Scribd
Upload
613 views3 pages

Nstreme Dual Step by Step

This document provides step-by-step instructions for configuring nstreme dual on two MikroTik devices. It involves enabling wireless cards, assigning IP addresses, creating bridge interfaces, adding ports, setting the wireless cards to nstreme mode, creating nstreme dual interfaces, setting frequencies and radios, and specifying the remote MAC addresses. The MAC addresses are set on each device to allow the nstreme dual interfaces to communicate over the wireless bridge.

Uploaded by

nuro123
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
613 views3 pages

Nstreme Dual Step by Step

This document provides step-by-step instructions for configuring nstreme dual on two MikroTik devices. It involves enabling wireless cards, assigning IP addresses, creating bridge interfaces, adding ports, setting the wireless cards to nstreme mode, creating nstreme dual interfaces, setting frequencies and radios, and specifying the remote MAC addresses. The MAC addresses are set on each device to allow the nstreme dual interfaces to communicate over the wireless bridge.

Uploaded by

nuro123
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Nstreme dual Step-by-Step

Nstreme dual Step-by-Step


Here is a step-by-step explanation how to enable nstreme dual on a fresh installed MikroTik devices: I. MikroTik Device 1 1.1. Enabling wireless cards 1 and 2: [admin@MikroTik] > interface enable wlan1 [admin@MikroTik] > interface enable wlan2 1.2. Assigning IP address to the ethernet interface: [admin@MikroTik] > ip address add address=192.168.1.1/24 interface=ether1 1.3. Creating bridge interface: [admin@MikroTik] > interface bridge add 1.4. Adding ethernet interface to the bridge interface: [admin@MikroTik] > interface bridge port add interface=ether1 bridge=bridge1 1.5. Setting wireless cards 1 and 2 to nstreme mode: [admin@MikroTik] > interface wireless set wlan1 mode=nstreme-dual-slave [admin@MikroTik] > interface wireless set wlan2 mode=nstreme-dual-slave 1.6. Creating nstreme dual interface and setting Tx and Rx radios and frequencies:
[admin@MikroTik] > interface wireless nstreme-dual add rx-radio=wlan1 tx-radio=wlan2 rx-band=5ghz tx-band=5ghz rx-frequency=5180 tx-frequency=5300

1.7. Adding nstreme interface to the bridge: [admin@MikroTik] > interface bridge port add interface=nstreme1 bridge=bridge1 1.8. Checking the MAC address of the nstreme interface (in this example: 11:11:11:11:11:11):
[admin@MikroTik] > interface wireless nstremedual print Flags: X 0 X disabled, R running name="nstreme1" mtu=1500 macaddress=11:11:11:11:11:11 arp=enabled

disablerunningcheck=no tx-radio=wlan2 rx-radio=wlan1 remotemac=00:00:00:00:00:00 tx-band=5ghz tx-frequency=5300 rx-band=5ghz rx-frequency=5180 ratesb=1Mbps,2Mbps,5.5Mbps,11Mbps ratesa/g=6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps,54Mbps framerpolicy=none framerlimit=2560

II. MikroTik Device 2 2.1. Enabling wireless cards 1 and 2: [admin@MikroTik] > interface enable wlan1 [admin@MikroTik] > interface enable wlan2 2.2. Assigning IP address to the ethernet interface: [admin@MikroTik] > ip address add address=192.168.1.2/24 interface=ether1

Nstreme dual Step-by-Step 2.3. Creating bridge interface: [admin@MikroTik] > interface bridge add 2.4. Adding ethernet interface to the bridge interface: [admin@MikroTik] > interface bridge port add interface=ether1 bridge=bridge1 2.5. Setting wireless cards 1 and 2 to nstreme mode: [admin@MikroTik] > interface wireless set wlan1 mode=nstreme-dual-slave [admin@MikroTik] > interface wireless set wlan2 mode=nstreme-dual-slave 2.6. Creating Nstreme dual interface and setting Tx and Rx radios and frequencies and setting the MAC address of the remote nstreme interface (in this example: 11:11:11:11:11:11 [step 1.8]):
[admin@MikroTik] > interface wireless nstreme-dual add rx-radio=wlan1 tx-radio=wlan2 rx-band=5ghz tx-band=5ghz rx-frequency=5300 tx-frequency=5180 remotemac=11:11:11:11:11:11 disabled=no

2.7. Adding nstreme interface to the bridge: [admin@MikroTik] > interface bridge port add interface=nstreme1 bridge=bridge1 2.8. Checking the MAC address of the nstreme interface (in this example: 22:22:22:22:22:22):
[admin@MikroTik] > interface wireless nstremedual print Flags: X 0 disabled, R running rx-radio=wlan1 remotemac=11:11:11:11:11:11 R name="nstreme1" mtu=1500 macaddress=22:22:22:22:22:22 arp=enabled

disablerunningcheck=no tx-radio=wlan2 ratesb=1Mbps,2Mbps,5.5Mbps,11Mbps

tx-band=5ghz tx-frequency=5180 rx-band=5ghz rx-frequency=5300 ratesa/g=6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps,54Mbps framerpolicy=none framerlimit=2560

III. MikroTik Device 1 1.9. Setting the MAC address of the remote nstreme interface (in this example: 22:22:22:22:22:22 [step 2.8]): [admin@MikroTik] > interface wireless nstreme-dual set nstreme1 remotemac=22:22:22:22:22:22 disabled=no

Article Sources and Contributors

Article Sources and Contributors


Nstreme dual Step-by-Step Source: http://wiki.mikrotik.com/index.php?oldid=6875 Contributors: Bney, Dimitarv

You might also like