0% found this document useful (0 votes)
172 views20 pages

tm043ndh02 F v2.0 PDF

This document provides specifications for the TM043NDH02 LCD module from Shanghai Tianma Micro-Electronics. It includes details on the module's general specifications, electrical characteristics, interface timing, environmental testing, mechanical drawings, and precautions for use. The module has a 4.3-inch active area with 480 x 272 RGB pixel resolution and is driven by a TFT LCD panel and LED backlight. Timing parameters and electrical limits are provided for driving the panel and backlight.

Uploaded by

mayito12093120
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
172 views20 pages

tm043ndh02 F v2.0 PDF

This document provides specifications for the TM043NDH02 LCD module from Shanghai Tianma Micro-Electronics. It includes details on the module's general specifications, electrical characteristics, interface timing, environmental testing, mechanical drawings, and precautions for use. The module has a 4.3-inch active area with 480 x 272 RGB pixel resolution and is driven by a TFT LCD panel and LED backlight. Timing parameters and electrical limits are provided for driving the panel and backlight.

Uploaded by

mayito12093120
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 20

SHANGHAI TIANMA MICRO-ELECTRONICS

TM043NDH02 V2.0

Coversheet

MODEL NO. : ISSUED DATE: VERSION :

TM043NDH02 2010-10-08 Ver 2.0

Preliminary Specification Final Product Specification

Customer : Approved by Notes

SHANGHAI TIANMA Confirmed : Prepared by

Checked by

Approved by

This technical specification is subjected to change without notice

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation, and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation.
Page 1 of 20

SHANGHAI TIANMA MICRO-ELECTRONICS

TM043NDH02 V2.0

Table of Contents
Coversheet........................................................................................................................................ 1 Record of Revision............................................................................................................................ 3 1. General Specifications ............................................................................................................... 4 2. Input/Output Terminals ............................................................................................................... 5 3 Absolute Maximum Ratings ....................................................................................................... 6 4 Electrical Characteristics............................................................................................................ 6 4.1 Driving TFT LCD Panel........................................................................................................ 6 4.2 Driving Backlight .................................................................................................................. 7 4.3 Block Diagram ..................................................................................................................... 7 5. Interface timing ............................................................................................................................. 8 5.1 Input Setup Timing Setting................................................................................................... 8 5.2 Data Input Format.............................................................................................................. 10 5.3 Power ON/OFF Sequence................................................................................................. 13 6. Optical Characteristics ............................................................................................................. 14 7. Environmental / Reliability Test ................................................................................................ 17 8. Mechanical Drawing................................................................................................................. 18 9. Packing Drawing ...................................................................................................................... 19 10. Precaution for Use of LCD Modules......................................................................................... 20

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation, and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation.
Page 2 of 20

SHANGHAI TIANMA MICRO-ELECTRONICS

TM043NDH02 V2.0 Editor Haitao Chen Haitao Chen Xing Nie

Record of Revision
Rev 1.0 1.1 2.0 Issued Date 2010-07-13 2010-08-02 Description Preliminary release.
Clock for input data latched change at falling edgerising edge

2010-10-08 Final Product Specification Release

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation, and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation.
Page 3 of 20

SHANGHAI TIANMA MICRO-ELECTRONICS

TM043NDH02 V2.0 Spec 4.3 inch 480(RGB) x 272 RGB 24 bits 16.7M a-Si 0.198x0.198 R.G.B. Vertical Stripe TM with Normally White Anti-Glare(3H) 6 oclock 12 oclock 105.50x67.20x2.90 95.04x53.86 Without TSP 44.065 10 LEDs

1. General Specifications
Feature Size Resolution Interface Color Depth Technology Type Pixel Pitch (mm) Display Spec. Pixel Configuration Display Mode Surface Treatment(Up Polarizer) Viewing Direction Gray Scale Inversion Direction LCM (W x H x D) (mm) Active Area(mm) Mechanical Characteristics With /Without TSP Weight (g) LED Numbers

Note 1: Viewing direction for best image quality is different from TFT definition, there is a 180 degree shift. Note 2: Requirements on Environmental Protection: Q/S0002 Note 3: LCM weight tolerance: 5%

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation, and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation.
Page 4 of 20

SHANGHAI TIANMA MICRO-ELECTRONICS

TM043NDH02 V2.0 Remark

2. Input/Output Terminals
Back light cathode Back light anode Ground Power supply Data input Data input Data input Data input Data input Data input Data input Data input Data input Data input Data input Data input Data input Data input Data input Data input Data input Data input Data input Data input Data input Data input Data input Data input Ground Clock for input data. Data latched at rising edge of this 30 DCLK I signal. Standby mode. 31 DISP I DISP =1: Normally operation. DISP =0: Standby mode. Horizontal sync input with negative polarity. If unused, 32 HSYNC I please pull high level. Vertical sync input with negative polarity. If unused, 33 VSYNC I please pull high level. 34 DE I Data input enable. If unused, please pull low level. 35 NC -No connection 36 GND P Ground. 37 X_R -No connection 38 Y_B -No connection 39 X_L -No connection 40 Y_T -No connection NoteI--InputO--OutputP--Power/Ground
Table 2.1 Input Terminal Pin Assignment

No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29

Symbol VLEDVLED+ GND VDD R0 R1 R2 R3 R4 R5 R6 R7 G0 G1 G2 G3 G4 G5 G6 G7 B0 B1 B2 B3 B4 B5 B6 B7 GND

I/O P P P P I I I I I I I I I I I I I I I I I I I I I I I I P

Description

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation, and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation.
Page 5 of 20

SHANGHAI TIANMA MICRO-ELECTRONICS

TM043NDH02 V2.0

3 Absolute Maximum Ratings


3.1 Driving TFT LCD Panel
Item Supply Voltage Back Light Forward Current Operating Temperature Storage Temperature Symbol VDD ILED TOPR TSTG -20 -30 Min -0.3 Max 4.0 25 70 80 Unit V mA For each LED GND=0V,Ta=25 Remark

Note1: The parameter is for driver IC (gate driver, source driver) only. Note2: Signals include R0~R5, G0~G5, B0~B5, DCLK, DISP, HSYNC, VSYNC, DE
Table 3.1 absolute maximum rating

4 Electrical Characteristics
4.1 Driving TFT LCD Panel
Item Supply Voltage Input Signal Voltage Output Signal Voltage Low Level High Level Low Level High Level Symbol VDD VIL VIH VOL VOH Black Mode (60Hz) Standby Mode Min 3.0 0 0.7xVDD -0.8xVDD Typ 3.3 ----74.0 50 Max 3.6 0.3xVDD VDD 0.2xVDD VDD Unit V V V V V mW uW Note1 GND=0V, Ta=25 Remark R0~R5, G0~G5, B0~B5, DCLK, DISP, HSYNC, VSYNC, DE

(Panel+LSI) Power Consumption

Note1: To test the current dissipation, use all Black Pattern.


Table 4.1 LCD module electrical characteristics

4.2 Driving Backlight


Item Channel Forward Voltage Backlight Power Consumption Life Time Symbol Ichannel VBL WBL -Min ---10,000 Typ 20.0 3.2 640 (20,000) Max 25.0 ---Unit mA V mW Hrs Note 3 Remark Note 1

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation, and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation.
Page 6 of 20

SHANGHAI TIANMA MICRO-ELECTRONICS

TM043NDH02 V2.0

Note 1: IF is defined for one channel LED. There are total two LED channels in back light unit Note 2: Optical performance should be evaluated at Ta=25 only. Note 3: If LED is driven by high current, high ambient temperature & humidity condition. The life time of LED will be reduced.Operating life means brightness goes down to 50% initial brightness. Typical operating life time is estimated data.
Table 4.2 LED backlight characteristics

Figure 4.2 LED connection of backlight

4.3 Block Diagram

LCD Panel VCOM & TCON

R[7:0] G[7:0] B[7:0] Source + Gate Driver

Data bus

4.3 inch 480(RGB)*272

VSYNCHSYNC DEDCLKDISP

Control signal input FPC

Grayscale Manipulation Voltage

DC/DC

VDD,GND Power

VLED+VLEDBLU BLU

Figure 4.3 LCD Module Diagram

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation, and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation.
Page 7 of 20

SHANGHAI TIANMA MICRO-ELECTRONICS

TM043NDH02 V2.0

5. Interface timing
5.1 Input Setup Timing Setting
5.1.1 Input Setup Timing Parameter Setting
VDD=3.3V Ta=25 Normal Write Mode

Parameter Symbol Min Typ Max DCLK Cycle Time Tpw 66.7 DCLK Pulse High Width Tpwh 26.7 DCLK Pulse Low Width Tpwl 26.7 DE Setup Time Tdes 10 DE Hold Time Tdeh 10 HSYNC Setup Time Ths 10 HSYNC Hold Time Thh 10 VSYNC Setup Time Tvhs 10 VSYNC Hold Time Tvhh 10 Data Setup Time Tds 10 Data Hold Time Tdh 10 DISP Setup Time Tdiss 10 DISP Hold Time Tdish 10 Note 1tr=tf=2ns.tr, tf is defined 10% to 90% of signal amplitude. Note 2For parallel interface, maximum clock frequency is 15MHz.

Unit ns ns ns ns ns ns ns ns ns ns ns us ms

Remark

Table 5.1 Input Setup Timing Parameters Requirement

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation, and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation.
Page 8 of 20

SHANGHAI TIANMA MICRO-ELECTRONICS 5.1.2 Input Setup Timing Diagram

TM043NDH02 V2.0

VSYNC

0.7*VDDIO

tdiss

tdish
0.7*VDDIO

DISP

0.7*VDDIO

VSYNC
0.3*VDDIO 0.3*VDDIO

tvhs

tvhh
0.7*VDDIO

HSYNC

0.7*VDDIO

DCLK

HSYNC
0.3*VDDIO

ths

thh

0.3*VDDIO

DCLK

0.3*VDDIO

0.7*VDDIO

tPW

DCLK

tPWh

tPWl
0.7*VDDIO 0.7*VDDIO

R[7:0] G[7:0] B[7:0]

tds invalid

tdf
0.7*VDDIO 0.3*VDDIO

invalid

tdes

tdeh
0.7*VDDIO

DE

0.7*VDDIO

Figure 5.1.2 Input Setup Timing Diagram

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation, and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation.
Page 9 of 20

SHANGHAI TIANMA MICRO-ELECTRONICS

TM043NDH02 V2.0

5.2 Data Input Format


5.2.1 Data Input Timing Parameter Setting Parameter DCLK frequency HSYNC frequency VSYNC frequency Horizontal cycle Horizontal display period Horizontal pulse width Horizontal back porch Horizontal front porch Vertical cycle Vertical display period Vertical pulse width Vertical back porch Vertical front porch Symbol fclk 1/th 1/tv th thd thp thb thf tv tvd tvp tvb tvf Min ---525 2 2 2 285 1 1 1 Typ 9 17.14 59.94 525 480 41 2 2 286 272 10 2 2 Max 15 --605 41 41 82 399 11 11 227 Unit MHZ KHz Hz DCLK DCLK DCLK DCLK DCLK HSYNC HSYNC HSYNC HSYNC HSYNC Remark

Note 1Unit: CLK=1/ fCLK , H= th, Note 2It is necessary to keep tvp+tvb=12 and thp+thb= 43 in sync mode. DE mode is unnecessary to keep it. Table 5.2.2 Data Input Timing Parameters Requirement

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation, and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation.
Page 10 of 20

SHANGHAI TIANMA MICRO-ELECTRONICS

TM043NDH02 V2.0

5.2.2 Data Input Timing Diagram


5.2.2.1 Data Input Timing Diagram under SYNC Mode

Figure 5.2.1 Data Input Timing Diagram Under SYNC Mode(DE=L)

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation, and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation.
Page 11 of 20

SHANGHAI TIANMA MICRO-ELECTRONICS 5.2.2.2 Data Input Timing Diagram under DE Mode

TM043NDH02 V2.0

Figure 5.2.2 Data Input Timing Diagram Under DE Mode(VSYNC/HSYNC=H)

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation, and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation.
Page 12 of 20

SHANGHAI TIANMA MICRO-ELECTRONICS

TM043NDH02 V2.0

5.3 Power ON/OFF Sequence


5.3.1 Power ON Sequence

Figure 5.3.1 Power on sequence

5.3.2 Power OFF Sequence

Figure 5.3.2 Power off sequence

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation, and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation.
Page 13 of 20

SHANGHAI TIANMA MICRO-ELECTRONICS

TM043NDH02 V2.0 Typ 70 50 70 70 500 20 0.315 0.335 0.581 0.345 0.348 0.581 0.153 0.095 80 Max -----30 0.365 0.385 0.631 0.395 0.395 0.631 0.203 0.145 ---Unit Remark

6. Optical Characteristics
Item View Angles Contrast Ratio Response Time White Red Chromaticity Green Blue Uniformity Symbol Condition T B CR10 L R CR =0 TON TOFF x y x y x y x y U 25 Min 60 40 60 60 400 -0.265 0.285 0.531 0.295 0.298 0.531 0.103 0.045 75

Degree Note 2 Note1 Note3 ms Note1 Note4

Backlight is on

Note5 Note1

Note1 Note6

NTSC -50 Luminance L 250 300 Test Conditions: 1. IF= 20mA(one channel),the ambient temperature is 25. 2. The test systems refer to Note 1 and Note 2.

% Note 5 2 cd/m Note1 Note7

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation, and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation.
Page 14 of 20

SHANGHAI TIANMA MICRO-ELECTRONICS TM043NDH02 V2.0 Note 1: Definition of optical measurement system. The optical characteristics should be measured in dark room. After 5 Minutes operation, the optical properties are measured at the center point of the LCD screen. All input terminals LCD panel must be ground when measuring the center area of the panel.
Photo detector Field

Item Contrast Ratio


500mm LCD Panel

Photo detector

Field

TFT-LCD Module

Luminance Chromaticity Lum Uniformity Response Time

SR-3A

BM-7A

The center of the screen


Note 2: Definition of viewing angle range and measurement system. viewing angle is measured at the center point of the LCD by CONOSCOPE(ergo-80)

Note 3: Definition of contrast ratio

White state : The state is that the LCD should drive by Vwhite. Black state: The state is that the LCD should drive by Vblack. Vwhite: To be determined Vblack: To be determined. Note 4: Definition of Response time The response time is defined as the LCD optical switching time interval between White state and Black state. Rise time (TON) is the time between photo detector output intensity changed from 90% to 10%. And fall time (TOFF) is the time between photo detector output intensity changed from 10% to 90%.

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation, and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation.
Page 15 of 20

SHANGHAI TIANMA MICRO-ELECTRONICS

TM043NDH02 V2.0

Note 5: Definition of color chromaticity (CIE1931) Color coordinates measured at center point of LCD. Note 6: Definition of Luminance Uniformity Active area is divided into 9 measuring areas (Refer Fig. 2). Every measuring point is placed at the center of each measuring area. Luminance Uniformity (U) = Lmin/ Lmax L-------Active area length W----- Active area width

Lmax: The measured Maximum luminance of all measurement position. Lmin: The measured Minimum luminance of all measurement position. Note 7: Definition of Luminance: Measure the luminance of white state at center point.

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation, and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation.
Page 16 of 20

SHANGHAI TIANMA MICRO-ELECTRONICS

TM043NDH02 V2.0 Remarks Note1 IEC60068-2-1,GB2423.2 IEC60068-2-1 GB2423.1 IEC60068-2-1 GB2423.2 IEC60068-2-1 GB2423.1 Note2 IEC60068-2-78 GB/T2423.3 Start with cold temperature, End with high temperature, IEC60068-2-14,GB2423.22 IEC61000-4-2 GB/T17626.2

7. Environmental / Reliability Test


No 1 2 3 4 5 6 Test Item High Temperature Operation Low Temperature Operation High Temperature Storage Low Temperature Storage Storage at High Temperature and Humidity Thermal Shock (non-operation) Condition Ts = +70, 240 hours Ta = -20, 240 hours Ta = +80, 240 hours Ta = -30, 240 hours Ta = +60, 90% RH max,240hours -20 30 min~+80 30 min, Change time:5min, 100 Cycle

C=150pF,R=330,5point/panel Air:8Kv,5times; Contact:4Kv,5times 7 ESD (Environment:15~35, 30%~60%.86Kpa~106Kpa) Frequency range:10~55Hz Stroke:1.5mm 8 Vibration Test Sweep:10Hz~55Hz~10Hz 2 hours for each direction of X.Y.Z. (6 hours for total) Half Sine Wave Mechanical Shock 9 60G 6ms, X,Y,Z (Non Op) 3times for each direction Height:60cm, 10 Package Drop Test 1corner,3edges,6surfaces Random Vibration: 0.015G*G/Hz for 5-200Hz, Package Vibration 11 -6dB/Octave from 200-500Hz Test 2 hours for each direction of X,Y,Z (6 hours for total) Note1: Ts is the temperature of panels surface. Note2: Ta is the ambient temperature of samples.

IEC60068-2-6 GB/T2423.10 IEC60068-2-27 GB/T2423.5 IEC60068-2-32 GB/T2423.8 IEC60068-2-34 GB/T2423.11

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation, and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation.
Page 17 of 20

SHANGHAI TIANMA MICRO-ELECTRONICS

TM043NDH02 V2.0

8. Mechanical Drawing
DD LEDLED+

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation, and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation.
Page 18 of 20

SHANGHAI TIANMA MICRO-ELECTRONICS

TM043NDH02 V2.0

9.
No 1 2 3. 4 5 6 7 8

Packing Drawing
Item LCM module Partition_1 Anti-Static Bag Dust-Proof Bag Partition_2 Corrugated Bar Carton Total weight Model(Material) TM043NDH02 Corrugated Paper PE PE Corrugated Paper Corrugated Paper Corrugated Paper Dimensions (mm) 105.5x67.2x2.9 513x333x106 175.8x125x0.05 700x530 505x332x4.00 513x117x3 530x350x250 TBD Kg Unit Weigt (Kg) 0.044 0.7 0.0007 0.0600 0.09 0.04 1.1000 Quantity 112 2 112 1 3 8 1 Anti-static Remark

9.1 Packaging Material

Note: Packaging Specification and Quantity Module quantity in a carton28pcs(per row)x2(per column)x2= 112pcs

9.2 Packing Instruaction

2 0120 1

20 1201

2 0120 1

20 1201

2 0120 1

20 1201

2 0120 1

20 1201

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation, and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation.
Page 19 of 20

SHANGHAI TIANMA MICRO-ELECTRONICS

TM043NDH02 V2.0

10. Precautions for Use of LCD Modules


10.1 Handling Precautions 10.1.1 The display panel is made of glass. Do not subject it to a mechanical shock by dropping it from a high place, etc. 10.1.2 If the display panel is damaged and the liquid crystal substance inside it leaks out, be sure not to get any in your mouth, if the substance comes into contact with your skin or clothes, promptly wash it off using soap and water. 10.1.3 Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary. 10.1.4 The polarizer covering the display surface of the LCD module is soft and easily scratched. Handle this polarizer carefully. 10.1.5 If the display surface is contaMinated, breathe on the surface and gently wipe it with a soft dry cloth. If still not completely clear, moisten cloth with one of the following solvents: Isopropyl alcohol Ethyl alcohol Solvents other than those mentioned above may damage the polarizer. Especially, do not use the following: Water Ketone Aromatic solvents 10.1.6 Do not attempt to disassemble the LCD Module. 10.1.7 If the logic circuit power is off, do not apply the input signals. 10.1.8 To prevent destruction of the elements by static electricity, be careful to maintain an optimum work environment. 10.1.8.1 Be sure to ground the body when handling the LCD Modules. 10.1.8.2 Tools required for assembly, such as soldering irons, must be properly ground. 10.1.8.3 To reduce the amount of static electricity generated, do not conduct assembly and other work under dry conditions. 10.1.8.4 The LCD Module is coated with a film to protect the display surface. Be care when peeling off this protective film since static electricity may be generated. 10.2 Storage precautions 10.2.1 When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps. 10.2.2 The LCD modules should be stored under the storage temperature range. If the LCD modules will be stored for a long time, the recommend condition is: Temperature : 0 40 Relatively humidity: 80% 10.2.3 The LCD modules should be stored in the room without acid, alkali and harmful gas. 10.3 Transportation Precautions 10.3.1 The LCD modules should be no falling and violent shocking during transportation, and also should avoid excessive press, water, damp and sunshine.

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation, and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation.
Page 20 of 20

You might also like