64Mb Synchronous DRAM based on 1M x 4Bank x16 I/O Document Title

4Bank x 1M x 16bits Synchronous DRAM

Revision History
Revision No. 0.1 1.0 History Initial Draft Final Version Draft Date Jan. 2007 Apr. 2007 Remark Preliminary

This document is a general product description and is subject to change without notice. Hynix does not assume any responsibility for use of circuits described. No patent licenses are implied. Rev. 1.0 / Apr. 2007 1

Synchronous DRAM Memory 64Mbit (4Mx16bit) HY57V641620F(L/S)TP Series

DESCRIPTION
The Hynix HY57V641620F(L/S)TP series is a 67,108,864bit CMOS Synchronous DRAM, ideally suited for the memory applications which require wide data I/O and high bandwidth. HY57V641620F(L/S)TP is organized as 4banks of 1,048,576x16. HY57V641620F(L/S)TP is offering fully synchronous operation referenced to a positive edge of the clock. All inputs and outputs are synchronized with the rising edge of the clock input. The data paths are internally pipelined to achieve very high bandwidth. All input and output voltage levels are compatible with LVTTL. Programmable options include the length of pipeline (Read latency of 2 or 3), the number of consecutive read or write cycles initiated by a single control command (Burst length of 1,2,4,8 or full page), and the burst count sequence(sequential or interleave). A burst of read or write cycles in progress can be terminated by a burst terminate command or can be interrupted and replaced by a new burst read or write command on any cycle. (This pipelined design is not restricted by a '2N' rule)

FEATURES
Voltage: VDD, VDDQ 3.3V supply voltage All device pins are compatible with LVTTL interface 54 Pin TSOPII (Lead or Lead Free Package) All inputs and outputs referenced to positive edge of system clock Data mask function by UDQM, LDQM Internal four banks operation Burst Read Single Write operation Programmable CAS Latency; 2, 3 Clocks Auto refresh and self refresh 4096 Refresh cycles / 64ms Programmable Burst Length and Burst Type - 1, 2, 4, 8 or full page for Sequential Burst - 1, 2, 4 or 8 for Interleave Burst

ORDERING INFORMATION
Part Number HY57V641620F(L/S)TP-5 HY57V641620F(L/S)TP-6 HY57V641620F(L/S)TP-7 HY57V641620F(L/S)TP-H HY57V641620F(L/S)TP-5I HY57V641620F(L/S)TP-6I HY57V641620F(L/S)TP-7I HY57V641620F(L/S)TP-HI Clock Frequency 200MHz 166MHz 143MHz 133MHz 200MHz 166MHz 143MHz 133MHz 4Banks x 1Mbits x16 LVTTL -40oC to 85 0oC to 70 54 Pin TSOP (Lead Free) Organization Interface Operation Temp. Package

Note: 1. HY57V641620FTP Series: Normal power 2. HY57V641620FLTP Series: Low power 3. HY57V641620FSTP Series: Super Low power Rev. 1.0 / Apr. 2007 2

Synchronous DRAM Memory 64Mbit (4Mx16bit) HY57V641620F(L/S)TP Series

PIN ASSIGNMENTS

VDD DQ0 VDDQ DQ1 DQ2 VSSQ DQ3 DQ4 VDDQ DQ5 DQ6 VSSQ DQ7 VDD LDQM /WE /CAS /RAS /CS BA0 BA1 A10/AP A0 A1 A2 A3 VDD

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27

54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28

VSS DQ15 VSSQ DQ14 DQ13 VDDQ DQ12 DQ11 VSSQ DQ10 DQ9 VDDQ DQ8 VSS NC UDQM CLK CKE NC A11 A9 A8 A7 A6 A5 A4 VSS

54 Pin TSOPII 400mil x 875mil 0.8mm pin pitch

Rev. 1.0 / Apr. 2007

Synchronous DRAM Memory 64Mbit (4Mx16bit) HY57V641620F(L/S)TP Series

PIN DESCRIPTION
SYMBOL CLK TYPE Clock DESCRIPTION The system clock input. All other inputs are registered to the SDRAM on the rising edge of CLK Controls internal clock signal and when deactivated, the SDRAM will be one of the states among power down, suspend or self refresh Enables or disables all inputs except CLK, CKE, UDQM and LDQM Selects bank to be activated during RAS activity Selects bank to be read/written during CAS activity Row Address: RA0 ~ RA11, Column Address: CA0 ~ CA7 Auto-precharge flag: A10 RAS, CAS and WE define the operation Refer function truth table for details Controls output buffers in read mode and masks input data in write mode Multiplexed data input / output pin Power supply for internal circuits and input buffers Power supply for output buffers No connection

CKE CS BA0, BA1

Clock Enable Chip Select Bank Address

A0 ~ A11

Address Row Address Strobe, Column Address Strobe, Write Enable Data Input/Output Mask Data Input / Output Power Supply / Ground Data Output Power / Ground No Connection

RAS, CAS, WE

UDQM, LDQM DQ0 ~ DQ15 VDD / VSS VDDQ / VSSQ NC

Rev. 1.0 / Apr. 2007

Synchronous DRAM Memory 64Mbit (4Mx16bit) HY57V641620F(L/S)TP Series

FUNCTIONAL BLOCK DIAGRAM

1Mbit x 4banks x 16 I/O Synchronous DRAM

Self refresh logic & timer CLK CKE State Machine CS RAS CAS Column Active WE U/LDQM Row Active

Internal Row Counter 1Mx16 BANK 3 Row Pre Decoder 1Mx16 BANK 2 1Mx16 BANK 1 1Mx16 BANK 0 DQ0 I/O Buffer & Logic Sense AMP & I/O Gate X-Decoder X-Decoder X-Decoder X-Decoder

Refresh

Memory Cell Array

Column Pre Decoder Y-Decoder

DQ15

Bank Select

Column Add Counter

A0 A1 Address Buffers

Address Register

Burst Counter Pipe Line Control

A11 BA1 BA0

Mode Register

CAS Latency

Data Out Control

Rev. 1.0 / Apr. 2007

Synchronous DRAM Memory 64Mbit (4Mx16bit) HY57V641620F(L/S)TP Series

BASIC FUNCTIONAL DESCRIPTION

Mode Register
BA1 0 BA0 0 A11 0 A10 0 A9 OP Code A8 0 A7 0 A6 A5 CAS Latency A4 A3 BT A2 A1 Burst Length A0

OP Code
A9 0 1 Write Mode Burst Read and Burst Write Burst Read and Single Write

Burst Type
A3 0 1 Burst Type Sequential Interleave

CAS Latency
A6 0 0 0 0 1 1 1 1 A5 0 0 1 1 0 0 1 1 A4 0 1 0 1 0 1 0 1 CAS Latency Reserved Reserved 2 3 Reserved Reserved Reserved Reserved

Burst Length
A2 0 0 0 0 1 1 1 1 A1 0 0 1 1 0 0 1 1 A0 0 1 0 1 0 1 0 1 Burst Length A3 = 0 1 2 4 8 Reserved Reserved Reserved Full Page A3=1 1 2 4 8 Reserved Reserved Reserved Reserved

Rev. 1.0 / Apr. 2007

Synchronous DRAM Memory 64Mbit (4Mx16bit) HY57V641620F(L/S)TP Series

ABSOLUTE MAXIMUM RATING

Parameter Symbol Rating 0 ~ 70 (Commercial part) -40 ~ 85 (Industrial part) -55 ~ 125 -1.0 ~ 4.6 -1.0 ~ 4.6 50 1 260 . 10
o

Unit
o

C C C

Ambient Temperature

TA

o o

Storage Temperature Voltage on Any Pin relative to VSS Voltage on VDD supply relative to VSS Short Circuit Output Current Power Dissipation Soldering Temperature . Time

TSTG VIN, VOUT VDD, VDDQ IOS PD TSOLDER

V V mA W C . Sec

DC OPERATING CONDITION (TA= 0 to 70oC / -40 to 85oC)

Parameter Power Supply Voltage Input High Voltage Input Low Voltage Symbol VDD, VDDQ VIH VIL Min 3.0 2.0 -0.3 Typ 3.3 3.0 Max 3.6 VDDQ + 0.3 0.8 Unit V V V Note 1 1, 2 1, 3

Note: 1. All voltages are referenced to VSS = 0V 2. VIH(max) is acceptable 5.6V AC pulse width with <=3ns of duration. 3. VIL(min) is acceptable -2.0V AC pulse width with <=3ns of duration.

AC OPERATING TEST CONDITION (TA= 0 to 70oC / -40 to 85oC, VDD=3.30.3V, VSS=0V)

Parameter AC Input High/Low Level Voltage Input Timing Measurement Reference Level Voltage Input Rise/Fall Time Output Timing Measurement Reference Level Voltage Output Load Capacitance for Access Time Measurement
Note: 1.
Vtt=1.4V Vtt=1.4V

Symbol VIH / VIL Vtrip tR / tF Voutref CL

Value 2.4 / 0.4 1.4 1 1.4 30

Unit V V ns V pF

Note

RT=500

RT=50

Output

Output

Z0 = 50

30pF

30pF

DC Output Load Circuit

AC Output Load Circuit

Rev. 1.0 / Apr. 2007

Synchronous DRAM Memory 64Mbit (4Mx16bit) HY57V641620F(L/S)TP Series

CAPACITANCE (f=1MHz, VDD=3.3V)

Parameter CLK Input capacitance A0 ~ A11, BA0, BA1, CKE, CS, RAS, CAS, WE, LDQM, UDQM DQ0 ~ DQ15 Pin Symbol CI1 CI2 CI/O Min 2.0 2.5 3.0 Max 4.0 5.0 5.5 Unit pF pF pF

Data input / output capacitance

DC CHARACTERRISTICS I (TA= 0 to 70oC / -40 to 85oC)

Parameter Input Leakage Current Output Leakage Current Output High Voltage Output Low Voltage Symbol ILI ILO VOH VOL Min -1 -1 2.4 Max 1 1 0.4 Unit uA uA V V Note 1 2 IOH = -4mA IOL = +4mA

Note: 1. VIN = 0 to 3.3V, All other balls are not tested under VIN =0V 2. DOUT is disabled, VOUT=0 to 3.6

Rev. 1.0 / Apr. 2007

Synchronous DRAM Memory 64Mbit (4Mx16bit) HY57V641620F(L/S)TP Series

DC CHARACTERISTICS II (TA= 0 to 70oC / -40 to 85oC)

Parameter Symbol Test Condition Burst length=1, One bank active tRC tRC(min), IOL=0mA CKE VIL(max), tCK = 15ns CKE VIL(max), tCK = CKE VIH(min), CS VIH(min), tCK = 15ns Input signals are changed one time during 2clks. All other pins VDD-0.2V or 0.2V CKE VIH(min), tCK = Input signals are stable. CKE VIL(max), tCK = 15ns CKE VIL(max), tCK = CKE VIH(min), CS VIH(min), tCK = 15ns Input signals are changed one time during 2clks. All other pins VDD-0.2V or 0.2V CKE VIH(min), tCK = Input signals are stable. tCK tCK(min), IOL=0mA All banks active tRC tRC(min), All banks active Normal Self Refresh Current IDD6 CKE 0.2V Low power Super Low power Speed 5 6 7 H Unit Note

Operating Current

IDD1

120 110 100 100 2 2

mA mA mA

Precharge Standby Cur- IDD2P rent IDD2PS in Power Down Mode

Precharge Standby Cur- IDD2N rent in Non Power Down Mode IDD2NS Active Standby Current in Power Down Mode IDD3P IDD3PS

18 mA 15 3 3

mA

Active Standby Current in Non Power Down Mode

IDD3N

40 mA 35 120 110 100 100 170 160 150 150 1 400 300 mA mA mA 3 uA uA 3, 4 1 2

IDD3NS Burst Mode Operating Current Auto Refresh Current IDD4 IDD5

Note: 1. IDD1 and IDD4 depend on output loading and cycle rates. Specified values are measured with the output open 2. Min. of tRRC (Refresh RAS cycle time) is shown at AC CHARACTERISTICS II 3. HY57V641620FTP Series: Normal Power HY57V641620FLTP Series: Low Power HY57V641620FSTP Series: Super Low Power

Rev. 1.0 / Apr. 2007

Synchronous DRAM Memory 64Mbit (4Mx16bit) HY57V641620F(L/S)TP Series

AC CHARACTERISTICS I (AC operating conditions unless otherwise noted)

Parameter CL = 3 CL = 2 Symbol tCK3 tCK2 tCHW tCLW CL = 3 CL = 2 tAC3 tAC2 tOH tDS tDH tAS tAH tCKS tCKH tCS tCH 5 Min 5.0 10 1.75 1.75 2.0 1.5 0.8 1.5 0.8 1.5 0.8 1.5 0.8 1.0 Max 1000 4.5 6.0 4.5 6.0 Min 6.0 10 2.0 2.0 2.0 1.5 0.8 1.5 0.8 1.5 0.8 1.5 0.8 1.0 6 Max 1000 5.4 6.0 5.4 6.0 Min 7.0 10 2.0 2.0 2.5 1.5 0.8 1.5 0.8 1.5 0.8 1.5 0.8 1.5 7 Max 1000 5.4 6.0 5.4 6.0 Min 7.5 10 2.5 2.5 2.5 1.5 0.8 1.5 0.8 1.5 0.8 1.5 0.8 1.5 H Max 1000 5.4 6.0 5.4 6.0 Unit Note

System Clock Cycle Time Clock High Pulse Width Clock Low Pulse Width Access Time From Clock Data-out Hold Time Data-Input Setup Time Data-Input Hold Time Address Setup Time Address Hold Time CKE Setup Time CKE Hold Time Command Setup Time Command Hold Time

ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns 1 1 1 1 1 1 1 1 1 1 2

CLK to Data Output in Low-Z Time tOLZ CLK to Data Output in High-Z Time CL = 3 CL = 2 tOHZ3 tOHZ2

Note: 1. Assume tR / tF (input rise and fall time) is 1ns. If tR & tF > 1ns, then [(tR+tF)/2-1]ns should be added to the parameter. 2. Access time to be measured with input signals of 1V/ns edge rate, from 0.8V to 0.2V. If tR > 1ns, then (tR/2-0.5)ns should be added to the parameter.

Rev. 1.0 / Apr. 2007

10

Synchronous DRAM Memory 64Mbit (4Mx16bit) HY57V641620F(L/S)TP Series

AC CHARACTERISTICS II (AC operating conditions unless otherwise noted)

Parameter RAS Cycle Time RAS Cycle Time RAS to CAS Delay RAS Active Time RAS Precharge Time RAS to RAS Bank Active Delay CAS to CAS Delay Operation Symbol tRC 5 Min 55 55 15 38.7 15 10 1 0 2 Max 100K Min 60 60 18 42 18 12 1 0 2 6 Max 100K Min 63 63 20 42 20 14 1 0 2 tDPL + tRP 2 0 2 3 2 1 1 64 2 0 2 3 2 1 1 64 2 0 2 3 2 1 1 64 2 0 2 3 2 1 1 64 CLK CLK CLK CLK CLK CLK CLK ms 1 7 Max 100K Min 63 63 20 42 20 15 1 0 2 H Max 120K Unit Note ns ns ns ns ns ns CLK CLK CLK

Auto Refresh tRRC tRCD tRAS tRP tRRD tCCD

Write Command to Data-In DetWTL lay Data-in to Precharge Command tDPL Data-In to Active Command DQM to Data-Out Hi-Z DQM to Data-In Mask MRS to New Command Precharge to Data CL = 3 Output High-Z CL = 2 Power Down Exit Time Self Refresh Exit Time Refresh Time tDAL tDQZ tDQM tMRD tPROZ3 tPROZ2 tDPE tSRE tREF

Note: 1. A new command can be given tRRC after self refresh exit.

Rev. 1.0 / Apr. 2007

11

Synchronous DRAM Memory 64Mbit (4Mx16bit) HY57V641620F(L/S)TP Series

COMMAND TRUTH TABLE

Command Mode Register Set No Operation Bank Active Read Read with charge Write Write with charge AutopreH X L H L L X CA AutopreH X L H L H X CA CKEn-1 H H H CKEn X X X CS L H L L RAS L X H L CAS L X H H WE L X H H DQM X X X RA L H L H H H X L L H L X X L X X X A9 ball High (Other balls OP code) MRS Mode V V ADDR A10/AP OP code X V BA Note

Precharge All Banks Precharge Bank Burst Stop DQM Auto Refresh Burst-Read-SingleWRITE Entry Self Refresh1 Exit selected

X V

H H H H H L

H X

X V

H X L H

L L L H L H L H L H L

L L L X H X H X H X V X

L L L X H X H X H X V

H L H X H X H X H X V

X X X X

Entry Precharge power down Exit

X X X

Clock Suspend

Entry Exit

H L

L H

X X

Rev. 1.0 / Apr. 2007

12

Synchronous DRAM Memory 64Mbit (4Mx16bit) HY57V641620F(L/S)TP Series

PACKAGE INFORMATION
400mil 54pin Thin Small Outline Package

UNIT : mm(inch)

11.938(0.4700) 11.735(0.4620) 22.327(0.8790) 22.149(0.8720) 10.262(0.4040) 10.058(0.3960) 0.150(0.0059) 0.050(0.0020) 1.194(0.0470) 0.991(0.0390)

0.80(0.0315)BSC

0.400(0.016) 0.300(0.012)

5deg 0deg

0.597(0.0235) 0.406(0.0160)

0.210(0.0083) 0.120(0.0047)

Rev. 1.0 / Apr. 2007

13