Self Study Programme 490

Audi 6.3l W12 FSI engine

Audi Service Training

A twelve cylinder is the pinnacle of engine design, and traditionally a hallmark of luxury class cars in particular. The rst-generation A8 was available with an engine of this type from 2001 onwards, and a more advanced version could be obtained from 2004 onwards in the following model series. Audi's engineers have now thoroughly revised the W12, increasing its displacement to 6.3 litres and equipping it with petrol direct injection for higher power and eciency. The 6.3l W12 FSI engine gives the long-wheelbase Audi A810 sportscar-like performance: it sprints from zero to 100 kph in just 4.9 seconds; the electronically governed top speed of 250 kph is a mere formality.

The engine runs exceptionally smoothly, and only at high engine loads and speeds do the car's occupants sense any of this supreme power at work. For use in the long-wheelbase A810, Audi's engineers have converted the W12 engine to FSI petrol direct injection. This involved extensive modication of the cylinder heads. The high fuel economy of the 6.3l W12 FSI engine compared with its competitors is mainly a result of technologies from Audi's modular eciency platform which is used throughout the A8 model line.

490_002

Learning objectives of this Self Study Programme: In this Self Study Programme you will learn about the technology of the 6.3l W12 FSI engine. When you have worked your way through this Self Study Programme, you will be able to answer the following questions:

Which adaptations have been made for the use of petrol direct injection? How does the crankcase breather work? How is the oil circuit designed? What are the special features of the fuel system? What modications have been made to the engine management system? What are the points to note when servicing the vehicle?

Contents
Introduction
Brief technical description _________________________________________________________________________________________________________________________________ 4 Specications ________________________________________________________________________________________________________________________________________________ 5

Engine mechanicals
Cylinder block _______________________________________________________________________________________________________________________________________________ 6 Crank mechanism ___________________________________________________________________________________________________________________________________________ 7 Pistons and conrods ________________________________________________________________________________________________________________________________________ 8 Chain drive ___________________________________________________________________________________________________________________________________________________ 9 Crankcase breather ________________________________________________________________________________________________________________________________________ 10 Cylinder head _______________________________________________________________________________________________________________________________________________ 12 Belt drive ____________________________________________________________________________________________________________________________________________________ 13

Oil supply
Overview ____________________________________________________________________________________________________________________________________________________ 14 Oil circuit ____________________________________________________________________________________________________________________________________________________ 16 Oil pump ____________________________________________________________________________________________________________________________________________________ 17

Air supply
Intake airow system _____________________________________________________________________________________________________________________________________ 18 Secondary air system ______________________________________________________________________________________________________________________________________ 20 Vacuum supply _____________________________________________________________________________________________________________________________________________ 22

Cooling system
Overview ____________________________________________________________________________________________________________________________________________________ 24 Coolant thermostat ________________________________________________________________________________________________________________________________________ 25

Fuel system
System overview ___________________________________________________________________________________________________________________________________________ 26 Fuel rails ____________________________________________________________________________________________________________________________________________________ 28 Additional volume on the fuel rails _______________________________________________________________________________________________________________________ 29 High-pressure injectors ____________________________________________________________________________________________________________________________________ 30

Engine management
System overview ___________________________________________________________________________________________________________________________________________ 32 Engine control unit J623 and engine control unit 2 J624 ______________________________________________________________________________________________ 34

Exhaust system
Overview ____________________________________________________________________________________________________________________________________________________ 38 Exhaust aps _______________________________________________________________________________________________________________________________________________ 39

Service
Special tools ________________________________________________________________________________________________________________________________________________ 40 Maintenance operations ___________________________________________________________________________________________________________________________________ 41

Annex
Glossary _____________________________________________________________________________________________________________________________________________________ 42 Self Study Programmes ___________________________________________________________________________________________________________________________________ 43

The Self Study Programme teaches a basic knowledge of the design and functions of new models, new automotive components or new technologies. It is not a Repair Manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. For maintenance and repair work, always refer to the current technical literature. Terms written in italics or indicated by an asterisk are explained in the glossary at the back of this Self Study Programme.

Note

Reference

Introduction
Brief technical description
Twelve-cylinder petrol engine with four rows of three cylinders arranged in a W conguration More compact dimensions than a comparable V8 engine Length / width / height: approx. 50cm / 70cm / 70cm Two cylinder heads with four valves per cylinder and two camshafts per bank including hydraulic camshaft adjusters The engine is controlled by a multi-element chain drive (optimised for low friction) FSI petrol direct injection with twin high-pressure fuel pumps, twin fuel rails and six-port high-pressure injectors Recuperation system* for energy recovery during deceleration phases

490_004

Reference For further information about the basic design of the W12 engine, refer to Self Study Programmes 267 "The Audi 6.0l W12 engine in the Audi A8 Part 1" and 268 "The Audi 6.0l W12 engine in the Audi A8 Part 2".

Specications

Torque/power curves

6.3l W12 FSI engine Power in kW Torque in Nm

Engine speed [rpm]

490_001

Engine code Type Displacement in cm Stroke in mm Bore in mm Number of valves per cylinder Firing order Compression ratio Power output in kW at rpm Torque in Nm at rpm Fuel Mixture formation Engine weight in kg Engine management Emissions standard CO2 emission in g/km Exhaust gas aftertreatment Vehicle use
3

CEJA Twelve-cylinder W type engine with a V angle of 15 and a bank angle of 72 6299 90,4 86,0 4 1-7-5-11-3-9-6-12-2-8-4-10 11,8:1 368 at 6200 625 at 4750 Sulphur free premium unleaded to DIN EN 228 / 95 RON1) FSI direct injection, with 130 bar max. system pressure and six-port injectors 247 Bosch MED 17.1.6 EU5 / ULEV II 290 Four air-gap insulated manifold CAT modules, each with a close-coupled ceramic catalytic converter and twin oxygen sensors A8 L

1)

Unleaded regular 91 RON petrol can also be used, with slight loss of power.

Engine mechanicals
Cylinder block
Compared with the 6.0l W12 engine, the engineers have enlarged the cylinder bore from 84 to 86 millimetres. The cylinder block is cast from a lightweight, high-strength aluminum-silicon alloy. The bottom section comprises a cast iron crossmember with embedded main bearing pedestals.

Cylinder block

Engine number of left-hand side of cylinder block

Integrally cast main bearing pedestals for crankcase bearings

Bearing cross-member

Oil pan top section

Oil pan with bae plates

490_005 6

Crank mechanism
The forged crankshaft has a 12-degree angle of crankpin oset, so that the air-fuel mixture in all 12 cylinders is ignited at the ideal interval of 60 degrees.

Cylinder bank 1

Cylinder bank 2

Gearing for the separate oil pump chain drive

Direction of travel

Split-pin conrod bearing journal

Oil supply port for the conrod bearings

Transverse bore in the crankshaft Conrod bottom section

Conrod bearing

490_006 7

Pistons and conrods

The pistons are forged from a high-strength light alloy and have angled crowns to compensate for the cylinder bank angle. The shape of the piston crowns has been adapted for the use of FSI petrol direct injection. The design of the W12 engine necessitated the use of dierent high-pressure injectors with dierent placement angles in the cylinder head (see "Fuel system" on page 26). For this reason, the "outer" cylinders (1, 3, 5, 8, 10 and 12) have dierent pistons to the "inner" cylinders (2, 4, 6, 7, 9 and 11).
Forged piston

Rectangular ring

Minute ring Oil scraper ring

490_019

Design
Pistons of cylinders 2, 4, 6, 7, 9 and 11 Pistons of cylinders 1, 3, 5, 8, 10 and 12

490_007

490_008

Conrods
Extra-narrow trapezoidal conrods are used.

490_009 8

Chain drive
The timing gear is located on the gearbox side of the engine. It is subdivided into primary and secondary drives. All components of the chain drive are designed to last the lifetime of the engine (300,000km). No provision has been made for adjustment by service personnel

Primary drive
The primary drive is driven by a sprocket on the crankshaft. A simplex roller chain drives an intermediate gear. The intermediate gear provides speed reduction and drives the secondary drives. The chain is guided by means of a sliding rail. Chain tensioning is provided by a spring-loaded chain tensioner, which is assisted and damped by engine oil from the oil circuit.

Secondary drives
The two secondary drives are driven by the intermediate gear. The two camshafts are driven by a single chain per cylinder bank. Bush chains are used. In this case too, the chains are guided by sliding rails. The chain tensioners work on the same principle as in the primary drive. In this case, however, the tensioning force of the chain tensioner does not act on the tensioning rail, rather on a rotatably mounted tensioning lever. At the end of the tensioning lever, a sprocket running on ball bearings engages the secondary chain. The chains of the secondary drives have to be removed in order to take o the cylinder heads.

Cylinder bank 2

Cylinder bank 1

Chain tensioner of cylinder bank 2

Sliding rail

Tensioning lever of cylinder bank 2

Tensioning gear of cylinder bank 1

Intermediate shaft gear Direction of travel Chain tensioner

Sliding rail

Sliding rail

Crankshaft sprocket (primary drive)

490_010

Crankcase breather
Blow-by gases* are introduced directly into the cylinder heads. For this purpose, vent lines are connected directly to the cylinder head covers on the belt side of the engine. The blow-by gases ow through these vent lines into the oil separator module of the crankcase breather which is located at the top end of the engine between the two intake modules. The port with cover for lling the engine oil is located on the oil separator module. The lled engine oil ows through the vent lines into the engine. The blow-by gases are channelled through the coarse oil separator in the oil separator module. The coarse oil separator comprises multiple labyrinth-like channels with collecting walls which retain most of the oil droplets due to their inertia. The separated engine oil drips from the walls and is collected in a pan in the oil separator module. From here, the oil runs along a return line and drains into the timing case at the back of the engine. The pre-treated blow-by gases then ow through a ne oil separator, continuing through the pressure control valve. The blow-by gases are introduced directly into the intake manifold of cylinder bank 1 through a plastic pipe connected to the intake manifold of cylinder bank 1. If the vacuum inside the intake manifold is too high, the pressure control valve in the oil separator module closes. This prevents an excessively high vacuum from building up inside the crankcase and damaging the crankshaft oil seals.

Design and operation

Blow-by-gas inlet (raw gas) from the cylinder head cover (cylinder bank 1) Inow of treated blow-by gases into the intake manifold Fine oil separator (impactor) Oil return line in the timing case

Coarse oil separator

Heating resistor (crankcase breather) N79

Pressure control valve in the oil separator module

Collecting walls for liquid blow-by gas constituents

Blow-by-gas inlet (raw gas) from the cylinder head cover (cylinder bank 2)

Labyrinth-like channels in the coarse oil separator

Separated engine oil collects in the drip pan

490_027

10

Fine oil separation

After the blow-by gases have passed the coarse oil separator, they ow through a ne oil separator. In terms of its working principle, the ne oil separator is a socalled impactor*.

Functional principle The functional principle is the same as that of an inertial separator. The blow-by gas ow is deected "sharply", which means that the oil droplets cannot follow the air ow due to their higher mass inertia. They collide with the housing wall and, as a result, are separated. This eect is intensied in the impactor, where the mass ow is directed through nozzles. The ow is accelerated inside the nozzle and deected 90 straight after leaving the nozzle. Even very small oil droplets (<1m) have little chance of following the air ow and collide with the wall. A valve opens a gap acting as a bypass to the nozzles at high blow-by gas ow rates. This allows the nozzles to be designed for lower volumetric ow rates, which in turn results in higher separation eciency. The opening gap on the overow valve acts like a nozzle, speeding up the gas ow. Thus, a constantly high level of separation eciency is maintained even when the overow valve is open.

Low blow-by gas ow rate

Blow-by gases from the coarse oil separator

High blow-by gas ow rate

Treated blow-by gases to intake manifold

490_036

490_037

Nozzle

Overow valve

Oil drip pan with outlet

Oil return to timing case

Oil return line Sealing surface facing cylinder head 2

No internal crankcase pressure must ever be allowed into the oil separator module via the oil return line. This is prevented by a syphon downstream of the port in the timing case cover. In this way, the oil return inlet is always below the oil level in the oil collection chamber, with the result that no exchange of gases can take place.

490_038

Heating
To prevent the crankcase breather from freezing up in cold weather conditions, an electrical heater at the inlet to the intake manifold is activated. To this end, the engine control unit 2 J624 activates the heating resistor (crankcase breather) N79 at ambient temperatures below 0C. The heating resistor is deactivated when an

Oil collection chamber

Timing case cover

ambient temperature of 3C is exceeded. The engine control unit receives the ambient temperature signal from the control unit in the dash panel insert J285.

11

Cylinder head
Overview (using cylinder bank 1 as an example)
1 2 4 5 7

10 12 11

13 14 15 16 17 18 19 22 21

20

23

24

26

27

25
12

490_012

Legend of gure on page 12: 1 2 3 4 5 6 7 High-pressure fuel pump Fuel metering valve N290 Roller tappet Low-pressure connection (supply) High-pressure connection Cylinder head cover Cylinder ange screws (steel screws / aluminium screws for the cover) Crankcase breather connecting port 23 9 10 11 12 13 14 Camshaft bearing cover 24 Drive cam for high-pressure fuel pump 25 Exhaust camshaft 26 Intake camshaft 27 Roller cam follower (exhaust) Support element (exhaust) Anti-freeze plug Oil pressure switch F1 Suspension eye Secondary air inlet Anti-freeze plug 15 16 17 18 19 20 21 22 8 Valve spring plate (exhaust) Valve cotters (exhaust) Valve stem seal (exhaust) Valve spring (exhaust) Exhaust valve (long) Exhaust valve assembly (short) Intake valve assembly (short) Intake valve assembly (long)

Belt drive
The auxiliary units are driven by one-piece belt drive on the front end of the 6.3l W12 FSI engine. Key dierences compared to the 6.0l W12 engine are, in particular, the belt routing and the way the alternator and AC compressor are connected directly to the cylinder block by a threaded tting. Depending on whether servotronic or dynamic steering is tted, dierent belt drives with dierent ratios are used for the power steering pump.

Coolant pump Belt tensioner

Tensioner pulley Deection pulley

Alternator

Deection pulley

Crankshaft vibration damper

AC compressor

Power steering pump

490_011 13

Oil supply
Overview
The 6.3l W12 FSI engine employs a lubrication system with conventional oil intake from an oil pan. As is the case with the 6.0l W12 engine on the AudiA801, dry sump lubrication* has been dispensed with. An aluminium oil pan is located on the underside of the engine. To ensure a reliable supply of oil even during high transverse and longitudinal acceleration, bae plates have been tted at the oil pan intake (see gure in page 16). By eliminating dry-sump lubrication, it was possible to design the overall oil circulation system more simply. It was also possible to employ a single-stage oil pump (see page 17).
Intake camshaft timing adjustment valve 1 N205

Exhaust camshaft timing adjustment valve 1 N318

Cylinder bank 1

Oil ports for supplying the camshafts and the support elements on the roller cam followers

Main oil port

Oil pressure switch F22 (switching pressure 3.84.6bar)

Oil cooler (coolant-oil)

Oil port in oil pan top section (oil pump oil cooler)

Oil port in the oil pan top section (oil cooler oil lter)

Oil pump with oil intake into the oil pan

14

Intake camshaft timing adjustment valve 2 N208

Exhaust camshaft timing adjustment valve 2 N319

Cylinder bank 2

Timing case for camshaft adjustment

Oil port to chain tensioner

Oil ports for supplying the main bearings

Oil spray jets for piston cooling

Oil pressure switch for reduced oil pressure F378 (switching pressure 1.2 1.6bar)

Oil lter module on oil pan top section

490_021 15

Oil circuit
The oil pressure (raw oil) produced by the oil pump initially passes through the oil cooler and then through the oil lter module. An oil cooler bypass valve ensures a reliable ow of oil in the event that the oil cooler becomes clogged. The oil (raw oil) ows from the oil cooler through ports in the oil pan top section on to the oil lter. The clean oil then ows through corresponding oil ports in the cylinder block and the cylinder heads to the lubrication points (loads).

Oil ow in the lower section of the engine

Oil cooler bypass valve (short-circuit valve)

Oil ow to the loads

Coolant feed Coolant return line

Cylinder block

Oil cooler Oil pan top section with oil port (oil cooler oil lter)

Fixed-displacement oil pump

Pilot line

Oil lter module

Oil pan top section

Bae plates

Oil level and oil temperature sensor G266

490_013 16

Oil pump
The oil pump is a gear pump congured for xed displacement. Since the 6.3l W12 FSI engine does not, like the previous engine on the A801, have dry-sump lubrication, the oil pump draws the oil directly from the oil pan. The oil pump is driven by a separate chain drive which connects directly to crankshaft. This chain drive is located on the opposite side of the timing gear on the engine and has a chain tensioner. The chosen gear ratio is such that the pump rotates more slowly than the crankshaft (i = 0.633). It is envisaged that the xed-displacement oil pump will be replaced by a volume-controlled oil pump at a future date.

Pressure control
A control piston inside the oil pump controls oil pressure and diverts any surplus oil. Oil pressure is present in a pilot line running from the oil port in the oil pan top section to the control piston in the oil pump. The control piston inside the oil pump diverts surplus oil to the suction side. During pump operation, the oil pressure is kept constant at approx. 5 bar at any engine speed (upwards of elevated idle speed). A pressure relief valve (cold start valve) opens to protect the engine at approx 10 bar. This can occur at very low engine oil temperatures, for instance.

Chain tensioner
490_014

Design
Pumphead Pump gear Oil pump housing Drive shaft gear

Driven pump gear

Cold start valve

Control piston
490_029

Reference For further information about the design and function of the xed-displacement oil pump, refer to Self-Study Programme 451 "Audi 2.5l TFSI Engine".
17

Air supply
Intake airow system
Cylinder bank 1
Suction jet pump to assist vacuum supply (on cylinder bank 1 only)

Throttle valve control unit 1 J338 with throttle valve drive 1 angle senders 1+2 G187, G188 Throttle valve drive G186

Air lter housing of cylinder bank 1

Intake manifold pressure sender G70 with intake air temperature sender G42

Air intake from the front end

Compared to the intake system of the 6.0l W12 engine, the system on the 6.3l W12 FSI engine has undergone several major modications. For example, the entire secondary air system is located at the back of the engine directly on the gearbox (see page 20).

A suction jet pump located on the throttle valve control unit of cylinder bank 1 is used to produce the vacuum required for braking and actuating the exhaust aps (see page 23). The air ducting system has also been modied compared to the 6.0l W12 engine. The air for the right-hand cylinder bank is taken in by the right-hand air duct and the air for the left-hand cylinder bank by the left-hand air duct.

18

Cylinder bank 2

Inlet for blow-by gases from the crankcase breather

Intake manifold 1

Intake manifold 2

Throttle valve control unit 2 J544 with throttle valve drive 2 angle senders 1+2 G297, G298 Throttle valve drive 2 G296

Air mass meter 2 G246 with intake air temperature sender 2G299

Air lter housing of cylinder bank 2

Rubber buer to support the air lter element

490_033

19

Secondary air system

The secondary air system ensures that the catalytic converters heat up more quickly and are available sooner after a cold start. Unlike the 6.0l W12 engine, the secondary air pumps are no longer connected to the air lter housings. For reasons of space, the secondary air pumps, as is the entire secondary air system, are installed at the back of the engine on the gearbox. The secondary air system therefore also has a separate air lter.

Overview
Combination valve 1 Combination valve 2

Secondary air pressure sender 2 G610

Secondary air pump motor 2 V189

Secondary air pump motor V101

Air lter for the secondary air system Secondary air pressure sender G609
490_034

Inlet on cylinder head 2 for introducing secondary air into the exhaust ow

20

Function
Air is drawn in by the two secondary air pumps (secondary air pump motors 1 and 2 V101 or V189) via the air lter of the secondary air system. For this purpose, both of the secondary air pumps are activated by engine control units 1 and 2 via secondary air pump relays J299 and J545. The air ows through combination valves 1 and 2 (self-opening) to both cylinder heads, where it is mixed with the exhaust gas ow. The secondary air pumps distribute air in a crossover fashion, i.e. secondary air pump 2 is connected to combination valve 1 and secondary air pump 1 is connected to combination valve 2.

Air lter of the secondary air system

Both secondary air pumps drawn in air through a common air lter. No replacement interval is specied for the air lter element.

Air ow to the secondary air pumps

Air lter housing retaining plate

Air lter element

Air lter housing cover

490_035

21

Vacuum supply

490_031

22

Suction jet pump

The conventional method of supplying vacuum to the brake servo and the engine components is problematic in the case of petrol engines, particulary in combination with automatic transmission. This means that installing a vacuum line after the throttle valve would not be sucient to produce the vacuum required by the various subsystems because, in many engine operating conditions, the wide open throttle valve would result in low mass ow rates and, consequently, insucient vacuum in the intake manifold. In the 6.3l W12 FSI engine, therefore, the requisite vacuum is produced by a suction jet pump. The suction jet pump is connected in parallel with the throttle valve contol unit J338 before and after the throttle valve (right-hand cylinder bank). The diverted air ow passes through the suction jet pump, thereby producing a vacuum (Venturi principle).
Vacuum line to brake servo Suction jet pump

490_032

Throttle valve control unit J338 on the right-hand cylinder bank

Brake vacuum pumpV192

If required, an electrical vacuum pump (brake vacuum pump V192) is activated to assist with vacuum delivery. One such application is cold starting For example, when the catalytic converter is heating up, the throttle valve is wide open. In this case, the vacuum produced by the suction jet pump is not enough to suciently evacuate the brake servo. The brake servo pressure sensor G294 is connected to the line to the brake servo and sends its readings to the engine control unit J623. The brake vacuum pump V192 is activated (in a map-controlled manner) by the engine control unit until the requisite vacuum is present.

Legend of gure on page 22: A B C D E F G H I J K Brake vacuum pumpV192 Brake servo Brake servo pressure sensorG294 Left secondary air combination valve Secondary air pressure sender 1 G609 Secondary air pump motor V101 Right secondary air combination valve Secondary air pressure sender 2 G610 Secondary air pump motor 2 V189 Air lter of the secondary air system Nonreturn valve
23

L M N O P Q R S T U

T-piece with ow restrictor Activated charcoal canister solenoid valve 1 N80 Activated charcoal canister Vacuum reservoir Exhaust ap valve 2 N322 Left exhaust ap Vacuum reservoir Exhaust ap valve 1 N321 Right exhaust ap Suction jet pump

Cooling system
Overview
(vehicle with auxiliary heater)

Cooled coolant Hot coolant

490_028

Legend: A Auxiliary heater (optional equipment) B C D E F G H I J Recirculation pump V55 Coolant circulation pump V50

K L

Coolant thermostat (initial opening temperature: 97C) Coolant circuit thermostat for ATF cooling (initial opening temperature: 75C) ATF cooler Coolant expansion reservoir Coolant thermostat for right-hand additional radiator (hot climate version 8Z6, 8Z9 or higher) Right-hand additional radiator (hot climate version 8Z6, 8Z9 or higher) Coolant radiator Left-hand additional radiator Coolant run-on pump V51

M Heater coolant shut-o valve N279 N Front heater heat exchanger O Rear heater heat exchanger Engine oil cooler Alternator Q Coolant pump R Coolant temperature sender G62 S
24

Coolant thermostat
The coolant thermostat is located at the front end of the engine. The coolant ows to both cylinder heads converge inside the coolant thermostat housing. The coolant thermostat for the primary cooling circuit opens at a temperature of 97C. The plunger of the expansion element rests on the housing cover. The sliding ring moves with the expansion element and, depending on its position, disconnects the secondary cooling circuit from the primary cooling circuit. The coolant thermostat housing has three location bolts into which the engine cover clips.

Design
Connection to cylinder head 1 Connection to vent line Location bolt

Connection to cylinder head 2

Connection from radiator

Connection from ATF cooler

Sliding ring

Connection from alternator and oil cooler

Housing

Expansion element

Compression spring

Connection to radiator

Housing cover

490_025

Note The cooling system may only be relled using cooling system charge unit VAS 6096. Otherwise, malfunctioning of the automatic gearbox may occur. Refer to the Workshop Manual.

25

Fuel system
System overview
As in previous FSI engines, the fuel system is divided into a low pressure and high-pressure fuel systems. Both systems operate in a demand responsive fashion, and neither system has a return line.

Low pressure system

The low pressure system is a closed-loop system in which the system pressure is monitored by the low-pressure fuel pressure sensor G410. Depending on requirements, the pressure is set to between 3.5 and 6 bar. High fuel pressure Low fuel pressure

Fuel distributor 1 (rail) High-pressure pump 1 Fuel pressure sensor G247 High pressure accumulator 1 (rail) Fuel metering valve N290 Injector, cylinder 6 N84 Direction of travel

Injector, cylinder 5 N83

Injector, cylinder 4 N33

Injector, cylinder 3 N32

Injector, cylinder 2 N31

Injector, cylinder 1 N30

26

Engine control unit J623

Battery (positive)

Ground

Bae housing Fuel pump control unit J538 Fuel pump (pre-supply pump) G6

Low-pressure fuel pressure sender G410

Fuel distributor 2 (rail) High-pressure pump 2 Fuel pressure sensor 2 G624 High pressure accumulator 2 (rail)

Fuel metering valve 2 N402

Injector, cylinder 12 N302 Injector, cylinder 11 N301

Injector, cylinder 10 N300

Injector, cylinder 9 N299

Injector, cylinder 8 N86

Injector, cylinder 7 N85

490_023

27

Fuel rails
High pressure system
Due to the engine's design, the high fuel pressure is distributed to the high pressure injectors through twin fuel rails. A single high-pressure fuel pump is responsible for supplying each cylinder bank. The electrical control unit is congured in such a way that the engine control unit J623 (master) controls cylinder bank 1 and engine control unit 2 J624 (slave). The low-pressure fuel pressure sender G410 is read in by the engine control unit J623. Both high pressure sides are therefore hydraulically independent of each other. For this reason, a separate fuel pressure sender is required for each cylinder bank. The high-pressure pumps are integrated in the cylinder head covers and driven by a three-lobe cam on the exhaust camshafts. They operate at pressures of between 40and 120bar. Hitachi pumps are tted.

Feed line from fuel tank

Fuel pressure sender G247

High-pressure fuel pump 2

High-pressure fuel pump 1

Fuel pressure sensor 2 G624 Low-pressure fuel pressure sender G410

Fuel distributor 2 (rail)

Long injectors for "outer" cylinders

Fuel distributor 1 (rail)

Short injectors for "inner" cylinders

490_016

Reference For further information about the function and control concept of the high-pressure fuel pumps, refer to Self-Study Programme 432 "Audi 1.4l TFSI Engine".
28

Additional volume on the fuel rails

Both fuel rails have additional volume in the form a tube. This additional volume is required to compensate for pressure peaks and pressure uctuation. The greater the volume, the lesser the eect of the pressure drop due to loss of volume during injection. The diameters of the rails could theoretically have easily been made slightly larger. However, this was not possible due to the constraints on installation space. The additional volume solution was chosen for this reason.

Fuel rail on cylinder bank 2

Feed line from high-pressure fuel pump Fuel distributor 2 (rail) Fuel pressure sensor 2 G624

Connecting duct (3x)

High pressure accumulator 2 (rail)

490_022

Note Caution: injury hazard Very high pressures may exist inside the fuel system. To open the high-pressure side, please follow the directions given in the Workshop Manual.

29

High-pressure injectors
The fuel is injected into the combustion chambers at a pressure of up to 120 bar. This task is performed by high-pressure injectors, of which there are two types on the 6.3l W12 FSI engine. The six individual jets of each high-pressure injector are arranged in such a way as to provide an optimal spatial alignment. Dierent pistons with correspondingly shaped crowns are used on account of the dierent installation angles of the injectors (see page 8).

Cylinders 1, 3, 5, 8, 10, 12 long high-pressure injectors

In the case of "outer" cylinders 1, 3, 5, 8, 10 and 12, longer injectors are used to deliver the fuel from each of the fuel rails between the cylinder heads to the cylinders.

Intake camshaft

Intake port

Long high-pressure injector

Piston with adapted crown

Outer cylinder

490_017

30

Cylinders 2, 4, 6, 7, 9, 11 short high-pressure injectors

The high-pressure injectors of "inner" cylinders 2, 4, 6, 7, 9 and 11 are very similar in design to those of other Audi FSI and TFSI* engines.

Intake camshaft

Intake port

Short high-pressure injector

Piston with adapted crown

Inner cylinder

490_018

31

Engine management
System overview
Low-pressure fuel pressure sender G410

Coolant temperature sender G62 Secondary air pressure sender 1 G609 Air mass meter G70 Intake air temperature sender G42 Accelerator pedal position sensor G79 Accelerator pedal position sensor 2 G185 Engine speed sender G28

Knock sensors 1+2 G61, G66 Fuel pressure sender G247 Hall sender G40 Hall sender 3 G300

Engine control unit J623 (master)

Throttle valve control unit J338 Throttle valve drive angle senders 1+2 for electronic power control G187, G188 Oil pressure switch for reduced oil pressure F378 Powertrain CAN databus

Oil level/oil temperature sensor G266

Brake light switch F

Oxygen sensors 1+2 G39, G108 Oxygen sensors 1+2 after catalytic converter G130, G131 Auxiliary signals: Cruise control on/o switch E45 Convenience sys. central control unit (wake-up door contact) J393 Vacuum sensor in brake servo G483

Fuel pressure sensor 2 G624 Hall sender 2 G163 Hall sender 4 G301 Throttle valve control unit 2 J544 Throttle valve drive 2 angle sensors 1+2 G297, G298 Knock sensors 3+4 G198, G199 Oxygen sensor 3+4 G285, G286 Oxygen sensors 3+4 after catalytic converter G287, G288 Secondary air pressure sender 2 G610 Fuel tank pressure sensor G4001) Air mass meter 2 G246 Intake air temperature sender 2 G299 Oil pressure switch F22 Auxiliary signals: Automatic gearbox control unit (selector lever position P/N) J217 Engine control unit 2 J624 (slave)

1)

American markets only

32

Private CAN

Starter motor relay J53 Starter motor relay 2 J695 Brake servo relay J569 Brake vacuum pumpV192 Exhaust ap valve 1 N321 Fuel pump relay J17 Fuel pump control unit J538 Fuel predelivery pump G6 Terminal 15 voltage supply relay J329 Ignition coils with power output stages 1 6 N70, N127, N291, N292, N323, N324 Fuel metering valve N290 Electro/hydraulic engine mounting sol. valve, right N145

Power supply relay for engine components J757 Secondary air pump relay J299 Secondary air pump motor V101 Injectors, cylinders 1 6 N30 N33, N83, N84 Intake camshaft timing adjustment valve -1- N205 Exhaust camshaft timing adjustment valve 1 N318 Lambda probes 1+2 heater Z19, Z28 Lambda probes 1+2 heater, after catalytic converter Z29, Z30 Coolant circulation pump V50 Radiator fan control unit J293, radiator fan V7 Radiator fan control unit J671, radiator fan 2 V177 Motronic power supply relay J271 Throttle valve drive (electronic power control) G186 Auxiliary signals: Gearbox mounting valve 1 N262 Ignition coils with power output stages 7 12 N325 N330 Injectors, cylinders 7 12 N85, N86, N299 N302 Intake camshaft timing adjustment valve 2 N208 Exhaust camshaft timing adjustment valve 2 N319 Lamdba probes 3+4 heater Z62, Z63 Lamdba probes 3+4 heater after catalytic converter Z64, Z65 Fuel metering valve 2 N402 Electro/hydraulic engine mounting solenoid valve, left N144

Throttle valve drive 2 G296 Secondary air pump solenoid valve 2 J545 Secondary air pump motor 2 V189 Exhaust ap valve 2 N322

Activated charcoal canister solenoid valve 1 N80 Auxiliary signals: Gearbox mounting valve 2 N263 Heating resistor (crankcase breather) N79 Tank leakage diagnostics control unit J9091)
33

490_020

Engine control unit J623 and engine control unit 2 J624

The engine control units operate according to the dual control unit concept. The Bosch MED17.1.6 engine management system is used. Both engine control units are housed in the plenum chamber and are of identical design. The control units are assigned to the cylinder banks by the "PIN coding" in the wiring harness. Both control units must always have the following features: Same software version CCS and ACC must be adapted Both must be treated separately in the self diagnostics Same coding

Engine control unit J623

Engine control unit 2 J624

490_050

34

Communication between control units

Both control units are powertrain CAN data bus users They have an internal private CAN for communicating with one another. It primarily serves the exchange of engine-specic data. It works in the same way as the powertrain CAN data bus.

PIN coding
Each engine control unit is assigned to a cylinder bank by the PIN coding within the wiring harness.

Ground connection in the wiring harness

Encoding PIN (PIN 21)

Encoding PIN (PIN 21)

+ 5volts (PIN 63)

Engine control unit 2 J624 (slave)

Engine control unit J623 (master)

Private CAN

Powertrain CAN databus

490_044

35

Important messages which are used by the engine control units

ACC control units J428 / J850 System states Torque request Start-stop information Airbag control unit J234 Crash intensity Seat belt status, driver side Trailer detector control unit J345 Brake light status Trailer detection Brake light monitoring Battery monitor control unit J367 Alternator output Radiator fan request Stop enable Automatic gearbox control unit J217 All relevant signals for engine torque adaptation Electromechanical park and handbrake control unit J540 Deceleration request Status of the EPB actuators ABS control unit J104 All signals relevant to the ESP Entry and start authorisation switch E415 Stop enable Start request Climatronic control unit J255 Engine speed increase requested before compressor activation Rear window defroster Windscreen defroster Air conditioning sys. on/o Start-stop signals Control unit in dash panel insert J285 Inoperative time Fuel tank lling status Ambient temperature Vehicle speed Steering column electronics control unit J527 Information from CCS and ACC switches Steer angle

Signals transmitted by the engine control unit J623 Engine torque Kick-down Fault memory Cylinder cutout Gearbox status Start-stop status Accelerator pedal values Engine speed ESP signals Oil level, min oil pressure warning Oil temperature Fuel consumption Radiator fan activation Vacuum OBD Recuperation enable signal AC adjustment Status of Audi drive select Radiator fan activation Information on replacement interval Activation of fault lamps Intake air temperature, intake manifold pressure Coolant temperature Altitude information Fault All information from the auxiliary heater System states of the engine, e.g. overrun Shut-down cylinders

36

Control units communicating with the engine control units

Vehicle elec. system control unit J519

Display and operation CAN

Control unit in dash panel insert J285

Door control unit, driver side J386

Convenience CAN

Diagnostic port

Information electronics control unit 1 J794

Diagnostics CAN Convenience system central control unit J393 Data bus diagnostic interface J533

Airbag control unit J234

AWD electronics control unit J492

MOST bus

Climatronic control unit J255

Auxiliary heater control unit J364

Entry and start authorisation control unit E415

LIN

LIN

Battery monitor control unit J367

Engine control unit J623

ABS control unit J104 FlexRay

Engine control unit 2 J624 Powertrain CAN

ACC control unit J428

Steering angle sender G85

ACC control unit 2 J850

Electromechanical park and handbrake control unit J540 Automatic gearbox control unit J217

490_051

Reference The gure shows a section of the topology of the Audi A810. For further information about the topology of the Audi A810, refer to Self Study Programme 459 "Audi A810 Onboard power supply and networking".

37

Exhaust system
Overview

Oxygen sensor 3 G285 Oxygen sensor 4 G286

Oxygen sensor G39 Oxygen sensor 2 G108 Oxygen sensor 4 after catalytic converter G288

Oxygen sensor 4 after catalytic converter G288 Oxygen sensor 3 after catalytic converter G287

Oxygen sensor after catalytic converter G130

Decoupling element

Front silencer (reection*/absorption silencer)

Centre silencer (absorption silencer*)

Working on the exhaust system

The rear silencer, centre silencer and tailpipe are supplied ex works as a unit (OEM equipment). If repair work is needed, however, the centre silencer and rear silencer can be replaced separately.

!
38

Note For information on the interface between the centre and rear silencers, as well as assembly work, please refer to the Workshop Manual.

Exhaust aps
A single exhaust ap is located on the tailpipes of the rear silencers on each side of the vehicle. The exhaust aps are tted to give the engine a sporty sound. The exhaust aps are operated in such a way as to meet the statutory limits for vehicle exterior noise. Low-frequency droning noise at low engine speeds is prevented. At high engine speeds and high exhaust gas ow rates, ow noise and exhaust backpressure are reduced by opening the additional cross-section. The exhaust gas aps are closed at idle, low engine load and low engine speeds.

Function
The exhaust aps are switched by a vacuum actuator. To ensure rapid switching of the exhaust aps, each vacuum actuator has an additional vacuum reservoir (see overview of vacuum supply on page 22). Both vacuum units are switched by an electrically activated solenoid valve: left: exhaust ap valve 1 N321 right: exhaust ap valve 2 N322

The exhaust aps are switched according to a characteristic map. The engine control units uses the following factors to plot the characteristic map: Engine load Engine speed Selected gear

X-pipe connection

Right exhaust ap vacuum actuator

Rear silencer (reection/absorption silencer)

Left exhaust ap vacuum actuator

490_026

39

Service
Special tools
Assembly tool T40251 Oil seal extractor T40249

490_045

490_046

Assembling the crankshaft oil seal on the pulley side

Disassembling the crankshaft oil seal on the pulley side

Thrust piece T40250

Thrust piece T10122/4

490_047

490_048

Assembling the cylinder head cover oil seal

Assembling the PTFE crankshaft oil seal on the power output side

Engine and gearbox mounting VAS 6095/01-12

490_049

40

Maintenance operations
Maintenance work Engine oil change interval with LongLife oil Interval Up to 30,000km or 24months depending on SID1) (change interval is dependent on driving style) Engine oil to VW standard 50400 Fixed interval of 15,000km or 12months (whichever occurs rst) Engine oil to VW standard 50200 or 50400 During every oil change 11.5litres (including oil lter) Extraction of the engine oil is not permitted.

Engine oil change interval without LongLife oil Engine oil lter change interval Engine oil change quantity (customer service) Engine oil extraction / drainage The engine still has no electronic oil gauge - a dipstick is provided for checking the oil level. Air lter change interval Fuel lter change interval Spark plug replacement interval

90,000 km Lifetime 60,000 km

1)

SID = Service Interval Display

Maintenance work Poly V belt replacement interval Poly V belt tensioning system Timing gear chain replacement interval Timing gear chain tensioning systems

Interval Lifetime Lifetime (automatic tensioner pulley) Lifetime Lifetime

41

Annex
Glossary
Absorption silencer An absorption silencer contains porous material, normally rock wool, glass wool or glass bre, which partially absorbs the sound energy by converting it to heat. The sound absorption eect is intensied by multiple reection. A 50dB(A) reduction in exhaust noise is possible, corresponding to a factor 300 reduction in sound pressure. Absorption principally attenuates high-band frequencies in the silencer. Brake energy recuperation Recuperation (Latin: "recuperare" = to recover, regain) is generally understood to describe the use of kinetic energy during deceleration phases of the vehicle. This means that the "free" energy produced during braking and overrun phases is recovered and stored in the vehicle battery.

TFSI Blow-by gases Blow-by gases are also known as leakage gases. When the engine is running, blow-by gases ow from the combustion chamber and past the piston into the crankcase. This is due to the high pressure inside the combustion chamber and the absolutely normal leakage that occurs around the piston rings. Blow-by gases are extracted from the crankcase by the positive crankcase ventilation system and re-introduced into the combustion chamber. This stands for Turbo Fuel Stratied Injection - a technology used by Audi on turbocharged petrol engines for the purpose of injecting fuel directly into the combustion chamber. Fuel is injected at pressures of more than 100 bar.

Dry-sump lubrication Dry-sump lubrication is a special type of forced-feed lubrication, where the oil pump supplies the engine lubrication points with fresh oil from a separate oil tank. This principle is applied to ensure an absolutely reliable oil supply even during extreme driving manoeuvres (longitudinal and transverse acceleration).

Impactor A system for separating liquid from a gas-uid mixture. The gases are channelled in such a way that their direction of ow changes sharply several times. Due to their inertia, the liquid components collide with the walls and drip down into a collection chamber.

Reection silencer The reection silencer comprises multiple (typically four) chambers designed to utilise the principle of sound reection. The sound pressure amplitude is averaged during multiple passes through the inner chambers, thus reducing the sound pressure peaks. Reections are produced in a silencer by baes, as well as crosssectional widenings and narrowings. However, the exhaust gas backpressure increases depending on the design. Reection principally attenuates low-band frequencies in the silencer.

42

Self Study Programmes

This Self-Study Programme summarises all the key information you need to know about the 6.3l W12 FSI engine. You will nd further information about the subsystems mentioned in this document in other Self-Study Programmes.

490_040

490_041

490_042

SSP 267 The 6.0l W12 engine on the Audi A8 - Part 1, order number: 140.2810.86.20 Engine mechanicals W engine concept SSP 268 The 6.0l W12 engine on the Audi A8 - Part 2, order number: 140.2810.87.20 Water-cooled alternator Variable camshaft timing SSP 432 The Audi 1.4l TFSI engine, order number: A08.5S00.48.20 Operating principle of the high-pressure fuel pumps

490_043

490_052

SSP 451 Audi TT RS with 2.5l R5 TFSI engine, order number: A10.5S00.67.20 Operating principle of the oil pump SSP 459 Audi A8 10 Onboard power supply and networking,order number: A10.5S00.63.20 Topology

43

All rights reserved. Technical specications are subject to change. Copyright AUDI AG I/VK-35 [email protected] AUDI AG D-85045 Ingolstadt Technical status 02/11 Printed in Germany A11.5S00.81.20

490

Audi Vorsprung durch Technik