor and pressurizer. Developed for revamp of the Bubnovskaya compressor station of Gazprom transgaz Volgograd.
Basic technical data and Delivery set Climatic version Category of location Atmosphere type
VTU VJ 35012 06 NF (ambient air temperature range from - 60C to +40C) 4 II (atmosphere of production facilities)
EGPU
12.5
5200
76
1.23
Lysva
symbolic notation of the unit
delivered for reconstruction of compressor workshops at compressor stations rated pressure step-up ratio (compression ratio) rated operation pressure, ATM rotation speed, rpm rated capacity, MW electrically driven gas compressor unit
67
13.6. Set of equipment for reconstructing electrically driven gas compressor units of 12.5 MW
Set of equipment (KMCH) EGPU 12.5/3000 76/1.44 (1.32) P, O with electric motor of 12,500 kW capacity, rotation speed 3,000 rpm and SPCH 370-2Z-3 pressure-tight changeable flow tube is designed to compress and transport natural gas through main gas pipelines. KMCH is used to reconstruct existing EGPU, where STD-12500 2 NF4 electric motor with closed-loop ventilation is replaced with STD-12500 2R NF4 electric motor with open-loop ventilation, and a pressure-tight changeable flow tube (SPCH) is installed into the cylinder of centrifugal pressurizer 370-18-2.
Basic technical data and Delivery set Climatic version Category of location Atmosphere type
VTU VJ 35014 06 NF (ambient air temperature range from - 60C to +40C) 4 II (atmosphere of production facilties)
KMCH
EGPU
12.5
3000
76
1.44 (1.32)
rated compression ratio
rated operation pressure, ATM rated rotation speed of electric motor, rpm rated capacity, MW electrically driven gas compressor unit set of equipment
68
TRANSFORMING EQUIPMENT
69
14. TRANSFORMING EQUIPMENT 14.1 High voltage frequency converters HV-VFD

High voltage frequency converters are designed to control the rotation speed and rotation moment in synchronous and asynchronous AC electrical motors. Frequency converters HV-VFD can be used to adjust frequency in electric drives of water and oil pumps (including the submersible pumps), ventilators, compressors (including piston compressors), high-speed electrically driven gas pumping machines, exhausters, blowers, extruders, ventilators etc, used in systems of powerful compressors and turbogenerators smooth start at oil, gas, metallurgical, paper-making facilities and the energy plants, on marine vessels, open sea rigs, coast line rigs and for other applications. Rated voltage, V Output frequency Frequency regulation precision 125% Overrun regimen functioning Incoming power factor Efficiency Cooling Control system Protection level Atmosphere type Technical parameters of HV-VFD-xxx-6 NF4 Motor capacity, kW Rated voltage, V Rated output current, A Size: HxWxD, mm Weight, kg Technical parameters of HV-VFD-xxx-10 NF4 Motor capacity, kW Rated voltage, V Rated output current, Size: HxWxD, mm Weight, kg 315 40 400 40 500 40 630 800 1000 1250 93 1600 105 2000 10000 120 2500 160 2800 3150 4000 5000 375 6300 8000 31500 40 53 61 70 93 105 120 160 315 400 500 630 710 800 1000 1250 1600 6000 215 250 325 375 430 600 800 1000... 1700 2000 2500 3150 4000 5000 6300 8000... 14000
3000*, 3300*, 6000, 6600*, 10000, 11000* (technical parameters of HV-VFD with the voltage parameters given are provided upon request) up to 200 Hz 0,5% 1 min over 95% over 97% forced air cooling sensor-free vector control + PWM (pulse width modulation) IP20 II (manufacturing facilities atmosphere)
330026431000 2955
4200x2643x1000 3409
Upon request Upon request
53 61 70 3,300x2,643x1,000 2,955
215 250 325 4,200x2,643x1,000 3,409
430 600... 2400 Upon request Upon request
Note: technical parameters are agreed during the project planning VFD HV XXX YYY NF
climatic version rated voltage, V rated capacity, kW high voltage frequency converter
4
70
14.2 High voltage soft starters SSM-HV

High voltage soft starters are designed for starting synchronous and asynchronous motors under smooth voltage rise and motor current limitation at a set level. High voltage soft starters SSM-HV can be used for soft starting of water and oil pumps (including the submersible pumps), fans, compressors (including piston compressors), exhausters, blowers, extruders, starting of low power sources (diesel generators, long power lines, etc), etc, used at oil, gas, metallurgical, paper-making facilities and the energy plants, on marine vessels, open sea rigs, coast line rigs and other applications. SSM-HV for 8,000-31,500 kW motors ensures the motor start by underfrequency relay. Rated voltage, V Frequency, Hz Current range, A Protection level Atmosphere type 3000*, 3300*, 6000, 6600*, 10000, 11000*, 13800*, 15000* (* technical parameters of SSM-HV and voltage parameters are provided upon request) 50/60 2 60-2,500 in long-term regimen IP21 II
SSM-HV can be used as a system component or separately, with different options, including linear and/or shunt contactors, power switcher, fuses, motor protection relay, control systems, etc. Complex multi-motor systems with soft start can be based on SSM-HV. Technical parameters of SSM-HV-xxx-6 NF4 Motor capacity, kW Rated voltage, V Rated output current, A Size: HxWxD, mm Weight, kg Technical parameters of SSM-HV-xxx-10 NF4 Motor capacity, kW Rated voltage, V Rated output current, A Size: HxWxD, mm Weight, kg 500 630 800 1000 1250 1600 2000 2500 2800 200 2600x2300x1340 2133 2133 3150 10000 400 Upon request Upon request Upon request 4000 5000 6300 8000 10000 12500 20000 31500 315 400 500 630 710 200 915x915x2315 554 800 1000 1250 1600 2000 2500 3150 4000 6000 400 915x915x2315 554 5000 6300 8000 10000 12500 Upon request Upon request Upon request
600 1778x915x 2315 951
Note: technical parameters are agreed during the project planning.
SSM
HV
XXX
YYY
NF
climatic version
4
rated voltage, V rated capacity, kW high voltage soft starter
71
TraCtIon eLeCtrICaL eqUIPment
72
15. Traction electrical equipment 15.1 GST traction alternators

The GST synchronous salient alternators are used to convert the mechanical energy of diesel locomotives into electric energy, and to supply power to direct current electric traction motors through a rectifying module. The alternators are mounted to the diesel locomotives haul Embodiment Cooling method IM 1305 - GST 1050 1000 NF2 IM 1309 other units IC01 (self-ventilation) - GST 1050 1000 NFL2 IC37 (independent ventilation) other units cooling air is taked from outside through air filters GST 1400 1500 N2 (NFL2) - Independent, through clip rings other units - Independent, from single-phase exciter type VST generator GST 1050 1000 NF2 has an ancillary stator coil for power supply of auxiliary and excitation systems electric drives of diesel-locomotive shunters I21 GST 1050 1000 NF2: stator coil - H, rotor coil - F, slip rings - GST 1400 1000 N2 (NF2): stator and rotor coil - F, slip rings - GST 1400 1500 N2 (NF2): stator and rotor - , slip rings min. F GST 2800 1000 N2: stator and rotor coil F, slip rings - S1
Excitation
Protection level Insulation class
Rated operating conditions
Comply with GOST 2582 and Manufactured in compliance with: GST 1050 1000 NF2 - TU3381 042 05810695 2004; GST 1400 1000 N2 (NF2) - TU16 05810695 023 95; GST 1400 1500 N2 (NF2) - TU3381 135 05810695 2009; GST 2800 1000 N2 - TU16 05810695 011 93. The embodiment of the generators is protected by utility model patent No. 32268. Certificates of conformity: GST 2800 1000 N2 - No. SSFJT RU. CT03.B.08109; GST 1400 1000 N2 (NF2) - No. SSFJT RU. CT03.B.08110. Delivery set includes: an alternator, spare parts, operation documents.
Type of alternator GST 1050-1000 NF2 GST 1400-1000 N2, NF2 GST 1400-1500 NF2 GST 2800-1000 N2 GST XXXX
Active power, kW 1050 1400 1400 2800 YYYY
Voltage, V 1000/505 280/175 280/175 580/360 N (NF)

climatic version
Rotation speed, rpm 1000 1000 1500 1000 2

Efficiency, % 94.0/94.5 95.8/95.5 95.8/95.0 95.9/95.0
Weight, kg 4500 5130 4000 6000
rotation speed, rpm capacity, kW synchronous traction alternator
73
15.2 GPT-840-750N2 direct current generator

The GPT-840-750N2 direct current generator is designed to supply power to traction motors and is a component of TEM-18 locomotives. Embodiment Cooling method Excitation Protection level Insulation class Rated operating conditions IM 9809 IC01 independent IP00 F S1
Comply with GOST 2582 and Manufactured in compliance with TU3355 091 05810695 2004. Delivery set includes: generator, spare parts, operation documents. Efficiency % 94.3
Type of generator GPT-840-750 N2 GPT 840
Capacity, kW 840 750
Rated voltage, V 636/870 N

climatic version
Current, A 1320/966 2
Weight, kg 4850
rotation speed, rpm capacity, kW direct current motor generator
74
15.3 ASTM 2800/600-1000 N2 synchronous traction unit

ASTM 2800/600-1000 N2 synchronous traction unit is designed to supply power to traction motors through the rectifying module. It also supplies power to excitation systems for auxiliary systems of locomotives and power consumers, and to the electric circuits of passenger train cars. Unit structure Embodiment Cooling method Excitation Protection level Insulation class Climatic version Category of location Rated operating conditions traction and auxiliary synchronous generators combined in a single casing IM 1305 or IM 1309 IC37 independent IP21 F, slip rings N 2 S1
Comply with GOST 2582 and Manufactured in compliance with TU16 05810695 040 2004. Delivery set includes: unit, spare parts, operation documents. Auxiliary generator Type of generator Rated capacity, kW with power supplying w/o power supplying Rated value of linear voltage, V with power supplying w/o power supplying Rated value of current (phase), A with power supplying w/o power supplying Rated Rotation speed, rpm Efficiency, % Weight, kg Traction generator 2470 2800 580/465 580/366 21300/21650 21520/22400 1000 95.5/95.0 7350 Power supply coil 600 21200 150 1000 91,0 Auxiliary power supply coil 171 260 400 400 405 565
ASTM
2800
600
1000
N
climatic version
2
rotation speed, rpm capacity of auxiliary generator, kW capacity of traction generator, kW modernized synchronous traction unit
75
15.4 ASTG 2800/400-1000 N2 and ASTG2 2800/400-1000 N2 synchronous traction units

ASTG 2800/400-1000 N2 synchronous traction unit is designed for diesel units of main line cargo locomotives 2TE25K with commutator motors EDU133Tz, and as an upgrade for previously manufactured locomotives ASTG 2800/400-1000 N2 synchronous traction unit is designed to feed asynchronous traction motors through back-to-back module, to feed selfexcitation systems and power consumers of supporting systems and cargo locomotives equipped with asynchronous motor drive (2TE25 and TE25A locomotives). Unit structure Embodiment Cooling method Excitation Protection level Insulation class Rated operating conditions traction and auxiliary synchronous generators combined in a single casing IM 1309 IC37 independent IP21 stator coils of ASTG2 unit F stator coils of ASTG, and rotors and slip rings of ASTG and ASTG2 units S1
Comply with GOST 2582 and Manufactured in compliance with: ASTG2 2800/400-1000 N2 - TU3381-112-05810695-2008. Conformity certificate: ASTG2 2800/400-1000 N2 - No. SSFJT RU. CT03.B.07571. Delivery set includes: unit, spare parts, operational documents.
Type of generator
Generator traction auxiliary traction auxiliary 2 2800 /
Capacity, kW 2800 400 2800 400 400 -
Voltage, V 580/366 400 1450 400 1000
Rotation speed, rpm 1000 1000 1000 1000 N

climatic version
Efficiency, % 95.5/95.0 91.0 95.5 91.0 2
Weight, kg
ASTG-2800/400-1000 N2
7350
ASTG2-2800/400-1000 N2
7350
ASTG
category of location rotation speed, rpm capacity of the auxiliary generator, kW capacity of traction generator, kW design number synchronous traction unit
76
15.5 VST exciters

The VST synchronous traction exciters are designed to excite traction generators of locomotives. The exciter is an inverted one-phase synchronous alternating current machine with salient poles. Embodiment Cooling method Excitation Protection level Insulation class Rated operating conditions IM 1103 IC01 independent, up to 110 V IP21 F Armature, Poles, Slip rings S1
Comply with GOST 2582 and Manufactured in compliance with N16-05810695-012-93. Conformity certificate SSFJT RU. CT03.B.00292D Delivery set includes: exciter, spare parts, operational documents.
Type of exciter VST 16-3300 NF2 VST 26-3300 N2 (NF2) VST XX -
Active power, kW 16 26 3300 N (NF)

climatic version rotation speed, rpm
Voltage, V 220/230 215/287 2

Rotation speed, rpm 1700/3300 2470/3300
Efficiency, % 72,0 76,0
Weight, kg 355 360
active capacity, kW synchronous traction exciter
77
15.6 EDU 133 traction motors

The EDU 133 NF1 traction four-pole direct current motors are designed to drive the wheel pairs of locomotives. Embodiment Cooling method Excitation Protection level Insulation class Rated operating conditions MOS rollers and frame suspension. Motors are equipped with plug-in roller bearings. Design of seals for armature bearings prevents leaking of grease from bearings and entry of dust and moisture. IC17 series IPX5 armature F poles S1
Comply with GOST 2582 and Manufactured in compliance with TU16 05810695 035 97. Conformity certificate: EDU 133TR - No. SSFJT RU. CT03.B.08073. Delivery set includes: motors (6 pcs), spare parts, operation documents Type of motor EDU-133-C NF1 EDU-133-C NF1 EDU-133- NF1 EDU-133- NF1 EDU-133-P NF1 EDU-133-P NF1 EDU-133- NF1 EDU-133- NF1 Active power, kW 414 414 414 414 Rated voltage , V Rated current, A 890/577 890/577 890/577 890/577 Rotation speed, rpm Efficiency, % 92.0 92.0 92.0 92.0 Weight, kg
506/780 506/780 506/780 506/780
600/2320 600/2320 600/2320 600/2320
3350 2950 3100 3100
EDU
133
C(R, K, P)
NF
climatic version
1
C - circulation type of lubrication system; P - lubricating pad system; K - MOS roller; R - frame suspension adjusting interphase connecting rod design number universal electric motor
78
15.7 EDU 136 traction motors

EDU 136R NF1 DC traction motor with laminated frame is designed to drive wheel pair of TEP 70 main- line diesel locomotives and other motorized tipcarts. Taking into account its overall and linkage dimensions and performance characteristics the motor is replaceable by EDU 133 R motor. Ventilation of motors is of independent forced type. Method of cooling is ICA 17. Type of motor EDU 136 NF1 Active power, kW 414 Rated voltage , V 506/780 Rated current, A 890/577 Rotation speed, rpm 600/2320 Efficiency, % 92.0 Weight, kg 2650
EDU
136
NF
climatic version
1
climatic version
frame suspension design number universal electric motor
79
15.8 DAT asynchronous traction motors

DAT-350-6 NF1, DAT-470-8 NF1 asynchronous traction motors with short-circuit rotor to drive wheels pairs of main line six-axle cargo locomotives of series 2TE25T, TE25T with capacity of 2,500 kW in the section and locomotives of series 2TE35, TE35 with capacity of 3,500 kW in the section (only DAT-470-8 NF1) with traction AC power transmission. Motors are equipped with elements for thrust suspension with the use of motor thrust bearings. Embodiment IM 9403 design of motor bearings seals prevents leaking of grease from bearing blocks and entry of dust and moisture from both inside and outside. IC17 from synchronous traction generator through static frequency converter based on voltage invertor on IGBT transistors with maximum pulse-width modulation of 1.5 kHz IPX5 H S1
Cooling method Power supply Protection level Insulation class Rated operating conditions
Comply with GOST 2582 and Manufactured in compliance with TU3355 114 05810695 2006. Conformity certificate for DAT 350 6 NF1 - No. SSFJT RU. CT 03.A.06119. Delivery set includes: motor, rotation velocity sensors and temperature sensors, spare parts, operation documents. Type of motor DAT-350-6 NF1 DAT-470-8 NF1 Capacity, kW 350 470 Voltage, V 800/1410 909/1410 Phase current, 470/306 417 Rotation speed, rpm 2300 2380 Efficiency, % 92.3 92.3 Weight, kg 2350 2300
DAT
XXX
NF
climatic version
1
number of poles capacity, kW asynchronous traction motor
80
15.9 4PNJ-200MA direct current motors

4PNJ-200MA direct current motors are designed to drive the blowing of braking resistors in locomotives. Embodiment Cooling method Excitation Protection level Insulation class Climatic version Category of location Rated operating conditions IM 2003 IC01 series IP23 H NF 2 S1
Comply with GOST 2582 81 and Manufactured in compliance with TU16 05810695 045 99. Conformity certificate No. SSFJT RU. CT 03.B.06787. Delivery set includes: motor, spare parts, operation documents.
Type of motor 4PNJ-200MA 4
Rated capacity , kW 60 PN J
Rated voltage , V 340 200
Rated current, 197

modification
Efficiency, % 89.4
Weight, kg 350
length of the core stamping dimension for railway transport protected with self-ventilation series designation
81
15.10 DTK-800M N1 Direct-current traction motor

Six-pole direct-current traction motor is designed to drive sets of wheels of DC electric passenger locomotives EP2K with overhead system rated voltage of 3 kW. Motor is manufactured with plug-in type roller bearings. Seal design of armature bearings prevents oil bleeding from bearings and entry of dust and moisture in bearings both from inside and outside. Embodiment Cooling method Excitation Protection level Insulation class frame suspension IC17 series IPX5 H
Comply with GOST 2582 and Manufactured in compliance with TU3355 122 05810695 2007. Delivery set includes: motors (6 pcs), spare parts, operation documents
Type of motor Rated operating conditions Rated capacity, kW Rated voltage, V Rated armature current, Rated Rotation speed, rpm Efficiency, % Maximum rotation speed, rpm Weight, kg DTK 800 N
climatic version modernized hourly capacity of traction motor, kW direct-current traction motor
DTK-800 N1 S2 (60 min) 800 1500 (3000/2) 565 945 94.2 1720 3850 1
S1 720
510 980 94.2
82
15.11 DTK-810M NF1 direct-current traction motor

Six pole direct-current traction motor is designed to drive sets of wheels of DC main line cargo locomotives 2ES6 with overhead system rated voltage of 3 kW. Motor is manufacture with plug-in type roller bearings. Seal design of armature bearings prevents oil bleeding from bearings and entry of dust and moisture in bearings both from inside and outside. Embodiment Cooling method Excitation Protection level Insulation class thrust suspension IC17 independent IPX5 H
Comply with GOST 2582 and Manufactured in compliance with TU3355 015 59162910 2008. Delivery set includes: motor (8 pcs), spare parts, operation documents.
Type of motor Rated operating conditions Rated capacity, kW Rated voltage, V Rated current, Rated Rotation speed, rpm Efficiency, % Maximum rotation speed, rpm Weight, kg DTK 810 N
climatic version hourly capacity of the traction motor, kW rotational traction motor
DTK-810 N1 S2 (60 min) 810 1500 (3000/2) 575 750 94.25 1800 4800 1
S1 745
525 770 94.5
83
15.12 DPT direct current motors

DPT direct current motors are designed to operate the compressor units of locomotives Embodiment Cooling method Protection level Insulation class IM 1003 IC01 IP22 H
Comply with GOST 2582 and Manufactured in compliance with TU16 05810695 046 98. Delivery set includes: motor, spare parts, operation documents. Conformity certificate: No. SSFJT RU. CT03.B.06785
Type of motor DPT-25 NF2 DPT-25 NF2 DPT-37 NF2 DPT XX
Excitation mixed series mixed NF
Capacity, kW 25 25 37 2
Voltage, V 110 110 110
Rated current, 276 276 400
Weight, kg 550 550 550
category of location climatic version capacity, kW direct current motor
84
15.13 5SG, 6SG, 7SG starter-generators

5SG, 6SG, 7SG starter-generators are designed to start-up diesel generators and to operate as an auxiliary generator of the locomotive. Embodiment Cooling method Excitation Protection level Insulation class Rated operating conditions IM 1003 IC01 generator mode - independent starter mode - successive IP21 H starter (breakaway mode and motoring mode) - S2 (10 sec) generator - S6 and S1
Comply with GOST 2582 and Manufactured in compliance with: 5SG N2 (UF2, 2) - TU16 05810695 041 98; 6SG N2 - IBJK.527612.019TU; 7SG N2 - TU3355 109 05810695 2005. Certificate of conformity No. SSFJT RU. CTOZ.B.06786 for 5SG. Declaration of conformity No. SSFJT RU.CTOZ.B.00156D for 6SG. Delivery set includes: starter-generator; spare parts, operation documents. Type of motor 5SG NF2 (N2, 2) 6SG N2 7SG N2 5 (6, 7) SG Operating conditions S1 S6 S1 S6 S1 N (NF, )
climatic version starter-generator design number
Capacity, kW 50 62/32 60 70/40 55 2
Armature voltage, V 110 110 110 110 110
Maximum load duration, % 100 50 100 50 100
Curent, A 455 564/291 546 636/364 500
Rotation speed, rpm 1050/3333 1050/3333 1050/3300 1050/3300 800/2300
85
15.14 DAVT280-15-4/6/12 asynchronous traction motor

DAVT280-15 asynchronous explosion proof three-speed traction motor with a short-circuit rotor is designed to drive mine self-propelled cars with load-carrying capacity of 15 tons, working in gaseous-and- dusty mines where potash and shale are extracted. Embodiment IM 2001 with grease-lubricated rolling bearings. Bearing blocks have devices for grease removal and refilling without motor disassembly IC40 IP54 H S4
Cooling method Protection level Insulation class Rated operating conditions
Comply with GOST R 52776 2007 and Manufactured in compliance with TU16 05810695 062 2000. Delivery set includes: motor, operation documents.
Type of motor DAVT280-15-4 N2 (N5) DAVT280-15-6 N2 (N5) DAVT280-15-12 N2 (N5) DAVT 280
Number of poles 4 6 12 15
Capacity, kW 22 46 23 X
Voltage, V 660 660 660
Rotation speed, rpm 1500 1000 500 N

climatic version
Power factor 0.967 0.921 0.727 2 (5)
Efficiency, % 79.9 82.1 83.6
Weight, kg 930 930 930
category of location number of poles car load capacity, tons height of rotation axis, mm asynchronous explosion proof traction motor
86
15.15 DATE-170 and DAT-170 asynchronous traction motors

DATE-170-4N2 asynchronous, squirrel-cage traction motor is designed for driving mounted wheels of the lead and other subway cars types 81-720, 81-721, 81-740, 81-741. DAT-170-4N2 asynchronous, squirrel-cage traction motor is designed for driving mounted wheels of the lead and other subway cars types 81-760/761. Embodiment Power supply Cooling method Protection level Insulation class Rated operating conditions M 9703 from frequency converter and voltage inverter with formation of voltage curve on the principle of pulse-width modulation at voltage rise rate of 1 kV/s IC01 motor - IP20 input equipment - IP54 H S2 (60 min)
Comply with GOST R 52776 2007, GOST 2582 and Manufactured in compliance with TU3355 077 05810695 2003. Delivery set includes: motor, operation documents.
Type of motor DATE-170-4 N2 DAT-170-4 N2 DATE 170
Capacity, kW 170 170 4
Voltage, V 530 530
Current frequency of the stator, Hz 43 43 N

climatic version
Rotation speed, rpm rated/max 1290/3600 1290/3600 2
Efficiency % 92.0 92.0
Weight, kg 805 780
category of location number of poles capacity, kW asynchronous traction motor for electric locomotives
87
15.16 AMVR-37 asynchronous motor for motor-fan

AMVR-37 asynchronous three phase current motor with an external rotor is designed to operate axial motor-fans cooling water and oil in locomotives diesel motors. Embodiment Insulation class Rated operating conditions vertical H S3 (50%)
Comply with GOST 2582 and Manufactured in compliance with TU3324 102 05810695 2007. Delivery set includes: motor, operation documents Type of motor AMVR-37-U3 Rated capacity, kW 37 Rated voltage, V 400 Rotation speed, rpm 1500 Efficiency, % 92 Weight, kg 144
AMVR
37
U
climatic version
3
capacity, kW asynchronous integrated for motor-fan with controlled Rotation speed
88
15.17 Kicking coils

15.17.1 DSF-1L N2 power line filter kicking coil for subway cars
DSF-1L N2 power line filter kicking coil is designed to operate as a part of an asynchronous drive to decrease pulsation of current consumed from power mains and for installation on lead and other subway cars. Cooling method Protection level Insulation class Climatic version Category of location IC40 kicking coil - IP00 terminal box - IP54 H N 2
Comply with GOST 9219 and Manufactured in compliance with TU3459 093 05810695 2005. Delivery set includes: motor, operation documents. Description of parameter Rated voltage, V Rated Curent, A Maximum curent, A Induction under current 1000 A, mH Weight, not exceeding, kg Overall dimensions: length, mm width, mm height, mm Value 750 470 1100 8 1270 1140 880 460
15.17.2 DS-2 smoothing kicking coil

DS-2 NF smoothing kicking coil is designed for reduction of current pulsation In the circuit of a one phase rectifier energizing auxiliary power consumers of the locomotive. Cooling method Protection level Insulation class Climatic version Category of location Rated operating conditions IC40 (self-ventilated) IP00 F N 3 S1
Delivery set includes: kicking coil, data sheet. Description of parameter Rated voltage, V Rated Curent, A Mains frequency, Hz Induction under current 30 A, mH Weight, not exceeding, kg Overall dimensions: length, mm width, mm height, mm 410 255 350 Value 150 100 60...200 15 85
89
15.18 Set of electric equipment and automation for locomotives

15.18.1 PK-1000L - series electropneumatic contactors
PK-1000L - series electropneumatic contactors are designed to perform switchover operations in power circuits of direct current traction electric motors on locomotives. Protection level Climatic version Category of location IP00 N, NF, 3
Manufactured in compliance with GOST 9219 and TU3457 050 05810695 2004. Conformity certificate No.SSFJT RU. CE 06.BV.06311. Delivery set includes: contactor; spare parts, operation documents. Type of contactor P-1146L P-1148L P-1218L P-1416L P-1616L Contacts of main circuit Rated voltage of insulation, V Rated cut-off current, A Number of poles 1000 1000 1 1000 1000 1 Contacts of auxiliary circuit Rated voltage, V Rated Curent, A Contacts embodiment Weight, kg Note: c - closing contact, o - opening contact 1000 6.3 2c 1o 18 1000 6.3 1c 2o 18 1000 6.3 1c 2o 22 1000 6.3 2c 1o 27 1000 6.3 2c 1o 32 1000 500 2 1000 500 4 1000 500 6
Description of parameter
1 (2, 4, 6)
1 (4)
6 (8)
embodiment of auxiliary contacts
L
manufacturer's index
symbolic notation based on rated current value number of switched circuits notation of series pneumatic contactor
90
15.18.2 PPK-8000L-series electropneumatic switches

PPK-8000L-series electropneumatic switches are designed to switch over de-energized electric circuits of direct current traction motors, and are used as reversing gear or braking switches. Protection level Climatic version Category of location IP00 N, NF, 3
Comply with GOST 9219 and Manufactured in compliance with TU3457 053 05810695 2005. Conformity certificate No. SSFJT RU. CE 06.B.06310. Delivery set includes: switch, spare parts, operation documents. Type of switch PPK-8023L 900 Contacts of main circuit Rated Curent, A Rated voltage, V Rated Curent, A Rated voltage of gate coil, V Rated value of air pressure, MPa PPK 8 02 (04, 06, 12) 1000 75 2 Pneumatic drive 75 0.5 2 (3, 4)
embodiment number of switched circuits notation of series pneumatic cam-operated switch
Description of parameter Rated voltage of insulation, V
PPK-8042L 900 1000 110 2 110 0.5 L

manufacturer's index
PPK-8064L 900 1000 110 2 110 0.5
PPK-8122L 900 900 110 2 110 0.5
Contacts of auxiliary circuit
91
15.19 DPT-196M traction motor

DPT-196M-N2 direct current traction motor is designed to convert the generators electric power into mechanical energy for movement of tractor DET 320 and its modifications.. Embodiment Cooling method Protection level Rated operating conditions IM 1109 IC37 (independent ventilation) IP20 S1
Comply with GOST R 52776 2007 and Manufactured in compliance with TU3355 094 05810695 2004. Delivery set includes: motor, spare parts, operation documents.
Type of motor DPT-196 N2
Capacity, kW 196
Rated voltage , V 300
Curent, A 710
Rotation speed, rpm, rated/max. 420/2250
Efficiency % 90
Weight, kg 2550
DPT
196
N
climatic version
2
modification capacity, kW direct current motor
15.20 Privod-TRL1 set of traction electric equipment for trolleybuses with reostatic-contactor control systems
Privod-TRL1 set of traction electric equipment for trolleybus Trolza 5275 05 is used as a traction electric drive on trolleybuses with reostatic-contactor control systems. Comply with GOST 9219. Delivery set includes: interference-suppressing choke RP-1 N2, switch box PK-1 N3, resistor bank BR-1 N2, resistor bank BR 2 N2, trolleybus driver controller KVT-1 N2, contactor reverse controller RK-1 N2, cam-shaft controller KG-1 N3, operation documents. Description of parameter Rated voltage of power circuit, V Rated voltage of control circuit, V Average current in start-up mode, not exceeding, A Weight of set, not exceeding, kg Value 550 24 350 1270
92
15.21 DPT-110 traction motor for trolleybus

DPT-110 N2 direct current traction motor is designed for trolleybuses with relay-contactor control systems. Embodiment Cooling method Excitation Protection level Insulation class Rated operating conditions IM 1103 IC01 mixed at air inlet - IP33 at air outlet - IP20 H S2 (60 min)
Comply with GOST 9219 and Manufactured in compliance with TU 3355 099 05810695 2004. Delivery set includes: motor, spare parts, operation documents.
Type of motor DPT-110 N2
Capacity, kW 110
Rated voltage , V 550
Current, 220
Rotation speed, rpm, rated/max 1430/3900
Efficiency % 90.9
Weight, kg 700
DPT
110
2 category of location
climatic version capacity, kW DC traction motor
93
16. GOST CONVENTIONS 16.1 Embodiment (in compliance with GOST 2479)
Designation IM 1001 IM 3731 IM 4011 IM 5710 IM 7011 IM 7111 IM 7211 IM 7311 IM 7321 IM 8721 9633 Description Machines with feet, two bearing shields and one cylindrical shaft end Machines without feet and two bearing shields, with a flange inaccessible from the back side, with one cylindrical shaft end Machines without feet and two bearing shields; free cylindrical shaft end is directed downwards; flange on the stand is accessible from the back side, located on the side of the free shaft end Machines without bearing shields, with a stand on raised feet and base plates without shaft end Machines with pillar type bearing, with feet and base plate with one cylindrical shaft end Machines with one pillar type bearing on raised feet and base plates with one flanged shaft end Machines with two pillar type bearings on a common base plate, with one cylindrical shaft end Machines with pillar type bearings on raised feet and base plate with one cylindrical shaft end Machines with pillar type bearings on separate plates with one cylindrical shaft end Machines with vertical shaft, with thrust plate over rotor, with flywheel, with one cylindrical shaft end Machines of special embodiment with two bearing shields, on feet in the horizontal plane, with one cone shaft end
16.2 Cooling method (in compliance with GOST 20459)

Designation IC01 IC31 IC40 IC0141 IC0151 IC0161 ICW37A31 ICW37A71 ICW37A81 Description Protected machine with self-ventilation; the fan is located on the machine's shaft Cooling by fans installed in the rotor shaft, inlet and outlet channels (louvers), or air treatment units installed on the machine casing Enclosed machine with self-cooling without external fan Enclosed machine with finned or smooth stand, ventilated by external fan installed ion the machines shaft Air-cooling of machines by self-ventilation using a cooler integrated in the machine and using ambient air Air-cooling of machines by self-ventilation using a cooler installed on the machine and using ambient air Air-cooling of machines by self-ventilation using a cooler installed on the machine and using water Enclosed machine with air cooling and integrated water cooler; water in the cooler is circulated by a separate pump independent of the cooled machine or from water system Enclosed machine with air cooling and built-on water cooler; water in the cooler is circulated by a separate pump or from water system
16.3 Protection level (in compliance with GOST 14254)

Designation IP10 IP20 121 IP22 IP23 IP33 IP44 IP54 IP55 Description Protected against foreign solids with the diameter 50 mm; no water ingress protection Protected against foreign solids with the diameter 12,5 mm; no water ingress protection Protected against foreign solids with the diameter 12,5 mm and against vertically falling water drops Protected against foreign solids with the diameter 12,5 mm and against vertically falling water drops, when the enclosure is at the angle of 15 Protected against foreign solids with the diameter 12,5 mm and against water falling as rain Protected against foreign solids with the diameter 2,5 mm and against water falling as rain Proetcted against foreign solids with the diameter 1,0 mm and against complete sprinkling Dust-protected against foreign solids and protected against complete sprinkling Dust-protected against foreign solids and protected against water jets
94
16.4 Climatic versions (in compliance with GOST 15150)

Designation N NF F T U Climatic version of products Products are designed for operation on shore, rivers and lakes For macroclimatic areas with temperate climates For macroclimatic areas with temperate and cold climates For macroclimatic areas with cold climates For macroclimatic areas with both dry and wet tropical climates For all macroclimatic areas on land, except for macroclimatic areas with extremely cold climates (general climatic version)
16.5 Categories of location (in compliance with GOST 15150)

Designation 1 2 Characteristics For open air operations (impacted by set of climatic factors specific to the macroclimatic area) For operations under the shed or within premises (space) where air temperature and humidity fluctuations differ only insignificantly from the open air fluctuations, and there is relatively free access to outside air -- for example, in tents, cargo platforms, trailers, metal containers without thermal insulation, and in the shell of category 1 packaged products (no direct sun light and precipitation impact) For operations in closed premises (space) with natural ventilation and no artificially controlled climates, where air temperature and humidity fluctuations and sand and dust impacts are significantly smaller than in the open air -- for example, in metal premises with thermal insulation, brick and concrete premises, wooden premises (no precipitation or direct sun light impact; significantly reduced wind forces; significantly reduced or no impact from scattered sunlight and moisture condensate) For operations in premises (space) with artificially controlled climates -- for example, in closed heated premises or in cooled and ventilated industrial and other types of premises, including well- ventilated underground premises (no impact from precipitation, direct sun light, wind, or dust and sand; significantly reduced or no impact from scattered sunlight and moisture condensate) For operations in premises (space) with high humidity (for example, in non-heated and non- ventilated underground premises, including mines, cellars, in the soil; on vessels or boats that may have water for long periods of time, or have frequent moisture condensation on the walls and ceiling, namely in some cargo holds, certain textile and hydrometallurgical industry workshops, and others)
16.6 Rated operation mode (in compliance with GOST 18311)

Designation S1 Description Long-term operation
16.7 Explosion protection types and levels (in compliance with GOST 51330)
Designation IExdIIBT4 IExdeIIBT4 IExdeIICT3 IExdeIICT4 IExpxIIT5X PB Exdl 2ExdIIC3 Description Explosion proof electrical equipment, group II, sub-group IIB, with the type of explosion protection explosion proof enclosure d for temperature class T4 Explosion proof electrical equipment, group II, sub-group IIB, with the type of explosion protection explosion proof enclosure d, provided by protection of type , for temperature class 4 Explosion proof electrical equipment, group II, sub-group IIC, with the type of explosion protection explosion proof enclosure d, provided by protection of type , for temperature class 2 Explosion proof electrical equipment, group II, sub-group IIC, with the type of explosion protection explosion proof enclosure d, provided by protection of type , for temperature class T4 Explosion proof electrical equipment of group II with the type of explosion protection casing filling or purging under Px excess pressure valve, for temperature class T5; manufacturer does not provide installation of protective devices Mining explosion proof electrical equipment of group I with the type of explosion protection explosion-proof enclosure d Explosion proof electrical equipment of advanced protection against explosion group II, sub-group IIC, with the type of explosion protection explosion proof enclosure d, for temperature class T3
95

Privod en

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Privod en

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Privod en

Uploaded by

Copyright:

Available Formats

5, Moldavskaya str.

, Moscow, 121467, Russia

+7 (495) 411-7757, [email protected], www.oilgassystems.com

1. TURBOGENERATORS, SYNCHRONOUS, TWO POLE, AIR COOLED

2. Hydrogenerators 3. Small capacity generators

4. generator eXcitation control systems

5. Turbogenerator liFe support systems

6. TWO POLE SYNCHRONOUS MOTORS, HIGH-SPEED

7. Salient pole synchronous motors

8. EXCITATION SYSTEMS FOR SYNCHRONOUS MOTORS

5, Moldavskaya str., Moscow, 121467, Russia

+7 (495) 411-7757, [email protected], www.oilgassystems.com

9. Asynchronous eXplosion prooF motors with a short circuited rotor 

13. ELECTRICALLY DRIVEN GAS COMPRESSOR UNITS

14. TRANSFORMING EQUIPMENT

15. Traction electrical equipment

5, Moldavskaya str., Moscow, 121467, Russia

+7 (495) 411-7757, [email protected], www.oilgassystems.com

16. GOST CONVENTIONS

5, Moldavskaya str., Moscow, 121467, Russia

+7 (495) 411-7757, [email protected], www.oilgassystems.com

5, Moldavskaya str., Moscow, 121467, Russia

+7 (495) 411-7757, [email protected], www.oilgassystems.com

5, Moldavskaya str., Moscow, 121467, Russia

+7 (495) 411-7757, [email protected], www.oilgassystems.com

5, Moldavskaya str., Moscow, 121467, Russia

+7 (495) 411-7757, [email protected], www.oilgassystems.com

5, Moldavskaya str., Moscow, 121467, Russia

+7 (495) 411-7757, [email protected], www.oilgassystems.com

Phase connection pattern star star star star star star

Rotation speed, rpm 3000 3000 3000 3000 3000 3000

Efficiency, % 98.4 98.4 98.45 98.45 98.5 98.5

Weight, kg 121800 123000 158500 160500 207500 210000

Embodiment IM 7101 IM 7306 IM 7101 IM 7306 IM 7101 IM 7306

5, Moldavskaya str., Moscow, 121467, Russia

+7 (495) 411-7757, [email protected], www.oilgassystems.com

1.2. T (TS)-series turbogenerators with 2.563 MW capacities

Excitation system Location of HV leads of turbogenerators

Rated operating conditions

5, Moldavskaya str., Moscow, 121467, Russia

+7 (495) 411-7757, [email protected], www.oilgassystems.com

5, Moldavskaya str., Moscow, 121467, Russia

+7 (495) 411-7757, [email protected], www.oilgassystems.com

1.3. TK-series turbogenerators with 1.563 MW capacities

5, Moldavskaya str., Moscow, 121467, Russia

+7 (495) 411-7757, [email protected], www.oilgassystems.com

1.4. GTG-series turbogenerators with 2.58 MW capacities

Voltage, V 6300 10500 6300 10500 6300 10500 6300 10500

Efficiency, % 96.8 96.7 97.2 97.0 97.5 97.5 97.6 97.5

Weight, kg 13900 13900 15550 15550 20500 20500 27360 27360

* GTG-8-2R NF3 generator may be delivered with closed-loop ventilation GTG XX 2 R NF

5, Moldavskaya str., Moscow, 121467, Russia

+7 (495) 411-7757, [email protected], www.oilgassystems.com

1.5. Special-version turbogenerators

5, Moldavskaya str., Moscow, 121467, Russia

+7 (495) 411-7757, [email protected], www.oilgassystems.com

rotation speed, rpm capacity, MW T-turbogenerator TM marine turbogenerator

5, Moldavskaya str., Moscow, 121467, Russia

1. TURBOGENERATORS, SYNCHRONOUS, TWO POLE, AIR COOLED

2. Hydrogenerators 3. Small capacity generators

4. generator eXcitation control systems

5. Turbogenerator liFe support systems

6. TWO POLE SYNCHRONOUS MOTORS, HIGH-SPEED

7. Salient pole synchronous motors

8. EXCITATION SYSTEMS FOR SYNCHRONOUS MOTORS

9. Asynchronous eXplosion prooF motors with a short circuited rotor

13. ELECTRICALLY DRIVEN GAS COMPRESSOR UNITS

14. TRANSFORMING EQUIPMENT

15. Traction electrical equipment

16. GOST CONVENTIONS