Scribd
Upload
248 views15 pages

Tutorial On Screw Jack: Hareesha N G Dept of Aeronautical Engg Dayananda Sagar College of Engg Bangalore-78

The document provides a tutorial on how to create the different parts of a screw jack using CAD software. It describes the steps to model the body, nut, screw spindle, cup, special washer, and tommy bar of the screw jack. For each part, it lists the planes and sketches to use and the revolved protrusion, cut, hole, thread, and pattern features needed to construct the 3D models. The tutorial aims to guide readers through the entire process of assembling a screw jack digitally piece by piece.

Uploaded by

Hareesha N G
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPS, PDF, TXT or read online on Scribd
248 views15 pages

Tutorial On Screw Jack: Hareesha N G Dept of Aeronautical Engg Dayananda Sagar College of Engg Bangalore-78

The document provides a tutorial on how to create the different parts of a screw jack using CAD software. It describes the steps to model the body, nut, screw spindle, cup, special washer, and tommy bar of the screw jack. For each part, it lists the planes and sketches to use and the revolved protrusion, cut, hole, thread, and pattern features needed to construct the 3D models. The tutorial aims to guide readers through the entire process of assembling a screw jack digitally piece by piece.

Uploaded by

Hareesha N G
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPS, PDF, TXT or read online on Scribd
You are on page 1/ 15

Tutorial on Screw Jack

Hareesha N G Dept of Aeronautical Engg Dayananda Sagar College of Engg Bangalore-78

11/27/2013

Hareesha N Gowda, DSCE, Blore-78

Assembly Drawings
1. Screw Jack

11/27/2013

Hareesha N Gowda, DSCE, Blore-78

Part-1: Create body of the Screw jack 1. Select XZ Plane 2. Draw the 2D sketch as shown 3. Use revolved protrusion command to create 3D feature, Angle 3600

11/27/2013

Hareesha N Gowda, DSCE, Blore-78

Part-2: Create nut of the screw jack 1. Select XZ Plane 2. Draw the 2D sketch as shown 3. Use revolved protrusion command to create 3D feature, Angle 3600

11/27/2013

Hareesha N Gowda, DSCE, Blore-78

Part-3: Create Screw Spindle of the screw jack (Step-1) 1. Select XZ Plane 2. Draw the 2D sketch as shown 3. Use revolved protrusion command to create 3D feature, Angle 3600

11/27/2013

Hareesha N Gowda, DSCE, Blore-78

Part-3: Create Screw Spindle of the screw jack ( Step-2) 1. Select XZ Plane 2. Draw the 2D sketch as shown 3. Use Cut out command to create Symmetric through hole

11/27/2013

Hareesha N Gowda, DSCE, Blore-78

Part-3: Create Screw Spindle of the screw jack ( Step-3) 1. Select XY Plane 2. Draw the 2D sketch as shown 3. Use Cut out command to create Symmetric through hole

11/27/2013

Hareesha N Gowda, DSCE, Blore-78

Part-3: Create Screw Spindle of the screw jack ( Step-4) 1. Select the Plane as shown 2. Go to hole option, set the parameters as shown in dialogue box

11/27/2013

Hareesha N Gowda, DSCE, Blore-78

Part-4: Create CUP of the screw jack (Step-1) 1. Select XZ Plane 2. Draw the 2D sketch as shown 3. Use revolved protrusion command to create 3D feature, angle 3600

11/27/2013

Hareesha N Gowda, DSCE, Blore-78

Part-4: Create CUP of the screw jack (Step-2) 1. Select XZ Plane 2. Draw the 2D sketch as shown 3. Use Cut out command to create the profile as shown 4. Use Circular pattern to create remaining features as shown

11/27/2013

Hareesha N Gowda, DSCE, Blore-78

10

Part-5: Create Special washer of the screw jack 1. Select XZ Plane 2. Draw the 2D sketch as shown 3. Use revolved protrusion command to create 3D feature, angle 3600

11/27/2013

Hareesha N Gowda, DSCE, Blore-78

11

Part-6: Create Special washer of the screw jack (Step-1) 1. Select XZ Plane 2. Draw the 2D sketch as shown 3. Use revolved protrusion command to create 3D feature, angle 3600

11/27/2013

Hareesha N Gowda, DSCE, Blore-78

12

Part-6: Create Special washer of the screw jack (Step-2) 1. Select top surface as shown 2. Draw the 2D sketch as shown 3. Use cut out command to create 3D feature, depth 3mm

11/27/2013

Hareesha N Gowda, DSCE, Blore-78

13

Part-6: Create Special washer of the screw jack (Step-3) 1. Select cylindrical surface as shown 2. Use thread command to create thread feature with the parameters as shown below

11/27/2013

Hareesha N Gowda, DSCE, Blore-78

14

Part-7: Create Tommy Bar of the screw jack Select XZ Plane Draw the 2D sketch as shown Use revolved protrusion command to create 3D feature, angle 3600

11/27/2013

Hareesha N Gowda, DSCE, Blore-78

15

You might also like