Nitowrap UR512: Two Component Aliphatic Polyurethane Protective Coating

Nitowrap UR512
Two component aliphatic polyurethane protective coating

Uses Nitowrap UR512 provides an easily cleaned chemical and UV resistant protective coating, also suitable for external waterproofing. Advantages Durable : Low maintenance costs Non yellowing : Will not yellow on exposure to UV rays. Chemical resistant : Excellent industrial chemicals resistance to most Sugar (Saturated) Sodium Chloride (Saturated) Methanol Butanol Mineral spirits Xylene Lubrication oil Gasoline : : : : : : : :
constructive solutions
Regular contact Regular contact Occasional contact Occasional contact Regular contact Occasional contact Regular contact Occasional contact
Hygienic : Seamless surface, easily cleaned
Standards compliance Nitowrap UR512 meets the requirements of UL 94 for resistance to spread of flame. Description Nitowrap UR512 is a two component, pigmented, aliphatic polyurethane coating possessing good resistance to long term exposure of UV rays and chemical attack. Technical Support Fosroc offers technical support & service to specifiers and contractors as well as on-site assistance. Properties Pot life at 300C Recoat time at 300C Initial cure at 30 C Final cure at 300C Flash point Chemical resistance Nitowrap UR512 is resistant to chemical attack at ambient temperature, under the following exposure conditions Hydrochloric acid (36%) Nitric acid (15%) Sulphuric acid (10%) Citric acid (10%) Sodium Hydroxide ( 50%) Ammonia (10%) Soln. Bleach concentrate Urea ( Saturated)
Nitowrap UR512
0
At elevated temperatures or where mixtures of chemicals are involved, the effects may be different than the above results. Consult Fosroc for advice. Specification clauses As a protective coating - "Areas as marked on the steel, concrete and/or masonry shall be applied/coated with Nitowrap UR512, a two component aliphatic polyurethane coating to a thickness of 90 - 100 microns d.f.t in two coats of application. When exposed to UV rays for long periods, the cured coated film shall not yellow and chalk. The coated surfaces should retain a semi gloss finish. The potlife of the mixed material shall not be less than one hour at 30 0C. It shall be recoatable in 2 - 4 hours at 300C and shall cure fully in 5 days at 300C. It shall be resistant to spread of flame when tested as per UL94 Standards. It shall develop a minimum bond strength to steel or cementitious substrates of 1.5 N/ mm2 , when tested for Pull Off strength with an Elcometer." As a waterproof coating- "Providing and applying a two part polyurethane based waterproof coating Nitowrap UR512 in 3 coats of application @ 0.1 litre/m2/coat, over rcc slab including sprinkling of clean sand (300 microns - particle size) or, pea gravel and, laying pcc (1:2:4), mixed with integral waterproofing compound, Conplast X421IC, at a dosage of 150ml/50 kg bag of cement, over the fully cured Nitowrap UR512 coating, as per manufacturer's specifications. It shall be an aliphatic, non yellowing, non chalking polyurethane based waterproof coating; with a minimum bond strength of 1.5 N/mm2 to concrete when tested with a Pull Off tester. " The cured film shall be protected with concrete screed / mortar when used on accessible roofs to avoid damage from foot traffic.
: : : : :
Min.1 hour 2 - 4 hours 16 hours 5 days 35 0 C
: : : : : : : :
Occasional contact Occasional contact Regular contact Occasional contact Occasional contact Occasional contact Occasional contact Regular contact
page 1 of 4
Nitowrap UR512
Application instructions
Surface preparation All surfaces must be smooth, sound and free from debris, loose or flaking material and areas of standing water. Surfaces must be free from contamination such as oil, grease, dust, loose particles and organic growth. Concrete surfaces must be fully cured, laitance free and free from any traces of shuttering, release oils and curing compounds. All surfaces should then be grit blasted to remove all foreign matter and open up blow-holes, and provide a suitable key for Nitowrap UR512. All blow holes and imperfections should be filled with Nitomortar FC, epoxy putty. Mixing The individual components should be thoroughly stirred before mixing them together. The components should then be mechanically mixed together for atleast 3 minutes using a slow speed (400 - 500 RPM) drill machine attached with a mixing paddle. Application Apply Nitowrap UR512 with a nylon brush, or a flat pile felt roller, to the prepared substrate at a thickness of 100 microns WFT (45 microns DFT). Allow Nitowrap UR512 first coat to dry for 2-4 hours at 300C and then apply the second coat. When applying Nitowrap UR512 as a topcoat over any of the Nitowrap range of epoxy systems, it must be applied after 6 hours but within 24 hours of applying the epoxy. Note : When applying Nitowrap UR512, if the moisture content in the substrate is more than 3%, blistering of the coating may occur. Curing This coating will become tack free in approximately 2 - 4 hours and be fully cured in 5 days.
Number of coats Two finish coats are recommended unless used as a top coat for freshly applied epoxies. Cleaning Clean tools and equipment immediately after use with Nitoflor Sol. Wash hands and skin with soap, or an industrial hand cleaner. Limitations Minimum ambient surface and material temperature must be between 10 to 400C. For applications outside this range, contact Fosroc for advise. Application of the product should be always on dry substrates.
Storage
Shelf life Nitowrap UR512 has a shelf life of 6 months when stored under normal warehouse conditions in unopened containers. Exposure to moisture greatly reduces the shelf life, particularly that of the hardener.
Estimating
Packaging Nitowrap UR512 Nitoflor Sol Coverage The theoretical coverage is 10 m2 /litre/coat at 45-50 microns DFT (100 microns WFT). However practical coverage may vary depending on the porosity of substrate, application thickness etc. 4 Litres 5 & 20 Litre tins
page 2 of 4
Nitowrap UR512
Precautions
Health & Safety Nitowrap UR512 and Nitoflor Sol should not come in contact with skin or eyes nor should they be swallowed. Avoid inhalation of vapours and ensure adequate ventilation. Some people are sensitive to resins, hardeners and solvents. W ear suitable protective clothing, gloves and eye/face protection. Should accidental skin contact occur, remove immediately with a resin removing cream followed by washing with soap and water - do not use solvent. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. If swallowed seek medical attention immediately - do not induce vomiting. For further information, please consult the Material Safety Datasheet.
Fire Nitowrap UR512 and Nitoflor Sol are flammable. Do not use near a naked flame. Flash Point Nitoflor Sol 33 0C
Additional information Fosroc manufactures a wide range of products specifically designed for the repair and refurbishment of damaged reinforced concrete. This includes repair mortars, fluid micro-concretes, chemical resistant epoxy mortars in addition to comprehensive package of protective coatings. In addition, a wide range of complementary products are available. This includes joint sealants, waterproofing membranes, grouts and anchors and specialised flooring materials. Separate datasheets are available on these products.
page 3 of 4
Nitowrap UR512
Fosroc Chemicals (India) Pvt. Ltd.

Head Office Sapthagiri Palace, No.38, II & III Floor, 12th Cross, CBI Road, Ganganagar North, Bangalore 560 032
Important note : Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard terms and conditions of sale, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that any advice, recommendation specification or information it may give is accurate and correct, it cannot, because it has no direct or continuous control over where or how its products are applied, accept any liability either directly or indirectly arising from the use of its products whether or not in accordance with any advice, specification, recommendation or information given by it.
telephone ++91 80-23551500 fax ++91 80-23551510 e-mail [email protected]
Regional Offices
Bangalore
Sapthagiri Palace, No. 38 II & III Floor, 12th Cross, CBI Road, Ganganagar North, Bangalore 560 032. Ph:080-23551500 Fax : 080-23551510
Mumbai
1401/1402, 14 Floor, A-WingThe Great Eastern Summit Sector-15, CBD, Belapur Navi Mumbai 400 614 Ph: 022 -43406800-04
Noida
D-166 Sector 10 Noida, UP 201 301 Ph:0120-4270620
Kolkata
304, Jodhpur Park Kolkata 700 068 Ph:033-65343188 Fax: 033-2499-0280
www.fosroc.com
page 4 of 4
INDIA/2011/0462/B

Nitowrap UR512: Two Component Aliphatic Polyurethane Protective Coating

Uploaded by

Copyright:

Available Formats

Nitowrap UR512: Two Component Aliphatic Polyurethane Protective Coating

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Nitowrap UR512: Two Component Aliphatic Polyurethane Protective Coating

Uploaded by

Copyright:

Available Formats

Nitowrap UR512

Two component aliphatic polyurethane protective coating

Hygienic : Seamless surface, easily cleaned

Min.1 hour 2 - 4 hours 16 hours 5 days 35 0 C

Fosroc Chemicals (India) Pvt. Ltd.

You might also like