En 1418-1998

Download as pdf or txt
Download as pdf or txt
You are on page 1of 12
At a glance
Powered by AI
The document discusses standards and approval testing for welding personnel.

It discusses the British Standard for approval testing of welding operators and resistance weld setters.

Technical Committee WEE/36, Approval testing of welding procedures and welders is responsible for the document.

BRITISH STANDARD

Welding personnel Approval testing of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials

The European Standard EN 1418:1997 has the status of a British Standard

ICS 25.160.10

NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW

| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

BS EN 1418:1998

BS EN 1418:1998

National foreword
This British Standard is the English language version of EN 1418:1997 published by the European Committee for Standardization (CEN). The UK participation in its preparation was entrusted to Technical Committee WEE/36, Approval testing of welding procedures and welders, which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled International Standards Correspondence Index, or by using the Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations.

Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 9, and a back cover.
This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 April 1998 BSI 1998

Amendments issued since publication Amd. No. Date Text affected

ISBN 0 580 29019 0

EUROPEAN STANDARD ENNE NORME EUROPE ISCHE NORM EUROPA

EN 1418
December 1997

ICS 25.160.10 Descriptors: Welding, lasers, arc welding, electron beam welding, submerged arc welding, gas shielded welding, pressure welding, welded joints, metals, qualification, certification, welders (personnel), acceptability, tests, testing conditions

English version

Welding personnel Approval testing of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials
Personnel en soudage Epreuve de qualification des ope rateurs soudeurs pour le soudage par fusion et des re gleurs en soudage par re sistance pour le soudage totalement me canise et automatique des mate riaux me talliques Schweipersonal Pru fung von Bedienern von Schweieinrichtungen zum Schmelzschweien und von Einrichtern fu r das Widerstandsschweien fu r vollmechanisches und automatisches Schweien von metallischen Werkstoffen

This European Standard was approved by CEN on 3 November 1997. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.

CEN
European Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1418:1997 E

Page 2 EN 1418:1997

Foreword
This European Standard has been prepared by Technical Committee CEN/TC 121, Welding, of which the secretariat is held by DS. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 1998, and conflicting national standards shall be withdrawn at the latest by June 1998. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.

Contents
Foreword Introduction 1 Scope 2 Normative references 3 Definitions 3.1 automatic welding 3.2 function test 3.3 fully mechanized welding 3.4 pre-production welding test 3.5 production test 3.6 production sample testing 3.7 programming 3.8 robotic welding 3.9 setting-up 3.10 welding operator 3.11 resistance weld setter 3.12 welding unit 3.13 welding unit operation 3.14 examiner or examining body 4 Approval 4.1 General 4.2 Essential variables and ranges of approval 4.3 Period of validity 5 Prolongation 6 Certificate 7 Documentation Annex A (informative) Knowledge on welding technology Annex B (normative) Functional knowledge appropriate to the welding unit Annex C (informative) Approval test certificate for welding operators/resistance weld setters Page 2 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 5 5 6 6 7 8

BSI 1998

Page 3 EN 1418:1997

Introduction
This standard is intended to provide a basis for mutual recognition by examining bodies for approval related to the competence of welding operators and resistance weld setters in the various fields of application. Tests shall be carried out in accordance with this standard, unless more severe tests are specified by the relevant application standards, when these shall be applied. In order to make this standard applicable for fusion and resistance welding, the terminology, especially for welding operator in the field of fusion welding, and resistance weld setter in the field of resistance welding, was clarified. The welding operator/resistance weld setter's ability and job knowledge continue to be approved only if the welding operator/resistance weld setter is working with reasonable continuity on welding work within the extent of approval. All new approvals are to be in accordance with this standard from the date of issue. However, this standard does not invalidate previous approvals made to former national standards or specifications, providing the intent of the technical requirements is satisfied and the previous approvals are relevant to the application and production work on which they are to be employed. Also, where additional tests have to be carried out to make the approval technically equivalent it is only necessary to do the additional tests that should be made in accordance with this standard. Considerations of previous approvals to former national standards or specifications should be made at the time of the enquiry or contract stage and agreed between the contracting parties.

2 Normative references
This standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendements to or revisions of any of these publications apply to this standard only when incorporated in it by amendement or revision. For undated references the latest edition of the publication referred to applies. EN 288-2, Specification and approval of welding procedures for metallic materials Part 2: Welding procedure specification for arc welding EN 288-3, Specification and approval of welding procedures for metallic materials Part 3: Welding procedure tests for the arc welding of steels EN 288-4, Specification and approval of welding procedures for metallic materials Part 4: Welding procedure tests for the arc welding of aluminium and its alloys EN 288-8, Specification and approval of welding procedures for metallic materials Part 8: Approval by a pre-production welding test EN 719, Welding coordination Tasks and responsibilities EN ISO 9956-10, Specification and approval of welding procedures for metallic materials Part 10: Welding procedure specification for electron beam welding (ISO 9956-10:1996) EN ISO 9956-11, Specification and approval of welding procedures for metallic materials Part 11: Welding procedure specification for laser beam welding (ISO 9956-11:1996) ISO/DIS 857:1995, Welding and allied processes Welding, brazing and soldering processes Vocabulary ISO 10447, Welding Peel and chisel testing of resistance spot, projection and seam welds

1 Scope
This standard specifies requirements for approval of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding processes of metallic materials. Only welding operators/resistance weld setters responsible for setting up and/or adjustment during welding have to be approved. Personnel exclusively performing the programming of the welding unit or operation of the welding unit do not need any particular approval. This standard is applicable when approval testing of operators/resistance weld setters is required by the contract or by the application standard. This standard does not apply to welding operators in resistance welding (see 3.10) or under hyperbaric conditions.

3 Definitions
For the purposes of this standard, the classification of manual welding and partly mechanized welding according to table 1 of ISO/DIS 857:1995 and the following definitions apply. 3.1 automatic welding welding where all operations are performed automatically. Manual adjustment of welding variables during welding is not possible 3.2 function test test of a welding unit set-up in accordance with a welding procedure specification (WPS)

BSI 1998

Page 4 EN 1418:1997

3.3 fully mechanized welding welding where all main operations (excluding handling of the work piece) are performed automatically. Manual adjustment of welding variables during welding is possible 3.4 pre-production welding test a welding test having the same function as a welding procedure test, but based on a non-standard test piece, simulating production conditions 3.5 production test welding test carried out in the production environment on the welding unit, on actual products or on simplified test pieces. The main characteristic of a production test is that normal production is interrupted during this test 3.6 production sample testing sample testing of actual welding products sampled from a continuous production using the welding unit. No interruption of normal production during sampling is necessary 3.7 programming incorporation of the approved welding procedure specification and/or the specified movements of the welding unit into a programme 3.8 robotic welding automatic welding using a manipulator that can be pre-programmed to different welding directions and fabrication geometries 3.9 setting-up correct adjustment of the welding unit before welding and if required by entering the robot programme 3.10 welding operator in fusion welding a person who performs fully mechanized or automatic welding. In resistance welding the welding operator uses equipment with mechanized or fully mechanized relative movement between the welding gun and the workpiece and is only given task orientated training (see also clause 1) 3.11 resistance weld setter person who sets up mechanized or automatic welding

3.12 welding unit totality of equipment which performs the welding. The welding unit can include jigs and fixtures, one or more robots, feeding units and other ancillary equipment. The equipment can perform loading and unloading of the work pieces 3.13 welding unit operation starting and if necessary stopping the production cycle. The operation can include loading and unloading of the work pieces 3.14 examiner or examining body a person or organization who verifies compliance with the application standard. The examiner/examing body shall be acceptable to any contracting parties

4 Approval
4.1 General Welding operators/resistance weld setters shall be approved by one of the following methods, as detailed in 4.2: approval based on welding procedure test, see 4.2.1; approval based on pre-production welding test or production test, see 4.2.2; approval based on production sample testing, see 4.2.3; approval based on function test, see 4.2.4. Any of the approval methods can be supplemented by a test of knowledge related to welding technology. Such a test is recommended, but not mandatory. Annex A includes a recommandation for such an examination. The methods shall be supplemented by a test of the functional knowledge appropriate to the welding unit (see annex B). The essential variables and the range of approval is specified in the appropriate subclauses of 4.2 and the validity in 4.3. 4.2 Essential variables and ranges of approval 4.2.1 Approval based on welding procedure testing A welding operator/resistance weld setter having successfully completed a welding procedure test in accordance with the relevant Part 3 or Part 4 of EN 288, shall be considered approved for that type of welding unit used. Provided that the welding operator/resistance weld setter works according to an approved welding procedure specification (WPS), there is no limitation for the range of approval, provided that the type of welding unit and the welding process are not changed. A suggested form for the certificate is shown in annex C.
BSI 1998

Page 5 EN 1418:1997

4.2.2 Approval based on pre-production welding test or production test A welding operator/resistance weld setter having successfully completed a pre-production welding test in accordance with EN 288-8 or production test shall be considered approved for that type of welding unit used. Provided that the welding operator/resistance weld setter works according to an approved welding procedure specification (WPS), there is no limitation for the range of approval, provided that the type of welding unit and the welding process are not changed. A suggested form for the certificate is shown in annex C. 4.2.3 Approval based on production sampling testing A welding operator/resistance weld setter having successfully set up the production shall be considered approved if representative samples of the items produced are approved. This testing of production samples is to be in accordance with the requirements of the contracting parties. Provided that the welding operator/resistance weld setter works according to an approved welding procedure specification (WPS), there is no limitation for the range of approval, provided that the type of welding unit and the welding process are not changed. A suggested form for the certificate is shown in annex C. 4.2.4 Approval based on function test A welding operator/resistance weld setter having successfully performed a function test shall be considered approved for that type of welding unit. A function test shall include the following: to know the correlation between parameter deviations and the welding results; to control parameter setting at the welding unit according to WPS; to test the operational items of the welding unit according to WPS; to report of any malfunction of the welding unit which influenced the weld. Provided the welding operator/resistance weld setter works according to an approved welding procedure specification (WPS), there is no limitation for the range of approval, provided that the type of welding unit and the welding process are not changed. A suggested form for the certificate is shown in annex C.

4.2.5 Automatic and robotic welding The following changes require a new approval: welding with or without arc and/or joint sensor; change from single-run to multi-run technique; change of robotic type and system including numerical control unit; other essential variables specific to the processes used. Welding without joint sensor also covers welding with joint sensor, but not vice versa. Welding with multi-run technique also covers single-run technique, but not vice versa. 4.3 Period of validity The validity of the welding operator/resistance weld setter's approval starts from the date of welding of the test piece, provided that the required tests are satisfactory. A welding operator/resistance weld setter's approval shall remain valid for a period of two years provided that the employer/welding coordinator in accordance with EN 719 confirms that both the following conditions are fulfilled: a) The welding operator/resistance weld setter shall be engaged with reasonable continuity on welding work within the current range of approval. An interruption for a period no longer than six months is permitted. b) There shall be no specific reason to question the welding operator/resistance weld setter's knowledge. If any of these conditions are not fulfilled, the approval shall be cancelled. The employer/welding coordinator may sign the relevant certificate at six month intervals in respect of the foregoing.

5 Prolongation
The validity of the approval on the certificate may be prolonged for further periods of two years, within the original range of approval, provided each of the following conditions according to 4.3 are fulfilled: the production welds are of the required quality; records of tests, e.g. half-yearly documentation about radiographic or ultrasonic inspections or test reports about fracture test or peel and chisel test in accordance with ISO 10447 shall be maintained on file with the operator/resistance weld setter's approval certificate. The examiner or examing body shall verify compliance with the above conditions and sign the prolongation of the welding operator/resistance weld setter's approval test certificate.

BSI 1998

Page 6 EN 1418:1997

6 Certificate
The examiner or examining body shall certify that the welding operator/resistance weld setter has successfully passed the approval test. All relevant test conditions shall be recorded on the certificate. If the welding operator/resistance weld setter fails any of the prescribed tests, no certificate shall be issued. The certificate shall be issued under the sole responsibility of the examiner or examing body and shall contain all the information detailed in annex C. The format of annex C is recommended to be used as the welding operator/resistance weld setter's approval test certificate. If any other form of welding operator/resistance weld setter's approval test certificate is used, it shall contain the information required in annex C. The manufacturer's WPS as shown in EN 288-2, EN ISO 9956-10 or EN ISO 9956-11 shall give information about materials, welding positions, welding processes and range of welding parameters, etc., in accordance with this standard. The welding operator/resistance weld setter's approval test certificate shall be issued at least in one of the following languages: English; French; German. Each change of the essential variables for the approval testing beyond the permitted ranges requires a new test and a new approval certificate.

7 Documentation
Certificates and test reports/records of welding tests and prolongations shall be kept on file.

BSI 1998

Page 7 EN 1418:1997

Annex A (informative) Knowledge on welding technology


A.1 General The test of job knowledge is recommended, but it is not mandatory. However, some countries can require that the welding operator/resistance weld setter undergoes a test of job knowledge. If the job knowledge test is carried out, it should be recorded on the welding operator/resistance weld setter's certificate. This annex outlines the job knowledge that a welding operator/resistance weld setter should have to ensure that procedures are followed and common practices are complied with. The job knowledge indicated in this annex is only pitched at the most basic level. Owing to different training programmes in various countries, it is only proposed to standardize general objectives or categories of job knowledge. The actual questions used should be drawn up by the individual country, but should include questions on areas covered in A.2, relevant to the welding operator/resistance weld setter's approval test. The actual tests of a welding operator/resistance weld setter's job knowledge can be given by any of the following methods or combinations of these methods: a) written objective tests (multiple choice); b) oral questioning following a set of written questions; c) computer testing; d) demonstration/observation testing following a written set of criteria. The test of job knowledge is limited to the matters related to the welding process used in the test. A.2 Requirements A.2.1 Welding equipment A.2.1.1 Arc welding a) Identification of gas cylinders. b) Identification and assembly of essential components. c) Selection of correct nozzles and welding torches. d) Wire feed control method. A.2.1.2 Beam welding a) Electron beam welding equipment. b) Laser beam welding equipment. A.2.1.3 Pressure welding a) Types and equipment. b) Identification and assembly of essential components.

A.2.1.4 Resistance welding a) Identification and assembly of essential components. b) Selection of correct electrodes. c) Cooling system. d) Maintenance of the equipment. A.2.2 Welding processes1) A.2.2.1 Shielded metal-arc welding (114, 131, 135, 136, 137, 141, 15) a) Procedures. b) Types and size of electrodes. c) Identification of shielding gas and flow rate (without 114). d) Type, size and maintenance of nozzles/contact tip. e) Selection and limitation of mode of metal transfer. f) Protection of the welding arc from draughts. A.2.2.2 Submerged arc welding (121, 122) a) Procedures. b) Drying, feeding and correct recovery of flux. c) Correct alignment and travel of welding head. d) Single-wire or multi-wire process. e) Influence of welding current and voltage. A.2.2.3 Electron beam welding (76) a) Procedures. b) Parameters and their influence to the welding process. c) Focusing system. d) Parameter controlling. e) Preparation of parent material. f) Vacuum system including leak test. A.2.2.4 Laser beam welding (751) a) Procedures. b) Parameters and their influence to the welding process. c) Focusing system. d) Parameter controlling. e) Preparation of parent material. f) Choice of relevant gases. g) Processing in/on different types of laser. h) Type of mode for operation. A.2.2.5 Pressure welding (41, 42, 44, 45) a) Procedures. b) Type of equipment. c) Surface preparation. d) Control system.

1)

The numbers refer to EN 24063.

BSI 1998

Page 8 EN 1418:1997

A.2.2.6 Resistance welding (21, 22, 23, 24, 25, 29) a) Procedures. b) Surface preparation. c) Parameters. d) Material and shape of electrodes, contact area and fixing of electrodes. e) Method of welding. f) Control and surveillance system. g) Causes of defect. h) Test methods. A.2.3 Parent metals a) Identification of material. b) Methods and control of pre-heating. c) Control of interpass temperature. A.2.4 Consumables a) Identification of consumables. b) Storage, handling and conditioning of consumables. c) Selection of correct size. d) Cleanliness of wire electrodes and flux-cored electrodes. e) Control of wire spooling. f) Control and monitoring of gas flow rates and quality. g) Principles of welding without consumables. A.2.5 Safety and accident prevention A.2.5.1 General a) Electrical risk. b) Mechanical risk. c) Risk of welding fumes and gases. d) Noise risk. e) Risk by radiographic application (if relevant). A.2.5.2 All arc processes a) Environment with increased hazard of electric shock. b) Radiation from the arc. c) Effects of stray arcing. d) Effects of poor earthing. A.2.6 Visual examination of welds a) Knowledge of visual examination.

Annex B (normative) Functional knowledge appropriate to the welding unit


This annex outlines the functional knowledge appropriate to the welding unit that a welding operator/resistance weld setter should have to ensure that procedures are followed and common practices are complied with. B.1 Welding sequences/procedures in the relevant process Appreciation of welding procedure requirements and the influence of welding parameters. B.2 Joint preparation and weld representation in the relevant process a) Conformance of joint preparation to welding procedure specification (WPS). b) Cleanliness of fusion faces. B.3 Weld imperfection in the relevant process a) Identification of weld imperfection. b) Causes. c) Prevention and remedial action. B.4 Welding operator/resistance weld setter's approval The welding operator/resistance weld setter shall be aware of the range of the approval. B.5 Process operation a) Knowledge of programming (if relevant). b) Knowledge of the control system and signals given by this system. c) Moving system. d) Auxiliary equipment. e) Jigs and fixtures and set-up. f) Parameters and adjustment within the given procedures. g) Safety regulations and precautions. h) Start-stop procedures.

BSI 1998

Page 9 EN 1418:1997

Annex C (informative) Approval test certificate for welding operators/resistance weld setters
Manufacturer's welding procedure specification Reference no. (if applicable): Name of welding operator/resistance weld setter: Identification: Method of identification: Date and place of birth: Employer: Code/testing standard: Job knowledge: acceptable/not tested (delete as necessary) Weld details Welding process Welding unit Details in accordance with 4.2.5 Joint sensor Single run/multirun technique Robotic type Range of approval Examiner or examining body Reference no.

Photograph (if required)

Additional information is available on attached sheet and/or welding procedure specification No.: The approval is based on: Welding procedure test in accordance with 4.2.1 Pre-production welding test or production test in accordance with 4.2.2 Production sampling testing in accordance with 4.2.3 Function test in accordance with 4.2.4 Results of the approval test see document no. (welding procedure approval record or other documents of testing) Prolongation for approval by examiner or examining body for the following 2 years (see clause 5) Date Signature Position or title Name, date and signature Examiner or examining body Date of issue Location Validity of approval until Prolongation for approval by employer/welding coordinator for the following 6 months (see clause 5)

Date

Signature

Position or title

BSI 1998

BSI 389 Chiswick High Road London W4 4AL

| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

BSI British Standards Institution


BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.

You might also like