Department of Civil and Environmental Engineering CVNG 1001: Mechanics of Fluids

INTRODUCTION Hydrodynamic Machines A hydromachine is a device used either for extracting energy from a fluid or to add energy to a fluid. There are many types of hydromachines and Figure 1 below illustrates some common types.
Hydrodynamic Machines Machines where energy is added to the fluid, i.e. work is done on the fluid Machines where energy is extracted from the fluid, i.e. work is done by the fluid

Rotodynamic Machines

Positive Displacement Machines

Rotodynamic Machines

Positive Displacement Machines

Pumps, Fans, Compressors

Pumps, Compressors

Turbines

Motors

Cased

Uncased

Reciprocating

Rotary

Impulse

Reaction

Piston Vane

Axial Flow
flow is perpendicular to the plane of impeller rotation or along its axis of rotation

Propellers

Swash Plate

Screw

Mixed Flow Radial Flow (Centrifugal Pumps)

flow is in the plane of impeller rotaion or perpendicular to the axis of its rotation

Gear Crank Driven Direct Vane Driven

Pelton Wheel Axial Flow (Kaplan) Mixed Flow Radial Flow (Francis)

Gear

Lobe

Figure 1

Hydrodynamic machines may be classified according to the direction of energy transfer (energy added or extracted) or the type of action (rotodynamic or positive displacement machines). Rotodynamic machines (momentum transfer machines) have a rotating part (runner, impeller or rotor) that is able to rotate continuously and freely in the fluid. This motion allows an uninterrupted flow of fluid which promotes a steadier discharge than positive displacement machines. Positive displacement machines have a moving boundary (such as a piston or a diaphragm) whereby fluid is drawn or forced into a finite space. This motion causes an intermittent or fluctuating flow and the flow rate is governed by the magnitude of the finite space of the machine and the frequency with which it is filled and emptied. The term "pump" is used when the fluid is a liquid,
Academic year: 2006-2007 Page 1 of 16

Department of Civil and Environmental Engineering CVNG 1001: Mechanics of Fluids

however, when the fluid is a gas, terms such as compressors, or fans (or blowers) are used. A compressor is a machine whose primary objective is to increase the pressure of the gas, which is accompanied by an increase in the density of the gas. A fan or blower is a machine whose primary objective is to move the gas. Static pressures remain almost unchanged, and therefore the density of the gas is also not changed.

Basic Equations for Rotodynamic Machinery The flow patterns in rotodynamic machines are three-dimensional, with significant viscous effects and flow separation patterns. However, an analytical analysis requires simplification of the actual conditions. Therefore, viscosity is neglected and an idealized two-dimensional flow is assumed throughout the rotor region. Figure 2 below defines the control volume that encompasses the impeller region, which contains a series of vanes. In the control volume, the flow enters through the inlet control surface and exits through the outlet surface.

O utlet 2 1 Inlet

b2

b1

Figure 2

A portion of the control volume, at an instant in time, is shown in Figure 3 below. The idealized velocity vectors are diagrammed at the inlet, location 1, and the outlet, location 2. The parameters used in the diagram are defined below. v = absolute velocity of fluid u = peripheral (or circumferential) velocity of blade ( u = r ) R = fluid velocity relative to blade vw = velocity of whirl, i.e., component of absolute velocity of fluid in direction tangential to the runner circumference vn = component of absolute velocity of fluid in a direction normal to the runner circumference

Academic year: 2006-2007

Page 2 of 16

Department of Civil and Environmental Engineering CVNG 1001: Mechanics of Fluids

r = radius from axis of runner = angular velocity of runner Suffix 1 refers to conditions at inlet to runner Suffix 2 refers to conditions at outlet from runner.

vw2

u2 x2
2 R2 = v2-u2

v2

vn2

1 R1 = v1-u1 v1 vn1
1 vw1

r2 r1

1 x1

u1

Axis of Rotation
Figure 3 The power passed on to the rotor from the fluid (or the power passed to the fluid from the rotor) is due to the change in tangential momentum. There may be changes of momentum in other directions also, but the corresponding forces have no moments about the axis of rotation of the rotor. Now, the torque about a given fixed axis is equal to the rate of increase of angular momentum about the axis. Therefore, the torque on the fluid must be equal to the angular momentum of the fluid leaving the rotor per unit time minus the angular momentum of the fluid entering the rotor per unit time. The angular momentum of fluid entering the control volume per second, I1, is the product & ), the tangential velocity (vw1) and the radius (r1). of the mass flow rate ( m & v w1 r1 I1 = m

Academic year: 2006-2007

Page 3 of 16

Department of Civil and Environmental Engineering CVNG 1001: Mechanics of Fluids

The angular momentum of fluid leaving the control volume per second, I2, is the product & ), the tangential velocity (vw2) and the radius (r2). of the mass flow rate ( m & v w 2 r2 I2 = m & , is the product of the fluid density, , and the flow rate, However, the mass flow rate, m Q. & = Q m And the torque, T, is given by T = Q (v w 2 r2 v w1 r1 )

The power, P, is the product of torque, T, and the angular velocity, . Therefore, P = T = Q (v w 2 r2 v w1 r1 ) = Q(v w 2 r2 v w1 r1 ) However, r1 = u1 and r2 =u2. Therefore, P = Q(v w 2 u 2 v w1u1 ) Now, v w1 = v1 cos 1 and v w 2 = v 2 cos 2 Therefore, P = Q(v 2 u 2 cos 2 v1u1 cos 1 ) The power transferred between the fluid and the rotor is given by QgH , where H is the pressure head across the rotodynamic machine. For an idealized situation, where there are no losses QgH = Q(v 2 u 2 cos 2 v1u1 cos 1 ) And H = machine. In the case of a turbine, H will be negative (as energy is extracted from the fluid) and it is common to use the reverse order of terms in the brackets, for the above equation. For (v1u1 cos 1 v2 u 2 cos 2 ) turbines, H = . g

(v2 u 2 cos 2 v1u1 cos 1 )

g

, where H is the theoretical pressure head across the

Basic Equations for Centrifugal Pumps (v2 u 2 cos 2 v1u1 cos 1 ) However, for pumps, H retains the form, H = and can be g applied to centrifugal pumps. If the whirl or tangential component of the velocity is zero at the inlet (1 = 90), then the flow is completely radial and the maximum head is obtained.

Academic year: 2006-2007

Page 4 of 16

Department of Civil and Environmental Engineering CVNG 1001: Mechanics of Fluids

Since u1 v1 cos 1 = 0 , H max = Now, x 2 =

(v2 u 2 cos 2 )
g

vn2 = v n 2 cot 2 and v w 2 = u 2 x 2 tan 2

Therefore, v w2 = u 2 v n 2 cot 2 and v 2 cos 2 = u 2 v n 2 cot 2

2 u 2 (u 2 v n 2 cot 2 ) u 2 u 2 v n 2 cot 2 v u2 = = = u 2 n 2 cot 2 g g g g 2

H max

By continuity, Q = A2 v n 2 = 2r2 b2 v n 2 , where A2 is the area perpendicular to vn2. This implies H max =
2 u2 u Q 2 cot 2 g g 2r2 b2

However, u2 = r2 and H max =

r22 2 r2 Q r 2 2 Q cot 2 = 2 cot 2 g g 2r2 b2 g g 2b2

And generally, one can write H max = a 0 a1Q , where a0 and a1 are constants for a given rotodynamic pump. This theoretical head is linearly related to the discharge through the pump; although the y-intercept, a0, is constant, the slope of the line (a1) is dependent on the blade angle, 2. Figure 4 shows the effect of the blade angle. A forward-curving blade have 2 >90, radial blades have 2 =90 whilst backward-curving blades have 2 <90.

H 2>90 2=90

2<90

Q Figure 4 Ideal Characteristic For real fluids, the theoretical head curve cannot be achieved in practice due to energy losses. The actual output power delivered can be determined using the equation QgH p

Academic year: 2006-2007

Page 5 of 16

Department of Civil and Environmental Engineering CVNG 1001: Mechanics of Fluids

where Hp is the actual head across the pump. If the overall pump efficiency, , is defined as the ratio of the output power to the input power, then the input power is given as QgH p Input Power = In addition, losses affect the H-Q curve, as shown in Figure 5. H 2>90 2=90 2<90

Q Figure 5 Typical Pump Characteristic

Similarity Laws The development and utilization of hydrodynamic machinery in engineering practice has benefited greatly from the application of dimensional analysis. It has enabled turbine and pump manufacturers to test and develop a relatively small number of turbo machines, and subsequently produce a series of commercial units that cover a broad range of head and flow demands. Geometric similarity is a pre-requisite of dynamic similarity. For fluid machines the geometric similarity must apply to all significant parts of the systemthe rotor, the entrance and discharge passages for pumps. Machines that are geometrically similar in these respects form a homologous series. To obtain the dimensionless s, for geometrically similar machines the following variables may be considered: Dimensional formula rotor diameter, here chosen as a suitable measure of [L] D the size of the machine volume rate of flow through the machine [L3T-1] Q rotational speed [T-1] N difference of head across machine, i.e., energy per [L] H unit weight Weight per unit mass [LT-2] g

Academic year: 2006-2007

Page 6 of 16

Department of Civil and Environmental Engineering CVNG 1001: Mechanics of Fluids

density of fluid viscosity of fluid Power transferred between fluid and rotor

[ML-3] [ML-1T-1] [ML2T-3]

However, since g only enters the analysis as a variable associated with H, the term gH is used, rather than g or H separately, to simplify the analysis. Gravity does not enter the problem in any other way. Using the Tabular method, the following dimensionless s can be derived for geometrically similar machines.
1 = Q ND
3

2 =

P gH 3 = 4 = 2 and 2 2 ND N 3 D 5 N D

ND 2 Alternatively 3 may be re-written as 3 = , which resembles the Reynolds number.

Similarity Laws applied to Centrifugal Pumps These similarity relationships may be used to obtain the optimum performance when a given pump is used in a different location or the performance of two different pumps. These equations are used and based on the fact that most centrifugal pumps either: 1. Have a variable speed motor, so that the pump can be changed to obtain the required head-discharge relationship while retaining the same impeller (constant D), or 2. Have a constant speed motor, so that the pump speed is fixed (constant N) and consequently different diameter impellers have to be used to vary the required head-discharge relationship. Case 1
1 2

Case 2

The relationships are known as the Affinity Laws.

Academic year: 2006-2007

Page 7 of 16

Department of Civil and Environmental Engineering CVNG 1001: Mechanics of Fluids

Q1. A pump is fitted with a variable speed motor. At 1200rpm it delivers 0.12m3/s of water. What speed of rotation would be required to increase the discharge to 0.15m3/s?

= 1500 rpm

Specific speed The specific speed of a pump may serve as a guide for pump selection. The dimensionless s may be used, and the dependence on the rotor diameter, D, is eliminated.

c1, c2, c3 and c4 are constants

Where the dimensionless parameter, Ns, is considered to be the Specific Speed. However since the acceleration due to gravity, g, is constant, the specific speed is sometimes given as the dimensional parameter, Ns.

Academic year: 2006-2007

Page 8 of 16

Department of Civil and Environmental Engineering CVNG 1001: Mechanics of Fluids

Ns Ns Ns

10 to 70 Centrifugal high head, relatively small discharge 70 to 170 Mixed Flow moderate load, moderate discharge > 110 Axial Flow low head, large discharge

Ns is defined as the speed (rpm) at which the pump operating discharges 1m3/s against 1m head (that is, N=Ns when Q=1m3/s and H=1m). The specific speed is calculated at the normal operating point of the pump (which may or may not be at the maximum efficiency), with all other variable having the corresponding values. The specific speed is the same for all similar pumps (pumps in a homologous series), regardless of size.

Performance Characteristics of Centrifugal Pumps Pumps usually run at constant speed, and of particular interest are: The variation in head, H, with the discharge, Q The variation of efficiency, , with the discharge, Q The variation of Power, P, with the discharge, Q These relationships are usually supplied by the pump manufacturer, and are provided as pump characteristic curves. Typical characteristic curves are shown in the figure below.

H ead

Efficiency Power

Discharge

Figure 6 Typical Pump Characteristic Curves

A particular machine may be tested at a fixed head while the load (and speed N) is varied, and for these results to be applicable to other pumps in the same homologous series, the characteristic curves is plotted using the dimensionless parameters:
, , and instead of Q, P, H and respectively.

Academic year: 2006-2007

Page 9 of 16

Department of Civil and Environmental Engineering CVNG 1001: Mechanics of Fluids

Selection of Centrifugal Pumps Factors that influence the selection of a pump for a given application are: The head-discharge relationship (comparison of various H-Q curves) Efficiency Power requirements Stability of the head-discharge relationships Operational Flexibility (operational conditions may change during use of the pump) Generally, a pump with a relatively steep head-discharge curve is selected to promote stability during operation of the pump. If a pump has an H-Q curve where it is horizontal (or close to horizontal) over a given discharge range, this indicates that when pumping against this head the discharge could fluctuate significantly in an uncontrolled manner causing problems with surge and water hammer. Consider the simplified pump system diagram shown in Figure 7 below.
hFD DISCH ARG E LEVEL

H D H T PUM P Vd DELIVERY PIPE

H S

Vs

SUCTIO N LEVEL hFS SUCTIO N PIPE

Figure 7 One can state that: HT = HS + hFS + HD + hFD HT total head against which the pump must discharge HS static suction lift; which is the water level in the sump to the datum level of the pump hFS head loss due to frictional losses and minor losses in the suction pipe HD static delivery lift; which is the head required to pump water to the level of the discharge point hFD head loss due to frictional losses and minor losses in the delivery pipe

Academic year: 2006-2007

Page 10 of 16

Department of Civil and Environmental Engineering CVNG 1001: Mechanics of Fluids

The total static head is the sum of HS and HD. Head losses due to frictional losses may be determined using Darcys equation where is Darcys friction factor, L is the length of the pipe, v is the mean velocity of flow in the pipe and d is the pipe diameter. Minor losses may include exit or entry losses. The pump is normally located as close as possible to the sump or suction well to reduce the frictional loss in the suction pipe. Once the system has been established for the pump, the system curve (or system characteristic) can be determined. The system curve is the relationship between head and discharge for the required system. The system curve is overlain on the pump characteristic to determine the operating point.

System load curve H ead

Pump Charcteristic Curve

O perating Point

Discharge

Figure 8

Pumps in Series and in Parallel Pumps may be used in series or in parallel to achieve the desired Head-Discharge relationship. Consider two identical pumps in series, shown in Figure 9 below.

PUMP 1

PUMP 2

Figure 9

Academic year: 2006-2007

Page 11 of 16

Department of Civil and Environmental Engineering CVNG 1001: Mechanics of Fluids

Since the discharge through pump 1 must equal the discharge through pump 2, one can write Q1 = Q2 = Q. However, the head across points A and B is twice the head for a single pump, at a given discharge. Therefore, the H-Q characteristic curve for two identical pumps in series is obtained by doubling the head, at a given discharge, shown in Figure 10 below.

H H -Q curve for two identical pumps in series (Pump 1 + Pump 2)

H -Q curve for single pump (Pump 1 )

Figure 10 Now, consider two identical pumps in parallel (at the same horizontal level), shown in Figure 11 below.
PUMP 1

A
PUMP 2

Figure 11 Pumps 1 and 2 are identical, therefore at a given discharge Q, the head delivered will be the same for each pump. Since the discharge entering at A (QT) must equal the discharge leaving at B (QT), then by continuity QT = Q1 +Q2, where Q1 and Q2 is the discharge through pump 1 and pump 2 respectively. For identical pumps Q1 = Q2 = Q, and QT =2Q. However, the head across points A and B is equal to that for a single pump, at the given discharge, Q. Therefore, the H-Q characteristic curve for two identical pumps in parallel is obtained by doubling the discharge, at a given head, shown in Figure 12 below.

Academic year: 2006-2007

Page 12 of 16

Department of Civil and Environmental Engineering CVNG 1001: Mechanics of Fluids

H H -Q curve for single pump (Pump 1 )

H -Q curve for two identical pumps in parallel (Pump 1 + Pump 2)

Q
Figure 12

Cavitation Cavitation occurs when pressure falls below vapour pressure (at the appropriate temperature). The liquid boils and bubbles form in large numbers. At locations where the pressure increases again, these bubbles implode violently. This implosion results in very high velocities as the liquid rushes in to fill the void. High pressures and high temperatures are also generated at these locations. This acting at or near solid surfaces can cause damage including fatigue failure. This phenomenon is accompanied by noise and vibration and is very destructive. Apart from physical damage, cavitation causes a reduction in the efficiency of the machine. Every effort must therefore be made to eliminate cavitation and this can be done by ensuring that the pressure is everywhere greater than the vapour pressure. Conditions are favourable for cavitation where the velocity is high or the elevation is high and particularly where both conditions occur. For centrifugal pumps, the lowest pressure occurs near the centre of the impeller where the water enters (Figure 13). Applying the energy equation between the surface of the liquid in the supply reservoir and the impeller (where the pressure is minimum), for steady conditions: where v is the velocity of flow where the pressure is minimum. However, the velocity in the supply reservoir, vo, is equal to zero and the equation reduces to:

Academic year: 2006-2007

Page 13 of 16

Department of Civil and Environmental Engineering CVNG 1001: Mechanics of Fluids

Pmin

z= H S Po Zo datum SUCTIO N LEVEL hFS

Figure 13 Dividing throughout by g, the equation has the form: and

The pressure in the supply reservoir, po, is usually atmospheric pressure, but not necessarily always. However, for a given pump design, operating under specified conditions, may be

taken as a particular portion of the head developed. That is,

This implies

c is related to the specific speed of the pump and is a property of the pump. Now for cavitation not to occur, pmin, must be greater than pv (where pv is the vapour pressure of the liquid at the operating temperature). To prevent cavitation (or ) where

Academic year: 2006-2007

Page 14 of 16

Department of Civil and Environmental Engineering CVNG 1001: Mechanics of Fluids

The above expression is known as Thoma's Cavitation Parameter. The value H is known as the Net Positive Suction Head (NPSH), and is given by:

Therefore,

To avoid cavitation one can ensure that the NPSH or is as large as possible. Techniques used to increase the NPSH include: Increase in the sump pressure (or the pressure of the supply reservoir, po) Decrease in the vapour pressure, pv, by reducing the temperature of fluid Decrease the losses in the suction pipe, hFS Decrease the static suction lift, z At the point where cavitation will occur c = and

If po, pv are considered to be constant, for a given application, and hFS is considered to be negligible, one can write

Therefore, the maximum value of z, zmax, can be obtained from

Since for this given application, zmax gives the value of z at which cavitation would occur, for this given po and pv, then cavitation is prevented. if

Academic year: 2006-2007

Page 15 of 16

Department of Civil and Environmental Engineering CVNG 1001: Mechanics of Fluids

REFERENCES Massey, B.S. 1995. Mechanics of Fluids. 6th ed. London: Chapman & Hall Hamill, L. 1995. Understanding Hydraulics. 5th ed. London: Macmillan Douglas, J.F., J.M. Gasiorek, and J.A. Swaffield. 1995. Fluid Mechanics. 3rd ed. Singapore: Longman Potter, M.C., and D.C. Wiggert. 1997. Mechanics of Fluids. 2nd ed. New Jersey: PrenticeHall

Academic year: 2006-2007

Page 16 of 16