Scribd
Upload
7K views

LOGO! Analog Input PT100 Manual

The analog expansion module AM2 PT100 is equipped with two inputs, each one for connecting a Pt100 thermocouple. It converts the resistive value of a connected thermocouple to a temperature measurement range of -50 degC. +200 degC with a resolution of 1000 measuring steps. The expansion module is compatible with all LOGO! devices (as of.-0BA3)

Uploaded by

Khurram
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
7K views

LOGO! Analog Input PT100 Manual

The analog expansion module AM2 PT100 is equipped with two inputs, each one for connecting a Pt100 thermocouple. It converts the resistive value of a connected thermocouple to a temperature measurement range of -50 degC. +200 degC with a resolution of 1000 measuring steps. The expansion module is compatible with all LOGO! devices (as of.-0BA3)

Uploaded by

Khurram
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

Product information for

LOGO! Manual

6ED1 050-1AA00-0BE4, Release 07/2001

In this product information...


...you will find supplementary information on analog
LOGO! Expansion module AM2 PT100 (order no.
6ED1 055-1MD00-0BA0). Please refer to the LOGO!
Manual for information not found in this product informa-
tion.

Short description of the expansion module AM2 PT100


The analog expansion module AM2 PT100 is equipped
with two inputs, each one for connecting a Pt100 ther-
mocouple.
The analog expansion module AM2 PT100 converts the
resistive value of a connected Pt100 thermocouple to a
temperature measurement range of –50 °C ... +200 °C
with a resolution of 1000 measuring steps.
The analog expansion module AM2 PT100 is compati-
ble with all LOGO! devices (as of ...–0BA3).

Copyright 2002 by Siemens AG


A5E00167931-01
This is the structure of the expansion module AM2 PT100

5 6
5 1
4 4
L+ M L+ M

4
7

35

90
RUN/STOP

1 8
PE

M1+ IC1 M1- M2+ IC2 M2–

2
36 53

1 5 Mechanical encoding – 8 PE terminal for ground


Power supply
Pins and shielding termina-
2 Inputs tion of the analog mea-
6 Mechanical encoding –
3 Status display RUN/ surement line.
Sockets
STOP
4 Expansion interface 7 Slides

General technical data

Criteria Values
Dimensions WxHxD 36 x 90 x 55 mm
Weight approx. 90 g
Mounting on 35 mm
DIN rail2 unit widths or wall
mounting
Further general technical data is found in the Logo! Manual

Product information for LOGO! manual


2 A5E00167931-01
Technical data of LOGO! AM2 PT100

LOGO! AM2 PT100


Power supply
Input voltage 12/24 VDC
Permitted range 10.8 ... 15.6 V DC
20.4 ... 28.8 V
Current consumption 25 ... 50 mA
Voltage loss buffering typically 5 ms
Power loss at
S 12 V 0.3 ... 0.6 W
S 24 V 0.6 ... 1.2 W
Electrical isolation no
Reverse polarity protection yes
PE terminal Ground connection and
measurement line shielding
Sensor inputs
Number 2
Type Thermocouple Pt100
Sensor connection
S 2-wire technique yes
S 2-wire technique yes
Measurement range –50 °C ... +200 °C
–58 °F ... +392 °F

Product information for LOGO! manual


A5E00167931-01 3
LOGO! AM2 PT100
Setting of the measurement
value display on the basic
module:
S 1 ° C steps Offset: –200, Gain: 25
S 0,25 °C steps (rounded Offset: –200, Gain: 250
to one decimal point)
S 1 ° F steps Offset: –128, Gain: 45
S 0,25 °F steps Offset: –128, Gain: 450
(rounded to one decimal
point)
Characteristic curve lineari- no
zation
Measurement current Ic 1.1 mA
Measuring rate depends on the assembly
typically 50 ms
Resolution 0.25 °C
Error limits of the measurement limit va-
lue:
S 0 °C ... +200 °C +/–1.0 %
S –50 °C ... +200 °C +/–1.5 %
Electrical isolation no
Cable length (shielded) 10 m
Interference suppression 55 Hz

Product information for LOGO! manual


4 A5E00167931-01
Options of connecting a Pt100 thermocouple
You can connect a Pt100 thermocouple to the module in
2- or 3-wire technique.
When you select the 2-wire technique, you must jum-
per terminals M1+ and IC1 or M2+ and IC2. Measure-
ment errors due to measurement cable resistance will
not be compensated with this type of connection.1 W
cable resistance is proportional to a measurement error
of +2.5Ă°C.
With 3-wire connection, the influence of the cable
length (resistance) on the measurement result will be
suppressed.

2-wire technique 3-wire technique


L+ M L+ M L+ M L+ M

RUN/STOP RUN/STOP

PE PE

M1+ IC1 M1- M2+ IC2 M2– M1+ IC1 M1- M2+ IC2 M2–

Pt100 Pt100

Product information for LOGO! manual


A5E00167931-01 5
Note
Operation of the LOGO! expansion module AM2 PT100 on
an ungrounded (floating potential) power supply may result
in severe fluctuation of the displayed temperature value.
In this case connect the negative output / power supply
ground to the shielded measurement cables of the thermo-
couple.

Programming the AM2 PT100 under LOGO!Soft Comfort


V3.x
You can program the expansion module AM2 PT100 as
usual under LOGO!Soft Comfort => Version 3.0. As of
Version 3.1 plus Service Pack you can program the ex-
pansion module AM2 PT100 menu controlled.
Up–to–date information and Service Packs are found
free of charge under the SIEMENS AG Internet URL:
http://www.ad.siemens.de/logo/index_00.htm

Product information for LOGO! manual


6 A5E00167931-01

You might also like