LCD COLOUR TV

SERVICE MANUAL
CHASSIS NO.: LS01

Please read this manual carefully before service.

Catalog
Chapter1 Chapter2 Chapter3 Specifications and Composition ....................................................... 3 Function Introduction of Main IC
................................................... 7

Analysis of Signal process Flowchart and key point measure date .................................................................................................... 29

Chapter4 Maintenance Procedure and Examples of Typical troubleshooting .............................................................................................. 39 Chapter5 Chapter6 Spare Part Lists ............................................................................................. 40 Factory Setup and notice ...................................................................... 41

Appendix: 1. Circuit Schematic diagram 2. Circuit Schematic diagram of power module 3. Final Assembly diagram 4. Wiring diagram of LCD TV with LS01 chassis (take LT32GJ01E as an example)

Chapter 1:
1. Models for LS01 chassis : Region Europe LT26GJ01E LT37GJ01E LT32GJ12E LT26GJ88E LT37GJ88E

Specifications and Composition

America LT26GJ01U LT37GJ01U LT32GJ12U LT26GJ88U LT37GJ88U LT32GJ01U LT26GJ12U LT37GJ12U LT32GJ88U

Other regions LT26GJ01A LT37GJ01A LT32GJ12A LT26GJ88A LT37GJ88A LT32GJ01A LT26GJ12A LT37GJ12A LT32GJ88A

Original Models

LT32GJ01E LT26GJ12E LT37GJ12E LT32GJ88E

2. Main Feature
Region Color system RF signal Sound system Video or Y/C signal Program presetting Audio output THD 7% Power source Teletxt CCD Sound demodulator SCART VGA YPbPr HDMI Earphone OSD language Auto Off without Signal Reception Program booking Swap Energy saving system Plug and Play Europe PALSECAM D/KB/GIL/L PALNTSCSECAM 100 0-99 5W+5W 100V240V 100 pages X NICAMIGR Yes Yes Yes Yes Yes English, French, German, Italian, Portuguese etc. 5 minutes 5 program booking. Turn to the corresponding program at the booking time. Customer could rearrange the channels according to personal habit Customer could adjust LCD screen backlight brightness manually to save energy. LCD TV could be used as computer screen, no need for the installation of software, which is Plug and Play in real sense America NTSCPAL MPAL N M PALNTSCSECAM 68 AIR2-69 125 CABLE1-125 5W+5W 100V240V X Yes BTSC X Yes Yes Yes Yes English, French, Portuguese, Spanish etc. Other regions PALNTSCSECAM D/KB/GIM PALNTSCSECAM 236 0-235 5W+5W 100V240V 100 pages X NICAMIGR X Yes Yes Yes Yes English, French, German, Spanish etc.

3.

Unit IC Compositions

LCD TV with LS01 chassis is made up of switch power, system control circuit, video processing circuit, audio processing circuit, Power Amplifier circuit, AV input circuit, LCD screen module. Block circuit diagram is shown as below:

1) European market:

2). American and Asian market:

4. Introduction of PCB module LCD TV with LS01 is made up of power board, side AV board, remote control reception board, key board, and mainboard. The table below is the introduction of the function of all printed board modules.

No.

Parts

Description Mainboard module is the core of LCD TV signal processing. Under the control of the system control circuit, It undertakes the task of converting the external input signal into the unified digital signal that the LCD screen could identify. Mainboard controls the whole machine through IIC bus, decode VIDEO signal, controls the Video (brightness, contrast, chroma, hue, definition etc), white balance adjusts, generates OSD, de-interlaces signal, converts signal frequency, and finishes signal A/D and D/A conversion, video enhancement, LVDS signal coding and output; it has Scart , S-Video, AV , YPbPr, HDMI and PC interface, Tuner input, sound demodulation, sound processing, sound power amplifier, and online update. The remote reception board module is constituted by an indicator-light and a remote reception. Customer could manipulate the LCD TV by using remote controller very conveniently. By the color of the indicator light, the operation mode of the LCD TV could be judged (red is standby, green is power on).

Mainboard module

Remote 2 reception module

Built-in power Convert the 100V240V 50/60HZAC into DC, output have +24v, +12V, board module +5V, and the +5V_STB in standby state. Keyboard module Keyboard module has 7 function keys (program +/-, volume +/-, AV/TV, menu ,power), customer could use the key to operate the TV freely.

LCD screen has built-in inverter that convert DC into high voltage AC signal to LCD screen turn on the backlight CCFL (Cold Cathode Fluorescent Light); the LCD screen 5 module process the video signal from signal board and reappear. 6 Side board AV Side AV board is used for earphone output.

Chapter 2:

Function Introduction of Main IC

1. Main ICs and functional modules of LS01 chassis No. 1 2 3 4 5 6 7 8 9 10 11 12 14 16 18 19 20 21 22 24 25 26 Item no. U15 U1 U2 U3 U4 U5 U6 U8 U9 U35 U14 Model JS-6H2/121 SVP-CX32LF IS42S32200C1-6TL AT24C64A-10PU-2.7 T5BS4-9999 SST39VF040-70-4C-NHE 74ALVC573PW TCM809SENB713 74HCT4052D STV-8217/STV-8218 74LVC14AD Main function Tuner output sound IF and video signal

Video decoder, image processor, A/D and D/A conversion SDRAM with 2MX32bits EEPROM MCU Flash, Store the Control program. Address latch, to latch the address wires Hardware reset IC of MCU Audio input switch of AV terminal Audio signal processor VGA line and field synchronizing signal waveform shaping EEPROM 3.3V to 1.8V DC conversion 5V to 3.3V DC conversion 5V to 3.3V DC conversion 5V to 1.8V DC conversion 12V to 8V DC conversion HDMI digital audio decode, DAC ESD protection device of HDMI HDMI digital signal decode (SDA, SCL) used for program update Audio amplifier (BTL output)

U16U25 AT24C02BN-10SU-1.8 U18U22 AZ1117H -1.8TRE1 U19U24 AZ1117H -3.3TRE1 U20 U21 U23 U26 AZ1084S -3.3TRE1 AZ1084S -1.8TRE1 AZ78L08ZTR-E1 CS4344-CZZ

U28U29 Rclamp0514M.TBT U30 U31 U33 ANX9011L PI5C3306LE TDA8944J

2.

Function introduction of ICs or functional module of LCD TV with LS01chassis

1.Tuner (JS-6H2/121 or CDT-6GPL22-00) Pin No. Definition of pin 1 NC 2 BT 3 VCC 4 SCL 5 SDA 6 AS 7 AFS 8 NC 9 NC 10 NC 11 SIF/Out 12 13 14 Video/Out VCC+5V Audio/Out

Function description No connection No connection +5V power IIC bus (clock) IIC bus (data) Ground Ground No connection No connection No connection Sound intermediate Frequency output CVBS signal output +5V power Audio signal output

2. Image processing IC SVP-CX32LF The SVPTMCX video processor is a highly integrated system-on-a-chip device, targeting the converging HDTVready and PC-ready LCD TV, PDP TV applications where high precision processing of video and data are the requirements. SVPTMCX contains 6th generation dual-purposed triple 10-bit high-precision and high speed video ADCs for both PC and video inputs, the high-performance multi-format 3D digital comb video decoder that supports NTSC, PAL, and SECAM*, a HDTV sync separator, motion adaptive de-interlacing engine, and the video format conversion engine, supporting multi-window display in many different output modes. Tridents DCReTM Digital Cinema Reality engine, is integrated inside the SVPTMCX family to provide the most natural cinema-realistic images. The DCReTM technology integrates advanced 3D-comb video decoding, advanced motion adaptive de-interlacing, object-based digital noise reduction, advanced 6th generation scaler, film mode support, average picture level (APL), edge smoothing and dynamic sharpness enhancement. Trident's patented Unified Memory Architecture (UMA) that allows frame rate conversion, 3D comb video decoding, and video enhancement processing to share the same memory buffer that is made up of high-speed and cost-effective PC graphic memory. All these advanced digital processing techniques combined with a true 10-bit video data processing for the most optimal video fidelity to provide the most natural and cinema quality video images. Designed for maximum system design flexibility, SVPTMCX integrates all video interfaces to support converging digital video, analog video, and PC data applications. The users of Trident's single chip SVPCX series video processor(s) will benefit from many features while maintaining a price competitive advantage over the existing solution(s) Main features: Integrated 6th Generation Motion and Edge Adaptive De-interlacing Integrated ADC PC auto tune Built-in 8-bit LVDS Transmitter 6th generation cubic-4 image scaling engine Advanced Chroma Processing and Dynamic Contrast Function
8

 Green color stretch, blue color stretch, skin color enhancement Integrated 6th Generation Motion Adaptive 3D Digital Comb Video Decoder with Programmable Filter 60Hz100Hz interlaced scanning and 50Hz75Hz progressive scanning frame rate conversion 14D dynamic picture enhancements Advanced Film Mode Recovery-3:2/2:2 pull down Build-in A/D conversion function Teletext function Supports 16/32bits SDRAM memory interface Multi-screen display mode OSD and VBI/Closed caption and advanced OSD engine Pin function description: Pin No. Designation of pin Function of pin Analog signal input/output terminal 169 180 181 182 183 188 189 190 191 192 196 197 198 199 171 170 173 172 174 175 184 185 37 29 26 25 CVBS1 Y_G1 Y_G2 Y_G3 PC_G PR_R1 PR_R2 PR_R3 PC_R C PB_B1 PB_B2 PB_B3 PC_B FS1 FS2 FB1 FB2 VREFP_1 VREFN_1 VREFP_2 VREFN_1 DP0 DP8 DP9 DP10
9

CVBS input 1 Y input SCART1 Green signal input S-Video Y signal input PC Green signal input DVD interface Pr signal input SCART1 Red signal input SCART2 Y signal input PC Red signal input S-Video C signal input DVD interface Pb signal input SCART1 Blue signal input SCART1 CVBS signal input PC blue signal input No connection No connection SCART1 RGB_FB signal input SCART2 chroma signal input A/D conversion1 voltage reference + A/D conversion 1 voltage reference A/D conversion 2 voltage reference + A/D conversion 2 voltage reference Digital signal I/ODP0~DP23interface

Digital signal terminal

24 22 21 18 14 11 7 55 57 58 60 59 62 63 61 56 84 86 85 4 5 23 6 64 71 83 76 162 163 157 158 159 205 204 SDRM 124

DP11 DP12 DP13 DP14 DP18 DP19 DP23 PWMO SCL SDA GPIO0 GPIO1 WR# RD# CS INTN ALE RESET V5SF DP_HS DP_VS DP_CLK DP_DE_FLD ADDR0 ADDR7 A_D0 A_D7 CVBS_OUT2 CVBS_OUT1 TEST MODE AIN_HS AIN_VS XTALI XTALO MA0
10

CPU control terminal Pulse width modulation input IICclock IICdata GPIO1 selection signal GPIO2 selection signal CPU write signal CPU read signal CPU chip selection signallow level effective Interrupt signallow level effective Address latch signal Reset signal (high level effective) SF Power+5V Line synchronization signal Field synchronization signal Digital port Clock DE I/O terminal CPU addressR0~R7signal

CPU address/data passage

MISC port control signal SCART2 interface CVBS signal output SCART1 interface CVBS signal output Test mode signal (grounding) Line synchronization signal Field synchronization signal Crystal oscillator interface

Memory address A0~A11

121 118 113 125 126 156 133 109 87 128 127 130 131 132 112 129 111 155 148 145 138 107 100 95 88 LVDS port 52 38 39 47 46 43 42 51 50 49 48 45

MA3 MA4 MA9 MA10 MA11 DQM0 DQM1 DQM2 DQM3 BA0 BA1 RAS# CAS# WE# CLKE CS0# MCK MD0 MD7 MD8 MD15 MD16 MD23 MD24 MD31 LVDS_VDDP PLL_GND PLL_VCC LVDSGND LVDSVCC TCLK1M TCLK1P TA1 M TA1P TB1M TB1P TC1M
11

Memory read/write byte signal

Memory stack address selection RAS signal CAS signal Memory write pulse Memory clock pulse Memory chip selection signal Memory clock signal

Memory data interface

Power for LVDS PLL ground PLL power LVDS ground Power for LVDS Positive/Negative LVDS differential clock output Positive/Negative LVDS differential data output

44 41 40 Clock and power 146 134 108 98 72 19 160 136 119 96 74 53 27 12 13 28 54 75 97 120 137 161 20 73 99 110 135 147 195 168 2 207 1 3 206 208 203 202 201

TC1P TD1M TD1P VDDM VDDM VDDM VDDM VDDH VDDH VDDC VDDC VDDC VDDC VDDC VDDC VDDC VDDC VSSC VSSC VSSC VSSC VSSC VSSC VSSC VSSC VSSH VSSH VSSM VSSM VSSM VSSM AVDD3_ADC2 AVDD3_ADC1 PLF2 MLF1 PAVSS2 PAVDD2 PAVSS1 PAVDD1 PAVSS PAVDD PDVSS ADC analog power (+3.3V) Video PLL clock low pass filtering Memory PLL clock low pass filtering PLL ground PLL power (+1.8V) PLL digital ground PLL digital ground power (+1.8V) PLL Digital ground PLL digital ground power(+1.8V) PLL Digital ground
12

Memory port digital power

3.3V power supply

1.8V power supply

Digital ground

200 177 186 193 178 176 187 194 179 165 164 166 167

PDVDD AVDD_ADC1 AVDD_ADC2 AVDD_ADC3 AVDD_ADC4 AVSS_ADC1 AVSS_ADC2 AVSS_ADC3 AVSS_ADC4 AVDD3_OUTBUF AVSS_OUTBUF AVDD3_BG_ASS AVSS_BG_ASS

PLL digital ground power (+1.8V)

ADC analog power (+1.8V)

ADC analog ground

+3.3V analog power Analog ground

SVP-CX32LF internal block diagram:

13

3T5BS4-9999 brief introduction: T5BS4-9999 is a high-speed 16-bit micro-controller designed for the control of various mid- to large-scale equipment. T5BS4-9999 is ROM-less product, T5BS4-9999 comes in a 64-pin flat package. Listed below are the features that is used for the control of a variety of small to large devices. T5BS4-9999 could extend ROM ,64 pins and is packaged in PLCC. It is the main control IC of the TV via IC bus. Main features: High speed 16-bit CPU900/L1 CPU Minimum instruction execution time: 148ns Build-in RAM: 10Kbytes Expandable up to 16Mbytes simultaneously support 8-/16-bit width external data bus 8-bit timers: 6 channels, 16-bit timers: 1 channel General-purpose serial interface: 1 channel Serial bus interface: 1 channel 10 bit A/D conversion interface: 4 channels Watchdog timer Timer for real time clock (RTC) Chip select/wait controller: 4 blocks 34 interrupt signals output 9 CPU interrupt, 21 internal interrupt, 4 external interrupt 53 I/O pins Standby function Clock control fs=32.768KHz real-time time of time conversion function high frequency fc to fc/16 Working voltage When fc=27 MHZ, VCC=2.7~3.6V, when fc=10MHZ, VCC=1.8V to 3.6V 64 pin packageP-LQFP64-1010-0.50D standard Pin assignment description:

14

Pin introduction: Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Designation AVSS P70/TA0IN P71/TA1OUT P72/TA3OUT P73/TA4IN P74/TA5OUT P80/TB0IN0/INT5 P81/TB0IN1/INT6 P82/TB0OUT0 P83/TB0OUT1 P90/TXD0 P91/RXD0 P92/SCLK0/ P93 P94 P95 AM0 DVCC Function description Analog ground IC data input IC clock output PAGE signal output +5V power Backlight on/off control Remote control signal +1.8V power supply Remote red control signal Remote green control signal Digital ground HDMI identity signal No connection CON4(10th pin) CON4(4th pin) CON4(3rd pin) Bus byte selection +3.3V power
15

19 20 21 22 23 24 25 26 27 28 35 36 43 44 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

X2 DVSS X1 AM1 P96/XT1 P97/XT2 NMI ALE P00/AD0 P07/AD7 P10/AD8/A8 P17/AD15/A15 P20/A0/A16 P25/A5/A21 P30/ P31/ P32/ P40/ P41/ P42/ P60/SCK P61/SO/SDA P62/SI/SCL P63/INT0 P50/AN0 P51/AN1 P52/AN2 P53/AN3/ AVCC

Crystal oscillator interface Ground Crystal oscillator interface Bus byte selection CPU reset control port Low frequency oscillation input interface Low frequency oscillation output interface Interrupt request signal Address latch pulse 0~7 bit address/data port

8~15 bit address/data port or 8~15 bit address port

8~5 bit address port or 8~21 bit address port External memory read control terminal External memory write control terminal (AD0~AD7) Data write control terminal (AD8~AD15) Internal address selection signal (no connection) IC data IC clock Interrupt request signal KEY signal port SCART1 FS signal SCART2 FS signal Analog power +3.3V

16

T5BS4-9999 internal functional block diagram

4STV-8217/STV-8218 brief introduction STV-8217/STV-8218 main features: Full-Automatic Multi-Standard Demodulation B / G / I / L / D / K / M / N Standards Mono AM and FM FM 2-Carrier and NICAM/BTSC

17

 Sound Processing: Loudspeaker ST royalty-free processing: ST WideSurround, ST OmniSurround (Virtual Dolby Surround and Independent Volume / Balance Smart Volume Control (SVC), 5-band equalizer and Loudness Analog Audio Matrix 4 stereo inputs 3 stereo outputs THRU mode 2 VRMS capability Pin introduction: Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Designation SC1_OUT_L SC1_OUT_R VCC_H GND_H SC3_OUT_L SC3_OUT_R VCC33_SC GND33_SC SC1_IN_L SC1_IN_R VREFA GND_SA VBG SC2_IN_L SC2_IN_R VCC33_LS GND33_LS SC2_OUT_L SC2_OUT_R VCC_NISO GND_SA VSS33_CONV VDD33_CONV SC3_IN_L SC3_IN_R Function description SCART1 audio output left SCART1 audio output right +8V power ground SCART3 audio output left SCART3 audio output right +3.3V power Ground SCART1 audio output left SCART1 audio output right Audio bias voltage decoupling interface Ground Audio bias voltage decoupling interface SCART2 audio input left SCART2 audio input right DACs power(+3.3V) DACs ground SCART2 audio output left SCART2 audio output right Polarization of the NISO+3.3V DACS ground DAC ground DAC power (+3.3V) SCART3 audio input left SCART3 audio input right
18

25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59

SCL_FLT SCR_FLT LS_C LS_L LS_R LS_SUB HP_LSS_L HP_LSS_R VSS18_CONV VDD18_CONV /HP_DET ADR_SEL VSS18 VDD18 SCL SDA VSS18 VDD18 /RST S/PDIF_IN S/PDIF_OUT VDD33_IO1 VSS33_IO1 CK_TST_CTRL VSS18 VDD18 CLK_SEL XTALIN_CLKXTP XTALOUT_CLKXTM VCC18_CLK1 GND18_CLK1 GND18_CLK2 VCC18_CLK2 VSS33_IO2 VDD33_IO2

SCART channel filtering left SCART channel filtering right No connection Left loudspeaker output Right ludspeaker output No connection No connection No connection DAC/ADC ground DAC/ADC power (8V) Earphone detection hardware address selection for IIC bus Digital ground +1.8V power IC bus clock IC bus data Digital ground +1.8V power Reset signal input/output terminal No connection No connection +3.3V power Digital ground Digital ground Digital ground +1.8V Power Clock input format selection Oscillator interface 1.8V for clock PLL Ground Ground +1.8V Power Digital ground +3.3V Power

19

60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80

I2S_PCM_CLK I2S_SCLK I2S_LR_CLK I2S_DATA0 I2S_DATA1 I2S_DATA2 VDD18 VSS18 BUS_EXP IRQ GND_PSUB VDD18_ADC VSS18_ADC SIF_P SIF_N GNDPW_IF VCC18_IF GND18_IF MONO_IN SC4_IN_L SC4_IN_R

No connection IS clock I/O channel1,2,3 IS selection signal input/output IS bus data input/output stereo channel 1 IS bus data input stereo channel 2 IS bus data input stereo channel 3 +1.8V Power Ground Bus-expander function No connection Ground +1.8V Power Ground Sound IF input (positive terminal) Sound IF input (negative terminal) Ground +1.8V Power Ground Mono input SCART4 audio input left SCART4 audio input right

20

STV-8217 internal block diagram:

21

STV-8218 internal block diagram:

5TDA8944J brief introduction: The TDA8944J is a dual-channel audio power amplifier with an output of 2* 7 W at an 8 load and a 12 V supply. The circuit contains two Bridge Tied Load (BTL) amplifiers with an all-NPN output stage and standby/mute logic. The TDA8944J comes in a 17-pin DIL-bent-SIL (DBS) power package. The TDA8944J is printed-circuit board (PCB) compatible with all other
22

types in the TDA894x family. One PCB footprint accommodates both the mono and the stereo products. main features: High integration Standby and mute mode No on/off switching plops High supply voltage ripple rejection Low standby current Outputs short-circuit protected to ground, supply and across the load Overheat protection Linear output to drive external earphone, PC and portable audio equipment Pin introduction: Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Designation OUT1GND1 VCC1 OUT1+ N.C. IN1+ N.C. IN1IN2MODE SVR IN2+ N.C. OUT2GND2 VCC2 OUT2+ Function description negative loudspeaker terminal1 Ground +12V Power positive loudspeaker terminal 1 No connection Positive pole input 1 No connection Negative pole input 1 Negative pole input 2 Mode selection input (standby, mute, operating)Operation mode selection (standby, mute, work) Half supply voltage decoupling (ripple rejection)Voltage decoupling filtering (grounding) Positive pole input terminal 2 No connection Negative loudspeaker terminal 2 Ground +12V Power Positive loudspeaker terminal 2

23

TDA8944J internal block diagram:

6. ANX9011L brief introduction: The ANX9011 is an advanced multimedia receiver compliant with High Definition Multimedia Interface (HDMI) Specification 1.1. HDMI is the first transport standard to unify digital video, audio, and control data over lowcost cables. It connects digital television, flat panel displays and project systems digitally to multimedia sources: DVD players, high definition settop boxes, digital video tape recorders, and personal computers. Digital transmission, in turn, delivers an uncompromising multimedia experience. HDMI also includes encryption for premium contents pursuant to the Highbandwidth Digital Content Protection (HDCP) standard. The ANX9011 embeds the HDCP keys and key selection vectors to reduce manufacturing complexity and system cost. Features: Single HDMI receiver supporting link data rate up to 165 MHz HDMI 1.1,HDCP 1.1 and DVI 1.0 compliant WideEye architecture for signal conditioning and equalization Support multi-format video processing 24 bit RGB / YCbCr 4:4:4 16/20/24 bit YCbCr 4:2:2 8/10/12 bit YCbCr 4:2:2 (ITU BT656) 12bit double data rate interface 24/48 bit single data rate interface Color space conversion: RGB to/from YCbCr both directions Auto video mode configuration Digital audio interface 32-192kHz audio sampling rate Provide 4-channel IIS interface for 8 audio channels Mute software configuration

24

Integrated HDCP decryption engine and preprogrammed keys Supports automated link integrity checking Programmable power management with automatic shutdown for power conservation 128 pin LQFP packaging Pin function Pin Designation Digital image output terminal 92 VDE23 96 VDE19 99 VDE18 101 105 108 117 121 124 2 5 8 11 14 17 20 23 26 29 32 35 119 127 128 1 VDE16 VDE12 VDE11 VDE4 VDE3 VDE0 VDO23 VDO20 VDO19 VDO16 VDO15 VDO12 VDO11 VDO8 VDO7 VDO4 VDO3 VDO0 VD_CLK DE HSYNC VSYNC Video output data clock Video output data effective level signal Line synchronizing signal Field synchronizing signal
25

Function description

24bitDP0~DP23digital video output data bus

24bitQO0~QO23no connection

Digital audio output terminal 85 84 79 76 75 74 71 70 XTAL_IN XTAL_OUT MCLKOUT IIS_SCK IIS_WS IIS_SD0 IIS_SD3 SPDIF Crystal oscillator interface Audio main control clock output IIS bus clock IIS signal selection IIS bus data IIS channel selection (no connection) no connection Mute control signal (no connection ) Interrupt request output Reset signal input DDC Clock signal DDC address/data signal IC bus clock IC address/data Synchronization detection IC connection detection signal Cable insert detection terminal Ground No connection

67 MUTEOUT Control signal port 91 INT 89 RESETN 42 DDC_SCL 41 DDC_SDA 40 CFG_SCL 39 CFG_SDA 90 HDMI_DET 38 DEVAD 44 HDMI_5V 88 RESDL 43 NC 45 NC HDMI input terminal 51 HDMI_CLKP 50 55 54 59 58 63 62 HDMI_CLKN HDMI_D0P HDMI_D0N HDMI_D1P HDMI_D1N HDMI_D2P HDMI_D2N

Differential clock input Differential data input1 Differential data input 2 Differential data input 3

Power and ground DVDD18 12, 24, 36, 51, 66, +1.8V digital Power 81, 82, 112, 125 DVDD33 7, 19, 31, 68, 77, +3.3V digital Power 98, 107, 120 AVDD33 47, 49, 53, 57, 61, +3.3V analog Power 86, 87

26

DVSS

AVSS

6, 13, 18, 25, 30, 37, 65, 69, 78, 80, Digital ground 97, 106, 113, 118, 126 46, 52, 56, 60, 64, Analog ground 83

ANX9011L internal block diagram:

7. 74HCT4052D brief introduction: 74HCT4052D is a 4-channel bi-directional analog multiplexer and multi-channel output selector. Each multi-channel output selector has 4 independent input/output terminals and 1 common input/output terminal. It is often used in analog and digital multiplexing, and multi-channel output selecting circuit and signal control system. Feature: -5V to +5V widely range Power input Low on-resistance Typical break before make built in Complies with JEDEC standard no. 7A ESD protection: HBM EIA/JESD22-A114-B exceeds 2000 V MM EIA/JESD22-A115-A exceeds 200 V. Specified from -40 C to +85 C and -40 C to +125 C. Automatic protection function

27

Pin introduction: Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 2Y0 2Y2 2Z 2Y3 2Y1 E VEE GND S1 S0 1Y3 1Y0 1Z 1Y1 1Y2 VCC Designation Function description PC left audio input HD left audio input Left audio input SCART2 left audio input AV left audio input Ground Ground Ground Select pulse input +3.3V Power SCART2 right audio input PC right audio input Right audio output AV right audio input HD right audio input +5V Power

74HCT4052D internal block diagram:

28

Chapter 3:

Analysis of Signal process Flowchart and key point measure date

This chapter mainly introduces the receipt and dispose of AV signal the power supply system and system control process of this TV. (Model of LT32GJ01E is taken as an example, other models is similar and will not be explained here for each. There are minor differences in power supply among different models of LCD screen; the details are shown in Specifications). 1. Video signal flow RF signal is demodulated by tuner, then the obtained video signal and signals inputted from COMPONENT terminal, AV, S-VIDEO, 2-way SCART interface and VGA interface are all sent into video-processing IC SVP-CX32LF for decoding. The different format input signals are changed into uniform LVDS signals, and are sent to LCD screen. In addition, TV video signal is processed by SVP-CX32LF to generate 2 CVBS signal, which are used in SCART video output. Signal inputted from HDMI interface is decoded into digital video signal BY ANX9011L, which is sent into video decoding IC SVP-CX32LF for decoding. After procession, the obtained uniform LVDS differential signal is sent into LCD Screen. 2.Sound process flow RF signal is demodulated by tuner, and then the obtained SIF signal (SIF-2 signal) and audio signal inputted from Scart1 interface are directly processed by STV-8217. The output audio signal of STV-8217 is sent into power amplifier TDA8944J, and the amplified signal is finally sent into speaker or earphone. Signals from HDTV terminal, AV terminal, Scart2 interface and PC Audio are first sent into 74HCT4052D for choosing passages, and then sent into STV-8217 for demodulation and sound process. The output audio signal of STV-8217 is sent into power amplifier TDA8944J, and finally the amplified signals are sent into speaker or earphone. After the demodulation and sound effect processing of STV-8217, there is an audio output which is used for sound output of Scart1 terminal. 3. Power supply system There are 4 ways of voltage output in the power panel: +24V6A +12V2A +5V2A and +5VS1A. +24V output is provided for LCD screen; +12V output is provided for power amplifier TDA8944J, and is also changed into +8V output by AZ78L08ZTR-E1 to supply STV-8217 IC; +5V output is changed into 1.8V output and 3.3V output by DC/DC (such as AZ1117H-1.8TRE1 and AZ1117H-3.3TRE1) to satisfy the needs ICs. +24V, +12V and +5V outputs will be cut off in standby state. While +5VS output is the power supply of MCU, infrared receiver and EEPROM etc, and will be cut off when the AC is turn off. 5V output will be divided into two ways: one way is changed into +3.3V and +1.8V analogue power supplies through DC/DC converter for STV-8217 IC, ANX9011LF IC etc and peripheral circuits; other way is changed into +3.3V and +1.8V digital power supplies through DC/DC converter for SVP-CX32 IC etc and peripheral circuits, and this way of 5V voltage will be cut off in standby state, while the other way of 5V voltage supply power especially for MCU, infrared receiver and EEPROM etc, and will still operating in standby state. (1) The composition and distribution of the TV power supply +12V power supply CON11 Pin 1,2,3 U23 AZ78L08ZTR-E1 8V ST82X7 Pin 3

FB18

12V

FB8

+12Vvoltage of line to screen CON1 Pin 1,2,3,4 (used by 37 inches screen)

+12V power supply CON403 Pin 3,4

12V power amplifier TDA8944J Pin 3,16 FB34 12V shutdown mute circuit
29

U18 AZ1117H-1.8TRE1

R206 CX_VA18 2.2mA 1.8V

U1 SVP-CX32 Pin 177,178,186,193 FB27 R3,R4 FB1,FB2 U30 Sil9011 Pin 12, 24, 36, 51, 66, 81, 82, 112, 125 U1 SVP-CX32 Pin 200,202,208,3

R213

CX_VL18 1.8V

AZ1084S-3.3TRE1 +3.3V

U30 Sil9011 Pin 7, 19, 31, 68, 77, 98, 107, 120 Pin 47, 86, 87 FB26 FB29 FB30,32 U30 Sil9011 pin 87,86 R214 U1 SVP-CX32 Pin 12,27,53,74,96, 119,136,160 U30 Sil9011 Pin 49, 53, 57, 61

FB23

5V

U21 AZ1084S-1.8TRE1

+5VCON11 Pin 7,8,9,10,11 FB20 2575mA

U20

U1 FB5,6 FB22 FB4 L1,2

SVP-CX32

Pin 19,72

U1 U1 U1

SVP-CX32 SVP-CX32 SVP-CX32

Pin 165,166 Pin 46, 39, 52 Pin 155,156

FB3 R2

U2 IS42S32200C1-6TL Pin 1,15,29,43,3,9,35,41,49,55,75,81

U1 FB21 +3.3V L24 L21 U35

SVP-CX32 Pin 98, 108, 134,146

U35 ST8217 Pin 7,16,20,22 ST8217 Pin 46 L28,29,22 U35 U22

AZ1117H-1.8TRE1 +1.8V

AZ1117H-3.3TRE1

ST8217 Pin51

U35 Y4

ST8217 Pin 42,76,54 27MHz XO voltage

U19

30

FB12

U9

74HCT4052D

Pin 16

Starting up mute circuit

+5VCON11 Pin7,8,9,10,11

FB16 FB24 FB17 FB7 FB20 R232 U30 R198

U15 U15

JS-6B2/121 JS-6B2/121

Tuner Pin 3 Tuner Pin 13

+5Vvoltage of line to screenCON1 Pin 1,2,3,4 (used by screen less than 32 inches) Sil9011 Pin 44 CON13 Pin 4,3

Back light switch control

R202 FB28

Back light height control

U26

CS4344-CZZ

Pin 9

U14 74LVC14AD Pin 14

U16,25 AT24C02BN Pin 8

U31 PI5C3306LE Pin 8

U28,29 0514M.TBT Pin 3

U1SVP-CX32Pin 85D7,8BAV99LPin 2 5V_SBCON12 Pin1,2 J3 FB19 R207 IIC Bus data interface R208 CON4, CON 15, CON 16 Pin 2,3 IIC Bus clock interface
U4

VGA terminal interface voltage

U24 FB25
AZ1117H-3.3TRE1

FB9
U5

T5BS4-9999 Pin 64
SST39VF040 Pin 32

+1.8V

FB10 FB11
U4

T5BS4-9999 Pin 18

CON14 Pin CON17 Pin CON5 Pin 1

U3AT24C64A-10PU-2.7Pin 8 U8TCM809SENB713 Pin 3 U674ALVC573PW Pin 20 Q892SK1399 Pin Q10112SC1815M-Y Pin

31

(2)

Pin level schedule for Voltage regulators on mainboard Component model AZ1117H-1.8TRE1 AZ1117H-3.3TRE1 AZ1084S-3.3TRE1 AZ1084S-1.8TRE1 AZ78L08ZTR-E1 Pin 1 2,3 4,5 Pin 1(V) GND GND GND GND 12V Pin definition ON/OFF GND 5V 5Vstb GND 12V 12VA GND 24Vio GND 24VI Pin 2(V) 1.8V 3.3V 3.3V 1.8V GND Pin 3(V) 3.3V 5V 5V 3.3V 8V

Position number U18U22 U19U24 U20 U21 U23 Position number

(3) Pin sequence of power cord of power panel Pin function discription LOFF HON GND +5V/4A +5V/1A GND +12V/1A +12V/2A GND +24V/1A GND +24V/4A

CON1

6 7,8 9,10 1,2

CON2

3,4,5,6 7,8

CON3

1,2,3 4,5,6

4. Position and definition of the main components and sockets on mainboard(see next page)

32

33

(1)

Socket definition Connecting object Power panel Power panel Back light control line Keyboard Remote control receiving board Standby Standby LVDS interface of line to screen IC Power panel Standby Standby Speaker Side AV board VGA audio signal input J8 J4 J2 J6 J3 CON2 HD, audio, video signal input & output HDMI input HD, audio, video signal input S terminal input VGA input Standby L+,L-,R+,R+5V_SB , +5V_SB , GND , GND , Power supply control Function description GNDGND+12V+12V +12V +12V +12V GNDGNDGND+5V +5V+5V+5V+5V GNDGNDback light switch controlback light brightness control +3.3VGNDKEY1KEY2 +3.3VREMOTEGNDindicator1indicator1

Serial Position number number 1 CON40 3 2 CON11 3 4 5 6 7 8 9 10 11 12 13 14 15 16 18 19 20 21 22 (2) CON13 CON14 CON17 CON4 CON5 CON1 CON15 CON12 CON13 CON8 CON9 CON10 J9

Main components descriptions Position number U16 U14 U2 U3 U8 U31 component Function description

Serial numbe r A B C D E F

AT24C02BN-10SU-1.8 EEPROM VGA line and field synchronizing signal 74LVC14AD shaping IS42S32200C1-6TL 2MX32bits SDRAM AT24C64A-10PU-2.7 TCM809SENB713 PI5C3306LE EEPROM MCU reset IC IC bus switcher for program upgrading

34

G H I J K L M N O P Q R S T U V

Video decoding, image processor, A/D and D/A conversion SST39VF040-70-4C-N Flash MEMORY storing whole machine U5 HE control program U4 T5BS4-9999 MCU Address latchfor latching and extending the U6 74ALVC573PW address line U18U21U22 AZ1117H-1.8TRE1 3.3V to 1.8V DC-DC Converter U1 SVP-CX32LF U20 U19 U24 U23 U26 U30 U25 U28U29 U35 U9 U33 AZ1084S-3.3TRE1 AZ1117H-3.3TRE1 AZ78L08ZTR-E1 5V to 3.3V DC-DC Converter 5V to 3.3V DC-DC Converter

12V to 8V DC-DC Converter HDMI digital audio decoding and D/A CS4344-CZZ conversion HDMI decoding, HDTV video/audio ANX9011L reproduction AT24C02BN-10SU-1.8 EEPROM Rclamp0514M.TBT STV-8217 74HCT4052D TDA8944J HDMI signal ESD protective device Sound Processor AV input sound passage switcher 2X7W Sound AmplifierBTL Output

U15 JS-6H2/121 Tuner 5. Waveforms at key points (1)RF inputting color bar signal, Composite Video Signal waveform at pin 14 of tuner U15, and the waveform at pin 169 of U1SVP-CX32LF is like this:

35

(2)RF inputting color bar signal, IC bus clock signal SDA, pin 5, 6 of U31, pin 6 of U16, pin 39 of U35, pin 58 of U4, pin 40 of U30, pin 57 of U1, pin 4 of tuner U15:

(3) RF inputting color bar signal, IC bus clock signal SDA, pin 2, 3 of U31, pin 5 of U16, pin 40 of U35, pin 57 of U4, pin 39 of U30, pin 58 of U1, pin 5 of tuner U15:

36

(4)RF inputting grey signal, Composite Video Signal waveform at pin 14 of tuner U15, and the waveform at pin 169 of U1SVP-CX32LF is like this:

(5)RF inputting white signal, SIF Signal waveform at pin 11 of tuner U15, and waveform at pin 73 of sound effect processing IC Stv-8217:

37

(6)RF inputting white signal, and inputting sound signal with 1KHz frequency, inductance waveforms at pin 28, 29 of U35, and waveform of L26,L27:

(7)Inputting sound signal with 1KHz frequency, with the processing of U33 and power amplifier TDA8944J, waveform at pin 1, 4, 14, 17 of U33, and waveform at CON13 speaker and CON14earphone output interfaces:

38

Chapter 4:

Maintenance Procedure and Examples of Typical troubleshooting

When you meet the following common problems, you might diagnose and get the solutions without contacting with the technicians. Symptoms No picture, no sound, and no indicator light on Possible Reason 1.The power cord is not plugged in 2.The power is off Solutions 1.Plug the power cord in 2.Turn the power on 1.Adjust the value of Contrast, sharpness, and color 2.Set the Color system to the country broadcasting standard 3.Set the Sound system to the country broadcasting standard Use the qualified signal cord Adjust the value of contrast, brightness, color and volume Connect the signal cable correctly Connect the correctly video cable

Picture and abnormity

sound

with

1.Contrast, sharpness, and color are set improperly 2.Color system is set improperly 3.Sound system is set improperly

Picture is spotted or with snow No picture, no sound and indicator light is green

Blue screen, AV or SVIDEO is displayed Picture is unclear or shaking or with black horizontal strips (in VGA mode) VGA picture is not centered No sound VGA picture display improper color HDMI source, with pixel of full screen with snow

Signal source is low-grade or the signal cord is in a lower quality Contrast, brightness, color and volume are all in the minimum value or TV is in mute mode. The signal cable is not correctly connected. There is no signal input or the video cable is not connected or incorrectly connected

VGA picture adjusted.

is

not

correctly

Enter into SETUP menu, select Auto Tracking item to perform automatic calibration and adjust Phase to solve the problem Connect the correctly audio cable

There is no audio signal input or audio cable is not connected correctly The color temp incorrectly by user The source standard is adjusted is not

Readjust the color temp, or select the original color setting Plug the HDMI cable again 1.Make sure the positive and the negative polarities are correct. 2.Check if there is a loose contact between the batteries and the springs 3.Replace the batteries

generate

The remote control does not work

Batteries are improperly installed or exhausted

39

Chapter 5: Spare Part Lists

This listing of maintenance and repair parts are presented for reference only, modification of parameters will not be informed. For accurate models or specifications, please consult the newest data of our company. (LT32GJ01E is taking an example) Number 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Name Panel frame Back cover Mount part Mainboard part Remote receiving board part Keyboard part Inner module LCD screen Electronic tuner Electronic tuner Dynamic speaker Dynamic speaker Remote emitter control GK23J2 power FSP205-5E01 V320B1-LXX JS-6H2/121 Inner power module LCD screen Electronic tuner Part code Part number JUG6.116.623 JUG6.116.624 JUJ7.356.005 JUG6.690.106 JUG6.695.028 JUG6.694.029 Print plate JUG7.820.015 Print plate JUG7.820.016 Print plate JUG7.820.017 Print plate number Proportion of easy damage 0.1 0.1 0.1 1 0.5 0.5 5 0.1 0.5 0.5 2 2 1

CDT-6GPL22-0 Electronic tuner 0 YDT613-A9-10 W-8 Dynamic speaker

YDG52-A3-10W Dynamic speaker -8 Remote emitter control

40

Chapter 6: Factory Setup and notice

1. Enter factory menu Switch on TV set, and make LCD at operating state: Press MUTE key on remote control Press MENU key on remote control, and switch to SOUND option with V+,V-key Move cursor to Balance option with P+,P-key to enter setting status Press number key 3 1 3 8on remote control to enter password. Entering factory mode is finished. PressPowerkey to switch off the TV and to quit factory mode. Factory menu display is presented like bellow chassisLS01 Jul 29 2006 23:25:16 VersionLSE01-M32-V1.05WL IC off Clear EPROM Panel Control Factory Setting System Control Min/Max CONTROL White Balance Hotel Option EPROM Edit Register Edit Jul 29 2006 23:25:16 Notes chassisLS01is the model number of local module is the latest upgrading time for software andVersionLSE01-M32-V1.05WLis the version number of current software. (2)The detailed setting items are given bellow: Contents of first page Remark Setting item Setting content Setting method Stop IC bus Used for updating IIC Off OKorV+,V-key communication program EPROM Press OK key first then Only done in first Clear EEPROM initialization press V-key setting station Screen back light Press V+ , V- keys to Panel Control brightness control(or enter submenu select the panel type) Press V+ , V- keys to Factory Setting Factory Setting enter submenu Press V+ key to enter System Control System Control submenu Only set sub Analog datum setting Press V+ key to enter Min/Max Control brightness of picture and sound submenu Bri Mid White balance Press V+ key to enter White Balance parameters setting submenu Press V+ key to enter Used for hotel TV Hotel Option Hotel mode submenu EPROM data EPROM Edit No setting editing Register Edit Register No setting

41

Use P+and P-keys on remote control to make up or down option, and useV+ andV-keys to set. Contents of sub pages Panel Control Setting item LVDS Mapping Backlight SavePower1 SavePower2 BL-invisible Panel type Factory Setting Setting item Balance Volume IIS Def Country RTC En CANAL-Visual TunnerSelect Factory Out System Control Setting item Default Lang L/L AGC OverModulation PreScl SCART PreScl AM (or PreScl Mono for America) PreScl FM (or PreScl stereo for America) PreScl NICAM (or PreScl SAP for America) EQ-invisible ATS Logo Logo Edit Setting value English 5 On/Off 8 12 Remark Default OSD language L/L sound AGC OverModulation switch SCART L/R input amplitude prescale AM_MONO IF prescale (Mono IF prescalar) FM_MONO IF prescale (Stereo IF prescale) NICAM sound IF prescale (SAP IF prescale) Equalizer switch Off is 5 section equalization On is high/low pitch setting Program auto sequencing switch Starting blue background LOGO switch LOGO display contents V+ V-for choosing setting position, P+ P-for choosing letter including 52 English
42

Setting value 0x09 100 50 30 Off CMO

Remark Polarity of LVDS signal Back light brightness value 1 Back light brightness value 2 Back light brightness value 3 Show SavePower mode in menu or not ONnot showOFFshow Choose the type of the LCD screen to get the right parameter

Setting value -50_0_50 0_10_20_100 On/Off Other On/Off On/Off XG >>

Remark Fast check of the balance of L/R sound channel Fast setting of volumeeach step is 10 Preset sound decoding IC of HDMI Default country Show real time clock or not Open Canal+ function to user or not Choose the type of Tuner (Europe market only) Output the factory settings

Setting item SSC Delta Positive Negative Write

Setting value 0 6 6

12

19 Off Off Off

big/small letters together Logo Colour Min/Max Control Setting item Con Min Con Mid Con Max Bri Min Bri Mid Bri Max Col Min Col Mid Col Max Tnt Min Tnt Mid Tnt Max Shp Min Shp Mid Shp Max White Balance Normal R Gain G Gain B Gain R Offset G Offset B Offset Cool R Gain G Gain B Gain R Offset G Offset B Offset Hotel Option Setting item Hotel Mode Enable Setting value No Remark Hotel mode presettingYesusers can enter into Hotel modeNousers cant enter into Hotel mode No use 7DH 80H 9AH 80H 80H 74H 7DH 80H 9AH 80H 80H 90H Warm R Gain G Gain B Gain R Offset G Offset B Offset 7DH 80H 9AH 84H 80H 74H Setting value 30H 70H A2H 00H 8DH A0H 00H 40H 70H 20H 80H E0H 00H 60H A0H Setting item Vol Min Vol Mid 1 Vol Mid 2 Vol Mid 3 Vol Mid 4 Vol Max Tre Min Tre Mid Tre Max Bas Min Bas Mid Bas Max Setting value 00H 01H 14H 28H 4BH 64H 00H 30H 60H 00H 30H 60H Logo colour Modified according to users require

Force Pos 00 Notes A. InMin/Max CONTROL setting item, Bri Miditem is used to set sub brightness of picture; B. White balance needs to be set in Normalmode;
43

C. Set CLEAR EPROM will clear the memory data, So do not set it unless it is needed; other setting items do not need setting. 2. Setting method of factory menu Choose setting item Operators can choose setting item orderly with P+ and P- key, font having background display represents the item has been chosen. PressV+key to enter sub directory. Use P+and P-keys on remote control to make up or down option, and useV+and V-keys to set. (2)All the menu functions are opened in factory mode, item checking and effect testing can be done by using menu if it is needed. (3)Switching TV signal in factory mode can be done by directly pressing the number key. Press MENU key to back to the parent of working directory, press DISPLAY key to quit factory mode.

Appendix 1 LS01 module taking LT32GJ01E for example Circuit Schematic Diagram(see next page)

44

45

46

47

48

49

50

Appendix 2 Power Module Schematic Diagram

51

Final Assembly Diagram LT2618

52

53