At - Automatic Transaxel

AUTOMATIC TRANSAXLE SECTION
GI MA EM LC EC
AT
CONTENTS
TROUBLE DIAGNOSIS - INDEX ....................................4 Alphabetical & P No. Index for DTC ...........................4 PRECAUTIONS ...............................................................6 Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TENSIONER ...............6 Precautions for On Board Diagnostic (OBD) System of A/T and Engine...........................................6 Precautions ..................................................................6 Service Notice or Precautions .....................................8 Wiring Diagrams and Trouble Diagnosis.....................9 PREPARATION .............................................................10 Special Service Tools ................................................10 Commercial Service Tools .........................................12 OVERALL SYSTEM ......................................................14 A/T Electrical Parts Location .....................................14 Circuit Diagram ..........................................................15 Cross-sectional View - RE4F03B ..............................16 Cross-sectional View - RE4F03W .............................17 Hydraulic Control Circuit............................................18 Shift Mechanism ........................................................19 Control System ..........................................................28 Control Mechanism....................................................29 Control Valve .............................................................34 ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION ...............................................................36 Introduction ................................................................36 OBD-II Function for A/T System................................36 One or Two Trip Detection Logic of OBD-II ..............36 OBD-II Diagnostic Trouble Code (DTC) ....................36 Malfunction Indicator Lamp (MIL)..............................40 CONSULT-II ...............................................................40 TROUBLE DIAGNOSIS - INTRODUCTION ..................56 Introduction ................................................................56 Work Flow..................................................................60 TROUBLE DIAGNOSIS - BASIC INSPECTION ...........62 A/T Fluid Check .........................................................62 Stall Test ....................................................................62 Line Pressure Test.....................................................66 Road Test...................................................................67 TROUBLE DIAGNOSIS - GENERAL DESCRIPTION ...............................................................86 Symptom Chart..........................................................86 TCM Terminals and Reference Value........................99 TROUBLE DIAGNOSIS FOR POWER SUPPLY ........104 Wiring Diagram - AT - MAIN....................................104 Diagnostic Procedure ..............................................105 DTC P0705 PARK/NEUTRAL POSITION (PNP) SWITCH .......................................................................107 Description ...............................................................107 Wiring Diagram - AT - PNP/SW...............................109 Diagnostic Procedure ..............................................110 Component Inspection.............................................112 DTC P0710 A/T FLUID TEMPERATURE SENSOR CIRCUIT .......................................................................113 Description ...............................................................113 Wiring Diagram - AT - FTS ......................................115 Diagnostic Procedure ..............................................116 Component Inspection.............................................118 DTC P0720 VEHICLE SPEED SENSOR.A/T (REVOLUTION SENSOR) ...........................................119 Description ...............................................................119 Wiring Diagram - AT - VSSA/T ................................121 Diagnostic Procedure ..............................................122 DTC P0725 ENGINE SPEED SIGNAL .......................124 Description ...............................................................124 Wiring Diagram - AT - ENGSS ................................125 Diagnostic Procedure ..............................................126 DTC P0731 A/T 1ST GEAR FUNCTION ....................128 Description ...............................................................128 Wiring Diagram - AT - 1ST ......................................131 Diagnostic Procedure ..............................................132 Component Inspection.............................................133 DTC P0732 A/T 2ND GEAR FUNCTION ....................135 Description ...............................................................135 Wiring Diagram - AT - 2ND......................................138 Diagnostic Procedure ..............................................139 Component Inspection.............................................140 DTC P0733 A/T 3RD GEAR FUNCTION ....................141
FE CL MT
AX SU BR ST RS BT HA SC EL IDX
CONTENTS
Description ...............................................................141 Wiring Diagram - AT - 3RD......................................144 Diagnostic Procedure ..............................................145 Component Inspection.............................................146 DTC P0734 A/T 4TH GEAR FUNCTION ....................147 Description ...............................................................147 Wiring Diagram - AT - 4TH ......................................151 Diagnostic Procedure ..............................................152 Component Inspection.............................................156 DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE ......................................................157 Description ...............................................................157 Wiring Diagram - AT - TCV......................................159 Diagnostic Procedure ..............................................160 Component Inspection.............................................162 DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP) ....163 Description ...............................................................163 Wiring Diagram - AT - TCCSIG ...............................166 Diagnostic Procedure ..............................................167 Component Inspection.............................................173 DTC P0745 LINE PRESSURE SOLENOID VALVE ...174 Description ...............................................................174 Wiring Diagram - AT - LPSV....................................176 Diagnostic Procedure ..............................................177 Component Inspection.............................................180 DTC P0750 SHIFT SOLENOID VALVE A ..................181 Description ...............................................................181 Wiring Diagram - AT - SSV/A ..................................183 Diagnostic Procedure ..............................................184 Component Inspection.............................................186 DTC P0755 SHIFT SOLENOID VALVE B ..................187 Description ...............................................................187 Wiring Diagram - AT - SSV/B ..................................189 Diagnostic Procedure ..............................................190 Component Inspection.............................................192 DTC P1705 THROTTLE POSITION SENSOR ...........193 Description ...............................................................193 Wiring Diagram - AT - TPS......................................196 Diagnostic Procedure ..............................................197 Component Inspection.............................................201 DTC P1760 OVERRUN CLUTCH SOLENOID VALVE ..........................................................................202 Description ...............................................................202 Wiring Diagram - AT - OVRCSV..............................204 Diagnostic Procedure ..............................................205 Component Inspection.............................................207 DTC BATT/FLUID TEMP SEN (A/T FLUID TEMP SENSOR CIRCUIT AND TCM POWER SOURCE) ....208 Description ...............................................................208 Wiring Diagram - AT - BA/FTS ................................210 Diagnostic Procedure ..............................................211 Component Inspection.............................................214
(Contd)
DTC VHCL SPEED SEN.MTR VEHICLE SPEED SENSOR.MTR ..............................................................215 Description ...............................................................215 Wiring Diagram - AT - VSSMTR..............................217 Diagnostic Procedure ..............................................218 DTC CONTROL UNIT (RAM), CONTROL UNIT (ROM) ...........................................................................219 Description ...............................................................219 Diagnostic Procedure ..............................................219 DTC CONTROL UNIT (EEP ROM) .............................221 Description ...............................................................221 Diagnostic Procedure ..............................................222 TROUBLE DIAGNOSES FOR SYMPTOMS ...............223 Wiring Diagram - AT - NONDTC .............................223 1. O/D OFF Indicator Lamp Does Not Come On....225 2. Engine Cannot Be Started In P and N Position ....................................................................228 3. In P Position, Vehicle Moves Forward Or Backward When Pushed .........................................229 4. In N Position, Vehicle Moves ...........................230 5. Large Shock. N -> R Position .......................232 6. Vehicle Does Not Creep Backward In R Position ....................................................................234 7. Vehicle Does Not Creep Forward In D, 2 Or 1 Position.........................................................237 8. Vehicle Cannot Be Started From D1 ...................240 9. A/T Does Not Shift: D1 -> D2 Or Does Not Kickdown: D4 -> D2..................................................243 10. A/T Does Not Shift: D2 -> D3.............................246 11. A/T Does Not Shift: D3 -> D4 .............................249 12. A/T Does Not Perform Lock-up .........................252 13. A/T Does Not Hold Lock-up Condition ..............254 14. Lock-up Is Not Released...................................256 15. Engine Speed Does Not Return To Idle (Light Braking D4 -> D3).....................................................257 16. Vehicle Does Not Start From D1 .......................259 17. A/T Does Not Shift: D4 -> D3, When Overdrive Control Switch ON -> OFF ...............260 18. A/T Does Not Shift: D3 -> 22, When Selector Lever D -> 2 Position.........................................261 19. A/T Does Not Shift: 22 -> 11, When Selector Lever 2 -> 1 Position .........................................262 20. Vehicle Does Not Decelerate By Engine Brake........................................................................263 21. TCM Self-diagnosis Does Not Activate (PNP, Overdrive Control and Throttle Position Switches Circuit Checks) ........................................................263 A/T SHIFT LOCK SYSTEM .........................................272 Description ...............................................................272 Shift Lock System Electrical Parts Location............272 Wiring Diagram - SHIFT -........................................273 Diagnostic Procedure ..............................................274
AT-2
CONTENTS
KEY INTERLOCK CABLE ..........................................278 Components.............................................................278 Removal...................................................................278 Installation................................................................279 ON-VEHICLE SERVICE ..............................................280 Control Valve Assembly and Accumulators.............280 Control Cable Adjustment........................................281 Park/Neutral Position (PNP) Switch Adjustment .....281 Differential Side Oil Seal Replacement ...................282 Revolution Sensor Replacement .............................282 REMOVAL AND INSTALLATION ...............................283 Removal...................................................................283 Installation................................................................284 OVERHAUL .................................................................286 Components.............................................................286 Oil Channel ..............................................................289 Locations of Adjusting Shims, Needle Bearings, Thrust Washers and Snap Rings ............................290 DISASSEMBLY............................................................291 REPAIR FOR COMPONENT PARTS .........................305 Manual Shaft............................................................305 Oil Pump ..................................................................308 Control Valve Assembly...........................................312 Control Valve Upper Body .......................................321 Control Valve Lower Body .......................................325 Reverse Clutch ........................................................327 High Clutch ..............................................................331 Forward Clutch and Overrun Clutch........................336 Low & Reverse Brake..............................................343 Rear Internal Gear, Forward Clutch Hub and Overrun Clutch Hub.................................................347 Output Shaft, Idler Gear, Reduction Pinion Gear and Bearing Retainer...............................................351 Band Servo Piston Assembly ..................................356
(Contd)
GI MA EM LC EC FE CL MT
Final Drive................................................................361 ASSEMBLY..................................................................368 Assembly (1)............................................................368 Adjustment (1) .........................................................369 Assembly (2)............................................................374 Adjustment (2) .........................................................378 Assembly (3)............................................................382 Assembly (4)............................................................384 SERVICE DATA AND SPECIFICATIONS (SDS) .......389 General Specifications.............................................389 Shift Schedule..........................................................389 Stall Revolution........................................................389 Line Pressure...........................................................389 Control Valves..........................................................390 Clutch and Brakes ...................................................390 Clutch and Brake Return Springs............................392 Oil Pump ..................................................................392 Input Shaft ...............................................................393 Planetary Carrier......................................................393 Final Drive................................................................393 Reduction Pinion Gear ............................................396 Output Shaft.............................................................398 Bearing Retainer......................................................398 Total End Play..........................................................399 Reverse Clutch End Play ........................................399 Accumulator .............................................................399 Band Servo ..............................................................399 Removal and Installation .........................................400 Shift Solenoid Valves...............................................400 Solenoid Valves .......................................................400 A/T Fluid Temperature Sensor.................................400 Revolution Sensor ...................................................400 Dropping Resistor ....................................................400
AT-3
TROUBLE DIAGNOSIS INDEX

Alphabetical & P No. Index for DTC
Alphabetical & P No. Index for DTC

ALPHABETICAL INDEX FOR DTC
DTC Items (CONSULT-II screen terms) A/T 1ST GR FNCTN A/T 2ND GR FNCTN A/T 3RD GR FNCTN A/T 4TH GR FNCTN A/T TCC S/V FNCTN ATF TEMP SEN/CIRC ENGINE SPEED SIG L/PRESS SOL/CIRC O/R CLTCH SOL/CIRC PNP SW/CIRC SFT SOL A/CIRC*2 SFT SOL B/CIRC*2 TCC SOLENOID/CIRC TP SEN/CIRC A/T*2 VEH SPD SEN/CIR AT*3 CONSULT-II GST*1 P0731 P0732 P0733 P0734 P0744 P0710 P0725 P0745 P1760 P0705 P0750 P0755 P0740 P1705 P0720 Reference page
NCAT0001 NCAT0001S01
AT-128 AT-135 AT-141 AT-147 AT-163 AT-113 AT-124 AT-174 AT-202 AT-107 AT-181 AT-187 AT-157 AT-193 AT-119
*1: These numbers are prescribed by SAE J2012. *2: When the fail-safe operation occurs, the MIL illuminates. *3: The MIL illuminates when both the Revolution sensor signal and the Vehicle speed sensor signal meet the fail-safe condition at the same time.
AT-4
TROUBLE DIAGNOSIS INDEX

Alphabetical & P No. Index for DTC (Contd)
P NO. INDEX FOR DTC

DTC CONSULT-II GST*1 P0705 P0710 P0720 P0725 P0731 P0732 P0733 P0734 P0740 P0744 P0745 P0750 P0755 P1705 P1760 PNP SW/CIRC ATF TEMP SEN/CIRC VEH SPD SEN/CIR AT*3 ENGINE SPEED SIG A/T 1ST GR FNCTN A/T 2ND GR FNCTN A/T 3RD GR FNCTN A/T 4TH GR FNCTN TCC SOLENOID/CIRC A/T TCC S/V FNCTN L/PRESS SOL/CIRC SFT SOL A/CIRC*2 SFT SOL B/CIRC*2 TP SEN/CIRC A/T*2 O/R CLTCH SOL/CIRC Items (CONSULT-II screen terms) Reference page
=NCAT0001S02
GI MA
AT-107 AT-113 AT-119 AT-124 AT-128 AT-135 AT-141 AT-147 AT-157 AT-163 AT-174 AT-181 AT-187 AT-193 AT-202
EM LC EC FE CL MT
*1: These numbers are prescribed by SAE J2012. *2: When the fail-safe operation occurs, the MIL illuminates. *3: The MIL illuminates when both the Revolution sensor signal and the Vehicle speed sensor signal meet the fail-safe condition at the same time.
AT-5
PRECAUTIONS
Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TENSIONER
Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TENSIONER
NCAT0220
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER used along with a seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. The SRS system composition which is available to INFINITI G20 is as follows: For a frontal collision The Supplemental Restraint System consists of driver air bag module (located in the center of the steering wheel), front passenger air bag module (located on the instrument panel on passenger side), seat belt pre-tensioners, a diagnosis sensor unit, warning lamp, wiring harness and spiral cable. For a side collision The Supplemental Restraint System consists of side air bag module (located in the outer side of front seat), satellite sensor, diagnosis sensor unit (one of components of air bags for a frontal collision), wiring harness, warning lamp (one of components of air bags for a frontal collision). Information necessary to service the system safely is included in the RS section of this Service Manual. WARNING: To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized INFINITI dealer. Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the RS section. Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. Spiral cable and wiring harnesses (except SEAT BELT PRE-TENSIONER) covered with yellow insulation tape either just before the harness connectors or for the complete harness are related to the SRS.
Precautions for On Board Diagnostic (OBD) System of A/T and Engine
NCAT0198
The ECM has an on board diagnostic system. It will light up the malfunction indicator lamp (MIL) to warn the driver of a malfunction causing emission deterioration. CAUTION: Be sure to turn the ignition switch OFF and disconnect the negative battery terminal before any repair or inspection work. The open/short circuit of related switches, sensors, solenoid valves, etc. will cause the MIL to light up. Be sure to connect and lock the connectors securely after work. A loose (unlocked) connector will cause the MIL to light up due to an open circuit. (Be sure the connector is free from water, grease, dirt, bent terminals, etc.) Be sure to route and secure the harnesses properly after work. Interference of the harness with a bracket, etc. may cause the MIL to light up due to a short circuit. Be sure to connect rubber tubes properly after work. A misconnected or disconnected rubber tube may cause the MIL to light up due to a malfunction of the EGR system or fuel injection system, etc. Be sure to erase the unnecessary malfunction information (repairs completed) from the TCM and ECM before returning the vehicle to the customer.
Precautions
NCAT0003
Before connecting or disconnecting the TCM harness connector, turn ignition switch OFF and disconnect negative battery terminal. Failure to do so may damage the TCM. Because battery voltage is applied to TCM even if ignition switch is turned off.
SEF289H
AT-6
PRECAUTIONS
Precautions (Contd)
When connecting or disconnecting pin connectors into or from TCM, take care not to damage pin terminals (bend or break). Make sure that there are not any bends or breaks on TCM pin terminal, when connecting pin connectors.
GI MA EM
AAT470A
LC
Before replacing TCM, perform TCM input/output signal inspection and make sure whether TCM functions properly or not. (See page AT-99.)
EC FE CL
MEF040DA
MT
After performing each TROUBLE DIAGNOSIS, perform DTC (Diagnostic Trouble Code) CONFIRMATION PROCEDURE. The DTC should not be displayed in the DTC CONFIRMATION PROCEDURE if the repair is completed.
AX SU BR
SAT964I
Before proceeding with disassembly, thoroughly clean the outside of the transaxle. It is important to prevent the internal parts from becoming contaminated by dirt or other foreign matter. Disassembly should be done in a clean work area. Use lint-free cloth or towels for wiping parts clean. Common shop rags can leave fibers that could interfere with the operation of the transaxle. Place disassembled parts in order for easier and proper assembly. All parts should be carefully cleaned with a general purpose, non-flammable solvent before inspection or reassembly. Gaskets, seals and O-rings should be replaced any time the transaxle is disassembled. It is very important to perform functional tests whenever they are indicated. The valve body contains precision parts and requires extreme care when parts are removed and serviced. Place disassembled valve body parts in order for easier and proper assembly. Care will also prevent springs and small parts from becoming scattered or lost. Properly installed valves, sleeves, plugs, etc. will slide along bores in valve body under their own weight. Before assembly, apply a coat of recommended ATF to all
ST RS BT HA SC EL IDX
AT-7
PRECAUTIONS
Precautions (Contd)
parts. Apply petroleum jelly to protect O-rings and seals, or hold bearings and washers in place during assembly. Do not use grease. Extreme care should be taken to avoid damage to O-rings, seals and gaskets when assembling. Replace ATF cooler if excessive foreign material is found in oil pan or clogging strainer. Refer to AT-9, ATF COOLER SERVICE. After overhaul, refill the transaxle with new ATF. When the A/T drain plug is removed, only some of the fluid is drained. Old A/T fluid will remain in torque converter and ATF cooling system. Always follow the procedures under Changing A/T Fluid in the MA section when changing A/T fluid. Refer to MA-23, Changing A/T Fluid.
Service Notice or Precautions

FAIL-SAFE
The TCM has an electronic Fail-Safe (limp home mode). This allows the vehicle to be driven even if a major electrical input/output device circuit is damaged. Under Fail-Safe, the vehicle always runs in third gear, even with a shift lever position of 1, 2 or D. The customer may complain of sluggish or poor acceleration. When the ignition key is turned ON following Fail-Safe operation, O/D OFF indicator lamp blinks for about 8 seconds. [For TCM SELF-DIAGNOSTIC PROCEDURE (No Tools), refer to AT-49.] The blinking of the O/D OFF indicator lamp for about 8 seconds will appear only once and be cleared. The customer may resume normal driving conditions. Always follow the WORK FLOW (Refer to AT-60). The SELF-DIAGNOSIS results will be as follows: The first SELF-DIAGNOSIS will indicate damage to the vehicle speed sensor or the revolution sensor. During the next SELF-DIAGNOSIS, performed after checking the sensor, no damages will be indicated.
TORQUE CONVERTER SERVICE
NCAT0004S02
The torque converter should be replaced under any of the following conditions: External leaks in the hub weld area. Converter hub is scored or damaged. Converter pilot is broken, damaged or fits poorly into crankshaft. Steel particles are found after flushing the cooler and cooler lines. Pump is damaged or steel particles are found in the converter. Vehicle has TCC shudder and/or no TCC apply. Replace only after all hydraulic and electrical diagnoses have been made. (Converter clutch material may be glazed.) Converter is contaminated with engine coolant containing antifreeze. Internal failure of stator roller clutch. Heavy clutch debris due to overheating (blue converter). Steel particles or clutch lining material found in fluid filter or on magnet when no internal parts in unit are worn or damaged indicates that lining material came from converter. The torque converter should not be replaced if: The fluid has an odor, is discolored, and there is no evidence of metal or clutch facing particles. The threads in one or more of the converter bolt holes are damaged.
AT-8
PRECAUTIONS
Service Notice or Precautions (Contd)
Transaxle failure did not display evidence of damaged or worn internal parts, steel particles or clutch plate lining material in unit and inside the fluid filter. Vehicle has been exposed to high mileage (only). The exception may be where the torque converter clutch dampener plate lining has seen excess wear by vehicles operated in heavy and/or constant traffic, such as taxi, delivery or police use.
NCAT0004S03
GI MA EM LC
ATF COOLER SERVICE
Replace ATF cooler if excessive foreign material is found in oil pan or clogging strainer. Replace radiator lower tank (which includes ATF cooler) with a new one and flush cooler line using cleaning solvent and compressed air. Refer to LC-14, Radiator.
OBD-II SELF-DIAGNOSIS

NCAT0004S04
*:
A/T self-diagnosis is performed by the TCM in combination with the ECM. The results can be read through the blinking pattern of the O/D OFF indicator or the malfunction indicator lamp (MIL). Refer to the table on AT-41 for the indicator used to display each self-diagnostic result. The self-diagnostic results indicated by the MIL are automatically stored in both the ECM and TCM memories. Always perform the procedure HOW TO ERASE DTC on AT-38 to complete the repair and avoid unnecessary blinking of the MIL. The following self-diagnostic items can be detected using ECM self-diagnostic results mode* only when the O/D OFF indicator lamp does not indicate any malfunctions. PNP switch A/T 1st, 2nd, 3rd, or 4th gear function A/T TCC S/V function (lock-up). For details of OBD-II, refer to EC-67, ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION. Certain systems and components, especially those related to OBD, may use a new style slidelocking type harness connector. For description and how to disconnect, refer to EL-5, HARNESS CONNECTOR.
EC FE CL MT
Wiring Diagrams and Trouble Diagnosis

When you read wiring diagrams, refer to the following: GI-11, HOW TO READ WIRING DIAGRAMS EL-9, POWER SUPPLY ROUTING When you perform trouble diagnosis, refer to the following: GI-35, HOW TO FOLLOW TEST GROUPS IN TROUBLE DIAGNOSES GI-24, HOW TO PERFORM EFFICIENT DIAGNOSIS FOR AN ELECTRICAL INCIDENT
NCAT0005
AT-9
PREPARATION
Special Service Tools
Special Service Tools

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here. Tool number (Kent-Moore No.) Tool name (J34301-C) Oil pressure gauge set 1 (J34301-1) Oil pressure gauge 2 (J34301-2) Hoses 3 (J34298) Adapter 4 (J34282-2) Adapter 5 (790-301-1230-A) 60 Adapter 6 (J34301-15) Square socket KV31103000 (J38982) Drift Description
NCAT0006
Measuring line pressure and governor pressure
AAT896
Installing differential oil seal (Use with ST35325000.) a: 59 mm (2.32 in) dia. b: 49 mm (1.93 in) dia.
NT105
ST35325000 ( Drift
Installing differential oil seal (Use with KV31103000.) a: 215 mm (8.46 in) b: 25 mm (0.98 in) dia. c: M12 x 1.5P
NT417
KV38107700 (J39027) Preload adapter

NT087
Measuring turning torque of final drive assembly Measuring clearance between side gear and differential case with washer Selecting differential side bearing adjusting shim Removing and installing clutch return spring a: 320 mm (12.60 in) b: 174 mm (6.85 in)
KV31103200 (J34285-A and J3428587) Clutch spring compressor
NT423
ST23540000 (J25689-A) Pin punch
Removing and installing parking rod plate, manual plate and differential pinion mate shaft retaining pins a: 2.3 mm (0.091 in) dia. b: 4 mm (0.16 in) dia.
NT442
AT-10
PREPARATION
Special Service Tools (Contd)
Tool number (Kent-Moore No.) Tool name KV32101000 (J25689-A) Pin punch
Description Installing throttle lever and manual shaft retaining pins a: 4 mm (0.16 in) dia.
GI MA EM
NT410
ST25710000 ( Pin punch
Aligning groove of manual shaft and hole of transmission case a: 2 mm (0.08 in) dia.
LC EC
NT410
ST3306S001 (J22888-D) Differential side bearing puller set 1 ST33051001 (J22888-D) Puller 2 ST33061000 (J8107-2) Adapter KV381054S0 (J34286) Puller
Removing differential side bearing inner race a: 39 mm (1.54 in) dia. b: 29.5 mm (1.161 in) dia. c: 130 mm (5.12 in) d: 135 mm (5.31 in) e: 120 mm (4.72 in)
FE CL MT
NT745
Removing idler gear bearing outer race Removing differential side oil seals Removing differential side bearing outer race Removing needle bearing from bearing retainer a: 250 mm (9.84 in) b: 160 mm (6.30 in)
AX SU BR
NT414
ST27180001 (J25726-A) Puller
Removing idler gear a: 100 mm (3.94 in) b: 110 mm (4.33 in) c: M8 x 1.25P
ST RS
NT424
BT
Removing reduction gear bearing inner race a: 90 mm (3.54 in) dia. b: 50 mm (1.97 in) dia.
ST30031000 (J22912-1) Puller
HA SC
NT411
ST35272000 (J26092) Drift
Installing reduction gear bearing inner race Installing idler gear bearing inner race a: 72 mm (2.83 in) dia. b: 35.5 mm (1.398 in) dia.
EL IDX
NT426
AT-11
PREPARATION
Special Service Tools (Contd)
Tool number (Kent-Moore No.) Tool name ST37830000 ( Drift )
Description Installing idler gear bearing outer race a: 62 mm (2.44 in) dia. b: 39 mm (1.54 in) dia.
NT427
ST35321000 ( Drift
Installing output shaft bearing a: 49 mm (1.93 in) dia. b: 41 mm (1.61 in) dia.
NT073
ST30633000 ( Drift
Installing differential side bearing outer race a: 67 mm (2.64 in) dia. b: 49 mm (1.93 in) dia.
NT073
ST35271000 (J26091) Drift
Installing idler gear a: 72 mm (2.83 in) dia. b: 63 mm (2.48 in) dia.
NT115
ST33400001 (J26082) Drift
Installing oil pump housing oil seal a: 60 mm (2.36 in) dia. b: 47 mm (1.85 in) dia.
NT115
Commercial Service Tools

Tool name Puller Description
NCAT0007
Removing idler gear bearing inner race Removing and installing band servo piston snap ring
NT077
AT-12
PREPARATION
Commercial Service Tools (Contd)
Tool name Drift Description Removing idler gear bearing inner race a: 34 mm (1.34 in) dia.
GI MA
NT109
Drift
Installing differential left side bearing a: 86 mm (3.39 in) dia. b: 80 mm (3.15 in) dia.
EM LC
NT115
Drift
Installing differential right side bearing a: 46 mm (1.81 in) dia. b: 40 mm (1.57 in) dia.
EC FE
NT115
CL MT
AT-13
OVERALL SYSTEM
A/T Electrical Parts Location
A/T Electrical Parts Location
NCAT0008
SAT841J
AT-14
OVERALL SYSTEM
Circuit Diagram
Circuit Diagram
NCAT0009
TAT269
AT-15
OVERALL SYSTEM
Cross-sectional View RE4F03B
Cross-sectional View RE4F03B
NCAT0011
SAT842J
AT-16
OVERALL SYSTEM
Cross-sectional View RE4F03W
Cross-sectional View RE4F03W
NCAT0217
SAT843J
AT-17
OVERALL SYSTEM
Hydraulic Control Circuit
Hydraulic Control Circuit
NCAT0012
SAT844J
AT-18
OVERALL SYSTEM
Shift Mechanism
Shift Mechanism
CONSTRUCTION
GI MA EM LC EC FE CL
SAT998I
MT
1. 2. 3. 4. 5. 6. 7. 8.
Torque converter Oil pump Input shaft Brake band Reverse clutch High clutch Front sun gear Front pinion gear
9. 10. 11. 12. 13. 14. 15. 16.
Front internal gear Front planetary carrier Rear sun gear Rear pinion gear Rear internal gear Rear planetary carrier Forward clutch Forward one-way clutch
17. 18. 19. 20. 21. 22. 23. 24.
Overrun clutch Low one-way clutch Low & reverse brake Parking pawl Parking gear Output shaft Idle gear Output gear
FUNCTION OF CLUTCH AND BRAKE

Clutch and brake components 5 Reverse clutch 6 High clutch 15 Forward clutch 17 Overrun clutch 4 Brake band 16 Forward one-way clutch 18 Low one-way clutch 19 Low & reverse brake R/C H/C F/C O/C B/B F/O.C L/O.C L & R/B Abbr. Function To transmit input power to front sun gear 7. To transmit input power to front planetary carrier 10. To connect front planetary carrier 10 with forward one-way clutch 16. To connect front planetary carrier 10 with rear internal gear 13. To lock front sun gear 7.
NCAT0013S03
When forward clutch 15 is engaged, to stop rear internal gear 13 from rotating in opposite direction against engine revolution. To stop front planetary carrier 10 from rotating in opposite direction against engine revolution. To lock front planetary carrier 10.
AT-19
OVERALL SYSTEM
Shift Mechanism (Contd)
CLUTCH AND BAND CHART

Reverse Shift position clutch 5 High clutch 6 Forward clutch 15 Overrun clutch 17 Band servo 2nd apply 3rd release 4th apply Forward one-way clutch 16 Low oneway clutch 18 Low & reverse Lock-up brake 19
NCAT0013S04
Remarks
P R N 1st 2nd D*4 3rd 4th 1st 2 2nd 1st 1 2nd k k k B k k k k k C k k k D A k k *1D *1A *1A k *2C *3C C C k B B B k B B B B *5 k k B k k
PARK POSITION REVERSE POSITION NEUTRAL POSITION Automatic shift 1k2k3 k4 Automatic shift 1k2 Locks (held stationary) in 1st speed 1g2
*1: Operates when overdrive control switch is set in OFF position. *2: Oil pressure is applied to both 2nd apply side and 3rd release side of band servo piston. However, brake band does not contract because oil pressure area on the release side is greater than that on the apply side. *3: Oil pressure is applied to 4th apply side in condition *2 above, and brake band contracts. *4: A/T will not shift to 4th when overdrive control switch is set in OFF position. *5: Operates when overdrive control switch is OFF. k : Operates. A: Operates when throttle opening is less than 3/16, activating engine brake. B: Operates during progressive acceleration. C: Operates but does not affect power transmission. D: Operates when throttle opening is less than 3/16, but does not affect engine brake.
AT-20
OVERALL SYSTEM
POWER TRANSMISSION N and P Positions

=NCAT0013S02 NCAT0013S0201
N position Power from the input shaft is not transmitted to the output shaft because the clutches do not operate. P position Similar to the N position, the clutches do not operate. The parking pawl engages with the parking gear to mechanically hold the output shaft so that the power train is locked.
SAT991I
AT-21
OVERALL SYSTEM
11 Position
Forward clutch Forward one-way clutch Overrun clutch Low and reverse brake
=NCAT0013S0202
As overrun clutch engages, rear internal gear is locked by the operation of low and reverse brake. This is different from that of D1 and 21. Overrun clutch always engages, therefore engine brake can be obtained when decelerating.
Engine brake
SAT374J
AT-22
OVERALL SYSTEM
D1 and 21 Positions
Forward one-way clutch Forward clutch Low one-way clutch Overrun clutch engagement conditions (Engine brake)
=NCAT0013S0203
Rear internal gear is locked to rotate counterclockwise because of the functioning of these three clutches. D1: Overdrive control switch OFF and throttle opening is less than 3/16 21: Always engaged At D1 and 21 positions, engine brake is not activated due to free turning of low oneway clutch.
AX SU BR ST RS
SAT377J
BT HA SC EL IDX
AT-23
OVERALL SYSTEM
D2, 22 and 12 Positions

Forward clutch Forward one-way clutch Brake band Overrun clutch engagement conditions
=NCAT0013S0204
Rear sun gear drives rear planetary carrier and combined front internal gear. Front internal gear now rotates around front sun gear accompanying front planetary carrier. As front planetary carrier transfers the power to rear internal gear through forward clutch and forward one-way clutch, this rotation of rear internal gear increases the speed of rear planetary carrier compared with that of the 1st speed. D2: Overdrive control switch OFF and throttle opening is less than 3/16 22 and 12: Always engaged
SAT378J
AT-24
OVERALL SYSTEM
D3 Position
High clutch Forward clutch Forward one-way clutch Overrun clutch engagement conditions
=NCAT0013S0205
Input power is transmitted to front planetary carrier through high clutch. And front planetary carrier is connected to rear internal gear by operation of forward clutch and forward one-way clutch. This rear internal gear rotation and another input (the rear sun gear) accompany rear planetary carrier to turn at the same speed. D3: Overdrive control switch OFF and throttle opening is less than 3/16
SAT379J
AT-25
OVERALL SYSTEM
D4 (OD) Position
High clutch Brake band Forward clutch (Does not affect power transmission) Engine brake
=NCAT0013S0206
Input power is transmitted to front carrier through high clutch. This front carrier turns around the sun gear which is fixed by brake band and makes front internal gear (output) turn faster. At D4 position, there is no one-way clutch in the power transmission line and engine brake can be obtained when decelerating.
SAT380J
AT-26
OVERALL SYSTEM
R Position
Reverse clutch Low and reverse brake
=NCAT0013S0207
Front planetary carrier is stationary because of the operation of low and reverse brake. Input power is transmitted to front sun gear through reverse clutch, which drives front internal gear in the opposite direction. As there is no one-way clutch in the power transmission line, engine brake can be obtained when decelerating.
Engine brake
SAT381J
AT-27
OVERALL SYSTEM
Control System
Control System
OUTLINE
=NCAT0014 NCAT0014S01
The automatic transaxle senses vehicle operating conditions through various switches and sensors. It always controls the optimum shift position and reduces shifting and lock-up shocks.
SWITCHES & SENSORS PNP switch Throttle position sensor Closed throttle position switch Wide open throttle position switch Engine speed signal A/T fluid temperature sensor Revolution sensor Vehicle speed sensor Overdrive control switch ASCD control unit Stop lamp switch TCM Shift control Line pressure control Lock-up control Overrun clutch control Timing control Fail-safe control Self-diagnosis CONSULT-II communication line control Duet-EA control ACTUATORS
Shift solenoid valve A Shift solenoid valve B Overrun clutch solenoid valve Torque converter clutch solenoid valve Line pressure solenoid valve O/D OFF indicator lamp
CONTROL SYSTEM
NCAT0014S02
SAT879J
AT-28
OVERALL SYSTEM
Control System (Contd)
TCM FUNCTION
The function of the TCM is to: Receive input signals sent from various switches and sensors. Determine required line pressure, shifting point, lock-up operation, and engine brake operation. Send required output signals to the respective solenoids.
=NCAT0014S03
GI MA
NCAT0014S04
INPUT/OUTPUT SIGNAL OF TCM

Sensors, switches and solenoid valves PNP switch Throttle position sensor Closed throttle position switch Wide open throttle position switch Engine speed signal A/T fluid temperature sensor Input Revolution sensor Vehicle speed sensor Overdrive control switch ASCD control unit Stop lamp switch Shift solenoid valve A/B Line pressure solenoid valve Output Torque converter clutch solenoid valve Overrun clutch solenoid valve O/D OFF indicator lamp Function Detects select lever position and sends a signal to TCM. Detects throttle valve position and sends a signal to TCM.
EM LC EC FE CL MT
Detects throttle valves fully-closed position and sends a signal to TCM. Detects a throttle valve position of greater than 1/2 of full throttle and sends a signal to TCM. From ECM. Detects transmission fluid temperature and sends a signal to TCM. Detects output shaft rpm and sends a signal to TCM. Used as an auxiliary vehicle speed sensor. Sends a signal when revolution sensor (installed on transmission) malfunctions. Sends a signal, which prohibits a shift to D4 (overdrive) position, to the TCM. Sends the cruise signal and D4 (overdrive) cancellation signal from ASCD control unit to TCM. Releases lock-up system when depressing pedal in lock-up condition. Selects shifting point suited to driving conditions in relation to a signal sent from TCM. Regulates (or decreases) line pressure suited to driving conditions in relation to a signal sent from TCM. Regulates (or decreases) lock-up pressure suited to driving conditions in relation to a signal sent from TCM. Controls an engine brake effect suited to driving conditions in relation to a signal sent from TCM. Shows TCM faults, when A/T control components malfunction.
AX SU BR ST RS BT HA
Control Mechanism
LINE PRESSURE CONTROL
SC EL IDX
TCM has various line pressure control characteristics to match the driving conditions. An ON-OFF duty signal is sent to the line pressure solenoid valve based on TCM characteristics. Hydraulic pressure on the clutch and brake is electronically controlled through the line pressure solenoid valve to accommodate engine torque. This results in smooth shift operation.
AT-29
OVERALL SYSTEM
Control Mechanism (Contd)
Normal Control
NCAT0015S0101
The line pressure to throttle opening characteristics is set for suitable clutch operation.
SAT003J
Back-up Control (Engine brake)
NCAT0015S0102
If the selector lever is shifted to 2 position while driving in D4 (OD) or D3, great driving force is applied to the clutch inside the transmission. Clutch operating pressure (line pressure) must be increased to deal with this driving force.
SAT004J
During Shift Change
NCAT0015S0103
The line pressure is temporarily reduced corresponding to a change in engine torque when shifting gears (that is, when the shift solenoid valve is switched for clutch operation) to reduce shifting shock.
SAT005J
At Low Fluid Temperature
NCAT0015S0104
Fluid viscosity and frictional characteristics of the clutch facing change with fluid temperature. Clutch engaging or band-contacting pressure is compensated for, according to fluid temperature, to stabilize shifting quality.
The line pressure is reduced below 60C (140F) to prevent shifting shock due to low viscosity of automatic transmission fluid when temperature is low.
SAT006J
AT-30
OVERALL SYSTEM
Line pressure is increased to a maximum irrespective of the throttle opening when fluid temperature drops to 10C (14F). This pressure rise is adopted to prevent a delay in clutch and brake operation due to extreme drop of fluid viscosity at low temperature.
GI MA EM
SAT007J
LC
SHIFT CONTROL
NCAT0015S02
The shift is regulated entirely by electronic control to accommodate vehicle speed and varying engine operations. This is accomplished by electrical signals transmitted by the revolution sensor and throttle position sensor. This results in improved acceleration performance and fuel economy.
EC FE CL MT
Control of Shift Solenoid Valves A and B
NCAT0015S0201
The TCM activates shift solenoid valves A and B according to signals from the throttle position sensor and revolution sensor to select the optimum gear position on the basis of the shift schedule memorized in the TCM. The shift solenoid valve performs simple ON-OFF operation. When set to ON, the drain circuit closes and pilot pressure is applied to the shift valve.
AX SU BR
SAT008J
Relation Between Shift Solenoid Valves A and B and ST Gear Positions NCAT0015S0203
Gear position Shift solenoid valve D1, 21, 11 A B ON (Closed) ON (Closed) D2, 22, 12 OFF (Open) ON (Closed) D3 OFF (Open) OFF (Open) D4 (OD) ON (Closed) OFF (Open) N-P ON (Closed) ON (Closed)
RS BT HA
NCAT0015S0202
Control of Shift Valves A and B
SC EL IDX
SAT009J
AT-31
OVERALL SYSTEM
Pilot pressure generated by the operation of shift solenoid valves A and B is applied to the end face of shift valves A and B. The drawing above shows the operation of shift valve B. When the shift solenoid valve is ON, pilot pressure applied to the end face of the shift valve overcomes spring force, moving the valve upward.
LOCK-UP CONTROL
NCAT0015S03
The torque converter clutch piston in the torque converter is locked to eliminate torque converter slip to increase power transmission efficiency. The solenoid valve is controlled by an ON-OFF duty signal sent from the TCM. The signal is converted to an oil pressure signal which controls the torque converter clutch piston.
Conditions for Lock-up Operation
NCAT0015S0301
When vehicle is driven in 4th gear position, vehicle speed and throttle opening are detected. If the detected values fall within the lock-up zone memorized in the TCM, lock-up is performed.
Overdrive control switch Selector lever Gear position Vehicle speed sensor Throttle position sensor Closed throttle position switch A/T fluid temperature sensor D4 ON D position D3 OFF
More than set value Less than set opening OFF More than 40C (104F)
Torque Converter Clutch Solenoid Valve Control
NCAT0015S0302
The torque converter clutch solenoid valve is controlled by the TCM. The plunger closes the drain circuit during the OFF period, and opens the circuit during the ON period. If the percentage of OFF-time increases in one cycle, the pilot pressure drain time is reduced and pilot pressure remains high. The torque converter clutch piston is designed to slip to adjust the ratio of ON-OFF, thereby reducing lock-up shock.
SAT010J
OFF-time INCREASING " Amount of drain DECREASING " Pilot pressure HIGH " Lock-up RELEASING
SAT011J
AT-32
OVERALL SYSTEM
Torque Converter Clutch Control Valve OperationNCAT0015S0303
GI MA EM LC
AAT155A
Lock-up released The OFF-duration of the torque converter clutch solenoid valve is long, and pilot pressure is high. The pilot pressure pushes the end face of the torque converter clutch control valve in combination with spring force to move the valve to the left. As a result, converter pressure is applied to chamber A (torque converter clutch piston release side). Accordingly, the torque converter clutch piston remains unlocked. Lock-up applied When the OFF-duration of the torque converter clutch solenoid valve is short, pilot pressure drains and becomes low. Accordingly, the control valve moves to the right by the pilot pressure of the other circuit and converter pressure. As a result, converter pressure is applied to chamber B, keeping the torque converter clutch piston applied. Also smooth lock-up is provided by transient application and release of the lock-up.
EC FE CL MT
AX SU
OVERRUN CLUTCH CONTROL (ENGINE BRAKE CONTROL)
NCAT0015S04
Forward one-way clutch is used to reduce shifting shocks in downshifting operations. This clutch transmits engine torque to the wheels. However, drive force from the wheels is not transmitted to the engine because the one-way clutch rotates idle. This means the engine brake is not effective. The overrun clutch operates when the engine brake is needed.
BR ST RS BT
Overrun Clutch Operating Conditions

Selector lever position D position 2 position 1 position Gear position D1, D2, D3 gear position 21, 22 gear position 11, 12 gear position At any position Throttle opening Less than 3/16
NCAT0015S0401
HA SC EL IDX
SAT014J
AT-33
OVERALL SYSTEM
Overrun Clutch Solenoid Valve Control
NCAT0015S0402
The overrun clutch solenoid valve is operated by an ON-OFF signal transmitted by the TCM to provide overrun clutch control (engine brake control). When this solenoid valve is ON, the pilot pressure drain port closes. When it is OFF, the drain port opens. During the solenoid valve ON pilot pressure is applied to the end face of the overrun clutch control valve.
SAT015J
Overrun Clutch Control Valve Operation
NCAT0015S0403
When the solenoid valve is ON, pilot pressure is applied to the overrun clutch control valve. This pushes up the overrun clutch control valve. The line pressure is then shut off so that the clutch does not engage. When the solenoid valve is OFF, pilot pressure is not generated. At this point, the overrun clutch control valve moves downward by spring force. As a result, overrun clutch operation pressure is provided by the overrun clutch reducing valve. This causes the overrun clutch to engage. In the 1 position, the overrun clutch control valve remains pushed down so that the overrun clutch is engaged at all times.
SAT016J
Control Valve
FUNCTION OF CONTROL VALVES
Valve name Function
Pressure regulator valve, plug and Regulates oil discharged from the oil pump to provide optimum line pressure for all driving sleeve conditions. Pressure modifier valve and sleeve Pilot valve Accumulator control valve Manual valve Shift valve A Used as a signal supplementary valve to the pressure regulator valve. Regulates pressuremodifier pressure (signal pressure) which controls optimum line pressure for all driving conditions. Regulates line pressure to maintain a constant pilot pressure level which controls lock-up mechanism, overrun clutch, shift timing. Regulates accumulator back-pressure to pressure suited to driving conditions. Directs line pressure to oil circuits corresponding to select positions. Hydraulic pressure drains when the shift lever is in Neutral. Simultaneously switches four oil circuits using output pressure of shift solenoid valve A to meet driving conditions (vehicle speed, throttle opening, etc.). Provides automatic downshifting and up-shifting (1st , 2nd , 3rd , 4th gears/4th , 3rd , 2nd , 1st gears) in combination with shift valve B.
AT-34
OVERALL SYSTEM
Control Valve (Contd)
Valve name Shift valve B Function Simultaneously switches three oil circuits using output pressure of shift solenoid valve B in relation to driving conditions (vehicle speed, throttle opening, etc.). Provides automatic downshifting and up-shifting (1st , 2nd , 3rd , 4th gears/4th , 3rd , 2nd , 1st gears) in combination with shift valve A. Switches hydraulic circuits to prevent engagement of the overrun clutch simultaneously with application of the brake band in D4. (Interlocking occurs if the overrun clutch engages during D4.) Reduces low & reverse brake pressure to dampen engine-brake shock when down-shifting from the 1 position 12 to 11. Reduces oil pressure directed to the overrun clutch and prevents engine-brake shock. In 1 and 2 positions, line pressure acts on the overrun clutch reducing valve to increase the pressure-regulating point, with resultant engine brake capability. Prevents an excessive rise in torque converter pressure. Activates or inactivates the lock-up function. Also provides smooth lock-up through transient application and release of the lock-up system. Dampens the shock encountered when 2nd gear band servo contracts, and provides smooth shifting. Switches oil pressure with 3-2 timing valve according to throttle opening. Reduces shock when down-shifting from 3rd to 2nd and regulates overrun clutch. Regulates oil pressure which causes lock-up when driving at low speeds.
Overrun clutch control valve
1st reducing valve Overrun clutch reducing valve
Torque converter relief valve Torque converter clutch control valve, plug and sleeve 1-2 accumulator valve and piston 3-2 timing valve Shuttle control valve Cooler check valve
AT-35
ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION

Introduction
Introduction
NCAT0017
The A/T system has two self-diagnostic systems. The first is the emission-related on board diagnostic system (OBD-II) performed by the TCM in combination with the ECM. The malfunction is indicated by the MIL (malfunction indicator lamp) and is stored as a DTC in the ECM memory but not the TCM memory. The second is the TCM original self-diagnosis indicated by the O/D OFF indicator lamp. The malfunction is stored in the TCM memory. The detected items are overlapped with OBD-II self-diagnostic items. For detail, refer to AT-41.
OBD-II Function for A/T System
NCAT0018
The ECM provides emission-related on board diagnostic (OBD-II) functions for the A/T system. One function is to receive a signal from the TCM used with OBD-related parts of the A/T system. The signal is sent to the ECM when a malfunction occurs in the corresponding OBD-related part. The other function is to indicate a diagnostic result by means of the MIL (malfunction indicator lamp) on the instrument panel. Sensors, switches and solenoid valves are used as sensing elements. The MIL automatically illuminates in One or Two Trip Detection Logic when a malfunction is sensed in relation to A/T system parts.
One or Two Trip Detection Logic of OBD-II

ONE TRIP DETECTION LOGIC
If a malfunction is sensed during the first test drive, the MIL will illuminate and the malfunction will be stored in the ECM memory as a DTC. The TCM is not provided with such a memory function.
TWO TRIP DETECTION LOGIC
NCAT0019S02
When a malfunction is sensed during the first test drive, it is stored in the ECM memory as a 1st trip DTC (diagnostic trouble code) or 1st trip freeze frame data. At this point, the MIL will not illuminate. First Trip If the same malfunction as that experienced during the first test drive is sensed during the second test drive, the MIL will illuminate. Second Trip A/T-related parts for which the MIL illuminates during the first or second test drive are listed below.
MIL Items One trip detection Shift solenoid valve A DTC: P0750 Shift solenoid valve B DTC: P0755 Throttle position sensor or switch DTC: P1705 Except above X X X X Two trip detection
The trip in the One or Two Trip Detection Logic means a driving mode in which self-diagnosis is performed during vehicle operation.
OBD-II Diagnostic Trouble Code (DTC)

HOW TO READ DTC AND 1ST TRIP DTC
DTC and 1st trip DTC can be read by the following methods. ( with CONSULT-II or GST) CONSULT-II or GST (Generic Scan Tool) Examples: P0705, P0710, P0720, P0725, etc. These DTCs are prescribed by SAE J2012. (CONSULT-II also displays the malfunctioning component or system.) 1st trip DTC No. is the same as DTC No. Output of the diagnostic trouble code indicates that the indicated circuit has a malfunction. However, in case of the Mode II and GST they do not indicate whether the malfunction is still occurring or occurred in the past and returned to normal. CONSULT-II can identify them as shown below. Therefore, using CONSULT-II (if available) is recommended. Samples of CONSULT-II display for DTC and 1st trip DTC are shown in the next page. DTC or 1st trip DTC of a malfunction is displayed in SELF DIAGNOSIS mode for ENGINE with CONSULT-II. Time data indicates how many times the vehicle was driven after the last detection of a DTC.
AT-36

OBD-II Diagnostic Trouble Code (DTC) (Contd)
GI MA EM
SAT014K
LC EC FE CL MT
If the DTC is being detected currently, the time data will be 0.
SAT015K
If a 1st trip DTC is stored in the ECM, the time data will be 245.
AX SU BR ST
SAT016K
RS
NCAT0020S0101
Freeze Frame Data and 1st Trip Freeze Frame Data
The ECM has a memory function, which stores the driving condition such as fuel system status, calculated load value, engine coolant temperature, short term fuel trim, long term fuel trim, engine speed and vehicle speed at the moment the ECM detects a malfunction. Data which are stored in the ECM memory, along with the 1st trip DTC, are called 1st trip freeze frame data, and the data, stored together with the DTC data, are called freeze frame data and displayed on CONSULT-II or GST. The 1st trip freeze frame data can only be displayed on the CONSULT-II screen, not on the GST. For detail, refer to EC-88, CONSULT-II. Only one set of freeze frame data (either 1st trip freeze frame data of freeze frame data) can be stored in the ECM. 1st trip freeze frame data is stored in the ECM memory along with the 1st trip DTC. There is no priority for 1st trip freeze frame data and it is updated each time a different 1st trip DTC is detected. However, once freeze frame data (2nd trip detection/MIL on) is stored in the ECM memory, 1st trip freeze frame data is no longer stored. Remember, only one set of freeze frame data can be stored in the ECM. The ECM has the following priorities to update the data.
BT HA SC EL IDX
AT-37

Priority 1 2 3 Freeze frame data Items Misfire DTC: P0300 - P0306 Fuel Injection System Function DTC: P0171, P0172, P0174, P0175 Except the above items (Includes A/T related items) 1st trip freeze frame data
Both 1st trip freeze frame data and freeze frame data (along with the DTCs) are cleared when the ECM memory is erased.
HOW TO ERASE DTC
NCAT0020S02
The diagnostic trouble code can be erased by CONSULT-II, GST or ECM DIAGNOSTIC TEST MODE as described following. If the battery terminal is disconnected, the diagnostic trouble code will be lost within 24 hours. When you erase the DTC, using CONSULT-II or GST is easier and quicker than switching the mode selector on the ECM. The following emission-related diagnostic information is cleared from the ECM memory when erasing DTC related to OBD-II. For details, refer to EC-68, Emission-related Diagnostic Information. Diagnostic trouble codes (DTC) 1st trip diagnostic trouble codes (1st trip DTC) Freeze frame data 1st trip freeze frame data System readiness test (SRT) codes Test values
HOW TO ERASE DTC (WITH CONSULT-II)
If a DTC is displayed for both ECM and TCM, it needs to be erased for both ECM and TCM. 1. If the ignition switch stays ON after repair work, be sure to turn ignition switch OFF once. Wait at least 10 seconds and then turn it ON (engine stopped) again. 2. Turn CONSULT-II ON and touch A/T. 3. Touch SELF DIAGNOSIS. 4. Touch ERASE. (The DTC in the TCM will be erased.) Then touch BACK twice. 5. Touch ENGINE. 6. Touch SELF DIAGNOSIS. 7. Touch ERASE. (The DTC in the ECM will be erased.)
NCAT0020S03
AT-38

AX
SAT286K
SU BR ST RS BT HA SC EL IDX
HOW TO ERASE DTC (WITH GST)
NCAT0020S04
1. If the ignition switch stays ON after repair work, be sure to turn ignition switch OFF once. Wait at least 10 seconds and then turn it ON (engine stopped) again. 2. Perform OBD-II SELF-DIAGNOSTIC PROCEDURE (No Tools). Refer to AT-49. (The engine warm-up step can be skipped when performing the diagnosis only to erase the DTC.) 3. Select Mode 4 with Generic Scan Tool (GST). For details, refer to EC-101, Generic Scan Tool (GST).
HOW TO ERASE DTC (NO TOOLS)
NCAT0020S05
1. If the ignition switch stays ON after repair work, be sure to turn ignition switch OFF once. Wait at least 10 seconds and then turn it ON (engine stopped) again. 2. Perform TCM SELF-DIAGNOSTIC PROCEDURE (No Tools). Refer to AT-49. (The engine warm-up step can be skipped when performing the diagnosis only to erase the DTC.)
AT-39

Malfunction Indicator Lamp (MIL)
Malfunction Indicator Lamp (MIL)

1.
=NCAT0021
2.
SAT964I
The malfunction indicator lamp will light up when the ignition switch is turned ON without the engine running. This is for checking the lamp. If the malfunction indicator lamp does not light up, refer to EL-98, Warning Lamps. (Or see MIL & CONSULT-II in EC section. Refer to EC-81, Description, Malfunction Indicator Lamp (MIL) and EC-88, CONSULT-II.) When the engine is started, the malfunction indicator lamp should go off. If the lamp remains on, the on board diagnostic system has detected an emission-related (OBD-II) malfunction. For detail, refer to EC-67, ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION.
CONSULT-II
NCAT0022
After performing SELF-DIAGNOSTIC PROCEDURE (WITH CONSULT-II) (AT-41), place check marks for results on the DIAGNOSTIC WORKSHEET, AT-58. Reference pages are provided following the items. NOTICE: 1) The CONSULT-II electrically displays shift timing and lock-up timing (that is, operation timing of each solenoid). Check for time difference between actual shift timing and the CONSULT-II display. If the difference is noticeable, mechanical parts (except solenoids, sensors, etc.) may be malfunctioning. Check mechanical parts using applicable diagnostic procedures. 2) Shift schedule (which implies gear position) displayed on CONSULT-II and that indicated in Service Manual may differ slightly. This occurs because of the following reasons: Actual shift schedule has more or less tolerance or allowance, Shift schedule indicated in Service Manual refers to the point where shifts start, and Gear position displayed on CONSULT-II indicates the point where shifts are completed. 3) Shift solenoid valve A or B is displayed on CONSULT-II at the start of shifting. Gear position is displayed upon completion of shifting (which is computed by TCM). 4) Additional CONSULT-II information can be found in the Operation Manual supplied with the CONSULT-II unit.
AT-40

CONSULT-II (Contd)
SELF-DIAGNOSTIC PROCEDURE (WITH CONSULT-II) NCAT0022S02

1. Turn on CONSULT-II and touch ENGINE for OBD-II detected items or touch A/T for TCM self-diagnosis. If A/T is not displayed, check TCM power supply and ground circuit. Refer to AT-99. If result is NG, refer to EL-9, POWER SUPPLY ROUTING.
GI MA EM
SAT014K
LC
2. Touch SELF DIAGNOSIS. Display shows malfunction experienced since the last erasing operation. CONSULT-II performs real time diagnosis. Also, any malfunction detected while in this mode will be displayed at real time.
EC FE CL
SAT987J
MT
SELF-DIAGNOSTIC RESULT TEST MODE
TCM self-diagnosis
NCAT0022S03
OBD-II (DTC)
Detected items (Screen terms for CONSULT-II, SELF DIAGNOSIS test mode) Malfunction is detected when ... Available by O/D OFF indicator lamp or A/T on CONSULT-II Available by malfunction indicator lamp*2, ENGINE on CONSULT-II or GST P0705
AX SU BR ST
X P0720
A/T
ENGINE TCM does not receive the correct voltage signal (based on the gear position) from the switch. TCM does not receive the proper voltage signal from the sensor.
PNP switch circuit Revolution sensor VHCL SPEED SENA/T VEH SPD SEN/CIR AT PNP SW/CIRC
RS BT HA
Vehicle speed sensor (Meter) VHCL SPEED SENMTR A/T 1st gear function A/T 2nd gear function A/T 3rd gear function A/T 3RD GR FNCTN A/T 2ND GR FNCTN
TCM does not receive the proper voltage signal from the sensor.
A/T cannot be shifted to the 1st gear position even if electrical A/T 1ST GR FNCTN circuit is good. A/T cannot be shifted to the 2nd gear position even if electrical circuit is good. A/T cannot be shifted to the 3rd gear position even if electrical circuit is good.
P0731*1
SC
P0732*1
EL IDX
P0733*1
AT-41

CONSULT-II (Contd)
TCM self-diagnosis Detected items (Screen terms for CONSULT-II, SELF DIAGNOSIS test mode) Malfunction is detected when ... Available by O/D OFF indicator lamp or A/T on CONSULT-II Available by malfunction indicator lamp*2, ENGINE on CONSULT-II or GST OBD-II (DTC)
A/T
ENGINE A/T cannot be shifted to the 4th gear position even if electrical circuit is good. A/T cannot perform lock-up even if electrical circuit is good.
A/T 4th gear function A/T 4TH GR FNCTN
P0734*1
A/T TCC S/V function (lock-up) Shift solenoid valve A SHIFT SOLENOID/V A Shift solenoid valve B SHIFT SOLENOID/V B SFT SOL B/CIRC SFT SOL A/CIRC A/T TCC S/V FNCTN
P0744*1
TCM detects an improper voltage drop when it tries to operate the solenoid valve. TCM detects an improper voltage drop when it tries to operate the solenoid valve. TCM detects an improper voltage drop when it tries to operate the solenoid valve. TCM detects an improper voltage drop when it tries to operate the solenoid valve. TCM detects an improper voltage drop when it tries to operate the solenoid valve. TCM receives an excessively low or high voltage from the sensor.
P0750
P0755
Overrun clutch solenoid valve OVERRUN CLUTCH S/V O/R CLUCH SOL/ CIRC
P1760
T/C clutch solenoid valve T/C CLUTCH SOL/V TCC SOLENOID/ CIRC
P0740
Line pressure solenoid valve LINE PRESSURE S/V L/PRESS SOL/ CIRC
P0745
Throttle position sensor, Throttle position switch THROTTLE POSI SEN Engine speed signal ENGINE SPEED SIG A/T fluid temperature sensor BATT/FLUID TEMP SEN TCM (RAM) CONTROL UNIT (RAM) TCM (ROM) CONTROL UNIT (ROM) ATF TEMP SEN/ CIRC TP SEN/CIRC A/T
P1705
TCM does not receive the proper voltage signal from the ECM. TCM receives an excessively low or high voltage from the sensor.
P0725
P0710
TCM memory (RAM) is malfunctioning.
TCM memory (ROM) is malfunctioning.
AT-42

CONSULT-II (Contd)
TCM self-diagnosis Detected items (Screen terms for CONSULT-II, SELF DIAGNOSIS test mode) Malfunction is detected when ... Available by O/D OFF indicator lamp or A/T on CONSULT-II Available by malfunction indicator lamp*2, ENGINE on CONSULT-II or GST OBD-II (DTC)
GI MA EM LC EC
X
A/T
ENGINE TCM memory (EEP ROM) is malfunctioning. This is not a malfunction message (Whenever shutting off a power supply to the TCM, this message appears on the screen.) No failure has been detected.
TCM (EEP ROM) CONT UNIT (EEP ROM) Initial start INITIAL START
FE
X X
No failure (NO SELF DIAGNOSTIC FAILURE INDICATED FURTHER TESTING MAY BE REQUIRED**)
CL MT
X: Applicable : Not applicable *1: These malfunctions cannot be displayed by MIL *2: Refer to EC-81, Malfunction Indicator Lamp (MIL).
if another malfunction is assigned to MIL.
DATA MONITOR MODE (A/T)

Monitor item Item Display TCM input signals Main signals Description Remarks
NCAT0022S04
Vehicle speed sensor 1 (A/T) (Revolution sensor)
VHCL/S SEA/T [km/h] or [mph] X
Vehicle speed computed When racing engine in N from signal of revolution or P position with vehicle sensor is displayed. stationary, CONSULT-II data may not indicate 0 km/h (0 mph). Vehicle speed computed from signal of vehicle speed sensor is displayed. Vehicle speed display may not be accurate under approx. 10 km/h (6 mph). It may not indicate 0 km/h (0 mph) when vehicle is stationary.
Vehicle speed sensor 2 (Meter)
VHCL/S SEMTR [km/h] or [mph] X
Throttle position sensor
THRTL POS SEN [V] FLUID TEMP SE [V]
Throttle position sensor signal voltage is displayed. A/T fluid temperature sensor signal voltage is displayed. Signal voltage lowers as fluid temperature rises. Source voltage of TCM is displayed. Engine speed, computed Engine speed display may from engine speed not be accurate under signal, is displayed. approx. 800 rpm. It may not indicate 0 rpm even when engine is not running.
A/T fluid temperature sensor
Battery voltage Engine speed
BATTERY VOLT [V] ENGINE SPEED [rpm]
AT-43

CONSULT-II (Contd)
Monitor item Item Display TCM input signals X Main signals Description Remarks
Overdrive control switch
OVERDRIVE SW [ON/OFF] PN POSI SW [ON/OFF] R POSITION SW [ON/OFF] D POSITION SW [ON/OFF] 2 POSITION SW [ON/OFF]
ON/OFF state computed from signal of overdrive control SW is displayed. ON/OFF state computed from signal of PN position SW is displayed. ON/OFF state computed from signal of R position SW is displayed. ON/OFF state computed from signal of D position SW is displayed. ON/OFF status, computed from signal of 2 position SW, is displayed. ON/OFF status, computed from signal of 1 position SW, is displayed. Status of ASCD cruise signal is displayed. ON ... Cruising state OFF ... Normal running state This is displayed even when no ASCD is mounted.
PN position switch
R position switch
D position switch
2 position switch
1 position switch
1 POSITION SW [ON/OFF]
ASCD cruise signal
ASCDCRUISE [ON/OFF] X
ASCD OD cut signal
ASCDOD CUT [ON/OFF] X
Status of ASCD OD This is displayed even release signal is diswhen no ASCD is played. mounted. ON ... OD released OFF ... OD not released ON/OFF status, computed from signal of kickdown SW, is displayed. ON/OFF status, computed from signal of closed throttle position SW, is displayed. ON/OFF status, computed from signal of wide open throttle position SW, is displayed. Gear position data used for computation by TCM, is displayed. Selector lever position data, used for computation by TCM, is displayed. Vehicle speed data, used for computation by TCM, is displayed. A specific value used for control is displayed if fail-safe is activated due to error. This is displayed even when no kickdown switch is equipped.
Kickdown switch
KICKDOWN SW [ON/OFF]
Closed throttle position switch
CLOSED THL/SW [ON/OFF]
Wide open throttle position W/O THRL/P-SW switch [ON/OFF]
Gear position
GEAR X
Selector lever position
SLCT LVR POSI X
Vehicle speed
VEHICLE SPEED [km/h] or [mph]
AT-44

CONSULT-II (Contd)
Monitor item Item Display TCM input signals Main signals Description Remarks
GI MA EM
Stop lamp switch
BRAKE SW [ON/OFF] X
ON/OFF status are displayed. ON: Brake pedal is depressed. OFF: Brake pedal is released. Throttle position data, used for computation by TCM, is displayed. Control value of line pressure solenoid valve, computed by TCM from each input signal, is displayed. Control value of torque converter clutch solenoid valve, computed by TCM from each input signal, is displayed. Control value of shift solenoid valve A, computed by TCM from each input signal, is displayed. Control value of shift solenoid valve B, computed by TCM from each input signal, is displayed. Control value of overrun clutch solenoid valve computed by TCM from each input signal is displayed. Control status of O/D OFF indicator lamp is displayed. Control value of solenoid is displayed even if solenoid circuit is disconnected. The OFF signal is displayed if solenoid circuit is shorted. A specific value used for control is displayed if fail-safe is activated due to error.
Throttle position
THROTTLE POSI [/8] LINE PRES DTY [%]
LC EC FE CL MT
Line pressure duty
Torque converter clutch solenoid valve duty
TCC S/V DUTY [%] X
Shift solenoid valve A
SHIFT S/V A [ON/OFF] X
Shift solenoid valve B
SHIFT S/V B [ON/OFF] X
Overrun clutch solenoid valve
OVERRUN/C S/V [ON/OFF] X
Self-diagnosis display lamp SELF-D DP LMP (O/D OFF indicator lamp) [ON/OFF] X: Applicable : Not applicable
DTC WORK SUPPORT MODE WITH CONSULT-II CONSULT-II Setting Procedure

1. 2.
NCAT0022S05 NCAT0022S0501
SC EL IDX
Turn ignition switch OFF. Connect CONSULT-II to Data link connector which is located in left side lower dash panel.
SAT845J
AT-45

CONSULT-II (Contd)
3. 4.
Turn ignition switch ON. Touch START.
SAT586J
5.
Touch A/T.
SAT014K
6.
Touch DTC WORK SUPPORT.
SAT971J
7.
Touch select item menu (1ST, 2ND, etc.).
SAT018K
8.
Touch START.
SAT589J
AT-46

CONSULT-II (Contd)
9.
Perform driving test according to DTC CONFIRMATION PROCEDURE in TROUBLE DIAGNOSIS FOR DTC.
GI MA EM
SAT019K
LC
When testing conditions are satisfied, CONSULT-II screen changes from OUT OF CONDITION to TESTING.
EC FE CL
SAT591J
MT
10. Stop vehicle. If NG appears on the screen, malfunction may exist. Go to DIAGNOSTIC PROCEDURE.
AX SU BR
SAT592J
ST RS BT HA
SAT593J
11. Perform test drive to check gear shift feeling in accordance with instructions displayed.
SC EL IDX
SAT594J
AT-47

CONSULT-II (Contd)
12. Touch YES or NO.
SAT595J
13. CONSULT-II procedure ended. If NG appears on the screen, a malfunction may exist. Go to DIAGNOSTIC PROCEDURE.
SAT596J
SAT593J
DTC WORK SUPPORT MODE

DTC work support item Description Following items for A/T 1st gear function (P0731) can be confirmed. Self-diagnosis status (whether the diagnosis is being conducted or not) Self-diagnosis result (OK or NG) Following items for A/T 2nd gear function (P0732) can be confirmed. Self-diagnosis status (whether the diagnosis is being conducted or not) Self-diagnosis result (OK or NG) Following items for A/T 3rd gear function (P0733) can be confirmed. Self-diagnosis status (whether the diagnosis is being conducted or not) Self-diagnosis result (OK or NG)
NCAT0022S06
Check items (Possible cause) Shift solenoid valve A Shift solenoid valve B Each clutch Hydraulic control circuit
1ST GR FNCTN P0731
2ND GR FNCTN P0732
Shift solenoid valve B Each clutch Hydraulic control circuit
3RD GR FNCTN P0733
Shift solenoid valve A Each clutch Hydraulic control circuit
AT-48

CONSULT-II (Contd)
DTC work support item Description Following items for A/T 4th gear function (P0734) can be confirmed. Self-diagnosis status (whether the diagnosis is being conducted or not) Self-diagnosis result (OK or NG) Following items for A/T TCC S/V function (lock-up) (P0744) can be confirmed. Self-diagnosis status (whether the diagnosis is being conducted or not) Self-diagnosis result (OK or NG) Check items (Possible cause) Shift solenoid valve A Shift solenoid valve B Overrun clutch solenoid valve Line pressure solenoid valve Each clutch Hydraulic control circuit
GI MA EM LC
4TH GR FNCTN P0734
TCC S/V FNCTN P0744
Torque converter clutch solenoid valve Each clutch Hydraulic control circuit
DIAGNOSTIC PROCEDURE WITHOUT CONSULT-II NCAT0022S07 EC OBD-II Self-diagnostic Procedure (With GST) NCAT0022S0701
Refer to EC-101, section Generic Scan Tool (GST).
FE CL MT
OBD-II Self-diagnostic Procedure (No Tools)

Refer to EC-81, Malfunction Indicator Lamp (MIL).
NCAT0022S0702
AX SU BR
TCM Self-diagnostic Procedure (No Tools)
NCAT0022S0703
SAT491J
Preparation 1. Turn ignition switch to OFF position. 2. Connect the handy type vacuum pump to the throttle opener and apply vacuum 25.3 kPa (190 mmHg, 7.48 inHg). 3. Disconnect the throttle position switch harness connector. 4. Turn ignition switch to ON position. 5. Check continuity of the closed throttle position switch. Continuity should exist. (If continuity does not exist, check throttle opener and closed throttle position switch. Then increase vacuum until closed throttle position switch shows continuity.) 6. Go to TCM self-diagnostic procedure (No tools).
SAT851J
AT-49

CONSULT-II (Contd)
CHECK O/D OFF INDICATOR LAMP
1. Move selector lever in P position. Start the engine. Warm engine to normal operating temperature. 2. Turn ignition switch to OFF position. 3. Wait 5 seconds.
SAT967I
4. Turn ignition switch to ON position. (Do not start engine.) 5. Does O/D OFF indicator lamp come on for about 2 seconds?
SAT490J
Yes or No Yes No GO TO 2. Go to 1. O/D OFF Indicator Lamp Does Not Come On, AT-225.
AT-50

CONSULT-II (Contd)
2
1. 2. 3. 4.
JUDGEMENT PROCEDURE STEP 1
Turn ignition switch to OFF position. Turn ignition switch to ACC position. Move selector lever from P to D position. Turn ignition switch to ON position. (Do not start engine.) 5. Depress and hold overdrive control switch in OFF position (the O/D OFF indicator lamp will be ON) until directed to release the switch. (If O/D OFF indicator lamp does not come on, go to step on AT-263.) 6. Turn ignition switch to OFF position.
SAT968I
7. Turn ignition switch to ON position. (Do not start engine.) 8. Release the overdrive control switch (the O/D OFF indicator lamp will be OFF). 9. Wait 2 seconds. 10. Move the selector lever to 2 position. 11. Depress and release the overdrive control switch (the O/D OFF indicator lamp will be ON). 12. Depress and hold the overdrive control switch (the O/D OFF indicator lamp will be OFF) until directed to release the switch.
MT
AX SU BR ST RS
SAT969I
GO TO 3.
BT HA SC EL IDX
AT-51

CONSULT-II (Contd)
3
1. 2. 3. 4. 5.
JUDGEMENT PROCEDURE STEP 2

Move selector lever to 1 position. Release the overdrive control switch. Depress and release the overdrive control switch (the O/D OFF indicator lamp will be ON). Depress and release the overdrive control switch (the O/D OFF indicator lamp will be OFF). Depress and hold the overdrive control switch (the O/D OFF indicator lamp will be ON) until directed to release the switch.
SAT970I
6. Depress accelerator pedal fully and release.
SAT981F
7. Release the overdrive control switch (the O/D OFF indicator lamp will begin to flash ON and OFF). GO TO 4.
CHECK SELF-DIAGNOSIS CODE
Check O/D OFF indicator lamp. Refer to JUDGEMENT OF SELF-DIAGNOSIS CODE, AT-53.
SAT490J
DIAGNOSIS END
AT-52

CONSULT-II (Contd)
Judgement of Self-diagnosis Code

O/D OFF indicator lamp: All judgement flickers are the same. 1st judgement flicker is longer than others.
NCAT0022S0704
GI MA EM LC
SAT437F
EC FE CL MT
SAT436F
All circuits that can be confirmed by self-diagnosis are OK. 2nd judgement flicker is longer than others.
Revolution sensor circuit is short-circuited or disconnected. Go to VEHICLE SPEED SENSORA/T (REVOLUTION SENSOR), AT-119. 3rd judgement flicker is longer than others.
AX
SAT439F SAT441F
Vehicle speed sensor circuit is short-circuited or disconnected. Go to VEHICLE SPEED SENSORMTR, AT-215. 4th judgement flicker is longer than others.
Throttle position sensor circuit is short-circuited or disconnected. Go to THROTTLE POSITION SENSOR, AT-193. 5th judgement flicker is longer than others.
SU BR ST RS
SAT445F
BT HA SC EL IDX
Shift solenoid valve B circuit is short-circuited or disconnected. SAT443F Go to SHIFT SOLENOID VALVE B, AT-187. Shift solenoid valve A circuit is short-circuited or disconnected. Go to SHIFT SOLENOID VALVE A, AT-181.
AT-53

CONSULT-II (Contd)
O/D OFF indicator lamp: 6th judgement flicker is longer than others. 7th judgement flicker is longer than others.
SAT447F
SAT449F
Overrun clutch solenoid valve circuit is short-circuited or discon- Torque converter clutch solenoid valve circuit is short-circuited or disconnected. nected. Go to TORQUE CONVERTER CLUTCH SOLENOID Go to OVERRUN CLUTCH SOLENOID VALVE, AT-202. VALVE, AT-157. 8th judgement flicker is longer than others. 9th judgement flicker is longer than others.
SAT453F
Engine speed signal circuit is short-circuited or disconnected. SAT451F Go to ENGINE SPEED SIGNAL, AT-124. A/T fluid temperature sensor is disconnected or TCM power source circuit is damaged. Go to A/T FLUID TEMPERATURE SENSOR AND TCM POWER SOURCE, AT-113. 10th judgement flicker is longer than others. Flickers as shown below.
SAT457F SAT455F
Line pressure solenoid valve circuit is short-circuited or disconnected. Go to LINE PRESSURE SOLENOID VALVE, AT-174.
Battery power is low. Battery has been disconnected for a long time. Battery is connected conversely. (When reconnecting TCM connectors. This is not a problem.)
AT-54

CONSULT-II (Contd)
O/D OFF indicator lamp: Lamp comes on.
GI MA EM LC
SAT367J
EC FE CL MT
PNP switch, overdrive control switch or throttle position switch circuit is disconnected or TCM is damaged. Go to 21. TCM Self-diagnosis Does Not Activate (PNP, OVERDRIVE CONTROL AND THROTTLE POSITION SWITCHES), AT-263. t1 = 2.5 seconds t2 = 2.0 seconds t3 = 1.0 second t4 = 1.0 second
AT-55
TROUBLE DIAGNOSIS INTRODUCTION

Introduction
Introduction
NCAT0023
SAT631IA
SAT632I
The TCM receives a signal from the vehicle speed sensor, throttle position sensor or PNP switch and provides shift control or lock-up control via A/T solenoid valves. The TCM also communicates with the ECM by means of a signal sent from sensing elements used with the OBD-related parts of the A/T system for malfunction-diagnostic purposes. The TCM is capable of diagnosing malfunctioning parts while the ECM can store malfunctions in its memory. Input and output signals must always be correct and stable in the operation of the A/T system. The A/T system must be in good operating condition and be free of valve seizure, solenoid valve malfunction, etc. It is much more difficult to diagnose a problem that occurs intermittently rather than continuously. Most intermittent problems are caused by poor electric connections or improper wiring. In this case, careful checking of suspected circuits may help prevent the replacement of good parts. A visual check only, may not find the cause of the problems. A road test with CONSULT-II (or GST) or a circuit tester connected should be performed. Follow the Work Flow. Refer to AT-60. Before undertaking actual checks, take a few minutes to talk with a customer who approaches with a driveability complaint. The customer can supply good information about such problems, especially intermittent ones. Find out what symptoms are present and under what conditions they occur. A Diagnostic Worksheet like the example (AT-58) should be used. Start your diagnosis by looking for conventional problems first. This will help troubleshoot driveability problems on an electronically controlled engine vehicle. Also check related Service bulletins for information.
SEF234G
AT-56

Introduction (Contd)
DIAGNOSTIC WORKSHEET Information from Customer

KEY POINTS WHAT ..... Vehicle & A/T model WHEN..... Date, Frequencies WHERE..... Road conditions HOW..... Operating conditions, Symptoms
Customer name Trans. model Incident Date Frequency Symptoms MR/MS Model & Year Engine Manuf. Date Continuous Intermittent ( VIN Mileage In Service Date times a day) Particular position) 3rd , O/D)
=NCAT0023S01 NCAT0023S0101
Vehicle does not move. No up-shift
( Any position 2nd , 3rd
( 1st , 2nd
No down-shift
( O/D , 3rd
3rd , 2nd 2nd , 1st)
Lockup malfunction Shift point too high or too low. Shift shock or slip Noise or vibration No kickdown No pattern select Others ( O/D OFF indicator lamp Blinks for about 8 seconds. Continuously lit Malfunction indicator lamp (MIL) Continuously lit Not lit Not lit ) ( N , D Lockup Any drive position)
MT
AT-57

Diagnostic Worksheet
1. 2. Read the Fail-safe and listen to customer complaints. CHECK A/T FLUID Leakage (Follow specified procedure) Fluid condition Fluid level 3. Perform STALL TEST and LINE PRESSURE TEST. Stall test Mark possible damaged components/others. Torque converter one-way clutch Reverse clutch Forward clutch Overrun clutch Forward one-way clutch Low & reverse brake Low one-way clutch Engine Line pressure is low Clutches and brakes except high clutch and brake band are OK AT-8
=NCAT0023S0102
AT-62
AT-62, 66
Line Pressure test Suspected parts: 4. Perform all ROAD TEST and mark required procedures. 4-1. Check before engine is started. SELF-DIAGNOSTIC PROCEDURE Mark detected items. PNP switch, AT-107. A/T fluid temperature sensor, AT-113. Vehicle speed sensorA/T (Revolution sensor), AT-119. Engine speed signal, AT-124. Torque converter clutch solenoid valve, AT-157. Line pressure solenoid valve, AT-174. Shift solenoid valve A, AT-181. Shift solenoid valve B, AT-187. Throttle position sensor, AT-193. Overrun clutch solenoid valve, AT-202. PNP, overdrive control and throttle position switches, AT-263. A/T fluid temperature sensor and TCM power source, AT-208. Vehicle speed sensorMTR, AT-215. Control unit (RAM), control unit (ROM), AT-219. Control unit (EEP ROM), AT-221. Battery Others 4-2. Check at idle 1. 2. 3. 4. 5. 6. 7. O/D OFF Indicator Lamp Does Not Come On, AT-225. Engine Cannot Be Started In P And N Position, AT-228. In P Position, Vehicle Moves Forward Or Backward When Pushed, AT-229. In N Position, Vehicle Moves, AT-230. Large Shock. N , R Position, AT-232. Vehicle Does Not Creep Backward In R Position, AT-234. Vehicle Does Not Creep Forward In D, 2 Or 1 Position, AT-237. AT-69 AT-67 AT-68
AT-58

4. 4-3. Cruise test Part-1 8. Vehicle Cannot Be Started From D1, AT-240. 9. A/T Does Not Shift: D1 , D2 Or Does Not Kickdown: D4 , D2, AT-243. 10. A/T Does Not Shift: D2 , D3, AT-246. 11. A/T Does Not Shift: D3 , D4, AT-249. 12. A/T Does Not Perform Lock-up, AT-252. 13. A/T Does Not Hold Lock-up Condition, AT-254. 14. Lock-up Is Not Released, AT-256. 15. Engine Speed Does Not Return To Idle (Light Braking D4 , D3), AT-257. AT-80 AT-72 AT-76
GI MA EM LC EC
Part-2 16. Vehicle Does Not Start From D1, AT-259. 9. A/T Does Not Shift: D1 , D2 Or Does Not Kickdown: D4 , D2, AT-243. 10. A/T Does Not Shift: D2 , D3, AT-246. 11. A/T Does Not Shift: D3 , D4, AT-249.
Part-3 17. A/T Does Not Shift: D4 , D3 When Overdrive Control Switch ON , OFF, AT-260 15. Engine Speed Does Not Return To Idle (Engine Brake In D3), AT-257. 18. A/T Does Not Shift: D3 , 22, When Selector Lever D , 2 Position, AT-261. 15. Engine Speed Does Not Return To Idle (Engine Brake In 22), AT-257. 19. A/T Does Not Shift: 22 , 11, When Selector Lever 2 , 1 Position, AT-262. 20. Vehicle Does Not Decelerate By Engine Brake, AT-263. SELF-DIAGNOSTIC PROCEDURE Mark detected items. PNP switch, AT-107. A/T fluid temperature sensor, AT-113. Vehicle speed sensorA/T (Revolution sensor), AT-119. Engine speed signal, AT-124. Torque converter clutch solenoid valve, AT-157. Line pressure solenoid valve, AT-174. Shift solenoid valve A, AT-181. Shift solenoid valve B, AT-187. Throttle position sensor, AT-193. Overrun clutch solenoid valve, AT-202. PNP, overdrive control and throttle position switches, AT-263. A/T fluid temperature sensor and TCM power source, AT-208. Vehicle speed sensorMTR, AT-215. Control unit (RAM), control unit (ROM), AT-219. Control unit (EEP ROM), AT-221. Battery Others 5. 6. 7. For self-diagnosis NG items, inspect each component. Repair or replace the damaged parts. Perform all ROAD TEST and re-mark required procedures.
AT-82
FE CL MT
AX SU BR ST RS
AT-41 AT-67
BT HA SC EL IDX
Perform DTC CONFIRMATION PROCEDURE for following MIL indicating items and check out NG items. EC section Refer to EC-68, Emission-related Diagnostic Information. DTC DTC DTC DTC DTC (P0731) A/T 1st gear function, AT-128. (P0732) A/T 2nd gear function, AT-135. (P0733) A/T 3rd gear function, AT-141. (P0734) A/T 4th gear function, AT-147. (P0744) A/T TCC S/V function (lock-up), AT-163. AT-99 AT-86
8.
Perform the Diagnostic Procedures for all remaining items marked NG. Repair or replace the damaged parts. Refer to the Symptom Chart when you perform the procedures. (The chart also shows some other possible symptoms and the component inspection orders.) Erase DTC from TCM and ECM memories.
9.
AT-38
AT-59

Work Flow
Work Flow
HOW TO PERFORM TROUBLE DIAGNOSES FOR QUICK AND ACCURATE REPAIR
A good understanding of the malfunction conditions can make troubleshooting faster and more accurate. In general, each customer feels differently about a problem. It is important to fully understand the symptoms or conditions for a customer complaint. Make good use of the two sheets provided, INFORMATION FROM CUSTOMER (AT-57) and DIAGNOSTIC WORKSHEET (AT-58), to perform the best troubleshooting possible.
AT-60

Work Flow (Contd)
WORK FLOW CHART
NCAT0024S02
AX SU BR ST RS BT HA SC EL
SAT930J
*1: *2: *3: *4: *5: *6:
AT-57 AT-58 AT-8 AT-62 AT-62, 66 AT-67
*7: *8: *9: *10: *11: *12:
AT-40 AT-36 AT-53 AT-107 AT-221 AT-225
*13: *14: *15: *16: *17: *18:
AT-263 AT-86 AT-38 AT-108 AT-221 EC-68
IDX
AT-61
TROUBLE DIAGNOSIS BASIC INSPECTION

A/T Fluid Check
A/T Fluid Check

FLUID LEAKAGE CHECK
1. 2. 3.
Clean area suspected of leaking. for example, mating surface of converter housing and transmission case. Start engine, apply foot brake, place selector lever in D position and wait a few minutes. Stop engine.
SAT767B
4.
Check for fresh leakage.
SAT288G
FLUID CONDITION CHECK

Fluid color Dark or black with burned odor Milky pink Varnished fluid, light to dark brown and tacky Suspected problem Wear of frictional material
NCAT0025S02
Water contamination Road water entering through filler tube or breather Oxidation Over or under filling, Overheating
SAT638A
FLUID LEVEL CHECK

Refer to MA-23, Checking A/T Fluid.
NCAT0025S03
Stall Test
STALL TEST PROCEDURE
1. 2.
Check A/T fluid and engine oil levels. If necessary, add. Drive vehicle for approx. 10 minutes or until fluid and oil reach operating temperature. ATF operating temperature: 50 - 80C (122 - 176F)
SAT647B
AT-62

Stall Test (Contd)
3. 4.
Set parking brake and block wheels. Install a tachometer where it can be seen by driver during test. It is good practice to mark the point of specified engine rpm on indicator.
GI MA EM
SAT513G
LC
5. 6. 7. Start engine, apply foot brake, and place selector lever in D position. Accelerate to wide open throttle gradually while applying foot brake. Quickly note the engine stall revolution and immediately release throttle. During test, never hold throttle wide open for more than 5 seconds. Stall revolution: 2,350 - 2,850 rpm Move selector lever to N position. Cool off ATF. Run engine at idle for at least one minute. Repeat steps 5 through 9 with selector lever in 2, 1 and R positions.
EC FE CL MT
SAT514G
8. 9. 10.
AX SU BR
SAT771B
JUDGEMENT OF STALL TEST
NCAT0026S02
The test result and possible damaged components relating to each result are shown in the illustrations on next page. In order to pinpoint the possible damaged components, follow the WORK FLOW shown in AT-60. NOTE: Stall revolution is too high in D, 2 or 1 position: Slippage occurs in 1st gear but not in 2nd and 3rd gears. ..... Low one-way clutch slippage Slippage occurs in the following gears: 1st through 3rd gears in D position and engine brake functions with overdrive control switch set to OFF. 1st and 2nd gears in 2 position and engine brake functions with accelerator pedal released (fully closed throttle). ..... Forward clutch or forward one-way clutch slippage Stall revolution is too high in R position: Engine brake does not function in 1 position. ..... Low & reverse brake slippage Engine brake functions in 1 position. ..... Reverse clutch slippage Stall revolution within specifications: Vehicle does not achieve speed of more than 80 km/h (50
AT-63

Stall Test (Contd)
MPH). ..... One-way clutch seizure in torque converter housing CAUTION: Be careful since automatic fluid temperature increases abnormally. Slippage occurs in 3rd and 4th gears in D position. ..... High clutch slippage Slippage occurs in 2nd and 4th gear in D position. ..... Brake band slippage Engine brake does not function in 2nd and 3rd gears in D position, 2nd gear in 2 position, and 1st gear in 1 position with overdrive control switch set to OFF. Stall revolution less than specifications: Poor acceleration during starts. ..... One-way clutch seizure in torque converter
AT-64

Stall Test (Contd)
SAT895H
AT-65

Line Pressure Test
Line Pressure Test

LINE PRESSURE TEST PORTS
Location of line pressure test ports are shown in the illustration. Always replace pressure plugs as they are self-sealing bolts.
SAT561J
LINE PRESSURE TEST PROCEDURE

1. 2.
NCAT0027S02
Check A/T fluid and engine oil levels. If necessary, add fluid or oil. Drive vehicle for approx. 10 minutes or until engine oil and ATF reach operating temperature. ATF operating temperature: 50 - 80C (122 - 176F)
SAT647B
3.
Install pressure gauge to corresponding line pressure port.
AAT898
4.
Set parking brake and block wheels. Continue to depress brake pedal fully while line pressure test is being performed at stall speed.
SAT513G
5.
Start engine and measure line pressure at idle and stall speed. When measuring line pressure at stall speed, follow the stall test procedure. Line pressure: Refer to SDS, AT-389.
SAT493G
AT-66

Line Pressure Test (Contd)
JUDGEMENT OF LINE PRESSURE TEST

Judgement Line pressure is low in all positions. Suspected parts
NCAT0027S03
Oil pump wear Control piston damage Pressure regulator valve or plug sticking Spring for pressure regulator valve damaged Fluid pressure leakage between oil strainer and pressure regulator valve Clogged strainer
Line pressure is low in particular position. At idle
Fluid pressure leakage between manual valve and particular clutch For example, line pressure is: Low in R and 1 positions, but Normal in D and 2 positions. Therefore, fluid leakage exists at or around low and reverse brake circuit. Refer to CLUTCH AND BAND CHART, AT-20. Maladjustment of throttle position sensor A/T fluid temperature sensor damaged Line pressure solenoid valve sticking Short circuit of line pressure solenoid valve circuit Pressure modifier valve sticking Pressure regulator valve or plug sticking Open in dropping resistor circuit Maladjustment of throttle position sensor Line pressure solenoid valve sticking Short circuit of line pressure solenoid valve circuit Pressure regulator valve or plug sticking Pressure modifier valve sticking Pilot valve sticking
Line pressure is high.
Line pressure is low. At stall speed
AX SU BR
Road Test
DESCRIPTION
1. 2. 3.
SAT786A
ST RS BT HA
The purpose of the test is to determine overall performance of A/T and analyze causes of problems. The road test consists of the following three parts: Check before engine is started Check at idle Cruise test
Before road test, familiarize yourself with all test procedures and items to check. Conduct tests on all items until specified symptom is found. Troubleshoot items which check out No Good after road test. Refer to ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION and TROUBLE DIAGNOSES FOR SYMPTOMS, AT-36 - AT-53 and AT-225 - AT-263.
SC EL IDX
SAT496G
AT-67

Road Test (Contd)
1. CHECK BEFORE ENGINE IS STARTED

1 CHECK O/D OFF INDICATOR LAMP
1. Park vehicle on flat surface. 2. Move selector lever to P position.
=NCAT0028S02
SAT967I
3. Turn ignition switch to OFF position. Wait at least 5 seconds. 4. Turn ignition switch to ON position. (Do not start engine.) 5. Does O/D OFF indicator lamp come on for about 2 seconds?
SAT490J
Yes or No Yes No GO TO 2. Stop ROAD TEST. Go to 1. O/D OFF Indicator Lamp Does Not Come On, AT-225.
CHECK O/D OFF INDICATOR LAMP
Does O/D OFF indicator lamp flicker for about 8 seconds?
SAT490J
Yes or No Yes No Perform self-diagnosis and check NG items on the DIAGNOSTIC WORKSHEET, AT-58. Refer to TCM SELF-DIAGNOSIS PROCEDURE (NO TOOLS), AT-49. 1. Turn ignition switch to OFF position. 2. Perform self-diagnosis and note NG items. Refer to TCM SELF-DIAGNOSIS PROCEDURE (NO TOOLS), AT-49. 3. Go to 2. CHECK AT IDLE, AT-69.
AT-68

Road Test (Contd)
2. CHECK AT IDLE
1 CHECK ENGINE START
1. Park vehicle on flat surface. 2. Move selector lever to P position.
=NCAT0028S03
GI MA EM LC EC
SAT769B
3. Turn ignition switch to OFF position. 4. Turn ignition switch to START position. 5. Is engine started? Yes or No Yes No GO TO 2. Mark the box on the DIAGNOSTIC WORKSHEET. Go to 2. Engine Cannot Be Started In P and N Position, AT-228. Continue ROAD TEST.
FE CL MT
CHECK ENGINE START
1. Turn ignition switch to ACC position. 2. Move selector lever to D, 1, 2 or R position.
AX SU BR ST
SAT770B
RS BT HA SC EL IDX
3. Turn ignition switch to START position. 4. Is engine started? Yes or No Yes No Mark the box on the DIAGNOSTIC WORKSHEET. Go to 2. Engine Cannot Be Started In P and N Position, AT-228. Continue ROAD TEST. GO TO 3.
AT-69

Road Test (Contd)
CHECK VEHICLE MOVE
1. Move selector lever to P position.
SAT768B
2. Turn ignition switch to OFF position. 3. Release parking brake. GO TO 4.
CHECK VEHICLE MOVE
1. Push vehicle forward or backward. 2. Does vehicle move when it is pushed forward or backward?
SAT796A
3. Apply parking brake. Yes or No Yes No Mark the box on the DIAGNOSTIC WORKSHEET. Go to 3. In P Position, Vehicle Moves Forward Or Backward When Pushed, AT-229. Continue ROAD TEST. GO TO 5.
AT-70

Road Test (Contd)
CHECK VEHICLE MOVE
1. Start engine. 2. Move selector lever to N position.
GI MA EM LC
SAT771B
EC FE
3. Release parking brake. 4. Does vehicle move forward or backward? Yes or No Yes No Mark the box on the DIAGNOSTIC WORKSHEET. Go to 4. In N Position, Vehicle Moves, AT-230. Continue ROAD TEST. GO TO 6.
CL MT
CHECK SHIFT SHOCK
1. Apply foot brake.
AX SU BR
SAT797A
2. Move selector lever to R position.
ST RS BT HA
SAT772B
SC EL IDX
3. Is there large shock when changing from N to R position? Yes or No Yes No Mark the box on the DIAGNOSTIC WORKSHEET. Go to 5. Large Shock N , R Position, AT-232. Continue ROAD TEST. GO TO 7.
AT-71

Road Test (Contd)
CHECK VEHICLE MOVE
1. Release foot brake for several seconds.
SAT799A
2. Does vehicle creep backward when foot brake is released? Yes or No Yes No GO TO 8. Mark the box on the DIAGNOSTIC WORKSHEET. Go to 6. Vehicle Does Not Creep Backward In R Position, AT-234. Continue ROAD TEST.
CHECK VEHICLE MOVE
1. Move selector lever to D, 2 and 1 positions and check if vehicle creeps forward.
SAT773B
2. Does vehicle creep forward in all three positions? Yes or No Yes No Go to 3. CRUISE TEST, AT-72. Mark the box on the DIAGNOSTIC WORKSHEET. Go to 7. Vehicle Does Not Creep Forward In D, 2 Or 1 Position, AT-237. Continue ROAD TEST.
3. CRUISE TEST
Check all items listed in Parts 1 through 3.
NCAT0028S04
With CONSULT-II
NCAT0028S0401
Using CONSULT-II, conduct a cruise test and record the result. Print the result and ensure that shifts and lock-ups take place as per Shift Schedule.
SAT601J
AT-72

Road Test (Contd)
CONSULT-II Setting Procedure

1. 2.
NCAT0028S0402
Turn ignition switch OFF. Connect CONSULT-II to Data link connector which is located in left side lower dash panel.
GI MA EM
SAT845J
LC
3. 4. Turn ignition switch ON. Touch START.
EC FE CL
SAT586J
MT
5. Touch A/T.
AX SU BR
SAT014K
6.
Touch DATA MONITOR.
ST RS BT HA
SAT971J
7. 8.
Touch MAIN SIGNALS or TCM INPUT SIGNALS. See Numerical Display, Barchart Display or Line Graph Display.
SC EL IDX
SAT175K
AT-73

Road Test (Contd)
9.
Touch SETTING to set recording condition (AUTO TRIG or MANU TRIG) and touch BACK. 10. Touch Start.
SAT973J
11. When performing cruise test, touch RECORD.
SAT134K
12. After finishing cruise test part 1, touch STOP.
SAT135K
13. Touch STORE and touch BACK.
SAT987J
SAT974J
AT-74

Road Test (Contd)
14. 15. 16. 17.
Touch DISPLAY. Touch PRINT. Check the monitor data printed out. Continue cruise test part 2 and 3.
GI MA EM
SAT975J
LC
Without CONSULT-II
NCAT0028S0403
Throttle position sensor can be checked by voltage across terminals 41 and 42 of TCM.
EC FE CL
SAT417J
MT
AT-75

Road Test (Contd)
Cruise Test Part 1

1 CHECK STARTING GEAR (D1) POSITION
1. Drive vehicle for approx. 10 minutes to warm engine oil and ATF up to operating temperature. ATF operating temperature: 50 - 80C (122 - 176F) 2. Park vehicle on flat surface. 3. Set overdrive control switch to ON position. 4. Move selector lever to P position.
=NCAT0028S0404
SAT001J
5. Start engine. 6. Move selector lever to D position.
SAT775B
7. Accelerate vehicle by constantly depressing accelerator pedal halfway.
SAT495G
8. Does vehicle start from D1? Read gear position. Yes or No Yes No GO TO 2. Go to 8. Vehicle Cannot Be Started From D1, AT-240. Continue ROAD TEST.
AT-76

Road Test (Contd)
CHECK SHIFT UP (D1 TO D2)
Does A/T shift from D1 to D2 at the specified speed? Read gear position, throttle opening and vehicle speed. Specified speed when shifting from D1 to D2: Refer to Shift schedule, AT-389.
GI MA EM LC EC
SAT954I
Yes or No Yes No GO TO 3. Go to 9. A/T Does Not Shift: D1 , D2 Or Does Not Kickdown: D4 , D2, AT-243. Continue ROAD TEST.
FE CL MT
Does A/T shift from D2 to D3 at the specified speed? Read gear position, throttle position and vehicle speed. Specified speed when shifting from D2 to D3: Refer to Shift schedule, AT-389.
AX SU BR
SAT955I
Yes or No Yes No GO TO 4. Go to 10. A/T Does Not Shift: D2 , D3, AT-246. Continue ROAD TEST.
AT-77

Road Test (Contd)
SAT956I
CHECK LOCK-UP (D4 TO D4 L/U)
Does A/T perform lock-up at the specified speed? Read vehicle speed, throttle position when lock-up duty becomes 94%. Specified speed when lock-up occurs: Refer to Shift schedule, AT-389.
SAT957I
Yes or No Yes No GO TO 6. Go to 12. A/T Does Not Perform Lock-up, AT-252. Continue ROAD TEST.
CHECK HOLD LOCK-UP
Does A/T hold lock-up condition for more than 30 seconds? Yes or No Yes No GO TO 7. Go to 13. A/T Does Not Hold Lock-up Condition, AT-254.
AT-78

Road Test (Contd)
CHECK SHIFT DOWN (D4 L/U TO D4)
1. Release accelerator pedal. 2. Is lock-up released when accelerator pedal is released?
GI MA EM LC
SAT958I
Yes or No Yes No GO TO 8. Go to 14. Lock-up Is Not Released, AT-256. Continue ROAD TEST.
EC FE CL MT
CHECK SHIFT DOWN (D4 TO D3)
1. Decelerate vehicle by applying foot brake lightly. 2. Does engine speed return to idle smoothly when A/T is shifted from D4 to D3? Read gear position and engine speed.
AX SU
SAT959I
Yes or No Yes No 1. Stop vehicle. 2. Go to Cruise test Part 2, AT-80. Go to 15. Engine Speed Does Not Return To Idle (Light Braking D4 , D3), AT-257. Continue ROAD TEST.
BR ST RS BT HA SC EL IDX
AT-79

Road Test (Contd)
Cruise Test Part 2

1
1. 2. 3. 4.
=NCAT0028S0405
CHECK STARTING GEAR (D1) POSITION

Confirm overdrive control switch is in ON position. Confirm selector lever is in D position. Accelerate vehicle by half throttle again. Does vehicle start from D1? Read gear position.
SAT495G
Yes or No Yes No GO TO 2. Go to 16. Vehicle Does Not Start From D1, AT-259. Continue ROAD TEST.
CHECK SHIFT UP AND SHIFT DOWN (D3 TO D4 TO D2)
1. Accelerate vehicle to 80 km/h (50 MPH) as shown in illustration. 2. Release accelerator pedal and then quickly depress it fully. 3. Does A/T shift from D4 to D2 as soon as accelerator pedal is depressed fully? Read gear position and throttle position.
SAT404H
Yes or No Yes No GO TO 3. Go to 9. A/T Does Not Shift: D1 , D2 Or Does Not Kickdown: D4 , D2, AT-243. Continue ROAD TEST.
AT-80

Road Test (Contd)
GI MA EM LC EC
SAT960I
FE CL MT
CHECK SHIFT UP (D3 TO D4) AND ENGINE BRAKE
Release accelerator pedal after shifting from D2 to D3. Does A/T shift from D3 to D4 and does vehicle decelerate by engine brake? Read gear position, throttle position and vehicle speed.
AX SU BR
SAT405H
Yes or No Yes No 1. Stop vehicle. 2. Go to Cruise test Part 3, AT-82. Go to 11. A/T Does Not Shift: D3 , D4, AT-249. Continue ROAD TEST.
AT-81

Road Test (Contd)
Cruise Test Part 3

1 VEHICLE SPEED D4 POSITION
1. Confirm overdrive control switch is in ON position. 2. Confirm selector lever is in D position. 3. Accelerate vehicle using half-throttle to D4.
=NCAT0028S0406
SAT812A
GO TO 2.
1. Release accelerator pedal.
SAT813A
2. Set overdrive control switch to OFF position while driving in D4. 3. Does A/T shift from D4 to D3 (O/D OFF)? Read gear position and vehicle speed.
SAT999I
Yes or No Yes No GO TO 3. Go to 17. A/T Does Not Shift: D4 , D3, When Overdrive Control Switch ON , OFF, AT-260. Continue ROAD TEST.
AT-82

Road Test (Contd)
CHECK ENGINE BRAKE
Does vehicle decelerate by engine brake?
GI MA EM LC
SAT999I
EC FE CL MT
Yes or No Yes No GO TO 4. Go to 15. Engine Speed Does Not Return To Idle (Light Braking D4 , D3), AT-257. Continue ROAD TEST.
1. Move selector lever from D to 2 position while driving in D3 (O/D OFF). 2. Does A/T shift from D3 (O/D OFF) to 22? Read gear position.
AX SU BR
SAT791GA
Yes or No Yes No GO TO 5. Go to 18. A/T Does Not Shift: D3 , D2, When Selector Lever D , 2 Position, AT-261. Continue ROAD TEST.
AT-83

Road Test (Contd)
CHECK ENGINE BRAKE
SAT791GA
Yes or No Yes No GO TO 6. Go to 15. Engine Speed Does Not Return To Idle (Light Braking D4 , D3), AT-257. Continue ROAD TEST.
CHECK SHIFT DOWN
1. Move selector lever from 2 to 1 position while driving in 22. 2. Does A/T shift from 22 to 11 position? Read gear position.
SAT778B
Yes or No Yes No GO TO 7. Go to 19. A/T Does Not Shift: 22 , 11, When Selector lever 2 , 1 Position, AT-262. Continue ROAD TEST.
AT-84

Road Test (Contd)
CHECK ENGINE BRAKE
GI MA EM LC
SAT778B
EC FE CL MT
Yes or No Yes 1. Stop vehicle. 2. Perform self-diagnosis. Refer to TCM SELF-DIAGNOSTIC PROCEDURE (NO TOOLS), AT-49. Go to 20. Vehicle Does Not Decelerate By Engine Brake, AT-263. Continue ROAD TEST.
No
AT-85
TROUBLE DIAGNOSIS GENERAL DESCRIPTION

Symptom Chart
Symptom Chart
Numbers are arranged in order of inspection. Perform inspections starting with number one and work up. Item Symptom Condition Diagnostic Item
NCAT0029
Reference Page EL-9, POWER SUPPLY ROUTING and SC-10, STARTING SYSTEM AT-281 AT-281 AT-281 AT-281 AT-62 AT-66 EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-119, AT-215 AT-124 AT-308 AT-291 AT-281 AT-286 AT-281 AT-336 AT-327 AT-336 AT-281 AT-66 AT-174 AT-280 AT-327 AT-331 AT-336 AT-336 AT-343
1. Ignition switch and starter Engine cannot start in P and N positions. ON vehicle AT-228 2. Control cable adjustment 3. PNP switch adjustment Engine starts in position other than N and P positions. AT-228 1. Control cable adjustment ON vehicle 2. PNP switch adjustment 1. Fluid level 2. Line pressure test
ON vehicle NOT USED Transaxle noise in P and N positions.
3. Throttle position sensor (Adjustment)
4. Vehicle speed sensorA/T (Revolution sensor) and vehicle speed sensorMTR 5. Engine speed signal 6. Oil pump OFF vehicle 7. Torque converter Vehicle moves when changing into P position, or parking gear does not disengage when shifted out of P position. AT-229 ON vehicle OFF vehicle ON vehicle Vehicle runs in N position. AT-230 1. Control cable adjustment 2. Parking components 1. Control cable adjustment 2. Forward clutch OFF vehicle 3. Reverse clutch 4. Overrun clutch 1. Control cable adjustment 2. Line pressure test ON vehicle 3. Line pressure solenoid valve Vehicle will not run in R position (but runs in D, 2 and 1 positions). Clutch slips. Very poor acceleration. AT-234 OFF vehicle 4. Control valve assembly 5. Reverse clutch 6. High clutch 7. Forward clutch 8. Overrun clutch 9. Low & reverse brake
Slip/Will Not Engage
AT-86

Symptom Chart (Contd)
Item Symptom Condition Diagnostic Item 1. Fluid level 2. Control cable adjustment ON vehicle 3. Line pressure test 4. Line pressure solenoid valve NOT USED Vehicle braked when shifting into R position. 5. Control valve assembly 6. High clutch 7. Brake band OFF vehicle 8. Forward clutch 9. Overrun clutch 1. Engine idling rpm AT-336 AT-336 AT-66 EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-66 AT-113 AT-124 AT-174 AT-280 AT-280 AT-336 AT-281 AT-286 AT-62 AT-66 AT-174 AT-280 AT-280 AT-327 AT-331 AT-336 AT-347 AT-286 Reference Page AT-62 AT-281 AT-66 AT-174 AT-280 AT-331 AT-356
Shift Shock
Sharp shock in shifting from N to D position.
ON vehicle
3. Line pressure test 4. A/T fluid temperature sensor 5. Engine speed signal 6. Line pressure solenoid valve 7. Control valve assembly 8. Accumulator N-D
OFF vehicle Vehicle will not run in D and 2 positions (but runs in 1 and R positions). ON vehicle OFF vehicle
9. Forward clutch 1. Control cable adjustment 2. Low one-way clutch 1. Fluid level 2. Line pressure test
ON vehicle Slips/Will Not Engage Vehicle will not run in D, 1, 2 positions (but runs in R position). Clutch slips. Very poor acceleration. AT-237 OFF vehicle
3. Line pressure solenoid valve 4. Control valve assembly 5. Accumulator N-D 6. Reverse clutch 7. High clutch 8. Forward clutch 9. Forward one-way clutch 10. Low one-way clutch
AT-87

Item Symptom Condition Diagnostic Item 1. Fluid level 2. Control cable adjustment Reference Page AT-62 AT-281 EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-66 AT-174 AT-280 AT-280 AT-336 AT-327 AT-343 AT-308 AT-291 EC-53, Idle Speed/Ignition Timing/Idle Mixture Ratio Adjustment AT-62 AT-66 AT-280 AT-336 AT-308 AT-291
3. Throttle position sensor (Adjustment) ON vehicle 4. Line pressure test Slips/Will Not Engage Clutches or brakes slip somewhat in starting. 5. Line pressure solenoid valve 6. Control valve assembly 7. Accumulator N-D 8. Forward clutch 9. Reverse clutch OFF vehicle 10. Low & reverse brake 11. Oil pump 12. Torque converter
NOT USED
Excessive creep.
ON vehicle
1. Engine idling rpm
1. Fluid level ON vehicle Slips/Will Not Engage No creep at all. AT-234, 237 OFF vehicle 2. Line pressure test 3. Control valve assembly 4. Forward clutch 5. Oil pump 6. Torque converter
AT-88

Item Symptom Condition Diagnostic Item 1. PNP switch adjustment 2. Control cable adjustment 3. Shift solenoid valve A ON vehicle Failure to change gear from D1 to D2. 4. Control valve assembly 5. Vehicle speed sensorA/T (Revolution sensor) and vehicle speed sensorMTR OFF vehicle 6. Brake band 1. PNP switch adjustment 2. Control cable adjustment 3. Shift solenoid valve B ON vehicle No Up Shift Failure to change gear from D2 to D3. 4. Control valve assembly 5. Vehicle speed sensorA/T (Revolution sensor) and vehicle speed sensorMTR 6. High clutch OFF vehicle 7. Brake band 1. PNP switch adjustment 2. Control cable adjustment 3. Shift solenoid valve A ON vehicle Failure to change gear from D3 to D4. 4. Vehicle speed sensorA/T (Revolution sensor) and vehicle speed sensorMTR 5. A/T fluid temperature sensor OFF vehicle 6. Brake band AT-286 AT-281 AT-281 AT-181 AT-119, AT-215 AT-113 AT-286 EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-119, AT-215 AT-181 AT-187 AT-62 AT-280 AT-286 Reference Page AT-281 AT-281 AT-181 AT-280
GI MA EM
AT-119, AT-215 AT-286 AT-281 AT-281 AT-187 AT-280 AT-119, AT-215 AT-331
LC EC FE CL MT
1. Throttle position sensor (Adjustment) Too high a gear change point from D1 to D2, from D2 to D3, from D3 to D4. AT-243, 246, 249 Improper Shift Timing
ON vehicle
2. Vehicle speed sensorA/T (Revolution sensor) and vehicle speed sensorMTR 3. Shift solenoid valve A 4. Shift solenoid valve B 1. Fluid level
Gear change directly from D1 to D3 occurs.
ON vehicle 2. Accumulator servo release OFF vehicle 3. Brake band
AT-89

Item Symptom Condition Diagnostic Item Reference Page EC-53, Idle Speed/Ignition Timing/Idle Mixture Ratio Adjustment AT-291 AT-280 AT-291 EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-66 AT-280 AT-280 AT-113 AT-286 EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-66 AT-280 AT-331 AT-286 EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-66 AT-280 AT-286 AT-336
1. Engine idling rpm Engine stops when shifting lever into R, D, 2 and 1. ON vehicle 2. Torque converter clutch solenoid valve 3. Control valve assembly OFF vehicle 4. Torque converter
NOT USED
Too sharp a shock in change from D1 to D2.
ON vehicle
2. Line pressure test 3. Accumulator servo release 4. Control valve assembly 5. A/T fluid temperature sensor
OFF vehicle
6. Brake band
1. Throttle position sensor (Adjustment) ON vehicle Shift Shock Too sharp a shock in change from D2 to D3. 2. Line pressure test 3. Control valve assembly 4. High clutch OFF vehicle 5. Brake band
1. Throttle position sensor (Adjustment) ON vehicle Too sharp a shock in change from D3 to D4. 2. Line pressure test 3. Control valve assembly 4. Brake band OFF vehicle 5. Overrun clutch
AT-90

Item Symptom Condition Diagnostic Item 1. Fluid level Reference Page AT-62 EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-66 AT-280 AT-280 AT-286 AT-62 EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-66 AT-280 AT-331 AT-286 AT-62 EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-66 AT-280 AT-331 AT-286 AT-62 AT-327 AT-343 AT-331 AT-286 AT-62 AT-286
2. Throttle position sensor (Adjustment) Almost no shock or clutches slipping in change from D1 to D2. ON vehicle 3. Line pressure test 4. Accumulator servo release 5. Control valve assembly OFF vehicle 6. Brake band 1. Fluid level
ON vehicle Slips/Will Not Engage Almost no shock or slipping in change from D2 to D3.
3. Line pressure test 4. Control valve assembly 5. High clutch OFF vehicle 6. Brake band 1. Fluid level
ON vehicle Almost no shock or slipping in change from D3 to D4.
3. Line pressure test 4. Control valve assembly 5. High clutch OFF vehicle 6. Brake band ON vehicle 1. Fluid level 2. Reverse clutch
Vehicle braked by gear change from D1 to D2. NOT USED
3. Low & reverse brake OFF vehicle 4. High clutch 5. Low one-way clutch
Vehicle braked by gear change from D2 to D3.
ON vehicle OFF vehicle
1. Fluid level 2. Brake band
AT-91

Item Symptom Condition ON vehicle Vehicle braked by gear change from D3 to D4. Diagnostic Item 1. Fluid level 2. Overrun clutch OFF vehicle 3. Forward one-way clutch 4. Reverse clutch 1. Fluid level 2. PNP switch adjustment ON vehicle NOT USED 3. Shift solenoid valve A 4. Shift solenoid valve B 5. Control valve assembly Maximum speed not attained. Acceleration poor. 6. Reverse clutch 7. High clutch 8. Brake band OFF vehicle 9. Low & reverse brake 10. Oil pump 11. Torque converter 1. Fluid level AT-343 AT-308 AT-291 AT-62 EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-202 AT-181 AT-174 AT-280 AT-343 AT-336 AT-62 EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-181 AT-187 AT-280 AT-331 AT-286 Reference Page AT-62 AT-336 AT-347 AT-327 AT-62 AT-281 AT-181 AT-187 AT-280 AT-327 AT-331 AT-286
2. Throttle position sensor (Adjustment) ON vehicle Failure to change gear from D4 to D3. 3. Overrun clutch solenoid valve 4. Shift solenoid valve A 5. Line pressure solenoid valve 6. Control valve assembly 7. Low & reverse brake No Down Shift OFF vehicle 8. Overrun clutch 1. Fluid level
2. Throttle position sensor (Adjustment) ON vehicle Failure to change gear from D3 to D2 or from D4 to D2. 3. Shift solenoid valve A 4. Shift solenoid valve B 5. Control valve assembly 6. High clutch OFF vehicle 7. Brake band
AT-92

Item Symptom Condition Diagnostic Item 1. Fluid level Reference Page AT-62 EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-181 AT-187 AT-280 AT-374 AT-331 AT-286 EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-66 AT-202 AT-280 EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-119, AT-215 EC-177, DTC P0120 THROTTLE POSITION SENSOR
2. Throttle position sensor (Adjustment) ON vehicle No Down Shift Failure to change gear from D2 to D1 or from D3 to D1. 3. Shift solenoid valve A 4. Shift solenoid valve B 5. Control valve assembly 6. Low one-way clutch OFF vehicle 7. High clutch 8. Brake band
1. Throttle position sensor (Adjustment) Shift Shock Gear change shock felt during deceleration by releasing accelerator pedal. ON vehicle 2. Line pressure test 3. Overrun clutch solenoid valve 4. Control valve assembly
1. Throttle position sensor (Adjustment) Too high a change point from D4 to D3, from D3 to D2 , from D2 to D1. ON vehicle 2. Vehicle speed sensorA/T (Revolution sensor) and vehicle speed sensorMTR
AX SU BR ST RS BT HA SC
1. Throttle position sensor (Adjustment) Kickdown does not operate when depressing pedal in D4 within kickdown vehicle speed. ON vehicle
Improper Shift Timing
2. Revolution sensor and vehicle AT-119, AT-215 speed sensor 3. Shift solenoid valve A 4. Shift solenoid valve B 1. Vehicle speed sensorA/T (Revolution sensor) and vehicle speed sensorMTR AT-181 AT-187 AT-119, AT-215 EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-181 AT-187
Kickdown operates or engine overruns when depressing pedal in D4 beyond kickdown ON vehicle vehicle speed limit.
EL IDX
3. Shift solenoid valve A 4. Shift solenoid valve B
AT-93

Item Symptom Condition Diagnostic Item 1. Fluid level Reference Page AT-62 EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-66 AT-174 AT-280 AT-331 AT-336 AT-62 EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-66 AT-174 AT-181 AT-280 AT-286 AT-336 AT-62 EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-66 AT-174 AT-280 AT-113 AT-286 AT-336 AT-331
2. Throttle position sensor (Adjustment) ON vehicle Races extremely fast or slips in changing from D4 to D3 when depressing pedal. 3. Line pressure test 4. Line pressure solenoid valve 5. Control valve assembly 6. High clutch OFF vehicle 7. Forward clutch 1. Fluid level
2. Throttle position sensor (Adjustment) ON vehicle Races extremely fast or slips in changing from D4 to D2 when depressing pedal. 3. Line pressure test 4. Line pressure solenoid valve 5. Shift solenoid valve A 6. Control valve assembly 7. Brake band OFF vehicle 8. Forward clutch 1. Fluid level
Slips/Will Not Engage
2. Throttle position sensor (Adjustment) ON vehicle 3. Line pressure test Races extremely fast or slips in changing from D3 to D2 when depressing pedal. 4. Line pressure solenoid valve 5. Control valve assembly 6. A/T fluid temperature sensor 7. Brake band OFF vehicle 8. Forward clutch 9. High clutch
AT-94

Item Symptom Condition Diagnostic Item 1. Fluid level Reference Page AT-62 EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-66 AT-174 AT-280 AT-336 AT-347 AT-286 AT-62 AT-281 AT-66 AT-174 AT-308 AT-331 AT-286 AT-343 AT-291 AT-368 AT-62 AT-291 AT-281 EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-202 AT-187 AT-181 AT-280 AT-281 AT-286 AT-336 AT-281
2. Throttle position sensor (Adjustment) ON vehicle Races extremely fast or slips in changing from D4 or D3 to D1 when depressing pedal. 3. Line pressure test 4. Line pressure solenoid valve 5. Control valve assembly 6. Forward clutch OFF vehicle Slips/Will Not Engage 7. Forward one-way clutch 8. Low one-way clutch 1. Fluid level 2. Control cable adjustment ON vehicle 3. Line pressure test 4. Line pressure solenoid valve 5. Oil pump Vehicle will not run in any position. 6. High clutch 7. Brake band OFF vehicle 8. Low & reverse brake 9. Torque converter 10. Parking components NOT USED Transmission noise in D, 2, 1 and R positions. ON vehicle OFF vehicle 1. Fluid level 2. Torque converter 1. PNP switch adjustment
No Down Shift
Failure to change from D3 to 22 when changing lever into 2 position. AT-237
ON vehicle
3. Overrun clutch solenoid valve 4. Shift solenoid valve B 5. Shift solenoid valve A 6. Control valve assembly 7. Control cable adjustment 8. Brake band
OFF vehicle 9. Overrun clutch Improper Shift Timing Gear change from 22 to 23 in 2 position. ON vehicle 1. PNP switch adjustment
AT-95

Item Symptom Condition Diagnostic Item 1. PNP switch adjustment 2. Control cable adjustment Reference Page AT-281 AT-281 EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-119, AT-215 AT-181 AT-280 AT-202 AT-336 AT-343 AT-281 AT-281 AT-281 AT-119, AT-215 AT-181 AT-280 AT-202 AT-336 AT-343 AT-280 AT-343
3. Throttle position sensor (Adjustment) ON vehicle 4. Vehicle speed sensorA/T (Revolution sensor) and vehicle speed sensorMTR 5. Shift solenoid valve A 6. Control valve assembly 7. Overrun clutch solenoid valve 8. Overrun clutch OFF vehicle 9. Low & reverse brake Improper Shift Timing 1. PNP switch adjustment Gear change from 11 to 12 in 1 position. ON vehicle 2. Control cable adjustment 1. PNP switch adjustment 2. Vehicle speed sensorA/T (Revolution sensor) and vehicle speed sensorMTR 3. Shift solenoid valve A 4. Control valve assembly 5. Overrun clutch solenoid valve 6. Overrun clutch OFF vehicle 7. Low & reverse brake Shift Shock Large shock changing from 12 to 11 in 1 ON vehicle position. OFF vehicle 1. Control valve assembly 2. Low & reverse brake
NOT USED
Engine brake does not operate in 1 position. AT-259
ON vehicle No Down Shift Does not change from 12 to 11 in 1 position.
AT-96

Item Symptom Condition Diagnostic Item 1. Fluid level Reference Page AT-62 EC-53, Idle speed/ignition timing/idle mixture ratio adjustment EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-66 AT-174 AT-280 AT-308 AT-327 AT-331 AT-286 AT-336 AT-336 AT-343 AT-291 AT-62 AT-327 AT-331 AT-286 AT-336 AT-336 AT-343 AT-62 AT-291 AT-308 AT-327 AT-331 AT-286 AT-336 AT-336 AT-343
2. Engine idling rpm
ON vehicle
4. Line pressure test Transmission overheats. 5. Line pressure solenoid valve 6. Control valve assembly 7. Oil pump 8. Reverse clutch NOT USED OFF vehicle 11. Forward clutch 12. Overrun clutch 13. Low & reverse brake 14. Torque converter ON vehicle 1. Fluid level 2. Reverse clutch ATF shoots out during operation. White smoke emitted from exhaust pipe during operation. 3. High clutch 4. Brake band OFF vehicle 5. Forward clutch 6. Overrun clutch 7. Low & reverse brake ON vehicle 1. Fluid level 2. Torque converter 3. Oil pump 4. Reverse clutch NOT USED Offensive smell at fluid charging pipe. OFF vehicle 6. Brake band 7. Forward clutch 8. Overrun clutch 9. Low & reverse brake 5. High clutch 9. High clutch 10. Brake band
AT-97

Item Symptom Condition Diagnostic Item Reference Page EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-119, AT-215 AT-281 AT-124 AT-113 AT-66 AT-157 AT-280 AT-291 AT-62 EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-66 AT-157 AT-174 AT-280 AT-291 EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-119, AT-215
2. Vehicle speed sensorA/T (Revolution sensor) and vehicle speed sensorMTR ON vehicle Torque converter is not locked up. 4. Engine speed signal 5. A/T fluid temperature sensor 6. Line pressure test 7. Torque converter clutch solenoid valve 8. Control valve assembly OFF vehicle 9. Torque converter 1. Fluid level No Lock-up Engagement/ TCC Inoperative ON vehicle Torque converter clutch piston slip. 3. PNP switch adjustment
3. Line pressure test 4. Torque converter clutch solenoid valve 5. Line pressure solenoid valve 6. Control valve assembly
OFF vehicle
7. Torque converter
Lock-up point is extremely high or low. AT-252
ON vehicle
2. Vehicle speed sensorA/T (Revolution sensor) and vehicle speed sensorMTR 3. Torque converter clutch solenoid valve 4. Control valve assembly
AT-157 AT-280
AT-98

Item Symptom Condition Diagnostic Item Reference Page EC-177, DTC P0120 THROTTLE POSITION SENSOR AT-281 AT-119, AT-215
GI MA EM LC
2. PNP switch adjustment 3. Vehicle speed sensorA/T (Revolution sensor) and vehicle speed sensorMTR 4. Shift solenoid valve A 5. Overrun clutch solenoid valve 6. Control valve assembly 7. A/T fluid temperature sensor 8. Line pressure test 9. Brake band OFF vehicle 10. Overrun clutch 1. Fluid level 2. Torque converter clutch solenoid valve ON vehicle 3. Shift solenoid valve B 4. Shift solenoid valve A 5. Control valve assembly
ON vehicle No Up Shift A/T does not shift to D4 when driving with overdrive control switch ON.
AT-181 AT-202 AT-280 AT-113 AT-66 AT-286 AT-336 AT-62 AT-157 AT-187 AT-181 AT-280
EC FE CL MT
NOT USED
Engine is stopped at R, D, 2 and 1 positions.
AX SU BR
TCM Terminals and Reference Value

PREPARATION
ST RS BT HA
Measure voltage between each terminal and terminal 25 or 48 by following TCM INSPECTION TABLE.
SAT216J
SC EL IDX
AT-99

TCM Terminals and Reference Value (Contd)
TCM HARNESS CONNECTOR TERMINAL LAYOUTNCAT0030S02
SAT403J
TCM INSPECTION TABLE

(Data are reference values.)
Terminal No. Wire color Item Condition When releasing accelerator pedal after warming up engine. When depressing accelerator pedal fully after warming up engine. When releasing accelerator pedal after warming up engine. When depressing accelerator pedal fully after warming up engine. When A/T performs lock-up.
NCAT0030S03
Judgement standard (Approx.) 1.5 - 2.5V 0V 5 - 14V 0V 8 - 15V
R/W
Line pressure solenoid valve
P/B
Line pressure solenoid valve (with dropping resistor)
GY/R
Torque converter clutch solenoid valve
When A/T does not perform lock-up. 0V When turning ignition switch to ON. Battery voltage 0V
5 *2 6 *2 7 *2 8*2 9*2
Y/R Y/G Y/B BR/W G/Y
10
Power source When turning ignition switch to OFF. When shift solenoid valve A operates. (When driving in D1 or D4.) When shift solenoid valve A does not operate. (When driving in D2 or D3.) When shift solenoid valve B operates. (When driving in D1 or D2.) When shift solenoid valve B does not operate. (When driving in D3 or D4.)
Battery voltage
11
L/W
0V
Battery voltage
12
L/Y
0V
AT-100

Terminal No. Judgement standard (Approx.) 0V Battery voltage
Wire color
Item
Condition When setting overdrive control switch in OFF position. When setting overdrive control switch in ON position. When releasing accelerator pedal after warming up engine. Refer to TCM SELF-DIAGNOSTIC PROCEDURE (No tools), AT-49. When depressing accelerator pedal after warming up engine. Refer to TCM SELF-DIAGNOSTIC PROCEDURE (No tools), AT-49. When depressing accelerator pedal more than half-way after warming up engine. When releasing accelerator pedal after warming up engine. When ASCD cruise is being performed. (CRUISE light comes on.)
GI MA EM
13
G/W
O/D OFF indicator lamp
15 *2
PU
LC
Battery voltage
16
Closed throttle position switch (in throttle position switch)
EC
0V
FE CL MT
17
LG
Wide open throttle position switch (in throttle position switch)
Battery voltage
0V Battery voltage
18
OR
ASCD cruise switch
When ASCD cruise is not being performed. (CRUISE light does not 0V comes on.)
AX SU
19
Power source
Same as No. 10
BR
20 L/B Overrun clutch solenoid valve When overrun clutch solenoid valve operates. When overrun clutch solenoid valve does not operate. When setting overdrive control switch in ON position When setting overdrive control switch in OFF position Battery voltage
ST RS
0V
Battery voltage
22
OR/B
Overdrive control switch
BT
0V When ACCEL set switch on ASCD 5 - 8V cruise is in D4 position. When ACCEL set switch on ASCD 0V cruise is in D3 position.
HA SC EL IDX
24
W/B
ASCD OD cut signal
AT-101

Terminal No. 25 Judgement standard (Approx.) When setting selector lever to 1 position. When setting selector lever to other positions. When setting selector lever to 2 position. When setting selector lever to other positions. When turning ignition switch to OFF. 28 P Power source (Memory back-up) or When turning ignition switch to ON. Battery voltage Battery voltage 0V Battery voltage 0V
Wire color B
Item Ground
Condition
26
SB
PNP switch 1 position
27
L/OR
Battery voltage
29
Revolution sensor
When moving at 20 km/h (12 MPH), use the CONSULT-II pulse frequency measuring function.*1 CAUTION: Connect the diagnosis data link 150Hz cable to the vehicle diagnosis connector. *1: A circuit tester cannot be used to test this item. When vehicle parks. Under 1.3V or over 4.5V 4.5 - 5.5V 0V Battery voltage 0V Battery voltage 0V
30 *3 31 *3 32
G/B GY/L P/L
Throttle position sensor (Power source)
Ignition switch ON Ignition switch OFF. When setting selector lever to D position. When setting selector lever to other positions. When setting selector lever to R position. When setting selector lever to other positions.
34
LG
PNP switch D position
35
PNP switch R position
36
GY/R
PNP switch N or P position
When setting selector lever to N or Battery voltage P position. When setting selector lever to other positions. 0V
39
Engine speed signal
Refer to EC-134, ECM Inspection Table.
AT-102

Terminal No. Judgement standard (Approx.)
Wire color
Item
Condition
40
Y/G
Vehicle speed sensor
Voltage varies When moving vehicle at 2 to 3 km/h between less (1 to 2 MPH) for 1 m (3 ft) or more. than 1V and more than 4.5V Fully-closed When depressing accelerator pedal throttle: slowly after warming up engine. 0.5V (Voltage rises gradually in response Fully-open to throttle position.) throttle: 4V When depressing brake pedal. Battery voltage 0V 1.5V 0.5V
41
GY
42
Throttle position sensor (Ground) Stop lamp switch
45
R/G
When releasing brake pedal. When ATF temperature is 20C (68F). When ATF temperature is 80C (176F).
47
BR
48
Ground
*2: This terminal is connected to the ECM. *3: These terminals are connected to the Data link connector.
AT-103
TROUBLE DIAGNOSIS FOR POWER SUPPLY

Wiring Diagram AT MAIN
Wiring Diagram AT MAIN
NCAT0031
TAT222
AT-104

Wiring Diagram AT MAIN (Contd)
TCM TERMINALS AND REFERENCE VALUE

Remarks: Specification data are reference values. Terminal No. Wire color Item Condition When turning ignition switch to ON. 10 R Power source When turning ignition switch to OFF. 19 25 R B Power source Ground When turning ignition switch to OFF. 28 P Power source (Memory back-up) or When turning ignition switch to ON. Same as No. 10 0V
NCAT0031S01
Judgement standard (Approx.) Battery voltage
GI MA EM LC EC
Battery voltage
FE
Battery voltage
CL
48 B Ground
MT
AX SU BR
Diagnostic Procedure
1 CHECK TCM POWER SOURCE STEP 1
1. Turn ignition switch to ON position. (Do not start engine.) 2. Check voltage between TCM terminals 10, 19, 28 and ground.
NCAT0228
ST RS BT HA SC EL
SAT611J
OK or NG OK NG GO TO 2. GO TO 3.
IDX
AT-105

Diagnostic Procedure (Contd)
CHECK TCM POWER SOURCE STEP 2
1. Turn ignition switch to OFF position. 2. Check voltage between TCM terminal 28 and ground.
SAT612JD
DETECT MALFUNCTIONING ITEM
Check the following items: Harness for short or open between ignition switch and TCM terminals 10, 19 and 28 (Main harness) Fuse Ignition switch Refer to EL-9, POWER SUPPLY ROUTING. OK or NG OK NG GO TO 4. Repair or replace damaged parts.
CHECK TCM GROUND CIRCUIT
1. Turn ignition switch to OFF position. 2. Disconnect TCM harness connector. 3. Check continuity between TCM terminals 25, 48 and ground. Refer to wiring diagram AT MAIN. Continuity should exist. If OK, check harness for short to ground and short to power. OK or NG OK NG INSPECTION END Repair open circuit or short to ground or short to power in harness or connectors.
AT-106
DTC P0705 PARK/NEUTRAL POSITION (PNP) SWITCH

Description
Description

NCAT0032
The PNP switch assembly includes a transmission range switch. The transmission range switch detects the selector lever position and sends a signal to the TCM.
GI MA EM
SAT088JA
LC
NCAT0032S01
Remarks: Specification data are reference values. Terminal No. Wire color Item Condition When setting selector lever to 1 position. When setting selector lever to other positions. When setting selector lever to 2 position. When setting selector lever to other positions. When setting selector lever to D position. When setting selector lever to other positions. When setting selector lever to R position. When setting selector lever to other positions. Judgement standard (Approx.) Battery voltage
EC FE CL
0V
26
SB
MT
Battery voltage 0V Battery voltage 0V Battery voltage
27
L/OR
AX SU BR
34
LG
PNP switch D position
35
PNP switch R position
0V
36
GY/R
PNP switch N or P position
When setting selector lever to N or Battery voltage P position. When setting selector lever to other positions. 0V
ON BOARD DIAGNOSIS LOGIC

Diagnostic trouble code : PNP SW/CIRC : P0705 Malfunction is detected when ... TCM does not receive the correct voltage signal from the switch based on the gear position. Check items (Possible cause) Harness or connectors (The PNP switch circuit is open or shorted.) PNP switch
NCAT0032S02
AT-107

Description (Contd)
DIAGNOSTIC TROUBLE CODE (DTC) CONFIRMATION PROCEDURE NCAT0032S03

CAUTION: Always drive vehicle at a safe speed. NOTE: If DIAGNOSTIC TROUBLE CODE CONFIRMATION PROCEDURE has been previously conducted, always turn ignition switch OFF and wait at least 5 seconds before conducting the next test. After the repair, perform the following procedure to confirm the malfunction is eliminated. With CONSULT-II 1) Turn ignition switch ON. 2) Select DATA MONITOR mode for ENGINE with CONSULTII. 3) Start engine and maintain the following conditions for at least 5 consecutive seconds. VHCL SPEED SE: 10 km/h (6 MPH) or more THRTL POS SEN: More than 1.3V Selector lever: D position (OD ON or OFF) With GST Follow the procedure With CONSULT-II.
SAT014K
SEF949Y
AT-108

Wiring Diagram AT PNP/SW
Wiring Diagram AT PNP/SW
NCAT0199
TAT270
AT-109

1 CHECK PNP SWITCH CIRCUIT (With CONSULT-II)
With CONSULT-II 1. Turn ignition switch to ON position. (Do not start engine.) 2. Select TCM INPUT SIGNALS in DATA MONITOR mode for A/T with CONSULT-II.
NCAT0033
SAT014K
3. Read out P/N, R, D, 2 and 1 position switches moving selector lever to each position. Check the signal of the selector lever position is indicated properly.
SAT701J
OK or NG OK NG GO TO 3. Check the following items: PNP switch Refer to Component Inspection, AT-112. Harness for short or open between ignition switch and PNP switch (Main harness) Harness for short or open between PNP switch and TCM (Main harness) Ignition switch and fuse Refer to EL-9, POWER SUPPLY ROUTING. Diode (P, N positions)
AT-110

CHECK PNP SWITCH CIRCUIT (Without CONSULT-II)
Without CONSULT-II 1. Turn ignition switch to ON position. (Do not start engine.) 2. Check voltage between TCM terminals 26, 27, 34, 35, 36 and ground while moving selector lever through each position. Voltage: B: Battery voltage 0: 0V
GI MA EM LC EC
MTBL0136
FE CL MT
SAT425J
OK or NG OK NG GO TO 3. Check the following items: PNP switch Refer to Component Inspection, AT-112. Harness for short or open between ignition switch and PNP switch (Main harness) Harness for short or open between PNP switch and TCM (Main harness) Ignition switch and fuse Refer to EL-9, POWER SUPPLY ROUTING. Diode (P, N positions)
AT-111

CHECK DTC
Perform Diagnostic Trouble Code (DTC) confirmation procedure, AT-108. OK or NG OK NG INSPECTION END 1. Perform TCM input/output signal inspection. 2. If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
Component Inspection
PARK/NEUTRAL POSITION SWITCH
1.
Check continuity between terminals 1 and 3 and between terminals 2 and 4, 5, 6, 7, 8, 9 while moving manual shaft through each position.
Lever position P R N D 2 1 37 38 39 36 35 34 12 Terminal No. 12
SAT402J
2. 3. 4. 5. 6.
If NG, check again with control cable disconnected from manual shaft of A/T assembly. Refer to step 1. If OK on step 2, adjust control cable. Refer to AT-281. If NG on step 2, remove PNP switch from A/T and check continuity of PNP switch terminals. Refer to step 1. If OK on step 4, adjust PNP switch. Refer to AT-281. If NG on step 4, replace PNP switch.
SAT089JA
AT-112
DTC P0710 A/T FLUID TEMPERATURE SENSOR CIRCUIT

Description
Description
NCAT0035
The A/T fluid temperature sensor detects the A/T fluid temperature and sends a signal to the TCM.
GI MA EM
SAT283HB
LC EC FE CL
SAT021J
MT
CONSULT-II REFERENCE VALUE IN DATA MONITOR MODE NCAT0035S01
Remarks: Specification data are reference values. Monitor item A/T fluid temperature sensor Condition Cold [20C (68F)] " Hot [80C (176F)] Specification (Approximately) 1.5V " 0.5V 2.5 k " 0.3 k
AX SU BR

Remarks: Specification data are reference values. Terminal No. Wire color Item Throttle position sensor (Ground) Condition
NCAT0035S02
ST RS BT HA SC
Judgement standard (Approx.)
42
47
BR
When ATF temperature is 20C (68F). When ATF temperature is 80C (176F).
1.5V 0.5V

Diagnostic trouble code : ATF TEMP SEN/CIRC : P0710 Malfunction is detected when ... TCM receives an excessively low or high voltage from the sensor. Check items (Possible cause)
NCAT0035S03
EL IDX
Harness or connectors (The sensor circuit is open or shorted.) A/T fluid temperature sensor
AT-113

Description (Contd)

CAUTION: Always drive vehicle at a safe speed. NOTE: If DIAGNOSTIC TROUBLE CODE CONFIRMATION PROCEDURE has been previously conducted, always turn ignition switch OFF and wait at least 5 seconds before conducting the next test. After the repair, perform the following procedure to confirm the malfunction is eliminated. With CONSULT-II 1) Turn ignition switch ON and select DATA MONITOR mode for ENGINE with CONSULT-II. 2) Start engine and maintain the following conditions for at least 10 minutes (Total). (It is not necessary to maintain continuously.) CMPSRPM (REF): 450 rpm or more VHCL SPEED SE: 10 km/h (6 MPH) or more THRTL POS SEN: More than 1.2V Selector lever: D position (OD ON) With GST Follow the procedure With CONSULT-II.
SAT014K
SEF949Y
AT-114

Wiring Diagram AT FTS
Wiring Diagram AT FTS
NCAT0200
TAT224
AT-115

1 INSPECTION START
Do you have CONSULT-II? Yes or No Yes No GO TO 2. GO TO 3.
NCAT0036
CHECK INPUT SIGNAL OF A/T FLUID TEMPERATURE SENSOR (With CONSULT-II)
With CONSULT-II 1. Start engine. 2. Select TCM INPUT SIGNALS in DATA MONITOR mode for A/T with CONSULT-II.
SAT014K
3. Read out the value of FLUID TEMP SE. Voltage: Cold [20C (68F)] Hot [80C (176F)]: Approximately 1.5V 0.5V
SAT614J
AT-116

CHECK INPUT SIGNAL OF A/T FLUID TEMPERATURE SENSOR (Without CONSULT-II)
Without CONSULT-II 1. Start engine. 2. Check voltage between TCM terminal 47 and ground while warming up A/T. Voltage: Cold [20C (68F)] Hot [80C (176F)]: Approximately 1.5V 0.5V
GI MA EM LC EC FE
SAT937J
3. Turn ignition switch to OFF position. 4. Disconnect TCM harness connector. 5. Check continuity between terminal 42 and ground. Continuity should exist.
CL MT
AX SU
SAT421J
If OK, check harness for short to ground and short to power. OK or NG OK NG GO TO 4. GO TO 5.
BR ST RS
CHECK DTC
BT HA SC EL IDX
AT-117

CHECK A/T FLUID TEMPERATURE SENSOR WITH TERMINAL CORD ASSEMBLY
1. Turn ignition switch to OFF position. 2. Disconnect terminal cord assembly connector in engine compartment. 3. Check resistance between terminals 6 and 7 when A/T is cold. Resistance: Cold [20C (68F)] Approximately 2.5 k
SAT880J
4. Reinstall any part removed. OK or NG OK (With CONSULT-II) OK (Without CONSULTII) NG GO TO 2. GO TO 3. 1. Remove oil pan. 2. Check the following items: A/T fluid temperature sensor Refer to Component Inspection, AT-118. Harness of terminal cord assembly for short or open
A/T FLUID TEMPERATURE SENSOR

For removal, refer to AT-280. Check resistance between two terminals while changing temperature as shown at left.
Temperature C (F) 20 (68) 80 (176) Resistance Approximately 2.5 k Approximately 0.3 k
SAT298F
AT-118
DTC P0720 VEHICLE SPEED SENSORA/T (REVOLUTION SENSOR)

Description
Description
NCAT0038
The revolution sensor detects the revolution of the idler gear parking pawl lock gear and emits a pulse signal. The pulse signal is sent to the TCM which converts it into vehicle speed.
GI MA EM
SAT357H
LC
NCAT0038S01
Remarks: Specification data are reference values. Terminal No. Wire color Item Condition Judgement standard (Approx.)
EC FE CL MT
29
Revolution sensor
When moving at 20 km/h (12 MPH), use the CONSULT-II pulse frequency measuring function.*1 CAUTION: Connect the diagnosis data link 150 Hz cable to the vehicle diagnosis connector. *1: A circuit tester cannot be used to test this item. When vehicle parks. Under 1.3V or over 4.5V
AX SU BR
42
Throttle position sensor (Ground)

Diagnostic trouble code : VEH SPD SEN/CIR AT : P0720 Malfunction is detected when ... TCM does not receive the proper voltage signal from the sensor. Check items (Possible cause)
NCAT0038S02
Harness or connectors (The sensor circuit is open or shorted.) Revolution sensor
AT-119

Description (Contd)

CAUTION: Always drive vehicle at a safe speed. Be careful not to rev engine into the red zone on the tachometer. NOTE: If DIAGNOSTIC TROUBLE CODE CONFIRMATION PROCEDURE has been previously conducted, always turn ignition switch OFF and wait at least 5 seconds before conducting the next test. After the repair, perform the following procedure to confirm the malfunction is eliminated. With CONSULT-II 1) Turn ignition switch ON and select DATA MONITOR mode for A/T with CONSULT-II. 2) Drive vehicle and check for an increase of VHCL/S SEMTR value. If the check result is NG, go to DIAGNOSTIC PROCEDURE, AT-218. If the check result is OK, go to following step. 3) Select DATA MONITOR mode for ENGINE with CONSULTII. 4) Start engine and maintain the following conditions for at least 5 consecutive seconds. VHCL SPEED SE: 30 km/h (19 MPH) or more THRTL POS SEN: More than 1.2V Selector lever: D position (OD ON) Driving location: Driving the vehicle uphill (increased engine load) will help maintain the driving conditions required for this test. If the check result is NG, go to DIAGNOSTIC PROCEDURE, AT-122. If the check result is OK, go to following step. 5) Maintain the following conditions for at least 5 consecutive seconds. CMPSRPM (REF): 3,500 rpm or more THRTL POS SEN: More than 1.2V Selector lever: D position (OD ON) Driving location: Driving the vehicle uphill (increased engine load) will help maintain the driving conditions required for this test. With GST Follow the procedure With CONSULT-II.
SAT014K
SAT971J
SAT014K
SEF949Y
AT-120

Wiring Diagram AT VSSA/T
Wiring Diagram AT VSSA/T
NCAT0201
TAT225
AT-121

1 CHECK INPUT SIGNAL (With CONSULT-II)
NCAT0039
SAT014K
3. Read out the value of VHCL/S SEA/T while driving. Check the value changes according to driving speed.
SAT614J
CHECK REVOLUTION SENSOR (With CONSULT-II)
With CONSULT-II Start engine.
MTBL0578
Harness for short open between TCM, ECM and revolution sensor (Main harness) OK or NG OK NG GO TO 3. Repair or replace damaged parts.
AT-122

CHECK DTC
Perform Diagnostic Trouble Code (DTC) confirmation procedure, AT-120. OK or NG OK NG INSPECTION END GO TO 4.
CHECK TCM INSPECTION
1. Perform TCM input/output signal inspection. 2. If NG, recheck TCM pin terminals for damage or loose connection with harness connector. OK or NG OK NG INSPECTION END Repair or replace damaged parts.
AT-123
DTC P0725 ENGINE SPEED SIGNAL

Description
Description
The engine speed signal is sent from the ECM to the TCM.
NCAT0041

Remarks: Specification data are reference values. Terminal No. Wire color Item Condition
NCAT0041S01
39
Engine speed signal
Refer to EC-134, ECM INSPECTION TABLE.

Diagnostic trouble code : ENGINE SPEED SIG : P0725 Malfunction is detected when ... Check item (Possible cause)
NCAT0041S02
TCM does not receive the proper voltage Harness or connectors signal from ECM. (The sensor circuit is open or shorted.)

CAUTION: Always drive vehicle at a safe speed. NOTE: If DIAGNOSTIC TROUBLE CODE CONFIRMATION PROCEDURE has been previously conducted, always turn ignition switch OFF and wait at least 5 seconds before conducting the next test. After the repair, perform the following procedure to confirm the malfunction is eliminated. With CONSULT-II 1) Turn ignition switch ON and select DATA MONITOR mode for ENGINE with CONSULT-II. 2) Start engine and maintain the following conditions for at least 10 consecutive seconds. VHCL SPEED SE: 10 km/h (6 MPH) or more THRTL POS SEN: More than 1.2V Selector lever: D position (OD ON) With GST Follow the procedure With CONSULT-II.
SAT014K
SEF949Y
AT-124

Wiring Diagram AT ENGSS
Wiring Diagram AT ENGSS
NCAT0202
TAT226
AT-125

1 CHECK DTC WITH ECM
Perform diagnostic test mode II (self- diagnostic results) for engine control. Check ignition signal circuit condition. OK or NG OK (With CONSULT-II) OK (Without CONSULTII) NG GO TO 2. GO TO 3.
NCAT0042
Check ignition signal circuit for engine control. Refer to EC-590, DTC P1320 IGNITION SIGNAL.
CHECK INPUT SIGNAL (With CONSULT-II)
SAT014K
3. Read out the value of ENGINE SPEED. Check engine speed changes according to throttle position.
SAT645J
OK or NG OK NG GO TO 4. Check the following items: Harness for short or open between TCM and ECM Resistor and ignition coil Refer to EC-590, DTC P1320 IGNITION SIGNAL.
AT-126

CHECK INPUT SIGNAL (Without CONSULT-II)
Without CONSULT-II 1. Start engine. 2. Check voltage between TCM terminal 39 and ground. Voltage (Idle speed): Refer to EC-632, Idle Speed and Ignition Timing.
GI MA EM LC EC FE
SAT424J
OK or NG OK NG GO TO 4. Check the following items: Harness for short or open between TCM and ECM Resistor and ignition coil Refer to EC-590, DTC P1320 IGNITION SIGNAL.
CL MT
CHECK DTC
AT-127
DTC P0731 A/T 1ST GEAR FUNCTION

Description
Description

NCAT0043
This is an OBD-II self-diagnostic item and not available in TCM self-diagnosis. This malfunction will not be detected while the O/D OFF indicator lamp is indicating another self-diagnosis malfunction. This malfunction is detected when the A/T does not shift into first gear position as instructed by the TCM. This is not caused by electrical malfunction (circuits open or shorted) but by mechanical malfunction such as control valve sticking, improper solenoid valve operation, etc.
2 OFF (Open) ON (Closed) 3 OFF (Open) OFF (Open) 4 ON (Closed) OFF (Open)
Gear position Shift solenoid valve A Shift solenoid valve B
1 ON (Closed) ON (Closed)

Remarks: Specification data are reference values. Terminal No. Wire color Item Condition When shift solenoid valve A operates. (When driving in D1 or D4.) When shift solenoid valve A does not operate. (When driving in D2 or D3.) When shift solenoid valve B operates. (When driving in D1 or D2.) When shift solenoid valve B does not operate. (When driving in D3 or D4.)
NCAT0043S01
11
L/W
0V
Battery voltage
12
L/Y
0V
ON BOARD DIAGNOSTIC LOGIC
NCAT0043S02
This diagnosis monitors actual gear position by checking the torque converter slip ratio calculated by TCM as follows: Torque converter slip ratio = A x C/B A: Output shaft revolution signal from revolution sensor B: Engine speed signal from ECM C: Gear ratio determined as gear position which TCM supposes If the actual gear position is higher than the position (1st) supposed by TCM, the slip ratio will be more than normal. In case the ratio exceeds the specified value, TCM judges this diagnosis malfunction. This malfunction will be caused when either shift solenoid valve A is stuck open or shift solenoid valve B is stuck open.
Gear position supposed by TCM In case of gear position with no malfunctions In case of gear position with shift solenoid valve A stuck open In case of gear position with shift solenoid valve B stuck open *: P0731 is detected. 1 1 2* 4* 2 2 2 3 3 3 3 3 4 4 3 4
AT-128

Description (Contd)
Diagnostic trouble code : A/T 1ST GR FNCTN : P0731 A/T cannot be shifted to the 1st gear position even if electrical circuit is good. Malfunction is detected when ... Check items (Possible cause) Shift solenoid valve A Shift solenoid valve B Each clutch Hydraulic control circuit
GI MA EM LC

CAUTION: Always drive vehicle at a safe speed. Be careful not to rev engine into the red zone on the tachometer. NOTE: If DIAGNOSTIC TROUBLE CODE CONFIRMATION PROCEDURE has been previously conducted, always turn ignition switch OFF and wait at least 5 seconds before conducting the next test. TESTING CONDITION: Always drive vehicle on a level road to improve the accuracy of test. After the repair, perform the following procedure to confirm the malfunction is eliminated. With CONSULT-II 1) Start engine and select DATA MONITOR mode for A/T with CONSULT-II. 2) Make sure that output voltage of A/T fluid temperature sensor is within the range below. FLUID TEMP SEN: 0.4 - 1.5V If out of range, drive the vehicle to decrease the voltage (warm up the fluid) or stop engine to increase the voltage (cool down the fluid). 3) Select 1ST GR FNCTN P0731 of DTC WORK SUPPORT mode for A/T with CONSULT-II and touch START. 4) Accelerate vehicle to 20 to 25 km/h (12 to 16 MPH) under the following condition and release the accelerator pedal completely. THROTTLE POSI: Less than 1.0/8 (at all times during step 4) Selector lever: D position (OD ON) Check that GEAR shows 2 after releasing pedal. 5) Depress accelerator pedal to WOT (more than 7.0/8 of THROTTLE POSI) quickly from a speed of 20 to 25 km/h (12 to 16 MPH) until TESTING changes to STOP VEHICLE or COMPLETED. (It will take approximately 3 seconds.) If the check result NG appears on CONSULT-II screen, go to DIAGNOSTIC PROCEDURE, AT-132. If STOP VEHICLE appears on CONSULT-II screen, go to the following step. Check that GEAR shows 1 when depressing accelerator pedal to WOT. If TESTING does not appear on CONSULT-II for a long time, select SELF-DIAGNOSIS for ENGINE. In case a
EC FE CL MT
SAT014K
SAT971J
SAT021J
AT-129

Description (Contd)
6) 7)
1st trip DTC other than P0731 is shown, refer to applicable TROUBLE DIAGNOSIS FOR DTC. Stop vehicle. Follow the instruction displayed. (Check for normal shifting referring to the table below.)
Gear on actual transmission shift pattern when screen is changed to 1 , 2 , 3 , 4 1,2,3,4 2,2,3,3 4,3,3,4
Vehicle condition No malfunction exists Malfunction for P0731 exists.
8)
Make sure that OK is displayed. (If NG is displayed, refer to DIAGNOSTIC PROCEDURE.) Refer to DIAGNOSTIC PROCEDURE, AT-132. Refer to shift schedule, AT-389. With GST Follow the procedure With CONSULT-II.
AT-130

Wiring Diagram AT 1ST
Wiring Diagram AT 1ST
NCAT0203
TAT227
AT-131

1 CHECK SHIFT SOLENOID VALVE
1. Remove control valve assembly. Refer to AT-280. 2. Check shift solenoid valve operation. Shift solenoid valve A Shift solenoid valve B Refer to Component Inspection, AT-133.
NCAT0044
SAT881JA
OK or NG OK NG GO TO 2. Repair or replace shift solenoid valve assembly.
AT-132

CHECK CONTROL VALVE
1. Disassemble control valve assembly. Refer to Control Valve Assembly, AT-312. 2. Check to ensure that: Valve, sleeve and plug slide along valve bore under their own weight. Valve, sleeve and plug are free from burrs, dents and scratches. Control valve springs are free from damage, deformation and fatigue. Hydraulic line is free from obstacles.
GI MA EM LC EC FE
SAT367H
OK or NG OK NG GO TO 3. Repair control valve assembly.
CL MT
CHECK DTC
Perform Diagnostic Trouble Code (DTC) confirmation procedure, AT-129. OK or NG OK NG INSPECTION END Check control valve again. Repair or replace control valve assembly.
AX SU BR
SHIFT SOLENOID VALVE A AND B
For removal, refer to AT-280.
ST RS
Resistance Check
Check resistance between two terminals.
Solenoid valve Shift solenoid valve A Shift solenoid valve B 2 Ground 1 Terminal No.
NCAT0045S0101
Resistance (Approx.) 20 - 30 5 - 20
BT HA SC EL IDX
SAT050K
AT-133

Component Inspection (Contd)
Operation Check
NCAT0045S0102
Check solenoid valve by listening for its operating sound while applying battery voltage to the terminal and ground.
SAT883JA
AT-134
DTC P0732 A/T 2ND GEAR FUNCTION

Description
Description

NCAT0046
This is an OBD-II self-diagnostic item and not available in TCM self-diagnosis. This malfunction will not be detected while the O/D OFF indicator lamp is indicating another self-diagnosis malfunction. This malfunction is detected when the A/T does not shift into second gear position as instructed by the TCM. This is not caused by electrical malfunction (circuits open or shorted) but by mechanical malfunction such as control valve sticking, improper solenoid valve operation, etc.

Remarks: Specification data are reference values. Terminal No. Wire color Item Condition When shift solenoid valve B operates. (When driving in D1 or D2.) When shift solenoid valve B does not operate. (When driving in D3 or D4.)
NCAT0046S01
12
L/Y
1V or less
AX
NCAT0046S02
This diagnosis monitors actual gear position by checking the torque converter slip ratio calculated by TCM as follows: Torque converter slip ratio = A x C/B A: Output shaft revolution signal from revolution sensor B: Engine speed signal from ECM C: Gear ratio determined as gear position which TCM supposes If the actual gear position is higher than the position (2nd) supposed by TCM, the slip ratio will be more than normal. In case the ratio exceeds the specified value, TCM judges this diagnosis malfunction. This malfunction will be caused when shift solenoid valve B is stuck open.
Gear position supposed by TCM In case of gear position with no malfunctions In case of gear position with shift solenoid valve B stuck open *: P0732 is detected. 1 1 4 2 2 3* 3 3 3 4 4 4
SU BR ST RS BT HA SC
Diagnostic trouble code : A/T 2ND GR FNCTN : P0732
Malfunction is detected when ... A/T cannot be shifted to the 2nd gear position even if electrical circuit is good.
Check items (Possible cause) Shift solenoid valve B Each clutch Hydraulic control circuit
EL IDX
AT-135

Description (Contd)

CAUTION: Always drive vehicle at a safe speed. Be careful not to rev engine into the red zone on the tachometer. NOTE: If DIAGNOSTIC TROUBLE CODE CONFIRMATION PROCEDURE has been previously conducted, always turn ignition switch OFF and wait at least 5 seconds before conducting the next test. TESTING CONDITION: Always drive vehicle on a level road to improve the accuracy of test. After the repair, perform the following procedure to confirm the malfunction is eliminated. With CONSULT-II 1) Start engine and select DATA MONITOR mode for A/T with CONSULT-II. 2) Make sure that output voltage of A/T fluid temperature sensor is within the range below. FLUID TEMP SEN: 0.4 - 1.5V If out of range, drive the vehicle to decrease the voltage (warm up the fluid) or stop engine to increase the voltage (cool down the fluid). 3) Select 2ND GR FNCTN P0732 of DTC WORK SUPPORT mode for A/T with CONSULT-II and touch START. 4) Accelerate vehicle to 53 to 68 km/h (33 to 42 MPH) under the following condition and release the accelerator pedal completely. THROTTLE POSI: Less than 1.0/8 (at all times during step 4) Selector lever: D position (OD ON) Check that GEAR shows 3 or 4 after releasing pedal. 5) Depress accelerator pedal to WOT (more than 7.0/8 of THROTTLE POSI) quickly from a speed of 53 to 68 km/h (33 to 42 MPH) until TESTING changes to STOP VEHICLE or COMPLETED. (It will take approximately 3 seconds.) If the check result NG appears on CONSULT-II screen, go to DIAGNOSTIC PROCEDURE, AT-139. If STOP VEHICLE appears on CONSULT-II screen, go to following step. Check that GEAR shows 2 when depressing accelerator pedal to WOT. If TESTING does not appear on CONSULT-II for a long time, select SELF-DIAGNOSIS for ENGINE. In case a 1st trip DTC other than P0732 is shown, refer to applicable TROUBLE DIAGNOSIS FOR DTC. 6) Stop vehicle. 7) Follow the instruction displayed. (Check for normal shifting referring to the table below.)
Vehicle condition No malfunction exists Malfunction for P0732 exists. Gear on actual transmission shift pattern when screen is changed to 1 , 2 , 3 , 4 1,2,3,4 4,3,3,4
SAT014K
SAT971J
SAT021J
AT-136

Description (Contd)
8)
AT-137

Wiring Diagram AT 2ND
Wiring Diagram AT 2ND
NCAT0204
TAT228
AT-138

1. Remove control valve assembly. Refer to AT-280. 2. Check shift solenoid valve operation. Shift solenoid valve B Refer to Component Inspection, AT-140.
NCAT0047
AX
SAT884JA
SU BR ST RS BT HA SC EL
SAT367H
CHECK CONTROL VALVE
IDX
AT-139

CHECK DTC
SHIFT SOLENOID VALVE B
Resistance Check
Solenoid valve Shift solenoid valve B 1 Terminal No. Ground
NCAT0048S0101
Resistance (Approx.) 5 - 20
SAT051K
Operation Check
NCAT0048S0102
SAT884JA
AT-140
DTC P0733 A/T 3RD GEAR FUNCTION

Description
Description

NCAT0049
This is an OBD-II self-diagnostic item and not available in TCM self-diagnosis. This malfunction will not be detected while the O/D OFF indicator lamp is indicating another self-diagnosis malfunction. This malfunction is detected when the A/T does not shift into third gear position as instructed by the TCM. This is not caused by electrical malfunction (circuits open or shorted) but by mechanical malfunction such as control valve sticking, improper solenoid valve operation, malfunctioning servo piston or brake band, etc.
GI MA EM LC EC FE

Remarks: Specification data are reference values. Terminal No. Wire color Item Condition When shift solenoid valve A operates. (When driving in D1 or D4.) When shift solenoid valve A does not operate. (When driving in D2 or D3.)
NCAT0049S01
CL MT
11
L/W
0V
AX
NCAT0049S02
This diagnosis monitors actual gear position by checking the torque converter slip ratio calculated by TCM as follows: Torque converter slip ratio = A x C/B A: Output shaft revolution signal from revolution sensor B: Engine speed signal from ECM C: Gear ratio determined as gear position which TCM supposes If the actual gear position is higher than the position (3rd) supposed by TCM, the slip ratio will be more than normal. In case the ratio exceeds the specified value, TCM judges this diagnosis malfunction. This malfunction will be caused when shift solenoid valve A is stuck closed.
Gear position supposed by TCM In case of gear position with no malfunctions In case of gear position with shift solenoid valve A stuck closed *: P0733 is detected. Diagnostic trouble code : A/T 3RD GR FNCTN : P0733 Malfunction is detected when ... A/T cannot be shifted to the 3rd gear position even if electrical circuit is good. Check items (Possible cause) Shift solenoid valve A Each clutch Hydraulic control circuit 1 1 1 2 2 1 3 3 4* 4 4 4
AT-141

Description (Contd)

CAUTION: Always drive vehicle at a safe speed. Be careful not to rev engine into the red zone on the tachometer. NOTE: If DIAGNOSTIC TROUBLE CODE CONFIRMATION PROCEDURE has been previously conducted, always turn ignition switch OFF and wait at least 5 seconds before conducting the next test. TESTING CONDITION: Always drive vehicle on a level road to improve the accuracy of test. After the repair, perform the following procedure to confirm the malfunction is eliminated. With CONSULT-II 1) Start engine and select DATA MONITOR mode for A/T with CONSULT-II. 2) Make sure that output voltage of A/T fluid temperature sensor is within the range below. FLUID TEMP SEN: 0.4 - 1.5V If out of range, drive the vehicle to decrease the voltage (warm up the fluid) or stop engine to increase the voltage (cool down the fluid). 3) Select 3RD GR FNCTN P0733 of DTC WORK SUPPORT mode for A/T with CONSULT-II and touch START. 4) Accelerate vehicle to 80 to 95 km/h (50 to 59 MPH) under the following condition and release the accelerator pedal completely. THROTTLE POSI: Less than 1.0/8 (at all times during step 4) Selector lever: D position (OD ON) Check that GEAR shows 4 after releasing pedal. 5) Depress accelerator pedal steadily with 3.5/8 - 4.5/8 of THROTTLE POSI from a speed of 80 to 95 km/h (50 to 59 MPH) until TESTING changes to STOP VEHICLE or COMPLETED. (It will take approximately 3 seconds.) If the check result NG appears on CONSULT-II screen, go to DIAGNOSTIC PROCEDURE, AT-145. If STOP VEHICLE appears on CONSULT-II screen, go to following step. Check that GEAR shows 3 when depressing accelerator pedal with 3.5/8 - 4.5/8 of THROTTLE POSI. If TESTING does not appear on CONSULT-II for a long time, select SELF-DIAGNOSIS for ENGINE. In case a 1st trip DTC other than P0733 is shown, refer to applicable TROUBLE DIAGNOSIS FOR DTC. 6) Stop vehicle. 7) Follow the instruction displayed. (Check for normal shifting referring to the table below.)
Vehicle condition No malfunction exists. Malfunction for P0733 exists. Gear on actual transmission shift pattern when screen is changed to 1 , 2 , 3 , 4 1,2,3,4 1,1,4,4
SAT014K
SAT971J
SAT021J
AT-142

Description (Contd)
8)
AT-143

Wiring Diagram AT 3RD
Wiring Diagram AT 3RD
NCAT0205
TAT229
AT-144

1. Remove control valve assembly. Refer to AT-280. 2. Check shift solenoid valve operation. Shift solenoid valve A Refer to Component Inspection below.
NCAT0050
AX
SAT886JA
SAT367H
CHECK CONTROL VALVE
IDX
AT-145

CHECK DTC
SHIFT SOLENOID VALVE A
Resistance Check
Solenoid valve Shift solenoid valve A 2 Terminal No. Ground
NCAT0051S0101
SAT052K
Operation Check
NCAT0051S0102
SAT886JA
AT-146
DTC P0734 A/T 4TH GEAR FUNCTION

Description
Description

NCAT0052
This is an OBD-II self-diagnostic item and not available in TCM self-diagnosis. This malfunction will not be detected while the O/D OFF indicator lamp is indicating another self-diagnosis malfunction. This malfunction is detected when the A/T does not shift into fourth gear position or the torque converter clutch does not lock up as instructed by the TCM. This is not caused by electrical malfunction (circuits open or shorted) but by mechanical malfunction such as control valve sticking, improper solenoid valve operation, malfunctioning oil pump or torque converter clutch, etc.
GI MA EM LC EC FE
CONSULT-II REFERENCE VALUE IN DATA MONITOR MODE CL NCAT0052S01

Remarks: Specification data are reference values. Monitor item Condition Small throttle opening (Low line pressure) " Large throttle opening (High line pressure) Specification Approximately 24% " Approximately 95%
MT
Line pressure solenoid valve duty

Remarks: Specification data are reference values. Terminal No. Wire color Item Condition When releasing accelerator pedal after warming up engine. When depressing accelerator pedal fully after warming up engine. When releasing accelerator pedal after warming up engine. When depressing accelerator pedal fully after warming up engine. When shift solenoid valve A operates. (When driving in D1 or D4.) When shift solenoid valve A does not operate. (When driving in D2 or D3.) When shift solenoid valve B operates. (When driving in D1 or D2.) When shift solenoid valve B does not operate. (When driving in D3 or D4.)
AX
NCAT0052S02
Judgement standard (Approx.) 1.5 - 2.5V
SU BR ST
R/W
0V 5 - 14V 0V
P/B
RS BT HA SC EL
Battery voltage
11
L/W
0V
Battery voltage
12
L/Y
IDX
0V
AT-147

Description (Contd)
NCAT0052S03
This diagnosis monitors actual gear position by checking the torque converter slip ratio calculated by TCM as follows: Torque converter slip ratio = A x C/B A: Output shaft revolution signal from revolution sensor B: Engine speed signal from ECM C: Gear ratio determined as gear position which TCM supposes If the actual gear position is much lower than the position (4th) supposed by TCM, the slip ratio will be much less than normal. In case the ratio does not reach the specified value, TCM judges this diagnosis malfunction. This malfunction will be caused when shift solenoid valve B is stuck closed.
Gear position supposed by TCM In case of gear position with no malfunctions In case of gear position with shift solenoid valve B stuck closed *: P0734 is detected. Diagnostic trouble code : A/T 4TH GR FNCTN A/T cannot be shifted to the 4th gear position even if electrical circuit is good. Malfunction is detected when ... Check items (Possible cause) Shift solenoid valve A Shift solenoid valve B Line pressure solenoid valve Each clutch Hydraulic control circuit 1 1 1 2 2 2 3 3 2 4 4 1*
: P0734
AT-148

Description (Contd)

CAUTION: Always drive vehicle at a safe speed. If conducting this DTC CONFIRMATION PROCEDURE again, always turn ignition switch OFF and wait at least 5 seconds before continuing. Be careful not to rev engine into the red zone on the tachometer. NOTE: If DIAGNOSTIC TROUBLE CODE CONFIRMATION PROCEDURE has been previously conducted, always turn ignition switch OFF and wait at least 5 seconds before conducting the next test. TESTING CONDITION: Always drive vehicle on a level road to improve the accuracy of test. After the repair, perform the following procedure to confirm the malfunction is eliminated. With CONSULT-II 1) Start engine and select DATA MONITOR mode for A/T with CONSULT-II. 2) Make sure that output voltage of A/T fluid temperature sensor is within the range below. FLUID TEMP SEN: 0.4 - 1.5V If out of range, drive the vehicle to decrease the voltage (warm up the fluid) or stop engine to increase the voltage (cool down the fluid). 3) Select 4TH GR FNCTN P0734 of DTC WORK SUPPORT mode for A/T with CONSULT-II and touch START. 4) Accelerate vehicle to 50 to 60 km/h (31 to 37 MPH) under the following condition and release the accelerator pedal completely. THROTTLE POSI: Less than 5.5/8 (at all times during step 4) Selector lever: D position (OD ON) Check that GEAR shows 3 after releasing pedal. 5) Depress accelerator pedal steadily with 1.0/8 - 2.0/8 of THROTTLE POSI from a speed of 50 to 60 km/h (31 to 37 MPH) until TESTING has turned to STOP VEHICLE or COMPLETED. (It will take approximately 3 seconds.) If the check result NG appears on CONSULT-II screen, go to DIAGNOSTIC PROCEDURE, AT-152. If STOP VEHICLE appears on CONSULT-II screen, go to following step. Check that GEAR shows 4 when depressing accelerator pedal with 1.0/8 - 2.0/8 of THROTTLE POSI. If TESTING does not appear on CONSULT-II for a long time, select SELF-DIAGNOSIS for ENGINE. In case a 1st trip DTC other than P0734 is shown, refer to applicable TROUBLE DIAGNOSIS FOR DTC. 6) Stop vehicle. 7) Follow the instruction displayed. (Check for normal shifting referring to the table below.)
SAT014K
SAT971J
SAT021J
AT-149

Description (Contd)
Vehicle condition No malfunction exists Malfunction for P0734 exists. Gear on actual transmission shift pattern when screen is changed to 1 , 2 , 3 , 4 1,2,3,4 1,2,2,1
8)
AT-150

Wiring Diagram AT 4TH
Wiring Diagram AT 4TH
NCAT0206
TAT230
AT-151

1 CHECK SHIFT UP (D3 TO D4)
During Cruise test Part 1 (AT-76), does A/T shift from D3 to D4 at the specified speed?
NCAT0053
SAT988H
Yes or No Yes No GO TO 9. GO TO 2.
CHECK LINE PRESSURE
Perform line pressure test. Refer to AT-66.
MTBL0388
AT-152

CHECK SOLENOID VALVES
1. Remove control valve assembly. Refer to AT-280. 2. Refer to Component Inspection, AT-156.
SAT847JA
OK or NG OK NG GO TO 4. Replace solenoid valve assembly.
AX SU BR ST RS BT HA SC EL
SAT367H
CHECK CONTROL VALVE
1. Disassemble control valve assembly. Refer to AT-312. 2. Check to ensure that: Valve, sleeve and plug slide along valve bore under their own weight. Valve, sleeve and plug are free from burrs, dents and scratches. Control valve springs are free from damage, deformation and fatigue. Hydraulic line is free from obstacles.
OK or NG OK NG GO TO 5. Repair control valve.
IDX
AT-153


OK or NG
Does A/T shift from D3 to D4 at the specified speed?
OK NG
GO TO 9. Check control valve again. Repair or replace control valve assembly.
CHECK LINE PRESSURE SOLENOID VALVE
1. Remove control valve assembly. Refer to AT-280. 2. Refer to Component Inspection, AT-156.
SAT888J
AT-154

CHECK CONTROL VALVE
1. Disassemble control valve assembly. Refer to AT-312. 2. Check line pressure circuit valves for sticking. Pressure regulator valve Pilot valve Pressure modifier valve
GI MA EM LC EC FE
SAT367H
CL MT

Yes or No
AX SU BR
Yes No
CHECK DTC
Perform Diagnostic Trouble Code (DTC) confirmation procedure, AT-149. OK or NG OK NG INSPECTION END Perform Cruise test Part 1 again and return to the start point of this test group.
AT-155

SOLENOID VALVES
Resistance Check
Solenoid valve Shift solenoid valve A Shift solenoid valve B Line pressure solenoid valve 2 1 4 Ground Terminal No.
NCAT0054S0101
Resistance (Approx.) 20 - 30 5 - 20 2.5 - 5
SAT848JA
Operation Check
NCAT0054S0102
SAT847JA
AT-156
DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE

Description
Description
NCAT0055
The torque converter clutch solenoid valve is activated, with the gear in D4, by the TCM in response to signals sent from the vehicle speed and throttle position sensors. Lock-up piston operation will then be controlled. Lock-up operation, however, is prohibited when A/T fluid temperature is too low. When the accelerator pedal is depressed (less than 2/8) in lock-up condition, the engine speed should not change abruptly. If there is a big jump in engine speed, there is no lock-up.
SAT283HB
GI MA EM LC

Remarks: Specification data are reference values. Monitor item Torque converter clutch solenoid valve duty Condition Lock-up OFF " Lock-up ON Specification Approximately 4% " Approximately 94%
EC FE CL

NCAT0055S02
MT
Judgement standard (Approx.) 8 - 15V
GY/R
When A/T performs lock-up. When A/T does not perform lockup.
AX SU
NCAT0055S03
0V

Diagnostic trouble code : TCC SOLENOID/CIRC : P0740 Malfunction is detected when ... TCM detects an improper voltage drop when it tries to operate the solenoid valve. Check items (Possible cause)
Harness or connectors (The solenoid circuit is open or shorted.) T/C clutch solenoid valve
AT-157

Description (Contd)

NOTE: If DIAGNOSTIC TROUBLE CODE CONFIRMATION PROCEDURE has been previously conducted, always turn ignition switch OFF and wait at least 5 seconds before conducting the next test. After the repair, perform the following procedure to confirm the malfunction is eliminated. With CONSULT-II 1) Turn ignition switch ON. 2) Select DATA MONITOR mode for ENGINE with CONSULT-II and wait at least 1 second. With GST Follow the procedure With CONSULT-II.
SAT014K
SEF949Y
AT-158

Wiring Diagram AT TCV
Wiring Diagram AT TCV
NCAT0207
TAT231
AT-159

1 CHECK VALVE RESISTANCE
1. Turn ignition switch to OFF position. 2. Disconnect terminal cord assembly connector in engine compartment. 3. Check resistance between terminal 5 and ground. Resistance: 10 - 20
NCAT0056
SAT889J
OK or NG OK NG GO TO 2. 1. Remove oil pan. Refer to AT-280. 2. Check the following items: Torque converter clutch solenoid valve Refer to Component Inspection, AT-162. Harness of terminal cord assembly for short or open
AT-160

CHECK POWER SOURCE CIRCUIT
1. Turn ignition switch to OFF position. 2. Disconnect TCM harness connector. 3. Check continuity between terminal 5 and TCM harness connector terminal 3. Continuity should exist.
SAT890J
If OK, check harness for short to ground and short to power. 4. Reinstall any part removed. OK or NG OK NG GO TO 3. Repair open circuit or short to ground or short to power in harness or connectors.
AX SU BR ST
CHECK DTC
RS BT HA SC EL IDX
AT-161

NCAT0057
TORQUE CONVERTER CLUTCH SOLENOID VALVE NCAT0057S01 Resistance Check

Solenoid valve Torque converter clutch solenoid valve Terminal No. Resistance (Approx.) Ground 5 - 20
NCAT0057S0101
SAT053K
Operation Check
NCAT0057S0102
SAT054K
AT-162
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)

Description
Description

NCAT0058
This is an OBD-II self-diagnostic item and not available in TCM self-diagnosis. This malfunction will not be detected while the O/D OFF indicator lamp is indicating another self-diagnosis malfunction. This malfunction is detected when the A/T does not shift into fourth gear position or the torque converter clutch does not lock up as instructed by the TCM. This is not caused by electrical malfunction (circuits open or shorted) but by mechanical malfunction such as control valve sticking, improper solenoid valve operation, malfunctioning oil pump or torque converter clutch, etc.
GI MA EM LC
CONSULT-II REFERENCE VALUE IN DATA MONITOR EC MODE NCAT0058S01

Remarks: Specification data are reference values. Monitor item Torque converter clutch solenoid valve duty Condition Lock-up OFF " Lock-up ON Specification Approximately 4% " Approximately 94%
FE CL
NCAT0058S02

Remarks: Specification data are reference values. Terminal No. Wire color Item Condition When releasing accelerator pedal after warming up engine. When depressing accelerator pedal fully after warming up engine. When releasing accelerator pedal after warming up engine. When depressing accelerator pedal fully after warming up engine. When A/T performs lock-up.
MT
Judgement standard (Approx.) 1.5 - 2.5V 0V 5 - 14V 0V
AX SU BR ST
R/W
P/B
GY/R
8 - 15V
RS
When A/T does not perform lock-up. 0V
BT HA SC EL IDX
AT-163

Description (Contd)
=NCAT0058S03
This diagnosis monitors actual gear position by checking the torque converter slip ratio calculated by TCM as follows: Torque converter slip ratio = A x C/B A: Output shaft revolution signal from revolution sensor B: Engine speed signal from ECM C: Gear ratio determined as gear position which TCM supposes If the actual gear position is much lower than the position (4th) supposed by TCM, the slip ratio will be much less than normal. In case the ratio does not reach the specified value, TCM judges this diagnosis malfunction. This malfunction will be caused when shift solenoid valve B is stuck closed.
Gear position supposed by TCM In case of gear position with no malfunctions In case of gear position with shift solenoid valve B stuck closed *: P0744 is detected. Diagnostic trouble code : A/T TCC S/V FNCTN : P0744 A/T cannot perform lock-up even if electrical circuit is good. Malfunction is detected when ... Check items (Possible cause) Torque converter clutch solenoid valve Line pressure solenoid valve Each clutch Hydraulic control circuit 1 1 1 2 2 2 3 3 2 4 4 1*

CAUTION: Always drive vehicle at a safe speed. NOTE: If DIAGNOSTIC TROUBLE CODE CONFIRMATION PROCEDURE has been previously conducted, always turn ignition switch OFF and wait at least 5 seconds before conducting the next test. After the repair, perform the following procedure to confirm the malfunction is eliminated. With CONSULT-II 1) Start engine and select DATA MONITOR mode for A/T with CONSULT-II. 2) Make sure that output voltage of A/T fluid temperature sensor is within the range below. FLUID TEMP SEN: 0.4 - 1.5V If out of range, drive the vehicle to decrease the voltage (warm up the fluid) or stop engine to increase the voltage (cool down the fluid). 3) Select TCC S/V FNCTN P0744 of DTC WORK SUPPORT mode for A/T with CONSULT-II and touch START.
SAT014K
SAT971J
AT-164

Description (Contd)
4)
SAT021J
Accelerate vehicle to more than 80 km/h (50 MPH) and maintain the following condition continuously until TESTING has turned to COMPLETE. (It will take approximately 30 seconds after TESTING shows.) THROTTLE POSI: 1.0/8 - 2.0/8 (at all times during step 4) Selector lever: D position (OD ON) TCC S/V DUTY: More than 94% VHCL/S SEA/T: Constant speed of more than 80 km/h (50 MPH) Check that GEAR shows 4. For shift schedule, refer to SDS, AT-389. If TESTING does not appear on CONSULT-II for a long time, select SELF-DIAGNOSIS. In case a 1st trip DTC other than P0744 is shown, refer to applicable TROUBLE DIAGNOSIS FOR DTC. 5) Make sure that OK is displayed. (If NG is displayed, refer to DIAGNOSTIC PROCEDURE.) Refer to DIAGNOSTIC PROCEDURE, AT-167. Refer to shift schedule, AT-389. With GST Follow the procedure With CONSULT-II.
AT-165

Wiring Diagram AT TCCSIG
Wiring Diagram AT TCCSIG
NCAT0208
TAT232
AT-166

1 CHECK SHIFT UP (D3 TO D4)
During Cruise test Part 1 (AT-76), does A/T shift from D3 to D4 at the specified speed?
NCAT0059
GI MA EM LC EC
SAT988H
Yes or No Yes No GO TO 10. GO TO 2.
FE CL MT
CHECK LINE PRESSURE
Perform line pressure test. Refer to AT-66.
AX
MTBL0388
AT-167

CHECK CONTROL VALVE
1. Disassemble control valve assembly. Refer to AT-312. 2. Check to ensure that: Valve, sleeve and plug slide along valve bore under their own weight. Valve, sleeve and plug are free from burrs, dents and scratches. Control valve springs are free from damage, deformation and fatigue. Hydraulic line is free from obstacles.
SAT367H

Yes or No
Yes No
CHECK DTC
Perform Diagnostic Trouble Code (DTC) confirmation procedure, AT-164. OK or NG OK NG INSPECTION END GO TO 10.. CHECK LOCK-UP CONDITION.
AT-168

CHECK LINE PRESSURE SOLENOID VALVE
1. Remove control valve assembly. Refer to AT-280. 2. Check line pressure solenoid valve operation. Refer to AT-173.
SAT893J
AX SU BR
CHECK CONTROL VALVE
1. Disassemble control valve assembly. Refer to AT-312. 2. Check line pressure circuit valves for sticking. Pressure regulator valve Pilot valve Pressure modifier valve
ST RS BT HA SC EL
SAT367H
IDX
AT-169


Yes or No
Yes No
CHECK DTC
Perform Diagnostic Trouble Code (DTC) confirmation procedure, AT-164. OK or NG OK NG INSPECTION END GO TO 10. And check for proper lock-up.
10
CHECK LOCK-UP CONDITION
During Cruise test Part 1 (AT-76), does A/T perform lock-up at the specified speed?
SAT989H
Yes or No Yes No Perform Cruise test Part 1 again and return to the start point of this test group. GO TO 11.
AT-170

11
CHECK TORQUE CONVERTER CLUTCH SOLENOID VALVE
1. Remove control valve assembly. Refer to AT-280. 2. Check torque converter clutch solenoid valve operation. Refer to AT-173.
SAT055K
AX SU BR ST RS BT HA SC
SAT367H
12
CHECK CONTROL VALVE
1. Disassemble control valve assembly. Refer to AT-312. 2. Check control valves for sticking. Torque converter clutch control valve Torque converter clutch relief valve
EL IDX
AT-171

13
CHECK LOCK-UP CONDITION
Does A/T perform lock-up at the specified speed? Yes or No Yes No GO TO 14. Check control valve again. Repair or replace control valve assembly.
14
CHECK DTC
Perform Diagnostic Trouble Code (DTC) confirmation procedure, AT-164. OK or NG OK NG INSPECTION END Perform Cruise test Part 1 again and return to the start point of this test group.
AT-172

SOLENOID VALVES
Resistance Check
Solenoid valve Line pressure solenoid valve Torque converter clutch solenoid valve 4 Ground 5 Terminal No.
NCAT0060S0101
Resistance (Approx.) 2.5 - 5
5 - 20
SAT849JA
MT
Operation Check
NCAT0060S0102
SAT850JA
SC EL IDX
AT-173
DTC P0745 LINE PRESSURE SOLENOID VALVE

Description
Description
NCAT0061
The line pressure solenoid valve regulates the oil pump discharge pressure to suit the driving condition in response to a signal sent from the TCM. The line pressure duty cycle value is not consistent when the closed throttle position switch is ON. To confirm the line pressure duty cycle at low pressure, the accelerator (throttle) should be open until the closed throttle position switch is OFF.
SAT283HB

Remarks: Specification data are reference values. Monitor item Condition Small throttle opening (Low line pressure) " Large throttle opening (High line pressure) Specification Approximately 24% " Approximately 95%
Line pressure solenoid valve duty
NOTE: The line pressure duty cycle value is not consistent when the closed throttle position switch is ON. To confirm the line pressure duty cycle at low pressure, the accelerator (throttle) should be open until the closed throttle position switch is OFF.

Remarks: Specification data are reference values. Terminal No. Wire color Item Condition When releasing accelerator pedal after warming up engine. When depressing accelerator pedal fully after warming up engine. When releasing accelerator pedal after warming up engine. When depressing accelerator pedal fully after warming up engine.
NCAT0061S02
Judgement standard (Approx.) 1.5 - 2.5V 0V 5 - 14V 0V
R/W
P/B

Diagnostic trouble code : L/PRESS SOL/CIRC : P0745 Malfunction is detected when ... TCM detects an improper voltage drop when it tries to operate the solenoid valve. Check items (Possible cause)
NCAT0061S03
Harness or connectors (The solenoid circuit is open or shorted.) Line pressure solenoid valve
AT-174

Description (Contd)

NOTE: If DIAGNOSTIC TROUBLE CODE CONFIRMATION PROCEDURE has been previously conducted, always turn ignition switch OFF and wait at least 5 seconds before conducting the next test. After the repair, perform the following procedure to confirm the malfunction is eliminated. With CONSULT-II 1) Turn ignition switch ON and select DATA MONITOR mode for ENGINE with CONSULT-II. 2) Depress accelerator pedal completely and wait at least 1 second. With GST Follow the procedure With CONSULT-II.
SAT014K
SEF949Y
MT
AT-175

Wiring Diagram AT LPSV
Wiring Diagram AT LPSV
NCAT0209
TAT233
AT-176

1. Turn ignition switch to OFF position. 2. Disconnect terminal cord assembly connector in engine compartment. 3. Check resistance between terminal 4 and ground. Resistance: 2.5 - 5
NCAT0062
GI MA EM LC EC FE
SAT895J
OK or NG OK NG GO TO 2. 1. Remove control valve assembly. Refer to AT-280. 2. Check the following items: Line pressure solenoid valve Refer to Component Inspection, AT-180. Harness of terminal cord assembly for short or open
CL MT
AT-177

1. Turn ignition switch to OFF position. 2. Disconnect TCM harness connector. 3. Check resistance between terminal 4 and TCM harness connector terminal 2. Resistance: 10 - 15
SAT896J
OK or NG OK NG GO TO 3. Check the following items: Dropping resistor Refer to Component Inspection, AT-180. Harness for short or open between TCM terminal 2 and terminal cord assembly (Main harness)
AT-178

1. Turn ignition switch to OFF position. 2. Check resistance between terminal 4 and TCM harness connector terminal 1. Resistance: Approx. 0
SAT897J
AX SU BR ST
CHECK DTC
RS BT HA SC EL IDX
AT-179

LINE PRESSURE SOLENOID VALVE
Resistance Check
Solenoid valve Line pressure solenoid valve 4 Terminal No. Ground
NCAT0063S0101
Resistance (Approx.) 2.5 - 5
SAT898J
Operation Check
NCAT0063S0102
SAT899J
DROPPING RESISTOR
Check resistance between two terminals. Resistance: 10 - 15
NCAT0063S02
SAT444J
AT-180
DTC P0750 SHIFT SOLENOID VALVE A

Description
Description
NCAT0064
Shift solenoid valves A and B are turned ON or OFF by the TCM in response to signals sent from the PNP switch, vehicle speed and throttle position sensors. Gears will then be shifted to the optimum position.
GI MA EM
SAT283HB
LC
EC FE CL

Remarks: Specification data are reference values. Terminal No. Wire color Item Condition When shift solenoid valve A operates. (When driving in D1 or D4.) When shift solenoid valve A does not operate. (When driving in D2 or D3.)
NCAT0064S01
MT
11
L/W
0V
AX
NCAT0064S02

Diagnostic trouble code : SFT SOL A/CIRC : P0750 Malfunction is detected when ... TCM detects an improper voltage drop when it tries to operate the solenoid valve. Check items (Possible cause)
Harness or connectors (The solenoid circuit is open or shorted.) Shift solenoid valve A
AT-181

Description (Contd)

CAUTION: Always drive vehicle at a safe speed. NOTE: If DIAGNOSTIC TROUBLE CODE CONFIRMATION PROCEDURE has been previously conducted, always turn ignition switch OFF and wait at least 5 seconds before conducting the next test. After the repair, perform the following procedure to confirm the malfunction is eliminated. With CONSULT-II 1) Turn ignition switch ON and select DATA MONITOR mode for ENGINE with CONSULT-II. 2) Start engine. 3) Drive vehicle in D position and allow the transmission to shift 1 , 2 (GEAR). With GST Follow the procedure With CONSULT-II.
SAT014K
SEF949Y
AT-182

Wiring Diagram AT SSV/A
Wiring Diagram AT SSV/A
NCAT0210
TAT234
AT-183

NCAT0065
SAT900J
OK or NG OK NG GO TO 2. 1. Remove control valve assembly. Refer to AT-280. 2. Check the following items: Shift solenoid valve A Refer to Component Inspection, AT-186. Harness of terminal cord assembly for short or open
AT-184

SAT901J
AX SU BR ST
CHECK DTC
RS BT HA SC EL IDX
AT-185

SHIFT SOLENOID VALVE A
Resistance Check
Solenoid valve Shift solenoid valve A 2 Terminal No. Ground
NCAT0066S0101
SAT056K
Operation Check
NCAT0066S0102
SAT903JA
AT-186
DTC P0755 SHIFT SOLENOID VALVE B

Description
Description
NCAT0067
Shift solenoid valves A and B are turned ON or OFF by the TCM in response to signals sent from the PNP switch, vehicle speed and throttle position sensors. Gears will then be shifted to the optimum position.
GI MA EM
SAT283HB
LC
EC FE CL

Remarks: Specification data are reference values. Terminal No. Wire color Item Condition When shift solenoid valve B operates. (When driving in D1 or D2.) When shift solenoid valve B does not operate. (When driving in D3 or D4.)
NCAT0067S01
Judgement standard
MT
Battery voltage
12
L/Y
1V or less
AX
NCAT0067S02

Diagnostic trouble code : SFT SOL B/CIRC : P0755 Malfunction is detected when ... TCM detects an improper voltage drop when it tries to operate the solenoid valve. Check items (Possible cause)
Harness or connectors (The solenoid circuit is open or shorted.) Shift solenoid valve B
AT-187

Description (Contd)

CAUTION: Always drive vehicle at a safe speed. NOTE: If DIAGNOSTIC TROUBLE CODE CONFIRMATION PROCEDURE has been previously conducted, always turn ignition switch OFF and wait at least 5 seconds before conducting the next test. After the repair, perform the following procedure to confirm the malfunction is eliminated. With CONSULT-II 1) Turn ignition switch ON and select DATA MONITOR mode for ENGINE with CONSULT-II. 2) Start engine. 3) Drive vehicle in D position and allow the transmission to shift 1 , 2 , 3 (GEAR). With GST Follow the procedure With CONSULT-II.
SAT014K
SEF949Y
AT-188

Wiring Diagram AT SSV/B
Wiring Diagram AT SSV/B
NCAT0211
TAT235
AT-189

NCAT0068
SAT904J
OK or NG OK NG GO TO 2. 1. Remove control valve assembly. Refer to AT-280. 2. Check the following items: Shift solenoid valve B Refer to Component Inspection, AT-192. Harness of terminal cord assembly for short or open
AT-190

SAT905J
AX SU BR ST
CHECK DTC
RS BT HA SC EL IDX
AT-191

SHIFT SOLENOID VALVE B
Resistance Check
Solenoid valve Shift solenoid valve B 1 Terminal No. Ground
NCAT0069S0101
SAT057K
Operation Check
NCAT0069S0102
SAT907JA
AT-192
DTC P1705 THROTTLE POSITION SENSOR

Description
Description

NCAT0070
SAT413J
Throttle position sensor The throttle position sensor detects the throttle valve position and sends a signal to the TCM. Throttle position switch Consists of a wide open throttle position switch and a closed throttle position switch. The wide open throttle position switch sends a signal to the TCM when the throttle valve is open at least 1/2 of the full throttle position. The closed throttle position switch sends a signal to the TCM when the throttle valve is fully closed.

Remarks: Specification data are reference values. Monitor item Throttle position sensor Fully-open throttle Approximately 4V Condition Fully-closed throttle Specification Approximately 0.5V

NCAT0070S02
MT
16
Closed throttle position switch (in throttle position switch)
When releasing accelerator pedal after warming up engine. Refer to Preparation, TCM SELF- Battery voltage DIAGNOSTIC PROCEDURE (No Tools), AT-49. When depressing accelerator pedal after warming up engine. Refer to Preparation, TCM SELF- 0V DIAGNOSTIC PROCEDURE (No Tools), AT-49. When depressing accelerator pedal more than half-way after warming up engine. When releasing accelerator pedal after warming up engine. Ignition switch ON. Ignition switch OFF. Battery voltage
AX SU BR ST RS
17
LG
Wide open throttle position switch (in throttle position switch) Throttle position sensor (Power source)
0V 4.5 - 5.5V 0V
BT HA SC EL
32
P/L
41
GY
Fully-closed When depressing accelerator pedal throttle: 0.5V slowly after warming up engine. (Voltage rises gradually in response Fully-open throttle: to throttle position.) 4V
42
Ground (Throttle position sensor)
IDX
AT-193

Description (Contd)

Diagnostic trouble code : TP SEN/CIRC A/T : P1705 Malfunction is detected when ... TCM receives an excessively low or high voltage from the sensor. Check items (Possible cause)
NCAT0070S03
Harness or connectors (The sensor circuit is open or shorted.) Throttle position sensor Throttle position switch

CAUTION: Always drive vehicle at a safe speed. NOTE: If DIAGNOSTIC TROUBLE CODE CONFIRMATION PROCEDURE has been previously conducted, always turn ignition switch OFF and wait at least 5 seconds before conducting the next test. After the repair, perform the following procedure to confirm the malfunction is eliminated. With CONSULT-II 1) Apply vacuum to the throttle opener, then check the following. Refer to steps from 1 to 5 of Preparation, TCM SELF-DIAGNOSTIC PROCEDURE (No Tools), AT-49. 2) Turn ignition switch ON and select TCM INPUT SIGNALS in DATA MONITOR mode for A/T with CONSULT-II. 3) Check the following.
Accelerator pedal condition
SAT971J
SAT014K
THRTL POS SEN CLOSED THL/SW Less than 4.7V 0.1 - 4.6V 1.9 - 4.6V ON OFF OFF
W/O THRL/PSW OFF OFF ON
Fully released Partially depressed Fully depressed
4) 5)
SAT014K
6)
SEF949Y
If the check result is NG, go to DIAGNOSTIC PROCEDURE, AT-197. If the check result is OK, go to following step. Turn ignition switch ON and select DATA MONITOR mode for ENGINE with CONSULT-II. Start engine and maintain the following conditions for at least 3 consecutive seconds. Then release accelerator pedal completely. VHCL SPEED SE: 10 km/h (6 MPH) or more THRTL POS SEN: Approximately 3V or less Selector lever: D position (OD ON) If the check result is NG, go to DIAGNOSTIC PROCEDURE, AT-197. If the check result is OK, go to following step. Maintain the following conditions for at least 3 consecutive seconds. Then release accelerator pedal completely. VHCL SPEED SE: 10 km/h (6 MPH) or more Accelerator pedal: Wide open throttle Selector lever: D position (OD ON)
AT-194

Description (Contd)
With GST Follow the procedure With CONSULT-II.
AT-195

Wiring Diagram AT TPS
Wiring Diagram AT TPS
NCAT0212
TAT236
AT-196

1 CHECK DTC WITH ECM
Perform diagnostic test mode II (self-diagnostic results) for engine control. Refer to EC-81, Malfunction Indicator Lamp (MIL). OK or NG OK (With CONSULT-II) OK (Without CONSULTII) NG GO TO 2. GO TO 3.
NCAT0071
Check throttle position sensor circuit for engine control. Refer to EC-177, DTC P0120 THROTTLE POSITION SENSOR.
CHECK INPUT SIGNAL (WITH CONSULT-II)
With CONSULT-II 1. Apply vacuum to the throttle opener then check the following. Refer from step 1 to 5 of Preparation, TCM SELF-DIAGNOSTIC PROCEDURE (No Tools), AT-49. 2. Turn ignition switch to ON position. (Do not start engine.) 3. Select TCM INPUT SIGNALS in DATA MONITOR mode for A/T with CONSULT-II.
AX SU
SAT014K
4. Read out the value of THRTL POS SEN. Voltage: Fully-closed throttle: Approximately 0.5V Fully-open throttle: Approximately 4V
BR ST RS BT HA SC
SAT614J
OK or NG OK NG GO TO 4. Check harness for short or open between ECM and TCM regarding throttle position sensor circuit. (Main harness)
EL IDX
AT-197

CHECK INPUT SIGNAL (WITHOUT CONSULT-II)
Without CONSULT-II 1. Apply vacuum to the throttle opener then check the following. Refer to steps 1 to 5 of Preparation, TCM SELF-DIAGNOSTIC PROCEDURE (No Tools), AT-49. 2. Turn ignition switch to ON position. (Do not start engine.) 3. Check voltage between TCM terminals 41 and 42 while accelerator pedal is depressed slowly. Voltage: Fully-closed throttle valve: Approximately 0.5V Fully-open throttle valve: Approximately 4V (Voltage rises gradually in response to throttle position)
SAT453J
OK or NG OK NG GO TO 5. Check harness for short or open between ECM and TCM regarding throttle position sensor circuit. (Main harness)
AT-198

CHECK THROTTLE POSITION SWITCH CIRCUIT (WITH CONSULT-II)
With CONSULT-II 1. Apply vacuum to the throttle opener, then check the following. Refer to steps 1 to 5 of Preparation, TCM SELF-DIAGNOSTIC PROCEDURE (No Tools), AT-49. 2. Turn ignition switch to ON position. (Do not start engine.) 3. Select TCM INPUT SIGNALS in DATA MONITOR mode for A/T with CONSULT-II. 4. Read out CLOSED THL/SW and W/O THRL/P-SW depressing and releasing accelerator pedal. Check the signal of throttle position switch is indicated properly.
GI MA EM LC EC
MTBL0011
FE CL MT
SAT702J
OK or NG OK NG GO TO 6. Check the following items: Throttle position switch Refer to Components Inspection, AT-201. Harness for short or open between ignition switch and throttle position switch (Main harness) Harness for short or open between throttle position switch and TCM (Main harness)
AT-199

CHECK THROTTLE POSITION SWITCH CIRCUIT (WITHOUT CONSULT-II)
Without CONSULT-II 1. Apply vacuum to the throttle opener, then check the following. Refer to steps 1 to 5 of Preparation, TCM SELF-DIAGNOSTIC PROCEDURE (No Tools), AT-49. 2. Turn ignition switch to ON position. (Do not start engine.) 3. Check voltage between TCM terminals 16, 17 and ground while depressing, and releasing accelerator pedal slowly. (After warming up engine)
MTBL0137
SAT454J
OK or NG OK NG GO TO 6. Check the following items: Throttle position switch Refer to Components Inspection, AT-201. Harness for short or open between ignition switch and throttle position switch (Main harness) Harness for short or open between throttle position switch and TCM (Main harness)
CHECK DTC
AT-200

THROTTLE POSITION SWITCH Closed Throttle Position Switch (Idle position)
=NCAT0072 NCAT0072S01 NCAT0072S0101
Check continuity between terminals 4 and 5. [Refer to Preparation, TCM SELF-DIAGNOSTIC PROCEDURE (No Tools), AT-49.]
Accelerator pedal condition Released Continuity Yes No
SAT851J
Depressed
To adjust closed throttle position switch, refer to EC-445, DTC P0510 CLOSED THROTTLE POSITION SWITCH.
Wide Open Throttle Position Switch

Check continuity between terminals 5 and 6.
Accelerator pedal condition Released Depressed Continuity No Yes
NCAT0072S0102
AX SU BR
SAT852J
AT-201
DTC P1760 OVERRUN CLUTCH SOLENOID VALVE

Description
Description
NCAT0073
The overrun clutch solenoid valve is activated by the TCM in response to signals sent from the inhibitor switch, overdrive control switch, vehicle speed and throttle position sensors. The overrun clutch operation will then be controlled.
SAT283HB

Remarks: Specification data are reference values. Terminal No. Wire color Item Condition When overrun clutch solenoid valve operates. When overrun clutch solenoid valve does not operate.
NCAT0073S01
20
L/B
Overrun clutch solenoid valve
0V

Diagnostic trouble code : O/R CLTCH SOL/CIRC : P1760 Malfunction is detected when ... TCM detects an improper voltage drop when it tries to operate the solenoid valve. Check items (Possible cause)
NCAT0073S02
Harness or connectors (The solenoid circuit is open or shorted.) Overrun clutch solenoid valve

CAUTION: Always drive vehicle at a safe speed. NOTE: If DIAGNOSTIC TROUBLE CODE CONFIRMATION PROCEDURE has been previously conducted, always turn ignition switch OFF and wait at least 5 seconds before conducting the next test. TESTING CONDITION: Always drive vehicle on a level road to improve accuracy of test. After the repair, perform the following procedure to confirm the malfunction is eliminated. With CONSULT-II 1) Turn ignition switch ON and select DATA MONITOR mode for ENGINE with CONSULT-II. 2) Start engine. 3) Accelerate vehicle to a speed of more than 10 km/h (6 MPH) with D position (OD ON). 4) Release accelerator pedal completely with D position (OD OFF).
SAT014K
SEF949Y
AT-202

Description (Contd)
With GST Follow the procedure With CONSULT-II.
AT-203

Wiring Diagram AT OVRCSV
Wiring Diagram AT OVRCSV
NCAT0213
TAT237
AT-204

NCAT0074
GI MA EM LC EC FE
SAT908J
OK or NG OK NG GO TO 2. 1. Remove control valve assembly. Refer to AT-280. 2. Check the following items: Overrun clutch solenoid valve Refer to Component Inspection, AT-207. Harness of terminal cord assembly for short or open
CL MT
AT-205

SAT909J
CHECK DTC
AT-206

OVERRUN CLUTCH SOLENOID VALVE
Resistance Check
Solenoid valve Overrun clutch solenoid valve 3 Terminal No. Ground
NCAT0075S0101
SAT910J
MT
Operation Check
NCAT0075S0102
SAT911J
SC EL IDX
AT-207
DTC BATT/FLUID TEMP SEN (A/T FLUID TEMP SENSOR CIRCUIT AND TCM POWER SOURCE)
Description
Description
NCAT0076
The A/T fluid temperature sensor detects the A/T fluid temperature and sends a signal to the TCM.
SAT283HB
SAT021J

Remarks: Specification data are reference values. Monitor item A/T fluid temperature sensor Condition Cold [20C (68F)] " Hot [80C (176F)] Specification (Approximately) 1.5V " 0.5V 2.5 k " 0.3 k

Remarks: Specification data are reference values. Terminal No. Wire color Item Condition When turning ignition switch to ON. 10 R Power source When turning ignition switch to OFF. 19 R Power source Same as No. 10 When turning ignition switch to OFF. 28 P Power source (Memory back-up) or When turning ignition switch to ON. Ground (A/T fluid temperature sensor) 0V
NCAT0076S02
Battery voltage
Battery voltage
42
When ATF temperature is 20C (68F). When ATF temperature is 80C (176F).
1.5V 0.5V
47
BR
AT-208
Description (Contd)

Diagnostic trouble code : BATT/FLUID TEMP SEN : 8th judgement flicker Malfunction is detected when ... TCM receives an excessively low or high voltage from the sensor. Check items (Possible cause)
NCAT0076S03
GI MA EM LC
Harness or connectors (The sensor circuit is open or shorted.) A/T fluid temperature sensor

After the repair, perform the following procedure to confirm the malfunction is eliminated. With CONSULT-II 1) Start engine. 2) Select DATA MONITOR mode for A/T with CONSULT-II. 3) Drive vehicle under the following conditions: Selector lever in D, vehicle speed higher than 20 km/h (12 MPH). Without CONSULT-II 1) Start engine. 2) Drive vehicle under the following conditions: Selector lever in D, vehicle speed higher than 20 km/h (12 MPH). 3) Perform self-diagnosis. Refer to TCM SELF-DIAGNOSTIC PROCEDURE (No Tools), AT-49.
EC FE CL MT
SAT014K
AX SU BR
SAT971J
ST RS BT HA
SAT335HC
SC EL IDX
AT-209
Wiring Diagram AT BA/FTS
Wiring Diagram AT BA/FTS
NCAT0214
TAT238
AT-210
1 CHECK TCM POWER SOURCE
1. Turn ignition switch to ON position. (Do not start engine.) 2. Check voltage between TCM terminals 10, 19, 28 and ground. Voltage: Battery voltage 3. Turn ignition switch to OFF position. 4. Check voltage between TCM terminal 28 and ground. Voltage: Battery voltage
NCAT0077
SAT461J
MT
OK or NG OK NG GO TO 2. Check the following items: Harness for short or open between ignition switch and TCM (Main harness) Ignition switch and fuse Refer to EL-9, POWER SUPPLY ROUTING.
AT-211
CHECK A/T FLUID TEMPERATURE SENSOR WITH TERMINAL CORD ASSEMBLY
1. Turn ignition switch to OFF position. 2. Disconnect terminal cord assembly connector in engine compartment. 3. Check resistance between terminals 6 and 7 when A/T is cold. Resistance: Cold [20C (68F)] Approximately 2.5 k
SAT912J
4. Reinstall any part removed. OK or NG OK (With CONSULT-II) OK (Without CONSULTII) NG GO TO 3. GO TO 4. 1. Remove oil pan. 2. Check the following items: A/T fluid temperature sensor Refer to Component Inspection, AT-214. Harness of terminal cord assembly for short or open
CHECK INPUT SIGNAL OF A/T FLUID TEMPERATURE SENSOR (WITH CONSULT-II)
With CONSULT-II 1. Start engine. 2. Select TCM INPUT SIGNALS in DATA MONITOR mode for A/T with CONSULT-II. 3. Read out the value of FLUID TEMP SE. Voltage: Cold [20C (68F)] Hot [80C (176F)]: Approximately 1.5V 0.5V
SAT614J
OK or NG OK NG GO TO 5. Check the following item: Harness for short or open between TCM, ECM and terminal cord assembly (Main harness) Ground circuit for ECM Refer to EC-147, TROUBLE DIAGNOSIS FOR POWER SUPPLY.
AT-212
CHECK INPUT SIGNAL OF A/T FLUID TEMPERATURE SENSOR (WITHOUT CONSULT-II)
Without CONSULT-II 1. Start engine. 2. Check voltage between TCM terminal 47 and ground while warming up A/T. Voltage: Cold [20C (68F)] Hot [80C (176F)]: Approximately 1.5V 0.5V
GI MA EM LC EC FE
SAT463J
3. Turn ignition switch to OFF position. 4. Disconnect TCM harness connector. 5. Check resistance between terminal 42 and ground. Continuity should exist.
CL MT
AX SU
SAT464J
OK or NG OK NG GO TO 5. Check the following item: Harness for short or open between TCM, ECM and terminal cord assembly (Main harness) Ground circuit for ECM Refer to EC-147, TROUBLE DIAGNOSIS FOR POWER SUPPLY.
CHECK DTC
AT-213
A/T FLUID TEMPERATURE SENSOR

For removal, refer to AT-280. Check resistance between two terminals while changing temperature as shown at left.
Temperature C (F) 20 (68) 80 (176) Resistance Approximately 2.5 k Approximately 0.3 k
SAT298F
AT-214
DTC VHCL SPEED SENMTR VEHICLE SPEED SENSORMTR

Description
Description
NCAT0079
The vehicle speed sensorMTR is built into the speedometer assembly. The sensor functions as an auxiliary device to the revolution sensor when it is malfunctioning. The TCM will then use a signal sent from the vehicle speed sensorMTR.
GI MA EM
SAT801I
LC
NCAT0079S01
Remarks: Specification data are reference values. Terminal No. Wire color Item Condition Judgement standard
EC FE
40
Y/G
Vehicle speed sensor
When moving vehicle at 2 to 3 km/h (1 to 2 MPH) for 1 m (3 ft) or more.
Voltage varies between less than 1V and more than 4.5V
CL MT

Diagnostic trouble code : VHCL SPEED SENMTR : 2nd judgement flicker Malfunction is detected when ... TCM does not receive the proper voltage signal from the sensor. Check items (Possible cause)
NCAT0079S02
Harness or connectors (The sensor circuit is open or shorted.) Vehicle speed sensor
AT-215

Description (Contd)

CAUTION: Always drive vehicle at a safe speed. If conducting this DTC CONFIRMATION PROCEDURE again, always turn ignition switch OFF and wait at least 5 seconds before continuing. After the repair, perform the following procedure to confirm the malfunction is eliminated. With CONSULT-II 1) Turn ignition switch ON and select DATA MONITOR mode for A/T with CONSULT-II. 2) Start engine and accelerate vehicle from 0 to 25 km/h (0 to 16 MPH). Without CONSULT-II 1) Start engine. 2) Drive vehicle under the following conditions: Selector lever in D and vehicle speed higher than 25 km/h (16 MPH). 3) Perform self-diagnosis. Refer to TCM SELF-DIAGNOSTIC PROCEDURE (No Tools), AT-49.
SAT014K
SAT971J
SAT329HA
AT-216

Wiring Diagram AT VSSMTR
Wiring Diagram AT VSSMTR
NCAT0215
TAT271
AT-217

1 CHECK INPUT SIGNAL
With CONSULT-II 1. Start engine. 2. Select TCM INPUT SIGNALS in DATA MONITOR mode for A/T with CONSULT-II. 3. Read out the value of VHCL/S SEMTR while driving. Check the value changes according to driving speed.
NCAT0080
SAT614J
Without CONSULT-II 1. Start engine. 2. Check voltage between TCM terminal 40 and ground while driving at 2 to 3 km/h (1 to 2 MPH) for 1 m (3 ft) or more. Voltage: Voltage varies between less than 1V and more than 4.5V.
SAT465J
OK or NG OK NG GO TO 2. Check the following items: Vehicle speed sensor and ground circuit for vehicle speed sensor Refer to EL-84, METERS AND GAUGES. Harness for short or open between TCM and vehicle speed sensor (Main harness)
CHECK DTC
AT-218
DTC CONTROL UNIT (RAM), CONTROL UNIT (ROM)

Description
Description
NCAT0218
The TCM consists of a microcomputer and connectors for signal input and output and for power supply. The unit controls the A/T.
GI MA EM
SAT574J
LC
NCAT0218S01
Diagnostic Trouble Code No. : CONTROL UNIT (RAM), CONTROL UNIT (ROM)
Malfunction is detected when .... TCM memory (RAM) or (ROM) is malfunctioning.
Check Item (Possible Cause) TCM
EC FE CL MT

NOTE: If DIAGNOSTIC TROUBLE CODE CONFIRMATION PROCEDURE has been previously conducted, always turn ignition switch OFF and wait at least 5 seconds before conducting the next test. With CONSULT-II 1) Turn ignition switch ON and select DATA MONITOR mode for A/T with CONSULT-II. 2) Start engine. 3) Run engine for at least 2 seconds at idle speed.
SAT014K
SAT971J
1 INSPECTION START (WITH CONSULT-II)
With CONSULT-II 1. Turn ignition switch ON and select SELF DIAGNOSIS mode for A/T with CONSULT-II. 2. Touch ERASE. GO TO 2.
NCAT0219
SC EL IDX
AT-219
DTC CONTROL UNIT (RAM), CONTROL UNIT (ROM)

CHECK DTC
PERFORM DIAGNOSTIC TROUBLE CODE (DTC) CONFIRMATION PROCEDURE. See above. GO TO 3.
CHECK DTC AGAIN
Is the CONTROL UNIT (RAM) or CONTROL UNIT (ROM) displayed again? Yes or No Yes No Replace TCM. INSPECTION END
AT-220
DTC CONTROL UNIT (EEP ROM)

Description
Description
NCAT0221
The TCM consists of a microcomputer and connectors for signal input and output and for power supply. The unit controls the A/T.
GI MA EM
SAT574J
LC
NCAT0221S01
Diagnostic trouble code : CONT UNIT (EEP ROM)
Malfunction is detected when ... TCM memory (EEP ROM) is malfunctioning.
Check item (Possible cause) TCM
EC FE CL MT

NOTE: If DIAGNOSTIC TROUBLE CODE CONFIRMATION PROCEDURE has been previously conducted, always turn ignition switch OFF and wait at least 5 seconds before conducting the next test. With CONSULT-II 1) Turn ignition switch ON and select DATA MONITOR mode for A/T with CONSULT-II. 2) Start engine. 3) Run engine for at least 2 seconds at idle speed.
SAT014K
SAT971J
SC EL IDX
AT-221
DTC CONTROL UNIT (EEP ROM)

1 CHECK DTC
With CONSULT-II 1. Turn ignition switch ON and select SELF DIAGNOSIS mode for A/T with CONSULT-II. 2. Move selector lever to R position. 3. Depress accelerator pedal (Full throttle position). 4. Touch ERASE. 5. Turn ignition switch OFF position for 10 seconds. PERFORM DIAGNOSTIC TROUBLE CODE (DTC) CONFIRMATION PROCEDURE. See previous page. Is the CONT UNIT (EEP ROM) displayed again? Yes No Replace TCM. INSPECTION END
NCAT0222
AT-222
TROUBLE DIAGNOSES FOR SYMPTOMS

Wiring Diagram AT NONDTC
Wiring Diagram AT NONDTC
NCAT0216
TAT272
AT-223

Wiring Diagram AT NONDTC (Contd)
TAT241
AT-224

1. O/D OFF Indicator Lamp Does Not Come On
1. O/D OFF Indicator Lamp Does Not Come On
=NCAT0081
SYMPTOM: O/D OFF indicator lamp does not come on for about 2 seconds when turning ignition switch to ON.
GI MA EM
SAT466J
LC EC FE CL MT
CHECK TCM POWER SOURCE
1. Turn ignition switch to ON position. (Do not start engine.) 2. Check voltage between TCM terminals 10, 19, 28 and ground. Voltage: Battery voltage
SAT467J
3. Turn ignition switch to OFF position. 4. Check voltage between TCM terminal 28 and ground. Voltage: Battery voltage OK or NG OK NG GO TO 2. Check the following items: Harness for short or open between ignition switch and TCM (Main harness) Refer to Wiring Diagram AT MAIN, AT-104. Ignition switch and fuse Refer to EL-9, POWER SUPPLY ROUTING.
AT-225

1. O/D OFF Indicator Lamp Does Not Come On (Contd)
CHECK TCM GROUND CIRCUIT
1. Turn ignition switch to OFF position. 2. Disconnect TCM harness connector. 3. Check continuity between TCM terminals 25, 48 and ground.
SAT468J
Continuity should exist. If OK, check harness for short to ground and short to power. OK or NG OK NG GO TO 3. Repair open circuit or short to ground or short to power in harness or connectors. Refer to Wiring Diagram AT MAIN, AT-104.
CHECK LAMP CIRCUIT
1. Turn ignition switch to OFF position. 2. Check resistance between TCM terminals 13 and 10. Resistance: 50 - 100
SAT469JA
3. Reinstall any part removed. OK or NG OK NG GO TO 4. Check the following items: O/D OFF indicator lamp. Refer to EL-84, METERS AND GAUGES. Harness and fuse for short or open between ignition switch and O/D OFF indicator lamp (Main harness) Refer to EL-9, POWER SUPPLY ROUTING. Harness for short or open between O/D OFF indicator lamp and TCM.
AT-226

1. O/D OFF Indicator Lamp Does Not Come On (Contd)
CHECK SYMPTOM
Check again. OK or NG OK NG INSPECTION END 1. Perform TCM input/output signal inspection. 2. If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
AT-227

2. Engine Cannot Be Started In P and N Position
2. Engine Cannot Be Started In P and N Position
=NCAT0082
SYMPTOM: Engine cannot be started with selector lever in P or N position. Engine can be started with selector lever in D, 2, 1 or R position.
1 CHECK PNP SWITCH CIRCUIT
With CONSULT-II Does TCM INPUT SIGNALS in DATA MONITOR show damage to PNP switch circuit? Without CONSULT-II Does self-diagnosis show damage to PNP switch circuit?
SAT367J
Yes or No Yes No Check PNP switch circuit. Refer to DTC P0705, AT-107. GO TO 2.
CHECK PNP SWITCH INSPECTION
Check for short or open of PNP switch harness connector terminals 1 and 2. Refer to Component Inspection, AT-112.
SAT408J
OK or NG OK NG GO TO 3. Repair or replace PNP switch.
CHECK STARTING SYSTEM
Check starting system. Refer to SC-10, STARTING SYSTEM. OK or NG OK NG INSPECTION END Repair or replace damaged parts.
AT-228

3. In P Position, Vehicle Moves Forward Or Backward When Pushed
3. In P Position, Vehicle Moves Forward Or Backward When Pushed
=NCAT0083
SYMPTOM: Vehicle moves when it is pushed forward or backward with selector lever in P position.
1 CHECK PARKING COMPONENTS
Check parking components. Refer to Parking Pawl Components, AT-286, 291.
GI MA EM LC EC FE
SAT282F
CL MT
OK or NG OK NG INSPECTION END Repair or replace damaged parts.
AT-229

4. In N Position, Vehicle Moves
4. In N Position, Vehicle Moves
=NCAT0084
SYMPTOM: Vehicle moves forward or backward when selecting N position.

With CONSULT-II Does TCM INPUT SIGNALS in DATA MONITOR show damage to PNP switch circuit? Without CONSULT-II Does self-diagnosis show damage to inhibitor switch circuit?
SAT367J
CHECK CONTROL CABLE
Check control cable. Refer to AT-281.
SAT023JB
OK or NG OK NG GO TO 3. Adjust control cable. Refer to AT-281.
AT-230

4. In N Position, Vehicle Moves (Contd)
CHECK A/T FLUID LEVEL
Check A/T fluid level again.
GI MA EM LC
SAT638A
EC FE CL MT
OK or NG OK NG GO TO 4. Refill ATF.
CHECK A/T FLUID CONDITION
1. Remove oil pan. 2. Check A/T fluid condition.
AX SU
SAT171B
BR ST RS BT HA
OK or NG OK NG GO TO 5. 1. Disassemble A/T. 2. Check the following items: Forward clutch assembly Overrun clutch assembly Reverse clutch assembly
CHECK SYMPTOM
SC EL IDX
AT-231

5. Large Shock. N R Position
5. Large Shock. N R Position

1 CHECK SELF-DIAGNOSTIC RESULTS
=NCAT0085
SYMPTOM: There is large shock when changing from N to R position.

Does self-diagnosis show damage to A/T fluid temperature sensor, line pressure solenoid valve or throttle position sensor circuit?
SAT345HA
Yes or No Yes No Check damaged circuit. Refer to DTC P0710, P0745 or P1705, AT-113, 174 or 193. GO TO 2.
CHECK THROTTLE POSITION SENSOR
Check throttle position sensor. Refer to EC-177, DTC P0120 THROTTLE POSITION SENSOR.
SAT413J
OK or NG OK NG GO TO 3. Repair or replace throttle position sensor.
AT-232

5. Large Shock. N R Position (Contd)
CHECK LINE PRESSURE
Check line pressure at idle with selector lever in D position. Refer to Line Pressure Test, AT-66.
GI MA EM LC
SAT494G
OK or NG OK NG GO TO 4. 1. Remove control valve assembly. Refer to AT-280. 2. Check the following items: Valves to control line pressure (Pressure regulator valve, pressure modifier valve, pilot valve and pilot filter) Line pressure solenoid valve
EC FE CL MT
CHECK SYMPTOM
AT-233

6. Vehicle Does Not Creep Backward In R Position
6. Vehicle Does Not Creep Backward In R Position

1 CHECK A/T FLUID LEVEL
=NCAT0086
SYMPTOM: Vehicle does not creep backward when selecting R position.

SAT638A
CHECK STALL TEST
Check stall revolution with selector lever in 1 and R positions.
SAT493G
OK or NG OK OK in 1 position, NG in R position GO TO 3. 1. Remove control valve assembly. Refer to ON-VEHICLE SERVICE, AT-280. 2. Check the following items: Valves to control line pressure (Pressure regulator valve, pressure modifier valve, pilot valve and pilot filter) Line pressure solenoid valve 3. Disassemble A/T. 4. Check the following items: Oil pump assembly Torque converter Reverse clutch assembly High clutch assembly GO TO 6.
NG in both 1 and R positions
AT-234

6. Vehicle Does Not Creep Backward In R Position (Contd)
CHECK LINE PRESSURE
Check line pressure at idle with selector lever in R position. Refer to Line Pressure Test, AT-66.
GI MA EM LC
SAT494G
OK or NG OK NG GO TO 4. 1. Remove control valve assembly. Refer to ON-VEHICLE SERVICE, AT-280. 2. Check the following items: Valves to control line pressure (Pressure regulator valve, pressure modifier valve, pilot valve and pilot filter) Line pressure solenoid valve 3. Disassemble A/T. 4. Check the following item: Oil pump assembly
EC FE CL MT
AX SU BR ST
SAT171B
RS BT HA
CHECK SYMPTOM
SC EL IDX
AT-235

6. Vehicle Does Not Creep Backward In R Position (Contd)
1. Remove control valve assembly. Refer to ON-VEHICLE SERVICE, AT-280. 2. Check the following items: Valves to control line pressure (Pressure regulator valve, pressure modifier valve, pilot valve and pilot filter) Line pressure solenoid valve 3. Disassemble A/T. 4. Check the following items: Oil pump assembly Torque converter Reverse clutch assembly High clutch assembly Low & reverse brake assembly Low one-way clutch OK or NG OK NG GO TO 5. Repair or replace damaged parts.
AT-236

7. Vehicle Does Not Creep Forward In D, 2 Or 1 Position
7. Vehicle Does Not Creep Forward In D, 2 Or 1 Position
=NCAT0087
SYMPTOM: Vehicle does not creep forward when selecting D, 2 or 1 position.

1 CHECK A/T FLUID LEVEL
GI MA EM LC EC FE
SAT638A
CL MT
CHECK STALL TEST
Check stall revolution with selector lever in D position. Refer to Stall Test, AT-62.
AX SU BR ST
SAT493G
RS BT HA SC EL IDX
AT-237

7. Vehicle Does Not Creep Forward In D, 2 Or 1 Position (Contd)
CHECK LINE PRESSURE
Check line pressure at idle with selector lever in D position. Refer to Line Pressure Test , AT-66.
SAT494G
OK or NG OK NG GO TO 4. 1. Remove control valve assembly. Refer to AT-280. 2. Check the following items: Valves to control line pressure (Pressure regulator valve, pressure modifier valve, pilot valve and pilot filter) Line pressure solenoid valve 3. Disassemble A/T. 4. Check the following item: Oil pump assembly
SAT171B
CHECK SYMPTOM
AT-238

7. Vehicle Does Not Creep Forward In D, 2 Or 1 Position (Contd)
1. Remove control valve assembly. Refer to AT-280. 2. Check the following items: Valves to control line pressure (Pressure regulator valve, pressure modifier valve, pilot valve and pilot filter) Line pressure solenoid valve 3. Disassemble A/T. 4. Check the following items: Oil pump assembly Forward clutch assembly Forward one-way clutch Low one-way clutch Low & reverse brake assembly Torque converter OK or NG OK NG GO TO 5. Repair or replace damaged parts.
AT-239

8. Vehicle Cannot Be Started From D1
8. Vehicle Cannot Be Started From D1

1 CHECK SYMPTOM
=NCAT0088
SYMPTOM: Vehicle cannot be started from D1 on Cruise test Part 1.

Is 6. Vehicle Does Not Creep Backward In R Position OK? Yes or No Yes No GO TO 2. Go to 6. Vehicle Does Not Creep Backward In R Position, AT-234.
CHECK SELF-DIAGNOSTIC RESULTS
Does self-diagnosis show damage to vehicle speed sensorA/T (revolution sensor), shift solenoid valve A, B or vehicle speed sensorMTR after cruise test?
SAT934FB
Yes or No Yes No Check damaged circuit. Refer to DTC P0720, P0750, P0755 or VHCL SPEED SENMTR, AT-119, 181, 187 or 215. GO TO 3.
SAT413J
AT-240

8. Vehicle Cannot Be Started From D1 (Contd)
CHECK LINE PRESSURE
Check line pressure at stall point with selector lever in D position. Refer to Line Pressure Test, AT-86.
GI MA EM LC
SAT494G
EC FE CL MT
AX SU
SAT171B
BR ST RS BT HA SC
1. Remove control valve assembly. Refer to AT-280. 2. Check the following items: Shift valve A Shift valve B Shift solenoid valve A Shift solenoid valve B Pilot valve Pilot filter OK or NG OK NG GO TO 7. Repair or replace damaged parts.
EL IDX
AT-241

8. Vehicle Cannot Be Started From D1 (Contd)
CHECK SYMPTOM
1. Remove control valve assembly. Refer to AT-280. 2. Check the following items: Shift valve A Shift valve B Shift solenoid valve A Shift solenoid valve B Pilot valve Pilot filter 3. Disassemble A/T. 4. Check the following items: Forward clutch assembly Forward one-way clutch Low one-way clutch High clutch assembly Torque converter Oil pump assembly OK or NG OK NG GO TO 7. Repair or replace damaged parts.
AT-242

9. A/T Does Not Shift: D1 D2 Or Does Not Kickdown: D4 D2
9. A/T Does Not Shift: D1 D2 Or Does Not Kickdown: D4 D2
=NCAT0089
SYMPTOM: A/T does not shift from D1 to D2 at the specified speed. A/T does not shift from D4 to D2 when depressing accelerator pedal fully at the specified speed.
1 CHECK SYMPTOM
Are 7. Vehicle Does Not Creep Forward In D, 2 Or 1 Position and 8. Vehicle Cannot Be Started From D1 OK? Yes or No Yes No GO TO 2. Go to 7. Vehicle Does Not Creep Forward In D, 2 Or 1 Position and 8. Vehicle Cannot Be Started From D1, AT-237, 240.
CHECK PNP SWITCH CIRCUIT
AX SU
SAT367J
CHECK VEHICLE SPEED SENSORA/T AND CHECK VEHICLE SPEED SENSORMTR CIRCUIT
Check vehicle speed sensorA/T (revolution sensor) and vehicle speed sensorMTR circuit. Refer to DTC P0720 and VHCL SPEED SENMTR, AT-119, AT-215. OK or NG OK NG GO TO 4. Repair or replace vehicle speed sensorA/T (revolution sensor) and vehicle speed sensorMTR circuits.
AT-243

9. A/T Does Not Shift: D1 D2 Or Does Not Kickdown: D4 D2 (Contd)
SAT413J
CHECK A/T FLUID CONIDITION
SAT171B
1. Remove control valve. Refer to AT-280. 2. Check the following items: Shift valve A Shift solenoid valve A Pilot valve Pilot filter OK or NG OK NG GO TO 7. Repair or replace damaged parts.
AT-244

9. A/T Does Not Shift: D1 D2 Or Does Not Kickdown: D4 D2 (Contd)
CHECK SYMPTOM
OK or NG
1. Remove control valve. Refer to AT-280. 2. Check the following items: Shift valve A Shift solenoid valve A Pilot valve Pilot filter 3. Disassemble A/T. 4. Check the following items: Servo piston assembly Brake band Oil pump assembly
MT
OK NG
GO TO 7. Repair or replace damaged parts.
AT-245

10. A/T Does Not Shift: D2 D3

SYMPTOM: A/T does not shift from D2 to D3 at the specified speed.
1 CHECK SYMPTOM
Are 7. Vehicle Does Not Creep Forward In D, 2 Or 1 Position and 8. Vehicle Cannot Be Started From D1 OK? Yes or No Yes No GO TO 2.
=NCAT0090
Go to 7. Vehicle Does Not Creep Forward In D, 2 Or 1 Position and 8. Vehicle Cannot Be Started From D1, AT-237, 240.
CHECK PNP SWITCH CIRCUIT
SAT367J
SAT413J
AT-246

10. A/T Does Not Shift: D2 D3 (Contd)
GI MA EM LC
SAT171B
EC FE CL
1. Remove control valve assembly. Refer to AT-280. 2. Check the following items: Shift valve B Shift solenoid valve B Pilot valve Pilot filter OK or NG OK NG GO TO 6. Repair or replace damaged parts.
MT
AX SU BR
CHECK SYMPTOM
AT-247

1. Remove control valve assembly. Refer to AT-280. 2. Check the following items: Shift valve B Shift solenoid valve B Pilot valve Pilot filter 3. Disassemble A/T. 4. Check the following items: Servo piston assembly High clutch assembly Oil pump assembly OK or NG OK NG GO TO 6. Repair or replace damaged parts.
AT-248

=NCAT0091
SYMPTOM: A/T does not shift from D3 to D4 at the specified speed. A/T must be warm before D3 to D4 shift will occur.
1 CHECK SYMPTOM
Are 7. Vehicle Does Not Creep Forward In D, 2 Or 1 Position and 8. Vehicle Cannot Be Started From D1 OK? Yes or No Yes No GO TO 2. Go to 7. Vehicle Does Not Creep Forward In D, 2 Or 1 Position and 8. Vehicle Cannot Be Started From D1, AT-237, 240.
CHECK SELF-DIAGNOSTIC RESULTS
With CONSULT-II Does self-diagnosis, after cruise test, show damage to any of the following circuits? PNP switch Overdrive control switch A/T fluid temperature sensor Vehicle speed sensorA/T (revolution sensor) Shift solenoid valve A or B Vehicle speed sensorMTR
AX SU
SAT363HC
BR ST RS BT HA SC EL
Yes or No Yes No Check damaged circuit. Refer to DTC P0705, P0710, P0720, P0750, P0755 or VHCL SPEED SENMTR, AT-107, 113, 119, 181, 187 or 215. GO TO 3.
SAT413J
IDX
AT-249

SAT171B
1. Remove control valve assembly. Refer to AT-280. 2. Check the following items: Shift valve B Overrun clutch control valve Shift solenoid valve B Pilot valve Pilot filter OK or NG OK NG GO TO 6. Repair or replace damaged parts.
CHECK SYMPTOM
AT-250

1. Remove control valve assembly. Refer to AT-280. 2. Check the following items: Shift valve B Overrun clutch control valve Shift solenoid valve B Pilot valve Pilot filter 3. Disassemble A/T. 4. Check the following items: Servo piston assembly Brake band Torque converter Oil pump assembly OK or NG OK NG GO TO 6. Repair or replace damaged parts.
AT-251

12. A/T Does Not Perform Lock-up
12. A/T Does Not Perform Lock-up

SYMPTOM: A/T does not perform lock-up at the specified speed.
Does self-diagnosis show damage to torque converter clutch solenoid valve circuit after cruise test?
=NCAT0092
SAT346H
Yes or No Yes No Check torque converter clutch solenoid valve circuit. Refer to DTC P0740, AT-157. GO TO 2.
SAT413J
1. Remove control valve. Refer to AT-280. 2. Check following items: Torque converter clutch control valve Torque converter relief valve Torque converter clutch solenoid valve Pilot valve Pilot filter OK or NG OK NG GO TO 4. Repair or replace damaged parts.
AT-252

12. A/T Does Not Perform Lock-up (Contd)
CHECK SYMPTOM
AT-253

13. A/T Does Not Hold Lock-up Condition
13. A/T Does Not Hold Lock-up Condition

1 CHECK DIAGNOSTIC RESULTS
=NCAT0093
SYMPTOM: A/T does not hold lock-up condition for more than 30 seconds.
Does self-diagnosis show damage to engine speed signal circuit after cruise test?
SAT347H
Yes or No Yes No Check engine speed signal circuit. Refer to DTC P0725, AT-124. GO TO 2.
SAT171B
1. Remove control valve assembly. Refer to AT-280. 2. Check the following items: Torque converter clutch control valve Pilot valve Pilot filter OK or NG OK NG GO TO 4. Repair or replace damaged parts.
AT-254

13. A/T Does Not Hold Lock-up Condition (Contd)
CHECK SYMPTOM
GI MA EM LC EC FE
OK or NG
1. Remove control valve assembly. Refer to AT-280. 2. Check the following items: Torque converter clutch control valve Pilot valve Pilot filter 3. Disassemble A/T. 4. Check torque converter and oil pump assembly.
CL MT
OK NG
GO TO 4. Repair or replace damaged parts.
AT-255

14. Lock-up Is Not Released
14. Lock-up Is Not Released

1 CHECK THROTTLE POSITION SWITCH CIRCUIT
=NCAT0094
SYMPTOM: Lock-up is not released when accelerator pedal is released.

With CONSULT-II Does TCM INPUT SIGNALS in DATA MONITOR show damage to closed throttle position switch circuit? Without CONSULT-II Does self-diagnosis show damage to closed throttle position switch circuit?
SAT367J
Yes or No Yes No Check closed throttle position switch circuit. Refer to DTC P0705, AT-107. GO TO 2.
CHECK SYMPTOM
AT-256

15. Engine Speed Does Not Return To Idle (Light Braking D4 D3)
15. Engine Speed Does Not Return To Idle (Light Braking D4 D3)
=NCAT0095
SYMPTOM: Engine speed does not smoothly return to idle when A/T shifts from D4 to D3. Vehicle does not decelerate by engine brake when turning overdrive control switch OFF. Vehicle does not decelerate by engine brake when shifting A/T from D to 2 position.
Does self-diagnosis show damage to overrun clutch solenoid valve circuit after cruise test?
SAT348H
Yes or NO Yes No Check overrun clutch solenoid valve circuit. Refer to DTC P1760, AT-202. GO TO 2.
SAT413J
AT-257

15. Engine Speed Does Not Return To Idle (Light Braking D4 D3) (Contd)
SAT171B
1. Remove control valve assembly. Refer to AT-280. 2. Check the following items: Overrun clutch control valve Overrun clutch reducing valve Overrun clutch solenoid valve OK or NG OK NG GO TO 5. Repair or replace damaged parts.
CHECK SYMPTOM
1. Remove control valve assembly. Refer to AT-280. 2. Check the following items: Overrun clutch control valve Overrun clutch reducing valve Overrun clutch solenoid valve 3. Disassemble A/T. 4. Check the following items: Overrun clutch assembly Oil pump assembly OK or NG OK NG GO TO 5. Repair or replace damaged parts.
AT-258

16. Vehicle Does Not Start From D1
16. Vehicle Does Not Start From D1

SYMPTOM: Vehicle does not start from D1 on Cruise test Part 2.
Does self-diagnosis show damage to vehicle speed sensorA/T (revolution sensor), shift solenoid valve A, B or vehicle speed sensorMTR after cruise test?
NCAT0096
GI MA EM LC EC FE
SAT934FA
Yes or No Yes No Check damaged circuit. Refer to DTC P0720, P0750, P0755 or VHCL SPEED SENMTR, AT-119, 181, 187 or 215. GO TO 2.
CL MT
CHECK SYMPTOM
Check again. OK or NG OK NG Go to 8. Vehicle Cannot Be Started From D1, AT-240. 1. Perform TCM input/output signal inspection. 2. If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
AT-259

17. A/T Does Not Shift: D4 D3, When Overdrive Control Switch ON OFF
17. A/T Does Not Shift: D4 D3, When Overdrive Control Switch ON OFF
=NCAT0097
SYMPTOM: A/T does not shift from D4 to D3 when changing overdrive control switch to OFF position.
1 CHECK OVERDRIVE CONTROL SWITCH CIRCUIT
With CONSULT-II Does TCM INPUT SIGNALS in DATA MONITOR show damage to overdrive control switch circuit? Without CONSULT-II Does self-diagnosis show damage to overdrive control switch circuit?
SAT344H
Yes or No Yes No Check overdrive control switch circuit. Refer to AT-264. Go to 10. A/T Does Not Shift: D2 , D3, AT-246.
AT-260

18. A/T Does Not Shift: D3 22, When Selector Lever D 2 Position
18. A/T Does Not Shift: D3 22, When Selector Lever D 2 Position
=NCAT0098
SYMPTOM: A/T does not shift from D3 to 22 when changing selector lever from D to 2 position.
SAT367J
MT
Yes or No Yes No Check PNP switch circuit. Refer to DTC P0705, AT-107. Go to 9. A/T Does Not Shift: D1 , D2 or Does Not Kickdown: D4 , D2, AT-243.
AT-261

19. A/T Does Not Shift: 22 11, When Selector Lever 2 1 Position
19. A/T Does Not Shift: 22 11, When Selector Lever 2 1 Position
=NCAT0099
SYMPTOM: A/T does not shift from 22 to 11 when changing selector lever from 2 to 1 position.
SAT367J
CHECK SYMPTOM
Check again.
SAT778B
OK or NG OK NG INSPECTION END 1. Perform TCM input/output signal inspection. 2. If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
AT-262

20. Vehicle Does Not Decelerate By Engine Brake
20. Vehicle Does Not Decelerate By Engine Brake
=NCAT0100
SYMPTOM: Vehicle does not decelerate by engine brake when shifting from 22 (12) to 11.
1 CHECK SYMPTOM
Is 6. Vehicle Does Not Creep Backward In R Position OK? Yes or No Yes No Go to 15. Engine Speed Does Not Return To Idle (Light Braking D4 , D3), AT-257. Go to 6. Vehicle Does Not Creep Backward In R Position, AT-234.
21. TCM Self-diagnosis Does Not Activate (PNP, Overdrive Control and Throttle Position Switches Circuit Checks)
NCAT0101
SYMPTOM: O/D OFF indicator lamp does not come on in TCM self-diagnostic procedure even if the lamp circuit is good.
AX SU
DESCRIPTION
SAT088JA
NCAT0101S01
PNP switch The PNP switch assembly includes a transmission range switch. The transmission range switch detects the selector lever position and sends a signal to the TCM. Overdrive control switch Detects the overdrive control switch position (ON or OFF) and sends a signal to the TCM. Throttle position switch Consists of a wide open throttle position switch and a closed throttle position switch. The wide open throttle position switch sends a signal to the TCM when the throttle valve is open at least 1/2 of the full throttle position. The closed throttle position switch sends a signal to the TCM when the throttle valve is fully closed.
SAT360H
SAT413J
AT-263

21. TCM Self-diagnosis Does Not Activate (PNP, Overdrive Control and Throttle Position Switches Circuit Checks) (Contd)
DIAGNOSTIC PROCEDURE
1 CHECK PNP SWITCH CIRCUIT (With CONSULT-II)
With CONSULT-II 1. Turn ignition switch to ON position. (Do not start engine.) 2. Select TCM INPUT SIGNALS in DATA MONITOR mode for A/T with CONSULT-II. 3. Read out P/N, R, D, 2 and 1 position switches moving selector lever to each position. Check that the signal of the selector lever position is indicated properly.
NCAT0101S02
SAT701J
OK or NG OK NG GO TO 3. Check the following items: PNP switch (Refer to Component Inspection, AT-270.) Harness for short or open between ignition switch and PNP switch (Main harness) Harness for short or open between PNP switch and TCM (Main harness) Diode (P, N positions)
AT-264

CHECK PNP SWITCH CIRCUIT (Without CONSULT-II)
Without CONSULT-II 1. Turn ignition switch to ON position. (Do not start engine.) 2. Check voltage between TCM terminals 26, 27, 34, 35, 36 and ground while moving selector lever through each position. Voltage: B: Battery voltage 0: 0V
GI MA EM LC EC
MTBL0138
FE CL MT
AX SU BR ST
SAT470J
RS BT HA SC EL IDX
OK or NG OK NG GO TO 4. Check the following items: PNP switch (Refer to Component Inspection, AT-270.) Harness for short or open between ignition switch and PNP switch (Main harness) Harness for short or open between PNP switch and TCM (Main harness) Diode (P, N positions)
AT-265

CHECK OVERDRIVE CONTROL SWITCH CIRCUIT (With CONSULT-II)
With CONSULT-II 1. Turn ignition switch to ON position. (Do not start engine.) 2. Select TCM INPUT SIGNALS in DATA MONITOR mode for A/T with CONSULT-II. 3. Read out OVERDRIVE SWITCH. Check the signal of the overdrive control switch is indicated properly. (Overdrive control switch ON displayed on CONSULT-II means overdrive OFF.)
SAT645J
OK or NG OK NG GO TO 5. Check the following items: Overdrive control switch (Refer to Component Inspection, AT-270.) Harness for short or open between TCM and overdrive control switch (Main harness) Harness of ground circuit for overdrive control switch (Main harness) for short or open
AT-266

CHECK OVERDRIVE CONTROL SWITCH CIRCUIT (Without CONSULT-II)
Without CONSULT-II 1. Turn ignition switch to ON position. (Do not start engine.) 2. Check voltage between TCM terminal 22 and ground when overdrive control switch is ON and OFF. Voltage: Switch position ON: Battery voltage Switch position OFF: 1V or less
AX SU
SAT471JA
OK or NG OK NG GO TO 6. Check the following items: Overdrive control switch (Refer to Component Inspection, AT-270.) Harness for short or open between TCM and overdrive control switch (Main harness) Harness of ground circuit for overdrive control switch (Main harness) for short or open
AT-267

CHECK THROTTLE POSITION SWITCH CIRCUIT (With CONSULT-II)
With CONSULT-II 1. Apply vacuum to the throttle opener, then check the following. Refer from step 1 to 5 of Preparation, TCM SELF-DIAGNOSTIC PROCEDURE (No Tools), AT-49. 2. Turn ignition switch to ON position. (Do not start engine.) 3. Select TCM INPUT SIGNALS in DATA MONITOR mode for A/T with CONSULT-II. 4. Read out CLOSED THL/SW and W/O THRL/P-SW depressing and releasing accelerator pedal. Check the signal of throttle position switch is indicated properly.
MTBL0011
SAT702J
OK or NG OK NG GO TO 7. Check the following items: Throttle position switch Refer to Component Inspection, AT-270. Harness for short or open between ignition switch and throttle position switch (Main harness) Harness for short or open between throttle position switch and TCM (Main harness)
AT-268

CHECK THROTTLE POSITION SWITCH CIRCUIT (Without CONSULT-II)
Without CONSULT-II 1. Apply vacuum to the throttle opener, then check the following. Refer from step 1 to 5 of Preparation, TCM SELF-DIAGNOSTIC PROCEDURE (No Tools), AT-49. 2. Turn ignition switch to ON position. (Do not start engine.) 3. Check voltage between TCM terminals 16, 17 and ground while depressing, and releasing accelerator pedal slowly. (After warming up engine)
GI MA EM LC
MTBL0137
EC FE CL MT
AX SU BR
SAT454J
ST RS BT HA SC
OK or NG OK NG GO TO 7. Check the following items: Throttle position switch Refer to Component Inspection, AT-270. Harness for short or open between ignition switch and throttle position switch (Main harness) Harness for short or open between throttle position switch and TCM (Main harness)
CHECK DTC
Perform DIAGNOSTIC PROCEDURE, AT-264. OK or NG OK NG INSPECTION END Perform TCM input/output signal inspection. If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
EL IDX
AT-269

COMPONENT INSPECTION Overdrive Control Switch

Check continuity between two terminals.
Switch position ON OFF Continuity No Yes
NCAT0101S03 NCAT0101S0301
SAT472J
PNP Switch
1.
NCAT0101S0302
Check continuity between terminals 1 and 3 and between terminals 2 and 4, 5, 6, 7, 8, 9 while moving manual shaft through each position.
Lever position P R N D 2 1 37 38 39 36 35 34 12 Terminal No. 12
SAT402J
2. 3. 4. 5. 6.
If NG, check again with manual control cable disconnected from manual shaft of A/T assembly. Refer to step 1. If OK on step 2, adjust manual control cable. Refer to AT-281. If NG on step 2, remove PNP switch from A/T and check continuity of PNP switch terminals. Refer to step 1. If OK on step 4, adjust PNP switch. Refer to AT-281. If NG on step 4, replace PNP switch.
SAT089JA
Throttle Position Switch
NCAT0101S0303
Closed throttle position switch (idle position) Check continuity between terminals 4 and 5. Refer to Preparation, TCM SELF-DIAGNOSTIC PROCEDURE (No Tools), AT-49.
Accelerator pedal condition Released Depressed
SAT851J
Continuity Yes No
To adjust closed throttle position switch, refer to EC-445, DTC
AT-270

P0510 CLOSED THROTTLE POSITION SWITCH.
GI MA EM LC
Wide open throttle position switch Check continuity between terminals 5 and 6.
Accelerator pedal condition Released Depressed Continuity No Yes
EC FE CL
SAT852J
MT
AT-271
A/T SHIFT LOCK SYSTEM

Description
Description
NCAT0102
The mechanical key interlock mechanism also operates as a shift lock: With the key switch turned to ON, the selector lever cannot be shifted from P (parking) to any other position unless the brake pedal is depressed. With the key removed, the selector lever cannot be shifted from P to any other position. The key cannot be removed unless the selector lever is placed in P. The shift lock and key interlock mechanisms are controlled by the ON-OFF operation of the shift lock solenoid and by the operation of the rotator and slider located inside the key cylinder.
Shift Lock System Electrical Parts Location
NCAT0103
SAT862J
AT-272

Wiring Diagram SHIFT
Wiring Diagram SHIFT
NCAT0104
TAT242
AT-273

NCAT0105
SYMPTOM 1: Selector lever cannot be moved from P position with key in ON position and brake pedal applied. Selector lever can be moved from P position with key in ON position and brake pedal released. Selector lever can be moved from P position when key is removed from key cylinder. SYMPTOM 2: Ignition key cannot be removed when selector lever is set to P position. It can be removed when selector lever is set to any position except P.
1 CHECK KEY INTERLOCK CABLE
Check key interlock cable for damage. OK or NG OK NG GO TO 2. Repair key interlock cable. Refer to AT-278.
CHECK SELECTOR LEVER POSITION
Check selector lever position for damage. OK or NG OK NG GO TO 3. Check selector lever. Refer to ON-VEHICLE SERVICE PNP Switch and Control Cable Adjustment, AT-281.
CHECK POWER SOURCE
1. Turn ignition switch to ON position. (Do not start engine.) 2. Check voltage between A/T device harness connector M48 terminal 5 (PU) and ground. Voltage: Battery voltage
SAT663K
AT-274

Check the following items: 1. Harness for short or open between ignition switch and A/T device harness terminal 5 2. Fuse 3. Ignition switch (Refer to EL-9, POWER SUPPLY ROUTING.) OK or NG OK NG GO TO 5. Repair or replace damaged parts.
CHECK INPUT SIGNAL A/T DEVICE
Turn ignition switch to OFF position. Check voltage between A/T device harness connector M48 terminal 7 (R/G) and ground. Voltage: Brake pedal depressed: Battery voltage Brake pedal released: 0V
AX
SAT664K
AT-275

Check the following items: 1. Harness for short or open between battery and stop lamp switch harness connector 1 2. Harness for short or open between stop lamp switch harness connector 2 and A/T device harness connector 7 3. Fuse 4. Stop lamp switch a. Check continuity between stop lamp switch harness connector M32 terminals 1 (R/Y) and 2 (R/G).
SAT661K
Check stop lamp switch after adjusting brake pedal refer to BR-12, BRAKE PEDAL AND BRACKET. OK or NG OK NG GO TO 7. Repair or replace damaged parts.
CHECK GROUND CIRCUIT
1. Turn ignition switch to OFF position. 2. Disconnect A/T device harness connector. 3. Check continuity between A/T device harness terminal 6 and ground. Continuity should exist. If OK, check harness for short to ground and short to power.
SAT857J
OK or NG OK NG GO TO 8. Repair open circuit or short to ground or short to power in harness or connectors.
AT-276

CHECK PARK POSITION SWITCH AND RELAY CIRCUIT (COIL SIDE)
Check continuity between A/T device harness connector M48 terminals 6 (B) and 7 (R/G).
GI MA EM LC
SAT665K
EC FE CL MT
OK or NG OK NG GO TO 9. Replace park position switch or relay.
CHECK SHIFT LOCK SOLENOID AND RELAY CIRCUIT (POINT SIDE)
1. Connect A/T device harness connector. 2. Turn ignition switch to ON position. 3. Check operation sound.
AX
MTBL1313
OK or NG OK NG GO TO 10. Replace shift lock solenoid or relay.
SU BR ST RS BT HA
10
CHECK SHIFT LOCK OPERATION
1. Reconnect shift lock harness connector. 2. Turn ignition switch from OFF to ON position. (Do not start engine.) 3. Recheck shift lock operation. OK or NG OK NG INSPECTION END GO TO 11.
11
CHECK A/T DEVICE INSPECTION
1. Perform A/T device input/output signal inspection test. 2. If NG, recheck harness connector connection. OK or NG OK NG INSPECTION END Repair or replace damaged parts.
SC EL IDX
AT-277
KEY INTERLOCK CABLE

Components
Components
NCAT0107
SAT411J
CAUTION: Install key interlock cable in such a way that it will not be damaged by sharp bends, twists or interference with adjacent parts. After installing key interlock cable to control device, make sure that casing cap and bracket are firmly secured in their positions.
Removal
1.
NCAT0108
Unlock slider by squeezing lock tabs on slider from adjuster holder and remove interlock rod from cable.
SAT853J
AT-278
KEY INTERLOCK CABLE

Removal (Contd)
2.
Remove lock plate from steering lock assembly and remove key interlock cable.
GI MA EM
SAT854J
LC
Installation
1. 2. 3. 4.
NCAT0109
Turn ignition key to lock position. Set A/T selector lever to P position. Set key interlock cable to steering lock assembly and install lock plate. Clamp cable to steering column and fix to control cable with band.
EC FE CL MT
SAT854J
5.
Insert interlock rod into adjuster holder.
AX SU BR
SAT804E
6. 7.
Install casing cap to bracket. Move slider in order to fix adjuster holder to interlock rod.
ST RS BT HA
SAT805E
SC EL IDX
AT-279
ON-VEHICLE SERVICE
Control Valve Assembly and Accumulators
Control Valve Assembly and Accumulators

REMOVAL
1. 2. Drain ATF from transaxle. Remove oil pan and gasket.
NCAT0110
NCAT0110S01
SAT992C
3.
Disconnect A/T solenoid harness connector.
AAT264A
4. 5.
Remove stopper ring from A/T solenoid harness terminal body. Remove A/T solenoid harness by pushing terminal body into transmission case.
AAT265A
6. Remove control valve assembly by removing fixing bolts. Bolt length, number and location:
Bolt symbol Bolt length Number of bolts A 40.0 mm (1.575 in) 5 B 33.0 mm (1.299 in) 6 C 43.5 mm (1.713 in) 2
7.
Be careful not to drop manual valve and servo release accumulator return springs. Disassemble and inspect control valve assembly if necessary. Refer to AT-291.
AAT260A
AT-280
ON-VEHICLE SERVICE
Control Valve Assembly and Accumulators (Contd)
8.
Remove servo release and N-D accumulators by applying compressed air if necessary. Hold each piston with a rag.
GI MA EM
SAT935J
LC
INSTALLATION

NCAT0110S02
Tighten fixing bolts to specification. : 7 - 9 Nm (0.7 - 0.9 kg-m, 61 - 78 in-lb) Set manual shaft in Neutral position, then align manual plate with groove in manual valve. After installing control valve assembly to transmission case, make sure that selector lever can be moved to all positions.
EC FE CL MT
SAT497H
Control Cable Adjustment
NCAT0111
Move selector lever from the P position to the 1 position. You should be able to feel the detents in each position. If the detents cannot be felt or if the pointer indicating the position is improperly aligned, the control cable needs adjustment. 1. Place selector lever in P position. 2. Loosen control cable lock nut and place manual shaft in P position. 3. Pull control cable, by specified force, in the direction of the arrow shown in the illustration. Specified force: 6.9 N (0.7 kg, 1.5 lb) 4. Return control cable in the opposite direction of the arrow for 1.0 mm (0.039 in). 5. Tighten control cable lock nut. 6. Move selector lever from P to 1 position again. Make sure that selector lever moves smoothly. 7. Apply grease to contacting areas of selector lever and control cable. Install any part removed.
AAT980
Park/Neutral Position (PNP) Switch Adjustment SC

NCAT0112
1. 2. 3.
Remove control cable end from manual shaft. Set manual shaft in N position. Loosen PNP switch fixing bolts.
EL IDX
SAT479J
AT-281
ON-VEHICLE SERVICE
Park/Neutral Position (PNP) Switch Adjustment (Contd)
4. a. b. 5. 6. 7. 8. 9.
SAT480J
Use a 4 mm (0.157 in) pin for this adjustment. Insert the pin straight into the manual shaft adjustment hole. Rotate PNP switch until the pin can also be inserted straight into hole in PNP switch. Tighten PNP switch fixing bolts. Remove pin from adjustment hole after adjusting PNP switch. Reinstall any part removed. Adjust control cable. Refer to Control Cable Adjustment. Check continuity of PNP switch. Refer to AT-112.
Differential Side Oil Seal Replacement

1. 2.
NCAT0113
Remove drive shaft assemblies. Refer to AX-10, Drive Shaft. Remove oil seals.
SAT905D
3.
Install oil seals. Apply ATF to oil seal surface before installing.
AAT976
Install oil seals so that dimensions A and B are within specifications.

Unit: mm (in) A 5.5 - 6.5 (0.217 - 0.256) B 0.5 to 0.5 (0.020 to 0.020)
4.
Reinstall any part removed.
SAT489JD
Revolution Sensor Replacement

1. Disconnect revolution sensor harness connector. 2. Remove harness bracket from A/T. 3. Remove revolution sensor from A/T. 4. Reinstall any part removed. Always use new sealing parts.
NCAT0114
SAT303G
AT-282
REMOVAL AND INSTALLATION

Removal
Removal
NCAT0115
CAUTION: Before separating transaxle from engine, remove the crankshaft position sensor (OBD) from transaxle. Be careful not to damage sensor. 1. Remove battery and bracket. 2. Remove air duct between throttle body and air cleaner. 3. Disconnect A/T solenoid harness connector, PNP switch harness connector and revolution sensor harness connector. 4. Remove crankshaft position sensor (OBD) from transaxle.
SAT501HA
MT
Drain ATF from transaxle. Disconnect control cable from transaxle. Disconnect oil cooler hoses. Remove drive shafts. Refer to AX-10, Drive Shaft. Remove the intake manifold support bracket. Refer to EM-10, OUTER COMPONENT PARTS. 10. Remove starter motor from transaxle. Tighten bolts to specified torque. : 41 - 52 Nm (4.2 - 5.3 kg-m, 30 - 38 ft-lb) 11. Remove upper bolts fixing transaxle to engine. 12. Support transaxle with a jack. 5. 6. 7. 8. 9.
SAT304G
13. Remove center member. Tighten center member fixing bolts to specified torque, Refer to EM-52, REMOVAL AND INSTALLATION.
SC EL IDX
AAT469
AT-283

Removal (Contd)
14. Remove rear plate cover. 15. Remove torque converter bolts. Rotate crankshaft to gain access to securing bolts. 16. Remove rear transaxle to engine bracket. Refer to EM-52, REMOVAL AND INSTALLATION. 17. Support engine with a jack. 18. Remove rear transaxle mount. Refer to EM-52, REMOVAL AND INSTALLATION. 19. Remove lower bolts fixing transaxle to engine. 20. Lower transaxle while supporting it with a jack.
AAT259A
Installation
NCAT0116
1. Check drive plate runout. CAUTION: Do not allow any magnetic materials to contact the ring gear teeth. Maximum allowable runout: Refer to EM-64, FLYWHEEL/DRIVE PLATE RUNOUT. If this runout is out of allowance, replace drive plate with ring gear.
SAT977H
2.
When connecting torque converter to transaxle, measure distance A to be certain that they are correctly assembled. Distance A: 15.9 mm (0.626 in) or more
SAT573D
3.
Install torque converter to drive plate. With converter installed, rotate crankshaft several turns to check that transaxle rotates freely without binding.
AAT266A
4.
Tighten belts fixing transaxle.

Bolt No. 1 2 3 4 5 Tightening torque Nm (kg-m, ft-lb) 70 - 79 (7.1 - 8.1, 51 - 59) 70 - 79 (7.1 - 8.1, 51 - 59) 70 - 79 (7.1 - 8.1, 51 - 59) 16 - 21 (1.6 - 2.1, 12 - 15) 16 - 21 (1.6 - 2.1, 12 - 15) Bolt length mm (in) 55 (2.17) 50 (1.97) 65 (2.56) 35 (1.38) 47 (1.85)
SAT558DB
AT-284

Installation (Contd)
5. 6. 7. 8. 9.
Reinstall any part removed. Adjust control cable. Refer to AT-281. Check continuity of PNP switch. Refer to AT-112. Refill transaxle with ATF and check fluid level. Move selector lever through all positions to be sure that transaxle operates correctly. With parking brake applied, idle engine. Move selector lever through N to D, to 2, to 1 and R positions. A slight shock should be felt through the hand gripping the selector each time the transaxle is shifted. 10. Perform road test. Refer to AT-67.
SAT638A
AT-285
OVERHAUL
Components
Components
NCAT0119
SAT865J
AT-286
OVERHAUL
Components (Contd)
SAT936J
AT-287
OVERHAUL
Components (Contd)
SAT287K
AT-288
OVERHAUL
Oil Channel
Oil Channel
NCAT0118
SAT867J
AT-289
OVERHAUL
Locations of Adjusting Shims, Needle Bearings, Thrust Washers and Snap Rings
Locations of Adjusting Shims, Needle Bearings, Thrust Washers and Snap Rings
NCAT0117
SAT325GC
AT-290
NCAT0120
DISASSEMBLY
1. Drain ATF through drain plug.
GI MA EM
SAT007D
LC
2. Remove torque converter.
EC FE CL
SAT008D
MT
3. a. b. c. Check torque converter one-way clutch using check tool as shown at left. Insert check tool into the groove of bearing support built into one-way clutch outer race. While fixing bearing support with check tool, rotate one-way clutch spline using flat-bladed screwdriver. Check inner race rotates clockwise only. If not, replace torque converter assembly.
SAT009D
4.
Remove oil charging pipe and oil cooler tube.
SC EL IDX
SAT586H
AT-291
DISASSEMBLY
5. 6. Set manual shaft to P position. Remove PNP switch.
SAT023JB
7. 8.
SAT128E
9.
Remove oil pan and oil pan gasket. Do not reuse oil pan bolts. Check foreign materials in oil pan to help determine cause of malfunction. If the fluid is very dark, smells burned, or contains foreign particles, the frictional material (clutches, band) may need replacement. A tacky film that will not wipe clean indicates varnish build up. Varnish can cause valves, servo, and clutches to stick and may inhibit pump pressure. If frictional material is detected, replace radiator after repair of A/T. Refer to LC-14, section Radiator. Remove control valve assembly according to the following procedures.
a.
Remove control valve assembly mounting bolts A, B and C.
AAT260A
AT-292
DISASSEMBLY
b. c. Remove stopper ring from terminal body. Push terminal body into transmission case and draw out solenoid harness.
GI MA EM
AAT262A
LC
10. Remove manual valve from control valve assembly as a precaution.
EC FE CL
SAT017D
MT
11. Remove return spring from servo release accumulator piston.
AX SU BR
SAT877J
12. Remove servo release accumulator piston with compressed air. 13. Remove O-rings from servo release accumulator piston.
ST RS BT HA
SAT019DA
14. Remove N-D accumulator piston and return spring with compressed air. 15. Remove O-rings from N-D accumulator piston.
SC EL IDX
SAT020D
AT-293
DISASSEMBLY
16. Check accumulator pistons and contact surface of transmission case for damage. 17. Check accumulator return springs for damage and free length. Return springs: Refer to SDS, AT-399.
SAT023DA
18. Remove lip seals from band servo oil port.
SAT129E
19. Remove converter housing according to the following procedures. a. Remove converter housing mounting bolts A and B.
SAT027D
b.
Remove converter housing.
SAT028D
c.
Remove O-ring from differential oil port.
SAT131E
AT-294
DISASSEMBLY
20. Remove final drive assembly from transmission case.
GI MA EM
SAT030D
LC
21. Remove differential side bearing outer race from transmission case.
EC FE CL
AAT477
MT
22. Remove differential side bearing adjusting shim from transmission case.
AX SU BR
SAT132E
23. Remove differential side bearing outer race from converter housing.
ST RS BT HA
AAT478
24. Remove oil seal from converter housing using a screwdriver. Be careful not to damage case.
SC EL IDX
SAT133E
AT-295
DISASSEMBLY
25. Remove side oil seal from transmission case using a screwdriver.
SAT072D
26. Remove oil tube from converter housing.
SAT134EA
27. Remove oil pump according to the following procedures. a. Remove O-ring from input shaft.
SAT127E
b.
Remove oil pump assembly from transmission case.
SAT035D
c.
Remove thrust washer and bearing race from oil pump assembly.
SAT036D
AT-296
DISASSEMBLY
28. Remove brake band according to the following procedures. a. Loosen lock nut, then back off anchor end pin. Do not reuse anchor end pin.
GI MA EM
SAT037DA
LC
b. Remove brake band from transmission case.
EC FE CL
SAT038D
MT
To prevent brake linings from cracking or peeling, do not stretch the flexible band unnecessarily. When removing the brake band, always secure it with a clip as shown in the figure at left. Leave the clip in position after removing the brake band.
AX SU BR
SAT039D
c.
Check brake band facing for damage, cracks, wear or burns.
ST RS BT HA
SAT040D
29. Remove input shaft assembly (high clutch) and reverse clutch according to the following procedures. a. Remove input shaft assembly (high clutch) with reverse clutch.
SC EL IDX
SAT041D
AT-297
DISASSEMBLY
b. Remove input shaft assembly (high clutch) from reverse clutch.
SAT042D
c. d.
Remove needle bearing from high clutch drum. Check input shaft assembly and needle bearing for damage or wear.
SAT043D
30. Remove high clutch hub and needle bearing from transmission case. 31. Check high clutch hub and needle bearing for damage or wear.
SAT044D
32. Remove front sun gear and needle bearings from transmission case. 33. Check front sun gear and needle bearings for damage or wear.
SAT579D
34. Remove front planetary carrier assembly and low one-way clutch according to the following procedures. a. Remove snap ring using a screwdriver.
SAT046D
AT-298
DISASSEMBLY
b. Remove front planetary carrier with low one-way clutch.
GI MA EM
SAT047D
LC
c. d. Check that low one-way clutch rotates in the direction of the arrow and locks in the opposite direction. Remove low one-way clutch from front planetary carrier by rotating it in the direction of unlock.
EC FE CL
SAT048D
MT
e. Remove needle bearing from front planetary carrier.
AX SU BR
SAT049D
f. g.
Check front planetary carrier, low one-way clutch and needle bearing for damage or wear. Check clearance between pinion washer and planetary carrier using feeler gauge. Standard clearance: 0.15 - 0.70 mm (0.0059 - 0.0276 in) Allowable limit: 0.80 mm (0.0315 in) Replace front planetary carrier if the clearance exceeds allowable limit.
SAT050D
35. Remove rear planetary carrier assembly and rear sun gear according to the following procedures. a. Remove rear planetary carrier assembly from transmission case.
SAT051D
AT-299
DISASSEMBLY
b. Remove rear sun gear from rear planetary carrier.
SAT052D
c.
Remove needle bearings from rear planetary carrier assembly.
SAT053D
d. e.
Check rear planetary carrier, rear sun gear and needle bearings for damage or wear. Check clearance between pinion washer and rear planetary carrier using feeler gauge. Standard clearance: 0.15 - 0.70 mm (0.0059 - 0.0276 in) Allowable limit: 0.80 mm (0.0315 in) Replace rear planetary carrier if the clearance exceeds allowable limit.
SAT054D
36. Remove rear internal gear from transmission case.
SAT055D
37. Remove needle bearing from rear internal gear. Check needle bearing for damage or wear.
SAT056D
AT-300
DISASSEMBLY
38. Remove forward clutch assembly from transmission case.
GI MA EM
SAT272E
LC
39. Remove thrust washer from transmission case.
EC FE CL
AAT215A
MT
40. Remove output shaft assembly according to the following procedures. a. Remove side cover bolts.
AX SU BR
SAT059D
b.
Remove side cover by lightly tapping it with a soft hammer. Be careful not to drop output shaft assembly. It might come out when removing side cover.
ST RS BT HA
SAT434D
c.
Remove adjusting shim.
SC EL IDX
SAT440D
AT-301
DISASSEMBLY
d. Remove output shaft assembly.
SAT439D
If output shaft assembly came off with side cover, tap cover with a soft hammer to separate.
SAT435D
e.
Remove needle bearing.
SAT453D
41. Disassemble reduction pinion gear according to the following procedures. a. Set manual shaft to position P to fix idler gear. b. Unlock idler gear lock nut using a pin punch.
SAT060D
c.
Remove idler gear lock nut. Do not reuse idler gear lock nut.
SAT061D
AT-302
DISASSEMBLY
d. Remove idler gear with puller.
GI MA EM
AAT480
LC
e. f. Remove reduction pinion gear. Remove adjusting shim from reduction pinion gear.
EC FE CL
SAT310G
MT
42. Remove return spring from parking shaft using a screwdriver.
AX SU BR
SAT064D
43. Draw out parking shaft and remove parking pole from transmission case. 44. Check parking pole and shaft for damage or wear.
ST RS BT HA
SAT065D
45. Remove parking actuator support from transmission case. Check parking actuator support for damage or wear.
SC EL IDX
SAT066D
AT-303
DISASSEMBLY
46. Remove revolution sensor from transmission case.
SAT311G
AT-304
REPAIR FOR COMPONENT PARTS

Manual Shaft
Manual Shaft
COMPONENTS
NCAT0121
SAT481J
MT
REMOVAL
1. Remove detent spring from transmission case.
NCAT0122
AX SU BR
SAT313G
2.
Drive out manual plate retaining pin.
ST RS BT HA
AAT486
3. 4. 5.
Drive and pull out parking rod plate retaining pin. Remove parking rod plate from manual shaft. Draw out parking rod from transmission case.
SC EL IDX
AAT534
AT-305

Manual Shaft (Contd)
6. 7.
Pull out manual shaft retaining pin. Remove manual shaft and manual plate from transmission case.
SAT049F
8.
Remove manual shaft oil seal.
SAT080D
INSPECTION
NCAT0123
Check component parts for wear or damage. Replace if necessary.
INSTALLATION
1. Install manual shaft oil seal. Apply ATF to outer surface of oil seal.
NCAT0124
SAT081D
2.
Install manual shaft and manual plate.
SAT610H
AT-306

Manual Shaft (Contd)
3. 4.
Align groove of manual shaft and hole of transmission case. Install manual shaft retaining pin.
GI MA EM
AAT487
LC
5. 6. Install parking rod to parking rod plate. Set parking rod assembly onto manual shaft.
EC FE CL
SAT078D
MT
7. Drive in manual plate retaining pin and parking rod plate retaining pin.
AX SU BR
AAT485
8.
Install detent spring.
ST RS BT HA
SAT313G
SC EL IDX
AT-307

Oil Pump
Oil Pump
COMPONENTS
NCAT0125
SAT931J
DISASSEMBLY
1. Remove seal rings.
NCAT0126
SAT699H
2.
Loosen bolts in numerical order and remove oil pump cover.
SAT091D
3.
Remove inner and outer gear from oil pump housing.
SAT092D
AT-308

Oil Pump (Contd)
4.
Remove O-ring from oil pump housing.
GI MA EM
SAT093D
LC
5. Remove oil pump housing oil seal.
EC FE CL
SAT094D
MT
INSPECTION NCAT0127 Oil Pump Housing, Oil Pump Cover, Inner Gear and Outer Gear NCAT0127S01
Check for wear or damage.
AX SU BR
Side Clearances
NCAT0127S02
Measure side clearance of inner and outer gears in at least four places around each outside edge. Maximum measured values should be within specified range. Standard clearance: 0.02 - 0.04 mm (0.0008 - 0.0016 in) If clearance is less than standard, select inner and outer gear as a set so that clearance is within specifications. Inner and outer gear: Refer to SDS, AT-392. If clearance is more than standard, replace whole oil pump assembly except oil pump cover.
SAT095D
AT-309

Oil Pump (Contd)
Measure clearance between outer gear and oil pump housing. Standard clearance: 0.08 - 0.15 mm (0.0031 - 0.0059 in) Allowable limit: 0.15 mm (0.0059 in) If not within allowable limit, replace whole oil pump assembly except oil pump cover.
SAT096D
Side Ring Clearance

NCAT0127S03
SAT097D
Install new seal rings onto oil pump cover. Measure clearance between seal ring and ring groove. Standard clearance: 0.1 - 0.25 mm (0.0039 - 0.0098 in) Allowable limit: 0.25 mm (0.0098 in) If not within allowable limit, replace oil pump cover assembly.
ASSEMBLY
1. Install oil seal on oil pump housing.
NCAT0128
SAT922D
2.
Install O-ring on oil pump housing. Apply ATF to O-ring.
SAT093D
3.
Install inner and outer gears on oil pump housing. Take care with the direction of the inner gear.
SAT092D
AT-310

Oil Pump (Contd)
4. a.
b.
Install oil pump cover on oil pump housing. Wrap masking tape around splines of oil pump cover assembly to protect seal. Position oil pump cover assembly on oil pump housing assembly, then remove masking tape. Tighten bolts in numerical order.
GI MA EM
SAT101D
LC
5. Install new seal rings carefully after packing ring groove with petroleum jelly. Do not spread gap of seal ring excessively while installing. It may deform the ring.
EC FE CL
SAT699H
MT
AT-311

Control Valve Assembly
Control Valve Assembly

COMPONENTS
=NCAT0129
SAT868J
1. 2. 3. 4. 5. 6. 7. 8.
Solenoid valve assembly O-ring Clip Terminal body Control valve lower body Oil strainer Support plate Lower inter separating gasket
9. 10. 11. 12. 13. 14. 15. 16.
Separating plate Lower separating gasket Steel ball Control valve inter body Pilot filter Upper inter separating gasket Separating plate Upper separating gasket
17. 18. 19. 20. 21. 22. 23.
Steel ball Control valve upper body Check ball Oil cooler relief valve spring O-ring T/C pressure holding spring Check ball
AT-312

Control Valve Assembly (Contd)
DISASSEMBLY
Bolt length, number and location:
Bolt symbol Bolt length Number of bolts F: Reamer bolt with nut A 13.5 mm (0.531 in) 6 B 58.0 mm (2.283 in) 3 C 40.0 mm (1.575 in) 6 D 66.0 mm (2.598 in) 11 E 33.0 mm (1.299 in) 2 F 78.0 mm (3.071 in) 2 G
=NCAT0130
Disassemble upper, inter and lower bodies.
GI
18.0 mm (0.709 in) 1
MA EM LC EC FE CL MT
AX
SAT869J
SU BR
1. Remove bolts A, D and F, and remove oil strainer from control valve assembly.
ST RS BT HA
SAT083F
2.
Remove solenoid valve assembly and line pressure solenoid valve from control valve assembly. Be careful not to lose the line pressure solenoid valve spring.
SC EL IDX
SAT316GA
AT-313

3.
Remove O-rings from solenoid valves and terminal body.
SAT317G
4.
Place upper body facedown, and remove bolts B, C and F.
SAT064F
5.
Remove lower body from inter body.
SAT432D
6.
Turn over lower body, and accumulator support plates.
SAT109D
7. 8.
Remove bolts E, separating plate and separating gaskets from lower body. Remove check balls, oil cooler relief valve springs and T/C pressure holding spring from lower body. Be careful not to lose steel balls and relief valve springs.
SAT873J
AT-314

9. Remove inter body from upper body. 10. Remove pilot filter, separating plate and gaskets from upper body.
GI MA EM
SAT065F
LC
11. Check to see that steel balls are properly positioned in inter body and then remove them. Be careful not to lose steel balls.
EC FE CL
SAT870J
MT
12. Check to see that steel balls are properly positioned in upper body and then remove them. Be careful not to lose steel balls.
AX SU BR
SAT871J
INSPECTION Lower and Upper Bodies
ST RS BT HA
Check to see that retainer plates are properly positioned in lower body.
SAT872J
Check to see that retainer plates are properly positioned in upper body.
SC EL IDX
SAT321G
AT-315

Oil Strainer
Check wire netting of oil strainer for damage.
NCAT0131S02
SAT115D
Shift Solenoid Valves A and B, Line Pressure Solenoid valve, Torque Converter Clutch Solenoid Valve and Overrun Clutch Solenoid Valve NCAT0131S03
Refer to Resistance Check, AT-156, 162 and 207.
SAT283HB
Oil Cooler Relief Valve Spring

Check springs for damage or deformation. Measure free length and outer diameter. Inspection standard:
Part No. 31872 31X00 17.0 (0.669) D
NCAT0131S04
Unit: mm (in)
8.0 (0.315)
SAT138D
ASSEMBLY
1. a.
NCAT0132
Install upper, inter and lower body. Place oil circuit of upper body face up. Install steel balls in their proper positions.
SAT871J
b.
Install upper separating gasket, upper inter separating gasket and upper separating plate in order shown in illustration. Always use new gaskets.
SAT072F
AT-316

c.
Install reamer bolts F from bottom of upper body. Using reamer bolts as guides, install separating plate and gaskets as a seat.
GI MA EM
SAT073F
LC
d. Install pilot filter.
EC FE CL
SAT074F
MT
e. Place inter body as shown in the illustration. Install steel balls in their proper positions.
AX SU BR
SAT870J
f.
Install inter body on upper body using reamer bolts F as guides. Be careful not to dislocate or drop steel balls.
ST RS BT HA
SAT076F
g.
Install check balls, oil cooler relief valve springs and T/C pressure holding spring in their proper positions in lower body.
SC EL IDX
SAT873J
AT-317

h.
Install lower separating gasket, inner separating gasket and lower separating plate in order shown in the illustration.
SAT077F
i. j.
Install bolts E from bottom of lower body. Using bolt E as guides, install separating plate and gaskets as a set. Install support plates on lower body.
SAT078F
k.
Install lower body on inter body using reamer bolts F as guides and tighten reamer bolts F slightly.
AAT536
2.
Install O-rings to solenoid valves and terminal body. Apply ATF to O-rings.
SAT317G
3. Bolt length, number and location:

Bolt symbol Bolt length Number of bolts F: Reamer bolt with nut A 13.5 mm (0.531 in) 6
Install and tighten bolts.

B C 44.0 mm (1.732 in) 6 D 66.0 mm (2.598 in) 11 E 33.0 mm (1.299 in) 2 F 78.0 mm (3.071 in) 2 G 18.0 mm (0.709 in) 1
58.0 mm (2.283 in) 3
AT-318

GI MA EM LC EC FE
SAT869J
CL MT
a.
Install and tighten bolts B to specified torque. : 7 - 9 Nm (0.7 - 0.9 kg-m, 61 - 78 in-lb)
AX SU BR
SAT081F
b.
Install solenoid valve assembly and line pressure solenoid valve to lower body.
ST RS BT HA
SAT316GA
c. d.
Remove reamer bolts F and set oil strainer on control valve assembly. Reinstall reamer bolts F from lower body side.
SC EL IDX
SAT323G
AT-319

e.
Tighten bolts A, C, D and F to specified torque. : 7 - 9 Nm (0.7 - 0.9 kg-m, 61 - 78 in-lb)
SAT083F
f.
Tighten bolts E to specified torque. : 3.4 - 4.4 Nm (0.35 - 0.45 kg-m, 30.4 - 39.1 in-lb)
SAT084FA
AT-320

Control Valve Upper Body
Control Valve Upper Body

COMPONENTS
Numbers preceding valve springs correspond with those shown in SDS table on page AT-390.
=NCAT0133
AX SU BR ST RS
SAT863J
BT HA SC EL IDX
1. 2. 3. 4. 5. 6. 7. 8. 9.
Control valve upper body Return spring Overrun clutch reducing valve Plug Retainer plate Torque converter relief valve Return spring Retainer plate Torque converter clutch control valve 10. Return spring 11. Plug 12. Sleeve
13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24.
Retainer plate 1-2 accumulator valve Return spring Plug Retainer plate Cooler check valve Return spring Plug Retainer plate Retainer plate Return spring Pilot valve
25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36.
Retainer plate Plug 1-2 accumulator piston Return spring 1-2 accumulator retainer plate Retainer plate Plug 1st reducing valve Return spring Retainer plate Return spring 3-2 timing valve
AT-321

Control Valve Upper Body (Contd)
DISASSEMBLY
1. Remove valves at retainer plates. Do not use a magnetic hand.
NCAT0134
SAT321G
a.
Use a screwdriver to remove retainer plates.
SAT135D
b.
Remove retainer plates while holding spring, plugs or sleeves. Remove plugs slowly to prevent internal parts from jumping out.
SAT136D
c.
Place mating surface of valve body face down, and remove internal parts. If a valve is hard to remove, place valve body face down and lightly tap it with a soft hammer. Be careful not to drop or damage valves and sleeves.
SAT137D
INSPECTION Valve Spring

SAT138D
Measure free length and outer diameter of each valve spring. Also check for damage or deformation. Inspection standard: Refer to SDS, AT-390. Replace valve springs if deformed or fatigued.
NCAT0135S02
Control Valves
Check sliding surfaces of valves, sleeves and plugs.
AT-322

ASSEMBLY
NCAT0136
Lay control valve body down when installing valves. Do not stand the control valve body upright.
GI MA EM
SAT139D
LC
1. Lubricate the control valve body and all valves with ATF. Install control valves by sliding them carefully into their bores. Be careful not to scratch or damage valve body.
EC FE CL
SAT140DA
MT
Wrap a small screwdriver with vinyl tape and use it to insert the valves into their proper positions.
AX SU BR
SAT141D
1-2 Accumulator Valve

NCAT0136S01
Install 1-2 accumulator valve. Align 1-2 accumulator retainer plate from opposite side of control valve body. Install return spring, 1-2 accumulator piston and plug.
ST RS BT HA
SAT142D
1.
Install retainer plates. Install retainer plate while pushing plug or return spring.
SC EL IDX
SAT143D
AT-323

Retainer Plate (for control valve upper body)

Refer to AT-321.
NCAT0136S02
Unit: mm (in) Name of valve and piston Pilot valve 1-2 accumulator valve 1-2 accumulator piston 1st reducing valve
SAT086F
No. 22 17
Length A
Length B 21.5 (0.846) 38.5 (1.516)
25 30 5 8 13 34 21 6.0 (0.236) 21.5 (0.846) 24.0 (0.945) 21.5 (0.846) 28.0 (1.102) 21.5 (0.846) 24.0 (0.945)
Overrun clutch reducing valve Torque converter relief valve Torque converter clutch control valve 3-2 timing valve Cooler check valve
Install proper retainer plates.
AT-324

Control Valve Lower Body
Control Valve Lower Body

COMPONENTS
Numbers preceding valve springs correspond with those shown in SDS table on page AT-390.
=NCAT0137
AX SU BR ST RS
SAT864J
BT HA SC EL IDX
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.
Control valve lower body Return spring Shift valve B Plug Retainer plate Pressure modifier valve Return spring Parallel pin Sleeve Piston Return spring Retainer plate
13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24.
Manual valve Retainer plate Sleeve Plug Spring seat Return spring Pressure regulator valve Retainer plate Plug Overrun clutch control valve Return spring Retainer plate
25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35.
Plug Accumulator control valve Return spring Retainer plate Return spring Shift valve A Retainer plate Plug Plug Return spring Shuttle control valve
AT-325

Control Valve Lower Body (Contd)
DISASSEMBLY
Remove valves at retainer plate. For removal procedures, refer to AT-313.
NCAT0138
SAT872J
INSPECTION Valve Springs

SAT138D
Check each valve spring for damage or deformation. Also measure free length and outer diameter. Inspection standard: Refer to SDS, AT-390. Replace valve springs if deformed or fatigued.
NCAT0139S02
Control Valves
Check sliding surfaces of control valves, sleeves and plugs for damage.
NCAT0140
ASSEMBLY
Install control valves. For installation procedures, refer to AT-390.
SAT872J
Retainer Plate (for control valve lower body)

Refer to AT-325.
NCAT0140S01
Unit: mm (in) Name of control valve Pressure regulator valve Accumulator control valve Shift valve A Overrun clutch control valve
SAT089F
No. 14 24 28 20 12 31 5
Length A Length B
Type
6.0 (0.236)
28.0 (1.102)
Pressure modifier valve Shuttle control valve Shift valve B
II
Install proper retainer plates.
AT-326

Reverse Clutch
Reverse Clutch
COMPONENTS
=NCAT0141
SAT485JA
MT
DISASSEMBLY
1. a. b. c.
SAT155D
NCAT0142
Check operation of reverse clutch. Install seal ring onto drum support of oil pump cover and install reverse clutch assembly. Apply compressed air to oil hole. Check to see that retaining plate moves to snap ring. If retaining plate does not contact snap ring: D-ring might be damaged. Oil seal might be damaged. Fluid might be leaking past piston check ball. Remove snap ring. Remove drive plates, driven plates, retaining plate, and dish plates.
2. 3.
SAT156D
4. 5.
Set Tool on spring retainer and remove snap ring from reverse clutch drum while compressing return springs. Set Tool directly above springs. Do not expand snap ring excessively. Remove spring retainer and return springs.
SC EL IDX
AAT489
AT-327

Reverse Clutch (Contd)
Do not remove return springs from spring retainer.
SAT301E
6.
Remove piston from reverse clutch drum by turning it.
SAT159D
7.
Remove D-ring and oil seal from piston.
SAT138E
INSPECTION NCAT0143 Reverse Clutch Snap Ring, Spring Retainer and Return Springs NCAT0143S01
Check for deformation, fatigue or damage. Replace if necessary. When replacing spring retainer and return springs, replace them as a set.
Reverse Clutch Drive Plates

Check facing for burns, cracks or damage. Measure thickness of facing. Thickness of drive plate: Standard value: 2.0 mm (0.079 in) Wear limit: 1.8 mm (0.071 in) If not within wear limit, replace.
NCAT0143S02
SAT162D
AT-328

Reverse Clutch Dish Plates

Check for deformation or damage. Measure thickness of dish plate. Thickness of dish plate t: 2.8 mm (0.110 in) If deformed or fatigued, replace.
NCAT0143S03
GI MA EM
SAT163D
LC
Reverse Clutch Piston

NCAT0143S04
Make sure check balls are not fixed. Apply compressed air to check ball oil hole opposite the return spring. Make sure that there is no air leakage. Apply compressed air to oil hole on return spring side to make sure air leaks past ball.
EC FE CL
SAT164D
MT
ASSEMBLY
1. Install D-ring and oil seal on piston. Take care with the direction of the oil seal. Apply ATF to both parts.
NCAT0144
AX SU BR
SAT160DA
2.
Install piston assembly by turning it slowly. Apply ATF to inner surface of drum.
ST RS BT HA
SAT159D
3.
Install return springs and spring retainer on piston.
SC EL IDX
SAT168D
AT-329

4.
Set Tool on spring retainer and install snap ring while compressing return springs. Set Tool directly above return springs.
AAT489
5.
Install drive plates, driven plates, retaining plate and dish plates. Do not align the projections of any two dish plates. Take care with the order and direction of plates.
SAT170D
6.
Install snap ring.
SAT156D
7.
Measure clearance between retaining plate and snap ring. If not within allowable limit, select proper retaining plate. Specified clearance: Standard: 0.5 - 0.8 mm (0.020 - 0.031 in) Allowable limit: 1.2 mm (0.047 in) Retaining plate: Refer to SDS, AT-390.
SAT174D
8.
Check operation of reverse clutch. Refer to Reverse Clutch, AT-327.
SAT173D
AT-330

High Clutch
High Clutch
COMPONENTS
=NCAT0145
AX SU
SAT874J
DISASSEMBLY
1. a. b. c.
SAT176D
NCAT0146
Check operation of high clutch. Apply compressed air to oil hole of input shaft. Stop up a hole on opposite side of input shaft. Check to see that retaining plate moves to snap ring. If retaining plate does not contact snap ring: D-ring might be damaged. Oil seal might be damaged. Fluid might be leaking past piston check ball. Remove seal rings from input shaft.
2.
SAT177D
AT-331

High Clutch (Contd)
3. 4.
Remove snap ring. Remove drive plates, driven plates and retaining plate.
SAT178D
5. 6.
Set Tool on spring retainer and remove snap ring from high clutch drum while compressing return springs. Set Tool directly above springs. Do not expand snap ring excessively. Remove spring retainer and return springs.
AAT683
Do not remove return spring from spring retainer.
SAT302E
7.
Remove piston from high clutch drum by turning it.
SAT189D
8.
SAT139E
AT-332

High Clutch (Contd)
INSPECTION NCAT0147 Reverse Clutch Snap Ring, Spring Retainer and Return GI Springs NCAT0147S01
MA EM LC
High Clutch Drive Plates

NCAT0147S02
EC FE CL MT
SAT162D
High Clutch Piston

NCAT0147S03
Make sure check balls are not fixed. Apply compressed air to check ball oil hole opposite the return spring. Make sure there is no air leakage. Apply compressed air to oil hole on return spring side to make sure air leaks past ball.
AX SU BR
SAT186D
Seal Ring Clearance

NCAT0147S04
SAT187D
Install new seal rings onto input shaft. Measure clearance between seal ring and ring groove. Standard clearance: 0.08 - 0.23 mm (0.0031 - 0.0091 in) Allowable limit: 0.23 mm (0.0091 in) If not within wear limit, replace input shaft assembly.
ST RS BT HA
ASSEMBLY
NCAT0148
SC EL IDX
SAT182DA
AT-333

High Clutch (Contd)
2.
Install piston assembly by turning it slowly. Apply ATF to inner surface of drum.
SAT189D
3.
SAT191D
4.
AAT683
Do not align snap ring gap with spring retainer stopper.
SAT193D
5. Install drive plates, driven plates and retaining plate. Take care with the order and direction of plates. 6. Install snap ring.
SAT195D
AT-334

High Clutch (Contd)
7.
Measure clearance between retaining plate and snap ring. If not within allowable limit, select proper retaining plate. Specified clearance: Standard: 1.4 - 1.8 mm (0.055 - 0.071 in) Allowable limit: 2.4 mm (0.094 in) Retaining plate: Refer to SDS, AT-390.
GI MA EM
SAT199D
LC
8. Check operation of high clutch. Refer to High Clutch, AT-331.
EC FE CL
SAT196D
MT
9. Install seal rings to input shaft. Apply petroleum jelly to seal rings.
AX SU BR
SAT197D
Roll paper around seal rings to prevent seal rings from spreading.
ST RS BT HA
SAT198D
SC EL IDX
AT-335

Forward Clutch and Overrun Clutch
Forward Clutch and Overrun Clutch

COMPONENTS
NCAT0149
SAT932J
DISASSEMBLY
1. a. b. c. Check operation of forward clutch and overrun clutch. Install bearing retainer on forward clutch drum. Apply compressed air to oil hole of forward clutch drum. Check to see that retaining plate moves to snap ring.
NCAT0150
SAT201D
d.
If retaining plate does not contact snap ring: D-ring might be damaged. Oil seal might be damaged. Fluid might be leaking past piston check ball.
SAT202D
AT-336

Forward Clutch and Overrun Clutch (Contd)
2. 3.
Remove snap ring for forward clutch. Remove drive plates, driven plates, retaining plate and dish plate for forward clutch.
GI MA EM
SAT203D
LC
4. 5. Remove snap ring for overrun clutch. Remove drive plates, driven plates, retaining plate and dish plate for overrun clutch.
EC FE CL
SAT204D
MT
6. 7. Set Tool on spring retainer and remove snap ring from forward clutch drum while compressing return springs. Set Tool directly above return springs. Do not expand snap ring excessively. Remove spring retainer and return springs.
AX SU BR
AAT685
8.
Remove forward clutch piston with overrun clutch piston from forward clutch drum by turning it.
ST RS BT HA
SAT216D
9.
Remove overrun clutch piston from forward clutch piston by turning it.
SC EL IDX
SAT215D
AT-337

10. Remove D-rings and oil seals from forward clutch piston and overrun clutch piston.
SAT140E
INSPECTION Snap Rings and Spring Retainer

Check for deformation, fatigue or damage.
Forward Clutch and Overrun Clutch Return Springs NCAT0151S02

Check for deformation or damage. Measure free length and outer diameter. Inspection standard: Refer to SDS, AT-392. Replace if deformed or fatigued.
SAT138D
Forward Clutch and Overrun Clutch Drive Plates

Check facing for burns, cracks or damage. Measure thickness of facing. Thickness of drive plate: Forward clutch Standard value: 1.8 mm (0.071 in) Wear limit: 1.6 mm (0.063 in) Overrun clutch Standard value: 1.6 mm (0.063 in) Wear limit: 1.4 mm (0.055 in) If not within wear limit, replace.
NCAT0151S03
SAT162D
AT-338

Forward Clutch and Overrun Clutch Dish Plates

Check for deformation or damage. Measure thickness of dish plate. Thickness of dish plate t: Forward clutch: 2.5 mm (0.098 in) Overrun clutch: 2.15 mm (0.0846 in) If deformed or fatigued, replace.
NCAT0151S04
GI MA EM LC
SAT163D
Forward Clutch Drum

NCAT0151S05
Make sure check balls are not fixed. Apply compressed air to check ball oil hole from outside of forward clutch drum. Make sure air leaks past ball. Apply compressed air to oil hole from inside of forward clutch drum. Make sure there is no air leakage.
EC FE CL
SAT213D
MT
Overrun Clutch Piston

NCAT0151S06
Make sure check balls are not fixed. Apply compressed air to check ball oil hole opposite the return spring. Make sure there is no air leakage. Apply compressed air to oil hole on return spring side. Make sure air leaks past ball.
AX SU BR
SAT212D
ASSEMBLY
1.
NCAT0152
Install D-rings and oil seals on forward clutch piston and overrun clutch piston. Take care with direction of oil seal. Apply ATF to both parts.
ST RS BT HA
SAT208DA
2.
Install overrun clutch piston assembly on forward clutch piston while turning it slowly. Apply ATF to inner surface of forward clutch piston.
SC EL IDX
SAT215D
AT-339

3.
Install forward clutch piston assembly on forward clutch drum while turning it slowly. Apply ATF to inner surface of drum.
SAT216D
4.
Align notch in forward clutch piston with groove in forward clutch drum.
SAT217D
5. 6.
Install return spring on piston. Install spring retainer on return springs.
SAT218D
7.
AAT685
Do not align snap ring gap with spring retainer stopper.
SAT220D
AT-340

8. 9.
Install drive plates, driven plates, retaining plate and dish plate for overrun clutch. Install snap ring for overrun clutch.
GI MA EM
SAT204D
LC
10. Measure clearance between overrun clutch retaining plate and snap ring. If not within allowable limit, select proper retaining plate. Specified clearance: Standard: 1.0 - 1.4 mm (0.039 - 0.055 in) Allowable limit: 2.0 mm (0.079 in) Overrun clutch retaining plate: Refer to SDS, AT-391.
EC FE CL MT
SAT227D
11. Install drive plates, driven plates, retaining plate and dish plate for forward clutch. Take care with the order and direction of plates. 12. Install snap ring for forward clutch.
AX SU BR
SAT203D
13. Measure clearance between forward clutch retaining plate and snap ring. If not within allowable limit, select proper retaining plate. Specified clearance: Standard: 0.45 - 0.85 mm (0.0177 - 0.0335 in) Allowable limit: 1.85 mm (0.0728 in) Forward clutch retaining plate: Refer to SDS, AT-391.
ST RS BT HA
SAT228D
14. Check operation of forward clutch. Refer to Forward Clutch and Overrun Clutch, AT-336.
SC EL IDX
SAT201D
AT-341

15. Check operation of overrun clutch. Refer to Forward Clutch and Overrun Clutch, AT-336.
SAT202D
AT-342

Low & Reverse Brake
Low & Reverse Brake

COMPONENTS
=NCAT0153
SAT486JA
MT
DISASSEMBLY
1. a. b. c.
SAT230D
NCAT0154
Check operation of low & reverse brake. Apply compressed air to oil hole of transmission case. Check to see that retaining plate moves to snap ring. If retaining plate does not contact snap ring: D-ring might be damaged. Oil seal might be damaged. Fluid might be leaking past piston check ball.
AX SU BR
2. 3. 4.
Stand transmission case. Remove snap ring. Remove drive plates, driven plates, retaining plate from transmission case.
ST RS BT HA
SAT231D
5. 6.
Set Tool on spring retainer and remove snap ring while compressing return springs. Set Tool directly above return springs. Do not expand snap ring excessively. Remove spring retainer and return springs.
SC EL IDX
AAT687
AT-343

Low & Reverse Brake (Contd)
Do not remove return springs from spring retainer.
SAT303E
7. 8.
Apply compressed air to oil hole of transmission case while holding piston. Remove piston from transmission case by turning it.
SAT234D
9.
SAT767G
INSPECTION NCAT0155 Low & Reverse Clutch Snap Ring, Spring Retainer and Return Springs NCAT0155S01
AT-344

Low & Reverse Brake Drive Plates

NCAT0155S02
GI MA EM LC
SAT162D
ASSEMBLY
NCAT0156
EC FE CL
SAT235DA
MT
2. 3. Stand transmission case. Install piston assembly on transmission case while turning it slowly. Apply ATF to inner surface of transmission case.
AX SU BR
SAT239D
4.
ST RS BT HA
SAT241D
5.
Install snap ring while compressing return springs. Set Tool directly above return springs.
SC EL IDX
AAT687
AT-345

6.
Install drive plates, driven plates, retaining plates and dished plates. Do not align the projections on the two dished plates. Make sure to put the plates in the correct order and direction.
SAT254E
7.
Install snap ring.
SAT231D
8.
Measure clearance between retaining plate and snap ring. If not within allowable limit, select proper retaining plate (front side). Specified clearance: Standard: 1.4 - 1.8 mm (0.055 - 0.071 in) Allowable limit: 2.8 mm (0.110 in) Retaining plate: Refer to SDS, AT-392.
SAT246D
9.
Check operation of low & reverse brake. Refer to DISASSEMBLY, AT-343.
SAT230D
AT-346

Rear Internal Gear, Forward Clutch Hub and Overrun Clutch Hub
Rear Internal Gear, Forward Clutch Hub and Overrun Clutch Hub
COMPONENTS
NCAT0157
SAT875J
AX SU BR
DISASSEMBLY
1. 2. Remove snap ring from overrun clutch hub. Remove overrun clutch hub from forward clutch hub.
NCAT0158
ST RS BT HA
SAT249D
3.
Remove thrust washer from forward clutch hub.
SC EL IDX
SAT250D
AT-347

Rear Internal Gear, Forward Clutch Hub and Overrun Clutch Hub (Contd)
4.
Remove forward clutch hub from rear internal gear.
SAT251D
5.
Remove end bearing from rear internal gear.
SAT252D
6.
Remove thrust washer from rear internal gear.
SAT253D
7.
Remove end bearing from forward one-way clutch.
SAT254D
8.
Remove one-way clutch from forward clutch hub.
SAT255D
AT-348

INSPECTION NCAT0159 Rear Internal Gear, Forward Clutch Hub and Overrun GI Clutch Hub NCAT0159S01
Check rubbing surfaces for wear or damage.
MA EM
SAT256D
LC
Snap Ring, End Bearings and Forward One-way Clutch NCAT0159S02
Check snap ring and end bearings for deformation and damage. Check forward one-way clutch for wear and damage.
EC FE CL
SAT257D
MT
ASSEMBLY
1.
NCAT0160
Install forward one-way clutch on forward clutch. Take care with the direction of forward one-way clutch.
AX SU BR
SAT976H
2.
Install end bearing on forward one-way clutch. Apply petroleum jelly to end bearing.
ST RS BT HA
SAT259D
3.
Install thrust washer on rear internal gear. Apply petroleum jelly to thrust washer. Align pawls of thrust washer with holes of rear internal gear.
SC EL IDX
SAT260D
AT-349

4.
Install end bearing on rear internal gear. Apply petroleum jelly to end bearing.
SAT261D
5.
Install forward clutch hub on rear internal gear. Check operation of forward one-way clutch. Hold rear internal gear and turn forward clutch hub. Check forward clutch hub for correct locking and unlocking directions. If not as shown in illustration, check installation direction of forward one-way clutch.
SAT713H
6.
Install thrust washer and overrun clutch hub. Apply petroleum jelly to thrust washer. Align pawls of thrust washer with holes of overrun clutch hub.
SAT263D
7.
Install overrun clutch hub on rear internal gear. Align projections of rear internal gear with holes of overrun clutch hub.
SAT264D
8.
Install snap ring to groove of rear internal gear.
SAT248D
AT-350

Output Shaft, Idler Gear, Reduction Pinion Gear and Bearing Retainer
Output Shaft, Idler Gear, Reduction Pinion Gear and Bearing Retainer
COMPONENTS
NCAT0161
AX SU BR
SAT487JA
ST RS BT HA
DISASSEMBLY
1.
NCAT0162
SC EL IDX
Remove seal rings from output shaft and bearing retainer.
SAT644D
AT-351

Output Shaft, Idler Gear, Reduction Pinion Gear and Bearing Retainer (Contd)
2.
Remove output shaft bearing with screwdrivers. Always replace bearing with a new one when removed. Do not damage output shaft.
SAT645D
3.
Remove snap ring from bearing retainer.
SAT646D
4.
Remove needle bearing from bearing retainer.
AAT539
5.
Remove idler gear bearing inner race from idler gear.
SAT648D
6.
Remove idler gear bearing outer race from transmission case.
AAT495
AT-352

7.
Press out reduction pinion gear bearing from reduction pinion gear.
GI MA EM
AAT538
LC
8. Remove reduction pinion gear bearing outer race from transmission case.
EC FE CL
SAT651D
MT
INSPECTION NCAT0163 Output Shaft, Idler Gear and Reduction Pinion Gear NCAT0163S01
Check shafts for cracks, wear or bending. Check gears for wear, chips and cracks.
AX SU BR
Bearing

NCAT0163S02
Make sure bearings roll freely and are free from noise, cracks, pitting or wear. When replacing taper roller bearing, replace outer and inner race as a set.
ST RS BT HA
SPD715
Seal Ring Clearance

NCAT0163S03
SC EL IDX
SAT652D
Install new seal rings to output shaft. Measure clearance between seal ring and ring groove of output shaft. Standard clearance: 0.10 - 0.25 mm (0.0039 - 0.0098 in) Allowable limit: 0.25 mm (0.0098 in) If not within allowable limit, replace output shaft. Install new seal rings to bearing retainer.
AT-353

Measure clearance between seal ring and ring groove of bearing retainer. Standard clearance: 0.10 - 0.25 mm (0.0039 - 0.0098 in) Allowable limit: 0.25 mm (0.0098 in) If not within allowable limit, replace bearing retainer.
ASSEMBLY
1.
NCAT0164
Press reduction pinion gear bearing on reduction pinion gear.
AAT688
2.
Install reduction pinion gear bearing outer race on transmission case.
SAT654D
3.
Press idler gear bearing inner race on idler gear.
AAT689
4.
Install idler gear bearing outer race on transmission case.
SAT901D
AT-354

5.
Press output shaft bearing on output shaft.
GI MA EM
SAT939D
LC
6. Press needle bearing on bearing retainer.
EC FE CL
SAT658D
MT
7. Install snap ring to bearing retainer.
AX SU BR
SAT659D
8.
After packing ring grooves with petroleum jelly, carefully install new seal rings on output shaft and bearing retainer.
ST RS BT HA
SAT660D
Roll paper around seal rings to prevent seal rings from spreading.
SC EL IDX
SAT661D
AT-355

Band Servo Piston Assembly
Band Servo Piston Assembly

COMPONENTS
NCAT0165
SAT098K
DISASSEMBLY
1. Remove band servo piston snap ring.
NCAT0166
SAT288D
2.
Apply compressed air to oil hole in transmission case to remove OD servo piston retainer and band servo piston assembly. Hold band servo piston assembly with a rag or nylon waste.
SAT289D
3.
Apply compressed air to oil hole in OD servo piston retainer to remove OD servo piston from retainer. Hold OD servo piston while applying compressed air.
SAT290DB
AT-356

Band Servo Piston Assembly (Contd)
4.
Remove D-ring from OD servo piston.
GI MA EM
SAT593GB
LC
5. Remove O-rings from OD servo piston retainer.
EC FE CL
SAT292DA
MT
6. Remove band servo piston assembly from servo piston retainer by pushing it forward.
AX SU BR
SAT293D
7.
Place piston stem end on a wooden block. While pushing servo piston spring retainer down, remove E-ring.
ST RS BT HA
SAT294D
8.
Remove OD servo return spring, band servo thrust washer and band servo piston stem from band servo piston.
SC EL IDX
SAT295DA
AT-357

9.
Remove O-rings from servo piston retainer.
SAT296DA
10. Remove D-rings from band servo piston.
SAT594GA
INSPECTION Pistons, Retainers and Piston Stem
Check frictional surfaces for abnormal wear or damage.
SAT298DA
Return Springs
Check for deformation or damage. Measure free length and outer diameter. Band servo inspection standard: Refer to SDS, AT-399.
NCAT0167S02
SAT138D
ASSEMBLY
1. Install D-rings to servo piston retainer. Apply ATF to O-rings. Pay attention to position of each O-ring.
NCAT0168
SAT595GA
AT-358

2.
Install band servo piston stem, band servo thrust washer, OD servo return spring and spring retainer to band servo piston.
GI MA EM
SAT295DA
LC
3. Place piston stem end on a wooden block. While pushing servo piston spring retainer down, install E-ring.
EC FE CL
SAT301D
MT
4. Install O-rings to servo piston retainer. Apply ATF to O-rings. Pay attention to the positions of the O-rings.
AX SU BR
SAT296DA
5.
Install band servo piston assembly to servo piston retainer by pushing it inward.
ST RS BT HA
SAT303D
6.
Install D-ring to OD servo piston. Apply ATF to D-ring.
SC EL IDX
SAT596GB
AT-359

7.
Install O-rings to OD servo piston retainer. Apply ATF to O-rings. Pay attention to the positions of the O-rings.
SAT292DA
8.
Install OD servo piston to OD servo piston retainer.
SAT306DA
9.
Install band servo piston assembly and 2nd servo return spring to transmission case. Apply ATF to O-ring of band servo piston and transmission case.
SAT307DA
10. Install OD servo piston assembly to transmission case. Apply ATF to O-ring of band servo piston and transmission case.
AAT692
11. Install band servo piston snap ring to transmission case.
SAT288D
AT-360

Final Drive
Final Drive
COMPONENTS
NCAT0169
SAT145IC
MT
DISASSEMBLY
1. Remove final gear.
NCAT0170
AX SU BR
SMT696B
2.
Press out differential side bearings.
ST RS BT HA
SAT312D
SC EL IDX
SMT697B
AT-361

Final Drive (Contd)
3.
Remove viscous coupling RE4F03W.
SMT698B
4.
Remove speedometer drive gear.
SAT313D
5.
Drive out pinion mate shaft lock pin.
SAT904D
6. 7.
Draw out pinion mate shaft from differential case. Remove pinion mate gears and side gears.
SAT316D
AT-362

Final Drive (Contd)
INSPECTION Gear, Washer, Shaft and Case

Check mating surfaces of differential case, side gears, pinion mate gears and viscous coupling. Check washers for wear.
SAT865DB
MT
Viscous Coupling RE4F03W
Check case for cracks. Check silicone oil for leakage.
NCAT0171S02
AX SU BR
SMT508B
Bearings

NCAT0171S03
Make sure bearings roll freely and are free from noise, cracks, pitting or wear. When replacing taper roller bearing, replace outer and inner race as a set.
ST RS BT HA
SPD715
ASSEMBLY RE4F03B
1. 2.
SAT318D
SC EL IDX
Install side gear and thrust washers in differential case. Install pinion mate gears and thrust washers in differential case while rotating them. When inserting, be careful not to damage pinion mate gear washers. Apply ATF to any parts.
AT-363

Final Drive (Contd)
3. a. b.
Measure clearance between side gear and differential case with washers using the following procedure. Set Tool and dial indicator on side gear. Move side gear up and down to measure dial indicator deflection. Always measure indicator deflection on both side gears. Clearance between side gear and differential case with washers: 0.1 - 0.2 mm (0.004 - 0.008 in)
SAT902D
c.
If not within specification adjust clearance by changing thickness of side gear thrust washers. Side gear thrust washer: Refer to SDS, AT-393.
SMT616
4.
Install lock pin. Make sure that lock pin is flush with case.
SAT904D
5.
Install side gear (viscous coupling side) on differential case and then install viscous coupling RE4F03W.
SMT711B
6.
Install speedometer drive gear on differential case. Align the projection of speedometer drive gear with the groove of differential case.
SAT313D
AT-364

Final Drive (Contd)
7.
Install final gear and tighten fixing bolts in numerical order.
GI MA EM
SAT326D
LC
8. Press on differential side bearings.
EC FE CL
SMT700B
MT
RE4F03W
1. 2.
NCAT0172S02
Install side gear and thrust washers in differential case. Install pinion mate gears and thrust washers in differential case while rotating them. When inserting, be careful not to damage pinion mate gear washers. Apply ATF to any parts.
AX SU BR
SAT318D
3.
Measure clearance between side gear and differential case & viscous coupling with washers using the following procedure: Differential Case Side NCAT0172S0201 1) Set Tool and dial indicator on side gear. 2) Move side gear up and down to measure dial indicator deflection. Clearance between side gear and differential case with washers: 0.1 - 0.2 mm (0.004 - 0.008 in) 3) If not within specification adjust clearance by changing thickness of side gear thrust washer. Side gear thrust washers for differential case side: Refer to SDS, AT-393.
SAT903DA
AT-365

Final Drive (Contd)
Viscous Coupling Side NCAT0172S0202 1) Place side gear and thrust washer on pinion mate gears installed on differential case. 2) Measure dimension X. Measure dimension X in at least two places.
SMT753B
3)
4)
Measure dimension Y. Measure dimension Y in at least two places. Clearance between side gear and viscous coupling = X + Y 2A: 0.1 - 0.2 mm (0.004 - 0.008 in) A: Height of gauge If not within specification, adjust clearance by changing thickness of side gear thrust washer. Side gear thrust washers for viscous coupling side: Refer to SDS, AT-393.
SMT754B
4.
Install lock pin. Make sure that lock pin is flush with case.
SAT904D
AT-366

Final Drive (Contd)
5.
Install side gear (viscous coupling side) on differential case and then install viscous coupling RE4F03W.
GI MA EM
SMT711B
LC
6. Install speedometer drive gear on differential case. Align the projection of speedometer drive gear with the groove of differential case.
EC FE CL
SAT313D
MT
7. Install final gear and tighten fixing bolts in numerical order.
AX SU BR
SAT326D
8.
Press on differential side bearings.
ST RS BT HA
SMT700B
SC EL IDX
AT-367
ASSEMBLY
Assembly (1)
Assembly (1)
1. Install revolution sensor onto transmission case. Always use new sealing parts.
NCAT0173
SAT311G
2.
Install differential side oil seals on transmission case and converter housing, so that A and B are within specifications.
AAT695
Unit: mm (in) A 5.5 - 6.5 (0.217 - 0.256) B 0.5 to 0.5 (0.020 to 0.020)
SAT489JE
3.
Install parking actuator support to transmission case. Pay attention to direction of parking actuator support.
SAT328D
4.
Install parking pawl on transmission case and fix it with parking shaft.
SAT329D
AT-368
ASSEMBLY
Assembly (1) (Contd)
5.
Install return spring.
GI MA EM
SAT330D
LC
Adjustment (1)
DIFFERENTIAL SIDE BEARING PRELOAD
1. 2.
EC FE CL
Install differential side bearing outer race without adjusting shim on transmission case. Install differential side bearing outer race on converter housing.
SAT947DA
MT
3. 4. Place final drive assembly on transmission case. Install transmission case on converter housing. Tighten transmission case fixing bolts A and B to the specified torque.
AX SU BR
SAT027D
5. 6. 7.
8.
Attach dial indicator on differential case at transmission case side. Insert Tool into differential side gear from converter housing. Move Tool up and down and measure dial indicator deflection. Differential side bearing preload T: 0.04 - 0.09 mm (0.0016 - 0.0035 in) Select proper thickness of differential side bearing adjusting shim(s) using SDS table as a guide. Differential side bearing adjusting shim: Refer to SDS, AT-394.
AAT947
AT-369
ASSEMBLY
Adjustment (1) (Contd)
9. Remove converter housing from transmission case. 10. Remove final drive assembly from transmission case. 11. Remove differential side bearing outer race from transmission case. 12. Reinstall differential side bearing outer race and shim(s) selected from SDS table on transmission case. 13. Reinstall converter housing on transmission case and tighten transmission case fixing bolts to the specified torque.
AAT477
14. Insert Tool into differential case and measure turning torque of final drive assembly. Turn final drive assembly in both directions several times to seat bearing rollers correctly. Turning torque of final drive assembly (New bearing): 0.49 - 1.08 Nm (5.0 - 11.0 kg-cm, 4.3 - 9.5 in-lb) When old bearing is used again, turning torque will be slightly less than the above. Make sure torque is close to the specified range.
AAT466
REDUCTION PINION GEAR BEARING PRELOAD

NCAT0174S02
Be sure to remove final drive assembly before doing this procedure. Using caliper and straightedge, calculate a dimention T (adjuster shim thickness) in the left figure by the following formula. And adjust the inspection standard for pre-load (rotating slide torque) as shown below. T=AE Inspection standard for preload: 0.1 - 0.69 Nm (1.1 - 7.0 kg-cm, 0.95 - 6.08 in-lb) Remove transmission case and final drive assembly from converter housing. Select proper thickness of reduction pinion gear bearing adjusting shim using the following procedures. Place reduction pinion gear on transmission case as shown.
SAT876J
1. 2. a.
SAT332DA
b. c.
Place idler gear bearing on transmission case. Measure dimensions B, C and D and calculate dimension A. A = D (B + C) A: Distance between the surface of idler gear bearing inner race and the adjusting shim mating surface of reduction pinion gear.
SAT333DA
AT-370
ASSEMBLY
Measure dimension B between the end of reduction pinion gear and the surface of transmission case. Measure dimension B in at least two places.
GI MA EM
SAT334DA
LC
Measure dimension C between the surface of idler gear bearing inner race and the surface of transmission case. Measure dimension C in at least two places.
EC FE CL
SAT335D
MT
Measure dimension D between the end of reduction pinion gear and the adjusting shim mating surface of reduction pinion gear. Measure dimension D in at least two places. Calculate dimension A. A = D (B + C)
AX SU BR
SAT336DA
d.
Measure dimension E between the end of idler gear and the idler gear bearing inner race mating surface of idler gear. Measure dimension E in at least two places.
ST RS BT HA
SAT337D
e.
Calculate T and select proper thickness of reduction pinion gear bearing adjusting shim using SDS table as a guide. T = A E 0.05 mm (0.0020 in)* Reduction pinion gear bearing adjusting shim: Refer to SDS, AT-397. *: Bearing preload
SC EL IDX
AT-371
ASSEMBLY
3. 4. 5.
Install reduction pinion gear and reduction pinion gear bearing adjusting shim selected in step 2-e on transmission case. Press idler gear bearing inner race on idler gear. Press idler gear on reduction pinion gear. Press idler gear so that idler gear can be locked by parking pawl.
AAT696
6.
Tighten idler gear lock nut to the specified torque. Lock idler gear with parking pawl when tightening lock nut.
SAT339D
7.
Measure turning torque of reduction pinion gear. When measuring turning torque, turn reduction pinion gear in both directions several times to seat bearing rollers correctly. Turning torque of reduction pinion gear: 0.1 - 0.69 Nm (1.1 - 7.0 kg-cm, 0.95 - 6.08 in-lb)
SAT340DC
OUTPUT SHAFT END PLAY

NCAT0174S03
Measure clearance between side cover and the end of the output shaft bearing. Select proper thickness of adjusting shim so that clearance is within specifications.
SAT341D
1.
Install bearing retainer for output shaft.
SAT347D
AT-372
ASSEMBLY
2.
Install output shaft thrust needle bearing on bearing retainer.
GI MA EM
SAT438D
LC
3. Install output shaft on transmission case.
EC FE CL
SAT439D
MT
4. Measure dimensions 1 and 2 at side cover and then calculate dimension A. Measure dimension 1 and 2 in at least two places A: Distance between transmission case fitting surface and adjusting shim mating surface A= 1 2 2: Height of gauge
AX SU BR
SAT874DA
5.
Measure dimensions 2 and 3 and then calculate dimension B. Measure 2 and 3 in at least two places. B: Distance between the end of output shaft bearing outer race and the side cover fitting surface of transmission case B= 2 3 2: Height of gauge
ST RS BT HA
SAT875DA
6.
7.
Select proper thickness of adjusting shim so that output shaft end play (clearance between side cover and output shaft bearing) is within specifications. Output shaft end play (A B): 0 - 0.5 mm (0 - 0.020 in) Output shaft end play adjusting shim: Refer to SDS, AT-398. Install adjusting shim on output shaft bearing.
SC EL IDX
SAT440D
AT-373
ASSEMBLY
8.
Apply locking sealant to transmission case as shown in illustration.
SAT441D
9.
Install side cover on transmission case. Apply locking sealant to the mating surface of transmission case.
SAT442D
10. Tighten side cover fixing bolts to specified torque. Do not mix bolts A and B. Always replace bolts A as they are self-sealing bolts.
SAT124E
Assembly (2)
1. 2. Remove paper rolled around bearing retainer. Install thrust washer on bearing retainer. Apply petroleum jelly to thrust washer.
NCAT0175
SAT354D
3.
Install forward clutch assembly. Align teeth of low & reverse brake drive plates before installing. Make sure that bearing retainer seal rings are not spread.
SAT355D
AT-374
ASSEMBLY
4.
Install thrust needle bearing on bearing retainer. Apply petroleum jelly to thrust bearing. Pay attention to direction of thrust needle bearing.
GI MA EM
SAT356D
LC
5. Install thrust needle bearing on rear internal gear. Apply petroleum jelly to thrust needle bearing. Pay attention to direction of thrust needle bearing.
EC FE CL
SAT357D
MT
6. Hold forward clutch hub and turn overrun clutch hub. Check overrun clutch hub for directions of lock and unlock. If not as shown in illustration, check installed direction of forward one-way clutch.
AX SU BR
SAT358D
7.
Install rear internal gear assembly. Align teeth of forward clutch and overrun clutch drive plate.
ST RS BT HA
SAT359D
8.
Install needle bearing on rear planetary carrier. Apply petroleum jelly to needle bearing. Pay attention to direction of needle bearing.
SC EL IDX
SAT360D
AT-375
ASSEMBLY
9.
Install rear sun gear on rear planetary carrier. Pay attention to direction of rear sun gear.
SAT052D
10. Install rear planetary carrier on transmission case.
SAT362D
11. Install thrust needle bearing on front planetary carrier. Apply petroleum jelly to thrust needle bearing. Pay attention to direction of thrust needle bearing.
SAT363D
12. Install low one-way clutch to front planetary carrier by turning it in the direction of the arrow as shown. 13. While holding front planetary carrier, turn low one-way clutch. Check low one-way clutch for correct directions of lock and unlock.
SAT048D
14. Install front planetary carrier assembly on transmission case.
SAT047D
AT-376
ASSEMBLY
15. Install snap ring with screwdriver. Forward clutch and bearings must be correctly installed for snap ring to fit groove of transmission case.
GI MA EM
SAT046D
LC
16. Install needle bearing on front sun gear. Apply petroleum jelly to needle bearing. Pay attention to direction of needle bearing.
EC FE CL
SAT367D
MT
17. Install front sun gear on front planetary carrier.
AX SU BR
SAT368D
18. Install needle bearing on front sun gear. Apply petroleum jelly to needle bearing. Pay attention to direction of needle bearing.
ST RS BT HA
SAT369D
19. Install high clutch hub on front sun gear.
SC EL IDX
SAT370D
AT-377
ASSEMBLY
20. Install needle bearing on high clutch hub. Apply petroleum jelly to needle bearing. Pay attention to direction of needle bearing.
SAT371D
21. Remove paper rolled around input shaft. 22. Install input shaft assembly. Align teeth of high clutch drive plates before installing.
SAT372D
23. Install reverse clutch assembly. Align teeth of reverse clutch drive plates before installing.
SAT373D
Adjustment (2)
NCAT0176
When any parts listed below are replaced, adjust total end play and reverse clutch end play.
Part name Transmission case Overrun clutch hub Rear internal gear Rear planetary carrier Rear sun gear Front planetary carrier Front sun gear High clutch hub High clutch drum Oil pump cover Reverse clutch drum Total end play Reverse clutch end play
AT-378
ASSEMBLY
TOTAL END PLAY

NCAT0176S01
Measure clearance between reverse clutch drum and needle bearing for oil pump cover. Select proper thickness of bearing race so that end play is within specifications.
GI MA EM
SAT374D
LC
1. Measure dimensions K and L and then calculate dimension J.
EC FE CL
SAT375D
MT
a. Measure dimension K.
AX SU BR
SAT376D
b. c.
Measure dimension L. Calculate dimension J. J: Distance between oil pump fitting surface of transmission case and needle bearing mating surface of high clutch drum J=KL
ST RS BT HA
SAT377D
2. a.
Measure dimension M. Place bearing race and needle bearing on oil pump assembly.
SC EL IDX
SAT378D
AT-379
ASSEMBLY
b.
Measure dimension M. M: Distance between transmission case fitting surface and needle bearing on oil pump cover M1: Indication of gauge
SAT379D
c.
Measure thickness of straightedge t. M = M1 t
SAT443D
3.
Adjust total end play T3. T3 = J M Total end play T3: 0.25 - 0.55 mm (0.0098 - 0.0217 in) Select proper thickness of bearing race so that total end play is within specifications. Bearing races: Refer to SDS, AT-399.
REVERSE CLUTCH END PLAY

NCAT0176S02
Measure clearance between oil pump cover and thrust washer for reverse clutch drum. Select proper thickness of thrust washer so that end play is within specifications.
SAT380D
1.
Measure dimensions O and P and then calculate dimension N.
SAT381D
AT-380
ASSEMBLY
a. b.
Place thrust washer on reverse clutch drum. Measure dimension O.
GI MA EM
SAT382D
LC
c. d. Measure dimension P. Calculate dimension N. N: Distance between oil pump fitting surface of transmission case and thrust washer on reverse clutch drum N=OP
EC FE CL
SAT383D
MT
2. Measure dimensions R and S and then calculate dimension Q.
AX SU BR
SAT384D
a.
Measure dimension R.
ST RS BT HA
SAT385D
b. c.
Measure dimension S. Calculate dimension Q. Q: Distance between transmission case fitting surface and thrust washer mating surface Q=RS
SC EL IDX
SAT386D
AT-381
ASSEMBLY
3.
Adjust reverse clutch end play T4. T4 = N Q Reverse clutch end play: 0.65 - 1.00 mm (0.0256 - 0.0394 in) Select proper thickness of thrust washer so that reverse clutch end play is within specifications. Thrust washer: Refer to SDS, AT-399.
Assembly (3)
1. 2.
NCAT0177
Remove reverse clutch assembly and install needle bearing on high clutch assembly. Pay attention to direction of needle bearing. Install reverse clutch assembly.
SAT387D
3. 4.
Install anchor end pin and lock nut on transmission case. Place brake band on outside of reverse clutch drum. Tighten anchor end pin just enough so that brake band is evenly fitted on reverse clutch drum.
SAT038D
5.
Place bearing race selected in total end play adjustment step on oil pump cover. Apply petroleum jelly to bearing race.
SAT389D
6.
Place thrust washer selected in reverse clutch end play step on reverse clutch drum. Apply petroleum jelly to thrust washer.
SAT390D
AT-382
ASSEMBLY
7.
Install oil pump assembly on transmission case.
GI MA EM
SAT391D
LC
8. Tighten oil pump fixing bolts to specified torque.
EC FE CL
SAT392D
MT
9. Install O-ring to input shaft. Apply ATF to O-ring.
AX SU BR
SAT034D
10. Adjust brake band. a. Tighten anchor end pin to specified torque. Anchor end pin: : 3.9 - 5.9 Nm (0.4 - 0.6 kg-m, 35 - 52 in-lb)
ST RS BT HA
SAT394D
b.
Back off anchor end pin two and a half turns.
SC EL IDX
SAT395D
AT-383
ASSEMBLY
c.
While holding anchor end pin, tighten lock nut.
SAT396D
11. Apply compressed air to oil holes of transmission case and check operation of brake band.
SAT397D
Assembly (4)
1. Install final drive assembly on transmission case.
NCAT0178
SAT030D
2.
Install oil tube on converter housing.
SAT033DA
AT-384
ASSEMBLY
3. 4.
Install O-ring on differential oil port of transmission case. Install converter housing on transmission case. Apply locking sealant to mating surface of converter housing.
Bolt A B Length mm (in) 32.8 (1.291) 40 (1.57)
SAT405D
MT
5. a. Install accumulator piston. Check contact surface of accumulator piston for damage.
AX SU BR
SAT406DA
b.
Install O-rings on accumulator piston. Apply ATF to O-rings. Accumulator piston O-rings: Refer to SDS, AT-399.
ST RS BT HA
SAT407DA
c.
Install accumulator pistons and return springs on transmission case. Apply ATF to inner surface of transmission case. Return springs: Refer to SDS, AT-399.
SC EL IDX
SAT878J
AT-385
ASSEMBLY
6.
Install lip seals for band servo oil holes on transmission case. Apply petroleum jelly to lip seals.
SAT021D
SAT022D
7. a.
Install control valve assembly. Insert manual valve into control valve assembly. Apply ATF to manual valve.
SAT017D
b. c.
Pass solenoid harness through transmission case and install terminal body on transmission case by pushing it. Install stopper ring to terminal body.
AAT261A
AT-386
ASSEMBLY
Tighten bolts A, B and C. : 7 - 9 Nm (0.7 - 0.9 kg-m, 61 - 78 in-lb) Bolt length, number and location
Bolt symbol Bolt length Number of bolts A 40.0 mm (1.575 in) 5 B 33.0 mm (1.299 in) 6 C 43.5 mm (1.713 in) 2
d.
AAT260A
MT
8. a. Install oil pan. Attach magnet to oil pan.
AX SU BR
SAT418D
b. c. d.
Install new oil pan gasket on transmission case. Install oil pan on transmission case. Always replace oil pan bolts as they are self-sealing bolts. Tighten the four bolts in a criss-cross pattern to prevent dislocation of gasket. Tighten drain plug to specified torque.
ST RS BT HA
SAT128E
9. a. b. c.
Install PNP switch. Set manual shaft in P position. Temporarily install PNP switch on manual shaft. Move selector lever to N position.
SC EL IDX
SAT023JB
AT-387
ASSEMBLY
d. 1) 2) e. f.
Use a 4 mm (0.157 in) pin for this adjustment. Insert the pin straight into the manual shaft adjustment hole. Rotate PNP switch until the pin can also be inserted straight into hole in PNP switch. Tighten PNP switch fixing bolts. Remove pin from adjustment hole after adjusting PNP switch.
SAT426DB
10. Install oil charging pipe and oil cooler tube to transmission case.
SAT586H
11. Install torque converter. a. Pour ATF into torque converter. Approximately 1 liter (1-1/8 US qt, 7/8 Imp qt) of fluid is required for a new torque converter. When reusing old torque converter, add the same amount of fluid as was drained.
SAT428DA
b.
Install torque converter while aligning notches of torque converter with notches of oil pump.
SAT429D
c.
Measure distance A to check that torque converter is in proper position. Distance A: 15.9 mm (0.626 in) or more
SAT430D
AT-388
SERVICE DATA AND SPECIFICATIONS (SDS)

General Specifications
General Specifications
Engine Automatic transaxle model Automatic transaxle assembly Model code number 1st 2nd 3rd Transaxle gear ratio 4th Reverse Final drive Recommended fluid Fluid capacity 0.697 2.310 4.072 RE4F03B 3AX11 2.861 1.562 1.000 SR20DE RE4F03W 3AX17
NCAT0179
Nissan Matic D (Continental U.S. and Alaska) or Genuine Nissan Automatic Transmission Fluid (Canada)*1 7.0 (7-3/8 US qt, 6-1/8 Imp qt)
*1: Refer to MA-11, Fluids and Lubricants.
Shift Schedule
VEHICLE SPEED WHEN SHIFTING GEARS
Throttle position Shift pattern Comfort Vehicle speed km/h (MPH) D 1 , D2 51 - 59 (32 - 37) 33 - 41 (21 - 25) D2 , D 3 97 - 105 (60 - 65) 58 - 66 (36 - 41) D3 , D 4 153 - 161 (95 - 100) 121 - 129 (75 - 80) D4 , D 3 149 - 157 (93 - 98) 72 - 80 (45 - 50) D3 , D 2 87 - 95 (54 - 59) 34 - 42 (21 - 26) D2 , D 1 41 - 49 (25 - 30) 9 - 17 (6 - 11)
MT
12 , 1 1 51 - 59 (32 - 37) 51 - 59 (32 - 37)
Full throttle
AX SU
Half throttle
Comfort
VEHICLE SPEED WHEN PERFORMING LOCK-UP

Vehicle speed km/h (MPH) Throttle opening OD switch ON (D4) 2/8 OFF (D3) Comfort 86 - 94 (53 - 58) Shift pattern Lock-up ON Comfort 105 - 113 (65 - 70)
NCAT0180S02
BR ST RS BT
NCAT0182
Lock-up OFF 74 - 82 (46 - 51) 83 - 91 (52 - 57)
Stall Revolution
Engine model SR20DE Stall revolution 2,350 - 2,850 rpm
NCAT0181
Line Pressure
Engine speed rpm Idle Stall Line pressure kPa (kg/cm , psi) R position 778 (7.9, 113) 1,820 (18.5, 263) D position 500 (5.1, 73) 1,170 (11.9, 169) 2 position 500 (5.1, 73) 1,170 (11.9, 169) 1 position 500 (5.1, 73) 1,170 (11.9, 169)
2
HA SC EL IDX
AT-389

Control Valves
Control Valves
CONTROL VALVE AND PLUG RETURN SPRINGS
No. 35 19 Upper body Refer to Control Valve Upper Body, AT-321. 23 15 28 33 2 7 10 Parts 3-2 timing valve spring Cooler check valve spring Pilot valve spring 1-2 accumulator valve spring 1-2 accumulator piston spring 1st reducing valve spring Overrun clutch reducing valve spring Torque converter relief valve spring Torque converter clutch control valve spring Shuttle valve spring Pressure regulator valve spring Overrun clutch control valve spring Accumulator control valve spring Shift valve A spring Shift valve B spring Pressure modifier valve spring 7 Oil cooler relief valve spring T/C pressure spring 31742-80X16 31872-31X00 31742-3AX07 32.0 (1.260) 17.02 (0.6701) 9.0 (0.354) 6.9 (0.272) 8.0 (0.315) 7.3 (0.287) Part No.* 31736-01X00 31742-3AX05 31742-3AX03 31742-3AX00 31742-3AX09 31742-80X05 31742-80X06 31742-3AX04 31742-3AX02 Free length 23.0 (0.906) 28.04 (1.1039) 38.98 (1.5346) 20.5 (0.807) 55.66 (2.1913) 27.0 (1.063) 37.5 (1.476) 33.3 (1.3110) 53.01 (2.0870)
Unit: mm (in)
Outer diameter 6.65 (0.2618) 7.15 (0.2815) 8.9 (0.350) 6.95 (0.2736) 19.5 (0.7677) 7.0 (0.276) 7.0 (0.276) 9.0 (0.354) 6.5 (0.256)
34 18 23 Lower body Refer to Control Valve Lower Body, AT-325. 27 29 2 11
31762-41X04 31742-80X13 31762-80X00 31742-80X02 31762-80X00 31762-80X00 31742-41X15
51.0 (2.0079) 45.0 (1.772) 21.7 (0.854) 22.0 (0.866) 21.7 (0.854) 21.7 (0.854) 30.5 (1.201)
5.65 (0.2224) 15.0 (0.591) 7.0 (0.276) 6.5 (0.256) 7.0 (0.276) 7.0 (0.276) 9.8 (0.386)
*: Always check with the Parts Department for the latest parts information.
Clutch and Brakes

REVERSE CLUTCH
Number of drive plates Number of driven plates Standard Drive plate thickness mm (in) Allowable limit Standard Clearance mm (in) Allowable limit Thickness mm (in) 4.4 4.6 4.8 5.0 5.2 (0.173) (0.181) (0.189) (0.197) (0.205) 1.2 (0.047) Part number* 31537-31X00 31537-31X01 31537-31X02 31537-31X03 31537-31X04 1.8 (0.071) 0.5 - 0.8 (0.020 - 0.031) 2 2 2.0 (0.079)
Thickness of retaining plates
HIGH CLUTCH
Number of drive plates Number of driven plates 3 5
NCAT0184S02
AT-390

Clutch and Brakes (Contd)
Standard Drive plate thickness mm (in) Allowable limit Standard Clearance mm (in) Allowable limit Thickness mm (in) 4.8 5.0 5.2 5.4 5.6 5.8 6.0 (0.189) (0.197) (0.205) (0.213) (0.220) (0.228) (0.236) 2.4 (0.094) Part number* 31537-32X05 31537-32X06 31537-32X07 31537-32X08 31537-32X09 31537-32X10 31537-32X11 1.8 (0.071) 1.4 - 1.8 (0.055 - 0.071) 2.0 (0.079)
GI MA EM LC EC
NCAT0184S03
Thickness of retaining plates
FORWARD CLUTCH
Number of drive plates Number of driven plates Standard Drive plate thickness mm (in) Allowable limit Standard Clearance mm (in) Allowable limit Thickness mm (in) 3.6 3.8 4.0 4.2 4.4 4.6 (0.142) (0.150) (0.157) (0.165) (0.173) (0.181) 1.85 (0.0728) Part number* 31537-31X60 31537-31X61 31537-31X62 31537-31X63 31537-31X64 31537-31X65 1.6 (0.063) 0.45 - 0.85 (0.0177 - 0.0335) 5 5 1.8 (0.071)
FE CL MT
AX SU BR
NCAT0184S04
Thickness of retaining plate
OVERRUN CLUTCH
Number of drive plates Number of driven plates Standard Drive plate thickness mm (in) Allowable limit Standard Clearance mm (in) Allowable limit Thickness mm (in) 3.6 3.8 4.0 4.2 4.4 (0.142) (0.150) (0.157) (0.165) (0.173) 2.0 (0.079) Part number* 31567-31X79 31567-31X80 31567-31X81 31567-31X82 31567-31X83 1.4 (0.055) 1.0 - 1.4 (0.039 - 0.055) 3 4 1.6 (0.063)
AT-391

Clutch and Brakes (Contd)
LOW & REVERSE BRAKE

Number of drive plates Number of driven plates Standard Drive plate thickness mm (in) Allowable limit Standard Clearance mm (in) Allowable limit Thickness mm (in) 3.6 3.8 4.0 4.2 4.4 4.6 (0.142) (0.150) (0.157) (0.165) (0.173) (0.181) 2.8 (0.110) Part number* 31667-31X16 31667-31X17 31667-31X18 31667-31X19 31667-31X20 31667-31X21 1.8 (0.071) 1.4 - 1.8 (0.055 - 0.071) 5 4+1 2.0 (0.079)
NCAT0184S05
BRAKE BAND
Anchor end pin tightening torque Number of returning revolutions for anchor end pin Lock nut tightening torque 3.5 - 5.8 Nm (0.35 - 0.6 kg-m, 31 - 52 in-lb) 2.50.125 31 - 36 Nm (3.2 - 3.7 kg-m, 23 - 27 ft-lb)
NCAT0184S06
Clutch and Brake Return Springs

Parts Outer (16 pcs) Forward clutch (Overrun clutch) Inner (16 pcs) Reverse clutch (16 pcs) High clutch (12 pcs) Low reverse brake (20 pcs) 26.3 (1.035) 18.6 (0.732) 19.7 (0.776) 25.1 (0.988) 7.7 (0.303) 8.0 (0.315) 11.1 (0.437) 7.6 (0.299) 31505-31X03 31505-31X00 31505-31X01 31505-31X04 Free length 26.6 (1.047) Outer diameter 10.6 (0.417) Part number* 31505-31X02
NCAT0185
Unit: mm (in)
Oil Pump
Oil pump side clearance mm (in) 0.02 - 0.04 (0.0008 - 0.0016) Inner gear Thickness mm (in) 9.99 - 10.00 (0.3933 - 0.3937) 9.98 - 9.99 (0.3929 - 0.3933) 9.97 - 9.98 (0.3925 - 0.3929) Thickness of inner gears and outer gears Outer gear Thickness mm (in) 9.99 - 10.00 (0.3933 - 0.3937) 9.98 - 9.99 (0.3929 - 0.3933) 9.97 - 9.98 (0.3925 - 0.3929) Clearance between oil pump housing and outer gear mm (in) Oil pump cover seal ring clearance mm (in) Standard Allowable limit Standard Allowable limit Part number* 31347-31X00 31347-31X01 31347-31X02 Part number* 31346-31X00 31346-31X01 31346-31X02
NCAT0186
0.08 - 0.15 (0.0031 - 0.0059) 0.15 (0.0059) 0.1 - 0.25 (0.0039 - 0.0098) 0.25 (0.0098)
AT-392

Oil Pump (Contd)
Input Shaft
Standard Input shaft seal ring clearance Allowable limit 0.23 (0.0091) 0.08 - 0.23 (0.0031 - 0.0091)
NCAT0187
GI MA EM
Unit: mm (in)
Planetary Carrier
Clearance between planetary carrier and pinion washer Standard Allowable limit 0.15 - 0.70 (0.0059 - 0.0276) 0.80 (0.0315)
NCAT0188
Unit: mm (in)
LC EC
Final Drive
DIFFERENTIAL SIDE GEAR CLEARANCE
Clearance between side gear and differential case with washer 0.1 - 0.2 mm (0.004 - 0.008 in)
FE CL MT
DIFFERENTIAL SIDE GEAR THRUST WASHERS (FOR RE4F03B)

Thickness mm (in) 0.75 0.80 0.85 0.90 0.95 0.80 0.85 0.90 0.95 1.00 (0.0295 (0.0315 (0.0335 (0.0354 (0.0374 0.0315) 0.0335) 0.0354) 0.0374) 0.0394) Part number* 38424-D2111 38424-D2112 38424-D2113 38424-D2114 38424-D2115
NCAT0189S02
DIFFERENTIAL SIDE GEAR THRUST WASHER (FOR RE4F03W)

Location Thickness mm (in) 0.75 0.80 0.85 0.90 0.95 0.80 0.85 0.90 0.95 1.00 (0.0295 (0.0315 (0.0335 (0.0354 (0.0374 0.0315) 0.0335) 0.0354) 0.0374) 0.0394) Differential case side Part number* 38424-D2111 38424-D2112 38424-D2113 38424-D2114 38424-D2115 Viscous coupling side Part number* 38424-D2110 38424-D2111 38424-D2112 38424-D2113 38424-D2114 38424-D2115 38424-D2116 38424-D2117 38424-D2118 38424-D2119 38424-D2120 38424-D2121 38424-D2122
AX
NCAT0189S07
NCAT0189S03
Location Thickness mm (in) 0.70 0.75 0.80 0.85 0.90 0.95 1.00 1.05 1.10 1.15 1.20 1.25 1.30 0.75 0.80 0.85 0.90 0.95 1.00 1.05 1.10 1.15 1.20 1.25 1.30 1.35 (0.0276 (0.0295 (0.0315 (0.0335 (0.0354 (0.0374 (0.0394 (0.0413 (0.0433 (0.0453 (0.0472 (0.0492 (0.0512 0.0295) 0.0315) 0.0335) 0.0354) 0.0374) 0.0394) 0.0413) 0.0433) 0.0453) 0.0472) 0.0492) 0.0512) 0.0531)
BEARING PRELOAD
Differential side bearing preload T 0.04 - 0.09 mm (0.0016 - 0.0035 in)
IDX
AT-393

Final Drive (Contd)
TURNING TORQUE
Turning torque of final drive assembly 0.49 - 1.08 Nm (5.0 - 11.0 kg-cm, 4.3 - 9.5 in-lb)
NCAT0189S04
DIFFERENTIAL SIDE BEARING ADJUSTING SHIMS (FOR RE4F03B)

Thickness mm (in) 0.40 0.44 0.48 0.52 0.56 0.60 0.64 0.68 0.72 0.76 0.80 0.84 0.88 0.92 1.44 (0.0157) (0.0173) (0.0189) (0.0205) (0.0220) (0.0236) (0.0252) (0.0268) (0.0283) (0.0299) (0.0315) (0.0331) (0.0346) (0.0362) (0.0567) Part number* 31499-21X07 31499-21X08 31499-21X09 31499-21X10 31499-21X11 31499-21X12 31499-21X13 31499-21X14 31499-21X15 31499-21X16 31499-21X17 31499-21X18 31499-21X19 31499-21X20 31499-21X21
NCAT0189S05
DIFFERENTIAL SIDE BEARING ADJUSTING SHIMS (FOR RE4F03W)

Thickness mm (in) 0.28 (0.0110) 0.32 (0.0126) 0.36 (0.0142) 0.40 (0.0157) 0.44 (0.0173) 0.48 (0.0189) 0.52 (0.0205) 0.56 (0.0220) 0.60 (0.0236) 0.64 (0.0252) 0.68 (0.0268) 0.72 (0.0283) 0.76 (0.0299) 0.80 (0.0315) 0.84 (0.0331) 0.88 (0.0346) 0.92 (0.0362) 0.96 (0.0378) 1.44 (0.0567) Part number* 31439-31X00 31439-31X01 31439-31X02 31439-31X03 31439-31X04 31439-31X05 31439-31X06 31439-31X07 31439-31X08 31439-31X09 31439-31X10 31439-31X11 31439-31X12 31439-31X13 31439-31X14 31439-31X15 31439-31X16 31439-31X17 31439-31X18
NCAT0189S08
AT-394

Final Drive (Contd)
TABLE FOR SELECTING DIFFERENTIAL SIDE BEARING ADJUSTING SHIMS (FOR RE4F03B)
Dial indicator deflection 0.31 - 0.35 (0.0122 - 0.0138) 0.35 - 0.39 (0.0138 - 0.0154) 0.39 - 0.43 (0.0154 - 0.0169) 0.43 - 0.47 (0.0169 - 0.0185) 0.47 - 0.51 (0.0185 - 0.0201) 0.51 - 0.55 (0.0201 - 0.0217) 0.55 - 0.59 (0.0217 - 0.0232) 0.59 - 0.63 (0.0232 - 0.0248) 0.63 - 0.67 (0.0248 - 0.0264) 0.67 - 0.71 (0.0264 - 0.0280) 0.71 - 0.75 (0.0280 - 0.0295) 0.75 - 0.79 (0.0295 - 0.0311) 0.79 - 0.83 (0.0311 - 0.0327) 0.83 - 0.87 (0.0327 - 0.0343) 0.87 - 0.91 (0.0343 - 0.0358) 0.91 - 0.95 (0.0358 - 0.0374) 0.95 - 0.99 (0.0374 - 0.0390) 0.99 - 1.03 (0.0390 - 0.0406) 1.03 - 1.07 (0.0406 - 0.0421) 1.07 - 1.11 (0.0421 - 0.0437) 1.11 - 1.15 (0.0437 - 0.0453) 1.15 - 1.19 (0.0453 - 0.0469) 1.19 - 1.23 (0.0469 - 0.0484) 1.23 - 1.27 (0.0484 - 0.0500) 1.27 - 1.31 (0.0500 - 0.0516) 1.31 - 1.35 (0.0516 - 0.0531) 1.35 - 1.39 (0.0531 - 0.0547) 1.39 - 1.43 (0.0547 - 0.0563) 1.43 - 1.47 (0.0563 - 0.0579) 1.47 - 1.51 (0.0579 - 0.0594) 1.51 - 1.55 (0.0594 - 0.0610) 1.55 - 1.59 (0.0610 - 0.0626) 1.59 - 1.63 (0.0626 - 0.0642) 1.63 - 1.67 (0.0642 - 0.0657) 1.67 - 1.71 (0.0657 - 0.0673) 1.71 - 1.75 (0.0673 - 0.0689) 1.75 - 1.79 (0.0689 - 0.0705) 1.79 - 1.83 (0.0705 - 0.0720) 1.83 - 1.87 (0.0720 - 0.0736) 1.87 - 1.91 (0.0736 - 0.0752) 1.91 - 1.95 (0.0752 - 0.0768) Suitable shim(s) 0.40 (0.0157) 0.44 (0.0173) 0.48 (0.0189) 0.52 (0.0205) 0.56 (0.0220) 0.60 (0.0236) 0.64 (0.0252) 0.68 (0.0268) 0.72 (0.0283) 0.76 (0.0299) 0.80 (0.0315) 0.84 (0.0331) 0.88 (0.0346) 0.92 (0.0362) (0.0189) + 0.48 (0.0189) (0.0189) + 0.52 (0.0205) (0.0205) + 0.52 (0.0205) (0.0205) + 0.56 (0.0220) (0.0220) + 0.56 (0.0220) (0.0220) + 0.60 (0.0236) (0.0236) + 0.60 (0.0236) (0.0236) + 0.64 (0.0252) (0.0252) + 0.64 (0.0252) (0.0252) + 0.68 (0.0268) (0.0268) + 0.68 (0.0268) (0.0268) + 0.72 (0.0283) 1.44 (0.0567) (0.0283) + 0.76 (0.0299) (0.0299) + 0.76 (0.0299) (0.0299) + 0.80 (0.0315) (0.0315) + 0.80 (0.0315) (0.0315) + 0.84 (0.0331) (0.0331) + 0.84 (0.0331) (0.0331) + 0.88 (0.0346) (0.0346) + 0.88 (0.0346) (0.0346) + 0.92 (0.0362) (0.0362) + 0.92 (0.0362) (0.0362) + 0.96 (0.0378) (0.0378) + 0.96 (0.0378) (0.0205) + 1.44 (0.0567) (0.0220) + 1.44 (0.0567)
NCAT0189S06
Unit: mm (in)
0.48 0.48 0.52 0.52 0.56 0.56 0.60 0.60 0.64 0.64 0.68 0.68 0.72 0.76 0.76 0.80 0.80 0.84 0.84 0.88 0.88 0.92 0.92 0.96 0.52 0.56
AT-395

Final Drive (Contd)
TABLE FOR SELECTING DIFFERENTIAL SIDE BEARING ADJUSTING SHIMS (FOR RE4F03W)
Dial indicator deflection 0.19 - 0.23 (0.0075 - 0.0091) 0.23 - 0.27 (0.0091 - 0.0106) 0.27 - 0.31 (0.0106 - 0.0122) 0.31 - 0.35 (0.0122 - 0.0138) 0.35 - 0.39 (0.0138 - 0.0154) 0.39 - 0.43 (0.0154 - 0.0169) 0.43 - 0.47 (0.0169 - 0.0185) 0.47 - 0.51 (0.0185 - 0.0201) 0.51 - 0.55 (0.0201 - 0.0217) 0.55 - 0.59 (0.0217 - 0.0232) 0.59 - 0.63 (0.0232 - 0.0248) 0.63 - 0.67 (0.0248 - 0.0264) 0.67 - 0.71 (0.0264 - 0.0280) 0.71 - 0.75 (0.0280 - 0.0295) 0.75 - 0.79 (0.0295 - 0.0311) 0.79 - 0.83 (0.0311 - 0.0327) 0.83 - 0.87 (0.0327 - 0.0343) 0.87 - 0.91 (0.0343 - 0.0358) 0.91 - 0.95 (0.0358 - 0.0374) 0.95 - 0.99 (0.0374 - 0.0390) 0.99 - 1.03 (0.0390 - 0.0406) 1.03 - 1.07 (0.0406 - 0.0421) 1.07 - 1.11 (0.0421 - 0.0437) 1.11 - 1.15 (0.0437 - 0.0453) 1.15 - 1.19 (0.0453 - 0.0469) 1.19 - 1.23 (0.0469 - 0.0484) 1.23 - 1.27 (0.0484 - 0.0500) 1.27 - 1.31 (0.0500 - 0.0516) 1.31 - 1.35 (0.0516 - 0.0531) 1.35 - 1.39 (0.0531 - 0.0547) 1.39 - 1.43 (0.0547 - 0.0563) 1.43 - 1.47 (0.0563 - 0.0579) 1.47 - 1.51 (0.0579 - 0.0594) 1.51 - 1.55 (0.0594 - 0.0610) 1.55 - 1.59 (0.0610 - 0.0626) 1.59 - 1.63 (0.0626 - 0.0642) 1.63 - 1.67 (0.0642 - 0.0657) 1.67 - 1.71 (0.0657 - 0.0673) 1.71 - 1.75 (0.0673 - 0.0689) 1.75 - 1.79 (0.0689 - 0.0705) 1.79 - 1.83 (0.0705 - 0.0720) 1.83 - 1.87 (0.0720 - 0.0736) 1.87 - 1.91 (0.0736 - 0.0752) 1.91 - 1.95 (0.0752 - 0.0768) Suitable shim(s) 0.28 (0.0110) 0.32 (0.0126) 0.36 (0.0142) 0.40 (0.0157) 0.44 (0.0173) 0.48 (0.0189) 0.52 (0.0205) 0.56 (0.0220) 0.60 (0.0236) 0.64 (0.0252) 0.68 (0.0268) 0.72 (0.0283) 0.76 (0.0299) 0.80 (0.0315) 0.84 (0.0331) 0.88 (0.0346) 0.92 (0.0362) (0.0189) + 0.48 (0.0189) (0.0189) + 0.52 (0.0205) (0.0205) + 0.52 (0.0205) (0.0205) + 0.56 (0.0220) (0.0220) + 0.56 (0.0220) (0.0220) + 0.60 (0.0236) (0.0236) + 0.60 (0.0236) (0.0236) + 0.64 (0.0252) (0.0252) + 0.64 (0.0252) (0.0252) + 0.68 (0.0268) (0.0268) + 0.68 (0.0268) (0.0268) + 0.72 (0.0283) 1.44 (0.0567) (0.0283) + 0.76 (0.0299) (0.0299) + 0.76 (0.0299) (0.0299) + 0.80 (0.0315) (0.0315) + 0.80 (0.0315) (0.0315) + 0.84 (0.0331) (0.0331) + 0.84 (0.0331) (0.0331) + 0.88 (0.0346) (0.0346) + 0.88 (0.0346) (0.0346) + 0.92 (0.0362) (0.0362) + 0.92 (0.0362) (0.0362) + 0.96 (0.0378) (0.0378) + 0.96 (0.0378) (0.0205) + 1.44 (0.0567) (0.0220) + 1.44 (0.0567)
NCAT0189S09
Unit: mm (in)
0.48 0.48 0.52 0.52 0.56 0.56 0.60 0.60 0.64 0.64 0.68 0.68 0.72 0.76 0.76 0.80 0.80 0.84 0.84 0.88 0.88 0.92 0.92 0.96 0.52 0.56
Reduction Pinion Gear

BEARING PRELOAD
Reduction pinion gear bearing preload 0.05 mm (0.0020 in)
TURNING TORQUE
Turning torque of reduction pinion gear 0.1 - 0.69 Nm (1.1 - 7.0 kg-cm, 0.95 - 6.08 in-lb)
NCAT0190S02
AT-396

Reduction Pinion Gear (Contd)
REDUCTION PINION GEAR BEARING ADJUSTING SHIMS

Thickness mm (in) 1.74 (0.0685) 1.78 (0.0701) 1.82 (0.0717) 1.86 (0.0732) 1.90 (0.0748) 1.92 (0.0756) 1.94 (0.0764) 1.96 (0.0772) 1.98 (0.0780) 2.00 (0.0787) 2.02 (0.0795) 2.04 (0.0803) 2.06 (0.0811) 2.08 (0.0819) 2.10 (0.0827) 2.12 (0.0835) 2.14 (0.0843) 2.16 (0.0850) 2.18 (0.0858) 2.20 (0.0866) 2.22 (0.0874) 2.24 (0.0882) 2.26 (0.0890) 2.28 (0.0898) 2.30 (0.0906) 2.34 (0.0921) 2.38 (0.0937) 2.42 (0.0953) 2.46 (0.0969) 2.50 (0.0984) 2.54 (0.1000) 2.58 (0.1016) 2.62 (0.1031) 2.66 (0.1047) Part number* 31438-31X16 31438-31X17 31438-31X18 31438-31X19 31438-31X20 31439-31X60 31438-31X21 31439-31X61 31438-31X22 31439-31X62 31438-31X23 31439-31X63 31438-31X24 31439-31X64 31438-31X60 31439-31X65 31438-31X61 31439-31X66 31438-31X62 31439-31X67 31438-31X63 31439-31X68 31438-31X64 31439-31X69 31438-31X65 31438-31X66 31438-31X67 31438-31X68 31438-31X69 31438-31X70 31438-31X71 31438-31X72 31438-31X73 31438-31X74
NCAT0190S03
AT-397

Reduction Pinion Gear (Contd)
TABLE FOR SELECTING REDUCTION PINION GEAR BEARING ADJUSTING SHIM

Dimension T 1.77 - 1.81 (0.0697 - 0.0713) 1.81 - 1.85 (0.0713 - 0.0728) 1.85 - 1.89 (0.0728 - 0.0744) 1.89 - 1.93 (0.0744 - 0.0760) 1.93 - 1.96 (0.0760 - 0.0772) 1.96 - 1.98 (0.0772 - 0.0780) 1.98 - 2.00 (0.0780 - 0.0787) 2.00 - 2.02 (0.0787 - 0.0795) 2.02 - 2.04 (0.0795 - 0.0803) 2.04 - 2.06 (0.0803 - 0.0811) 2.06 - 2.08 (0.0811 - 0.0819) 2.08 - 2.10 (0.0819 - 0.0827) 2.10 - 2.12 (0.0827 - 0.0835) 2.12 - 2.14 (0.0835 - 0.0843) 2.14 - 2.16 (0.0843 - 0.0850) 2.16 - 2.18 (0.0850 - 0.0858) 2.18 - 2.20 (0.0858 - 0.0866) 2.20 - 2.22 (0.0866 - 0.0874) 2.22 - 2.24 (0.0874 - 0.0888) 2.24 - 2.26 (0.0882 - 0.0890) 2.26 - 2.28 (0.0890 - 0.0898) 2.28 - 2.30 (0.0898 - 0.0906) 2.30 - 2.32 (0.0906 - 0.0913) 2.32 - 2.34 (0.0913 - 0.0921) 2.34 - 2.37 (0.0921 - 0.0933) 2.37 - 2.41 (0.0933 - 0.0949) 2.41 - 2.45 (0.0949 - 0.0965) 2.45 - 2.49 (0.0965 - 0.0980) 2.49 - 2.53 (0.0980 - 0.0996) 2.53 - 2.57 (0.0996 - 0.1012) 2.57 - 2.61 (0.1012 - 0.1028) 2.61 - 2.65 (0.1028 - 0.1043) 2.65 - 2.69 (0.1043 - 0.1059) 2.69 - 2.73 (0.1059 - 0.1075) Suitable shim(s) 1.74 (0.0685) 1.78 (0.0701) 1.82 (0.0717) 1.86 (0.0732) 1.90 (0.0748) 1.92 (0.0756) 1.94 (0.0764) 1.96 (0.0772) 1.98 (0.0780) 2.00 (0.0787) 2.02 (0.0795) 2.04 (0.0803) 2.06 (0.0811) 2.08 (0.0819) 2.10 (0.0827) 2.12 (0.0835) 2.14 (0.0843) 2.16 (0.0850) 2.18 (0.0858) 2.20 (0.0866) 2.22 (0.0874) 2.24 (0.0882) 2.26 (0.0890) 2.28 (0.0898) 2.30 (0.0906) 2.34 (0.0921) 2.38 (0.0937) 2.42 (0.0953) 2.46 (0.0969) 2.50 (0.0984) 2.54 (0.1000) 2.58 (0.1016) 2.62 (0.1031) 2.66 (0.1047)
NCAT0190S04
Unit: mm (in)
Output Shaft
SEAL RING CLEARANCE
Standard Output shaft seal ring clearance Allowable limit 0.25 (0.0098) 0.10 - 0.25 (0.0039 - 0.0098)
Unit: mm (in)
END PLAY
Output shaft end play 0 - 0.5 mm (0 - 0.020 in)
NCAT0191S02
OUTPUT SHAFT END PLAY ADJUSTING SHIMS

Thickness mm (in) 0.56 (0.0220) 0.96 (0.0378) 1.36 (0.0535) Part number* 31438-31X46 31438-31X47 31438-31X48
NCAT0191S03
Bearing Retainer
SEAL RING CLEARANCE
Standard Bearing retainer seal ring clearance Allowable limit 0.25 (0.0098) 0.10 - 0.25 (0.0039 - 0.0098)
Unit: mm (in)
AT-398

Total End Play
Total End Play

Total end play T3 0.25 - 0.55 mm (0.0098 - 0.0217 in)
NCAT0193
GI
NCAT0193S01
BEARING RACE FOR ADJUSTING TOTAL END PLAY

Thickness mm (in) 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 (0.024) (0.031) (0.039) (0.047) (0.055) (0.063) (0.071) (0.079) Part number* 31435-31X01 31435-31X02 31435-31X03 31435-31X04 31435-31X05 31435-31X06 31435-31X07 31435-31X08
MA EM LC EC
Reverse Clutch End Play

Reverse clutch end play T4 0.65 - 1.00 mm (0.0256 - 0.0394 in)
NCAT0194
FE CL
THRUST WASHERS FOR ADJUSTING REVERSE CLUTCH END PLAY

Thickness mm (in) 0.65 0.80 0.95 1.10 1.25 1.40 (0.0256) (0.0315) (0.0374) (0.0433) (0.0492) (0.0551) Part number* 31508-31X10 31508-31X11 31508-31X12 31508-31X13 31508-31X14 31508-31X15
NCAT0194S01
MT
AX
Accumulator
O-RING
Accumulator Servo release accumulator N-D accumulator Diameter (Small) 26.9 (1.059) 34.6 (1.362) Part number* 31526-41X03 31526-31X08 Diameter (Large) 44.2 (1.740) 39.4 (1.551)
SU BR ST RS
Unit: mm (in)
Part number* 31526-41X02 31672-21X00
RETURN SPRING
Accumulator Servo release accumulator spring N-D accumulator spring Free length 52.5 (2.067) 45.0 (1.772) Outer diameter 20.1 (0.791) 27.6 (1.087)
NCAT0195S02
Unit: mm (in)
Part number* 31605-80X00 31605-33X01
BT HA SC
NCAT0196
Band Servo
RETURN SPRING
Return spring 2nd servo return spring OD servo return spring Free length 32.5 (1.280) 38.52 (1.5165) Outer diameter 25.9 (1.020) 22.0 (0.866) Part number* 31605-31X20 31605-31X21
NCAT0196S01
Unit: mm (in)
EL IDX
AT-399

Removal and Installation
Removal and Installation

Distance between end of converter housing and torque converter 15.9 (0.626) or more
NCAT0197
Unit: mm (in)
Shift Solenoid Valves

Gear 1st 2nd 3rd 4th Solenoid A ON OFF OFF ON Solenoid B ON ON OFF OFF
NCAT0223
Solenoid Valves
Solenoid valve Shift solenoid A Shift solenoid B Ovr. clutch sol. Line pres. sol. T/conv. clutch sol. Resistance (Approx.) 20 - 30 5 - 20 20 - 30 2.5 - 5 5 - 20 Terminal number 2 1 3 4 5
NCAT0224
A/T Fluid Temperature Sensor

Monitor item Condition Cold [20C (68F)] " Hot [80C (176F)] 1.5V " 0.5V Specification (Approximately) 2.5 k " 0.3 k
NCAT0225
Revolution Sensor
150 Hz/20 km/h (12 MPH)
NCAT0226
Dropping Resistor
Resistance 10 - 15
NCAT0227
AT-400

At - Automatic Transaxel

Uploaded by

Copyright:

Available Formats

At - Automatic Transaxel

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

At - Automatic Transaxel

Uploaded by

Copyright:

Available Formats

AUTOMATIC TRANSAXLE SECTION

TROUBLE DIAGNOSIS INDEX

Alphabetical & P No. Index for DTC

TROUBLE DIAGNOSIS INDEX

P NO. INDEX FOR DTC

Precautions for On Board Diagnostic (OBD) System of A/T and Engine

Service Notice or Precautions

TORQUE CONVERTER SERVICE

ATF COOLER SERVICE

Wiring Diagrams and Trouble Diagnosis

Special Service Tools

Measuring line pressure and governor pressure

KV38107700 (J39027) Preload adapter

KV31103200 (J34285-A and J3428587) Clutch spring compressor

ST23540000 (J25689-A) Pin punch

ST25710000 ( Pin punch

ST27180001 (J25726-A) Puller

ST30031000 (J22912-1) Puller

ST35272000 (J26092) Drift

ST35271000 (J26091) Drift

Installing idler gear a: 72 mm (2.83 in) dia. b: 63 mm (2.48 in) dia.

ST33400001 (J26082) Drift

Commercial Service Tools

A/T Electrical Parts Location

Cross-sectional View RE4F03B

Cross-sectional View RE4F03W

Hydraulic Control Circuit

9. 10. 11. 12. 13. 14. 15. 16.

17. 18. 19. 20. 21. 22. 23. 24.

FUNCTION OF CLUTCH AND BRAKE

CLUTCH AND BAND CHART

POWER TRANSMISSION N and P Positions

D2, 22 and 12 Positions

INPUT/OUTPUT SIGNAL OF TCM

Back-up Control (Engine brake)

During Shift Change

At Low Fluid Temperature

Control of Shift Solenoid Valves A and B

Control of Shift Valves A and B

Conditions for Lock-up Operation

Torque Converter Clutch Solenoid Valve Control

Torque Converter Clutch Control Valve OperationNCAT0015S0303

OVERRUN CLUTCH CONTROL (ENGINE BRAKE CONTROL)

Overrun Clutch Operating Conditions

Overrun Clutch Solenoid Valve Control

Overrun Clutch Control Valve Operation

Overrun clutch control valve

1st reducing valve Overrun clutch reducing valve

ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION

OBD-II Function for A/T System

One or Two Trip Detection Logic of OBD-II

TWO TRIP DETECTION LOGIC

OBD-II Diagnostic Trouble Code (DTC)

ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION

If the DTC is being detected currently, the time data will be 0.

Freeze Frame Data and 1st Trip Freeze Frame Data

ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION

HOW TO ERASE DTC

HOW TO ERASE DTC (WITH CONSULT-II)

ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION