MP, FP & BP

Melting Point
1. The temperature at which a solid becomes a liquid at standard atmospheric pressure.

2. The temperature at which a solid and its liquid are in equilibrium, at any fixed pressure.
The temperature at which a solid changes to a liquid. For pure substances, the melting or fusion
process occurs at a single temperature, the temperature rise with addition of heat being arrested
until melting is complete.
Melting points reported in the literature, unless specifically stated otherwise, have been measured
under an applied pressure of 1 atm (105 pascals), usually 1 atm of air. (The solubility of air in the
liquid is a complicating factor in precision measurements.) Upon melting, all substances absorb
heat, and most substances expand; consequently an increase in pressure normally raises the
melting point. A few substances, of which water is the most notable example, contract upon
melting; thus, the application of pressure to ice at 32°F (0°C) causes it to melt. Large changes in
pressure are required to produce significant shifts in the melting point.
For solutions of two or more components, the melting process normally occurs over a range of
temperatures, and a distinction is made between the melting point, the temperature at which the
first trace of liquid appears, and the freezing point, the higher temperature at which the last trace
of solid disappears, or equivalently, if one is cooling rather than heating, the temperature at
which the first trace of solid appears. See also Phase equilibrium; Solution; Sublimation; Triple
point.
Melting Point, Freezing Point, Boiling Point
Melting Point and Freezing Point
Pure, crystalline solids have a characteristic melting point, the temperature at which the solid
melts to become a liquid. The transition between the solid and the liquid is so sharp for small
samples of a pure substance that melting points can be measured to 0.1oC. The melting point of
solid oxygen, for example, is -218.4oC.
Liquids have a characteristic temperature at which they turn into solids, known as their freezing
point. In theory, the melting point of a solid should be the same as the freezing point of the
liquid. In practice, small differences between these quantities can be observed.
It is difficult, if not impossible, to heat a solid above its melting point because the heat that enters
the solid at its melting point is used to convert the solid into a liquid. It is possible, however, to
cool some liquids to temperatures below their freezing points without forming a solid. When this
is done, the liquid is said to be supercooled.
An example of a supercooled liquid can be made by heating solid sodium acetate trihydrate
(NaCH3CO2 3 H2O). When this solid melts, the sodium acetate dissolves in the water that was
trapped in the crystal to form a solution. When the solution cools to room temperature, it should
1
solidify. But it often doesn't. If a small crystal of sodium acetate trihydrate is added to the liquid,
however, the contents of the flask solidify within seconds.
A liquid can become supercooled because the particles in a solid are packed in a regular structure
that is characteristic of that particular substance. Some of these solids form very easily; others do
not. Some need a particle of dust, or a seed crystal, to act as a site on which the crystal can grow.
In order to form crystals of sodium acetate trihydrate, Na+ ions, CH3CO2- ions, and water
molecules must come together in the proper orientation. It is difficult for these particles to
organize themselves, but a seed crystal can provide the framework on which the proper
arrangement of ions and water molecules can grow.
Because it is difficult to heat solids to temperatures above their melting points, and because pure
solids tend to melt over a very small temperature range, melting points are often used to help
identify compounds. We can distinguish between the three sugars known as glucose (MP =
150oC), fructose (MP = 103-105oC), and sucrose (MP = 185-186oC), for example, by
determining the melting point of a small sample.
Measurements of the melting point of a solid can also provide information about the purity of the
substance. Pure, crystalline solids melt over a very narrow range of temperatures, whereas
mixtures melt over a broad temperature range. Mixtures also tend to melt at temperatures below
the melting points of the pure solids.
Boiling Point
When a liquid is heated, it eventually reaches a temperature at which the vapor pressure is large
enough that bubbles form inside the body of the liquid. This temperature is called the boiling
point. Once the liquid starts to boil, the temperature remains constant until all of the liquid has
been converted to a gas.
The normal boiling point of water is 100oC. But if you try to cook an egg in boiling water while
camping in the Rocky Mountains at an elevation of 10,000 feet, you will find that it takes longer
for the egg to cook because water boils at only 90oC at this elevation.
In theory, you shouldn't be able to heat a liquid to temperatures above its normal boiling point.
Before microwave ovens became popular, however, pressure cookers were used to decrease the
amount of time it took to cook food. In a typical pressure cooker, water can remain a liquid at
temperatures as high as 120oC, and food cooks in as little as one-third the normal time.
To explain why water boils at 90oC in the mountains and 120oC in a pressure cooker, even
though the normal boiling point of water is 100oC, we have to understand why a liquid boils. By
definition, a liquid boils when the vapor pressure of the gas escaping from the liquid is equal to
the pressure exerted on the liquid by its surroundings, as shown in the figure below.
2
Liquids boil when their vapor pressure is equal to the pressure exerted on the
liquid by its surroundings.
The normal boiling point of water is 100oC because this is the temperature at which the vapor
pressure of water is 760 mmHg, or 1 atm. Under normal conditions, when the pressure of the
atmosphere is approximately 760 mmHg, water boils at 100oC. At 10,000 feet above sea level,
the pressure of the atmosphere is only 526 mmHg. At these elevations, water boils when its
vapor pressure is 526 mmHg, which occurs at a temperature of 90oC.
Pressure cookers are equipped with a valve that lets gas escape when the pressure inside the pot
exceeds some fixed value. This valve is often set at 15 psi, which means that the water vapor
inside the pot must reach a pressure of 2 atm before it can escape. Because water doesn't reach a
vapor pressure of 2 atm until the temperature is 120oC, it boils in this container at 120oC.
Liquids often boil in an uneven fashion, or bump. They tend to bump when there aren't any
scratches on the walls of the container where bubbles can form. Bumping is easily prevented by
adding a few boiling chips to the liquid, which provide a rough surface upon which bubbles can
form. When boiling chips are used, essentially all of the bubbles that rise through the solution
form on the surface of these chips.

MP, FP & BP

Uploaded by

Copyright:

Available Formats

MP, FP & BP

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

MP, FP & BP

Uploaded by

Copyright:

Available Formats

What factors affect the melting and boiling points of substances?

What is supercooling and how does it relate to crystallization?

Melting Point

1. The temperature at which a solid becomes a liquid at standard atmospheric pressure.

Melting Point, Freezing Point, Boiling Point

Melting Point and Freezing Point

You might also like