OSPF Questions

BSCI - OSPF Questions
Tuesday, 17 March 2009 23:55 administrator
Here we will find answers to OSPF questions
BSCI - OSPF Questions

Tuesday, 17 March 2009 23:55 administrator
Here we will find answers to OSPF questions
Question 1:
An administrator Pipes in the command router ospf 1 and receives the error
message: "OSPF process 1 cannot start." (Output is omitted.) What should be
done to correctly set up OSPF?
A - Ensure that an interface has been configured with an IP address

B - Ensure that an interface has been configured with an IP address and is up
C - Ensure that IP classless is enabled
D - Ensure that the interfaces can ping their directly connected neighbors
Answer: B
Question 2:
During a recent OSPF election among three routers. RTA was elected the DR
and RIB was elected the BDR, as seen in the graphic. Assume that RTA fails,
and that RIB takes the place of the DR while RTC becomes the new BDR.
What will happen when PTA comes back online?
A - RTA will take the place of DR immediately upon establishing its adjacencie
B - RTA will take the place of DR only if RTB fails
C - RTA will take the place of DR only if both RTB and RTC fail
D - A new election will take place establishing an all new DR and BDR based
on configured priority levels and MAC addresses
Answer: C
Question 3:
Refer to the exhibit. During the process of configuring a virtual link to connect
area 2 with the backbone area, the network administrator received this
console message on R3:
*Mar 1 00:25:01.084: %OSPF-4-ERRRCV: Received invalid packet: mismatch
area ID, from backbone area must be virtual link but not found from
20.20.20.1, Serial 0
How should the virtual link be configured on the OSPF routers to establish full
connectivity between the areas?
A - R1(config-router)# area 1 virtual-link 30.30.30.3
R3(config-router)# area 1 virtual-link 20.20.20.1
B - R1(config-router)# area 1 virtual-link 20.20.20.2
C - R1(config-router)# area 0 virtual-link 1.1.1.1
D - R1(config-router)# area 1 virtual-link 3.3.3.3
E - R1(config-router)# area 1 virtual-link 2.2.2.2
Answer: D
Explanation:
When designing a multi-area OSPF network, all areas should be connected to

the backbone area. However, there may be instances when an area will need
to cross another area to reach the backbone area like area 2 in this case. A
virtual link has the following two requirements:
+ It must be established between two routers that share a common area and
are both ABRs.
+ One of these two routers must be connected to the backbone.
In this case, two routers that satisfy the above requirements are R1 and R3.
The syntax for creating a virtual link across an area is:
area <area-id> virtual-link <neighbor-router-id>
The area-id is the number of the transit area, in this example Area 1 and
neighbor-router-id is the IP address of the highest loopback interface
configured or can be manually set on the neighboring router.
Question 4:
As shown in the exhibit ,OSPF is configured over a Frame Relay network. All
PVCs are active. However, P4S1 and P4S3 fail to see all OSPF routes in their
routing tables. The show ip ospf neighbor command executed on P4S2
displays the state of the neighbors. In order to fix the problem , what should
be done?
A - The neighbor command should be configured under the OSPF routing

process on all routers
B - The ip ospf network broadcast command should be configured on each
Frame Relay interface
C - The ip ospf network non-broadcast command should be configured on
each Frame Relay interface
D - The ip ospf priority value on the spoke routers should be set to 0
Answer: D
Explanation:
In an NBMA network topology, neighbors are not discovered automatically.

OSPF tries to elect a DR and a BDR due to the multi-access nature of the
network, but the election fails since neighbors are not discovered because
NBMA environment doesn't forward broadcast and multicast packets.
Neighbors must be configured manually to overcome these problems.
Also, additional configuration is necessary in a hub and spoke topology to

make sure that the hub routers, which have connectivity with every other
spoke router, are elected as the DR and BDR. You must set the spoke
interfaces to an OSPF priority of zero, this ensures that the spokes will not
become the DR or BDR.
Question 5:
The following exhibit shows ipv6 route output. What would the metric be for a
summary route that summarizes all three OSPFv3 routes displayed?
A - 160
B - 140
C - 120
D - 100
Answer: D
Explanation:
The cost of the summarized routes is the highest cost of the routes being
summarized. In fact, in the old RFC 1583 standard, the cost of the summary
route was the cost of the lowest metric. But when OSPF was updated in RFC
2178 and RFC 2328, the summary route should have the same cost as the
highest-cost summarized route. In this case, the highest-cost is 100 according
to the second entry.
Question 6:
Study the exhibit below carefully. In order to summarize all routes from area 0
to area 1, what must be configured on the router?
A - area 0 range 172.16.96.0 255.255.224.0

B - area 1 range 172.16.96.0 255.255.224.0
C - area 1 range 172.16.96.0 255.255.0.0
D - area 0 range 172.16.96.0 255.255.255.0
Answer: A

OSPF Questions

Uploaded by

Copyright:

Available Formats

OSPF Questions

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

OSPF Questions

Uploaded by

Copyright:

Available Formats

During a recent OSPF election among three routers. RTA was elected the DR and RIB was elected the BDR, as seen in the graphic. Assume that RTA fails, and that RIB takes the place of the DR while RTC becomes the new BDR. What will happen when PTA comes back online?

BSCI - OSPF Questions

Tuesday, 17 March 2009 23:55 administrator

Here we will find answers to OSPF questions

BSCI - OSPF Questions

Here we will find answers to OSPF questions

A - Ensure that an interface has been configured with an IP address

When designing a multi-area OSPF network, all areas should be connected to

area <area-id> virtual-link <neighbor-router-id>

A - The neighbor command should be configured under the OSPF routing

In an NBMA network topology, neighbors are not discovered automatically.

Also, additional configuration is necessary in a hub and spoke topology to

A - area 0 range 172.16.96.0 255.255.224.0

You might also like