FAG Alignment Tools

Top-Laser: SMARTY2 TRUMMY2 EQUILIGN SHIM

Foreword

Higher cost-effectiveness

Correct alignment can help to achieve higher cost-effectiveness. Even machines with very high performance can sometimes still be incapable of fulfilling expectations, for example if they are not adequately aligned. Even minimal deviations can lead to major damage. With the products presented here, Schaeffler assists in the optimum alignment of belts and precise alignment of coupled and non-coupled machine shafts. Alignment is worth performing and gives savings in resources. Precise alignment ensures lower operating and maintenance costs in the long term. In addition, wear is reduced, the lifetime of machinery is increased and energy costs are cut. Products and service for your success reliable, versatile, competent. Even after the purchase of a product, Schaeffler offers lasting solutions relating to mounting and maintenance. With the aid of the diverse portfolio of products and services, operating life and performance capability of production plant can be increased and overall costs can be reduced. In addition, the presence of Schaeffler engineers worldwide guarantees that you receive competent support directly at your location. The portfolio of products and services encompasses not only mounting, lubrication, condition monitoring and rolling bearing reconditioning but also training. All the products and services presented here have been tested in practical use and are certified in accordance with ISO 9001.

Savings

For your success

Foreword

Important to know

In the interests of rapid assistance, Schaeffler has brought together valuable knowledge relating to the mounting and dismounting of rolling bearings in the Mounting Toolbox. Videos show what must be observed in order to achieve correct lubrication, mounting and alignment. The Virtual Plant makes it possible to watch the work of fitting personnel at close quarters, Figure 1.

http://mounting-toolbox.schaeffler.com

Figure 1 Mounting Toolbox

0001935A

Contents
Page Alignment Product overview.................................................................. 4

Features............................................................................... 5 Belt pulley alignment device FAG Top-Laser SMARTY2....... 5 Belt tension measuring device FAG Top-Laser TRUMMY2... 9 Shaft alignment device FAG Top-Laser EQUILIGN............... 12 Shims FAG Top-Laser SHIM .............................................. 21 Services Product overview.................................................................. 24 Mounting ............................................................................. 25 Lubrication........................................................................... 25 Rolling bearing grease Arcanol ......................................... 26 Condition monitoring ........................................................... 26

Schaeffler Technologies

TPI 182

Product overview

Alignment

Belt pulley alignment device Top-Laser SMARTY2 Belt tension measuring device Top-Laser TRUMMY2

LASER-SMARTY2

LASER-TRUMMY2

Shaft alignment device Top-Laser EQUILIGN Shims Top-Laser SHIM

LASER-EQUILIGN

00019CE3

LASER-SHIM

TPI 182

Schaeffler Technologies

00019D92

00019C84

00019C83

Alignment

Features Belt pulley alignment device FAG Top-Laser SMARTY2

These products assist you in the alignment of shafts and belt pulleys and the checking of belt tension values. The FAG Top-Laser SMARTY2 is a line laser for the alignment of belt pulleys and chain sprockets with a diameter of more than 60 mm. The alignment of belt pulleys and chain sprockets reduces wear and energy losses in tension drives, their bearings and seals. Less heat is generated and the lifetime and reliability of the machines is increased. The features of the line laser are as follows: The parallelism and angular errors of the two pulleys are displayed. Alignment can be carried out on both horizontally and vertically mounted belt pulleys. Alignment is significantly more rapid and more precise than with conventional methods. Alignment can be carried out by one person working alone. The measuring device is attached to the pulleys by magnetism. The target marks are available in an optical and an electronic design, Figure 1. In the case of electronic target marks, the adjustment values are displayed in real time on the digital display. Angular errors are shown in degrees, while the parallelism offset is shown in millimetres. Do not look into the laser beam and do not point the laser beam into the eyes of other people.

Caution

Figure 1 Electronic target mark

Schaeffler Technologies

TPI 182

000192A8

Alignment

All the parts are supplied in a lined case, Figure 2. Scope of delivery 1 emitter 2 optical target marks, attached by magnetism 1 battery 1 lined case LASER-SMARTY2

Ordering designation

Emitter Target mark, optical Battery Lined case

Figure 2 Scope of delivery FAG Top-Laser SMARTY2 Replacement part Ordering designation Accessories Ordering designation 1 optical target mark, attached by magnetism LASER-SMARTY2.TARGET 1 electronic target mark, attached by magnetism 1 case LASER-SMARTY2.TARGET-DIGITAL

TPI 182

Schaeffler Technologies

00019CE5

Application

The FAG Top-Laser SMARTY2 can be mounted in just a few seconds, Figure 3.

Laser Target mark, electronic

Figure 3 Mounting The laser can be clearly seen on the target marks. Once the laser beam is adjusted to coincide with the slots in the target marks, the machine is correctly aligned, Figure 4.

Laser beam Target mark, slot Not parallel Correct alignment

Figure 4 Alignment

Schaeffler Technologies

TPI 182

00019C07

00019BFE

Alignment

Technical data FAG Top-Laser SMARTY2

A summary of the technical data is shown in the table.

Laser emitter Power supply Operating time Operating temperature Laser class Laser beam Angle Wavelength Output power Measurement distance Measurement accuracy1) Housing Dimensions (WHD) Mass Material
1)

Battery, 1LR6 (AA) DC 1,5 V 8h +10 C to +40 C 2 78 635 nm to 670 nm 1 mW 10 m (maximum) Better than 0,5 mm or 0,2 145 mm86 mm30 mm 270 g ABS, Al

General rule for deviation, depending on belt type: less than 0,25 (4,4 mm/m).

TPI 182

Schaeffler Technologies

Belt tension measuring device FAG Top-Laser TRUMMY2

Caution Scope of delivery

The robust, handy FAG Top-Laser TRUMMY2 is an optical-electronic manual measuring instrument for belt tension (strand force). The correct belt tension is an essential prequisite for achieving the maximum life of the belt drive. In addition, this also gives reduced wear of the drive components, lower energy costs and increased cost-efficiency. The FAG Top-Laser TRUMMY2 comprises a measurement probe without cable for direct connection, a measurement probe with cable for difficult to access locations and a manual control device that displays the relevant measurables for belt tension as a frequency in Hz or force in N. All the parts of the belt tension measuring device are supplied packed in a case, Figure 5. The simple and reliable user instructions are given in several languages. Do not look into the laser beam and do not point the laser beam into the eyes of other people. 1 manual control device 1 measurement probe for direct connection 1 measurement probe with cable 1 case LASER-TRUMMY2

Ordering designation

Manual control device Measurement probe for direct connection Measurement probe with cable Case

Figure 5 Scope of delivery FAG Top-Laser TRUMMY2

Schaeffler Technologies

TPI 182

00019C87

Alignment

Calibration

We recommend, in accordance with ISO 9001, that the belt tension measuring device should be checked or calibrated at intervals of no more than 2 years. The belt tension measuring device can be sent to us for calibration. Before sending the device, please contact our Technical Support. Calibration LASER-TRUMMY.CALI-CHECK Before calculating the belt tension, the belt mass and length must be entered. Vibration of the belt is then induced. The device measures the natural frequency by means of clock pulse light and uses this to determine the belt tension, Figure 6. This technique is less prone to disruptive influences in comparison with measurement using sound waves.

Service Ordering designation Application

Belt TRUMMY2, cable less measurement probe

Figure 6 Measurement

10

TPI 182

Schaeffler Technologies

00019BFC

Technical data FAG Top-Laser TRUMMY2

A summary of the technical data is shown in the table.

Laser emitter Power supply Operating time Operating temperature Measurement range Digital sampling error Total error Display Strand length, max. Specific belt mass, max. Housing Dimensions (WHD) Mass Material 80 mm126 mm37 mm 300 g ABS Battery, DC 9 V 8h +10 C to +50 C 10 Hz to 800 Hz 1% 5% LCD, 2 lines, 16 characters per line 9,999 m 9,999 kg/m

Schaeffler Technologies

TPI 182

11

Alignment

Shaft alignment device FAG Top-Laser EQUILIGN

Caution

The FAG Top-Laser EQUILIGN, Figure 7, is an alignment system for coupled and decoupled shafts in motors, pumps, ventilators and gearboxes with rolling bearings. The advantages of the system are as follows: simple mounting error-free handling even by untrained personnel using step-by-step display on the manual control device automatic tolerance checking. A symbol indicates when the shafts are correctly aligned more precise alignment than with conventional methods rapid, simple measurement by means of Active Clock measurement mode robust control device. Watertight and insensitive to contamination in accordance with IP65 user interface in 19 languages easy generation of reports real time display of displacement in all axes. Do not look into the laser beam and do not point the laser beam into the eyes of other people.

Figure 7 Shaft alignment device FAG Top-Laser EQUILIGN

12

TPI 182

Schaeffler Technologies

00019C8B

All the parts of the shaft alignment device are supplied packed in a case, Figure 8. Scope of delivery 1 manual control device 1 emitter/receiver including cable 2 m long 1 reflector 5 batteries 1 Allen key 1 cable for connecting USB memory stick to device 1 cable for connecting device to PC via USB port 2 brackets 2 chains, 300 mm long 4 posts, 115 mm long 1 tape measure 1 case LASER-EQUILIGN
00019C8D

Ordering designation

Manual control device Emitter/receiver Reflector Batteries, LR6 (AA) DC 1,5 V, 5 piece Allen key, 4 mm Cable for USB memory stick Cable for PC Bracket Chain, 300 mm long Post,115 mm long Tape measure Case

Figure 8 Scope of delivery FAG Top-Laser EQUILIGN

Schaeffler Technologies

TPI 182

13

Alignment

Replacement parts

Batteries and Allen keys are standardised and can be obtained from trade outlets. All other parts are available as replacement parts, see table.
Description Scope Designation of delivery Quantity 1 1 1 1 1 2 2 4 1 1 LASER-EQUILIGN-DEVICE LASER-EQUILIGN.TRANS LASER-EQUILIGN.REFLECT LASER-EQUILIGN.USB-CABLE LASER-EQUILIGN.PC-CABLE LASER.BRACKET LASER.CHAIN300-SET LASER.POST115-SET LASER.TAPE LASER-EQUILIGN.CASE

Replacement parts, individual parts

Manual control device Emitter/receiver with cable Reflector Cable for USB memory stick, 0,5 m long PC, 2 m long Bracket Chain, 300 mm long Post, 115 mm long Tape measure, 1 m long Case

Accessories

A comprehensive range of accessories is available in order to expand the possible applications of the base device FAG Top-Laser EQUILIGN, see tables and Figure 9, page 15. The accessories can be ordered as a set in a handy, robust case or as individual parts.
Description Scope Designation of delivery Quantity 2 2 4 4 4 4 1 LASER.CHAIN600-SET LASER.CHAIN1500-SET LASER.POST150-SET LASER.POST200-SET LASER.POST250-SET LASER.POST300-SET LASER.BRACKET-MAGNET

Accessories, individual parts

Chain Post

600 mm long 1500 mm long 150 mm long 200 mm long 250 mm long 300 mm long

Magnetic holder including 2 posts, 150 mm long

14

TPI 182

Schaeffler Technologies

Accessories, set

Description

Scope of delivery Quantity 2 2 4 4 4 4 2 1

Designation

Chain Post

600 mm long 1500 mm long 150 mm long 200 mm long 250 mm long 300 mm long

LASER.ACCESS-SET

Magnetic holder including 2 posts, 150 mm long Case

Chains, 600 mm Chains, 1500 mm Posts, 150 mm Posts, 200 mm Posts, 250 mm Posts, 300 mm Magnetic holder Case

Figure 9 Accessories, set

Schaeffler Technologies

TPI 182

15

00019C90

Alignment

Handling and use

The emitter/receiver is mounted on the shaft of the non-movable side of the subassembly by means of a clamping device. The reflector is then mounted on the shaft of the movable opposing side, Figure 10. The emitter/receiver and manual control device are then connected to each other by means of a cable. The manual control device is switched on and the dimensions of the machine are inputted. A soft foot is defined as a machine foot that lifts off the floor when the foot screw connection is slackened. If a soft foot is present, this must be removed before alignment is carried out. Each individual foot screw connection is loosened and the device is monitored to see if it displays any changes between the foot screwed firmly into place and the loosened foot. The soft foot can then be eliminated using shims, page 21.

Actions to be taken before alignment

Emitter/receiver Reflector Soft foot, display Soft foot, foot screw connection

Figure 10 Finding the soft foot

16

TPI 182

Schaeffler Technologies

00019DB8

Alignment

Once the soft foot has been eliminated, the alignment process can be started. During measurement, at least three positions are approached at different angles. These must be measured at an angle of at least 90. The intelligent control system prevents incorrect usage here. The actual condition of the subassembly is then displayed, Figure 11. Once the foot screw connections have been loosened, the vertical misalignment is first eliminated by means of shims. FAG Top-Laser EQUILIGN shows the displacement in real time. This means that the user can monitor on the display how the measurement results change as soon as the subassembly is moved. Horizontal adjustment is then carried out until the symbol with the thumb pointing upwards is displayed. Once the foot screw connections are tightened, the shafts are aligned.

Display of actual condition Foot screw connection Direction of vertical displacement Direction of horizontal displacement

Figure 11 Alignment

Schaeffler Technologies

TPI 182

17

00019DB8

Alignment

Compilation of results

After just five operating steps, the subassembly is aligned, Figure 12.

Input of dimensions Identification of soft foot Measurement Display of actual condition Display of displacement Symbol thumbs up = everything is OK

Figure 12 Compilation of results Control measurement

Finally, a control measurement is carried out and the measurement result is recorded with the aid of the report generator function integrated in the device.

18

TPI 182

Schaeffler Technologies

0001A4DC

Technical data FAG Top-Laser EQUILIGN

A summary of the technical data is shown in the tables.

Manual control device Power supply Operating time1) Operating temperature Hardware Processor Memory Connectors Data transfer LCD display Type Display Size Resolution Illumination TFT, transmissive 65 535 greyscales 8,9 cm (3,5 inch) 320240 pixels LED background illumination Integrated photometer for automatic adjustment of display brightness to environment LED, multi-colour LED, multi-colour USB 2.0, Host & Slave RS 232 Intel XScale PXA270 312 MHz 64 MB RAM 32 MB Flash Batteries, 5 LR6 (AA) DC 1,5 V 9h 0 C to +50 C

Status displays Battery display Laser alignment, alignment status Keyboard Key elements Navigation keys: up, down, left, right Enter key Back key Delete key Menu key Alphanumeric keyboard Additional keys for functions: Dimensions, Measurement, Results, Soft foot, LiveMove 220 mm165 mm45 mm 742 g IP65

Housing Dimensions (WHD) Mass Protection type

1)

In operating cycle: 33% measurement, 33% data processing, 33% standby.

Schaeffler Technologies

TPI 182

19

Alignment

FAG Top-Laser EQUILIGN (continued)

Emitter/receiver Measurement distance Dimensions (WHD) Mass Protection type Laser Principle Type Class Laser beam, wavelength Output power Detector Measurement range Resolution Accuracy Inclinometer Measurement range Resolution Reflector Design Accuracy Dimensions (WHD) Mass Protection type Case Dimensions (WHD) Mass Material User interface Language versions German, English, US English, Chinese (traditional), Chinese (simplified), Finnish, French, Indonesian, Italian, Japanese, Korean, Dutch, Polish, Portuguese, Russian, Swedish, Spanish, Thai, Czech 500 mm410 mm140 mm 4,1 kg ABS 90 mm roof prism 1% 100 mm41 mm35 mm 65 g IP67 0 to 360 1 Any, dynamically expandable 1 m 98% Coaxial, reflected laser beam Ga-Al-As semiconductor laser 2, FDA 21 CFR 1000 & 1040 675 nm, red, visible 1 mW 5 m (maximum) 107 mm70 mm49 mm 177 g IP67

20

TPI 182

Schaeffler Technologies

Shims FAG Top-Laser SHIM

Shims FAG Top-Laser SHIM are used to eliminate vertical misalignment or soft feet. These shims are made from corrosion-resistant alloy steel and are available in seven thicknesses (0,05 mm, 0,1 mm, 0,2 mm, 0,5 mm, 0,7 mm, 1 mm 2 mm) and in four sizes (dimension c = 15 mm, 23 mm, 32 mm, 44 mm), Figure 13 and table, page 22.

Figure 13 Shim, dimensions Scope of delivery Basic set

Ordering designation Replacement parts

1 case 360 shims: 20 shims each in three sizes (dimension c = 15 mm, 23 mm, 32 mm) and six thicknesses (0,05 mm to 1 mm) 1 extraction hook LASER.SHIM-SET As replacement parts, we supply 10 shims each in one of the 4 sizes and one of the 7 thicknesses. Ordering example 1: 10 shims with dimension c = 15 mm and 0,2 mm thickness LASER.SHIM15X0,20 Ordering example 2: 10 shims with dimension c = 44 mm and 0,1 mm thickness LASER.SHIM44X0,10

Ordering designation

Ordering designation

Schaeffler Technologies

TPI 182

21

00017A47

Alignment

Available shims

Designation

Mass m g/10 piece

Dimensions a mm 55 55 55 55 55 55 55 75 75 75 75 75 75 75 90 90 90 90 90 90 90 125 125 125 125 125 125 125 b mm 50 50 50 50 50 50 50 70 70 70 70 70 70 70 80 80 80 80 80 80 80 105 105 105 105 105 105 105 c mm 15 15 15 15 15 15 15 23 23 23 23 23 23 23 32 32 32 32 32 32 32 44 44 44 44 44 44 44 Thickness mm 0,05 0,1 0,2 0,5 0,7 1 2 0,05 0,1 0,2 0,5 0,7 1 2 0,05 0,1 0,2 0,5 0,7 1 2 0,05 0,1 0,2 0,5 0,7 1 2

LASER.SHIM15X0,05 LASER.SHIM15X0,10 LASER.SHIM15X0,20 LASER.SHIM15X0,50 LASER.SHIM15X0,70 LASER.SHIM15X1,00 LASER.SHIM15X2,00 LASER.SHIM23X0,05 LASER.SHIM23X0,10 LASER.SHIM23X0,20 LASER.SHIM23X0,50 LASER.SHIM23X0,70 LASER.SHIM23X1,00 LASER.SHIM23X2,00 LASER.SHIM32X0,05 LASER.SHIM32X0,10 LASER.SHIM32X0,20 LASER.SHIM32X0,50 LASER.SHIM32X0,70 LASER.SHIM32X1,00 LASER.SHIM32X2,00 LASER.SHIM44X0,05 LASER.SHIM44X0,10 LASER.SHIM44X0,20 LASER.SHIM44X0,50 LASER.SHIM44X0,70 LASER.SHIM44X1,00 LASER.SHIM44X2,00

8 17 40 80 120 170 334 16 31 60 150 220 320 630 16 38 80 190 270 390 774 50 90 140 363 505 694 1362

22

TPI 182

Schaeffler Technologies

Schaeffler Technologies

TPI 182

23

Product overview

Services

Mounting

MOUNT-HOUR

Lubrication

ARCA-PUMP

Condition monitoring

CM-HOUR-ENGINEER

24

TPI 182

Schaeffler Technologies

0001A366

0001A364

0001A362

Services

In addition to alignment as a service, Schaeffler can provide numerous solutions for your specific requirements. Here are some examples from the product portfolio of Schaeffler Industrial Aftermarket.

Mounting

Our experienced fitters can support you in the mounting and dismounting of rolling bearings and advise you on the selection of suitable mounting tools. Correct mounting is an essential precondition for achieving the maximum operating life of bearings. In the case of the London Eye, Schaeffler supplied the rolling bearings and carried out the mounting operations, Figure 1.

Figure 1 Double row FAG spherical roller bearing in the London Eye

Lubrication

Unsuitable lubrication can impair the operating life of rolling bearings and cause damage. In order to achieve the most suitable lubrication, Schaeffler can provide specifically designed and tested greases, Figure 2.

Figure 2 Rolling bearing grease for every bearing arrangement

Schaeffler Technologies

TPI 182

25

000192B4

00017E25

Services

Rolling bearing grease Arcanol

The 17 different greases cover almost all applications. They are developed by experienced application engineers and are produced by the best manufacturers in the market. Different greases are used depending on the particular application. At high operating temperatures, the thermally stable special grease Arcanol TEMP120 is used. Rolling bearing greases under the name Arcanol are subject to 100% quality inspection. The inspection methods at Schaeffler are among the most demanding in the market. As a result, rolling bearing greases Arcanol fulfil the highest quality requirements. The malfunction-free and optimised operation of complex machinery and plant can only be achieved by means of condition-based maintenance. In many cases, Schaeffler uses vibration diagnosis. For example, FAG SmartCheck is an innovative measuring system for real time monitoring with a patented diagnosis technology. Due to the low purchase costs, it can be used economically even on smaller subassemblies. The compact measuring device can be installed quickly, is easy to use and contributes through its trendsetting characteristics to process optimisation and the reduction of life cycle costs. In this way, you receive the best information on the condition of your machinery, Figure 3.

Condition monitoring

Pump FAG SmartCheck

Figure 3 FAG SmartCheck, application example

26

TPI 182

Schaeffler Technologies

0001A1D2

Notes

Schaeffler Technologies

TPI 182

27

Notes

28

TPI 182

Schaeffler Technologies

Schaeffler Technologies

TPI 182

29

Notes

30

TPI 182

Schaeffler Technologies

Schaeffler Technologies

TPI 182

31

Notes

32

TPI 182

Schaeffler Technologies

Further information
Industrial Aftermarket Products and services for your success www.schaeffler.com/services

Schaeffler Mounting Toolbox Virtual Plant: About the Mounting Service http://mounting-toolbox.schaeffler.com

MATNR 035582600-0000 / TPI 182 / 02 / GB-D / 2013072 / Printed in Germany by wnsch

Schaeffler Technologies AG & Co. KG Postfach 1260 97419 Schweinfurt Germany Georg-Schfer-Strae 30 97421 Schweinfurt Germany Phone Fax E-mail +49 2407 9149-66 +49 2407 9149-59 [email protected]

Every care has been taken to ensure the correctness of the information contained in this publication but no liability can be accepted for any errors or omissions. We reserve the right to make technical changes. Schaeffler Technologies AG & Co. KG Issued: 2013, July This publication or parts thereof may not be reproduced without our permission. TPI 182 GB-D

Internet www.schaeffler.com/services