Table of Contents

COMPONENT LOCATION DIAGRAM..................................... A

INDEX................................................................................................. 1

CHAPTER 1 INTRODUCTION.................................................. 2

1-1 SYSTEM FEATURES ............................................................. 3

1-2 SOFTWARE POWER OFF CONTROL.................................. 4

1-3 LDCM ( LANDesk Client Manager, option)............................... 5

1-4 CHECK LIST OF THE PACKAGING ..................................... 6

CHAPTER 2 INSTALLATION................................................... 7

2-1 INSTALLATION PROCEDURES ......................................... 7

2-2 CPU INSTALLATION............................................................. 8

2-3 SYSTEM MEMORY INSTALLATION.................................... 10

2-4 CONNECTORS DESCRIPTION............................................. 12

2-5 IDE DRIVER INSTALLATION............................................... 17

CHAPTER 3 Award BIOS SETUP ............................................ 18

3-1 UPDATE BIOS PROCEDURES .............................................. 19

3-1-1 UPDATE Award SYSTEM BIOS (FLASH EPROM)
3-1-2 UPDATE PENTIUM PRO BIOS API

3-2 Award SYSTEM BIOS CONFIGURATION SETUP ................ 21

APPENDIX A ....................................................................................46

APPENDIX B How to install Pentium II ?.................................. ..B

1
CHAPTER 1 INTRODUCTION

This manual describes how to configure the ATC-6120 mainboard for different
environments. It's an overview of the layout and features of the mainboard, and also
provides information for you to change the configuration or system environment.

This manual is divided into Three parts :

PART ONE includes page A and two chapters as following:

Page A contains layout diagram of the mainboard. Please refer to it
when you configure the system.

Chapter 1 is an overview of the mainboard features and packing contents.

Chapter 2 describes how to upgrade and to change hardware configurations
such as memory size, CPU type, and lists of jumper settings and
connectors.

PART TWO includes chapter 3 which contains Award BIOS description..

Chapter 3 is the user's guide of the Award BIOS setup utility and Flash ROM BIOS.
The menu shown in this chapter are the default settings.

PART THREE includes APPENDIX A and APPENDIX B,

APPENDIX A is a technical support form

APPENDIX B is the user’s guide of how to setup Pentium II

Your system dealer will set up the mainboard according to your demand of the
computer. It means that the current settings of your mainboard may not be the same as the
defaults shown in this user's manual. If you need to change your configuration, please ask
your dealer first. Be sure this will not void your system warranty, or ask your dealer to do it
for you.

REMARK
Intel® is a registered trademark of Intel Corporation.
All other brands and product names are trademarks registered trademarks of their respective companies.

2
1-1 SYSTEM FEATURES

: INTEL Pentium II CPU operating at 233MHz and 300MHz by using Single Edge
Contact (S.E.C.) cartridge (or named Slot 1).
: INTEL 82440LX PCIset.
: Pentium II CPU with MMXTM Technology, and 512 or 256KB L2 Cache.
Cacheable 512MB.
: Using three 168-pin DIMM sockets, provides three banks of 64-bit wide path up to
384MB SDRAM or 768MB EDO DRAM (with parity chip ECC support).
: Built-in Switching Voltage Regulator.
: Built-in LM78, LM75 supports INTEL LDCM.(option)
: Supports auto-detect CPU core voltage range 1.8V to 3.5V.
: Supports one AGP slot, four PCI revision 2.1 interface compliant and three 16-bit
ISA slots.
: Dual Master IDE connectors support Ultra DMA/33, up to four devices in two
channels for connecting of high capacity hard drive, CD-ROM, tape backup etc..
: Supports the USB (Universal Serial Bus) header.
: PS/2 keyboard connector and PS/2 mouse connector.
: Winbond 83977 high-speed Ultra Multi-I/O chipset.
: Supports Infrared transfer (IrDA TX/RX) connection.
: One FDC port supports two devices up to 2.88MB
: Two 16550A fast UARTs compatible serial ports
: One EPP/ECP mode parallel port
: Hardware Dimension is 210mm x 305mm (8.26" x 12.00").

3
1-2 SOFTWARE POWER OFF CONTROL
The mainboard design supports Software Power Off Control feature through the
SMM code in the BIOS under Windows 95, Windows 3.1x, and MS-DOS operation
system environment. This is Intel ATX form factor feature and you should use ATX
power supply.

First, you should connect the power switch cable (provided by the ATX case
supplier) to the connector “PS-ON” (next to SW1) on the mainboard. In the BIOS
screen of ‘POWER MANAGEMENT SETUP’, choose “User Defined” (or “Min.
Power Saving” or “Max. Power Saving”) in ‘Power Manager’ and choose “Yes” in
‘PM Control by APM’.

In Windows 95, if you would like to power off the system, you just choose
“shutdown the computer ?” in the “Shut Down Windows“ from Windows 95, then the
system power will be off directly, and become the stand-by status. You will find the
power LED light blinking. If you would like to restart the system, just press the power
switch button, and the system will be powered on.

In Windows 3.1x or MS-DOS, you should copy the program of “down.com”

(you can find it in the diskette of the IDE driver) into the hard drive. When you would
like to power off the system, just run this “down.com”, then the system will be
shutdown and stay in standby status.

Note : If you will leave your system for several days, we suggest you use hardware
power off to shutdown your system.

4
1-3 LDCM LANDesk Client Manager (option)
ATC-6120 built-in LM 78 / LM 75 support Intel LDCM. LDCM can satisfy users
who want manageable systems that can interact automatically with the user. Client
manager is the answer, enabling both administrators and clients to manage systems.
The features of LDCM are as following :
Review system inventory
Client Manager enables you to view hundreds of inventoried items. Some of these
items are software related, while many others are hardware related.

View DMI-compliant component information

Client manager enables you to view component information that is compliant with the
Desktop Manager Interface DMI . This means you can manage third-party
DMI-compliant components not included with Client manager.

Back up and restore system configuration files.

Client Manager enables you back up and restore system configuration files. Whenever
you plan on changing the system configuration , you can make a backup set. If the
system no longer works correctly, after you the change the system configuration ,
you can simply restore the system configuration with the backup set.

Troubleshoot
Since Client manager enables you to view the system inventory, you can easily
troubleshoot system problems.

Receive notifications for system events

Client manager enables you to receive notification of certain system events. For
example, if the system is running low on virtual memory, you are notified of the
potential problem.

Transfer files to and from client workstations

As an administrator, you have the ability to transfer files to and from client workstation.
This is helpful, for example, when you need to update a client workstation driver.

Remotely reboot client workstations

Administrator also have the ability to remotely reboot a workstation . This is helpful
when you want system configuration changes to take effect.

5
1-3 CHECK LIST OF THE PACKAGING
The mainboard comes securely packed in a durable box and shipping carton. If
any of the following items are missing or damaged, please contact your supplier.

Each mainboard contains:

Q'TY Description
1 Mainboard : ATC-6120.
1 Retention module (for Pentium II installation)
1 Diskette : Enhanced IDE driver (3.5")
Award system BIOS
Update Utility
1 Cable : Enhanced IDE connector.
1 Cable : F.D.D. connector.
1 Manual : User`s manual.

NOTE : Leave the mainboard in its original packaging until you are ready to install it.

6
CHAPTER 2 INSTALLATION

2-1 INSTALLATION PROCEDURE

Before installing the computer, please prepare all components such as CPU, DRAM;
peripherals such as hard drive, keyboard, CD-ROM; and accessories such as cables.
Then, install the system as following:

1. Plug CPU/ heat sink (refer to Pentium II installation guide), and DRAM modules in
the mainboard.
2. Set DIP switch based on your configuration.
3. Plug add-on cards in PCI/ISA slots.
4. Connect cables to peripherals, power supply.
5. Make sure all components and devices are well connected, turn on the power and
setup System BIOS based on your configuration.
6. Install peripherals, add-on card drivers and test them.
7. If all of above procedures are success, turn-off the power then plug all of them into
your computer case.

7
2-2 CPU INSTALLATION
ATC-6120 supports INTEL Pentium II CPU cartridge.

2-2-1 CPU TYPE SELECTION

INTERNAL CPU CLOCK SW1 Ext.x Frq.

233MHz ON 66x3.5

OFF
1 2 3 4

266MHz ON 66x4.0

OFF
1 2 3 4

300MHz ON 66x4.5

OFF
1 2 3 4

SW1 Slot 1
1234 ON DIP

1 2 3 4

DIP switch, ( ex. : ON,ON,ON,OFF)

O N : switch to the ‘ON’
position.
OFF : switch to the ‘OFF’ position.

8
2-2-2 CPU VOLTAGE SETTING

The ATC-6120 mainboard has built-in VID (Voltage IDentify) function to

auto-detect various CPU voltages, you do not need to adjust the CPU voltage setting
when you install the Pentium II CPU card on this mainboard.

9
2-3 SYSTEM MEMORY INSTALLATION
The ATC-6120 provides three 168-pin DIMM sockets for system memory
expansion from 8MB to 384MB. These three DIMMs are arranged to three banks,
please refer to page A. Each bank provides 64-bit wide data path.

Samples of System Memory Combinations Options

BANK0 BANK1 BANK2 Total Memory

DIMM 1 DIMM 2 DIMM 3 DIMM 1-3
8MBx1 - - 8MB
- 8MBx1 - 8MB

- - 8MBx1 8MB

8MBx1 8MBx1 16MB

- 8MBx1 8MBx1 16MB

8MBx1 - 8MBx1 16MB

16MBx1 - - 16MB

- 16MBx1 - 16MB

- - 16MBx1 16MB

8MBx1 8MBx1 8MBx1 24MB

8MBx1 16MBx1 - 32MB

16MBx1 16MBx1 32MB

16MBx1 - 16MBx1 32MB

32MBx1 - - 32MB

- 32MBx1 - 32MB

- - 32MBx1 32MB

8MBx1 16MBx2 16MBx1 40MB

- continue -

10
32MBx1 32MBx1 - 64MB

- 32MBx1 32MBx1 64MB

64MBx1 - - 64MB

- 64MBx1 64MBx1 128MB

: : : :

: : : :

128MBx1 128MBx1 128MBx1 384MB

11
2-4 CONNECTORS DESCRIPTION
The locations of following connectors are indicated in page A. When you plug a
cable into the following I/O connectors, you should have the pin 1 edge of the cable
align with the pin 1 end of the connector.

CONN1 : speaker, keyboard lock, reset, SMI,

turbo LED, and IDE LED connectors.

SPK : speaker
RST

SPK

Speaker
GND
SMI

GND
VCC
TB-LED IDE-LED

KEYLOCK

Power LED connector

PS ON

Power LED +
N/C
GND (power)
Keylock
GND

RST : Reset connector

Reset Signal
GND

SMI : SMI lead

GND
SMI Signal

TB-LED : Turbo LED indicator, LED on

when system runs higher speed
GND
+5V (next to CPU)

12
 IDE-LED : IDE devices indicator LED
connector. IDE-LED stays ON indicates
GND on-board IDE devices in operation. If
+5V plug wire into wrong connector, color
of
LED will be lighter and the IDE dvices
can
FAN : CPU cooling fan connector. Wire with
+12V voltage (most likely red wire) must be
plugged into pin2, and GROUND wires
(most likely black wires) must be plugged into
1 Sense
pin3. Please confirm the wire color
2 +12V re-presentation with your supplier.
3 GND CAUTION: Plug wire into wrong connector will
DAMAGE fan and mainboard.
FAN1 for Pentium II CPU Fan, FAN2 ATX case,
FAN3 for AGP card.

IR1 : Infrared module connector.

1 +5V
2 N/C
3 IRRX
4
GN
D

USB : USB connector; Universal Serial Bus; this

is used to connect USB devices. There are
1 +5V three connectors on board, user can choice
2 USB P1- two in the same time.
3 USB P1+
4 Ground

13
 PS/2 KB : 6-pin PS/2 style compatible keyboard
connector.

PS/2 mouse : PS/2 mouse connector, which is

used to connect an optional cable.
6 5
pin1 : data
4 pin2 : N/C
3 pin3 : GND
pin4 : VCC
2 1 pin5 : clock
pin6 : N/C

PW1 : ATX mode +3.3/5/12V power supply

connector.
1 3.3V 6 +5V 11 3.3V 16 GND
1 10
2 3.3V 7 GND 12 -12V 17 GND
3 GND 8 PWRGD 13 GND 18 -5V
11 20
4 +5V 9 5VSB 14* PS_ON 19 +5V
5 GND 10 +12V 15 GND 20 +5V
* PS_ON : Soft-Off power control

COM1/COM2 : these two connectors are

used to connect serial port cables.
1
6 2 pin signal name
7 3 1 NDCDA/B
8 4 2 NSINA/B
9 5 3 NSOUTA/B
4 NDTRA/B
5 GND
6 NDSRA/B
7 NRTSA/B
8 NCTSA/B
9 NRIA/B
A is COM1, B is COM2
14
 FDC1 : this connector is used to connect the floppy
drive through a cable.
34 33
pin signal pin signal
2 RWC- 20 STEP-
4 reserved 22 Write Data
6 FDEDIN 24 Write Gate
8 Index- 26 Track 00-
10 Motor EnableA- 28 Write Protect-
2 1
12 Drive Sele.B- 30 Read Data-
14 Drive Sele.A- 32 Side 1 Sele.-
16 Motor EnableB- 34 DisketteChange
18 DIR-
All of odd pins are ground

LPT : this connector is used to connect parallel

port cable.
25 13 pin signal pin signal
1 STROBE- 10 ACK-
2 Data Bit 0 11 BUSY
3 Data Bit 1 12 PE
4 Data Bit 2 13 SLCT
5 Data Bit 3 14 Auto Feed-
6 Data Bit 4 15 ERROR-
13 1
7 Data Bit 5 16 INIT-
8 Data Bit 6 17 SLCT IN-
9 Data Bit 7
pin18 -- pin25 are ground

LPT

Keyboard COM 1
conn. COM2

Dual USB

15
 IDE1/IDE2 : these two connectors are used to
connect IDE devices through IDE cables,
40 39 a total of 4 devices can be connected.

pin signal pin signal

1 Reset IDE 21 DDRQ0(1)
2 GND 22 GND
3 Host Data 7 23 I/O Write-
4 Host Data 8 24 GND
4 3 5 Host Data 6 25 I/O Read-
2 1 6 Host Data 9 26 GND
7 Host Data 5 27 IORDY
8 Host Data 10 28 N/C
9 Host Data 4 29 DDAK0- (1-)
10 Host Data 11 30 GND
11 Host Data 3 31 IRQ14*
12 Host Data 12 32 IOCS16-
13 Host Data 2 33 Addr 1
14 Host Data 13 34 N/C
15 Host Data 1 35 Addr 0
16 Host Data 14 36 Addr 2
17 Host Data 0 37 ChipSele.1P-
18 Host Data 15 38 ChipSele.3P-
19 GND 39 Activity
20 Key 40 GND
* IDE1 : pin31 is IRQ14;
IDE2 : pin31 is IRQ15 or MIRQ0

16
2-5 IDE DRIVER INSTALLATION
The IDE driver installation procedure is as following :

Setup for Windows 95 :

1. Starting Windows 95
2. Select “START”, “RUN”.
3. Install INF.EXE before you install IDE driver, please refer to
readme file.
4. Type “A:\WIN95\SETUP.EXE”.
5. Restart computer, then follow the instructions on your
screen to install new IDE driver we offer in the 3.5“ diskette
6. Exit Windows 95, turn power off; then turn power on.
After installation, the screen will show a yellow , please ignore it.
(The other platforms please refer to readme file.)

Make sure your HDD should follow ATA standard, and your CD-ROM should
follow ATAPI standard. When you plug-in the IDE devices, please plug your first and
second devices into IDE 1 port (Master then Slave), then plug third and forth devices
into IDE 2 port. If you have CD-ROM driver, please set it behind hard disk devices as
the last device. For example, if you have 2 HDDs and 1 CD-ROM, you should set
HDD1 and HDD2 in IDE1 Master and Slave, set CD-ROM in IDE 2 Master. Some of the
brands devices combination may not work under this sequence, you can try to re-arrange the devices
sequence, or contact your vendor.

Primary Primary Secondary Secondary

Master Slave Master Slave
ATA no ATAPI
ATA ATAPI disk & CD-ROM
ATA ATAPI use only one cable
CD-ROM and a tape
ATA ATAPI ATAPI
or two CD-ROMs

17
CHAPTER 3 Award BIOS SETUP

This chapter explains the system BIOS setup, and how to update to a new BIOS.
All BIOS screens shown in the following pages are default values, your system dealer
will set up these values according to your demand of the computer. Please refer to the
next page for the update procedure.

ATC-6120 uses Flash ROM to make the BIOS easily to be updated by the floppy
disk-based program. and to meet Microsoft Windows 95 plug & play feature. After the
BIOS is updated, you should clear the setup data stored in the CMOS.

JP2 Setting is for Update System CMOS

JP2 JP2 JP2

Normal 1-2
Clear 2-3

NOTE :
To clear CMOS you should Normal Clear CMOS
unplug the power cord, then CMOS
set 2-3 to clear, put it back to normal position and plug
the power cord again.

18
3-1 UPDATE BIOS PROCEDURES
If the BIOS needs to be updated, you can get a diskette with the updated BIOS
from your system supplier. The BIOS diskette includes :
“awdflash.exe” -- BIOS update utility program
“awdflash.doc”
“(update BIOS filename with version number).bin”

The update procedure is as following:

1. Boot the system to DOS mode in a normal manner.

2. Insert the updated diskette to drive A (or B).
3. Change working directory to floppy drive, A or B, which contains the update BIOS
diskette. -- Type “a:\” or “b:\”, “ENTER”.
4. Run the BIOS update utility -- Type “awdflash”, “ENTER”.
5. Type “(update BIOS file name with version number).bin”, ENTER.
6. If you do not want to save the old BIOS Type “N” when the screen displays the
message : " Do you want to save BIOS (Y/N) ?".
7. Type “Y“ when the screen shows the message : " Are you sure to program
(Y/N) ?".
8. Follow instructions displayed on the screen. DO NOT remove the update BIOS
diskette from the floppy drive nor turn the system power off until the BIOS update
is completed.
9. Turn the power off. Clear the data in CMOS according to the procedure described
in the previous page.
10. Turn the system power on and test that your system is working properly.

19
3-1-2 UPDATE PENTIUM II BIOS API

Intel also provides BIOS API(Applications Programming Interface) for Pentium II

processor-based mainboard user to update data block in BIOS quickly and easily.
(You can find this utility in the 3.5“ diskette in the package).

The BIOS code on the Pentium II processor-based mainboards contains data that is
specific to each silicon stepping of the processor. Integrators must ensure that this BIOS
stepping data matches the processor stepping used. When the BIOS does not contain
stepping data that matches the processor stepping, integrators must update the data in the
BIOS before shipping the system. Historically, Pentium II systems have been updated by
replacing the entire BIOS with a new revision of BIOS that contains the correct stepping
data.

Intel‘s BIOS update API allows just the stepping data within the BIOS to be updated
as needed. Mainboards that contain a BIOS with the Intel-defined BIOS update API can
be quickly and easily updated, if required, without obtaining a complete BIOS upgrade.
Using this utility, integrators can easily verify that the correct stepping data is present in all
Pentium II processor-based mainboards. However, if the stepping data requires updating,
the mainboard BIOS must contain the Intel-defined BIOS update API, otherwise a
complete BIOS upgrade is required from the mainboard vendor.

Yould should set your diskette to “write protect, then type

A:\>cd api; A:\api>checkup3

The main menu should now be displayed, showing the following four options :
1) Check and load update
2) Specify stepping data file [current : pep.pdb]
3) Help
4) Quit without loading update

Select 1 to know the stepping filename, select 2 to load right patch code, then
select 1 to update proper patch code. Now, the screen will show the message “please
remove floppy diskette from floppy disk drive”. Then cold boot (mechanical power off)
system to continue. For more information, please refer to “CHECKUP.HLP“ file.

20
3-2 AWARD SYSTEM BIOS
CONFIGURATION SETUP
The following pages explain how to set up the system configuration (CMOS)
under the AWARD BIOS. The SETUP program is stored in the Read-Only-Memory
(ROM) on the mainboard. To do the SETUP procedure, press the <Del> key when the
system is booting up. The following main menu will appear. Please select "
STANDARD CMOS SETUP" to enter the next screen.

ROM PCI/ISA BIOS (2A69JA29)

CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP INTEGRATED PERIPHERALS
BIOS FEATURES SETUP SUPERVISOR PASSWORD
CHIPSET FEATURES SETUP USER PASSWORD
POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION
PNP/PCI CONFIGURATION SAVE & EXIT SETUP
LOAD BIOS DEFAULTS EXIT WITHOUT SAVING
LOAD SETUP DEFAULTS
ESC: Quit áâàß:Select Item
F10: Save & Exit Setup (Shift) F2 : Change Color
Time, Date, Hard Disk Type .....

The section on the bottom of the main menu explains how to control this screen. The
other section displays the items highlighted in the list.

21
This screen records some basic hardware information, and sets the system clock and error handling.
These records can be lost or corrupted if the on-board battery has failed or is weak.

ROM PCI/ISA BIOS (2A69JA29)

CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP INTEGRATED PERIPHERALS
BIOS FEATURES SETUP SUPERVISOR PASSWORD
CHIPSET FEATURES SETUP USER PASSWORD
POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION
PNP/PCI CONFIGURATION SAVE & EXIT SETUP
LOAD BIOS DEFAULTS EXIT WITHOUT SAVING
LOAD SETUP DEFAULTS
ESC: Quit áâàß:Select Item
F10: Save & Exit Setup (Shift) F2 : Change Color
Time, Date, Hard Disk Type .....

ROM PCI/ISA BIOS (2A69JA29)

STANDARD CMOS SETUP
AWARD SOFTWARE, INC.
Date (mm:dd:yy) : Wed, Jun 14 1996
Time(hh:mm:ss) : 13 : 37 : 14
HARD DISKS TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE
Primary Master : Auto 0 0 0 0 0 0 Auto
Primary Slave : Auto 0 0 0 0 0 0 Auto
Secondary Master : Auto 0 0 0 0 0 0 Auto
Secondary Slave : Auto 0 0 0 0 0 0 Auto

Drive A : 1.44M, 3.5 in. Base Memory : 640K

Drive B : None Extended memory : 7168K
Other Memory : 384K
Video : EGA/VGA ------------------------------------------------
Halt On: All Errors Total Memory : 8192K
ESC : Quit áâàß:Select Item PU/PD/+/- : Modify
F1 : Help (Shift) F2 : Change Color

22
Date mm is month, dd is date, yy is year.
date from 1 to 31
month from Jan. to Dec.
year from 1900 to 2099

Time hh is hour, mm is minute, ss is second.

hh from 0 to 23 (24-hour military -time)
mm from 0 to 59
ss from 0 to 59

Primary Master These categories identify the types of the 2 channels

Primary Slave that have been installed in the computer. There
Secondary Master are 45 predefined types and 4 user definable
Secondary Slave types are for Enhanced IDE BIOS. Type 1 to 45
are predefined. Type ‘user’ is user-definable.
Press PgUp/PgDn to select a numbered hard
disk type or type the number and press<Enter>.
If you select ‘Auto’, the BIOS will auto-detect the
HDD & CD-ROM Drive at the POST stage and
show the IDE for HDD & CD-ROM Drive. If
you select ‘user’, you will need to know the
information listed below. Enter the information
directly from the keyboard and press <Enter>.
This information should be from your hard disk
vender or dealer. If the controller of the HDD
interface is ESDI, the selection shall be ‘Type 1’;
if SCSI, the selection shall be ‘None’.
If no device is installed select
‘NONE’ and press <Enter>.
Type drive type
SIZE automatically adjusts
CYLS number of cylinders
HEAD number of heads
PRECOMP write precom
LANDZ landing zone
SECTOR number of sectors
MODE mode type

23
Drive A This category identifies the types of floppy disk
Drive B drive A or drive B that have been installed in the computer.
None No floppy drive installed
360K, 5.25 in 5.25“ PC-type 360KB capacity
1.2M, 5.25 in 5.25“ AT-type 1.2MB capacity
720K, 3.5 in 3.5“ double-side 720KB capacity
1.44M, 3.5 in 3.5“ double-side 1.44MB capacity
2.88M, 3.5 in 3.5“ double-side 2.88MB capacity

Video This category selects the type of video adapter

used for the primary system monitor. Although
secondary monitors are supported, you do not
have to select the type in Setup.

Halt On This category determines whether the computer

will stop if an error is detectd during power up.
No errors The system boot will not be stopped
for any error that may be detected
All errors When the BIOS detects a non-fatal
error the system will be stopped and
you will be prompted
All, But The system boot will not stop for a
Keyboard keyboard error, it will stop for all other
errors
All, But The system boot will not stop for a disk
Diskette error, it will stop for all other errors
All, But The system boot will not stop for a disk
Disk/Key or keyboard error, it will stop for all
other errors

Memory This category is display-only which is determined

by POST (Power On Self Test) of the BIOS.
Base Memory The value of the base memory
is typically 512K or 640K based on the memory
installed on the mainboard.

24
Extended Memory How much extended
memory is present during the POST. This is
the amount of memory located above 1MB in
the CPU‘s memory address map.
Other Memory This refers to the memory
located in the 640K to 1024K address space.
The BIOS is the most frequent user of this RAM
area since this is where it shadows RAM.

25
This screen is a list of system configuration options. Some of them are defaults required by the
mainboard's design, others depend on the features of your system.

ROM PCI/ISA BIOS (2A69JA29)

CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP INTEGRATED PERIPHERALS
BIOS FEATURES SETUP SUPERVISOR PASSWORD
CHIPSET FEATURES SETUP USER PASSWORD
POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION
PNP/PCI CONFIGURATION SAVE & EXIT SETUP
LOAD BIOS DEFAULTS EXIT WITHOUT SAVING
LOAD SETUP DEFAULTS
ESC: Quit áâàß:Select Item
F10: Save & Exit Setup (Shift) F2 : Change Color
Virus, Protection, Boot Sequence

ROM PCI/ISA BIOS (2A69JA29)

BIOS FEATURES SETUP
AWARD SOFTWARE, INC.
Virus Warning : Disabled Video BIOS Shadow : Enabled
CPU Internal Cache : Enabled C8000-CBFFF Shadow : Disabled
External Cache : Enabled CC000-CFFFF Shadow : Disabled
Quick Power On Self Test : Enabled D0000-D3FFF Shadow : Disabled
Boot Sequence : A,C,SCSI D4000-D7FFF Shadow : Disabled
Swap Floppy Drive : Disabled D8000-DBFFF Shadow : Disabled
Boot Up Floppy Seek : Enabled DC000-DFFFF Shadow : Disabled
Boot Up NumLock Status : On
Boot Up System Speed : High
Gate A20 Option : Fast
Typematic Rate Setting : Disabled
Typematic Rate(Chars/Sec) :6 Esc : Quit áâàß:Select Item
Typematic Delay(Msec) : 250 F1 : Help PU/PD/+/- : Modify
Security Option : Setup F5 : Old Values (SHIFT)F2 : Color
PCI/VGA Palette Snoop : Disabled F6 : Load BIOS Defaults
Assign IRQ For VGA : Enabled F7 : Load Setup Defaults
OS Select for DRAM>64MB : Non-OS2

26
Virus Warning When this item is enabled, the BIOS will
monitor the boot sector and partition table of the
hard disk drive for any attempt at modification.
If an attempt is made, the BIOS will prompt
following error message will appear and wait for
user input . Many disk diagnostic programs which
attempt to access the boot sector table can
cause the above warning message. If you will
be running such a program, we recommend
that you first disable Virus Protection beforehand.

! WARNING !

Disk boot sector is to be modified

Type ‘Y’ to accept write or ‘N’ to abort write
Award Software, Inc.

Enabled Activates automatically when the system

boots up, if anything attempts to access
the boot sector or hard disk partition
table will cause a warning message to
appear.
Disabled No warning message will appear when
anything attempts to access the boot
sector or hard disk partition table.

CPU These two categories speed up memory access.

Internal Cache However, it depends on CPU/chipset design.
External Cache The default value is ‘enabled‘.

Quick Power On This category speeds up Power On Self Test

Self Test after you power up the computer. If you set
Enabled, BIOS will shorten or skip some checked
items during POST.

27
Boot Sequence This category determines which drive to search
first for the disk operating system (i.e., DOS).
Choices are A,C, SCSI; C, A, SCSI;
C, CDROM, A; CDROM, C, A; D, A, SCSI;
E, A, SCSI; F, A, SCSI; SCSI, A, C; SCSI, C, A;
and C only.

For example :
CDROM,C, A System will first search for CDROM
then HDD, and next is FDD
C,CDROM, A System will first search for HDD then
CDROM, and next is FDD
C is primary master; D is primary slave;
E is secondary master, F is secondary slave

Swap Floppy This item allows you to determine whether to

Drive enable the swap floppy drive or not.

Boot Up Floppy During POST, the BIOS will determine if the floppy
Seek disk drive installed is 40 tracks (360K) or 80
tracks (720K, 1.2M, 1.44M)
Enabled BIOS searches for floppy disk drive to
determine if it is 40 or 80 tracks
Disabled BIOS will not search for the type of
floppy disk drive by track number

Boot Up This allows you to determine the default state of

NumLock Status the numeric keypad. By default, the system
boots up with NumLock on.

Boot Up System Selects the default system speed - the normal

Speed operating speed at power up.

Gate A20 This entry allows you to select how the gate
Option A20 is handled. The gate A20 is a device used
to address memory above 1 MB. Normal is
keyboard; Fast is chipset.
28
Typematic Rate This determines if the typematic rate is to be used.
Setting When disabled, continually holding down a key
on your keyboard will generate only one key instance.

Typematic Rate When the typematic rate is enabled, this section

(Chars/Sec) allows you select the rate at which the keys are repeated.
6 6 characters per second
8 8 characters per second
10 10 characters per second
12 12 characters per second
15 15 characters per second
20 20 characters per second
24 24 characters per second
30 30 characters per second

Typematic Delay When the typematic rate is enabled, this section

(Msec) allows you select the delay between when the
key was first depressed and when the
acceleration begins.
250 250 msec
500 500 msec
750 750 msec
1000 1000 msec

Security Option This category allows you to limit access to the

system and Setup, or just to Setup
System The system will not boot and access to
Setup will be denied if the correct
password is not entered at the prompt
Setup The system will boot, but access to
Setup will be denied if the correct
password is not entered at the prompt
To disable security, select PASSWORD SETTING
at Main Menu and then you will be asked to enter
password. Do not type anything and just press
<Enter>, it will disable security. Once the security

29
 is disabled, the system will boot and you can enter
Setup freely.

PCI/VGA It determines whether the MPEG ISA/VESA

Palette Snoop VGA cards can work with PCI/VGA or not.
Enabled When PCI/VGA working with MPEG
ISA/VESA VGA Card
Disabled When PCI/VGA not working with
MPEG ISA/VESA VGA Card

OS Select for This item allows you to access the memory

DRAM > 64MB that is over 64MB in OS/2

Video BIOS Determines whether video BIOS will be copied to

Shadow RAM. However it is optional depending on
chipset design. Video Shadow will increase the
video speed.

C8000 - CBFFF These categories determine whether option

Shadow ROMs will be copied to RAM. An example of
DC000 - DFFFF such option ROM would be the support of onboard
Shadow SCSI.

Report No FDD For Windows 3.1x users set ‘NO’ (default); for
For WIN 95 Windows 95 users set ‘NO’ or ’YES’.

30
This screen controls the setting for the chipset on the mainboard.

ROM PCI/ISA BIOS (2A69JA29)

CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP INTEGRATED PERIPHERALS
BIOS FEATURES SETUP SUPERVISOR PASSWORD
CHIPSET FEATURES SETUP USER PASSWORD
POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION
PNP/PCI CONFIGURATION SAVE & EXIT SETUP
LOAD BIOS DEFAULTS EXIT WITHOUT SAVING
LOAD SETUP DEFAULTS
ESC: Quit áâàß:Select Item
F10: Save & Exit Setup (Shift) F2 : Change Color
AT Clock, DRAM Timmings, .......

ROM PCI/ISA BIOS (2A69JA29)

CHIPSET FEATURES SETUP
AWARD SOFTWARE, INC.
Auto Configuration : Enabled SDRAM CAS latency Time :3
DRAM Speed Selection : 60 ns CPU Waning Temperature : Disabled
MA Wait State : Slow *Current CPU Temperature : 39 o C/ 102 o F
EDO RAS# To CAS# Delay :3
EDO RAS# Precharge Time :3 Only if LM75 exist
EDO DRAM Read Burst (B/E/F) : x333
EDO DRAM Write Burst (B/E/F) : x222
DRAM Data Integrity Mode : Non-ECC
CPU-to-PCI IDE Posting : Enabled
System BIOS Cacheable : Disabled
Video BIOS Cacheable : Disabled
Video RAM Cacheable : Disabled
8-bit I/O Recovery Time :1
16-bit I/O Recovery Time :1
Memory Hole At 15M-16M : Disabled
Passive Release : Enabled Esc: Quit :Select Item
Delayed Transaction : Enabled F1 : Help PU/PD/+/-:Modify
AGP Aperture Size (MB) : 64 F5 : Old Values (Shift)F2 :Color
31
 SDRAM RAS-to-CAS Delay : Slow F6 :Load BIOS Defaults
SDRAM RAS Precharge Time : Slow

Auto Pre-defined values for DRAM, cache... timing

Configuration according to CPU type & system clock. When
this item is enabled, the pre-defined items will
become SHOW-ONLY.

DRAM Speed The DRAM speed is controlled by the DRAM

Selection timing Registers. The timings programmed into
this register are dependent on the system design.

DRAM RAS# DRAM must continually be refreshed or it will lose

Precharge Time its data. Normally, DRAM is refreshed entirely as
the result of a single request. This option allows
you to determine the number of CPU clocks
allocated for the Row Address Strobe to
accumulate its charge before the DRAM is
refreshed. If insufficient time is allowed, refresh
may be incomplete and data lost.

RAS# to When DRAM is refreshed, both rows and columns

CAS# Delay are addressed separately. This setup item allows
you to determine the timing of the transition from
RAS to Column Address Strobe (CAS).

DRAM Read This sets the timing for burst mode read (or
Burst (B/E/F) writes)from DRAM. Burst read and write
DRAM Write requests are generated by the CPU in four
Burst (B/E/F) separate parts. The first part provides the
location within the DRAM where the read or write
is to take place while the remaining three parts
provide the actual data. The lower the timing
numbers, the faster the system will address memory.

ISA Bus Clock This item allows you to select the PCI clock type.
Choices are PCI CLK/3; PCI CLK/4

System BIOS When enabled, accesses to the system BIOS

Cacheable ROM addressed at F0000H-FFFFFH are cached,

32
 provided that the cache controller is enabled.

Video BIOS As with changing the system BIOS above,

Cacheable enabling the Video BIOS cache will cause
access to video BIOS addressed at C0000H to
C7FFFH to be cached, if the cache controller is
also enabled.

8 Bit I/O The recovery time is the length of time, measured

Recovery Time in CPU clocks, which the system will be delay after
the completion of an I/O request. This item allows
you to determine the recovery time allowed for 8-
bit I/O. Choices are from NA, 1 to 8 CPU clocks.

16 Bit I/O This item allows you to determine the recovery

Recovery Time time allowed for 16-bit I/O. Choices are from NA,
1 to 4 CPU clocks.

Memory Hole At In order to improve performance, certain space

15M-16M in memory can be reserved for ISA cards. This memory
must be mapped into the memory below 16MB.

DRAM ECC/ During CPU reads of the DRAM, the 430HX

Parity Select provides error checking and correction or
parity of the data.

The BIOS will auto detect if the mainboard have LM75 components or not. If there
is LM75, the screen will show these LM75 related items, and these items are SHOWN
ONLY except “ CPU Warning Temperature“ The following are LM75 related items :

‘CPU Warning Temperature’ set the temperature for CPU warning. When the CPU
temperature reaches the setting temperature, the system will lower the CPU clock
according to the Throttle Duty Cycle.
‘Current CPU Temperature’ the current temperature of the CPU

33
This screen controls the 'green' features of this mainboard.

ROM PCI/ISA BIOS (2A69JA29)

CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP INTEGRATED PERIPHERALS
BIOS FEATURES SETUP SUPERVISOR PASSWORD
CHIPSET FEATURES SETUP USER PASSWORD
POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION
PNP/PCI CONFIGURATION SAVE & EXIT SETUP
LOAD BIOS DEFAULTS EXIT WITHOUT SAVING
LOAD SETUP DEFAULTS
ESC: Quit áâàß:Select Item
F10: Save & Exit Setup (Shift) F2 : Change Color
Sleep Timer, Suspend Timer, .....

ROM PCI/ISA BIOS (2A69JA29)

POWER MANAGEMENT SETUP
AWARD SOFTWARE, INC.
Power Management : Disabled *Reload Global Timer Events*
PM Control by APM : Yes IRQ [3-7, 9-15], NMI :Enabled
Video Off Method : V/H SYNC Primary IDE 0 :Disabled
+Blank Primary IDE 1 :Disabled
Video Off After : Standby Secondary IDE 0 :Disabled
Modem Use IRQ :3 Secondary IDE 1 :Disabled
Doze Mode : Disabled Floppy Disk :Disabled
Standby Mode : Disabled Serial Port :Enabled
Suspend Mode : Disabled Parallel Port :Disabled
HDD Power Down : Disabled
Throttle Duty Cycle : 62.5%
ZZ Active in Suspend : Disabled
VGA Active Monitor : Enabled
Soft-Off by PWR-BTTN : Instant-Off
CPUFAN Off In Suspend : Enabled Esc: Quit áâàß :Select Item
Resume by Ring : Enabled F1 : Help PU/PD/+/- : Modify
IRQ 8 Break Suspend : Disabled F5 : Old Values (Shift) F2: Color
F6 : Load BIOS Defaults

34
Power This category allows you to select the type (or
Management degree) of power saving and is directly related to
the following modes : Doze; Standby; Suspend;
HDD Power Down.
Disabled No power management. Disables all 4
modes
Min. Power Minimum power management. Doze
Saving =1hr.; Standby=1hr.; Suspend=1hr.;
HDD Power Down=15min
Max. Power Maximum power management only
Saving available for SL CPU‘s.Doze=1min.;
Standby=1min.;Suspend=1min.;HDD
Power Down=1min
User Allows you to set each mode
Defined indivi-dually. When not disabled, each
of the ranges are from 1min. to 1hr.
exect for HDD Power Down which
ranges from 1 to 15min. and disable
If you would like to use Software Power-off
Control function, you cannot choose
“Disabled ”here, and should select “Yes” in
PM Control by APM.

PM Control When enabled, an Advanced Power Management

by APM device will be activated to enhance the Max.
Power Saving Mode and stop the CPU internal
clock. If the Max. Power Saving is not enabled,
this will be shown as NO.

Video Off This determines the manner in which the monitor

Method is blanked.
V/H SYNC This selection will cause the system to
+ Blank turn off the vertical and horizontal sync.
ports and write blanks to the video
buffer
Blank This option only writes blanks to the
Screen video buffer

35
 DPMS Initial display power management
signaling

The Following 4 modes are Green PC power saving functions which are only user
configurable when ‘User Defined’ power management has been selected.

Doze Mode When enabled and after the set time of system
inactivity, the CPU clock will run at slower speed
while all other devices still operate at full speed

Standby Mode When enabled and after the set time of system
inactivity, the fixed disk drive and the video
would be shut off while all other devices still
operate at full speed

Suspend Mode When enabled and after the set time of system
inactivity, all devices except the CPU will be
shut off

HDD Power Down When enabled and after the set time of system
inactivity, the hard disk drive will be powered
down while all other devices remain active

Wake Up Events
In Doze & Standby

Power Down & These are I/O events whose occurrence can
Resume Events prevent the system from entering a power saving
mode or can awaken the system from such a
IRQ3 ~ IRQ15 mode. In effect, the system remains alert for
anything which occurs on a device which is
configured as On, even when the system is in a
powered down mode. When an I/O device wants to
gain the attention of the operating system, it
signals this by causing an IRQ (Interrupt ReQuests)
to occur. When the operating system is ready to
respond to the request, it interrupts itself and
performs the service. When set to off, activity will
neither prevent the system from going into a power
management mode nor awaken it.

36
This screen configures the PCI Bus slots.

ROM PCI/ISA BIOS (2A69JA29)

CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP INTEGRATED PERIPHERALS
BIOS FEATURES SETUP SUPERVISOR PASSWORD
CHIPSET FEATURES SETUP USER PASSWORD
POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION
PNP/PCI CONFIGURATION SAVE & EXIT SETUP
LOAD BIOS DEFAULTS EXIT WITHOUT SAVING
LOAD SETUP DEFAULTS
ESC: Quit áâàß:Select Item
F10: Save & Exit Setup (Shift) F2 : Change Color
IRQ Settings, Latency Timers, .....

ROM PCI/ISA BIOS (2A69JA29)

PNP/PCI CONFIGURATION
AWARD SOFTWARE, INC.
PNP OS Installed : No PCI IDE IRQ Map to : PCI-AUTO
Resources Controlled by : Auto Primary IDE INT# :A
Reset Configuration Data : Disabled Secondary IDE INT# :B

Esc: Quit áâàß :Select Item

F1 : Help PU/PD/+/- : Modify
F5 : Old Values (Shift) F2: Color
F6 : Load BIOS Defaults

37
Resource The Award Plug and Play BIOS has the capability
Controlled by to automatically configure all of the boot and Plug
and Play compatible devices. However, this
capability means absolutely nothing unless you
are using a Plug and Play OS such as Windows 95
Choices are Auto and Manual

Reset Config- This item allows you to determine whether to reset the
uration Data configuration data or not.

PCI IRQ This sets the method by which the PCI bus reco-
Actived By gnizes that an IRQ service is being requested by a
device. Under all circumstances, you should retain
the default configuration unless advised otherwise
by your system‘s manufacturer.
Choices are Level and Edge.

PCI IDE IRQ This allows you to configure your system to the
Map To type of IDE disk controller in use. If you have
equipped your system with a PCI controller,
changing this allows you to specify which slot holds
the controller and which PCI interrupt (A,B,C,D) is
associated with the connected hard disk. Select
‘PCI Auto’ allows the system to automatically
determine how your IDE disk system is configured.

38
This section page includes all the items of IDE hard drive and Programmed
Input/Output features. See also Section “Chipset Features Setup”.

ROM PCI/ISA BIOS (2A69JA29)

CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP INTEGRATED PERIPHERALS
BIOS FEATURES SETUP SUPERVISOR PASSWORD
CHIPSET FEATURES SETUP USER PASSWORD
POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION
PNP/PCI CONFIGURATION SAVE & EXIT SETUP
LOAD BIOS DEFAULTS EXIT WITHOUT SAVING
LOAD SETUP DEFAULTS
ESC: Quit áâàß:Select Item
F10: Save & Exit Setup (Shift) F2 : Change Color
Time, Date, Hard Disk Type .....

ROM PCI/ISA BIOS (2A69JA29)

INTEGRATED PERIPHERALS
AWARD SOFTWARE, INC.
IDE HDD Block Mode : Enabled Onboard Parallel Port : 378H/IRQ7
IDE Primary Master PIO : Auto Onboard Parallel Mode : ECP
IDE Primary Slave PIO : Auto ECP Mode Use DMA : 3
IDE Secondary Master PIO : Auto
IDE Secondary Slave PIO : Auto
IDE Primary Master UDMA : Auto
IDE Primary Slave UDMA : Auto
IDE Secondary Master UDMA : Auto
IDE Secondary Slave UDMA : Auto
On-Chip Primary PCI IDE : Enabled
On-Chip Secondary PCI IDE : Enabled
USB Keyboard Support : Disabled

KBC input clock : 8 MHz Esc: Quit áâàß :Select Item

Onboard FDD Controller : Enabled F1 : Help PU/PD/+/- : Modify
Onboard Serial Port 1 : 3F8/IRQ4 F5 : Old Values (Shift) F2: Color
Onboard Serial Port 2 : 3F8/IRQ3 F6 : Load BIOS Defaults
39
 UART Mode Select : Normal

IDE HDD Block This allows your HD controller to use the fast block
Mode mode to transfer data to and from your HD drive
Enabled IDE controller uses block mode
Disabled IDE controller uses standard mode

PCI Slot IDE This item allows you designate an IDE controller
2nd Channel board inserted into one of the physical PCI slots as
your secondary IDE
Enabled External IDE controller designated as the
secondary controller
Disabled No IDE controller occupying a PCI slot

On-Chip Primary This setup item allows you to either enable or

PCI IDE disable the primary/secondary controller. You might
On-Chip Second- choose to disable the controller if you were to add
ary PCI IDE a higher performance or specialized controller.

IDE Primary PIO - Programmed Input/Output, it allows the

Master/Slave PIO BIOS to tell the controller what it wants and then
IDE Secondary let the controller and the CPU to complete the
Master/Slave PIO task by themselves. This is simpler and more faster.
Your system supports five modes, 0 - 4, which
primarily differ in timing. When Auto is selected,
the BIOS will select the best available mode.

UART 2 Mode This lets you select the Infrared mode. Choices are
Standard, HPIR, and ASKIR. If you choose HPIR or
ASKIR mode, the screen will show another two
lines to let you choose ‘IR Function Duplex’ (Full
or Half) and‘RxD TxD Active’ (Hi Lo; Lo Hi; Hi Hi;
Lo Lo).

40
 ROM PCI/ISA BIOS (2A69JA29)
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP INTEGRATED PERIPHERALS
BIOS FEATURES SETUP SUPERVISOR PASSWORD
CHIPSET FEATURES SETUP USER PASSWORD
POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION
PNP/PCI CONFIGURATION SAVE & EXIT SETUP
LOAD BIOS DEFAULTS EXIT WITHOUT SAVING
LOAD SETUP DEFAULTS
ESC: Quit áâàß:Select Item
F10: Save & Exit Setup (Shift) F2 : Change Color
Time, Date, Hard Disk Type .....

ROM PCI/ISA BIOS (2A69JA29)

CMOS SETUP UTILITY
AWARD SOFTWARE, INC.

Hard Disks Type Size CYLS HEAD PRECOMP LANDZ SECTOR MODE
Primary Master :

Select Primary Master Option (N=Skip) : N

Options Size CYLS Head PRECOMP LANDZ Sector Mode
2(Y) 1337 648 64 0 2594 63 LBA
1 1339 2595 16 65535 2594 63 NORMAL
3 1338 1297 32 65535 2594 63 LARGE
Note : Some OS (like SCO-UNIX) must use “Normal” for installation
ESC : Skip

41
The last step is 'save and exit'. If you select this item and press 'Y', then these records will be saved
in the CMOS memory on the mainboard. It will be checked every time you turn your computer on.

ROM PCI/ISA BIOS (2A69JA29)

CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP INTEGRATED PERIPHERALS
BIOS FEATURES SETUP SUPERVISOR PASSWORD
CHIPSET FEATURES SETUP USER PASSWORD
POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION
PNP/PCI CONFIGURATION SAVE & EXIT SETUP
LOAD BIOS DEFAULTS EXIT WITHOUT SAVING
LOAD SETUP DEFAULTS
ESC: Quit áâàß:Select Item
F10: Save & Exit Setup (Shift) F2 : Change Color
Time, Date, Hard Disk Type .....

ROM PCI/ISA BIOS (2A69JA29)

STANDARD CMOS SETUP
AWARD SOFTWARE, INC.

STANDARD CMOS SETUP INTEGRATED PERIPHERALS

BIOS FEATURES SETUP PASSWORD SETTING
CHIPSET FEATURES SETUP IDE HDD AUTO DETECTION
POWER MANAGEMENT SETUP SAVE & EXIT SETUP
PNP/PCI CONFIGURATION EXIT WITHOUT SAVING
LOAD BIOS DEFAULTS SAVE to CMOS and EXIT (Y/N):Y

ESC: Quit áâàß:Select Item

F10: Save & Exit Setup (Shift) F2 : Change Color
Save Data to CMOS & Exit SETUP

42
LOAD BIOS DEFAULTS
When your mainboard has problems and needs to
troubleshoot the system, you can use this function.
The default values loaded only affect the BIOS Features
Setup, Chipset Features Setup, Power Management
Setup and PNP/PCI Configuration Setup. There is no
effect on the Standard CMOS Setup. To use this function,
select it from main menu and press <Enter>. A line will
appear on the screen asking if you want to load the BIOS
default values. Press <Yes> and <Enter> then the BIOS
default values will be loaded.

LOAD SETUP DEFAULTS

This allows you to load optimal settings which are stored in
the BIOS ROM. The default values loaded only affect the
BIOS Features Setup, Chipset Features Setup, Power
Management Setup and PNP/PCI Configuration Setup.
There is no effect on the Standard CMOS Setup. To use
this function, select it from main menu and press <Enter>.
A line will appear on the screen asking if you want to load
the Setup default values. Press <Yes> and <Enter> then
the Setup default values will be loaded.

SUPERVISOR PASSWORD / USER PASSWORD

This allows you to set the password. The mainboard defaults with
password disabled.
Enter/Change password : Enter the current password, at
the prompt, key-in your new password (up to eight
alphanumeric characters), press <Enter>. At the next
prompt, confirm the new password by typing it again and press
<Enter>.
Disable password : Press the <Enter> key instead of
entering a new password when the ‘Enter Password’
dialog box appears. A message will appear confirming that
the password is disabled.

If you set both supervisor and user passwords, only the

43
 supervisor password allows you to enter the BIOS SETUP
program.

CAUTION :If you forgot your password, you must disable

the CMOS by turning power off and set JP10 to ‘close‘. And then
open reload the system.

IDE HDD AUTO DETECTION

This allows you to detect the IDE hard disk drivers‘ parameters
and enter them into ‘Standard CMOS Setup’ automatically.

If the auto-detected parameters displayed do not

match the ones that should be used for your hard drive,
do not accept them. Press <N> to reject the values
and enter the correct ones manually on the Standard
CMOS Setup screen.

SAVE & EXIT SETUP

This allows you to save the new setting values in the
CMOS memory and continue with the booting process.
Select what you want to do, press <Enter>.

EXIT WITHOUT SAVING

This allows you to exit the BIOS setup utility without
recording any new values or changing old ones.

44
 Control Key Description

UP ARROW Move to previous item

DOWN ARROW Move to next item
LEFT ARROW Move to the item in the left hand
RIGHT ARROW Move to the item in the right hand
Esc KEY Esc Main Menu : Quit and not save
changes
Setup menu : Exit current page and
return to main menu
PgUp KEY Increase the numeric value or make
changes
PgDn KEY Decrease the numeric value or make
changes
F1 KEY Help General help
F2 KEY Shift +F2 Change color from total 16 colors
F5 KEY Old Value Restore the pervious CMOS value
from CMOS
F6 KEY Load BIOS Load the default CMOS value from
default BIOS default table
F7 KEY Load setup Load Setup default
default
F10 KEY Save & Exit Save all the CMOS changes and Exit
Setup setup, only for Main Menu

45
APPENDIX A
TECHNICAL SUPPORT REQUEST FORM
If the mainboard doesn't function properly, please complete the following
information and return it to your system dealer. If the further information is
needed, please attach it.

Model No : ATC-6120 Date of Purchase : ______________

Serial No : ___________________

HARDWARE :
BRAND MODEL SPEED Q'TY
SIM Module

CPU SPEED : ________ MHz

DRAM :______MB (__ EDO, __FastPage, __ECC)
Hard Disk Interface Controller : _____ IDE, ____ SCSI
Hard Disk Brand :___________, Model :_________, Capacity :________
Display Controller Brand :_____________,Model :__________
Controller Chip Brand :_____________,Model :__________
SOFTWARE:
AWARD SYSTEM BIOS: Version _________ Date Code _____________
Keyboard BIOS: Brand __________

Other Add-on Cards Information:

Add-on Card Bus Interface Model Remark

Error Description :

46