Amercoat 3279 Datasheet

March 2012
Revision of June 2011

DESCRIPTION High Temperature Modified Silicone Aluminum
PRINCIPAL CHARACTERISTICS Resistant to dry temperature up to 1000F
Applied on prepared steel, stainless steel, or inorganic zinc
Does not require a heat cure
High solids formulation
VOC Compliant
Temperature Resistance
* Product should be sprayed in a mist coat/full coat technique when applying over inorganic zinc primers.
COLOR AND GLOSS Aluminum
Semi-gloss
BASIC DATA
Volume solids 55% 3%
VOC 3.45 lbs/gal (415 g/L)
Recommended
Dry film thickness (per coat) 0.75 2.0 mils; (15 35 microns)
1 or 2 coats
Theoretical Spread Rate @ 1 mil dft 497 ft
2
/ gallon
Components 1
Shelf Life 2 years from date of manufacture
SURFACE PREPARATION
Steel Remove weld spatter, protrusions, and laminations in steel. Grind welds smooth in
accordance with NACE RP-0178. Round off sharp edges. Remove all surface con-
taminants, oil and grease in accordance with SSPC SP-1.
Abrasive blast with an angular abrasive to an SSPC SP-10 cleanliness or higher.
Achieve a surface profile of 1.0-1.5 mils. Apply Amercoat 3279 as soon as possible
to avoid rusting of blasted surfaces.
Stainless Steel Abrasive blast with a hard angular abrasive to achieve a uniform and dense anchor
profile of 1.0-1.5 mils.
Inorganic Zinc Surfaces Surface must be clean, dry and free of zinc salts. A mist coat / full coat application
technique may be required to prevent application bubbling.
ENVIRONMENTAL CONDITIONS
Ambient temperatures* 32F to 104F (0C to 40C)
Material temperatures 50F to 90F (10C to 32C)
Relative humidity 0 85%
Surface temperature 32F to 104F (0C to 40C) Surface temperature must remain at least 5F above the
dew point temperatures.
General air quality Area should be sheltered from airborne particulates and pollutants. Provide shelter to
prevent wind from affecting spray patterns.
AMERCOAT
3279
page 1/3
First coat Second Coat Temperature Resistance
Amercoat 3279
1.0 2.0 mils
N/A 1000F
Amercoat 3279
1.5 2.0 mils
Amercoat 3279
1.5 2.0 mils
750F
Dimetcote 9-series*
2.0 3.0 mils
Amercoat 3279
1.5 2.0 mils
750F
INSTRUCTIONS FOR USE
Mixing Mix with a pneumatic air mixing at moderate speeds to homogenize the container.
Airless spray 33:1 pump or larger, 0.017 fluid tip
Air spray Use a 2.0-2.6 mm fluid tip at approximately 40 psi fluid pressure. An agitated pressure
pot is recommended. Separate air and fluid regulators are essential. Ensure there is a
moisture and oil trap in the main air line.
Brush & roll Spray application is recommended as the best method to obtain a closed film within the
film thickness limits. Rolling may leave visible patterns in the film. A short nap, solvent
resistant roller is required.
Use a high quality natural bristle brush. Ensure brush is well loaded to avoid air entrain-
ment. Brush application is limited to small touch up areas of a few square inches.
Thinner Amercoat 65
Cleaning solvent Amercoat 12 Cleaner or Amercoat 65 thinner
Safety precautions For paint and recommended thinners see safety sheet 1430, 1431 and relevant material
safety data sheets
This is a solvent borne paint and care should be taken to avoid inhalation of spray mist
or vapor as well as contact between the wet paint and exposed skin or eyes.
DRY/CURE TIMES*
* Product is not designed for heavy mechanical abuse. Care should be taken during shipping and handling.
Make any necessary repairs prior to service. Coating film will become more durable after exposure to high
temperatures.
AVAILABILITY
Packaging Available in 1-gallon and 5-gallon units
Product codes SPEC3279 Amercoat 3279
Worldwide statement While it is always the aim of PPG Protective & Marine Coatings to supply the same product
on a worldwide basis, slight modification of the product is sometimes necessary to comply
with local or national rules/circumstances. Under these circumstances an alternative product
data sheet is used.
WARRANTY STATEMENT
PPG warrants (i) its title to the products, (ii) that the quality of the product(s) conform to PPGs specifications for such products
in effect at the time of manufacture and (iii) that the products shall be delivered free of the rightful claim of any third person for
infringement of any U.S. patent covering the products. THESE ARE THE ONLY WARRANTIES PPG MAKES AND ALL
OTHER EXPRESS OR IMPLIED WARRANTIES, UNDER STATUTE OR ARISING OTHERWISE IN LAW, FROM A COURSE
OF DEALING OR USAGE OF TRADE, INCLUDING WITHOUT LIMITATION, ANY OTHER WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE OR USE, ARE DISCLAIMED BY PPG.
AMERCOAT 3279
page 2/3
Temperature F/C 50/10 70/21 90/32
Dry to handle (hrs) 8 6 5
Dry to recoat (hrs) 3 2 1.5
Cure to high temperature
service (hrs)
7 10 13
Cure to mild abrasion resistance 48 24 16
Maximum recoat (days) Unlimited until heated above ambient conditions
page 3/3
AMERCOAT 3279
The information in this data sheet is based upon laboratory tests PPG believes to be accurate and is intended for guidance
only. PPG may modify the information contained herein at any time as a result of practical experience and continuous product
development. All recommendations or suggestions relating to the use of PPG products, whether in technical documentation, or
in response to a specific inquiry, or otherwise, are based on data, which to the best of PPGs knowledge, are reliable. The
products and information are designed for users having the requisite knowledge and industrial skills and it is the end-users
responsibility to determine the suitability of the product for its intended use.
PPG has no control over either the quality or condition of the substrate, or the many factors affecting the use and application of
the product. Therefore, PPG does not accept any liability arising from loss, injury or damage resulting from such use or the
contents of this data sheet (unless there are written agreements stating otherwise).
This data sheet supersedes all previous versions and it is the users responsibility to ensure that this data sheet is current prior
to using the product. The English text of this document shall prevail over any translation thereof.
LIMITATION OF LIABILITY
The information in this data sheet is based upon laboratory tests we believe to be accurate and is intended for guidance only. All
recommendations or suggestions relating to the use of the products made by PPG Protective & Marine Coatings, whether in
technical documentation, or in response to a specific enquiry, or otherwise, are based on data which to the best of our knowledge
are reliable. The products and information are designed for users having the requisite knowledge and industrial skills and it is the
end-users responsibility to determine the suitability of the product for its intended use.
PPG Protective & Marine Coatings has no control over either the quality or condition of the substrate, or the many factors affecting
the use and application of the product. PPG Protective & Marine Coatings does therefore not accept any liability arising from loss,
injury or damage resulting from such use or the contents of this data sheet (unless there are written stating otherwise).
The data contained herein are liable to modification as a result of practical experience and continuous product development.
This data sheet replaces and annuls all previous issues and it is therefore the users responsibility to ensure that this sheet is current
prior to using the product. The current data sheets are maintained at www.ppgpmc.com
The English text of this document shall prevail over any translation thereof.

Amercoat 3279 Datasheet

Uploaded by

Copyright:

Available Formats

Amercoat 3279 Datasheet

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Amercoat 3279 Datasheet

Uploaded by

Copyright:

Available Formats

March 2012

Revision of June 2011

You might also like