PC357NJ0000F Series: Mini-Flat Package, General Purpose Photocoupler

Download as pdf or txt
Download as pdf or txt
You are on page 1of 14

PC357NJ0000F Series

PC357NJ0000F Series

Mini-flat Package, General Purpose Photocoupler

Description
PC357NJ0000F Series contains an IRED optically coupled to a phototransistor. It is packaged in a 4-pin Mini-flat package. Input-output isolation voltage(rms) is 3.75kV. Collector-emitter voltage is 80V and CTR is 50% to 600% at input current of 5mA.

Agency approvals/Compliance
1. Recognized by UL1577 (Double protection isolation), file No. E64380 (as model No. PC357) 2. Package resin : UL flammability grade (94V-0)

Applications
1. Hybrid substrates that require high density mounting 2. Programmable controllers

Features
1. 4-pin Mini-flat package 2. Double transfer mold package (Ideal for Flow Soldering) 3. High collector-emitter voltage (VCEO : 80V) 4. Current transfer ratio (CTR) : MIN. 50% at IF=5mA, VCE=5V 5. Several CTR ranks available 6. High isolation voltage between input and output (Viso(rms) : 3.75kV) 7. RoHS directive compliant

Notice The content of data sheet is subject to change without prior notice. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.

Sheet No.: D2-A00102FEN Date Jun. 30. 2005 SHARP Corporation

PC357NJ0000F Series Internal Connection Diagram


1 1 4 2 3 2 3 4

Anode Cathode Emitter Collector

Outline Dimensions
3.60.3 2.540.25
4 3

(Unit : mm)

SHARP mark "S"

Date code

Anode mark

357
1 2

4.40.2 Rank mark Factory identification mark 0.4


0.1

5.30.3 Epoxy resin 45 2.60.2 0.20.05

0.10.1

6
0.2 7.0+ 0.7

0.4 0.5+ 0.2

Product mass : approx. 0.1g Plating material : SnCu (Cu : TYP. 2%)

Sheet No.: D2-A00102FEN

PC357NJ0000F Series Date code (2 digit)


1st digit Year of production A.D Mark 2002 A 2003 B 2004 C 2005 D 2006 E 2007 F 2008 H 2009 J 2010 K 2011 L 2012 M N 2nd digit Month of production Month Mark January 1 February 2 March 3 April 4 May 5 June 6 July 7 August 8 September 9 October O November N December D

A.D. 1990 1991 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001

Mark P R S T U V W X A B C

repeats in a 20 year cycle

Factory identification mark


Factory identification Mark no mark Japan Indonesia China
* This factory marking is for identification purpose only. Please contact the local SHARP sales representative to see the actual status of the production

Country of origin

Rank mark
Refer to the Model Line-up table

Sheet No.: D2-A00102FEN

PC357NJ0000F Series
Absolute Maximum Ratings
Parameter Symbol IF Forward current *1 Peak forward current IFM Reverse voltage VR P Power dissipation Collector-emitter voltage VCEO Emitter-collector voltage VECO Collector current IC Collector power dissipation PC Total power dissipation Ptot Topr Operating temperature Storage temperature Tstg *2 Isolation voltage Viso (rms) *3 Soldering temperature Tsol Rating 50 1 6 70 80 6 50 150 170 30 to +100 40 to +125 3.75 260 (Ta=25C) Unit mA A V mW V V mA mW mW C C kV C

*1 Pulse width100s, Duty ratio : 0.001 *2 40 to 60%RH, AC for 1 minute, f=60Hz *3 For 10s

Electro-optical Characteristics
Symbol Parameter VF Forward voltage Reverse current IR Terminal capacitance Ct Collector dark current ICEO Collector-emitter breakdown voltage BVCEO Emitter-collector breakdown voltage BVECO Collector current IC Collector-emitter saturation voltage VCE (sat) Isolation resistance RISO Floating capacitance Cf Rise time tr Response time Fall time tf
Conditions IF=20mA VR=4V V=0, f=1kHz VCE=50V, IF=0 IC=0.1mA, IF=0 IE=10A, IF=0 IF=5mA, VCE=5V IF=20mA, IC=1mA DC500V, 40 to 60%RH V=0, f=1MHz

Output

Input

Input

Output

Transfer characteristics

VCE=2V, IC=2mA, RL=100

MIN. 80 6 2.5 51010

TYP. 1.2 30 5 0.1 11011 0.6 4 3

MAX. 1.4 10 250 100 30 0.2 1.0 18 18

(Ta=25C) Unit V A pF nA V V mA V pF s s

Sheet No.: D2-A00102FEN

PC357NJ0000F Series
Model Line-up
Taping IC [mA] Rank mark (IF=5mA, VCE=5V, Ta=25C) 750pcs/reel 3 000pcs/reel PC357NJ0000F PC357NTJ000F with or without 2.5 to 30.0 A PC357N1J000F PC357N1TJ00F 4.0 to 8.0 B PC357N2J000F PC357N2TJ00F 6.5 to 13.0 C PC357N3J000F PC357N3TJ00F 10.0 to 20.0 D PC357N4J000F PC357N4TJ00F 15.0 to 30.0 Model No. A or B PC357N5J000F PC357N5TJ00F 4.0 to 13.0 B or C PC357N6J000F PC357N6TJ00F 6.5 to 20.0 C or D PC357N7J000F PC357N7TJ00F 10.0 to 30.0 A, B or C PC357N8J000F PC357N8TJ00F 4.0 to 20.0 B, C or D PC357N9J000F PC357N9TJ00F 6.5 to 30.0 PC357N0J000F PC357N0TJ00F A, B, C or D 4.0 to 30.0 Package

Please contact a local SHARP sales representative to inquire about production status.

Sheet No.: D2-A00102FEN

PC357NJ0000F Series Fig.1 Forward Current vs. Ambient Temperature


70 60 Forward current IF (mA) 50 40 30 20 10 0 30

Fig.2 Diode Power Dissipation vs. Ambient Temperature


120 100 80 70 60 40

Diode power dissipation P (mW)

20 0 30

25 50 75 100 Ambient temperature Ta(C)

125

0 50 55 Ambient temperature Ta (C)

100

Fig.3 Collector Power Dissipation vs. Ambient Temperature


200 Collector power dissipation PC (mW)

Fig.4 Total Power Dissipation vs. Ambient Temperature


300

150

Total power dissipation Ptot (mW)


0 25 50 75 100 Ambient temperature Ta (C) 125

250

200 170 150

100

100 50

50

0 30

0 30

0 25 50 Ambient temperature Ta (C)

100

Fig.5 Peak Forward Current vs. Duty Ratio


10 000 Pulse width100s Ta=25C Peak forward current IFM (mA)

Fig.6 Forward Current vs. Forward Voltage


Ta=75C 50C 25C 0C 25C

1 000

Forward current IF (mA) 10 3 10 2 Duty ratio 10 1 1

100

100

10

10

0.5

1 1.5 2 2.5 Forward voltage VF (V)

3.5

Sheet No.: D2-A00102FEN

PC357NJ0000F Series Fig.7 Current Transfer Ratio vs. Forward Current


500 VCE=5V Ta=25C Current transfer ratio CTR (%) 400 Collector current IC (mA) 40 IF=30mA
20 mA

Fig.8 Collector Current vs. Collector-emitter Voltage


50 Ta=25C

300

30

PC(MAX.)
mA

10

200

20
5mA

100

10

0 0.1

1 10 Forward current IF (mA)

100

10

Collector-emitter voltage VCE (V)

Fig.9 Relative Current Transfer Ratio vs. Ambient Temperature


150 IF=5mA VCE=5V

Fig.10 Collector - emitter Saturation Voltage vs. Ambient Temperature


0.16 0.14 Collector-emitter saturation voltage VCE (sat) (V) 0.12 0.1 0.08 0.06 0.04 0.02 0 30 IF=20mA IC=1mA

Relative current transfer ratio(%)

100

50

0 30

80 60 40 0 20 Ambient temperature Ta (C)

100

0 20 80 60 40 Ambient temperature Ta (C)

100

Fig.11 Collector Dark Current vs. Ambient Temperature


105 VCE=50V 106 Collector dark current ICEO (A) 10
7

Fig.12 Response Time vs. Load Resistance


VCE=2V IC=2mA Ta=25C tr Response time (s) tf 10

100

108 109 1010 1011 30

td 1 ts

0 20 40 60 80 Ambient temperature Ta (C)

100

0.1 0.01

0.1 1 10 Load resistance RL (k)


Sheet No.: D2-A00102FEN

PC357NJ0000F Series Fig.13 Test Circuit for Response Time


VCC RL Collector-emitter saturation voltage VCE (sat) (V) Input Input RD Output Output 10% 90% VCE td tr Please refer to the conditions in Fig.12 ts tf

Fig.14 Collector-emitter Saturation Voltage vs. Forward Current


8 Ta=25C 7 6 5 4 3 2 1 0 0 3 12 6 9 Forward current IF (mA) 15 IC=0.5mA 1mA 3mA 5mA 7mA

Remarks : Please be aware that all data in the graph are just for reference and not for guarantee.

Sheet No.: D2-A00102FEN

PC357NJ0000F Series Design Considerations Design guide


While operating at IF<1.0mA, CTR variation may increase. Please make design considering this fact. This product is not designed against irradiation and incorporates non-coherent IRED.

Degradation
In general, the emission of the IRED used in photocouplers will degrade over time. In the case of long term operation, please take the general IRED degradation (50% degradation over 5 years) into the design consideration.

Recommended Foot Print (reference)


6.3

2.54

1.5

0.8

(Unit : mm)

For additional design assistance, please review our corresponding Optoelectronic Application Notes.
Sheet No.: D2-A00102FEN

PC357NJ0000F Series
Manufacturing Guidelines Soldering Method Reflow Soldering:
Reflow soldering should follow the temperature profile shown below. Soldering should not exceed the curve of temperature profile and time. Please don't solder more than twice.
(C) 300

Terminal : 260C peak ( package surface : 250C peak)

200

Reflow 220C or more, 60s or less 100 Preheat 150 to 180C, 120s or less

(min)

Flow Soldering :
Due to SHARP's double transfer mold construction submersion in flow solder bath is allowed under the below listed guidelines. Flow soldering should be completed below 260C and within 10s. Preheating is within the bounds of 100 to 150C and 30 to 80s. Please don't solder more than twice.

Hand soldering
Hand soldering should be completed within 3s when the point of solder iron is below 400C. Please don't solder more than twice.

Other notices
Please test the soldering method in actual condition and make sure the soldering works fine, since the impact on the junction between the device and PCB varies depending on the tooling and soldering conditions.

Sheet No.: D2-A00102FEN

10

PC357NJ0000F Series Cleaning instructions Solvent cleaning:


Solvent temperature should be 45C or below Immersion time should be 3 minutes or less

Ultrasonic cleaning:
The impact on the device varies depending on the size of the cleaning bath, ultrasonic output, cleaning time, size of PCB and mounting method of the device. Therefore, please make sure the device withstands the ultrasonic cleaning in actual conditions in advance of mass production.

Recommended solvent materials:


Ethyl alcohol, Methyl alcohol and Isopropyl alcohol In case the other type of solvent materials are intended to be used, please make sure they work fine in actual using conditions since some materials may erode the packaging resin.

Presence of ODC
This product shall not contain the following materials. And they are not used in the production process for this product. Regulation substances : CFCs, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methylchloroform) Specific brominated flame retardants such as the PBBOs and PBBs are not used in this product at all. This product shall not contain the following materials banned in the RoHS Directive (2002/95/EC). Lead, Mercury, Cadmium, Hexavalent chromium, Polybrominated biphenyls (PBB), Polybrominated diphenyl ethers (PBDE).

Sheet No.: D2-A00102FEN

11

PC357NJ0000F Series Package specification Tape and Reel package 1. 3 000pcs/reel Package materials
Carrier tape : A-PET (with anti-static material) Cover tape : PET (three layer system) Reel : PS

Carrier tape structure and Dimensions


F E D G I C J

B A H K
MAX .

Dimensions List A B 0.3 12.0 5.50.1 H I 0.1 7.4 0.30.05

C 1.750.1 J 3.10.1

D 8.00.1 K 4.00.1

E 2.00.1

F 4.00.1

Reel structure and Dimensions


e g c d

f a b

Dimensions List a b 370 13.51.5 e f 211.0 2.00.5

(Unit : mm) G +0.1 1.5 0

(Unit : mm) c d 801.0 130.5 g 2.00.5

Direction of product insertion

Pull-out direction

[Packing : 3 000pcs/reel]

Sheet No.: D2-A00102FEN

12

PC357NJ0000F Series 2. 750pcs/reel Package materials


Carrier tape : A-PET (with anti-static material) Cover tape : PET (three layer system) Reel : PS

Carrier tape structure and Dimensions


F E D G I C J

B A H
MAX .

Dimensions List A B 12.00.3 5.50.1 H I 0.1 7.4 0.30.05

C 1.750.1 J 3.10.1

D 8.00.1 K 4.00.1

E 2.00.1

(Unit : mm) F G +0.1 4.00.1 1.5 0

Reel structure and Dimensions


e g c d

f a b

Dimensions List a b 180 13.51.5 e f 1.0 21 2.00.5

(Unit : mm) c d 1.0 80 130.5 g 2.00.5

Direction of product insertion

Pull-out direction

[Packing : 750pcs/reel]

Sheet No.: D2-A00102FEN

13

PC357NJ0000F Series Important Notices


The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice. Observe the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) The devices in this publication are designed for use in general electronic equipment designs such as: --- Personal computers --- Office automation equipment --- Telecommunication equipment [terminal] --- Test and measurement equipment --- Industrial control --- Audio visual equipment --- Consumer electronics (ii) Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection with equipment that requires higher reliability such as: --- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- Traffic signals --- Gas leakage sensor breakers --- Alarm equipment --- Various safety devices, etc. (iii) SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- Space applications --- Telecommunication equipment [trunk lines] --- Nuclear power control equipment --- Medical and other life support equipment (e.g., scuba). If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Law of Japan, it is necessary to obtain approval to export such SHARP devices. This publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. Contact and consult with a SHARP representative if there are any questions about the contents of this publication.

[E182]

Sheet No.: D2-A00102FEN

14

You might also like