Scribd Logo
Upload

Welcome to Scribd!

  • 290 views

    Figure 2: Wiring Diagram: Van'S Aircraft, Inc

    Uploaded by

    Mark Evan Salutin
    The document provides instructions for installing a WH-RV12-DUALDISPLAY harness on a Van's Aircraft RV-12. It involves removing an existing COM radio to aid in routing wires, installing the new harness through snap bushings, cutting and splicing wires between the new and existing harnesses based on wire color and pin locations, attaching backshells, and tying everything together. Key steps include identifying wires using a multimeter, crimping corresponding wires together in butt splices, and attaching labels to identify wiring.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    Figure 2: Wiring Diagram: Van'S Aircraft, Inc

    Uploaded by

    Mark Evan Salutin
    290 views1 page
    The document provides instructions for installing a WH-RV12-DUALDISPLAY harness on a Van's Aircraft RV-12. It involves removing an existing COM radio to aid in routing wires, installing the new harness through snap bushings, cutting and splicing wires between the new and existing harnesses based on wire color and pin locations, attaching backshells, and tying everything together. Key steps include identifying wires using a multimeter, crimping corresponding wires together in butt splices, and attaching labels to identify wiring.

    Original Description:

    RV-12

    Original Title

    43-05

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides instructions for installing a WH-RV12-DUALDISPLAY harness on a Van's Aircraft RV-12. It involves removing an existing COM radio to aid in routing wires, installing the new harness through snap bushings, cutting and splicing wires between the new and existing harnesses based on wire color and pin locations, attaching backshells, and tying everything together. Key steps include identifying wires using a multimeter, crimping corresponding wires together in butt splices, and attaching labels to identify wiring.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    290 views1 page

    Figure 2: Wiring Diagram: Van'S Aircraft, Inc

    Uploaded by

    Mark Evan Salutin
    The document provides instructions for installing a WH-RV12-DUALDISPLAY harness on a Van's Aircraft RV-12. It involves removing an existing COM radio to aid in routing wires, installing the new harness through snap bushings, cutting and splicing wires between the new and existing harnesses based on wire color and pin locations, attaching backshells, and tying everything together. Key steps include identifying wires using a multimeter, crimping corresponding wires together in butt splices, and attaching labels to identify wiring.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    VAN'S AIRCRAFT, INC.

    NOTE: Check that the avionics master switch is in the off position. Opening the 37 PIN D180 D-SUB backshell is not required if a multimeter is available. When cutting wires to length leave enough to allow the EFIS to be removed from the panel. After a WH-RV12-DYNON harness wire is cut its halves will be referred to as "left" (for WH-RV12-DYNON AV Control Board 12, 37 Pin d-sub) side or "right" (for WH-RV12-DYNON EFIS 25 pin d-sub) side. Step 1 (POSTCONST): Remove the AV GARMIN SL-40 COM Radio(not shown) from its tray to aid in routing wires. Step 1 (PRECONST): Proceed to Step 2. Step 2: Install the WH-RV12-DUALDISPLAY harness through the snap bushings in F-1202K-L & -R Inst Stack Supports. Strip the ends of the harness and position them at the splice location depicted in Figure 1. Step 3: Unplug the WH-RV12-DYNON harness EFIS 25 PIN D-SUB connector from the back of the IF DYNON DEK 180-12 Dynon EFIS/EMS. Step 4: Locate the RED 20 gauge wire in the WH-RV12-DYNON harness, cut it in the region of the splice and strip each end. ES 320562, 2 PL. Step 5: Crimp the end of the left half of the RED 20 gauge wire in the WH-RV12-DYNON harness to the butt splice called out in Figure 2. Insert the corresponding color wire from the WH-RV12-DUALDISPLAY harness into the other end of the butt splice along with the end of the right half of the RED 20 gauge wire and crimp them together. Step 6: Repeat Steps 4 and 5 for the BLK and BLU wires. 1X Step 7: Locate the two GRN wires in the WH-RV12-DYNON harness. Step 8: Identify the correct GRN wire by checking for continuity using a multimeter (or equivalent) between the corresponding pin at the WH-RV12-DYNON harness EFIS 25 PIN D-SUB connector and a needle inserted through the insulation of one of the GRN wires at the intended splice location. See pin 4 in Figure 2. Once identified cut the GRN(pin 4) wire and strip each end. Step 9: Repeat Step 5 for the GRN wire. Step 10: Identify and cut the WHT wire corresponding to pin 10 in the WH-RV12-DYNON harness in a manner similar to that of Step 8. Step 11: Crimp the end of the left half of the WHT(pin 10) WH-RV12-DYNON harness wire to the butt splice called out in Figure 2. Insert the wire labeled F211(WHT) from the WH-RV12-DUALDISPLAY harness into the other end of the butt splice along with the end of the right half of the WHT(pin 10) WH-RV12-DYNON harness wire and crimp them together. Step 12: Identify and cut the WHT wire corresponding to pin 22 in the WH-RV12-DYNON harness in a manner similar to that of Step 8. Step 13: Crimp the end of the left half of the WHT(pin 22) WH-RV12-DYNON harness wire to the butt splice called out in Figure 2. Insert the wire labeled F212(WHT) from the WH-RV12-DUALDISPLAY harness into the other end of the butt splice along with the end of the right half of the WHT(pin 22) WH-RV12-DYNON harness wire and crimp them together. Step 14: Tie wrap the WH-RV12-DUALDISPLAY harness to the WH-RV12-DYNON harness. Step 15: Attach an ES 25 PIN BACKSHELL to the WH-RV12-DUALDISPLAY harness. See Section 5 for Backshell installation. F-1202K-R WH-RV12-DUALDISPLAY (EFIS 25 PIN D-SUB) ES 25 PIN BACKSHELL UP PIN 13: (WHT/BLU) PIN 1: (RED) PIN 3: (BLK) PIN 4: (GRN) PIN 22: (WHT) PIN 10: (WHT) PIN 23: (WHT/GRN) PIN 11: (WHT/GRN) PIN 5: (BLU) PIN 3: (BLK) PIN 4: (GRN) PIN 10: (WHT) PIN 1: (RED) PIN 18: (GRN) PIN 5: (BLU) PIN 22: (WHT) PIN 12: (WHT/BLU) WH-RV12-DYNON (EFIS 25 PIN FEMALE D-SUB) WH-RV12-DUALDISPLAY (EFIS 25 PIN FEMALE D-SUB)

    FWD

    LEFT

    F210

    P207

    F209

    F208

    F211

    F212

    TO: WH-RV12-DYNON (AV CONTROL BOARD 12, 37 PIN D-SUB) WH-RV12-DYNON (EFIS 25 PIN D-SUB) WH-RV12-DYNON (EMS 37 PIN D-SUB) IF DYNON DEK 180-12

    ES 320559, 4 PL.

    FIGURE 2: WIRING DIAGRAM


    (D-SUB REAR VIEW / PIN INSERTION SIDE)

    F-1202B F-1202K-L WH-RV12DUALDISPLAY

    ~5

    FIGURE 1: EFIS WIRING HARNESS INSTALLATION


    SOME PARTS AND COMPONENTS OMITTED FOR CLARITY

    SPLICE LOCATION MEASURED FROM BACKSHELL

    WH-RV12-DYNON

    WH-RV12-DYNON (AV CONTROL BOARD 12 37 PIN D-SUB)

    DATE: 02/22/10 REVISION:

    RV-12

    PAGE

    43-05

    You might also like