Getting Started Using Adams Car MDR3

1
Introducing Adams/Car
Getting Started Using Adams/Car

2 Getting Started Using Adams/Car
Overview
This chapter introduces you to Adams/Car. It contains the following sections:
• Starting Adams/Car Standard Interface
• Starting Adams/Car Template Builder
• Switching Between Interface Modes
• Familiarizing Yourself with Adams/Car
• Plotting Results
3
Starting Adams/Car Standard Interface

In this section, you learn how to start Adams/Car Standard Interface in the Windows and the UNIX
environments.
In the Windows environment, you start Adams/Car from the Start button. In the UNIX environment, you
start Adams/Car from the Adams Toolbar. For more information, see the online help for Running and
Configuring Adams.
To start Adams/Car on Windows:

1. From the Start menu, point to Programs, point to MSC.Software, point to MD Adams R3,
point to ACar, and then select Adams - Car.
The Welcome dialog box appears on top of the Adams/Car main window.
2. Do one of the following:
• If the Welcome dialog box contains the options Standard Interface and Template Builder,
select Standard Interface, and then select OK.
• If the Welcome dialog box does not contain any options, then Adams/Car is already
configured to run in standard mode. Select OK.
The Adams/Car Standard Interface window appears as shown below. Familiarize yourself with
the Adams/Car window and read the tips in Familiarizing Yourself with Adams/Car.
Figure 1 Adams/Car Standard Interface

Menu bar
View triad
Status bar
Main shortcut menu
To start Adams/Car on UNIX:

1. At the command prompt, enter the command to start the Adams Toolbar, and then press Enter.
The standard command that MSC.Software provides is adamsmdx, where x is the version
number, for example adamsmdr3.
The Adams Toolbar appears.
2. Click the Adams/Car icon
5
3. Do one of the following:

• If the Welcome dialog box contains the options Standard Interface and Template Builder,
select Standard Interface, and then select OK.
• If the Welcome dialog box does not contain any options, then Adams/Car is already
configured to run in standard mode. Select OK.
The Adams/Car Standard Interface window appears as shown above. Familiarize yourself with
the Adams/Car window and read the tips in Familiarizing Yourself with Adams/Car.
Starting Adams/Car Template Builder

Before you start Adams/Car Template Builder, make sure that your private configuration file,
.acar.cfg, shows that you can work in expert-user mode. Your private configuration file is located in
your home directory.
To check the user mode:

1. In a text editor, such as jot or notepad, open .acar.cfg.
2. Verify that the following line appears as shown:
ENVIRONMENT MDI_ACAR_USERMODE expert
This line sets the user mode for the Adams/Car session.
To start Adams/Car Template Builder on Windows:

1. From the Start menu, point to Programs, point to MSC.Software, point to MD Adams R3, point
to ACar, and then select Adams - Car.
2. Select Template Builder.
3. Select OK.
The Adams/Car Template Builder window appears as shown in the figure below. Familiarize
yourself with the Adams/Car window and read the tips in Familiarizing Yourself with Adams/Car.
Figure 2 Adams/Car Template Builder

7
Menu bar
Menus grayed out because

you don’t have a template yet
Main shortcut menu
View triad Status bar
To start Adams/Car Template Builder on UNIX:

1. At the command prompt, enter the command to start the Adams Toolbar, and then press Enter.
The standard command that MSC.Software provides is adamsmdx, where x is the version
number, for example adamsmdr3.
The Adams Toolbar appears.
2. Click the Adams/Car icon .

3. Select Template Builder.

4. Select OK.
The Adams/Car Template Builder window appears as shown in the figure above. Familiarize
yourself with the Adams/Car window and read the tips in Familiarizing Yourself with Adams/Car.
9
Switching Between Interface Modes

Once you have started Adams/Car in the Standard Interface or Template Builder modes, you can easily
switch between them.
To switch between modes:

• In Standard Interface: From the Tools menu, select Adams/Car Template Builder.
• In Template Builder: From the Tools menu, select Adams/Car Standard Interface.
Familiarizing Yourself with Adams/Car

Take a few minutes to familiarize yourself with the Adams/Car main window.
The following tips help you quickly become familiar with Adams/Car:
• You use the menus along the top of the window to execute commands and display dialog boxes.
Notice that some menus are shaded in grey. This indicates that you cannot execute these
commands because you do not have a subsystem open. When you open a subsystem, these
menus change to black indicating that you can execute the commands.
• You can use the main shortcut menu to execute simple commands, such as rotating views,
zooming, and fitting assemblies in the main window. To display the main shortcut menu, right-
click in the main window, away from any entities.
• Instead of manually entering text in boxes that require database objects, you can have
Adams/Car automatically do this task for you. To do this, right-click the text box of interest, and
then select an option. For example, if you were modifying a hardpoint, Adams/Car would
present you with the following options:
• Point to Hardpoint (or the entity of interest) and then select Pick. On the main window, place
the cursor on top of the hardpoint. When the name of the hardpoint appears, you can click the
left mouse button to select that hardpoint.
• Point to Hardpoint, and then select Guesses. From the pop-up menu that appears, select the
entity name you want to use.
• Point to Hardpoint, and then select Browse. Adams/Car displays the Database Navigator,
which contains a list of entities, hardpoints in this case. Double-click the entity name you want
to use.
11
Plotting Results
When you’re ready to review the results of your analyses, you can display the post-processing tool and
view the results of the simulations you performed.
To plot results:
1. While in Adams/Car Standard Interface, from the Review menu, select Postprocessing Window
or press F8.
Adams/Car launches Adams/PostProcessor, a post-processing tool that lets you view the results
of simulations you performed. For more information about Adams/PostProcessor, see the
Adams/PostProcessor online help.
2. To return to Adams/Car, select the Return to Modeling Environment tool or press F8.
13
Introducing the Driving Machine

Overview
This tutorial introduces you to the Driving Machine and the associated Event Builder. It contains the
following sections:
• About the Driving Machine
• About the Event Builder
15
About the Driving Machine

You can use Adams/Car and Adams/Chassis to study full-vehicle behavior for many different aspects of
vehicle development, such as handling, ride, and durability.
Both Adams/Car and Adams/Chassis offer several standard full-vehicle analyses (ramp steer, straight
line braking, and so on) allowing engineers and analysts to quickly characterize certain vehicle attributes.
In addition to standard full-vehicle analyses, the Driving Machine supports an XML event file that lets
you create your own custom full-vehicle analyses. These analyses are typically built from a number of
mini-maneuvers, which when simulated in succession, define a meaningful vehicle test. An example of
such a test could be a braking-in-turn analysis, which would consist of the following mini-maneuvers:
1. Drive along a road in a straight line, maintaining a constant velocity. When a constant velocity
has been achieved for a specified amount of time and within a prescribed tolerance, end the first
mini-maneuver.
2. Start the second mini-maneuver by steering the vehicle onto a prescribed radius and maintaining
the same velocity. When the velocity has stabilized for a set amount of time and within a
prescribed tolerance, end the second mini-maneuver.
3. Start the third mini-maneuver by maintaining the previous radius and velocity from the second
mini-maneuver. After a two-second delay, apply the brake to achieve a desired longitudinal
deceleration while maintaining the radius from the second mini-maneuver by controlling the
steering wheel.
For a human driver, this is quite a simple task: you simply drive in a straight line, turn the steering wheel,
and then apply the brake. In the Adams/Car and Adams/Chassis environment, you have more control
over the driving event. Such an analysis requires a reasonably complex event file.
Looking at the mini-maneuvers described above, the control attributes for each mini-maneuver are.
• Steering wheel has to keep the vehicle straight. Throttle has to maintain vehicle speed. Gear,
clutch, and brake are not used.
• Steering wheel has to steer the vehicle, then control the radius of turn. Throttle has to maintain
vehicle speed. Gear, clutch, and brake are not used.
• Steering wheel has to maintain the radius of turn (steering motion will change during braking
based on the understeer/oversteer characteristics of the vehicle). Brake pedal has to be applied
and controlled to achieve the desired lateral acceleration. Throttle has to be lifted. Application of
the clutch will need to be considered also.
The Driving Machine permits a fine level of control over the full-vehicle model. This control has
historically been exercised by using a .dcf file, which is based on the TeimOrbit data file standard. The
Driving Machine now uses XML event files to describe mini-maneuvers. You can still access .dcf files,
however, Driving Machine automatically converts them to XML event file format.
About the Event Builder

The Event Builder lets you create and modify XML event files. The information in a new full-vehicle
analysis is then saved in an .xml-based file, which can be used in the driving control file full-vehicle
analysis.
The Event Builder consists of two distinct interfaces:
• The mini-maneuver creation interface - Used to quickly create the mini-maneuvers; there is no
limit to the number of mini-maneuvers that can be created.
• The mini-maneuver editor - Used to specify the Driving Machine parameters for each separate
mini-maneuver. In the example maneuver specified earlier, you would first create three mini-
maneuvers, then fill in the details for each mini-maneuver (steering, throttle, clutch, gear, brake,
and end conditions). In this tutorial, you will go through this process.
17
Using the Event Builder

Overview
In this chapter, you will learn the basics of creating multiple mini-maneuvers, establishing the
appropriate application areas for those mini-maneuvers, and setting end conditions for each mini-
maneuver.
The chapter contains the following sections:
• Creating an Event
• Creating the Three Mini-Maneuvers
• Defining the Mini-Maneuver Parameters
• Running the New Analysis
19
Creating an Event
Before you can create an event, you must create a new file, as explained next. The instructions will point
out differences between procedures in Adams/Car and Adams/Chassis, as needed.
To display the Event Builder:

• Do one of the following, depending on your Adams product.
In Adams/Car:
• Open the assembly MDI_DEMO_VEH.
• From the Simulate menu, point to Full-Vehicle Analysis, and then select Event Builder.
In Adams/Chassis:
• In Build mode, from the toolbar, select the Load Example Model button .
• Adams/Chassis displays the default example model.
• From the Test mode bookshelf, select Full-Vehicle, select Handling Analysis, and then
double-click Standard Driver Interface (SDI).
• From the property editor, select the Edit button .
Your Adams product displays the Event Builder, which is grayed out because you do not have a
.xml file yet.
To create a new file:

1. From the Event Builder’s File menu, select New.
The New File dialog box appears.
2. Enter the name of the event: braking_in_a_turn. This is the name of the file that will be saved
to your hard drive or network drive with a .xml extension.
3. Select OK.
Your Adams product creates the file and also defines the first mini-maneuver, MINI_1.
Entering Set-up and Global Parameters

The top of the Event Builder window, as shown next, has three fields and two tabs that provide global
parameters and set initial conditions.
The Event File text box shows the file name you specified when you created or opened the file, and
the path, for new files, is the working directory. You can’t change the file name or path in the Event
Builder. You can use the Speed and Gear text boxes to enter an initial speed and gear, respectively, for
the vehicle prior to starting the first mini-maneuver.
The Static Set-up tab lets you complete the definition of the vehicle state prior to beginning of the
first mini-maneuver. The Gear Shifting Parameters tab lets you define global parameters
related to gear shifting. The Event Builder outputs this information so that the Driving Machine uses
these parameters for any shifting required by any mini-maneuver.
For this exercise, the default Gear Shifting Parameters should be adequate, so you won’t change them.
Because the first mini-maneuver that you specify is going to be a straight line, you will use the straight
static setup. For a description of the static setup methods available in the Driving Machine, see the
Analyze tab in the Adams/Car online help.
1. In the Static Set-up tab, change set Task to straight. Note that the rest of the parameters
are not used because they will be overwritten by the initial values computed during the quasi-
static setup.
You must set the initial velocity of the vehicle. The value of the initial velocity depends on the
units in which you are using the Event Builder.
2. To check the units or make a change, from the Settings menu, select Units.
21
By default, the length unit is set to meters and the time unit is set to seconds. Therefore, the
velocity must be set in meters/second.
3. To verify that velocity units are in meters/second, click in the Speed text box at the top of the
Event Builder, and then read what is displayed in the Current Field Unit text box at the bottom
of the Event Builder.
4. To set the target vehicle velocity, in the Speed text box, enter 27.7 (as previously explained, units
are meters/second), which corresponds to approximately 100 km/h.
5. To set the initial gear, in the Gear text box, enter 5.
Creating the Three Mini-Maneuvers

To complete the braking-in-turn event, you must create three mini-maneuvers.
To create the mini-maneuvers:

1. To go to the mini-maneuver table editor, select .
The mini-maneuver table editor appears. Note that by default, the first mini-maneuver, MINI_1,
is already defined.
2. To create one more mini-maneuver, in the Name text box at the bottom of the Event Builder
window, enter MINI_2, and then select Add.
3. To create the last mini-maneuver, in the Name text box, enter MINI_3, and then select Add.
The mini-maneuver window appears as follows:
4. In the Abort Time for MINI_2, change the abort time to 5.

5. To save the mini-maneuver, select Save.
Your Adams product saves the file, braking_in_a_turn.xml, in your current working
directory.
23
Defining the Mini-Maneuver Parameters

Now that you defined the three mini-maneuvers, you must define what each of the application areas and
end conditions will do during the mini-maneuvers.
The application areas are steering, throttle, brake, clutch, and gear. For each application area, you define
the Driving Machine control (open loop, closed loop, Adams/SmartDriver, or human).
End conditions define a vehicle state that the Driving Machine uses to terminate a mini-maneuver. End
conditions are extremely flexible, and let you define many types of situations that cause the vehicle state
to move on to the next mini-maneuver. The following are some example end conditions:
• End conditions can have a single condition, such as time is greater than 5 seconds.
• End conditions can have a single value that must be within a tolerance over a prescribed period
of time. Lateral acceleration is 0.5 g over a two-second period and within a 0.05 g tolerance.
• Multiple end conditions, such as time is greater than 5 seconds or vehicle velocity is lower than
10 kph.
• Combined end condition, such as vehicle velocity equal 100 kph (within a tolerance) and
longitudinal acceleration equals 0 g (within a tolerance). Event Builder lets you group end
conditions, allowing you to specify multiple conditions required to terminate a maneuver.
For more information on end conditions, see the Analyze tab in the Adams/Car online help.
To define mini-maneuver parameters for MINI_1:

1. To access the mini-maneuver property editor, double-click the name of the mini-maneuver you
want to edit. In this case, MINI_1.
2. For the first mini-maneuver, the vehicle should drive in a straight line and maintain constant
velocity. To achieve this, set the following parameters:
• Steering tab
Actuator Type: rotation
Control Method: machine
Control Mode: Absolute
Steer Control: straight
The Steer Control setting enables the Driving Machine to drive the vehicle in a straight line.
• Throttle tab
Speed Control: maintain
Velocity: 27.7
The Velocity setting enables the Driving Machine to maintain the steady-state velocity that
you established earlier. The Driving Machine will control the throttle to maintain this velocity
much like a cruise control system.
• Braking tab
The Throttle and Brake settings control the longitudinal velocity of the vehicle.
• Gear tab
Control Method: open
Control Type: constant
Control Value: 5
Maintain the same gear specified for the static setup.
• Clutch tab
Control Value: 0.0
For the first mini-maneuver, you’re using the Driving Machine for the steering and the
throttle, so you can maintain the vehicle speed during straight-line driving.
The purpose of the first mini-maneuver is to reach a dynamic steady-state end condition.
Although not absolutely necessary for this type of event, it helps demonstrate some important
aspects of the Driving Machine. To satisfy a steady-state condition, the vehicle must be
traveling a straight line (very low lateral acceleration) at a stable velocity (very low
longitudinal velocity). You can use end conditions to group these two conditions together to
satisfy the steady-state requirements.
To create end conditions for MINI_1:

1. Select the Conditions tab.
2. Select .
3. In the Name text box, enter END_2.
4. Select Add.
5. Modify the end conditions as follows:
• END_1
Type: lon_accel
Test : ==
Trigger Value: 0.0
Error: 0.05
Filter Time: 2.0
Delay Time:0.0
25
Group Name: MINI_1

• END_2
Type: lat_accel
Test : ==
Trigger Value: 0.0
Error: 0.05
Filter Time: 2.0
Delay Time: 0.0
Group Name: MINI_1
Note that you used MINI_1 for both group names. Because END_1 and END_2 have the
same Group Name, the vehicle state must satisfy both end conditions for the maneuver
switch to occur.
6. Select Save.

1. Select to the left of Name label for the text box containint MINI_1.
2. Double-click on the name of the mini-maneuver, MINI_2.
3. Set the mini-maneuver parameters as follows:
• Steering tab
Actuator: rotation
Steer Control: skidpad
Entry Distance: 20.0
Radius: 120
Turn Direction: Right
These parameters will start the vehicle turning at the beginning of the second mini-maneuver.
• Throttle tab
Speed Control: maintain
Velocity: 27.7
These parameters allow the Driving Machine to maintain the straight line velocity established
in MINI_1. The steering parameters established in the steering block are not modified.
• Braking tab

• Gear tab
Control Value: 5
Maintain the same gear specified for the static setup.
• Clutch tab
Control Value: 0.0
For the second mini-maneuver, you’re tellling the Driving Machine to make a right turn and
control the vehicle on a radius of 120 m.
Next, you will create two end conditions to verify that the vehicle has reached a steady-state
cornering condition.
To create end conditions for MINI_2:

3. Select Add.
4. Create the second end condition, END_2, just as you created the first.
5. Modify the end conditions as follows:
• END_1
Condition Type: lon_accel
Test Type: ==
Trigger Value: 0.0
Error: 0.05
Filter Time: 2.0
Delay Time: 0.0
Group Name: MINI_2
• END_2
Condition Type: curvature
Test Type: ==
Trigger Value: 0.00833
Error: 0.00005
Filter Time: 2.0
27
Delay Time: 0.0

Group Name: MINI_2
These end conditions ensure that a radius of approximately 120 m is followed at a velocity of
100 kph.
6. Select Save.

1. Select .
2. Double-click on the name of the mini-maneuver, MINI_3.
3. Set the mini-maneuver parameters as follows:
• Steering tab
Actuator: rotation
Steer Control: skidpad
Entry Distance: 0.0
Radius: 120
Turn Direction: Right
These parameters maintain the radius from the previous mini-maneuver.
• Throttle tab
Control Method:machine
• Braking tab
Speed Control: lon_accel
Start Time: 1.0
Long. Acc.: - 3.0
These parameters drop the throttle at the beginning of the third mini-maneuver to zero, and
control the deceleration to 3.0 m/s2.
• Gear tab
The Driving Machine controls the gear selection.
• Clutch tab
The Driving Machine controls the clutch selection.
For the third mini-maneuver, you use the Driving Machine for all vehicle activity; you want
the Driving Machine to maintain the vehicle radius while at the same time braking the vehicle
at 3 m/s2. You use a single end condition for the third mini-maneuver, which is velocity. You
trigger the end of the simulation if the velocity is below 10 kph which is approximately
2.77 m/s.
To create the end condition for MINI_3:

3. Select Add.
4. Modify the end condition as follows:
• END_1
Condition Type: velocity
Test Type: <<
Trigger Value: 2.77
Error:0.01
Filter Time: 0.0
Delay Time: 0.0
5. Select Save. You can then select Cancel to close the Event Builder window.
By default, your Adams product saves the file in the current working directory. If you are not sure
where the current working directory is located, do following:
• In Adams/Car, from the File menu, select Select Directory.
This displays a dialog that shows the current working directory.
• In Adams/Chassis, from the Edit menu, select Preferences.
The Current Working Directory text box shows the directory location.
29
Running the New Analysis

To run the new analysis:
1. Do one of the following, depending on your Adams product.
In Adams/Car:
• From the Simulate menu, point to Full-Vehicle Analysis, and then select File Driven
Events.
• Double-click the Driver Control Files text box to display a file selection dialog box that
already points to your working directory. Then, double-click the name of the new event file
you created in this tutorial (braking_in_a_turn.xml).
• In the Output Prefix text box, enter Event_Build.
• Leave the other parameters set to their defaults. For help on filling out this dialog box, press
F1.
• Select OK to run the analysis.
In Adams/Chassis:
• To select the event file (braking_in_a_turn.xml), select the File Open button .
• Run the analysis.
You are now ready to use the Event Builder to run full-vehicle analyses.
31
Suspension Analysis Tutorial

This tutorial teaches you how to modify and analyze a double-wishbone suspension.
This chapter includes the following sections:
• What You Will Create and Analyze
• Setting Up the Suspension and Steering Subsystems
• Performing a Baseline Parallel Wheel Travel Analysis
• Performing a Baseline Pull Analysis
• Modifying the Suspension and Steering Subsystem
• Performing an Analysis on the Modified Assembly
• Comparing the Analysis Results
• Finishing Up
This tutorial takes about one hour to complete.

What You Will Create and Analyze

During this tutorial, you analyze and modify an assembly of a front suspension and steering subsystem.
To perform the analysis, you must first create a double-wishbone suspension and steering subsystem
from standard Adams/Car templates and subsystems. Adams/Car templates define a subsystem’s
topology and specify how one subsystem connects to another. Templates also contain default parameters,
such as locations, part masses, and inertias.
The figure shows the suspension and steering assembly (in shaded mode) that you will analyze and
modify.
Figure 3 Suspension and Steering Assembly
After you create the suspension and steering assembly, you perform two types of analyses to understand
its kinematics:
33
• A baseline parallel wheel travel analysis that moves the assembly vertically through the
suspension’s rebound-bump travel.
• A baseline pull analysis to measure the brake pull at the steering wheel.
Once you understand the kinematics of the assembly, you modify the suspension subsystem’s geometry
to decrease the scrub radius, which should reduce the pull on the steering wheel. You confirm the
reduction by analyzing the modified assembly again, using the same type of analysis and comparing the
new results to the results yielded by the previous analysis.
Setting Up the Suspension and Steering Subsystems

In this section, you work with a suspension and steering assembly from two subsystems: a suspension
subsystem and a steering subsystem. You create the suspension subsystem using the standard double-
wishbone template. You don’t need to create the steering subsystem. Instead, you can open an existing
subsystem that we’ve provided.
After creating and opening the subsystems, you create an assembly that contains the subsystems and a
test rig.
Creating a New Front Suspension Subsystem

You create the front suspension subsystem based on a double-wishbone design stored in the standard
template named _double_wishbone.tpl, and then save it.
After you create the subsystem, you save it in an Adams/Car database. When you save a subsystem,
Adams/Car stores it in the database designated as the default writable database. Initially, the private
database is the default writable database, but as you become more familiar with Adams/Car, you can
change your writable database. Later, when you are sure the design is complete or ready for review, you
can have your database administrator save the file in a shared database or allow others to access it from
your private database.
To create the front suspension subsystem:

1. Start Adams/Car Standard Interface as described in Starting Adams/Car Standard Interface.
2. From the File menu, point to New, and then select Subsystem.
The New Subsystem dialog box appears.
Tip: For information on any dialog box, press F1 when the dialog box is active.
3. In the Subsystem Name text box, enter UAN_FRT_SUSP.

4. Set Minor Role to front. A minor role defines the subsystem’s function and its placement in the
assembly (for example, front or rear). In this case, you select front because you are creating a front
suspension.
5. Right-click the Template Name text box, point to Search, and then select the acar_shared
database.
The Select File dialog box appears.
6. Double-click _double_wishbone.tpl.
The Template Name text box now contains the file _double_wishbone.tpl and an alias to
its directory path.
7. Verify that Translate from default position is not selected.
8. Select the Comment tool .
The Modify Comment dialog box appears.
35
9. In the Comment Text text box, enter Baseline UAN Front Suspension.
10. Select OK.
11. Select OK again.
Adams/Car creates the suspension subsystem using the default data contained in the template and
displays it as shown next:
Figure 4 Suspension Subsystem
To save the suspension subsystem:

• From the File menu, select Save.
Adams/Car saves the subsystem in your default writable database, which might be your private
database. For more information on databases, see the Adams/Car online help.
Creating a Suspension Assembly

In this section, you create a new suspension assembly and add to it a steering subsystem.
To create the suspension assembly:

1. From the File menu, point to New, and then select Suspension Assembly.
The New Suspension Assembly dialog box appears.
2. In the Assembly Name text box, enter my_assembly.
3. Click the folder icon next to Suspension Subsystem.
The name of the suspension subsystem you just created appears.
4. Select Steering Subsystem.
5. Right-click the Steering Subsystem text box, point to Search, and then select the acar_shared
database.
The Select File dialog box appears.
6. Double-click MDI_FRONT_STEERING.sub.
The Steering Subsystem text box now contains MDI_FRONT_STEERING.sub and an alias to
its directory path.
Note that by default Adams/Car selects a test rig for the assembly,
__MDI_SUSPENSION_TESTRIG.
7. Select OK.
The Message Window appears, informing you of the steps Adams/Car takes when creating the
assembly.
Adams/Car displays the suspension and steering assembly in the main window.
8. Select Close, to close the Message Window.
37
Performing a Baseline Parallel Wheel Travel Analysis

You now perform a parallel wheel travel analysis on the suspension and steering assembly, and then plot
and view the results, as explained in the following sections:
• Defining Vehicle Parameters
• Performing the Analysis
• Animating the Results
• Plotting the Results
Defining Vehicle Parameters

Before performing a suspension analysis, you must specify several parameters about the vehicle in which
you intend to use the suspension and steering subsystems. These parameters include the vehicle’s wheel
base and sprung mass, whether or not the suspension is front- or rear-wheel drive, and the braking ratio.
For this analysis, you enter the parameters to indicate front-wheel drive and a brake ratio of 64% front
and 36% rear.
To define vehicle parameters:

1. From the Simulate menu, point to Suspension Analysis, and then select Set Suspension
Parameters.
The Suspension Analysis: Setup Parameters dialog box appears. It contains default settings to
help you quickly set up a suspension analysis.
2. Set up the analysis as follows:
• Suspension Assembly: my_assembly
• Tire Model: User Defined
• Tire Unloaded Radius: 300
• Tire Stiffness: 200
• Wheel Mass: 10.0
• Sprung Mass: 1400
• CG Height: 300
• Wheelbase: 2765
• Drive Ratio: 100
All driving force is applied to the front wheels.
• Brake Ratio: 64
The brake ratio value indicates the % of braking force that is applied to the front brakes.
3. Select OK.
Performing the Analysis

Now that you’ve defined the vehicle parameters, you can run the parallel wheel travel analysis. During
the analysis, the test rig applies forces or displacements, or both, to the assembly, as defined in a loadcase
file. For this analysis, Adams/Car generates a temporary loadcase file based on the inputs you specify.
This parallel wheel travel analysis moves the wheel centers from -100 mm to +100 mm relative to their
input position, while holding the steering fixed. During the wheel motion, Adams/Car calculates many
suspension characteristics, such as camber and toe angle, wheel rate, and roll center height.
To perform the analysis:

1. From the Simulate menu, point to Suspension Analysis, and then select Parallel Wheel Travel.
• Output Prefix: baseline
• Number of Steps: 15
• Mode of Simulation: interactive
• Bump Travel: 100
• Rebound Travel: -100
• Travel Relative To: Wheel Center
• Steering Input: Angle
3. Select the Comment tool .
4. In the Comment Text text box, enter Baseline Parallel Wheel Travel Analysis.
5. Select OK.
6. Select OK again.
The Message Window appears, informing you of the steps Adams/Car takes when performing the
analysis. Adams/Car analyzes the suspension and steering assembly and applies to it the
displacements and loads defined in the submission dialog box.
7. When the analysis is complete, select Close.
Animating the Results

In this section, you view the analysis you just ran. Adams/Car has already loaded the animation and
graphic files for you.
To animate the results:

1. From the Review menu, select Animation Controls.
2. Select the Play tool .
39
Adams/Car animates the motion of the suspension analysis. Notice that the suspension moves
from rebound (down), to bump (up), and that the steering wheel does not rotate.
3. When the animation is complete, close the dialog box.
Plotting the Results

In this section, you create several plots from the parallel wheel travel analysis results. In a plot
configuration file, we have provided all the information that Adams/Car needs to create the plots. The
plot configuration file not only specifies which plots Adams/Car should create, but also how the plots
should look, including their horizontal and vertical units, and colors. Storing plotting information in a
plot configuration file lets you quickly regenerate plots after each analysis.
To plot the results:

1. Launch Adams/PostProcessor as explained in Plotting Results.
2. From the Plot menu, select Create Plots.
3. Enter the following specifications:
• Plot Configuration File:mdids://acar_shared/plot_configs.tbl/mdi_suspension_short.plt
• Plot Title: Baseline Parallel Travel Analysis - UAN_FRT_SUSP
4. Select OK.
Adams/Car creates the plots. To cycle through the plots, from the Main toolbar, use the Previous
Pages and Next Pages tools .
5. View the plot named Scrub Radius, shown next. Scrub radius is the distance from the point
at the intersection of the steering axis (also known as the kingpin axis) and the ground plane, to
the line of intersection of the wheel and ground planes.
Plot of Scrub Radius versus Wheel Travel
Notice that the scrub radius varies little with wheel travel and is approximately 34 mm. A positive
scrub radius means the steering axis lies inboard of the center of the tire contact patch.
From the analysis you’ve completed, you have enough information to calculate the approximate
torques produced about the steering axes using the difference in left to right braking forces and
the 34 mm scrub radius.
In addition, using the results of that calculation and the steering geometry, you can calculate the
resulting unbalanced force at the steering rack and the pull (torque) needed at the steering wheel
to keep the wheels straight.
In the next sections, you use Adams/Car to perform these calculations.
Deleting Plots
To prepare for the baseline pull analysis, delete the plots you created in the previous sections.
To delete plots:
1. In the treeview, hold down the left mouse button, and then drag the cursor across the names of the
plots you want to delete.
2. From the Edit menu, select Delete.
3. From the File menu, select Close Plot Window or press F8.
Adams/Car returns to the main window.
41
Performing a Baseline Pull Analysis

You can now perform a baseline pull analysis to study the pull on the steering wheel. You will use the
results of this pull analysis as the baseline against which you compare the results of another pull analysis
that you perform after you modify the location of the steering axis. By comparing the results from the
two analyses, you can determine if the modifications were successful.
Performing a baseline pull analysis involves the following:
• Defining a Loadcase File
• Performing the Analysis
• Saving the Plot Configuration
Defining a Loadcase File

Before you can run the baseline pull analysis, you need to create a loadcase file to drive the analysis. In
the loadcase file, you specify the unequal braking forces to simulate braking on a split-μ surface and the
beginning, or upper, and ending, or lower, steering wheel angles.
To calculate the unequal brake forces, we assume that the vehicle is braking at a rate of 0.5 g’s
deceleration, with a 64% front and 36% rear brake ratio, a vehicle mass of 1,400 kg, and the front braking
force split 55% left and 45% right. Based on these assumptions, the total front braking force is:
1,400 kg * 0.5 g’s * 9. 81 m/s2/g * 0.64 = 4,395 N

From this, the left and right braking forces are:
• Left braking force = 0.55 * 4,395 N or 2,417 N
• Right braking force = 4,395 N - 2,417 N or 1,978 N
You can use these calculations to define the loadcase file.
To define a loadcase file:

1. From the Simulate menu, point to Suspension Analysis, and then select Create Loadcase.
Note: If Select Loadcase Type is not set to Static Load, your dialog box will look slightly
different. Make sure you select Static Load first, and then proceed to fill in the dialog box.
2. Fill in the dialog box as shown next, and then select OK.
Adams/Car creates the loadcase file, named brake_pull.lcf, and stores it in your private
database. It stores the loadcase file as text (ASCII) and you can print it or edit it manually.
To create the loadcase file, Adams/Car takes the parameters that you entered and generates a table
of input values. For the parameters that you entered, Adams/Car generates a table that varies
steering wheel angle from -180 to 180 in 15 steps, while holding the braking forces constant.
Table 1 shows the loadcase file values
43
Table 1 Loadcase file values

Steering Left Brake Right Brake
Wheel: Force: Force:
-180 2417 1978
-156 2417 1978
-132 2417 1978
-108 2417 1978
-84 2417 1978
-60 2417 1978
-36 2417 1978
-12 2417 1978
12 2417 1978
36 2417 1978
60 2417 1978
84 2417 1978
108 2417 1978
132 2417 1978
156 2417 1978
180 2417 1978
Performing the Analysis

You can now use the loadcase file that you just created to perform an analysis that determines the pull
characteristics of the suspension and steering assembly.
To perform the pull analysis:

1. From the Simulate menu, point to Suspension Analysis, and then select External Files.
• Output Prefix: baseline
• Mode of Simulation: interactive
• Loadcase Files: mdids://private/loadcases.tbl/brake_pull.lcf
3. Make sure Load Analysis Results is selected.
4. Select OK.

In this section, you view an animation of the analysis Adams/Car just performed.

2. Select the Play tool.
Adams/Car animates the turning motion of the steering subsystem. You should see the wheels
turn as the steering wheel rotates. The wheel centers should not move vertically.
3. Close the Animation Controls dialog box.

You can now use the results from the baseline pull analysis to create two plots, as explained in the
following sections:
• Plotting Steering Wheel Torque versus Steering Wheel Angle
• Plotting Scrub Radius versus Steering Wheel Angle
Plotting Steering Wheel Torque versus Steering Wheel Angle

You now create a plot of the steering wheel torque versus the steering wheel angle.
To set up the plot:

1. Launch Adams/PostProcessor just as you did before.
2. From the treeview, double-click page_1.
3. Select plot_1.
4. In the property editor, clear the selection of Auto Title and Auto Subtitle.
5. In the Title text box, enter Brake Pull Analysis.
6. In the Subtitle text box, enter Steering Wheel Torque vs Steering Wheel Angle.
7. Right-click the treeview area, point to Type Filter, point to Plotting, and then select Axes.
8. From the treeview, double-click plot_1, and then select haxis.
9. In the property editor, select the Labels tab.
10. In the Label text box, enter Steering Wheel Angle [degrees].
11. From the treeview, select vaxis.
12. In the Label text box, Steering Wheel Torque [Nmm].
To create the plot:

1. Verify that Source is set to Requests.
Adams/Car automatically displays data information.
45
2. From the Simulation list, select baseline_brake_pull.

3. From the right of the dashboard, set Independent Axis to Data.
The Independent Axis Browser appears. You perform the next four steps in the browser.
4. From the Filter list, select user defined.
5. From the Request list, select steering_displacements. You might have to scroll down to see this
entry.
6. From the Component list, select angle_front.
7. Select OK.
9. From the Request list, expand test rig in the Request list, and then select steering_wheel_input.
10. From the Component list, select steering_wheel_input_torque.
11. Select Add Curves.
Adams/Car takes the data requested and automatically generates the curve on the current plot
template, as shown next:
Figure 5 Plot of Steering Wheel Torque versus Steering Wheel Angle

The plot shows the torque that the test rig applies to the steering wheel to hold the wheel in
position. The torque is negative, meaning that the test rig applies a clockwise torque to counteract
the unequal braking force that pulls the wheel counterclockwise, as if making a left turn.
Plotting Scrub Radius versus Steering Wheel Angle

In this section, you create a plot of the scrub radius versus the steering wheel angle. After you create the
plot, you can modify it to change the number of divisions in the vertical and horizontal axes so they cover
a larger range and define the minimum and maximum limits to be displayed in the vertical axis.
To set up the plot:

1. From the Main toolbar, select the New Page tool .
2. In the treeview, double-click page_2.
3. Select plot_2.
4. Make sure that Auto Title and Auto Subtitle are not selected.
5. In the Title text box, enter Brake Pull Analysis.
6. In the Subtitle text box, enter Scrub Radius vs Steering Angle.
47
7. Right-click the treeview area, point to Type Filter, point to Plotting, and then select Axes.
8. Double-click plot_2 to expand it so the names of the axes are visible.
9. From the treeview, select haxis.
10. In the property editor, select Labels.
11. In the Label text box, enter Steering Wheel Angle [degrees].
12. From the treeview, select vaxis.
13. In the Label text box, enter Scrub Radius [mm].
To create the plot:

2. From the Simulation list, select baseline_brake_pull.
4. From the Request list, select scrub_radius.
5. From the Component list, select left.
This defines the vertical axis component.
Adams/Car takes the data requested and generates the curve on the current plot template, as
shown next:
Figure 6 Plot of Scrub Radius versus Steering Angle

Notice that the scrub radius appears to vary a lot with respect to the steering angle because of the
vertical plot scale, when in fact it only varies 0.21 mm over the total range of steering wheel angle.
To show that this variation is small, you must modify the vertical axis so it covers a larger range
of values.
To modify the plot:

1. Select the vertical axis.
2. From the property editor, select the Format tab.
3. Clear the selection of Auto Scale.
4. In the Limits text boxes, enter 0 and 100.
A modified plot appears as shown next.
Figure 7 Modified Plot of Scrub Radius versus Steering Wheel Angle

49
Notice that the variation in scrub radius with respect to the steering wheel angle now appears
smaller.
Saving the Plot Configuration

Saving the changes that you made to the plots in a plot configuration file lets you easily recreate the plots
later in this tutorial, after you modify the suspension and steering assembly.
To save the plot configuration:

1. From the File menu, point to Export, and then select Plot Configuration File.
2. In the Configuration File Name text box, enter brake_pull.
3. Make sure All Plots is selected.
4. Select OK.
5. From the File menu, select Close Plot Window or press F8.
Modifying the Suspension and Steering Subsystem

For a double-wishbone suspension, the line running from the lower spherical joint to the upper spherical
joint defines the steering axis or kingpin axis. If these joints move outboard while the rest of the
suspension geometry remains unchanged, the scrub radius is decreased.
In the suspension subsystem that you created, two hardpoint pairs define the locations of these joints:
• hpl_lca_outer and hpr_lca_outer, where lca_outer means lower control arm
outer, and the prefix hpl means hardpoint left and the prefix hpr means hardpoint right.
• hpl_uca_outer and hpr_uca_outer, where uca_outer means upper control arm outer and the
prefix hpl means hardpoint left and the prefix hpr means hardpoint right.
Hardpoints define independent locations in space.
To decrease the scrub radius, you modify the locations that these hardpoints define, as explained in the
following sections:
• Modifying Hardpoint Locations
• Saving the Modified Subsystem
Modifying Hardpoint Locations

You must first display a table that contains data about the current locations that the hardpoints define.
You can then modify the hardpoint locations. You only need to indicate how you want to move the left
hardpoints in each pair, and Adams/Car modifies the right hardpoints accordingly.
To view hardpoint locations:

1. From the View menu, select Subsystem.
The Display Subsystem dialog box appears, already containing the subsystem
my_assembly.UAN_FRT_SUSP.
2. Select OK.
3. From the Adjust menu, point to Hardpoint, and then select Table.
The Hardpoint Modification Table appears. It displays the locations of all the hardpoints in the
assembly. You can use this table to display and modify the locations of any of the hardpoints.
The locations of the paired hardpoints differ only by the sign of the Y location. Therefore, the
paired hardpoints are symmetrical about the X-Z plane. With symmetrical hardpoints, you only
need to move one of the hardpoints, not both. If you want, however, you can break the symmetry
and move only one of the hardpoints of a symmetrical pair.
To see the symmetry, select left or right from the bottom of the Hardpoint Modification Table.
To modify the hardpoints:

1. Click the cell common to hpl_lca_outer and loc_y.
2. Change the existing value to -775. This moves the hardpoint point 25 mm outboard.
51
3. Scroll the table window down until you see the hardpoint hpl_uca_outer.
4. Click the cell common to hpl_uca_outer and loc_y.
5. Change the existing value to -700. This moves the hardpoint 25 mm outboard.
6. Select Apply.
Adams/Car changes the hardpoint locations of the two hardpoints and their symmetrical right
pairs.
7. Close the dialog box.
Saving the Modified Subsystem

In this section, you save the subsystem you just modified.
To save the subsystem:

1. From the File menu, select Save.
Before saving the file, Adams/Car asks you if you want to create a backup copy of the file.
2. Select No. This overwrites the subsystem file in your default writable database.
Adams/Car saves the subsystem file that you created.
Performing an Analysis on the Modified Assembly

To determine how the modifications to the suspension subsystem changed the pull on the steering wheel,
you perform a pull analysis on the modified suspension and steering assembly. You can use the same
loadcase file that you created in Defining a Loadcase File.

1. From the Simulate menu, point to Suspension Analysis, and then select External Files.
The dialog box displays the appropriate loadcase file.
2. In the Output Prefix text box, enter modified.
3. Select the Comment tool.
4. In the Comment Text text box, enter Steering axis moved 25mm outboard.
5. Select OK.
6. Select OK again.
Adams/Car analyzes the modified suspension and steering assembly.
53
Comparing the Analysis Results

You now create a plot that compares the analysis results from the baseline suspension and steering
assembly with the analysis results from the modified suspension and steering assembly.
To compare the analysis results:

1. Launch Adams/PostProcessor.
3. In the Plot Configuration File text box, enter mdids://private/plot_configs.tbl/brake_pull.plt.
4. In the Plot Title text box, enter Brake Pull Analysis - UAN_FRT_SUSP.
5. To plot the results of the two analyses on one page, select Cross Plotting.
6. Select OK.
7. Use the plot navigation tools to cycle through the plots.
8. Focus on the plot of the Steering Wheel Torque vs Steering Wheel Angle, shown in the following
figure. It contains values for both the baseline and the modified suspension and steering
assembly. Notice that the pull is reduced for all steering wheel angles, as expected.
Figure 8 Comparison Plot for Steering Wheel Torque vs Steering Wheel Angle
9. Cycle through the plots until you see a plot of the Scrub Radius vs Steering Wheel Angle, shown
below. This plot also contains values for both the baseline and the modified suspension and
steering assembly. Notice that the scrub radius decreased from 34 mm to 8 mm because of the
suspension modifications.
Figure 9 Comparison Plot for Scrub Radius versus Steering Wheel Angle
55
Finishing Up
Before you continue with the full-vehicle tutorial in the next chapter, you should clean up your directory
by deleting the plots and simulations, and closing the subsystems that you created and modified.
• Deleting Simulations
• Closing Assemblies
Deleting Simulations
You first delete the simulations for the baseline and modified analyses and then you return to the
Adams/Car main window.
To delete simulations:
1. Right-click the treeview, point to Type Filter, point to Modeling, and then select Analyses.
2. To show the current simulations, double-click my_assembly.
The treeview updates and displays the current simulations.
3. Select the simulations you want to delete.
4. From the Edit menu, select Delete.
Adams/Car deletes the simulations.
5. From the File menu, select Close Plot Window.
Closing Assemblies
You can now close the suspension and steering assembly.
To close the assembly:

1. From the File menu, point to Close, and then select Assembly.
The Close Assembly dialog box appears. By default it contains the name of your assembly.
2. Select OK.
57
Flexible Bodies Tutorial

Overview
In this tutorial, you run analyses on suspension and full-vehicle assemblies to see the effects of flexible
bodies.
Before you work through this tutorial, make sure you have:
• Adams/Flex.
• Completed the tutorial we’ve provided with Adams/Flex in the guide, Getting Started Using
Adams/Flex.
• A moderate level of finite element modeling proficiency.

• About Modal Flexibility in Adams/Car
• Working with Flexible Bodies in Suspension Assemblies
• Working with Flexible Bodies in Full-Vehicle Assemblies

59
About Modal Flexibility in Adams/Car

Adams/Car integrates and fully supports the Adams/Flex plug-in. Adams/Flex allows you to build
flexible bodies into your templates using a modes method, called modal flexibility. It assigns a set of
mode shapes (or eigenvectors) to a flexible body. The flexible body modeling element designates a
system state variable to each eigenvector and calculates the relative amplitude during a time analysis.
The principle of linear superposition is then used to combine the mode shapes at each time step to
reproduce the total deformation of the flexible body.
The following sections further explain flexible bodies:
• About Integrating Flexible Bodies
• About Flexible Body Damping Ratio
About Integrating Flexible Bodies

Integrating flexible bodies into templates or subsystems lets you capture inertial and compliance effects
during handling and comfort simulations, study deformations of your flexible components, and predict
loads with greater accuracy, therefore achieving more realistic results. Once the flexible body is created,
Adams/Car displays its geometric representation in the main window.
The flexible body characteristics are defined in a finite element modeling (FEM) output file, called
modal neutral file or MNF. The information in an MNF includes:
• Geometry (location of nodes and node connectivity)
• Nodal mass and inertia
• Mode shapes
• Generalized mass and stiffness for modal shapes
When you integrate a flexible body into a template, you have to supply the following:
• A modal neutral file. This means that the MNF should have been previously created and stored
in a shared or private database.
• Location and orientation information for the part that you will create. Adams/Car uses the
location and orientation information to rigidly rotate and translate the flexible body.
• Inertia coupling and the damping ratio.
You can now integrate flexible bodies into your subsystems or assemblies. The process of swapping rigid
bodies with flexible bodies is fast, easy, and convenient, it eliminates the need for multiple templates,
and is fairly automatic. With rigid-to-flexible swapping, modal flexibility becomes a property of the
body. When you integrate a flexible body into a subsystem, you must:
• Supply a modal neutral file. This means that the MNF should have been previously created and
stored in a shared or private database.
• Position the flexible body with respect to the rigid parts. For help, from the Adjust menu, point
to General Part, select Rigid to Flex, and then press F1.
• Monitor the connectivity. For help, from the Adjust menu, point to General Part, select Rigid to
Flex, and then press F1.
To successfully integrate a flexible body into an Adams/Car template or subsystem and run simulations,
consider these precautions:
• Use flexible bodies if a component flexibility affects the dynamic behavior of your model or if
you are interested in accurate deformations of the flexible body under various load conditions.
• Because flexible body deformations are a linear combination of deformation shapes, be careful
when modeling components undergoing high nonlinear deformations.
• Consider the computational load that a flexible body representation demands, especially if the
MNF description is very detailed, that is, if several modes have been included.
• Verify your flexible body and check the natural frequencies associated with the significant mode
shapes and the mass and inertia properties.
About Flexible Body Damping Ratio

Dynamic system simulations are greatly complicated when the time integration must traverse a signal
with very high frequency components. To achieve the desired accuracy, Adams/Solver must integrate the
signal with a possibly prohibitively short time step. Flexible bodies can contribute large amounts of high
frequency content and can, therefore, be difficult to simulate.
Carefully applying modal damping can help you successfully simulate a model containing flexible
bodies.You can specify a single scalar damping value applied to all the modes, control the damping using
a DMPSUB user-written subroutine, or accept the default nonzero damping that Adams/Flex applies to all
the modes.
If you do not specify the damping, Adams/Flex applies the following defaults:
• 1% damping for all modes with frequency lower than 100 Hz.
• 10% damping for modes with frequency between 100 and 1000 Hz.
• 100% critical damping for modes with a frequency higher than 1000 Hz.
During simulations, Adams/Car displays in the Message Window the type of damping that you selected
for each flexible body in the model.
We suggest that in this tutorial you work with the default damping ratio.
61

This tutorial guides you through the following steps:
• Creating, investigating, and successfully using flexible bodies in Adams/Car templates.
• Importing MNFs into existing subsystems to create models with flexible bodies.
• Modifying flexible body properties by changing the modal contents, the inertia coupling, and the
damping ratio.
• Modifying and analyzing a complete double-wishbone front suspension with flexible bodies.
• Creating a full-vehicle assembly, analyzing it, and viewing the results.
Working with Flexible Bodies in Suspension

Assemblies
In this section, you create a suspension assembly containing flexible lower control arms, learn how to
manage the flexible bodies in the assembly, and run an analysis and view its results. You compare the
difference in longitudinal wheel displacement by changing the left lower control arm to behave as a rigid
body. A flexible body behaves as a rigid body when you set the inertial invariants to rigid.
The following sections teach you how to work with flexible bodies in a suspension assembly:
• Creating a Suspension Assembly
• Managing Flexible Bodies
• Performing a Suspension Analysis
• Animating Analysis Results
• Plotting Analysis Results
• Closing Suspension Assemblies
Creating a Suspension Assembly

You start out by creating a double-wishbone front suspension assembly. This assembly is based on the
_double_wishbone template. After opening a suspension assembly, you introduce flexible bodies by
performing a rigid-to-flex swap operation.
To create a suspension assembly:

3. In the Assembly Name text box, enter susp_assy.

4. Right-click the Suspension Subsystem text box, point to Search, and then select the
acar_shared database.
5. Double-click TR_Front_Suspension.sub.
Notice that by default Adams/Car includes a suspension test rig in the assembly.
6. Select OK.
Adams/Car displays the assembly (note that we turned the shading on):
Figure 10 Double-Wishbone Suspension Assembly

63
Left/right lower control arm

rigid parts
Introducing Flexible Bodies

You use the rigid-to-flexible swap functionality to introduce flexible lower control arms to your
suspension assembly. Note that you are working on the subsystem (in previous versions, creating flexible
bodies meant that you had to create a new template, causing unnecessary template duplication).
To swap the rigid LCA with a flexible body:

1. Right-click ger_lower_control_arm, point to its name, and then select Modify.
2. Select Rigid to Flex.
3. Right-click the text box to the right of MNF File, and search the shared database for
LCA_right_shl.mnf.
Adams/Car creates a flexible body.
You don’t need to modify the location and orientation of the flexible body, because the MNF was
generated using a coordinate system coincident with the rigid part reference frame.
4. Select the Connections tab.

Adams/Car fills in the table with all the markers belonging to the rigid part. All the markers will
be reassigned (by default) to the closest available node. You can select individual markers by
highlighting the row and changing the connection properties.
5. Select the Move column, and then select Preserve expression.
All markers will now maintain their location and orientation parametric expressions.
6. Select OK.
Note: A warning message informs you that orientation parameterization references the old rigid
body, so parameterization will be lost. You can ignore this message.
Adams/Car deactivates the rigid body and replaces it with the corresponding flexible body.
7. Select OK in the Modify General Part dialog box.
8. Repeat the steps in this procedure for the left part, gel_lower_control_arm, making sure that you
select the MNF file named LCA_left_shl.mnf.
Managing Flexible Bodies

Managing flexible bodies involves verifying, modifying, and efficiently using flexible bodies. You can
rigidly rotate and translate flexible bodies, reposition them relative to the rest of the subsystem, as well
as change flexible body properties.
• Displaying Information About Flexible Bodies
• Displaying and Animating Modes
• Changing Flexible Body Inertia Modeling
Displaying Information About Flexible Bodies

You can see if Adams/Car correctly imported the flexible body into the template on which the suspension
subsystem is based, verify if the rigid-to-flex swap successfully placed the flexible body in the correct
location, and display information about the properties that define the flexible body.
To display information about a flexible body:

1. Right-click the left lower control arm flexible part, point to Flexible_Body:
TR_Front_Suspension.gel_lower_control_arm_flex, and then select Info.
The Information window appears as shown in the figure below. It lists the inertia properties, the
modal contents, and the name of the MNF that Adams/Car used when creating the flexible body.
The Information window also shows how many modes are active for that flexible body. Every
mode has a corresponding frequency, allowing you to verify that the frequencies that Adams/Car
displays are correct.
Figure 11 Information Window

65
2. Select Close.
Displaying and Animating Modes

You can also verify flexible bodies by displaying and animating the modes, and viewing the
corresponding frequencies. The Mode Manager is a powerful tool that lets you define a scale factor to
emphasize the deformation of the flexible body, animate the flexible part, modify its modal content to
improve the efficiency of the simulation, and set initial conditions.
The MNF, as explained in the above sections, contains information about modes and frequencies that
define the flexible body.
To view and animate modes:

1. From the Adjust menu, point to General Part, and then select Modify.
2. Right-click the General Part text box, point to Body, point to Pick, and from the screen, select
the left lower control arm, gel_lower_control_arm_flex.
3. Select the Mode Manager tool .
4. In the Mode Number text box, enter 9, and then press Enter.
In the Frequency text box, Adams/Car displays the frequency corresponding to mode 9. In the
main window, note the bending of the flexible lower arm occurring at approximately 345 HZ.
5. Select Superimpose.
6. Set Plot Type to Contour.
Adams/Car highlights the flexible body deformation using color contours (note that we changed
the color of the underformed flexible body to red).
7. Select the Animate tool .

Adams/Car animates the bending mode that the flexible body undergoes at 345 HZ.
Leave the dialog box open, because you will use it again in the next section.
67
Changing Flexible Body Inertia Modeling

To be able to compare the suspension characteristics between the flexible right and the rigid left side,
you change the inertia modeling of the left lower control arm.
Adams/Flex computes the time-varying mass matrix of the flexible body using nine inertia invariants. In
particular, four invariant formulations have special significance.
For more information about the invariant formulations, see the Adams/Flex online help.
To change the inertia modeling:

1. Set Inertia modeling to Rigid body.
2. Select OK.
3. Close the Modify Flexible Body dialog box.
Adams/Car disables the 6th invariant, modal mass, and the flexible body becomes equivalent to
a rigid part. This causes all the modes to be ignored during the simulation.
Performing a Suspension Analysis

To simulate the flexible body subsystem, you run a suspension analysis and then you review the results,
focusing on the flexible body characteristics.
To perform a static load analysis on the suspension subsystem, you define upper and lower braking forces
applied at the hub.
To perform a static load analysis:

1. From the Simulate menu, point to Suspension Analysis, and then select Static Load.
Adams/Car performs the analysis and displays messages about the simulation. The static load
analysis simulates the front suspension during a braking maneuver. The change in brake forces
causes a longitudinal wheel displacement.
69
Animating Analysis Results

You animate the results of the analysis to view the deformation of the left rigid arm compared to the right
flexible arm. During the animation, Adams/Car applies a longitudinal force at the hub.

Adams/Car animates the suspension.
Plotting Analysis Results

The flexibility of the right lower control arm affects a series of suspension characteristics that Adams/Car
computes automatically. You can review the results of these calculations in the plotting environment.
Adams/Car automatically loads the request file containing the suspension characteristics. Also, when a
flexible body is included in a suspension or in a vehicle assembly, Adams/Car loads the result file
produced during the analysis. The result file contains information about the flexible body, as well as any
other Adams/Solver outputs.

1. Launch Adams/PostProcessor just as you did in Comparing the Analysis Results.
3. From the Simulation list, select tst1_static_load (Adams/Car Assembly).
4. From the Request list, select wheel_travel_base.
Note: Requests are hierarchically arranged under their respective models. You can find
wheel_travel_base under the testrig entry. Double-click the plus sign (+) in
front of testrig to expand the entry.
5. From the Component list, select base_left.

6. Set Independent Axis to Data.
7. From the Request list, select wheel_load_longitudinal.
8. From the Component list, select braking_left.
9. Select OK.
11. Repeat Steps 4 through 10, this time selecting the right-side components for wheel_travel_base
and wheel_load_longitudinal.
Adams/Car plots the longitudinal compliance for the left and right side versus the right
longitudinal force at the contact patch.
The plot shows the effect of the flexible body on the displacement of the wheel center due to a
longitudinal braking force.
Figure 12 Wheel Center Longitudinal Displacement versus Longitudinal Force
12. Return to Adams/Car.
Closing Suspension Assemblies

Before you continue with the full-vehicle analysis, close the suspension assembly.
To close a subsystem assembly:

1. From the File menu, point to Close, and then select Assembly.
2. Select OK.
71
Working with Flexible Bodies in Full-Vehicle

Assemblies
In this section, you perform a full-vehicle maneuver and focus on the flexible part characteristics. Before
you can perform the maneuver, you must create a full-vehicle assembly and set the suspension subsystem
in kinematic mode.
You perform these operations in the following sections:
• Creating a Full-Vehicle Assembly
• Defining the Kinematic Mode
• Setting Up the Analysis
• Performing a Full-Vehicle Analysis
• Plotting Analysis Results
Creating a Full-Vehicle Assembly

To create the assembly:
1. From the File menu, point to New, and then select Full-Vehicle Assembly.
Adams/Car displays the full-vehicle assembly, as shown next:

73
Defining the Kinematic Mode

To eliminate the compliance contributions of the attachment bushings to the subsystem, you must set the
suspension subsystem to kinematic mode. The only elastic components will be the flexible lower control
arms.
To define the kinematic mode:

1. From the View menu, select Subsystem.
The Display Subsystem dialog box appears, containing
fveh_assy.TR_Front_Suspension_flex as the default subsystem.
2. Select OK.
Adams/Car displays the suspension subsystem.
3. From the Adjust menu, select Kinematic Toggle.
4. Set Current Mode to Kinematic.
5. Select OK.
Setting Up the Analysis

You are now ready to submit the full-vehicle analysis. However, to become more familiar with
Adams/Car, we recommend that you first perform the following tasks:
• Swapping MNFs
• Modify the integrator parameter
• Deactivate modes
In this section you perform the following tasks:

• Swapping MNFs
• Changing Modal Content
Swapping MNFs
If the FEM expert produced the lower control arm modal neutral files maintaining the same node number
for the attachment points, you can easily swap the flexible body (modal neutral files) and maintain the
parameterization. You can replace the flexible body by selecting a different MNF provided in the shared
database. This is analogous to replacing a damper or spring property file.
To swap the MNF:

1. Double-click the left flexible lower control arm, fbl_lower_control_arm.
The Modify Flexible Body dialog box appears.
2. Right-click the Modal Neutral File text box, point to Search, and then select the acar_shared
database.
3. Double-click LCA_left_tra.mnf.
4. Select Apply.
5. Right-click the Flexible Body text box, point to Flexible Body, point to Pick, and from the
screen, select the right lower control arm, fbr_lower_control_arm.
6. In the Modal Neutral File text box, enter LCA_right_tra.mnf.
7. Select OK.
Adams/Car replaces the flexible lower control arm that was originally modeled using shell
elements in the FEM environment, with beam elements. Moreover, the lca_front hardpoint
now has a different location, but Adams/Car has maintained the parameterization of the model,
and the topological information is correct. This is because Adams/Car uses interface parts to
connect flexible bodies with the rest of the model. Interface parts are a special class of general
parts that are parameterized to the locations of the node numbers. When the locations of the node
numbers move, the interface parts and the rest of the model move accordingly. Node numbers are
defined in the MNF and cannot be changed in Adams/Car.
75
Figure 13 Modified Flexible Lower Control Arm
8. To return to the full-vehicle assembly, from the View menu, select Assembly.
9. Select OK.
Changing Modal Content

By default, when you integrate an MNF into an Adams/Car template, Adams/Flex enables all the modes
that were defined during the FEM modeling except the probable rigid body modes. It is important to have
the right modal content in flexible bodies, because an MNF has more modes than are needed to simulate
a particular response.
To increase the efficiency of the simulations, you should disable any modes that do not contribute to the
motion that your flexible part will undergo during the simulation. Be careful when disabling modes,
because a disabled mode corresponds to a constraint to the part. Changing the modal content of a flexible
body corresponds to a flexible body setup.
You can manually toggle modes on or off. This gives you greater flexibility and helps you avoid potential
problems. You can enable and disable modes in several ways:
• Individually, based on their mode number.
• As a group, based on their mode number or frequency.
• Through a table editor. The table editor also lets you define displacement and velocity initial
conditions associated with every mode.
• Based on their strain energy contribution, but you can only do this after a successful analysis.
For more information on this technique, see the Adams/Flex online help.
To disable individual modes:

Some of the modes of the flexible lower control arms do not contribute effectively to the dynamic
behavior of the entire system. We recommend that you disable them to reduce the computational effort
and to improve the efficiency of the simulation.
You must disable these modes for both the left and the right side because a left and a right MNF defines
the flexible lower control arms.
1. Zoom in on the front suspension.
2. From the Adjust menu, point to Flexible body, and then select Mode Manager.
The Flexible Body Modify dialog box appears.
3. Right-click the Flexible Body text box, point to Flexible body, point to Pick, and from the screen,
select the left lower control arm, fbl_lower_control_arm.
4. Select Modal ICs.
The Modify Modal ICs dialog box appears.
5. Hold down the Shift key, select modes 28 and 29, and then select Disable Highlighted Modes.
6. Close the Modify Modal ICs dialog box.
7. Repeat Steps 3 through 6, for the right lower control arm, fbr_lower_control_arm.
8. Close the Flexible Body Modify dialog box.
Performing a Full-Vehicle Analysis

You are now ready to perform the full-vehicle analysis. After you perform the analysis, you can change
the inertia modeling of the flexible body to compare the effect of the modal flexibility on the dynamics
of the vehicle.
77
To perform the full-vehicle analysis:

1. From the Simulate menu, point to Full-Vehicle Analysis, point to Open-Loop Steering Events,
and then select Step Steer.
• Full-Vehicle Assembly: fveh_assy
• Output Prefix: tst
• End Time: 4
• Initial Velocity: 70 (take the default of km/hr)
• Gear Position: 3
• Initial Steer Value: 0
• Final Steer Value: -45
• Step Start Time:1
• Duration of Step: 1
• Steering Input: Angle
3. Keep the defaults for Cruise Control (off) and Quasi-Static Straight Line Setup (on).
4. Select Apply, so the dialog box stays open for the analysis you will run in the next section.
The SDI test rig applies to the assembly the inputs you specified and performs a dynamic analysis.
To change the inertia modeling:

1. Double-click the left lower control arm, fbl_lower_control_arm.
2. Select the Mode Manager tool.
3. Set Inertia modeling to Rigid body.
4. Select OK.
5. Close the Modify Flexible Body dialog box.
6. Submit another step steer analysis using the same inputs as before, but changing the output prefix
to tst_rigid.
Adams/Car analyzes the assembly.
Plotting Analysis Results

In this section, you create a set of plots that show the behavior of your vehicle assembly and then review
how the modal flexibility of the lower control arm affects the overall dynamics of the vehicle.


Figures 15 and 16 show some of the plots. The flexible lower control arms cause the differences
between the curves.
4. View the plots shown next and then return to Adams/Car.
Figure 14 Lateral Slip Angle

79
Figure 15 Yaw Rate

77
Template Builder Tutorial

This tutorial guides you through the process of building a template, creating a suspension subsystem
based on the template, and then running various analyses on the subsystem. To build the template, you
must use Adams/Car Template Builder.
• Creating Topology for Your Template
• Creating a Suspension Subsystem
• Analyzing an Assembly Containing Your Template
This tutorial takes about two hours to complete.


To learn how to create templates, you create a complete MacPherson front suspension template, as shown
in Figure 16 (note that we toggled the icon visibility off and the shading on). You then build a suspension
using the template you created. Finally, you run kinematic and compliant suspension analyses and
compare their results.
Figure 16 MacPherson Front Suspension Template
Damper
Spring
Tie rod
Wheel
Carrier
Hub
Control arm
Attachment
bushing
79
Creating Topology for Your Template

Before you begin to build your template, you must decide what elements are most appropriate for your
model. You must also decide which geometries seem most applicable to each part or whether you want
any geometry at all. Once you’ve decided, you create a template and create the basic topology for it.
Finally, you assemble the model for analysis.
This section involves the following steps:
• Creating a Template
• Building Suspension Parts
• Creating and Defining Attachments and Parameters
• Assembling the Model for Analysis
• Finishing Up
Creating a Template
You must create a template in which to build suspension parts. You should assign to your template a
major role as a suspension template, because a major role defines the function the template serves for the
vehicle.
To create a template:
1. Start Adams/Car Template Builder as explained in Starting Adams/Car Template Builder.
2. From the File menu, select New.
3. In the Template Name text box, enter macpherson.

4. Verify that Major Role is set to suspension.
5. Select OK.
A gravity icon appears in the middle of the Adams/Car main window as shown in the following
figure. If you don’t see a gravity icon, display the main shortcut menu by right-clicking the main
window, and selecting Toggle Icon Visibility. You can also toggle the icon visibility on and off
by placing the cursor in the main window and typing a lowercase v.
6. From the main shortcut menu, select Front Iso and Fit - All. Fit your model to view whenever
you create an entity outside the current view.
The Adams/Car main window should look as follows:
Figure 17 Main Window with Gravity Icon Displayed

Building Suspension Parts

You create parts in Adams/Car through a three-step process. First, you create hardpoints that define key
locations on the part. Then, you create the actual part. Finally, if you want, you add geometry to your new
part.
You can use one of two methods to create parts in Adams/Car:
• User-entered method lets you manually enter mass properties and material type for a part.
81
• Geometry-based method lets you tell Adams/Car to automatically create mass properties using
the geometry and material type that you specify.
In the next sections, you create all the parts that make up the suspension template:
• Creating the Control Arm
• Creating the Wheel Carrier
• Creating the Strut
• Creating the Tie Rod
• Creating the Toe and Camber Variables
• Creating the Hub
Creating the Control Arm

The first part you define is the control arm. You begin by building its hardpoints. You can later modify
these hardpoints to determine their effects on your vehicle.
Next, you create the control arm part and specify its coordinate system location and mass properties.
To complete the creation of the control arm, you create geometry for it. You then define key locations
for that geometry so Adams/Car can calculate its mass properties. In this tutorial, whenever you want
Adams/Car to calculate mass properties, you select steel as the material type.
When specifying orientations in Adams/Car, you can either enter Euler angles or specify two direction
vectors. In this tutorial, you will just use Euler angles with respect to the global orientation marker, which
is named origo.
To build the hardpoints:

1. From the Build menu, point to Hardpoint, and then select New.
2. In the Hardpoint Name text box, enter arm_outer.
3. Verify that Type is set to left.
In this tutorial, you set all entities to left. Adams/Car automatically creates a symmetrical pair
about the central longitudinal axis.
Note: Depending on how you set up your environment variables, the longitudinal axis can be any
axis. In this tutorial, the longitudinal axis is the x-axis. For information on setting your
environment variables, see the Adams/Car online help.
4. In the Location text box, enter 0, -700, 0.

5. Select Apply.
6. Adams/Car creates the hardpoint, but leaves the Create Hardpoint dialog box open.
7. Repeat Steps 2 through 5 to build the two hardpoints specified in Table 2.
Hardpoint Name: Location:

arm_front -150, -350, 0
arm_rear 150, -350, 0
8. When you’re done creating the hardpoints, close the dialog box.
9. To see all six hardpoints in the main window, fit your model to view (type a lowercase f).
To create the control arm part:

1. From the Build menu, point to Parts, point to General Part, and then select New.
83
Adams/Car creates a part coordinate system, also referred to as local part reference frame (LPRF,
which is also known as the Body Coordinate System (BCS)), at the specified location, but it
doesn’t create geometry.
To create the control arm geometry:

1. From the Build menu, point to Geometry, point to Arm, and then select New.
2. Create the control arm as follows:
• Arm Name: control_arm

• General Part: ._macpherson.gel_control_arm
• Coordinate Reference #1: ._macpherson.ground.hpl_arm_outer
• Coordinate Reference #2: ._macpherson.ground.hpl_arm_front
• Coordinate Reference #3: ._macpherson.ground.hpl_arm_rear
• Thickness: 10
3. Select Calculate Mass Properties of General Part.
4. Set Density to Material.
5. Select OK.
Adams/Car displays the control arm part. If you want the control arm to be shaded, put the cursor
in the main window and type an uppercase S. This toggles the rendering mode between shaded
and wireframe.
Note: Based on the geometry, the option Calculate Mass Properties of General Part computes the
mass properties for the part, and adds that to the total mass of the part. (You can have more
than one geometry associated with a part.) Also, note that the mass of the part is not
parameterized to its geometry. Therefore, if you want to base the mass of the part on new
geometry, you must use the Calculate Mass functionality for the part.
Creating the Wheel Carrier

To create the wheel carrier, you must first create three hardpoints that define the location of the wheel
carrier. You then define the wheel carrier part using these hardpoint locations.
Next, you add link geometry to the wheel carrier. When you add the link geometry, you enter parameters
that are similar to those you specified for the arm geometry, except that a link only requires two
coordinate reference points to define its geometry.
To create the hardpoints:

1. From the Build menu, point to Hardpoint, and then select New.
2. Create the wheel carrier hardpoints as specified in Table 1. Remember that you can select Apply
to execute the command but leave the dialog box open, and select OK to execute the command
and then close the dialog box.
Table 1 Wheel carrier hard points

Hardpoint Name: Location:
wheel_center 0, -800, 100
strut_lower 0, -650, 250
tierod_outer 150, -650, 250
85
3. To display the hardpoints in the main window, fit your model to view.
Note: Remember that all these hardpoints are left-side hardpoints.
To create the wheel carrier part:

1. From the Build menu, point to Parts, point to General Part, and then select Wizard.
2. Create the wheel carrier part as follows:
• General Part Name: wheel_carrier
• Geometry Type: Arm
• Coordinate Reference #1: ._macpherson.ground.hpl_wheel_center
• Coordinate Reference #2: ._macpherson.ground.hpl_arm_outer
• Coordinate Reference #3: ._macpherson.ground.hpl_strut_lower
• Thickness: 10
3. Select OK.
The wizard creates both the part and the geometry.
To add the wheel carrier link geometry:

1. From the Build menu, point to Geometry, point to Link, and then select New.
2. Create the wheel carrier part as follows:
• Link Name: carrier_link
• General Part: ._macpherson.gel_wheel_carrier
• Coordinate Reference #2: ._macpherson.ground.hpl_tierod_outer
• Radius: 10
4. Select OK.
The template now includes the wheel carrier part and the link geometry.
Creating the Strut

In this section, you create the strut part for your suspension template. Just as you did for the control arm,
you enter the location, orientation, and mass properties for the strut part.
Because the strut geometry would not be visible from inside the damper, you don’t need to give the strut
any geometry.
To define the strut part:

2. Define the strut part as follows:

• General Part: strut
• Location values: 0, -600, 600
• Euler Angles: 0, 0, 0
• Mass/Ixx/Iyy/Izz: 1
3. Select OK.
Creating the Tie Rod

You first create a hardpoint and then use it to define the tie rod part.
To create a hardpoint:
1. Create a hardpoint with the following specifications:
• Hardpoint Name: tierod_inner
• Location: 200, -350, 250
2. Select OK.
To create the tie rod part:

1. From the Build menu, point to Parts, point to General Part, and then select Wizard.
2. Create the tie rod part as follows:
• General Part Name: tierod
• Geometry Type: Link
• Coordinate Reference #1: ._macpherson.ground.hpl_tierod_outer
• Coordinate Reference #2: ._macpherson.ground.hpl_tierod_inner
• Radius: 10
3. Select OK.
The template now includes the tie rod part.
Creating the Toe and Camber Variables

You create variables defining toe and camber angles. Because these variables are commonly used for
suspension analyses, Adams/Car creates both of them in one step.
To create toe and camber variables:

1. From the Build menu, point to Suspension Parameters, point to Toe/Camber Values, and then
select Set.
87
Note: When Adams/Car creates the toe and camber values, it also creates output communicators
of the same name. For details on communicators, see Assembling the Model for Analysis.
Creating the Hub

Before you create the hub part for your template, you must create a construction frame. Construction
frames are Adams/Car elements that you use whenever an entity requires that you specify an orientation
in addition to a location.
You create the hub based on the construction frame, and then create geometry for the hub.
To create a construction frame:

1. From the Build menu, point to Construction Frame, and then select New.
2. Create a construction frame as follows:
• Construction Frame: hub_bearing
• Location Dependency:Delta location from coordinate
• Coordinate Reference: ._macpherson.ground.hpl_wheel_center
• Orientation Dependency: Toe/Camber
• Toe Parameter Variable: ._macpherson.pvl_toe_angle
• Camber Parameter Variable: ._macpherson.pvl_camber_angle
3. Select OK.
To create the hub part:

2. Create the hub part as follows:
• General Part: hub
• Location Dependency:Delta location from coordinate
• Coordinate Reference: cfl_hub_bearing
• Location values: 0, 0, 0
• Orientation Dependency: Delta orientation from coordinate
• Construction Frame: cfl_hub_bearing

• Orientation: 0, 0, 0
• Mass/Ixx/Iyy/Izz: 1
3. Select OK.
To create cylinder geometry for the hub:

1. From the Build menu, point to Geometry, point to Cylinder, and then select New.
2. Create the cylinder geometry as follows:
• Cylinder Name: hub
• General Part: ._macpherson.gel_hub
• Construction Frame: ._macpherson.ground.cfl_hub_bearing
• Radius: 30
• Length in Positive Z: 30
• Length in Negative Z: 0
• Color: magenta
4. Select OK.
The template now includes the hub.
Creating Forces
In this section, you create a damper and a spring.
Creating the Damper

You first create a hardpoint and then use it to define the damper. You then create a damper that is defined
by a property file that we provide for you. Property files define force-displacement, force-velocity, and
other kinds of characteristics for springs, dampers, bumpstops, reboundstops, and bushings. In this case,
the property file defines the damper’s force-velocity curve.
To create a hardpoint:
1. Create a hardpoint as follows:
• Hardpoint Name: strut_upper
• Location: 0, -600, 600
2. Select OK.
To create the damper:

1. From the Build menu, point to Forces, point to Damper, and then select New.
89
2. Create the damper as follows:

• Damper Name: damper
• I Part: ._macpherson.gel_wheel_carrier
• J Part: ._macpherson.gel_strut
• I Coordinate Reference: ._macpherson.ground.hpl_strut_lower
• J Coordinate Reference: ._macpherson.ground.hpl_strut_upper
3. Select OK.
Defining the Spring

Before you define the spring, you have to create a hardpoint that defines the position of the lower spring
seat. Then, to define the spring, you must specify the following:
• Two bodies between which you want the force to act.
• Specific location on each body where you want the force to act.
• Installed length of the spring, which will be used to derive the design preload on the spring.
• Property file, which contains the free length information, as well as the force/deflection
characteristics.
Adams/Car calculates the force exerted by the spring using the following equations:
C = FL - IL + DM’(i,j)
Force = -k(C - DM(i,j))
where:
• C is a constant.
• FL is the free length of the spring, as defined in the property file.
• IL is the defined installed length.
• DM(i,j) is the change in the displacement between the i and j coordinate reference points as the
simulation progresses.
• DM’(i,j) is the initial displacement between the i and j coordinate reference points. If you enter a
smaller value for DM(i,j), Adams/Car calculates an increased preload for the spring. Conversely,
if you enter a larger value, Adams/Car calculates a decreased preload. In this tutorial, you enter
the value that Adams/Car automatically calculates for you.
• Force represents the spring force.
• k is the nonlinear spring stiffness derived from the property file.
To create a hardpoint for the spring:

1. Create a hardpoint as follows:
• Hardpoint Name: spring_lower
• Location: 0, -650, 300
2. Select OK.
To create the spring:

1. From the Build menu, point to Forces, point to Spring, and then select New.
To enter this value automatically,

select DM(iCoord, jCoord) and
then select Fill Field.
The template now includes the damper and the spring.

91
Creating and Defining Attachments and Parameters

Now that you created all the Adams/Car parts, springs, and dampers, you are ready to define attachments
and parameters.
This section includes the following:
• Defining the Translational Joint
• Defining Control Arm Attachments
• Defining the Strut Attachment
• Defining Wheel Carrier Attachments
• Defining Hub Attachments
• Defining Suspension Parameters
Defining the Translational Joint

You first create a translational joint between the wheel carrier and the strut. You specify that this joint is
active regardless of the mode in which you simulate your model.
In Adams/Car, you can simulate your model in kinematic or compliant mode. A kinematic analysis uses
constraints, such as translational and revolute joints, to define the attachments between the parts. During
a compliant analysis, Adams/Car replaces these joints with bushings. The joint-bushing swap only
occurs if the joint and/or bushing has been defined to be active and/or inactive, respectively, when
defining the attachment.
To define a translational joint:

1. From the Build menu, point to Attachments, point to Joint, and then select New.
2. Create the translational joint as follows:
• Joint Name: strut_joint
• J Part: ._macpherson.gel_strut
• Joint Type: translational
• Coordinate Reference: ._macpherson.ground.hpl_strut_upper
• Orientation Dependency: Orient axis along line
• Coordinate Reference #2: ._macpherson.ground.hpl_strut_upper
3. Select OK.
Defining Control Arm Attachments

Before you create bushings and joints for the control arm, you must create the mount parts that act as
placeholders for the attachments. A mount part is a massless part that is fixed to ground. The purpose of
a mount part is to be replaced by another part (for example, vehicle body, subframe, wheel, and so on) if
its associated input communicator(s) find matching output communicator(s), or to be replaced by ground
if no matching output communicator is found.
When you create a mount part, Adams/Car automatically creates an input communicator for it of class
mount. The input communicator requests the name of the part to which the mount part should connect.
If Adams/Car finds a matching communicator during assembly, it replaces the mount part with the part
that the output communicator indicates. The replacement part is from another subsystem. If Adams/Car
finds no matching output communicator, it replaces the mount part with the ground part.
To create a mount part, you specify a hardpoint and mount part name. If the hardpoint has a left or right
symmetrical twin, Adams/Car creates left and right mount parts and input communicators. Otherwise, it
creates a single mount part and a single input communicator.
After you create the mount parts, you create bushings for the control arm. You specify the parameters,
such as preload and offset, that define bushings. In this example, you use the default values that
Adams/Car provides. If you want, you can modify the bushing properties. You also set its inactive status
to kinematic, so that during a kinematic analysis Adams/Car deactivates this bushing.
Finally, you create the control arm revolute joint. This time, you set its active status to kinematic. This
tells Adams/Car that during a kinematic analysis it should use the revolute joint, but it should replace the
joint with a bushing during a compliant analysis.
To create the mount parts:

1. From the Build menu, point to Parts, point to Mount, and then select New.
2. In the Mount Name text box, enter subframe_to_body.
3. In the Coordinate Reference text box, enter ._macpherson.ground.hpl_arm_front.
4. Verify that From Minor Role is set to inherit.
5. Select OK.
Adams/Car creates fixed joints between the mount parts and ground. By default, the visibility of
the fixed joints is turned off.
To create the front bushing for the control arm:

1. From the Build menu, point to Attachments, point to Bushing, and then select New.
2. Fill in the dialog box as shown next, and then select Apply.
93
Remember to select Apply so

the dialog box remains open
Adams/Car creates the front bushing and leaves the dialog box open so you can create the rear
bushing.
To create the rear bushing for the control arm:

1. In the Bushing Name text box, enter arm_rear.
2. In the Coordinate Reference text box, enter ._macpherson.ground.hpl_arm_rear.
3. Select OK.
Adams/Car creates the rear bushing.
To create the control arm revolute joint:

1. Create the control arm revolute joint as follows:
• Joint Name: arm_front
• I Part: ._macpherson.gel_control_arm
• J Part: ._macpherson.mtl_subframe_to_body
• Joint Type: revolute
• Active:kinematic mode
• Coordinate Reference: ._macpherson.ground.hpl_arm_front
• Orientation Dependency: Orient axis along line
• Coordinate Reference #1: ._macpherson.ground.hpl_arm_front
• Coordinate Reference #2: ._macpherson.ground.hpl_arm_rear
2. Select Apply.
To create the control arm spherical joint:

1. Create the control arm spherical joint as follows:
• Joint Name: arm_outer
• J Part: ._macpherson.gel_control_arm
• Joint Type: spherical
• Active:always
• Coordinate Reference: ._macpherson.ground.hpl_arm_outer
2. Select OK.
Defining the Strut Attachment

Before you define the strut attachments to the vehicle body, you must define a mount part for the strut.
You then create a bushing for the strut. Next, you create a spherical joint to replace the strut mount
bushing during kinematic analyses.
95
To define a mount part:

1. Create a mount part as follows:
• Mount Name: strut_to_body
• From Minor Role: inherit
2. Select OK.
To create a bushing for the strut:

1. Create the bushing as shown next, and then select OK.
97
To create a spherical joint for the strut:

1. Create the spherical joint as follows:
• Joint Name: strut_upper
• I Part: ._macpherson.gel_strut
• J Part: ._macpherson.mtl_strut_to_body
• Active:kinematic mode
2. Select Apply.
Defining Wheel Carrier Attachments

In this section, you define a spherical joint between the wheel carrier and the tie rod. You then define the
mount part that connects the suspension to the steering rack during assembly. Finally, you create a hooke
joint between the tie rod and the steering rack.
To create a spherical joint:

1. Create the spherical joint as follows:
• Joint Name: tierod_outer
• J Part: ._macpherson.gel_tierod
• Active:always
• Coordinate Reference: ._macpherson.ground.hpl_tierod_outer
2. Select OK.
To create a mount part for the hooke joint:

1. Create a mount part as follows:
• Mount Name: tierod_to_steering
• Coordinate Reference: ._macpherson.ground.hpl_tierod_inner
• From Minor Role: inherit
2. Select OK.
To create a hooke joint:

1. Create a hooke joint as follows:
• Joint Name: tierod_inner
• I Part: ._macpherson.gel_tierod
• J Part: ._macpherson.mtl_tierod_to_steering
• Joint Type: hooke
• Active: always
• Coordinate Reference: ._macpherson.ground.hpl_tierod_inner
• I-Part Axis:._macpherson.ground.hpl_tierod_outer
• J-Part Axis: ._macpherson.ground.hpr_tierod_inner
2. Select Apply.
Defining Hub Attachments

You can now define the hub bearing revolute joint between the wheel carrier and the hub.
To define the hub attachment:

1. Create a revolute joint as follows:
• Joint Name: hub_bearing
• J Part: ._macpherson.gel_hub
• Joint Type: revolute
• Active:always
• Coordinate Reference: ._macpherson.ground.hpl_wheel_center
• Orientation Dependency: Delta orientation from coordinate
• Construction Frame: ._macpherson.ground.cfl_hub_bearing
2. Select OK.
Defining Suspension Parameters

You create a steering axis using the geometric method for calculating steer axes. When using the
geometric method, Adams/Car calculates the steer axis by passing a line through two non-coincident
hardpoints located on the steer axis. To use the geometric method, you must identify the part(s) and two
hardpoints that fix the steer axis.
To create a steer axis:

1. From the Build menu, point to Suspension Parameters, point to Characteristic Array, and then
select Set.
99
Assembling the Model for Analysis

Adams/Car uses communicators to correctly assemble the model for analysis. Communicators are the
Adams/Car elements that allow the subsystems and test rigs to exchange information about the
following:
• Topological data, meaning information about parts and attachments.
• Array and parameter variables.
• Locations, orientations, and so on.
Every subsystem or test rig in Adams/Car has input communicators that need information from other
subsystems to function correctly in the model. Similarly, the corresponding subsystem or test rig, needs
to have a correctly named output communicator that will send it information. For example, an input
communicator needs information on the location of a hardpoint. A corresponding output communicator
provides the location information.
During the assembly process, Adams/Car scans the model for subsystems with minor roles. It then looks
through those subsystems for any input communicators that require information. It then tries to find an
output communicator, of the same entity type, with the same matching name. If it can’t find one, it won’t
match the communicators and the model may be incorrectly assembled.
For example, whenever you create a mount part in your template, Adams/Car automatically creates a
corresponding input communicator. During assembly, this input communicator should match the correct
output mount communicator located in the test rig. If Adams/Car finds no matching output
communicator, it replaces the mount part with the ground part.
Adams/Car automatically creates an input communicator corresponding to that mount on the test rig.
Then, you need to create a matching output communicator on the template you are creating. These
communicators must have the exact same name for Adams/Car to know which communicators to use.
This is explained in detail in Defining Communicators.
In this section, you create and verify output communicators:

• Defining Communicators
• Testing Communicators
Defining Communicators
For the assembly process to work correctly, you must define how the suspension is to connect to the
suspension test rig (_MDI_SUSPENSION_TESTRIG). To do this, you define the communicators that
attach the hub to the suspension test rig at the wheel center, as follows:
• To tell the suspension test rig to which part it needs to be connected, you define an output
communicator of type mount. This communicator accomplishes two tasks:
• Communicates the part to which the testrig is being connected.
• Defines the I part of the static lock actuator.
• To tell the suspension test rig where the connection takes place, you define an output
communicator of type location.
• To tell the suspension test rig which is the upright part (wheel carrier), to create a static lock
actuator, you define an output communicator of type mount. This communicators defines the J
part of the static lock actuator.
When you analyze the suspension in static mode, you must lock the hub to the wheel carrier. If you don’t
lock the hub to the wheel carrier, your assembly will have a rotational degree of freedom that prevents
the analysis from converging to a solution. Adams/Car creates the actuator between the hub and the
upright (wheel carrier), automatically based on the communicators mentioned above.
To display information about communicators:

1. From the Build menu, point to Communicator, and then select Info.
2. Clear the Model Names text box.
3. Right-click the Model Names text box, point to Model, point to Guesses, and then select
.__MDI_SUSPENSION_TESTRIG.
4. Select array, location, and mount.
5. Select OK.
The Information window appears as shown next:
101
The Information window lists the mount input communicators. Notice that Adams/Car
automatically adds the prefix ci[lr] (which designates communicator input left or right) to the
name of input communicators. If you want to see the entire contents of the Information window,
use the vertical scroll bar. If you want to see the matching name for each communicator, use the
horizontal scroll bar.
6. Select Close.
To create the output communicators:

1. From the Build menu, point to Communicator, point to Output, and then select New.
2. In the Output Communicator Name text box, enter suspension_mount.
3. Set Entity to mount.
4. Verify that To Minor Role is set to inherit.
5. In the Part Name text box, enter ._macpherson.gel_hub.
Note: Adams/Car allows you to specify one or more Matching Names so that you can
designate different communicators for the front and rear subsystems in case you might be
using the same template for both subsystems. In this case, you’ll just leave it blank since
Adams/Car defaults to assigning the communicator name as the matching name if none is
specified.
6. Select Apply.
Adams/Car selects the hub as the part to which the test rig connects.
7. In the Output Communicator Name text box, enter suspension_upright.
8. In the Part Name text box, enter ._macpherson.gel_wheel_carrier.
9. Select Apply.
10. In the Output Communicator Name text box, enter wheel_center.
11. Set Entity to location.
12. Verify that To Minor Role is set to inherit.
13. In the Coordinate Reference Name text box, enter ._macpherson.ground. hpl_wheel_center.
14. Select OK.
Adams/Car will use this location communicator to select the location on the hub to which the test
rig connects.
Testing Communicators
To verify that you correctly specified the input and output communicators, you can test communication
in your template. Testing your communicators lets you find out whether to add or modify communicators
to ensure that your suspension template will assemble properly with the suspension test rig.
To test the communicators:

1. From the Build menu, point to Communicator, and then select Test.
103
The Information window appears as shown next:

Note the symmetry

differences
The Information window lists which communicators are matched, and which are not. First, it
shows you the matched communicators that are correctly sending and receiving information
between subsystems and test rigs. Notice that the mount communicators for
suspension_mount, suspension_upright, and wheel_center are listed in the
matched communicator section.
105
The Information window also lists input and output communicators that are not matched
correctly. Many communicators are unmatched. Many of these communicators are related to
items such as the steering or chassis that we do not currently have open. When you start creating
your own templates, you can use the Information window to verify that you included all necessary
communicators.
3. Select Close.
Finishing Up
After you finish building the template, save it in your private database so you can use it later to create
suspension subsystems. Adams/Car assigns the extension .tpl to your template.
After you save your template, you can exit template-builder mode and start the Adams/Car Standard
Interface.
To save the suspension template:

To exit template-builder mode:

• From the Tools menu, select Adams/Car Standard Interface.
• Adams/Car returns to standard-interface mode, where you can create the suspension subsystem.
Creating a Suspension Subsystem

In this section, you create an Adams/Car suspension subsystem that is based on the template you just
built. You also modify some hardpoints and translate the subsystem to ensure that Adams/Car correctly
positions the subsystem within the assembly.
To create a subsystem:
1. From the File menu, point to New, and then select Subsystem.
You select the private

database because that is
where you saved the
suspension template
Adams/Car displays the following message:

The template _macpherson exists in memory. Do you want to use it?
3. Select Yes.
Adams/Car displays the subsystem.
To modify hardpoints:
1. From the Adjust menu, point to Hardpoint, and then select Table.
2. Modify the hardpoint values to match those listed in Table 2:
Table 2 Hardpoint table

Name: loc_x: loc_y: loc_z:
hpl_arm_front -200 -400 225
hpl_arm_rear 200 -390 240
hpl_tierod_inner 200 -400 300
hpl_tierod_outer 150 -690 300
107
3. Select Apply.
4. Select Cancel.
To save the subsystem:

Analyzing an Assembly Containing Your Template

In this section, you perform two types of suspension analyses and plot the results.
We assume that you already completed the previous tutorials, and know how to incorporate your new
template into an analysis.
You perform the following types of analyses:
• Performing a Kinematic Analysis
• Performing an Elasto-Kinematic Analysis
Performing a Kinematic Analysis

When you perform a kinematic analysis, you use the joints, rather than the bushings, that you defined
when you built your template.
Before you can perform the kinematic analysis, you must create a suspension assembly. After you create
the suspension assembly, define a preload.
To create a suspension assembly:

2. In the Assembly Name text box, enter susp_assy_1.
3. Verify that Suspension Subsystem is set to the name of your subsystem, my_macpherson. If it
is not, click the folder icon next to Suspension Subsystem.
The name of your subsystem, my_macpherson, appears next to the icon.
4. Select OK.
5. When Adams/Car finishes creating the assembly, select Close.
To define a preload:
1. Right-click either spring, point to the name of the spring, and then select Modify.
2. Set Installed Length to 135.0.
3. Select OK.
To change to kinematic mode:

The Toggle Kinematic Mode text box should already contain the name of your subsystem.
2. Set Current Mode to Kinematic.
3. Select OK.
To perform a kinematic suspension analysis:

109
Adams/Car performs the analysis and displays messages about the simulation.

The suspension animates through full jounce and rebound.

1. Launch Adams/PostProcessor just as you did in Plotting Results.
3. Set up the plots as follows:
• Plot Configuration File:
mdids://acar_shared/plot_configs.tbl/mdi_suspension_parallel_travel.plt
• Plot Title: My MacPherson
4. Verify that Cross Plotting is not selected.
5. Select OK.
Adams/Car automatically generates a series of plots based on this plot configuration file.
6. Cycle through the plots using the plot navigation tools.

Figure 18 shows the Toe Angle plot.
Figure 18 Plot of Toe Angle - Kinematic Analysis
7. After viewing the plots, return to Adams/Car.
Performing an Elasto-Kinematic Analysis

To run an elasto-kinematic analysis, you must first switch the mode from kinematic to compliant. This
turns off kinematic constraints and uses bushings for attachments between the parts.
Next, you must modify analysis parameters, and then run the analysis.
After the analysis is complete, you return to Adams/PostProcessor to compare analysis results.
To change to compliant mode:

111
2. Set Current Mode to Compliant.

3. Select OK.
To perform an elasto-kinematic analysis:

2. Set the Output Prefix to ela.
3. Select OK.
Adams/Car performs the analysis and displays messages about the simulation.
To plot the results of the elasto-kinematic analysis:

1. In Adams/PostProcessor, set up the comparison plots as follows:
• Plot Configuration File:
mdids://acar_shared/plot_configs.tbl/mdi_suspension_parallel_travel.plt
• Plot Title: My MacPherson
2. Select Cross Plotting.
3. Select OK.
Adams/Car creates plots with both analyses results included on each plot.
Figure 0-4 shows a comparison plot for the toe angle.
Figure 19 Toe Angle - Comparison Plot

Note that the elastic toe angle is greater than the toe angle as measured in kinematic mode.
117
Full-Vehicle Analysis Tutorial

Overview
This tutorial teaches you how to create a full-vehicle assembly, run different types of analyses, and view
the results.
To be able to run through this tutorial, you must have purchased the Adams/Car Vehicle Dynamics
Package.
• Opening a Full-Vehicle Assembly
• Performing a Single Lane-Change Analysis
• Performing a Quasi-Static Constant-Radius Cornering (CRC) Analysis
• Performing a Baseline ISO Lane-Change Analysis

119

In this tutorial, you run several analyses on a full-vehicle assembly, as shown in Figure 20, and then view
the results using animation and plotting. To perform the analyses, you create an assembly containing all
the subsystems in the full vehicle.
Figure 20 shows the full-vehicle assembly (front iso view, fit to view).
Figure 20 Full-Vehicle Assembly
After you create the full-vehicle assembly, you do the following:

• To quantify how the vehicle responds to steering inputs, you perform a single lane-change
(open-loop) analysis on the vehicle. A single lane-change analysis controls the steering
subsystem and simulates a simple lane-change maneuver with the set of parameters you enter
when you submit the analysis.
• To evaluate the vehicle’s understeer and oversteer characteristics, you run a constant radius
cornering analysis.
• To drive the vehicle through a lane-change course as described in ISO-3888, you run an ISO
lane-change analysis.
• After you run each analysis, you animate and plot its results.
121
Opening a Full-Vehicle Assembly

Using Adams/Car, you can group several subsystems and a test rig into an assembly. This grouping
simplifies the opening and saving of subsystems.
In this section, you open an assembly that references the subsystems and test rig for the full vehicle that
you are going to analyze. The assembly we’ve provided for you references the subsystems that
Adams/Car requires to perform steering maneuvers, acceleration maneuvers, and so on. Full-vehicle
assemblies reference the following subsytems:
• Front/rear suspensions
• Steering subsystem
• Powertrain
• Brake subsystem
• Front/rear tires
• Rigid chassis
By default, Adams/Car includes a vehicle test rig in the assembly.
To open an assembly:
2. From the File menu, point to Open, and then select Assembly.
3. Right-click the Assembly Name text box, point to Search, and then select the acar_shared
database.
4. Double-click MDI_Demo_Vehicle.asy.
5. Select OK.
The Message Window appears, informing you that Adams/Car is opening the assembly.
6. When Adams/Car is done loading the assembly, select Close.
Adams/Car displays the full-vehicle assembly.
Performing a Single Lane-Change Analysis

Now that you opened a full-vehicle assembly, you can submit a single lane-change analysis.
Performing a single lane-change analysis involves the following:
• Modifying Plot Layouts

You can now specify the inputs for the full-vehicle analysis and perform a single lane- change maneuver.
A single lane-change maneuver inputs a one-cycle sinusoid to the steering wheel with the cycle length
(time) and maximum steer value (amplitude) you enter.
To set up the analysis:

1. From the Simulate menu, point to Full-Vehicle Analysis, point to Open-Loop Steering Events,
and then select Single Lane Change.
123
Represent the duration and

the resolution of the analysis
Adams/Car updates the force entities, such as dampers, springs, and bushings, with the values
specified in their property files and sets up the vehicle assembly for the maneuver. Setting up the
vehicle assembly includes adjusting the road height so the road is in contact with the tires and
deactivating certain motions and forces, depending on the type of steering input you selected and
the inputs you specified. For example, because you set the steering input to angle, Adams/Car
deactivates the torque on the steering wheel and the force on the rack, and activates a motion on
the steering wheel revolute joint.
The test rig, which is part of the assembly, applies the inputs you specified in the analysis
submission dialog box to the assembly, and performs a static analysis, followed by a dynamic
analysis.
You are now ready to animate and plot the results.

In this section, you view the analysis you just ran. Adams/Car has already loaded the analysis results files
for you.
Before you animate, you might want to change the magnification of your assembly so you can see the
path the vehicle is taking.
To change the magnification of your assembly:

1. When the cursor is in the center of the main window, type a lowercase z.
2. Hold down the left mouse button, and do either of the following:
• To enlarge the display of the assembly, or zoom in, move the cursor up.
• To shrink the display of the assembly, or zoom out, move the cursor down.
3. To exit zoom mode, release the mouse button.
4. Animate the results just as you did in Animating the Results.
5. If you want the vehicle to always be in the center of the screen, do the following:
• Toggle Fixed Base to Base Part.
• Right-click the text box under Base Part, point to body, and then select Browse.
• The Database Navigator appears.
• From the list under MDI_Demo_Vehicle, double-click TR_Body, and then double-click
ges_chassis.
6. If you want to see the path the vehicle takes, do the following:
• Toggle No Trace to Trace Marker.
• Right-click the text box under Trace Marker, point to Marker, and then select Browse.
• The Database Navigator appears.
• Double-click TR_BODY.
• Double-click ges_chassis.
• Double-click cm.
7. To run another animation with either of the options presented in Steps 5. or 6., select the Play tool.
Adams/Car animates the vehicle.
8. To return the assembly to its initial configuration, select the Reset tool .

In this section, you create two plots that represent the following:
125
• Vehicle lateral acceleration as a function of time

• Roll angle of the vehicle as a function of the lateral acceleration
To create a plot of the lateral acceleration with respect to time:

1. From the Review menu, select Postprocessing Window.
3. From the Simulation list, select fveh_test_sin.
5. From the Request list, select chassis_accelerations. You might have to scroll to see this option.
6. From the Component list, select lateral.
7. Set the Independent Axis to Time.
Adams/PostProcessor displays the plot you requested, as shown next:
Figure 21 Plot of Lateral Acceleration versus Time

Note: Although the y-axis shows NO UNITS, acceleration is expressed in Gs.
To create a plot of the roll angle with respect to lateral acceleration:

1. From the Request list, select chassis_displacements.
2. From the Component list, select roll.
3. Set the Independent Axis to Data.
5. From the Request list, select chassis_accelerations. You might have to scroll to see this option.
7. Select OK.
8. From the dashboard, select Clear Plot.
127
Figure 22 Plot of Roll Angle versus Lateral Acceleration
Modifying Plot Layouts

To make a plot ready for a report, you can assign a title or subtitle to the plot, just as you did in Plotting
Steering Wheel Torque versus Steering Wheel Angle.
To assign a title or subtitle:

1. Assign the following title to your plot: Roll Angle versus Lateral Acceleration.
2. Assign the following subtitle to your plot: plot1.
Performing a Quasi-Static Constant-Radius Cornering

(CRC) Analysis
You use a CRC analysis to evaluate your full vehicle’s understeer characteristics. The CRC analysis holds
the turn radius constant and varies the vehicle’s lateral acceleration. A control subroutine, CONSUB,
controls the analysis and balances all the forces on the body and applies a lateral acceleration to all model
parts.
Submit a CRC analysis and view the results as explained in the following sections:
• Animating and Plotting the Results

You can now specify the inputs for the full-vehicle analysis and perform a quasi-static maneuver.

1. From the Simulate menu, point to Full-Vehicle Analysis, point to Quasi-Static Maneuvers, and
then select Constant Radius Cornering.
2. Run an analysis with the following specifications:
• Output Prefix: fveh
• Final Lateral Accel: .9
• Turn Radius: 50
• Set the units pull-down menu for the turn radius to m.
3. Select OK.
Adams/Car updates the properties of force entities such as dampers, springs, and bushings, with
the values specified in their property files and sets up the vehicle assembly for the maneuver.
The number of steps for the output is directly related to the acceleration increment (that is,
acceleration increment = final lateral acceleration / number of
steps). Adams/Car performs a static analysis at each lateral acceleration increment. When the
vehicle reaches the specified final lateral acceleration, the maneuver ends automatically or if the
vehicle’s lateral acceleration limit is less than the final lateral acceleration, Adams/Solver reports
failures and stops the maneuver.
Animating and Plotting the Results

In this section, you view the results of the analysis you just ran. Adams/Car has already loaded the
analysis results files for you. Before you animate, you should change the magnification of your assembly
so you can see the path the vehicle is taking.
129
After you animate, create plots using a plot configuration file (.plt), as explained next.
To create plots associated with the maneuver:

3. Right-click the Plot Configuration File text box, point to Search, and then select the
acar_shared database.
4. Double-click mdi_fva_ssc.plt.
5. Select OK.
You have automatically created a series of plots associated with this type of maneuver.
Adams/PostProcessor displays the first plot, as shown next:
Figure 23 Plot of Steering Angle versus Lateral Acceleration
6. To view the rest of the plots, select them from the treeview. For example, to view the second plot,
select page_plot_2.
Adams/Car displays a plot of the chassis roll angle versus lateral acceleration.
131
Performing a Baseline ISO Lane-Change Analysis

You now perform a baseline ISO lane-change analysis on the new assembly and then plot and view the
results. You then modify the spring and analyze the assembly again.
In an ISO lane-change analysis, the Driving Machine drives your full vehicle through a lane-change
course as described in ISO-3888: Double Lane Change. You specify the gear position and the desired
speed at which to perform the lane change. The analysis stops after the vehicle travels 250 meters;
therefore, the time to complete the maneuver depends on the speed you input.
The following sections explain how to perform a baseline ISO lane-change analysis:
• Animating and Plotting the Results
• Saving the Plot Configuration
• Modifying the Full-Vehicle Assembly
• Performing an Analysis on the Modified Full-Vehicle Assembly
• Comparing Analysis Results

You can now specify the inputs for the full-vehicle analysis and perform an ISO lane-change maneuver.
Note that the analysis is event-based, so its duration depends on the dynamic of the vehicle and on the
length of the course.

1. From the Simulate menu, point to Full-Vehicle Analysis, point to Course Events, and then
select ISO Lane Change.
2. Set up the analysis with the following characteristics:
• Output Prefix:iso1
• Initial Velocity:100 (km/h)
• Gear Position: 3
3. Select OK.
Adams/Car updates the properties of force entities, such as dampers, springs, and bushings, with
the values specified in their property files and then sets up the vehicle assembly for the maneuver.
When you submit the analysis, Adams/Car automatically generates an event file (.xml). The
name of the .xml follows the same naming convention as the other files that Adams/Car
generates: output_prefix_maneuver_name.
The test rig, which is part of the assembly, applies the inputs you specified in the .xml to the
assembly, and performs a dynamic analysis.
For information on the Driving Machine and XMLs, see the online help for Adams/Car.
Note: XML event files replace TiemOrbit DCF files. Adams/Car still supports DCF files, but it
automatically converts them to their XML representation.
4. To modify or view an XML event file, follow these steps:

• From the Simulate menu, point to Full Vehicle Analysis, and then select Event Builder.
• From the File menu in the Event Builder menu, select Open.
• Browse to the current working directory, and then double-click iso1_ilc.xml.
• To locate the current working directory, from the File menu in Adams/Car, choose Select
Directory. This displays a file browser with the current working directory highlighted.
For more information on the Event Builder, see the F1 help.
The path description of the ISO lane-change course is referenced in the <DcfMachine> tag of
ISO lane change of the .xml file. This information is stored in a driver control data (.dcd) file,
as shown on the next page.
5. [MDI_HEADER]
FILE_NAME = iso_lane_change.dcd
FILE_TYPE = 'dcd'
FILE_VERSION = 1.0
FILE_FORMAT = 'ASCII'
(COMMENTS)
{comment_string}
'Example DCD file of ISO-Lane Change Path'
$------------------------------------------------UNITS
[UNITS]
LENGTH = 'meters'
FORCE = 'newton'
ANGLE = 'radians'
MASS = 'kg'
TIME = 'sec'
$------------------------------------------------CLOSED_LOOP
[CLOSED_LOOP]
STEERING_CONTROL = 'path'
SPEED_CONTROL = 'none'
6. (DATA)
{ X Y }
0.0 0.000
45.0 0.000
52.5 0.000
60.0 0.000
90.0 3.586
102.0 3.586
133
115.0 3.586
140.0 0.172
147.0 0.172
155.0 0.172
162.0 0.172
170.0 0.172
200.0 0.172
300.0 0.172
400.0 0.172
500.0 0.172
For information on .dcd files, see the online help for Adams/Car.
Animating and Plotting the Results

Adams/Car has already loaded the analysis results files for you, so you can now view the results of the
analysis you just ran. Before you animate, you should change the magnification of your assembly so you
can see the path the vehicle is taking.
After you animate, create two plots to represent the following:
• Vehicle lateral acceleration versus time
• Roll angle of the vehicle versus the lateral acceleration
To create a plot of the lateral acceleration versus time:

2. Select Clear Plot.
4. From the Simulation list, select iso1_ilc.
6. From the Request list, select chassis_accelerations.
Figure 24 Plot of Lateral Acceleration versus Time

To create a plot of the roll angle with respect to lateral acceleration:

1. Select Clear Plot.
2. From the Request list, select chassis_displacements.
3. From the Component list, select roll.
4. Set the Independent Axis to Data.
6. From the Request list, select chassis_accelerations.
8. Select OK.
Figure 25 Plot of Roll Angle versus Lateral Acceleration

135
Saving the Plot Configuration

Saving the plot configuration allows you to easily recreate the plots later in this tutorial after you modify
the full-vehicle assembly.
To save the plot configuration:

1. From the File menu, point to Export, and then select Plot Configuration File.
2. In the Configuration File Name text box, enter iso_lane_change.
3. Make sure All Plots is selected.
4. Select OK.
Modifying the Full-Vehicle Assembly

To change the roll angle versus lateral acceleration vehicle characteristic, modify the spring by creating
and assigning a new property file.
After you create a spring property file, assign the newly created property file to the front and rear springs.
To create a new spring property file:

1.From the Tools menu, select Curve Manager.
2.From the File menu, select New.
3.Verify that Type is set to spring.
4.Select OK.
Adams/Car generates a plot of the spring displacement versus force
characteristic in the plot window of the Curve Manager.
5.In the Slope text box, enter 225.
6.Make sure the extension/compressions limits are set to
-100, 100.
7.Select Apply.
Adams/Car modifies the spring characteristic.
8.In the Free Length text box, enter 300.
9.Select Apply.
10.From the File menu, select Save.
11.In the File text box, enter my_spring.
12.Select OK.
13.Close the Curve Manager.
To modify the springs:

1. In the model, right-click the front spring, ns[lr]_ride_spring, and then select Modify.
The Modify Spring dialog box loads the spring parameters in the text boxes.
2. Right-click the Property File text box and, from your default writable database, select
my_spring.spr.
3. Replace Installed Length with Preload.
4. Enter a Preload of 5500.
5. Select Apply.
Adams/Car assigns the new property file to the spring.
6. Repeat Steps 1 through 4 for the rear springs.
7. Select OK.
137
Performing an Analysis on the Modified Full-Vehicle

Assembly
To determine how the modifications to the suspension subsystem affected the behavior of the vehicle,
perform another single lane-change analysis.

1. From the Simulate menu, point to Full-Vehicle Analysis, point to Course Events, and then
select ISO Lane Change.
2. In the Output Prefix text box, enter iso2.
3. Select OK.
Comparing Analysis Results

You now create a plot to compare the analysis results from the baseline vehicle assembly with the
analysis results from the modified vehicle assembly.
In addition to the plots defined in the plotting configuration file, you will review the vehicle velocity.
The Driving Machine longitudinal controller acts on the throttle demand to maintain the vehicle at the
desired speed.
To compare the analysis results:

3. In the Analyses text box, enter the iso1.ilc and iso2.ilc analyses.
4. Right-click the Plot Configuration File text box, and search your private database for
iso_lane_change.plt.
5. Select Cross Plotting.
6. Select OK.
Adams/PostProcessor displays a plot of the roll angle versus lateral acceleration.
The new spring property file has a linear stiffness of 225 N/mm versus the 125 N/mm of the original
spring files. A stiffer spring reduces the roll angle of the vehicle, effectively modifying the
handling behavior and the ride comfort of the vehicle.
To create a plot of the longitudinal velocity versus time:

1. Select the New Page tool.
2. From the Request list, select chassis_velocities.
3. From the Component list, select longitudinal.
Adams/PostProcessor displays the plot you just defined.

Getting Started Using Adams Car MDR3

Uploaded by

Copyright:

Available Formats

Getting Started Using Adams Car MDR3

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Getting Started Using Adams Car MDR3

Uploaded by

Copyright:

Available Formats

1

Getting Started Using Adams/Car

Starting Adams/Car Standard Interface

To start Adams/Car on Windows:

Figure 1 Adams/Car Standard Interface

Main shortcut menu

To start Adams/Car on UNIX:

2. Click the Adams/Car icon

3. Do one of the following:

Starting Adams/Car Template Builder

To check the user mode:

To start Adams/Car Template Builder on Windows:

Figure 2 Adams/Car Template Builder

Menus grayed out because

Main shortcut menu

View triad Status bar

To start Adams/Car Template Builder on UNIX:

2. Click the Adams/Car icon .

3. Select Template Builder.

Switching Between Interface Modes

To switch between modes:

Familiarizing Yourself with Adams/Car

Introducing the Driving Machine

About the Driving Machine

About the Event Builder

Using the Event Builder

To display the Event Builder:

To create a new file:

Entering Set-up and Global Parameters

Creating the Three Mini-Maneuvers

To create the mini-maneuvers:

4. In the Abort Time for MINI_2, change the abort time to 5.

Defining the Mini-Maneuver Parameters

To define mini-maneuver parameters for MINI_1:

To create end conditions for MINI_1:

Group Name: MINI_1

To define mini-maneuver parameters for MINI_2:

Control Method: machine

To create end conditions for MINI_2:

Delay Time: 0.0

To define mini-maneuver parameters for MINI_3:

To create the end condition for MINI_3:

Running the New Analysis

Suspension Analysis Tutorial

This tutorial takes about one hour to complete.

What You Will Create and Analyze

Figure 3 Suspension and Steering Assembly

Setting Up the Suspension and Steering Subsystems

Creating a New Front Suspension Subsystem

To create the front suspension subsystem:

3. In the Subsystem Name text box, enter UAN_FRT_SUSP.

Figure 4 Suspension Subsystem

To save the suspension subsystem:

Creating a Suspension Assembly

To create the suspension assembly:

Performing a Baseline Parallel Wheel Travel Analysis

Defining Vehicle Parameters

To define vehicle parameters:

Performing the Analysis