GALV - Cut Edge Protection

10.
CUT EDGE PROTECTION

INTRODUCTION One of the most important characteristics of zinc (galvanized) coatings on steel is the ability of the zinc to protect adjacent steel from corrosion. The electrical potential between zinc and steel ensures that zinc will act as an anode to adjacent exposed steel and prevent its corrosion. All continuously galvanized products are dependent on the cathodic protection of their galvanized coatings to protect them from localised corrosion, as the galvanized coatings on all of these products are damaged during the manufacturing process. They are cut, formed or punched after being manufactured from sheet, wire, or hollow and open sections to feed the next stage of the manufacturing process. The degree of protection provided by the zinc coating to the exposed cut edges will be determined by: 1. 2. 3. The thickness of the material. The mass of zinc available in the coating adjacent to the exposed steel. The nature of the environment to which the product is exposed.
The cut edge corrosion phenomenon is almost always ignored in Standards and specications. Australian Standard AS/NZS 4680:2006 Hot dip galvanized coatings on fabricated ferrous items, is a good example of this. The requirement to repair damaged areas on items galvanized after fabrication is clearly dened in the Standard, where the maximum permissible uncoated areas are nominated in terms of area. In other standards associated with continuously galvanized products, there is no such requirement for repair of cut edges on sheet, tube, or wire products that are galvanized prior to fabrication. This is particularly relevant with cold-formed structural sections (purlins, channels) used for commercial construction, where the exposed steel per unit of surface exceeds the maximum allowable repairable area in the hot dip galvanizing standard.
HOW FAR DOES GALVANIC PROTECTION EXTEND? For many years, the only type of product reliant on galvanic protection of its cut edges was hot dip galvanized sheet used for roong and cladding. The base steel used for these applications is very thin, typically 0.5-0.7 mm in thickness and thus the surface area of bare steel exposed is negligible. Development in continuous manufacturing and coating of pipe and open structural sections, as well as heavier (up to 3.2 mm) sheet has resulted in a wide range of products being developed that have signicant areas of exposed steel between the coated surfaces.
Pre-galvanized products rely on cathodic protection to prevent corrosion on their cut edges. Thicker sections such as these heavy purlins are on the borderline and corrosion is visible on installation.
The other factor common to all galvanized products is the coatings ability to protect any exposed steel in the event of damage to the coated surface. While the ability of galvanized coatings to cathodically protect adjacent exposed steel has been evaluated empirically for over 100 years, few attempts have been made to quantify this phenomenon. Work done in by X.G.(Gregory) Zhang of the Cominco Product Technology Centre, Mississauga, Canada, has allowed a more scientic approach to be taken. 41
10. CUT EDGE PROTECTION
EXPERIMENTAL RESULTS The Cominco research by Gregory Zhang was aimed at determining the consumption rate of zinc as a barrier coating along with its galvanic protection of the exposed steel. Samples were prepared to simulate various zinc/steel combinations and included a number of degrees of separation, using zinc and steel strips of various thicknesses embedded in epoxy resin mounts. The samples were subjected to testing in the following environments: ASTM standard salt spray test full immersion test cyclic wet-dry humidity tests actual atmosphere exposure test.
After testing in each corrosion environment, the samples were evaluated with an optical microscope. Each sample was inspected for areas of rusted and non-rusted steel surface based on both colour and depth of corrosion. Brown to dark brown discoloration on the steel surfaces was used to dene the range of galvanic protection provided by the zinc. CONCLUSION In atmospheric exposure conditions, the Cominco report concludes that cathodic protection afforded to exposed steel by a zinc (galvanized) coating will be about 2 mm. This will vary somewhat depending on exposure conditions, and while rusting may occur outside this area, partial galvanic protection Very thin (<0.5 mm) sections used for roong will cover a much larger area and signicantly moderate the rate and cladding are well protected on their cut edges because of the proximity of the zincof steel corrosion in this area. The thin (0.2 mm) lateral surface based coating on each face of the sheeting. of the zinc coating will be subject to galvanic corrosion in protecting the adjacent exposed steel while the rest of the zinc coating will corrode normally.
42
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46
SPECIFIERS MANUAL INDUSTRIAL GALVANIZERS COMPANY PROFILE ADHESION OF PROTECTIVE COATINGS BOLTING GALVANIZED STEEL BURIED GALVANIZED STEEL CONCRETE DURABILITY & GALVANIZED REBAR CORROSION MAPPING COST FACTORS FOR HOT DIP GALVANIZED COATINGS CUSTOM COATING PACKAGES CUT EDGE PROTECTION DESIGNING FOR GALVANIZING ILLUSTRATED GUIDE TO DESIGN FOR GALVANIZING DEW POINT TABLES DIFFICULT STEELS FOR GALVANIZING DOCUMENTATION - CORRECT PAPERWORK ENSUES EFFICIENT PROCESSING ENVIRONMENTAL ISSUES FOR INDUSTRIAL COATINGS ZINC, HUMAN HEALTH AND THE ENVIRONMENT DEFECTS IN GALVANIZED COATINGS GALVANIC SERIES GLOSSARY OF GALVANIZING TERMS GUARANTEES FOR HOT DIP GALVANIZED COATINGS LIFE CYCLE COSTS OF INDUSTRIAL PROTECTIVE COATING SYSTEMS PAINTING OVER GALVANIZED COATINGS POWDER COATING OVER GALVANIZED COATINGS QUALITY AND SERVICE FACTORS AFFECTING GALVANIZED COATINGS RESTORATION OF PREVIOUSLY GALVANIZED ITEMS REPAIR OF GALVANIZED COATINGS STEEL STRENGTH AND HOT DIP GALVANIZING STANDARDS - AS/NZS 4680:2006 STANDARDS - AUSTRALIAN AND INTERNATIONAL STANDARDS STEEL SURFACE PREPERATION SURFACE PREPERATION FOR PAINTING HOT DIP GALVANIZED COATINGS THICKNESS MEASUREMENT OF PROTECTIVE COATINGS WELDING GALVANIZED STEEL AN INTRODUCTION TO THE HOT DIP GALVANIZING PROCESS ZINC COATING PROCESSES - OTHER METHODS GALVANIZED COATINGS AND BUSHFIRE LIQUID METAL ASSISTED CRACKING OF GALVANIZED STRUCTURAL STEEL SECTIONS GALVANIZING 500N GRADE REINFORCING BAR PREDICTING THE LIFE OF GALVANIZED COATINGS CHEMICALS IN CONTACT WITH GALVANIZED COATINGS. ATMOSPHERIC CORROSIVITY ASSESSMENT GLOBAL WARMING - CLIMATE CHANGE AND GALVANIZING STEEL - ITS CORROSION CHARACTERISTICS GALVANIZED STEEL AND TIMBER WHITE RUST PREVENTION AND TREATMENT
01 - SPECIFIERS MANUAL THIRD EDITION

Industrial Galvanizers Australian Galvanizing Division (IGAG) operates nine galvanizing plants around Australia, ranging in size from large structural galvanizing facilities to specialised small plants designed to process small parts. The Australian Galvanizing Division has galvanized in excess of 2 million tonnes of steel products in Australia since its rst plant was commissioned in 1965 and is recognized for its ability to handle complex and difcult projects, as well as routine contracts. This experience has been collated in the Speciers Design Manual, to assist those involved in the design of steel products and projects to better understanding the galvanizing process and allow the most durable and cost-effective solutions to be delivered to these products and projects. All sections of this Third Edition have been completely updated and additional sections have been included to provide additional technical information related to the use of hot dip galvanized steel. In addition to its Australian Galvanizing operations, Industrial Galvanizers Corporation has a network of manufacturing operations in Australia, as well as galvanizing and manufacturing businesses throughout Asia and in the USA. The companys staff in all these locations will be pleased to assist with advice on design and performance of hot dip galvanized coatings and products. Contact details for each of these locations are located elsewhere in this manual. This edition of the Industrial Galvanizers Speciers Manual has been produced in both html and .pdf formats for ease of access and distribution and all documents in the Manual are in .pdf format and can be printed if paper documents are required. The Speciers Manual is also accessible in its entirety on the companys web site at www.ingal.com.au. Additional copies of the Speciers Manual are available on CD on request. PUBLISHER: Industrial Galvanizers Australian Galvanizing Division, PO Box 503, MOOROOKA QLD 4105 Ph: 07 38597418 EDITOR: John Robinson, Mount Townsend Solutions Pty Ltd PO Box 355, JESMOND NSW 2299 Ph: 0411 886 884 Email: [email protected] LAYOUT AND DESIGN: Adrian Edmunds, Nodding Dog Design Ph: 0402 260 734 Email: [email protected] Web: www.noddingdogdesign.com

GALV - Cut Edge Protection

Uploaded by

Copyright:

Available Formats

GALV - Cut Edge Protection

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

GALV - Cut Edge Protection

Uploaded by

Copyright:

Available Formats

What is the Cominco research trying to determine?

How does the thickness of the material affect cut edge protection?

10.

CUT EDGE PROTECTION

10. CUT EDGE PROTECTION

01 - SPECIFIERS MANUAL THIRD EDITION

You might also like