Bolted To The Wood. From Experience It Was Found, However,: DECEMBER 22, 1927

DECEMBER 22,
1927
feature of the unit hull and bodya sort of combination of flying-boat and tractor fuselagein which the functions of both are performed to the best possible advantage ; the composite hull constructiona wood frame with metal-covering sheets bolted thereto ; the practical and rugged amphibian gear- and the good flying qualities, which are described as giving the flying-boat the flying characteristics of the normal land 'plane. The Loening hull is undoubtedly the most interesting feature of the whole machine. The general arrangement of the hull may be followed by reference to the accompanying illustrations" from which it 'will be seen that a short central flying-boat type of flotation gear is employed, upon which is built up a "more-or-less orthodox type of fuselageboth neatly merging one into the other. This original design was evolved by Grover Loening in 1924, and has from the first given very satisfactory results. The Loening type of composite wood and metal construction was first used "in experimental flying-boats designed by Loening in 1911 and 1912, and again in 1914 on the seaplanes built by the Dayton Wright Co. In this type of construction the framework is wood, fastened together with metal gusset plates the entire framing then being covered by sheet metal bolted to the wood. From experience it was found, however, that great care had to be taken to separate the duralumin sheet and the wood by a layer of fabric impregnated with bitumastic or marine glue.
S
members are all joined by simple, fiat gusset plates of dural, bolted throughout with duralumin bolts, giving an excellent job for production. The lower part of the hull frame, and the upper longerons and diagonals framing the main fuselage section, are all built as one unit, the lower part, however, having a curved " tumble-home " side, and the upper body section a flat side with a rounded top. The bottom is specially reinforced to withstand contact with the deck-alighting gear on aircraft carriers, and in addition, the hull is specially braced internally and externally to withstand the catapult stress incident to being shot from the U.S. Navy's powder catapult. The pilot's seat is located well forward, between the wings, where good visibility is provided, especially for deck landings. Immediately behind is the gunner's cockpit, while below, in the deep hull, there is a cabin for the observer or wireless operator, who has a good range of vision below the wings through windows in the sides of the hull. As regards the wing construction on the OL-8, this is also composite in that the ribs are all made of dural and the spars of spruce. This gives an excellent combination for a seaplane (particularly with the advent of the new non-corrosive duralumin called '" Alclad," which is used on the ribs) because the maintenance difficulties of the small parts on a seaplane of glued-up wooden ribs coming apart are entirely solvedand yet the reliability and lightness of wooden ribs are maintained throughout.
A close-up of the 424h.p. Pratt and Whitney "Wasp"

Si
air-cooled radial engine in the installed Loening
OL-8 Amphibian.
The use of bolts instead of rivets or wood screw? is the result of a very careful study, and is particularly desirable in that it makes the protection of the bolt against corrosion in salt water much easier, because each individual bolt can receive numerous coatings of enamel or bitumastic. Furthermore, in being fastened to the hull, it is not hammered like a rivet, and therefore is not likely to lose its heat-treatment against corrosion. It is claimed, therefore, that any amount of protection can be given the bolts, which is not the case with rivets. The wood frame has enough resiliency to take up the severe local strains of the land operation of this machine to prevent leaks from developingwhich has always been a serious cause of trouble in amphibians. One other advantage of this form of construction is the sealing of the joints by means of fabric tape impregnated with a special water-proof glue which, clamped botween the metal covering and the wooden frame with duralumin bolts, gives a remarkably watertight resultparticularly as the wood, when damp, swells sufficiently to give all the advantages of tightening found in wooden hull construction. In the OL-8 hull, the frame consists essentially of two longitudinal girders of the Pratt truss type, cross connected by bulkheads, subdividing the hull into numerous watertight compartments. The spruce longerons of this framework and the diagonal
The interpiane struts consist of welded steel " N " struts with the usual streamline wires bracing the two-bay wing, all being held by simple flat-plate metal fittings which project through the wing, but which are carefully boxed in so that no salt water can enter the wing around the fittings. Both top and bottom 'planes have a dihedral angle of 3 degs. and a stagger of 12 in., but there is no sweep-back. Ailerons, of high aspect ratio, are fitted to top and bottom 'planes, the lower ailerons being operated by cables in the bottom wings, and the upper ailerons being actuated by struts from the lower ones. The Loening 10A wing section is employed on the OL-8, a section, the details of which have never been published, developed by the Loening engineers, that has given exceptional results'. It may be of interest to note, in passing, that this is the same section which, applied to D.H.4-type machines, with no other change, increased their speed over the R.A.F. 15 section by over 13 m.p.h., decreased the landing speed 11 m.p.h., and increased the ceiling 2,000 ft. Several D.H's. are now in service of the U.S. Government, using Loening 10A wingsthe most notable being a special D.H. used by Major E. H. Brainard, Chief of the U.S. Marine Corps Aviation Service. The wings have a high safety factor, and all forms of " stunting" can safely be carried out on the Loening
862

Bolted To The Wood. From Experience It Was Found, However,: DECEMBER 22, 1927

Uploaded by

Copyright:

Available Formats

Bolted To The Wood. From Experience It Was Found, However,: DECEMBER 22, 1927

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Bolted To The Wood. From Experience It Was Found, However,: DECEMBER 22, 1927

Uploaded by

Copyright:

Available Formats

DECEMBER 22,

A close-up of the 424h.p. Pratt and Whitney "Wasp"

air-cooled radial engine in the installed Loening

You might also like