Diesel Engine Management

Diesel Engine Management Systems Index Diesel Engine Management Systems Index
Diesel Engine management component descriptions Bosch Common rail Bosch in-line with EDC Bosch VE with EDC Bosch VP & VR Lucas DPC-N & DPI-N Lucas EPIC Toyota ECD - Denso Lucas Unit injector Safety precautions Tools & equipment Oscilloscope testing
Page 1 of 56
Diesel Engine management component descriptions

Engine control module (ECM) Fuel supply system Load sensing Idle speed control Sensors Engine speed & position sensors Valves Cold starting equipment
Engine control module (ECM)

Electrical signals from engine and vehicle sensors are received and processed by the electronic circuits in the ECM. Functions Input signals are received from some or all of the following:
l l l l l l l l
Accelerator position (APP) sensor. Fuel lever position sensor. Injector needle lift sensor. Fuel temperature sensor. Engine coolant temperature (ECT) sensor. Intake air temperature (IAT) sensor. Throttle position (TP) sensor. Load sensor - mass air flow (MAF) sensor or manifold absolute pressure (MAP) sensor.
file://C:\Documents and Settings\KEN\Local Settings\Temp\~hhDEDF.htm
10/11/2005
Diesel Engine Management Systems Index

l l l l l
Page 2 of 56
Vehicle speed (VSS) sensor. Crankshaft position (CKP) sensor. Engine speed (RPM) sensor. Barometric pressure (BARO) sensor. Immobilizer control module.
Outputs from the ECM control some or all of the following:

l l l l l l l l l l l l
Injectors (electrical type only) - by controlling the length of time each injector remains open. Fuel pump relay. Fuel injection timing solenoid. Fuel quantity adjuster. Fuel pressure control solenoid. Idle speed control system. Exhaust gas recirculation system. Turbocharger (TC) wastegate regulating valve. Intake manifold air control solenoid. Glow plug relay. Glow plug warning lamp. Self-diagnosis of faults, indicated by a malfunction indicator lamp (MIL) or check engine warning light on the instrument panel Fig. 1. Emergency 'limp-home' programme, which substitutes an average value for certain sensors enabling the vehicle to be driven to a workshop for correction.
Fig. 1
Fuel supply system

Fuel pressure regulator - Common rail
Maintains an even supply pressure to the injectors. Located in the high-pressure pump or the fuel rail. Fig. 2
10/11/2005
Page 3 of 56
1. 2. 3. 4. 5. 6. 7. 8.
Solenoid Spring Magnetic core Pressurised fuel inlet Ball valve Fuel outlet to common rail Fuel return Electrical connector
Operation
l
A ball-type valve separates the high-pressure fuel supply from the fuel return circuit. The valve remains closed under pressure from the high-pressure supply pump. When the solenoid is energised the magnetic core pushes the ball valve off its seat and allows the excess fuel to flow back to the tank. The regulator is continually switched on and off (cycled) by the engine control module (ECM) and the delivery pressure is dependent on the duty cycle.
Fuel pressure regulator - unit injector

Located in the fuel supply housing on the cylinder head. Fig. 3
10/11/2005
Page 4 of 56
1. 2. 3. 4. 5.
Pre-set regulator Circlip 'O' ring 'O' ring Regulator housing
Operation
l
The pressure regulator consists of a spring-loaded regulator that acts on a valve in the regulator housing. When the fuel supply pressure exceeds the preset regulator pressure the valve opens and allows the excess fuel to flow back to the tank.
Injectors - mechanical type

Operation
l
Fuel is delivered to the high-pressure connection at the commencement of injection. The pressure acts against the injector spring pressure and lifts the needle from its seat. Atomized fuel is sprayed from the nozzle into the engine swirl or combustion chamber.
Fig. 4
10/11/2005
Page 5 of 56
1. 2. 3. 4. 5. 6. 7.
Fuel return connection Compression spring Body Cap nut/nozzle holder Nozzle needle Pintle Shim
Injectors - mechanical type, with needle lift sensor

Operation
l
This injector operates in the same way as in Fig. 4, but has an integral inductive sensor. At the commencement of injection the magnetic setting pin moves upwards and induces an alternating current into the sensor windings. This information, together with signals from the crankshaft position (CKP) sensor, is used by the engine control module (ECM) to measure the injection timing.
Fig. 5
10/11/2005
Page 6 of 56
1. 2. 3. 4.
Setting pin Sensor winding Pressure pin Electrical connector
Injectors - electrical type

Operation
l
Electronically controlled injectors are supplied with a constant supply of fuel at high pressure. A solenoid operated ball-type valve separates the control chamber from the return circuit and ensures that the needle is held on its seat by the injector spring. At the commencement of injection the solenoid is energised and the ball valve opens allowing the pressure in the control chamber to fall. The pressure in the pressure chamber acts against the injector spring and lifts the needle from its seat. Atomized fuel is sprayed from the nozzle into the engine combustion chamber. To reduce the high current required to operate the injector, the engine control module (ECM) rapidly switches the solenoid during the opening duration.
Fig. 6
10/11/2005
Page 7 of 56
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11.
Solenoid Fuel inlet Fuel return Electrical connector Control chamber Pressure chamber Injector needle Injector spring Control piston Ball valve 1Return nozzle
Unit injector
Operation Fuel is supplied at a regulated pressure to the injector by an electrical fuel lift pump. The solenoid is energised by the engine control module (ECM) and the spill port is closed. As the engine rotates, the engine camshaft pressurises the fuel in the unit injector. The pressure acts against the injector spring pressure and lifts the needle from its seat. Atomized fuel is sprayed from the nozzle into the engine combustion chamber. When the correct
10/11/2005
Page 8 of 56
quantity of fuel has been injected the solenoid is de-energised, the spill port opens and allows excess fuel to return to the fuel tank. The unit injectors use low resistance solenoids. To reduce the current being switched by the ECM, the voltage is rapidly switched during the injection period. Fig. 7
1. 2. 3. 4. 5. 6. 7. 8. 9.
Fuel inlet Fuel return Injector Injector spring Pump plunger Pushrod Pushrod return spring Solenoid Solenoid valve
Load sensing
Mass air flow (MAF) sensor - hot-wire type
The MAF sensor has no moving parts and provides very little restriction to the air flow. It is fitted between the air filter and intake manifold. Operation
l l l
The MAF sensor consists of a venturi with a resistance wire exposed to the incoming air. An air temperature sensor or compensating wire is also exposed to the air flow. The engine control module (ECM) senses changes in temperature caused by variations in air mass passing through the sensor body and increases or decreases the current flowing through the measuring wire. An internal electronic circuit maintains the approximate temperature of the measuring wire at a constant 120C above the intake air temperature. As the mass of air passing the wire increases, so the current required to maintain the temperature also increases.
10/11/2005

l
Page 9 of 56
This increase in current is sensed by the ECM.
Fig. 8
1. 2. 3. 4.
Protective mesh Resistance wire Intake air Compensating wire
Mass air flow (MAF) sensor - hot-film type

Similar to the hot-wire type, but with the measuring element incorporated in a ceramic plate.
Manifold absolute pressure (MAP) sensor

l
Fitted to the intake manifold or located in the engine bay and connected by vacuum hose.
Operation
l
The sensor consists of a diaphragm and piezo-electric circuit which varies the resistance in proportion to the pressure in the manifold. The sensor has a 5 volt supply and sends a signal voltage to the ECM which is proportional to the manifold pressure. The ECM uses the voltage signals from the MAP sensor to monitor turbocharger (TC) boost pressure and adjust fuel injection quantity and timing.
Fig. 9
10/11/2005
Page 10 of 56
A. B. 1. 2. 3.
Full load Idling Vacuum connector Piezo-electric crystal Electrical connections
Idle speed control

Idle speed control (ISC) actuator
The ISC actuator is used in conjunction with mechanical fuel injection pumps and allows the idle speed to be controlled to suit all operating conditions. Fig. 10
1.
Idle speed control (ISC) actuator
10/11/2005

2. Operating cable
Page 11 of 56
Operation
l
The device consists of a reversible electric motor-driven geartrain, acting on an operating cable attached to the idle lever of the injection pump. The ECM monitors the engine speed and if necessary the motor is energised to either extend or shorten the cable. The actuator also incorporates a switch to confirm its fully retracted position.
Sensors
Accelerator position (APP) sensor
The APP sensor can comprise of a potentiometer, idle and/or full load switch, or an electronic circuit. The APP sensor can be mounted on the accelerator pedal bracket and operated directly, or operated by a cable and located in the engine bay. Signals from the APP sensor are used by the ECM to determine the exact accelerator position. Fig. 11
1. 2. 3.
Potentiometer and idle/full load switch Spring Shaft
Engine coolant/intake air temperature sensor

The engine coolant (ECT) sensor probe is immersed in coolant and changes its resistance in proportion to engine coolant temperature changes. The intake air temperature (IAT) sensor probe is either incorporated in the mass air flow (MAF) sensor or is mounted in the air stream of the intake system. Its resistance changes in proportion to intake air temperature changes. Fig. 12
10/11/2005
Page 12 of 56
1. 2. 3.
Electrical connections Housing NTC resistor
Operation
l
In most cases the sensor incorporates a negative temperature coefficient (NTC) resistor, which decreases in resistance as the temperature rises.
Engine speed and position sensors

Engine speed (RPM), crankshaft position (CKP) and camshaft position (CMP) sensors are of two basic types, inductive or Hall effect. CMP sensors may be mounted on the camshaft housing or cylinder head, CKP sensors may be mounted on the crankcase or bell housing.
Inductive type
These sensors contain a permanent magnet partly enclosed in a soft iron core and partly in a field winding. The tip of the sensor is positioned close to the flywheel ring gear, a separate toothed trigger wheel, or a toothed wheel attached to the crankshaft pulley. In certain applications the sensor(s) are incorporated in the fuel injection pump. Fig. 13
10/11/2005
Page 13 of 56
1. 2. 3. 4. 5.
Soft iron core Field winding Permanent magnet Flywheel ring gear TDC pin
Operation
l
As the teeth or pins of the trigger wheel pass the sensor the magnetic field changes, inducing a voltage signal which is sent to the engine control module (ECM).
Hall-effect type
The Hall effect sensor consists of a semi-conductor material, through which a current flows, enclosed by a magnetic field at right angles to the current flow. Fig. 14
1. 2.
Sensor Electrical connector
10/11/2005

Operation
l
Page 14 of 56
The trigger wheel Fig. 15 [1] rotates allowing a magnetic field to pass between the sensor's magnet poles when aligned Fig. 15 [2] . This magnetic field is used to control the flow of current through a semiconductor which then operates an integral control circuit. The sensor is supplied with a control current from the ECM which is switched to earth as the sensor operates generating a square wave signal.
Fig. 15
Throttle position (TP) sensor

The throttle position sensor is a variable resistance (potentiometer) connected to the throttle valve shaft. Fig. 16
1. 2. 3.
Throttle butterfly shaft Wiper arm Resistance tracks
10/11/2005

Operation
l
Page 15 of 56
It is supplied with a reference voltage and the output signal voltage is used by the ECM to interpret the exact throttle position.
Valves
Exhaust gas recirculation (EGR) valve
To reduce the oxides of nitrogen emitted by the exhaust, a proportion of the exhaust gas can be returned to the inlet manifold when operating conditions allow. Operation
l
The exhaust gas recirculation valve is operated by a vacuum-controlled solenoid -operated modulator valve. The duty cycle is varied according to the operating conditions to control the flow of exhaust gas into the inlet manifold.
Fig. 17
Turbocharger (TC) wastegate regulating valve

The turbocharger boost pressure can be controlled by the engine control module (ECM) with a solenoid -operated modulator valve. Signals from the manifold absolute pressure (MAP) sensor are monitored and the maximum boost pressure controlled. Fig. 18
10/11/2005
Page 16 of 56
Operation
l
The turbocharger wastegate actuator is operated by a vacuum-controlled solenoid-operated modulator valve (turbocharger wastegate regulating valve). The duty cycle is varied according to the operating conditions to control the maximum boost pressure.
Cold starting equipment

Glow plugs
To enable the engine to be started in low temperatures glow plugs are used to raise the temperature in the combustion chambers (pre-heating). The glow plugs can also be used during cold running to reduce harmful exhaust emissions, blue smoke and knocking (post-heating). Although the pre-heating and post-heating can be controlled by a dedicated glow plug control unit, it is more common on modern systems to be controlled by the engine control module (ECM). Fig. 19
10/11/2005

1. 2. 3. 4. 5. 6. 7. Terminal Insulator Casing Element seal Heater and control coils Glow tube Powder
Page 17 of 56
Operation
l
The glow plug comprises heater and control coils embedded in magnesium-oxide powder. When voltage is applied to the terminal current flows through the heating elements and the temperature rapidly rises. Current also flows through the control coils and this produces heat but at a slower rate. The resistance rises as the temperature increases at the tip to approximately 1200C. The glow plugs can remain energised after starting (post-heating), when cold until the engine coolant temperature reaches a predetermined point, or for a maximum time in the region of 180 seconds.
Bosch Common rail

Fuel injection system components Fig. 1
1. 2. 3. 4. 5. 6.
3rd piston cut-off solenoid Accelerator position (APP) sensor Battery Crankshaft position (CKP) sensor Engine control module (ECM) Engine coolant temperature (ECT) sensor
10/11/2005

7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. Exhaust gas recirculation (EGR) solenoid Fuel cooler Fuel filter Fuel heater Fuel injector Fuel lift pump (electrical) Fuel lift pump (mechanical) Fuel lift pump relay Fuel pressure control solenoid Fuel pressure sensor Fuel rail Fuel shut-off solenoid Fuel tank Fuel temperature sensor Glow plug relay Glow plug Glow plug warning lamp High-pressure fuel pump Ignition switch Intake air temperature (IAT) sensor Malfunction indicator lamp (MIL) Manifold absolute pressure (MAP) sensor Mass air flow (MAF) sensor Turbocharger (TC) wastegate regulating valve Vehicle speed sensor (VSS)
Page 18 of 56
System operation The Bosch Common rail system uses the latest diesel injection technology. The fuel injection quantity and timing together with control of exhaust emissions are electronically controlled. Signals from the accelerator pedal position (APP) sensor [2] together with information from other engine and vehicle sensors are transmitted to the engine control module (ECM) [5] . An electrical fuel pump [12] or an engine driven mechanical pump [13] or both supply fuel at low pressure to the high pressure pump. The high-pressure fuel supply is provided by an engine-driven mechanical high-pressure pump [24]. The pump comprises three pumping elements driven by an eccentric shaft. The pressure is controlled by a fuel pressure control solenoid [15] mounted on the rear of the pump. On some applications a 3rd piston cut-off solenoid [1] is used to enable the pump to operate only two pumping elements, resulting in less engine power being absorbed at low engine loads. High-pressure fuel from the high-pressure fuel pump is delivered to the fuel rail [17] where it is distributed to the injectors [11]. Operating conditions in the fuel rail are monitored by the fuel temperature sensor [20] and fuel pressure sensor [16]. The fuel injectors are electrically operated by the ECM [5] and use low -resistance solenoids. To reduce the current being switched by the ECM, the voltage is rapidly switched during the injection period. The fuel is injected in two stages (or three where exhaust emission standards are higher), firstly the PILOT injection to precondition the combustion chamber, followed very shortly afterwards by the MAIN injection. Some applications where higher exhaust emission standards are required use a third period of injection called POST injection, where fuel is injected into the exhaust stroke and reburnt via the exhaust gas recirculation (EGR) system.
10/11/2005
Diesel Engine Management Systems Index Bosch in -line with EDC

Page 19 of 56
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19.
Accelerator position (APP) sensor Battery Crankshaft position (CKP) sensor Engine control module (ECM) Engine coolant temperature (ECT) sensor Exhaust gas recirculation (EGR) solenoid Fuel filter Fuel injection pump Fuel injector Fuel tank Glow plug relay Glow plug Glow plug warning lamp Ignition switch Intake air temperature (IAT) sensor Malfunction indicator lamp (MIL) Manifold absolute pressure (MAP) sensor Turbocharger (TC) wastegate regulating valve Vehicle speed sensor (VSS)
Injection pump operation
10/11/2005

Fig. 2
Page 20 of 56
1. 2. 3. 4. 5. 6.
Low-pressure plunger-type pump High-pressure pump plunger Delivery valve holder Fuel quantity adjuster Control rod Fuel shut-off solenoid
The Bosch in-line fuel injection pump has been used by many vehicle manufacturers in cars and commercial vehicles for many years. The pump is driven at engine camshaft speed via gears or chain. Fuel is supplied to the injection pump by an integral low-pressure plunger-type pump [1]. Excess fuel is allowed to drain from the injection pump via the overflow restriction in the pump return connection. Fuel is pressurised by the high-pressure pump plunger [2] and delivered to the injectors at high pressure via the delivery valve holder [3] . Unlike the earlier version, the Electronic Diesel Control (EDC) in-line pump uses computer technology to control fuel injection quantity. The fuel injection quantity is controlled by an electrical actuator (fuel quantity adjuster) [4] acting on the control rod [5] , and its position is monitored by an integral quantity adjuster position sensor. A crankshaft position (CKP) sensor is used to monitor engine speed which allows closed-loop control. The fuel injection timing is controlled by a mechanical unit integral to the fuel injection pump drive gear or sprocket. Signals from the accelerator pedal position (APP) sensor together with information from other engine and vehicle sensors are used by the engine control module (ECM) to calculate the fuel injection quantity. When the ignition is in the OFF position (or if the vehicle immobilizer is not deactivated), the fuel quantity adjuster will return to the position of zero fuel quantity and the engine will stop. To ensure that the engine can be stopped in the event of a fault in the control system or actuator, a fuel shut-off solenoid [6] is retained.
Bosch VE with EDC
10/11/2005

Page 21 of 56
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17.
Accelerator position (APP) sensor Battery Crankshaft position (CKP) sensor Engine control module (ECM) Engine coolant temperature (ECT) sensor Exhaust gas recirculation (EGR) solenoid Fuel filter Fuel injection pump Fuel injector (with needle lift sensor) Fuel tank Glow plug relay Glow plug Glow plug warning lamp Ignition switch Malfunction indicator lamp (MIL) Mass air flow (MAF) sensor Vehicle speed sensor (VSS)
Injection pump operation Fig. 2
10/11/2005
Page 22 of 56
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.
Vane-type low-pressure pump Return connection Distributor plunger Distributor head Fuel quantity adjuster Control collar Fuel quantity adjuster position sensor Fuel injection timing solenoid Timing actuator Roller ring Fuel shut-off solenoid Fuel temperature sensor
The Bosch VE rotary fuel injection pump has been used by many vehicle manufacturers in cars and light commercial vehicles for many years. The pump is driven at engine camshaft speed either via gears, chain or toothed belt. Fuel is drawn into the injection pump by a vane-type low-pressure pump [1] and the pump internal pressure is regulated by a pressure control valve. Excess fuel is allowed to drain from the injection pump via the overflow restriction in the return connection [2] . Fuel is pressurised by the distributor plunger [3] and delivered to the injectors at high pressure via the distributor head [4] . Unlike the earlier version, the Electronic Diesel Control (EDC) VE pump uses computer technology to control fuel injection quantity and timing. The fuel injection quantity is controlled by an electrical actuator (fuel quantity adjuster) [5] acting on the control collar [6] , and its position is monitored by the quantity adjuster position sensor [7] which allows closed-loop control. The fuel injection timing is controlled by the fuel injection timing solenoid [8] , which regulates the control pressure acting on the timing actuator [9]. The timing actuator varies the position of the roller ring [10]. A crankshaft position (CKP) sensor and an injector needle lift sensor are used to monitor the actual injection timing which allows closed-loop control. Signals from the accelerator pedal position (APP) sensor together with information from other engine and vehicle sensors are used by the engine control module (ECM) to calculate the fuel quantity and injection timing. When the ignition is in the OFF position (or if the vehicle immobilizer is not deactivated), the fuel quantity adjuster will return to the position of zero fuel quantity and the engine will stop.
10/11/2005
Page 23 of 56
To ensure that the engine can be stopped in the event of a fault in the control system or actuator, a fuel shut-off solenoid [11] is retained.
Bosch VP & VR
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19.
Accelerator position (APP) sensor Battery Crankshaft position (CKP) sensor Engine control module (ECM) Engine coolant temperature (ECT) sensor Exhaust gas recirculation (EGR) solenoid Fuel filter Fuel injection pump Fuel injector (with needle lift sensor) Fuel lift pump Fuel lift pump relay Fuel tank Glow plug relay Glow plug Glow plug warning lamp Ignition switch Intake air temperature (IAT) sensor Malfunction indicator lamp (MIL) Manifold absolute pressure (MAP) sensor
10/11/2005

20. 21. 22. Mass air flow (MAF) sensor Turbocharger (TC) wastegate regulating valve Vehicle speed sensor (VSS)
Page 24 of 56
1. 2. 3. 4. 5. 6. 7. 8. 9.
Fig. 2
Vane-type low-pressure pump High-pressure plungers Distributor head Fuel injection pump control module Fuel quantity adjuster Fuel injection timing solenoid Timing actuator Cam ring Injection pump position sensor
10/11/2005

1. 2. 3. 4. 5. 6. 7. 8. 9. Vane-type low-pressure pump Distributor plunger Distributor head Fuel injection pump control module Fuel quantity adjuster Fuel injection timing solenoid Timing actuator Cam ring Injection pump position sensor
Page 25 of 56
This Bosch rotary fuel injection pump is available with either radial (VR-type pump) Fig. 2 or axial (VP-type pump) Fig. 3 high-pressure pumping elements. Both pumps uses computer technology to control fuel injection quantity and timing. The pump is driven at engine camshaft speed either via gears, chain or toothed belt. NOTE: Damage may occur to the injection pump if it is operated without an adequate fuel supply. Refer to the manufacturers instructions when changing fuel filters or opening the fuel lines. Fuel is drawn into the injection pump by a vane-type low-pressure pump Fig. 2 [1] & Fig. 3 [1] and the pump internal pressure is regulated by a pressure control valve. Excess fuel is allowed to drain from the injection pump via the overflow restriction in the return connection. In the radial-type (VR) pump Fig. 2 , fuel is pressurised by the two high pressure plungers Fig. 2 [2] and delivered to the injectors at high pressure via the distributor head Fig. 2 [3]. In the axial-type (VP) pump Fig. 3 , fuel is pressurised by the distributor plunger Fig. 3 [2] and delivered to the injectors at high-pressure via the distributor head Fig. 3 [3] . Signals from the accelerator pedal position (APP) sensor together with information from other engine and vehicle sensors are transmitted to the engine control module (ECM). Signals from sensors mounted in the injection pump are transmitted to the fuel injection pump control module Fig. 2 [4] & Fig. 3 [4] mounted on the injection pump. The two control modules communicate by a CAN data bus system enabling the calculation of the fuel quantity and injection timing. The fuel injection quantity is controlled by a solenoid (fuel quantity adjuster) Fig. 2 [5] & Fig. 3 [5]. The fuel quantity adjuster is energised during the pressure stroke until the calculated quantity of fuel has been injected. The fuel quantity adjuster is then de-energised allowing excess fuel to be diverted to the return circuit. The fuel injection timing is controlled by the fuel injection timing solenoid Fig. 2 [6] & Fig. 3 [6] , which regulates the control pressure acting on the timing actuator Fig. 2 [7] & Fig. 3 [7]. The timing actuator varies the position of the cam ring Fig. 2 [8] & Fig. 3 [8] . An injection pump position sensor Fig. 2 [9] & Fig. 3 [9] mounted in the injection pump together with a crankshaft position (CKP) sensor and an injector needle lift sensor are used to monitor the actual injection timing which allows closed-loop control. When the ignition is in the OFF position (or if the vehicle immobilizer is not deactivated), the fuel quantity adjuster will remain de-energised (zero fuel quantity) and the engine will stop
Lucas DPC-N & DPI-N

10/11/2005
Page 26 of 56
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18.
Battery Crankshaft position (CKP) sensor Engine control module (ECM) Engine coolant temperature (ECT) sensor Exhaust gas recirculation (EGR) solenoid Fuel filter Fuel injection pump Fuel injector (with needle lift sensor) Fuel tank Glow plug relay Glow plug Glow plug warning lamp Ignition switch Intake air temperature (IAT) sensor Malfunction indicator lamp (MIL) Mass air flow (MAF) sensor Turbocharger (TC) wastegate regulating valve Vehicle speed sensor (VSS)
10/11/2005
Page 27 of 56
1. 2. 3. 4. 5. 6. 7. 8.
Vane-type low-pressure pump High-pressure plungers Distributor head Fuel injection timing solenoid Timing actuator Cam ring Fuel lever position sensor Fuel shut-off solenoid
The Lucas DPC rotary fuel injection pump has been used by many vehicle manufacturers in cars and light commercial vehicles for many years. The pump is driven at engine camshaft speed either via gears, chain or toothed belt. Fuel is drawn into the injection pump by a vane-type low-pressure pump [1] and the pump internal pressure is regulated by a pressure control valve. Excess fuel is allowed to drain from the injection pump via the overflow restriction in the return connection. Fuel is pressurised by the two high-pressure plungers [2] and delivered to the injectors at high pressure via the distributor head [3] . The fuel injection quantity is controlled by a mechanical governor. Unlike the earlier DPC injection pump, the DPC-N and DPI-N (N = Numeric) pumps use computer technology to control fuel injection timing. The fuel injection timing is controlled by the fuel injection timing solenoid [4] , which regulates the control pressure acting on the timing actuator [5]. The timing actuator varies the position of the cam ring [6] . A crankshaft position (CKP) sensor and an injector needle lift sensor are used to monitor the actual injection timing which allows closed-loop control. Signals from the fuel lever position sensor [7] , together with information from other engine and vehicle sensors are used by the engine control module (ECM) to calculate the fuel injection timing. When the ignition is switched OFF (or if the vehicle immobilizer is not deactivated), the fuel shut-off solenoid [8] will return to the closed position and the engine will stop.
Lucas EPIC
Fuel injection system components
10/11/2005

Fig. 1
Page 28 of 56
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18.
Accelerator position (APP) sensor Battery Crankshaft position (CKP) sensor Engine control module (ECM) Engine coolant temperature (ECT) sensor Exhaust gas recirculation (EGR) solenoid Fuel filter Fuel injection pump Fuel injector (with needle lift sensor) Fuel tank Glow plug relay Glow plug Glow plug warning lamp Ignition switch Intake air temperature (IAT) sensor Malfunction indicator lamp (MIL) Manifold absolute pressure (MAP) sensor Vehicle speed sensor (VSS)
10/11/2005
Page 29 of 56
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15.
Vane-type low-pressure pump Pressure control valve Fuel return connection Distributor plungers Distributor head Fuel quantity adjusters Rotor cavity Rotor Injection pump rotor position sensor Injection timing solenoid Timing actuator Cam ring Injection pump cam ring position sensor Injection pump position sensor Fuel shut-off solenoid
The Lucas EPIC is a fully electronically controlled rotary fuel injection pump. It is used by many vehicle manufacturers in cars and light commercial vehicles. The pump is driven at engine camshaft speed either via gears, chain or toothed belt. Fuel is drawn into the injection pump by a vane-type low-pressure pump [1] and the pump internal pressure is regulated by a pressure control valve [2]. Excess fuel is allowed to drain from the injection pump via the fuel return connection [3]. Fuel is pressurised by the distributor plungers [4] and delivered to the injectors at high pressure via the distributor head [5] . The fuel injection quantity is controlled by two solenoids (fuel quantity adjusters) [6] . The solenoids act on valves controlling the flow of fuel into (feed valve) and out of (drain valve) the cavity at the end of the rotor [7]. When the feed valve is opened the rotor [8] is forced against spring pressure and moves towards the front of the pump (minimum fuel position). When the drain valve is opened the spring forces the rotor towards the rear of the pump (maximum fuel position). The solenoids are continually switched to control fuel injection quantity. Closed-loop control of the rotor position is maintained with the use of a rotor position sensor mounted at the rear of the pump [9] . The fuel injection timing is controlled by the fuel injection timing solenoid [10] . The solenoid acts on a valve controlling the
10/11/2005

flow of fuel to the timing actuator [11]. The timing actuator varies the position of the cam ring [12].
Page 30 of 56
Closed-loop control of the cam ring position is maintained with the use of an injection pump cam ring position sensor mounted on the side of the pump [13]. A crankshaft position (CKP) sensor, and either an injector needle lift sensor or an injection pump position sensor [14] are used to monitor the actual injection timing. Signals from the accelerator pedal position (APP) sensor together with information from other engine and vehicle sensors are used by the engine control module (ECM) to calculate the fuel quantity and injection timing. When the ignition is in the OFF position (or if the vehicle immobilizer is not deactivated), the fuel shut-off solenoid [15] will be de-energised and the engine will stop.
Toyota ECD - Denso

1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
Accelerator position (APP) sensor Battery Crankshaft position (CKP) sensor Engine control module (ECM) Engine coolant temperature (ECT) sensor Exhaust gas recirculation (EGR) solenoid Fuel filter Fuel injection pump Fuel injector Fuel tank
10/11/2005

11. 12. 13. 14. 15. 16. 17. 18. 19. Glow plug relay Glow plug Glow plug warning lamp Ignition switch Intake air temperature (IAT) sensor Malfunction indicator lamp (MIL) Manifold absolute pressure (MAP) sensor Turbocharger (TC) wastegate regulating valve Vehicle speed sensor (VSS)
Page 31 of 56
1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
Inlet connection Pressure control valve Return overflow valve Distributor head Fuel quantity adjuster Fuel injection timing solenoid Timing actuator Injection pump position sensor Module coding plug Fuel temperature sensor
The Denso rotary fuel injection pump is of the axial type and has been used by many Asian vehicle manufacturers in cars and light commercial vehicles for many years. The pump is driven at engine camshaft speed either via gears, chain or toothed belt. Fuel is drawn into the injection pump by a vane-type low-pressure pump at the inlet connection [1], and the pump internal pressure is regulated by a pressure control valve [2] . Excess fuel is allowed to drain from the injection pump via the return overflow valve in the return connection [3]. Fuel is pressurised by the distributor plunger and delivered to the injectors at high pressure via the distributor head [4] .
10/11/2005
Page 32 of 56
Unlike the earlier version, the electronic control diesel (ECD) pump uses computer technology to control fuel injection quantity and timing. The fuel injection quantity is controlled by an electrical solenoid (fuel quantity adjuster) [5] which is continually switched by the engine control module (ECM). The fuel injection timing is controlled by the fuel injection timing solenoid [6] , which regulates the control pressure acting on the timing actuator [7]. The timing actuator varies the position of the roller ring. An injection pump position sensor [8] , (which also gives pump speed information), together with a crankshaft position (CKP) sensor are used to monitor the actual injection timing which allows closed-loop control. A module coding plug [9] is used to correct manufacturing variations between injection pumps. Signals from the accelerator pedal position (APP) sensor together with information from other engine and vehicle sensors are used by the ECM to calculate the fuel quantity and injection timing. When the ignition is in the OFF position (or if the vehicle immobilizer is not deactivated), the fuel quantity adjuster will return to the position of zero fuel quantity and the engine will stop.
Lucas Unit injector

1. 2. 3. 4. 5. 6.
Accelerator position (APP) sensor Battery Crankshaft position (CKP) sensor Engine control module (ECM) Engine control relay Engine coolant temperature (ECT) sensor
10/11/2005

7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. Exhaust gas recirculation (EGR) solenoid Fuel cooler Fuel filter Unit injector Fuel lift pump Fuel lift pump relay Fuel pressure regulator Fuel tank Fuel temperature sensor Glow plug relay Glow plug Glow plug warning lamp Ignition switch Intake air temperature (IAT) sensor Malfunction indicator lamp (MIL) Manifold absolute pressure (MAP) sensor Mass air flow (MAF) sensor Turbocharger (TC) wastegate regulating valve Vehicle speed sensor (VSS)
Page 33 of 56
System operation Fig. 2
1. 2. 3. 4. 5. 6. 7. 8. 9.
Fuel inlet Fuel return Injector Injector spring Pump plunger Pushrod Pushrod return spring Solenoid Solenoid valve
The unit injector system has been used on diesel engines for many years. The injectors are mechanically operated and until recently the system has been used mainly for large commercial vehicles, marine applications and stationary engines.
10/11/2005
Page 34 of 56
The latest systems, now being used for smaller engines, use computer technology to control the injectors Fig. 2 . Signals from the accelerator pedal position (APP) sensor Fig. 1 [1] together with information from other engine and vehicle sensors are transmitted to the engine control module (ECM) Fig. 1 [4] . A two-stage electrical fuel lift pump Fig. 1 [11] supplies fuel via a fuel filter Fig. 1 [9] to the fuel pressure regulator Fig. 1 [13]. Fuel at a regulated pressure (approximately 4 bar) is supplied to the unit injector and the excess is allowed to return to the fuel tank after its temperature is lowered by the fuel cooler Fig. 1 [8]. As the engine rotates, the engine camshaft pressurises the fuel in the unit injector to approximately 1500 bar. The unit injectors Fig. 2 are electrically operated by the engine ECM Fig. 1 [4] and use low resistance solenoids. To reduce the current being switched by the ECM, the voltage is rapidly switched during the injection period. The pump plunger is depressed by the camshaft, and at a point determined by the ECM the solenoid valve is energised closing the spill port. Pressure rises until the injector needle is forced from its seat and injection takes place. After the injection period the solenoid valve is de-energised and the rotation of the camshaft releases the pump plunger allowing cool fuel to replenish the injector in readiness for the next cycle.
Safety precautions
Airbags (Supplementary Restraint System - SRS) Electrical Mechanical
Airbags (Supplementary Restraint System - SRS)

Many of the models covered by this manual are fitted with airbags as standard equipment. When working on a vehicle fitted with such a system, extreme caution must be taken to avoid accidental firing of the airbag, which could result in personal injury. Unauthorised repairs to the system could render it inoperative, or cause it to inflate accidentally. NOTE: All related wiring may be encased in a yellow outer covering. When the engine is started the AIRBAG warning lamp should go out after approximately 5-10 seconds. If not this indicates a fault in the system. Refer to the Autodata manual Airbags & seat belt pretentioners.
l l l l
NEVER attempt to test the system using a multi -meter. NEVER tamper with or disconnect the airbag wiring harness. NEVER make extra connections to any part of the system wiring harness or terminals. ALWAYS ensure that the airbag wiring harness has not been trapped or damaged in any way when working on adjacent components or systems.
Electrical
l l
l l l
ALWAYS ensure that the battery is properly connected before attempting to start the engine. DO NOT attempt to start the engine using a source in excess of 12 volts, such as a fast charger (16 volts) or by connecting two batteries in series (24 volts). ALWAYS disconnect the battery before charging it. DO NOT disconnect the battery while the engine is running. DO NOT connect the battery with reverse polarity. DO NOT connect or disconnect the engine control module (ECM), or any other component of the diesel injection system while the ignition is switched ON. DO NOT disconnect ECM multi-plug within 30 seconds of switching ignition OFF.
10/11/2005

l
Page 35 of 56
l l
l l l
DO NOT connect or disconnect multi-meters, voltmeters, ammeters or ohmmeters with the ignition switched ON. DO NOT reverse the polarity of the fuel pump. ALWAYS ensure that all electrical connections are in good condition and making good contact, PARTICULARLY the ECM connector. ALWAYS disconnect the ECM, fuel pump relay/fuse before carrying out a compression test. DO NOT flash a wire or circuit to ground to check that continuity exists. ALWAYS ensure that any replacement electrical parts are correct for the application in question. Many units share common external features, but differ internally.
Mechanical
CAUTION: Do not connect pressure testing equipment to the fuel rail or other high pressure fuel system components of a common rail diesel injection system.
l
l l
DO NOT attempt to slacken any high pressure fuel pipe connections with the ignition on or the engine running. AVOID the risk of fire - NEVER work on the diesel injection system when SMOKING or close to a NAKED FLAME. ALWAYS keep a fire extinguisher close at hand when working on the diesel injection system. ALWAYS ensure that any replacement fuel system parts are correct for the application in question. Many units share common external features, but differ internally.
module (ECM) to calculate the fuel quantity and injection timing. When the ignition is in the OFF position (or if the vehicle immobilizer is not deactivated), the fuel shut-off solenoid [15] will be de-energised and the engine will stop.
Tools & equipment

Using multi-meters
General recommendations The majority of electrical tests described in this manual require the use of a digital multi -meter. Many suitable instruments are available, with a wide range of prices and specifications, as described below. Certain other tools, such as a breakout box or a digital oscilloscope (see separate section), will be necessary, or desirable to make best use of this manual. Breakout box
l l
Whenever possible a breakout box should be used for testing pinout signals. A breakout box [1] is a means of connecting test equipment to the ECM pins, without the need to probe into the back of the harness multi-plug. It is connected by an adaptor lead [2] , between the ECM [3] and the car's wiring harness [4] . The pin connections are laid out in rows in numerical order and have large connecting sockets, enabling test leads to be securely plugged into a circuit, and avoiding the possibility of connecting to the incorrect pin, due to miscounting. The possibility of damaging components or wiring, due to shorting live pins to ground or to other components, is also much reduced. The limiting factor is the range of adaptor leads. Several equipment manufacturers produce breakout boxes, but none are able to supply a complete range of leads to cover all the models included in this manual.
10/11/2005

Fig 1 - Breakout Box
Page 36 of 56
ECM harness multi-plug testing

l
l l
If a breakout box and suitable adaptor leads are not available, testing must be carried out at the wire side of the ECM harness multi -plug Fig. 2. To access the terminals the protective cover must be removed from the plug. Many different types of plug are used for engine management wiring harnesses and two examples are shown in Fig. 3 and Fig. 4. Use the appropriate ECM harness multi-plug - wire side diagram and identify the pin(s) to be tested. Use only very fine test probes to access the connections and measure the signal between the pin and earth Fig. 2 [1] , or between two ECM pins Fig. 2 [2], where a second pin number is given in brackets after the first number.
Fig 2 - ECM harness multi-plug testing
10/11/2005
Page 37 of 56
Multi-meters
l
A high impedance (10 K /volt minimum) multi-meter that includes a 0-20 V voltage scale and a low (0-200 ) and high (0-20 K ) range ohm scale is recommended for measuring the voltage and resistance of the system components. Analogue Fig. 5 and digital Fig. 6 electrical multi-test meters are available in a wide range of prices and specifications. In view of the fact that the instrument will be used in the harsh environment of the workshop, the extra expense of a shock-proof digital type will be a good investment. In addition to the usual volts, ohms and milliamp scales, features such as the facility to read frequency (Hz) and duty cycle (%), will also be useful.
Fig 5 - Analogue
10/11/2005
Page 38 of 56
Fig 6 - Digital
Using multi-meters
Voltage checking
l l l
Connect negative test lead to a good earth, or direct to the negative battery terminal. Observe conditions for test, e.g. ignition OFF, ignition ON etc. If the meter does not automatically select the appropriate voltage range, ensure correct meter scale selected, e.g. 0-12 volts. Connect positive test lead to ECM pin being tested.
Continuity checking
l l l
Ensure that battery supply voltage is not present at test terminals. Select appropriate resistance scale. Connect meter leads together and check zero reading (analogue meters only).
10/11/2005
Page 39 of 56
NOTE: If unable to zero meter, this usually indicates that the internal battery requires replacement.
l l
Connect ohmmeter leads to each end of component or wire to be tested. Read off resistance.
NOTE: If meter indicates zero Fig. 7 this indicates continuity between the two test points. If the meter indicates infinity Fig. 8, this indicates an open circuit (broken wire, burnt out component etc.) between the two test points. Fig 7 - Continuity indicated
Fig 8 - Open circuit indicated
Diode checking
l
l l
To check a diode connect the meter negative lead to the positive side of the diode and the positive lead to the negative side of the diode. The meter should indicate continuity Fig. 9. When the meter connections are reversed the meter should indicate an open circuit Fig. 10 . If continuity is indicated in each direction, the diode is faulty.
Fig 9 - Continuity indicated
10/11/2005
Page 40 of 56
Fig 10 - Open circuit indicated
Vacuum pump A hand operated vacuum pump, with gauge, will be necessary for testing certain components, such as manifold absolute pressure (MAP) sensors. Several types are available and are usually supplied with a connecting hose and a selection of adaptors Fig. 11. Fig 11 - Vacuum Pump
10/11/2005
Page 41 of 56
Memory savers With the increasing number of electronic devices incorporating a memory, whenever the battery is disconnected inconvenience is caused by the loss of such information as radio security codes and station settings, clock settings and ECM memories. This situation can be avoided by the use of an alternative power source such as the memory savers marketed by several of the leading test equipment manufacturers.
Oscilloscope testing
Why use an oscilloscope? Oscilloscope scales Wave forms Interpreting wave forms Component testing
Why use an oscilloscope?

l
Digital multi -meters are entirely satisfactory for checking circuits in a static condition and for instances where any change in reading is a gradual one, but for dynamic checking (with the engine running) and the diagnosis of intermittent faults, the oscilloscope is a very powerful workshop tool. Unlike older analogue oscilloscopes dedicated to HT ignition testing, a modern digital oscilloscope has a variable voltage scale, enabling low voltages (typically 0-5 V or 0-12 V) to be displayed and also an adjustable time scale, enabling any wave form to be displayed in the ideal manner. Most oscilloscopes designed for automotive use can be hand-held and are therefore ideal for use in the workshop. They can also be used inside the car, while the vehicle is driven, to capture dynamic data. Usually it is possible to store wave forms and associated data in an internal memory and then print it out or download it onto a PC, enabling the scope patterns to be studied in detail. The oscilloscope display can show the amplitude, frequency, pulse width, shape and pattern of the signal received, by effectively drawing a graph of voltage (vertically) and time (horizontally). It is easy to connect (normally just two leads) and the speed of sampling can be far in excess of even the best of digital multi -meters. This fast response time enables diagnosis of intermittent problems and also enables the effect of disturbing parts of the system to be observed. When necessary, the response time can be slow
10/11/2005
Page 42 of 56
enough to display signals such as the accelerator position (APP)sensor. Once the cause of a problem has been diagnosed and rectified, the repair can be verified by retesting with the oscilloscope. Currently available oscilloscopes are easy to connect and use, enabling a trace to be displayed on the screen without any specialist knowledge or experience. The interpretation of this trace can be greatly assisted by reference to the typical wave forms illustrated in this topic.
Oscilloscope scales
l
l l
To enable testing of the circuit's operating voltage and frequency, each oscilloscope wave form reference in the Pin Data tables has been assigned a voltage and time scale. When testing the circuit, set the oscilloscope to given voltage and time scale. Ensure that the oscilloscope is set to either DC (direct current) or AC (alternating current) as appropriate, and that the trigger level is within the voltage range quoted.
NOTE: Some circuits may require very fine adjustment of the oscilloscope to enable the pattern to be viewed.
l l
Refer to the wave form number For the example:

Typical value 2 V 50 ms per division Fig. 1 - Voltage and time scale
and overlay the voltage and time scale given.
In this example the circuit is operating at approximately 4 volts, switching at approximately 50 ms intervals. Voltage scales used for the patterns in this publication range from 5 mV (mv = millivolt, 1/1000 V) to 20 V per division.
10/11/2005

l
Page 43 of 56
Time scale units used for the patterns in this publication are s = seconds, ms = milliseconds (one thousandth of a second) or s = microsecond (one millionth of a second).
Wave forms
l l
Each oscilloscope wave form has one or more of the following parameters: Amplitude - voltage (V) The signal voltage at a certain moment in time Frequency - cycles per second (Hz) The time between points of the signal Pulse width - duty cycle (%) The period during which the signal is ON - expressed as a percentage (%) of the total Shape - spike, curve, saw -tooth etc. The overall 'picture' of the signal
Fig. 2 - Wave form parameters
Pattern - repeated shapes The pattern of repetition of the overall shape of the signal The oscilloscope will show all these parameters in one display and by comparing the scope traces from the vehicle under test with those illustrated, a judgement can be made about the condition of each circuit and its components. The scope trace for a faulty circuit or component will usually appear very different to that for a satisfactory one, thus simplifying fault identification. The five parameters listed above can be categorised as follows:
Direct current (DC) voltage signals - amplitude only

l
Analogue signal voltages from components such as:

Fig. 3 - Engine coolant temperature (ECT) sensor
10/11/2005
Page 44 of 56
Fig. 4 - Intake air temperature (IAT) sensor
Fig. 5 - Accelerator position (APP)sensor
10/11/2005
Page 45 of 56
Fig. 6 - Mass air flow (MAF) sensor
Alternating current (AC) voltage signals - amplitude, frequency and shape

l
AC voltage signals are generated by components such as:
10/11/2005

Fig. 7 - Injector needle lift sensor
Page 46 of 56
Fig. 8 - Engine speed (RPM) sensor - inductive type
Frequency modulated signals - amplitude, frequency, shape and pulse width
10/11/2005

l
Page 47 of 56
Frequency modulated signals are generated by components such as:

Fig. 9 - Crankshaft position (CKP) sensor - inductive type
Fig. 10 - Camshaft position (CMP) sensor - inductive type
Fig. 11 - Vehicle speed (VSS) sensor - inductive type
10/11/2005
Page 48 of 56
Fig. 12 - Hall-effect speed and position sensors
Pulse width modulated signals - amplitude, frequency, shape, pulse width

l
Pulse width modulated signals from components such as:
10/11/2005

Fig. 13 - Injectors
Page 49 of 56
Fig. 14 - Fuel injection timing solenoid
Fig. 15 - Fuel quantity adjuster
10/11/2005
Page 50 of 56
Fig. 16 - Exhaust gas recirculation (EGR) valves
Interpreting wave forms
10/11/2005

Typical wave forms
l
Page 51 of 56
Oscilloscope wave form patterns can vary greatly and are dependent on many factors. Therefore prior to making a diagnosis or changing components the following points should be considered when the wave form obtained does not appear to be correct when compared with the 'typical' wave form in the pin data table being used.
Voltage
l
Typical wave forms indicate the approximate position of the wave form in relationship to the 'zero grid', but this may vary Fig. 17 [1] , dependent on the system being tested and may be positioned anywhere within the approximate 'zero range' Fig. 17 [2] & Fig. 18 [1] . The amplitude or overall height of the pattern (the voltage) Fig. 17 [3] & Fig. 18 [2] , will depend on the circuit's operating voltage. For direct current (DC) circuits this will depend on the voltage being switched, for example, the fuel injection timing solenoid voltage will be constant and will not vary with engine speed. For alternating current (AC) circuits this will depend on the speed of the signal generator, for example, an inductive crankshaft position (CKP) sensor's output voltage will increase with engine speed. Therefore if the oscilloscope pattern is too high (or the upper part is missing) increase the voltage scale to obtain the view required. If the pattern is too low decrease the voltage scale. Some circuits operating solenoid components, for example the fuel injection timing solenoid, may display voltage spikes Fig. 17 [4] , when the circuit is switched off. This voltage is generated by the component and can normally be ignored. Some circuits that have a square wave type of typical wave form may display the voltage decaying at the end of the switching period Fig. 17 [5] . This is a characteristic of some systems and can normally be ignored, as it does not by itself indicate a fault.
Frequency
l l
The overall width of the pattern (the frequency), will depend on the circuit's operating speed. The typical wave forms illustrated show the wave form viewed with the oscilloscope's time scale set to enable detailed observation. In direct current (DC) circuits the time scale will be dependent on the speed at which the circuit is switched Fig. 17 [6] , for example, the frequency of a fuel quantity adjuster will vary with engine load. In alternating current (AC) circuits the time scale will depend on the speed of the signal generator Fig. 18 [3], for example, an inductive crankshaft position (CKP) sensor's frequency will increase with engine speed. If the oscilloscope pattern is too compressed, decrease the time scale to obtain the view required. If the pattern is too expanded, increase the time scale. If the pattern is reversed Fig. 18 [4] , this indicates that the system being tested has its component connected in the opposite polarity to the typical wave form shown and can normally be ignored as it does not by itself indicate a fault.
Fig. 17 - Digital wave form
10/11/2005
Page 52 of 56
Fig. 18 - Analogue wave form
Component testing
l
Wave forms for a variety of components can be displayed. A few of the more common examples are
10/11/2005
Page 53 of 56
l l l
described below. Most modern oscilloscopes have just two test leads, used with a variety of interchangeable test probes. The red lead is the positive and is normally connected to the ECM pin. The black lead is the negative and is normally connected to a good earth. If the leads are inadvertently connected with the wrong polarity, usually the only consequence is that the wave form will be displayed upside down. All common rail and electronically controlled unit injector systems operate by varying the opening time of the injectors to match the quantity of fuel supplied with the engine operating conditions. The duration of the electrical impulses from the control unit is measured in milliseconds (ms) and typically ranges from 1 to 2 at idle speed. The oscilloscope on most engine testers can be used to display the injector pulse, enabling the duration to be measured. A typical oscilloscope trace is shown in Fig. 19 . Most modern Diesel engines inject fuel in stages called pilot, main and post injection. The first injection (pilot) Fig. 19 [A], occurs as the piston is rising on its compression stroke and is used to pre-condition the combustion chamber. The second injection (main) Fig. 19 [B], occurs at or near top dead centre (TDC) and provides most of the combustion. The third injection (post), used where exhaust emission standards dictate, occurs in the exhaust stroke and is used in conjunction with the exhaust gas recirculation (EGR) system to reduce exhaust emissions. The injectors operate at very high fuel pressures and have to react rapidly necessitating the use of high current solenoids. To reduce the current switched by the ECM, the injector solenoid is rapidly modulated during its open period Fig. 19 [C]. As the injector is energised the voltage at the signal pin falls to, or near zero, and as it is de-energised the returning armature of the solenoid generates a pulse (spike) of high voltage. It is therefore possible to check that the control unit is operating correctly by observing the changes in injector opening times during various engine operating conditions. Injector opening during cranking may be higher than at idle speed, and will increase as the engine load rises.
Fig. 19 - Injectors
10/11/2005

Injector pulse
l
Page 54 of 56
l l l
Using a thin probe, connect the oscilloscope test probe to the ECM injector terminal and the second test probe to earth. Start engine and observe the wave form at idle speed. Depress the accelerator pedal rapidly to increase engine speed to around 3000 rpm. The measured pulse duration should increase during acceleration and then stabilise at a reading equal to or slightly below the idle speed value. Release the accelerator pedal rapidly and the trace should become a straight line with no pulse indicating that injection has been cut-off.
Technical Data Injection Duration Pilot Main 1-2 ms 1-2 ms
Inductive sensors
l l l l l l
The general procedure is as follows: Select sensor pin from pin data list with wave form reference. Connect oscilloscope probe to ECM pin and second probe to earth. Start engine and observe test conditions. Compare scope trace with wave form reference. Raise the engine speed and watch for the voltage (amplitude) display to increase.
Fig. 20 - Inductive sensor wave form
Fuel injection timing solenoid/fuel quantity adjuster
10/11/2005

l
Page 55 of 56
Fuel injection timing solenoids and fuel quantity adjusters come in many different types, each with a different wave form. In each case the duty cycle (or ON time) of the solenoid should increase when additional engine load is applied. If the wave form shows a straight line around the zero mark, or the line is constant at the 5 V or 12 V level, this indicates a fault in the control circuit or ECM signal output.
Fig. 21 - Fuel injection timing solenoid/fuel quantity adjuster wave form
Injector needle lift sensor

l l l
Connect oscilloscope test probes between injector needle lift sensor ECM pin and earth. Compare scope trace with wave form reference Fig. 22 . If the trace shows no wave form but instead is a straight line, this usually indicates a wiring fault or a defective sensor.
NOTE: This sensor only produces a small amount of voltage which may be difficult to detect if the oscilloscope is incorrectly adjusted. Fig. 22 - Injector needle lift sensor wave form
10/11/2005
Page 56 of 56
10/11/2005

Diesel Engine Management

Uploaded by

Copyright:

Available Formats

Diesel Engine Management

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Diesel Engine Management

Uploaded by

Copyright:

Available Formats

Diesel Engine Management Systems Index Diesel Engine Management Systems Index

Diesel Engine management component descriptions

Engine control module (ECM)

file://C:\Documents and Settings\KEN\Local Settings\Temp\~hhDEDF.htm

Diesel Engine Management Systems Index

Outputs from the ECM control some or all of the following:

Fuel supply system

file://C:\Documents and Settings\KEN\Local Settings\Temp\~hhDEDF.htm

Diesel Engine Management Systems Index

Fuel pressure regulator - unit injector

file://C:\Documents and Settings\KEN\Local Settings\Temp\~hhDEDF.htm

Diesel Engine Management Systems Index

Pre-set regulator Circlip 'O' ring 'O' ring Regulator housing

Injectors - mechanical type

file://C:\Documents and Settings\KEN\Local Settings\Temp\~hhDEDF.htm

Diesel Engine Management Systems Index

Injectors - mechanical type, with needle lift sensor

file://C:\Documents and Settings\KEN\Local Settings\Temp\~hhDEDF.htm

Diesel Engine Management Systems Index

Setting pin Sensor winding Pressure pin Electrical connector

Injectors - electrical type

file://C:\Documents and Settings\KEN\Local Settings\Temp\~hhDEDF.htm

Diesel Engine Management Systems Index

file://C:\Documents and Settings\KEN\Local Settings\Temp\~hhDEDF.htm

Diesel Engine Management Systems Index

file://C:\Documents and Settings\KEN\Local Settings\Temp\~hhDEDF.htm

Diesel Engine Management Systems Index

This increase in current is sensed by the ECM.

Protective mesh Resistance wire Intake air Compensating wire

Mass air flow (MAF) sensor - hot-film type

Manifold absolute pressure (MAP) sensor

file://C:\Documents and Settings\KEN\Local Settings\Temp\~hhDEDF.htm

Diesel Engine Management Systems Index

Full load Idling Vacuum connector Piezo-electric crystal Electrical connections

Idle speed control

Idle speed control (ISC) actuator

file://C:\Documents and Settings\KEN\Local Settings\Temp\~hhDEDF.htm

Diesel Engine Management Systems Index

Potentiometer and idle/full load switch Spring Shaft

Engine coolant/intake air temperature sensor

file://C:\Documents and Settings\KEN\Local Settings\Temp\~hhDEDF.htm

Diesel Engine Management Systems Index

Electrical connections Housing NTC resistor

Engine speed and position sensors

file://C:\Documents and Settings\KEN\Local Settings\Temp\~hhDEDF.htm

Diesel Engine Management Systems Index

Sensor Electrical connector

file://C:\Documents and Settings\KEN\Local Settings\Temp\~hhDEDF.htm

Diesel Engine Management Systems Index

Throttle position (TP) sensor

Throttle butterfly shaft Wiper arm Resistance tracks

file://C:\Documents and Settings\KEN\Local Settings\Temp\~hhDEDF.htm

Diesel Engine Management Systems Index

Turbocharger (TC) wastegate regulating valve

file://C:\Documents and Settings\KEN\Local Settings\Temp\~hhDEDF.htm

Diesel Engine Management Systems Index

Cold starting equipment

file://C:\Documents and Settings\KEN\Local Settings\Temp\~hhDEDF.htm

Diesel Engine Management Systems Index

Bosch Common rail