Product Catalogue

BACK TO MAIN MENU
BACK TO MAIN MENU
BACK TO MAIN MENU
BACK TO CORROSION MONITORING MENU
1 THE GALLOWAY CENTRE, HAMBRIDGE LANE, NEWBURY, BERKS, RG14 5TL ENGLAND TELEPHONE (01635) 552225 FAX: (01635) 568690 EMAIL: [email protected]
ROSE CORROSION SERVICES LIMITED
MS0500 E/R Corrosion Meter The MS0500 is a battery-powered, portable corrosion meter capable of interpreting all electrical resistance type corrosion probes. Combining a light weight of only 4 pounds with ease of operation, the MS0500 enables the operator to take readings from several different probe locations. The unit comes in a convenient leather carrying case. Corrosion rate measurements are made using the electrical resistance method. The electrical resistance method has a wide range of applications since it can be used in conductive or non-conductive environments including oil and gas. The unit measures the change in resistance of the probe element as metal loss occurs. The rate of change is directly proportional to the corrosion rate. The MS0500 has a permanently attached cable that the operator can simply connect to a probe and take the reading. A selector switch is provided on the units display panel for indicating the probe element type to be read. All electrical resistance probe types can be used with this unit, including wire loop, tube loop, cylindrical and flush mount probes.
BACK TO ELECTRICAL RESISTANCE MENU
SCROLL DOWN FOR SECOND PAGE
Technical Specifications E/R Probe Configurations:

Wire Loop WIRE Probe verification CHECK Tube Loop TUBE Others (Flush, Strip, Loop, Etc.) DUAL Cylindrical SPEC
Dimensions with Leather Case:

Height: Width: Depth:
4.4 inches (11.2cms) 9.0 inches (22.9cms) 8.0 inches (20.3cms)
Dimensions without Leather Case:

Height: Width: Depth:
3.0 inches (7.6cms) 5.0 inches (12.2cms) 6.75 inches) (17.2 cm) 4 pounds, 12 ounces (2.2kg)
Weight with Leather Case:
Weight without Leather Case: 2 pounds, 4 ounces (1.0kg) Power Requirements: Temperature Range: Two 9 volt alkaline batteries 32 to 120 F (0 to 50 C)
Operational Humidity Range: 30% to 90% Storage Humidity Range: 5% to 95%
Length of Connecting Cable: 6 feet (2 metres) Intrinsic Safety:

BASEEFA certified EEx ib [ia] IIB T2 Equivalent to: North American Class 1 Division 1 Zone 0 Temperature T2 IN0500
Part #
1 THE GALLOWAY CENTRE, HAMBRIDGE LANE, NEWBURY, BERKS, RG14 5TL ENGLAND TELEPHONE +44(0)1635 552225 FAX: +44(0)1635 568690 EMAIL: [email protected]
MS1500E Corrosion Meter

The MS1500E is an intrinsically-safe, battery-powered, hand-held corrosion meter that enables you to directly take measurements from an electrical resistance probe, store the data, and upload directly to a computer. The unit features an easy-to use Main Menu that will permit even an operator who is unfamiliar with the unit to take readings with ease. Corrosion rate measurements are made using the electrical resistance method. The electrical resistance method has a wide range of applications since it can be used in conductive or nonconductive environments including oil and gas. The unit measures the change in resistance of the probe element as metal loss occurs. The rate of change is directly proportional to the corrosion rate. After taking and storing a reading, the operator can display the metal loss in mils and the corrosion rate in mils per year (mpy). All measurements made with the unit are automatically time and date stamped with the internal real time clock. If the detects a probe with an internal leak or damaged element, a CHECK FAILED message occurs. The unit can take up to 3000 readings and can be used with up to 150 probes. All stored readings are protected by a lithium back-up battery to prevent loss. Data may be selectively deleted from memory to accommodate additional information once the 3000 reading capacity is reached. Alternatively, information may be downloaded to an IBM compatible PC as a comma delimited ASCII file for import into any of the standard data handling and analysis programs (e.g., EXCEL, LOTUS 123, Quattro Pro). The MS1500E may also be used as a data collection and transfer terminal for the remote data logger. Accumulated data from several field-based units may be locally downloaded to the MS1500E hand-held terminal, and then transferred to a PC for further analysis. The MS1500E may also be used as a data collection and transfer terminal for the remote data logger. Accumulated data from several field-based units may be locally downloaded to the MS1500E hand-held terminal, and then transferred to a PC for further analysis. The MS1500E offers seven operating modes: Select Probe, Make Measurements, Compute, Recall, Delete Readings, Communicate, and Set Time and Date. All electrical resistance probe types can be used with this unit, including wire loop, tube loop, cylindrical element, surface strip, and flush mount probes.

Technical Specifications
E/R Probe Configurations: Wire Loop Tube Loop Surface Strip Flush Mount Cylindrical Element
Operating Temperature Range: Storage Temperature Range: Operational Humidity Range: Storage Humidity Range: Weight: Dimensions: Battery: Battery Life: Memory Protection:
32F to 122F (0C to 50C) -4F to 158F (-20C to 70C) 30% - 90% 5% - 95% 1.5 lbs. (5.2 lbs. with hardshell case) 7.63 inches (h) x 4.15 inches (w) x 2.00 inches (d) 194 mm (h) x 105 mm (w) x 50 mm (d) Three 1.5V AA Alkaline 8 hours of continuous use 10-year battery, back-up life
Maximum # of Probe Storage Files: 150 Maximum # of Stored Readings: Measurements/Computation: Communication Port: Display: Part #: 3100 Probe Life (0-100.0%) Metal Loss (Mils/Year) RS-232 Serial Port 4-Line x 20 character LCD Panel IN1500
Intrinsic Safety:
Class 1, Division 1 Groups A, B, C and D Temperature Code T3C Class I, Zone 0 Group IIC, T3C Conforms to ANSI UL Std. 913
MS2500E Transmitter
The MS2500E is a microprocessor controlled transmitter that features transmission through a 4- 20mA current loop. The unit is designed to provide a direct linear measurement of corrosion occurring at a specific location. The MS2500E is encased in a UL-approved explosion and weather proof NEMA enclosure. Operating temperatures range from 0o F to 140o F. The unit provides excellent results with all electrical resistance probes, especially the wire and tube loop types. The instrument is supplied with a 5-foot instrument-to-probe extension cable with connector. Information can be transmitted to the MS2510 Receiver or a customer-supplied data receiver via a 4 - 20mA current loop. The 4 -20mA signal range permits the unit to be used with a variety of receivers with minimal programming required by the user. Programming is based on the simple formula: PM(mA-4) =M L 16 Where: PM = probe multiplier mA = milliamp reading M L = metal loss in mils Corrosion rate measurements are made with the electrical resistance method. The electrical resistance method has a wide range of applications since it can be used in conductive or non-conductive environments including oil and gas. The unit measures the change in resistance of the probe element as metal loss occurs. The rate of change is directly proportional to the corrosion rate.

Technical Specifications MS2500E Transmitter (BASEEFA Certified)
E/R Probe Selections: Weight: Power Requirements: Output: Operating Temperature Range: Storage Temperature Range: Dimensions: Mounting Requirements:
Enclosure:
Intrinsic Safety: Part #:
Switch selectable for Wire Loop, Tube Loop, Cylindrical Element and special 5.02 lbs. (2.28kg) 10 to 35 VDC 4 - 20mA linear signal 0F to 140F (-18C to 60C) -40F to 176F (-40C to 80C) 5.81 Long x 4.50 Wide x 4.81 Deep (14.76cms x 11.43cms x 12.22cms) Mounting hardware is supplied with the unit. It may be mounted up to 5 feet (1.5 metres) from the probe location to a flat surface or pipe. Explosion Proof (FM, CSA, CENELEC, UL) Class I, Groups B, C, D, Class II, Groups E, F, G, Class III, CENELEC: Eexd IIC NEMA 4X, 7BCD, 9EFG Certified to CAN/CSA STD E79-0-95 & E79-11-95 Class I, Division 1, Groups C and D, T4 IN2500
MS2510 Receiver (BASEEFA Certified) Power Requirements: 1120/240V/60/50Hz Maximum transmitter to receiver 10,000 ft (3048m) Range: Weight: 4 lbs. (1.9kg) 8.25 Long x 10.00 Wide x 6.00 Deep Dimensions: (20.96cms x 25.40cms x 15.24cms) 25V DC 4-20mA current loop drive/4-20mA and Output: 0-10 Volts isolated output to recorder, CPU, etc. Storage Temperature Range: -40F to 176F (-40C to 80C) Three-digit LED display. Three-position switch Display: permits display of Loop Current (mA), Probe Life: (0-1000 units), and Metal Loss (mils) Part #: IN2510
MS3500E Data Logger
The MS3500E is a completely self-contained data logger for electrical resistance type probes. The MS3500E can be installed directly onto any type of electrical resistance probe and, once in place, will automatically read the probe at pre-selected time intervals and store the resulting data in the units internal memory. The internal memory will collect up to 3000 data points before data download as required. The data collection interval is programmable in hourly increments. Even at the minimum data collection interval (1 hour), data downloading need only be performed every eighty days. With more practical data collection intervals (8-12 hours), the unit may be unattended for as long as 6-8 months between downloading operations. The internal battery is capable of supplying the power requirements needed for months of continuous operation. The unit also has an auxiliary battery backup to prevent the loss of data in the event of main battery failure. The MS3500E has a unique optical, infrared, RS232 communication link that is used to download the stored data either to an MS1500E portable E/R data logger or a laptop PC (IBM compatible). The optimal communication link is an integral part of the intrinsically safe design of the unit. Because the signal is optical and not electrical, it permits the unit to download data in hazardous areas without removing the instrument. Once the data is downloaded, it may be analyzed, reviewed, or reported by conventional spreadsheet, data base, or mathematical software packages. Another unique feature of the MS3500E is the high level of internal intelligence. The two-line, 20-character LCD allows visual review of all historical data in memory and reads directly as "Total Metal Loss" and/or "Average Corrosion Rate". The LCD screen, together with the two-key membrane keypad, provides a user friendly, interactive, prompting system that is used for both system setup and data review. This makes the MS3500E the most advanced unit of its type on the market. The MS3500E comes in a NEMA 4X (IP 65) enclosure. An optional feature of the unit is the addition of a 4-20mA continuous output transmitter.

Functions: Display: Control: Memory Capacity: Read Interval: Communication Link: Enclosure:
Total Metal Loss (mls) Average Corrosion Rate (mpy) Two-line LCD, 20 characters Two-key membrane keypad 3100 readings, screen reviewable using scroll feature Programmable, hourly increments (1-1000) Infrared, RS232 (standard), 4-20mA (optional)
NEMA 4X (IP65) 11.50 inches (h) x 8.94 inches (w) x 4.00 inches (d) Dimensions: 292 mm (h) x 227 mm (w) x 102 mm (d) (NEMA 4X) Power: Six 1.5V "AA" Dry Cell Batteries Weight: 11.94lbs (5.42kg) IN3500 (Remote E/R Data Logger) Part #: IN3510 (Remote E/R Data Logger with 4-20mA output transmitter) Class 1, Division 1 Groups A, B, C and D Temperature Code T3C Intrinsic Safety: Class I, Zone 0 Group IIC, T3C Conforms to ANSI UL Std. 913

ER0250 ATMOSPHERIC PROBE
Model ER0250 is a probe used to monitor corrosion in atmospheric environments. The probe consists of an element which is mounted onto an epoxy board. One side of the element is exposed to the corrosive environment while the other side is covered, acting as a reference element. The ER0250 connects to a special cable that allows it to be used with electrical resistance probe instrumentation. Replacement elements may be ordered without cable. The probe comes with a 3/16" hole for easy mounting.
Specifications: Probe Body Temperature Rating Standard Element sizes
Epoxy 250 F/121 C 4 or 8 mils (useful range is half of thickness)

ER0250 ORDERING INFORMATION
Model AP11 Atmospheric Probe Element Thickness 04 4 mil thickness (2 mil useful probe life) 08 8 mil thickness (4 mil useful probe life) Element Alloy XXX Use Code in Alloy Chart Cable Length 00 No Cable 10 10ft Cable 20 20ft Cable AP11 8 375 20 Example of Probe Ordering# For alloys, sizes, or other special requirements not listed, contact our sales department. Code 375 538 541 186 141 Description C1010 5Cr 1/2Mo 9Cr 1Mo 410 S.S 304 S.S Alloy Chart UNS# Code G10100 159 K42544 A12 K90941 602 S41000 419 S30400 434 Description 316L S.S C276 Alloy 625 CDA110 CDA443 UNS# S31603 N10276 N06625 C11000 C44300
Note: Not all alloys are available with all element types and seals.
ER0500 - ELECTRICAL RESISTANCE PROBE SURFACE STRIP ELEMENT AND CYLINDRICAL ELEMENT TYPES
Model ER0500 probes are designed for heavy duty service conditions such as underground and structural monitoring of pipelines, vessels, above and below ground storage tanks and structures - whether cathodically protected or not. The surface strip element assembly is suited to the "construction site" environment. The cylindrical element is economical and durable. Its slim profile is convenient for locations with restricted access such as concrete bridge structures and other infrastructure applications. Both probes provide good sealing of the reference element and the check element provides confidence in the continued performance of the corrosion sensor. Either probe may or may not be connected to a cathodically protected structure. Connection of a ground cable allows the probe to measure the effectiveness of the Cathodic Protection (C.P.) System under all the operating conditions. If unconnected to the structure, the probe monitors the direct corrosivity of the soil or environment. The probes may be ordered with or without a grounding lead for a C.P. System. The lead may be installed at the probe or connector end, whichever is most convenient. In most cases, a lead at the monitoring connector end is preferred, with a separate lead running to the vessel or C.P. System. This enables connection to the C.P. System to be made as required - even after probe installation. Specifications: Surface Strip Probe Body Cable Connection Epoxy Block Heavy Duty Length Cylindrical All welded element Heavy Duty Length with Bonded Heat Shrink Sleeving onto Element

Model AP
Electrical Resistance Probe Type 31 40 61 70 Under ground surface strip without ground strap Under ground cylindrical with ground strap Under ground surface strip with ground strap Under ground cylindrical without ground strap Element Thickness 10 mil thickness (5 mil useful probe life) - cylindrical or surface 10 strip 20 mil thickness (10 mil useful probe life) - cylindrical or surface 20 strip 40 40 mil thickness (20 mil useful probe life) - surface strip only 50 50 mil thickness (25 mil useful probe life) - cylindrical only Element Alloy XXX Use Code in Alloy Chart Cable Length 10 10ft cable 20 20ft cable 40 375 20 Example of Probe Ordering #
AP
31
For alloys, sizes, or other special requirements not listed, contact our sales department. Code Description 375 C1010 538 5Cr 1/2Mo 541 9Cr 1Mo 186 410 S.S 141 304 S.S Alloy Chart UNS# Code G10100 159 K42544 A12 K90941 602 S41000 419 S30400 434 Description 316L S.S C276 Alloy 625 CDA110 CDA443 UNS# S31603 N10276 N06625 C11000 C44300

Model ER 1000 - Electrical Resistance Probe with Fixed Length 1/2" NPT Pipe Plug Mount and Loop Element
Model ER1000 Electrical Resistance Probe is a fixed-insertion-length probe with a " NPT pipe plug. The probe process isolation or process shutdown to install and a threaded pipe fitting to mount. With a maximum diameter of ", the probe is ideal for applications where space is limited. The probe consists of an insertion rod with an element, a hermetically sealed connector, a " NPT fitting, and a velocity shield, which are all welded in place. Several standard loop elements and lengths are available to meet your specific needs. (Refer to the Element and Alloy Selection Chart for more information).
Specifications: Probe Body Element Seal Fill Material Temperature Rating Pressure Rating Mounting 316 Stainless Steel Glass or Teflon Ceramic 500 F/260 C 1000 PSI/68 Bar 0.5 inch NPT Fitting

Model ER11
ER3
Electrical Resistance 0.5 inch NPT Pipe Plug Probe Probe Body Material 2 316 3 C276 E/R Element Options 00 WR40 Wire Loop - 40 mil thickness (10 mil useful probe life) 10 WR80 Wire Loop - 80 mil thickness (20 mil useful probe life) 20 TU04 Tube Loop - 4 mil thickness (2 mil useful probe life) 30 TU08 Tube Loop - 8 mil thickness (4 mil useful probe life) 40 TU16 Tube Loop - 16 mil thickness (8 mil useful probe life) Seal Type 1 Glass 2 Teflon 3 Epoxy Length 06 4.08 inches max. insertion length 08 7.08 inches max. insertion length 12 11.08 inches max. insertion length 18 17.08 inches max. insertion length Element Alloy XXX Use Code in Alloy Chart E/R Probe Options 00 No Shield 03 Shield 2 10 1 O8 375 O3 Example of Probe Ordering #
For alloys, sizes, or other special requirements not listed, contact our sales department. Code 375 538 541 186 141 Description C1010 5Cr 1/2Mo 9Cr 1Mo 410 S.S 304 S.S Alloy Chart UNS# Code G10100 159 K42544 A12 K90941 602 S41000 419 S30400 434 Description 316L S.S C276 Alloy 625 CDA110 CDA443 UNS# S31603 N10276 N06625 C11000 C44300

Model ER 2000 - Electrical Resistance Probe with Fixed Length NPT Pipe Plug Mount and Loop Element
Model ER2000 Electrical Resistance Probe is a fixed-insertion-length probe with a " or 1" NPT pipe plug. The probe requires process isolation or process shutdown to install and a threaded pipe fitting to mount. The probe assembly consists of an insertion rod with an element, a hermetically sealed connector, a " or 1" NPT fitting, and a velocity shield, which are all welded in place. Several standard loop elements and lengths are available to meet your specific needs. (Refer to the Element and Alloy Selection Chart for more information)
Specifications: Element Seal Fill Material Temperature Rating Pressure Rating Mounting Probe Body Glass or Teflon Ceramic or Epoxy 500 F / 260 C 4000 PSI/277 Bar 0.75 inch or 1 inch NPT Fitting (please specify size required) 316 Stainless Steel
STD. LENGTH 8" 12" 18"

Model ER2 Electrical Resistance Fixed Length Pipe Plug Probe Pipe Plug Size 2 0.75 inch NPT Pipe Plug 3 1 inch NPT Pipe Plug Probe Body Material 22 316 44 C276 E/R Element Options 00 WR40 Wire Loop - 40 mil thickness (10 mil useful probe life) 10 WR80 Wire Loop - 80 mil thickness (20 mil useful probe life) 20 TU04 Tube Loop - 4 mil thickness (2 mil useful probe life) 30 TU08 Tube Loop - 8 mil thickness (4 mil useful probe life) 40 TU16 Tube Loop - 16 mil thickness (8 mil useful probe life) 80 SL04 Strip Loop - 4 mil thickness (1 mil useful probe life) 90 SL08 Strip Loop - 8 mil thickness (2 mil useful probe life) Seal Type 1 Glass 2 Teflon 3 Epoxy Length 06 5.13 inches max. insertion length 08 7.13 inches max. insertion length 12 11.13 inches max. insertion length 18 17.13 inches max. insertion length Element Alloy XXX Use Code in Alloy Chart E/R Probe Options 00 No Shield 03 Shield ER2 2 22 10 1 8 375 3 Example of Probe Ordering #
For alloys, sizes, or other special requirements not listed, contact our sales department.
Code 375 538 541 186 141 Description C1010 5Cr 1/2Mo 9Cr 1Mo 410 S.S 304 S.S Alloy Chart UNS# Code G10100 159 K42544 A12 K90941 602 S41000 419 S30400 434 Description 316L S.S C276 Alloy 625 CDA110 CDA443 UNS# S31603 N10276 N06625 C11000 C44300

Model ER 2100 - Electrical Resistance Probe with Fixed Length NPT Pipe Plug Mount and Loop Element
Model ER2100 Electrical Resistance Probe is a fixed-insertion-length probe with a " NPT pipe plug. The probe requires process isolation or process shutdown to install and a threaded pipe fitting to mount. The all-welded construction allows the probe to be used in harsh environments. The probe assembly consists of an insertion rod with an element, a hermetically sealed connector, and a " NPT fitting, which are all welded in place. A velocity shield can be provided if required. Several standard elements and lengths are available to meet your specific needs. (Refer to the Element and Alloy Selection Chart for more information).
Specifications: Probe Body Element Seal Fill Material Temperature Rating Pressure Rating Mounting STD. LENGTH 8" 12" 18" 316 Stainless Steel Welded Ceramic 500 F/260 C 4000 PSI/277 Bar 0.75 inch NPT Fitting

Model ER2 Electrical Resistance Fixed Length Pipe Plug Probe Pipe Plug Size 2 0.75 inch NPT Pipe Plug 3 1 inch NPT Pipe Plug Probe Body Material 22 316 44 C276 E/R Element Options 500 CT10 Cylindrical - 10 mil thickness (5 mil useful probe life) 600 CT20 Cylindrical - 20 mil thickness (10 mil useful probe life) 700 CT50 Cylindrical - 50 mil thickness (25 mil useful probe life) Length 06 8.38 inches max. insertion length 08 10.38 inches max. insertion length 12 14.38 inches max. insertion length 18 20.38 inches max. insertion length Element Alloy XXX Use Code in Alloy Chart E/R Probe Options 00 No Shield 03 Shield ER2 2 22 500 O8 375 O3 Example of Probe Ordering # For alloys, sizes, or other special requirements not listed, contact our sales department. Code 375 538 541 186 141 Description C1010 5Cr Mo 9Cr 1Mo 410 S.S 304 S.S Alloy Chart UNS# Code G10100 159 K42544 A12 K90941 602 S41000 419 S30400 434 Description 316L S.S C276 Alloy 625 CDA110 CDA443 UNS# S31603 N10276 N06625 C11000 C44300
Model ER 3000 Electrical Resistance Probe with Adjustable Length inch NPT Pipe Plug Mount and Loop Element
Model ER3000 Electrical Resistance Probe is an adjustable-insertion-length probe with a " NPT compression fitting. The compression fitting allows the probe to be inserted into the process to the required length. The probe requires process isolation or process shutdown to install and a threaded pipe fitting to mount. The probe consists of an insertion rod with an element, a hermetically sealed connector, a compression fitting and a safety nut to prevent blow out. A velocity shield can be added to the assembly if required. Several standard loop elements and lengths are available to meet your specific needs. (Refer to the Element and Alloy Selection Chart for more information).
Specifications: Probe Body Element Seal Fill Material Temperature Rating Pressure Rating Mounting 316 Stainless Steel Glass or Teflon Ceramic 500 F/260 C 1500 PSI/102 Bar 0.75 inch NPT Fitting

Model ER3 Electrical Resistance Adjustable Pipe Plug Probe Pipe Plug Size 2 0.75 inch NPT Pipe Plug 3 1 inch NPT Pipe Plug Probe Body Material 22 316 44 C276 E/R Element Options 00 WR40 Wire Loop - 40 mil thickness (10 mil useful probe life) 10 WR80 Wire Loop - 80 mil thickness (20 mil useful probe life) 20 TU04 Tube Loop - 4 mil thickness (2 mil useful probe life) 30 TU08 Tube Loop - 8 mil thickness (4 mil useful probe life) 40 TU16 Tube Loop - 16 mil thickness (8 mil useful probe life) 80 SL04 Strip Loop - 4 mil thickness (1 mil useful probe life) 90 SL08 Tube Loop - 8 mil thickness (2 mil useful probe life) Seal Type 1 Glass 2 Teflon 3 Epoxy Length 06 5.33 inches max. insertion length 08 7.33 inches max. insertion length 12 11.33 inches max. insertion length 18 17.33 inches max. insertion length Element Alloy XXX Use Code in Alloy Chart E/R Probe Options 00 No Shield 03 Shield ER3 2 22 10 1 O8 375 O3 Example of Probe Ordering #
Code 375 538 541 186 141 Description C1010 5Cr 1/2Mo 9Cr 1Mo 410 S.S 304 S.S Alloy Chart UNS# Code Description G10100 159 316L S.S K42544 A12 C276 K90941 602 Alloy 625 S41000 419 CDA110 S30400 434 CDA443 UNS# S31603 N10276 N06625 C11000 C44300
Model ER 3100 -Electrical Resistance Probe with Adjustable Length " NPT Pipe Plug Mount and Cylindrical Element
Model ER3100 Electrical Resistance Probe is an adjustable-insertion-length probe with a " NPT compression fitting. The compression fitting allows the probe to be inserted into the process to the required length. The probe requires process isolation or process shutdown to install and a threaded pipe fitting to mount. The all-welded construction allows the probe to be used in harsh environments. The probe assembly consists of an insertion rod with an element, a hermetically sealed connector welded in place, a compression fitting, and a safety nut to prevent blow out. A velocity shield can be added to the assembly if required. Several standard elements and lengths are available to meet your specific needs. (Refer to the Element and Alloy Selection Chart for more information).
Specifications: Probe Body Element Seal Fill Material Temperature Rating Pressure Rating Mounting 316 Stainless Steel Welded Ceramic 500 F/260 C 1500 PSI/102 Bar 0.75 inch NPT Fitting

Model ER3
ER3
Electrical Resistance Adjustable Pipe Plug Probe Pipe Plug Size 2 0.75 inch NPT Pipe Plug 3 1 inch NPT Pipe Plug Probe Body Material 22 316 44 C276 E/R Element Options 500 CT10 Cylindrical - 10 mil thickness (5 mil useful probe life) 600 CT20 Cylindrical - 20 mil thickness (10 mil useful probe life) 700 CT50 Cylindrical - 50 mil thickness (25 mil useful probe life) Length 06 8.58 inches max. insertion length 08 10.58 inches max. insertion length 12 14.58 inches max. insertion length 18 20.58 inches max. insertion length Element Alloy XXX Use Code in Alloy Chart E/R Probe Options 00 No Shield 03 Shield 2 22 500 O8 375 O3 Example of Probe Ordering #
For alloys, sizes, or other special requirements not listed, contact our sales department. Code 375 538 541 186 141 Description C1010 5Cr 1/2Mo 9Cr 1Mo 410 S.S 304 S.S Alloy Chart UNS# Code Description G10100 159 316L S.S K42544 A12 C276 K90941 602 Alloy 625 S41000 419 CDA110 S30400 434 CDA443 UNS# S31603 N10276 N06625 C11000 C44300

Model ER4000 - Electrical Resistance Probe with Packing Gland and Loop Element
Model ER4000 Electrical Resistance Probes are retractable and commonly used in high pressure and high temperature applications. A specially designed packing gland is used with the probe for insertion into or retraction from a pressurized system without a process shutdown. The probe is designed to mount onto a 1" piping system, but can easily be adapted to fit your specific requirements. The probe assembly consists of an insertion rod with an element, a hermetically sealed connector welded in place, and a packing gland. A safety cable and safety nut, are also provided to prevent blowout. A velocity shield can be added to the assembly if required. Standard packing material in the packing gland is Teflon, however, graphoil packing can be provided for high temperature applications. Several standard elements and lengths are available to meet your specific needs. (Refer to the Element and Alloy Selection Chart for more information).
Specifications: Probe Body Element Seal Fill Material Temperature Rating Pressure Rating Mounting 316 Stainless Steel Glass or Teflon Ceramic 500 F/260 C 1000 PSI/68 Bar 1 inch Full Port Valve (Min)
STD. LENGTH 18" 24" 30" 36" 42"
I.L. (max) 10.22" 16.22" 22.22" 28.22" 34.22"
Metal Samples Easy Tool is recommended for probe insertion or retraction in systems with pressure over 150 pounds.

Model ER45 ER00
ER45
Electrical Resistance 1 inch Female NPT Probe with Packing Gland Electrical Resistance Replacement Insertion Rod Probe Body Material 2 316 4 C276 Packing Gland Material 0 N/A (replacement insertion rod) 2 316 4 C276 E/R Element Options 00 WR40 Wire Loop - 40 mil thickness (10 mil useful probe life) 10 WR80 Wire Loop - 80 mil thickness (20 mil useful probe life) 20 TU04 Tube Loop - 4 mil thickness (2 mil useful probe life) 30 TU08 Tube Loop - 8 mil thickness (4 mil useful probe life) 40 TU16 Tube Loop - 16 mil thickness (8 mil useful probe life) 80 SL04 Strip Loop - 4 mil thickness (1 mil useful probe life) 90 SL08 Strip Loop - 8 mil thickness (2 mil useful probe life) Seal Type 1 glass 2 Teflon 3 Epoxy Length 18 11.60 inches max. insertion length 24 17.60 inches max. insertion length 30 23.60 inches max. insertion length 36 29.60 inches max. insertion length 42 35.60 inches max. insertion length Element Alloy XXX Use Code in Alloy Chart E/R Probe Options 00 No Shield 01 Shield, Coupon adapter (118), hardware 02 Shield, Coupon adapter (220), hardware 03 Shield 2 2 10 1 36 375 O2 Example of Probe Ordering # For alloys, sizes, or other special requirements not listed, contact our sales department. Safety clamp must be ordered separately.
Code 375 538 541 186 141
Description C1010 5Cr Mo 9Cr 1Mo 410 S.S 304 S.S
Alloy Chart UNS# Code G10100 159 K42544 A12 K90941 602 S41000 419 S30400 434
Description 316L S.S C276 Alloy 625 CDA110 CDA443
UNS# S31603 N10276 N06625 C11000 C44300

Models ER 4100 and 4100 HT - Electrical Resistance Probe with Packing Gland and Cylindrical Element
Model ER4100 Electrical Resistance Probes are retractable and commonly used in high pressure and high temperature applications. The all-welded design allows the probe to be used in harsh environments. A specially designed packing gland is used with the probe for insertion into or retraction from a pressurized system without a process shutdown. The probe is designed to mount onto a 1" piping system, but can easily be adapted to fit your specific requirements. The probe assembly consists of an insertion rod with an element, a hermetically sealed connector welded in place, and a packing gland. A safety cable and safety nut, are also provided to prevent blowout. A velocity shield can be added to the assembly if required. Standard packing material in the packing gland is Teflon, however, graphoil packing can be provided for high temperature applications. Several standard elements and lengths are available to meet your specific needs. (Refer to the Element and Alloy Selection Chart for more information).
Specifications: Probe Body Element Seal Fill Material Temperature Rating Pressure Rating Mounting 316 Stainless Steel Welded Ceramic 500 F/260 C. 1200 F/649 C.HT 1000psi/Bar 1 inch Full Port Valve (Min) STD. LENGTH 18 24 30 36 42 I.L (max) 14.85 20.85 26.85 32.85 38.85

ER4100/ER4100HT ORDERING INFORMATION
Model ER45 Electrical Resistance 1 inch Female NPT Probe with Packing Gland ER75 Electrical Resistance 1 inch NPT Probe with Packing Gland, High Temperature ER00 Electrical Resistance Replacement Insertion Rod ER05 Electrical Resistance Replacement Insertion Rod, High Temperature Probe Body Material 2 316 4 C276 Packing Gland Material 0 N/A (replacement insertion rod) 2 316 4 C276 E/R Element Options 500 CT10 Cylindrical - 10 mil thickness (5 mil useful probe life) 600 CT20 Cylindrical - 20 mil thickness (10 mil useful probe life) 700 CT50 Cylindrical - 50 mil thickness (25 mil useful probe life) Length 18 14.85 inches max. insertion length 24 20.85 inches max. insertion length 30 26.85 inches max. insertion length 36 32.85 inches max. insertion length 42 38.85 inches max. insertion length Element Alloy XXX Use Code in Alloy Chart E/R Probe Options 00 No Shield 01 Shield, Coupon adapter (118), hardware 02 Shield, Coupon adapter (220), hardware 03 Shield ER3 2 2 700 36 375 O2 Example of Probe Ordering #
For alloys, sizes, or other special requirements not listed, contact our sales department. Safety clamp must be ordered separately.
Code 375 538 541 186 141 Description C1010 5Cr 1/2Mo 9Cr 1Mo 410 S.S 304 S.S Alloy Chart UNS# Code Description G10100 159 316L S.S K42544 A12 C276 K90941 602 Alloy 625 S41000 419 CDA110 S30400 434 CDA443 UNS# S31603 N10276 N06625 C11000 C44300

Model ER4200 - Electrical Resistance Probe with Packing Gland and Small Flush Element
Model ER4200 is a retractable, flush-mount, electrical resistance probe ideally suited for applications where the probe element needs to be flush with the wall of the pipe. A specially designed packing gland is used with the probe for insertion to or retraction from a pressurised system without a process shutdown. Standard packing material in the packing gland is Teflon, however, graphoil packing can be provided for high temperature applications. The probe is designed to mount into a 1" piping system, but can easily be adapted to fit your specific requirements. The probe consists of an insertion rod with an element, a hermetically sealed connector welded in place and a packing gland. The insertion length (I.L.) is calculated to the end of the element. Probe length can be specified by the customer. For standard probes, the maximum length is given in the chart below. Several standard elements are available to meet your specific needs. (Refer to the Element and Alloy Selection Chart for more information).
Specifications: Probe Body Element Seal Fill Material Temperature Rating Pressure Rating Mounting 316 Stainless Steel Glass or Teflon Epoxy 500 F/260 C. - Teflon 1200 F/649 C. - Graphoil 150psi/102 Bar 1 inch Full Port Valve (Min)
STD. LENGTH 18" 24" 30" 36" 42"
I.L (max) 10.22 16.22 22.22 28.22 34.22

Model ER45 Electrical Resistance 1 inch Female NPT Probe with Packing Gland Probe Body Material 22 316 44 C276 E/R Element Options A0 FS04 Flush Mount - 4 mil thickness (2 mil useful probe life) B0 FS08 Flush Mount - 8 mil thickness (4 mil useful probe life) H0 FS20 Flush Mount - 20 mil thickness (10 mil useful probe life) Seal Type 1 glass 3 Epoxy Length 18 10.22 inches max. insertion length 24 16.22 inches max. insertion length 30 22.22 inches max. insertion length 36 28.22 inches max. insertion length 42 34.22 inches max. insertion length Element Alloy XXX Use Code in Alloy Chart E/R Probe Options 00 ER45 22 A0 1 36 375 0 Example of Probe Ordering #
For alloys, sizes, or other special requirements not listed, contact our sales department. Safety clamp must be ordered separately.

Model ER 6000 - Electrical Resistance Probe with Fixed Length Flange and Loop Element
Model ER6000 is a fixed-insertion-length, flange-mounted, electrical resistance probe. The probe is ideally suited for use in high pressure and/or hazardous applications where threaded fittings are not available or not recommended. Process shutdown or process isolation is required for installation and inspection. The probe assembly consists of an insertion rod with an element, a hermetically sealed connector, a velocity shield, and a flange (as specified by customer), which are all welded in place. A mechanical seal can be added for additional safety. Several standard elements, lengths, and different flange sizes are available to meet your specific needs. (Refer to the Element and Alloy Selection Chart for more information).
Specifications: Probe Body Element Seal Fill Material Temperature Rating Pressure Rating Mounting 316 Stainless Steel Glass or Teflon Ceramic 500 F/260 C According to Flange Rating Mating Flange
STD. LENGTH 8" 12" 18" 24"

Model ER6 Electrical Resistance Fixed Length Probe with Flange Flange Size 1 1 inch Flange 2 1.5 inch Flange 3 2 inch Flange 4 3 inch Flange 5 4 inch Flange 6 0.5 inch Flange 7 6 inch Flange Probe Body Material 22 316 44 C276 E/R Element Options 0 WR40 Wire Loop - 40 mil thickness (10 mil useful probe life) 1 WR80 Wire Loop - 80 mil thickness (20 mil useful probe life) 2 TU04 Tube Loop - 4 mil thickness (2 mil useful probe life) 3 TU08 Tube Loop - 8 mil thickness (4 mil useful probe life) 4 TU16 Tube Loop - 16 mil thickness (8 mil useful probe life) 8 SL04 Strip Loop - 4 mil thickness (1 mil useful probe life) 9 SL08 Strip Loop - 8 mil thickness (2 mil useful probe life) Flange Pressure Rating 1 150 lb. 2 300 lb. 3 600 lb. 4 1200 lb. 5 1500 lb. 6 900 lb. Seal Type 1 Glass 2 Teflon 3 Epoxy Length 08 7.33 inches max. insertion length 12 11.33 inches max. insertion length 18 17.33 inches max. insertion length 24 23.33 inches max. insertion length Element Alloy XXX Use Code in Alloy Chart E/R Probe Options 00 No Shield 01 Shield, coupon adapter (118), hardware 02 Shield, coupon adapter (220), hardware 03 Shield ER6 2 22 4 1 2 O8 375 O3 Example of Probe Ordering #
SCROLL DOWN FOR THIRD PAGE

ER6000 ORDERING INFORMATION CONTINUED
Code 375 538 541 186 141
Description C1010 5Cr Mo 9Cr 1Mo 410 S.S 304 S.S
Alloy Chart UNS# Code G10100 159 K42544 A12 K90941 602 S41000 419 S30400 434
Description 316L S.S C276 Alloy 625 CDA110 CDA443
UNS# S31603 N10276 N06625 C11000 C44300

Model ER 6100 - Electrical Resistance Probe with Fixed Length Flange and Cylindrical Element
Model ER6100 is a fixed-insertion-length, flange-mounted, electrical resistance probe. The probe is ideally suited for use in high pressure and/or hazardous applications where threaded fittings are not available or not recommended. Process shutdown or process isolation is required to install and inspect. The all-welded construction allows the probe to be used in harsh environments. The probe assembly consists of an insertion rod with an element, a hermetically sealed connector, and a flange (as specified by customer), which are all welded in place. A mechanical seal can be added for additional safety. Several standard elements, lengths, and different flange sizes are available to meet your specific needs. (Refer to the Element and Alloy Selection Chart for more information).
Specifications: Probe Body Element Seal Fill Material Temperature Rating Pressure Rating Mounting 316 Stainless Steel Welded Ceramic 500 F/260 C According to Flange Rating Mating Flange
STD. LENGTH 8" 12" 18" 24"

Model ER6 Electrical Resistance Fixed Length Probe with Flange Flange Size 1 1 inch Flange 2 1.5 inch Flange 3 2 inch Flange 4 3 inch Flange 5 4 inch Flange 6 0.5 inch Flange 7 6 inch Flange Probe Body Material 22 316 44 C276 E/R Element Options 5 CT10 Cylindrical - 10 mil thickness (5 mil useful probe life) 6 CT20 Cylindrical - 20 mil thickness (10 mil useful probe life) 7 CT50 Cylindrical - 50 mil thickness (25 mil useful probe life) Flange Pressure Rating 10 150 lb. 20 300 lb. 30 600 lb. 40 1200 lb. 50 1500 lb. 60 900 lb. Length 08 10.58 inches max. insertion length 12 14.58 inches max. insertion length 18 20.58 inches max. insertion length 24 26.58 inches max. insertion length Element Alloy XXX Use Code in Alloy Chart E/R Probe Options 00 No Shield 01 Shield, coupon adapter (118), hardware 02 Shield, coupon adapter (220), hardware 03 Shield ER6 2 22 7 20 O8 375 O3 Example of Probe Ordering #

Model ER 6104 - Electrical Resistance Probe with Packing Gland Flange and Cylindrical Element
Model ER6104 is a retractable length, flange-mounted, electrical resistance probe. The probe is ideally suited for use in high pressure and/or hazardous applications where threaded fittings are not available. A specially designed packing gland is used with the probe for insertion into or retraction from a pressurised system without a process shutdown. The probe is designed to mount onto a 1" piping system, but can easily be adapted to fit your specific requirements. The probe assembly consists of an insertion rod with an element, a hermetically sealed connector welded in place, and a packing gland. A safety cable and safety nut, are also provided to prevent blowout. A velocity shield can be added to the assembly if required. Standard packing material in the packing gland is Teflon, however, graphoil packing can be provided for high temperature applications. Several standard elements and lengths are available to meet your specific needs. (Refer to the Element and Alloy Selection Chart for more information).
Specifications: Probe Body Element Seal Fill Material Temperature Rating Pressure Rating Mounting 316 Stainless Steel Welded Ceramic 500 F/260 C According to Flange Rating Mating Flange
STD. LENGTH 18" 24" 30" 36"

Model ER6 Electrical Resistance Fixed Length Probe with Flange with Packing Gland Flange Size 1 1 inch Flange 2 1.5 inch Flange 3 2 inch Flange 4 3 inch Flange 5 4 inch Flange 6 0.5 inch Flange 7 6 inch Flange Probe Body Material 22 316 44 C276 E/R Element Options 5 CT10 Cylindrical - 10 mil thickness (5 mil useful probe life) 6 CT20 Cylindrical - 20 mil thickness (10 mil useful probe life) 7 CT50 Cylindrical - 50 mil thickness (25 mil useful probe life) Flange Pressure Rating 10 150 lb. 20 300 lb. 30 600 lb. 40 1200 lb. 50 1500 lb. 60 900 lb. Length 18 14.85 inches max. insertion length 24 20.85 inches max. insertion length 30 26.85 inches max. insertion length 36 32.85 inches max. insertion length Element Alloy XXX Use Code in Alloy Chart E/R Probe Options 00 No Shield 01 Shield, coupon adapter (118), hardware 02 Shield, coupon adapter (220), hardware 03 Shield ER6 2 22 7 20 O8 375 O3 Example of Probe Ordering #

Model ER 7000 - Electrical Resistance Probe for the 2 inch Access System with Loop Element
Model ER7000 Electrical Resistance Probe is a fixed-length probe for use with the 2" access systems at high pressure and temperatures. The probe assembly consists of an insertion rod with an element, a hermetically sealed connector, a hollow plug nut, and a velocity shield, which are all welded in place. The hollow plug nut on the probe screws into the hollow plug of the access system. This allows the probe to be installed in the process, using a retriever tool and service valve, without process shutdown. Several standard element and probe lengths are available to meet your specific needs. Probe adaptors are available and must be ordered separately. (Refer to the Element and Alloy Selection Chart for more information).
Specifications: Probe Body Element Seal Fill Material Temperature Rating Pressure Rating Mounting 316 Stainless Steel Glass or Teflon Ceramic 500 F / 260 C 3600 PSI/245 Bar 2 inch Access System with Hollow Plug

Model HR Electrical Resistance Probe for High Pressure (HPTM and MHTM) Access Systems Mounting Material 2 316 3 C276 Connector Type 1 Small Connector 2 Standard Connector E/R Element Options 0 WR40 Wire Loop - 40 mil thickness (10 mil useful probe life) 1 WR80 Wire Loop - 80 mil thickness (20 mil useful probe life) 2 TU04 Tube Loop - 4 mil thickness (2 mil useful probe life) 3 TU08 Tube Loop - 8 mil thickness (8 mil useful probe life) 4 TU16 Tube Loop - 16 mil thickness (8 mil useful probe life) Seal Type 1 Glass 2 Teflon 3 Epoxy Length XXXX Length in inches, stated in 2 decimal place format (Ex:7.25 inches=0725) Element Alloy XXX Use Code in Alloy Chart E/R Probe Options 00 No Shield 01 Standard Shield 02 Hi-velocity Shield 03 Coupon Holding Shield HR 2 2 4 1 O725 375 O3 Example of Probe Ordering #
Code 375 538 541 186 141 Description C1010 5Cr Mo 9Cr 1Mo 410 S.S 304 S.S Alloy Chart UNS# Code G10100 159 K42544 A12 K90941 602 S41000 419 S30400 434 Description 316L S.S C276 Alloy 625 CDA110 CDA443 UNS# S31603 N10276 N06625 C11000 C44300

Model ER 7100 - Electrical Resistance Probe for the 2 inch Access System with Cylindrical Element
Model ER7100 Electrical Resistance Probe is a fixed-length probe for use with the 2" access system in high pressure and high temperature applications. The all-welded construction of the element makes it ideal for harsh environments. The probe assembly consists of an insertion rod with an element, a hermetically sealed connector, and a hollow plug nut, which are all welded in place. A velocity shield can be added to the assembly if required. The hollow plug nut on the probe screws into the hollow plug of the access system. This allows the probe to be installed in the process, using a retriever tool and service valve, without process shutdown. Several standard elements and probe lengths are available to meet your specific needs. Probe adaptors are available and must be ordered separately. (Refer to the Element and Alloy Selection Chart for more information).
Specifications: Probe Body Element Seal Fill Material Temperature Rating Pressure Rating Mounting 316 Stainless Steel Welded Ceramic 500 F/260 C 3600psi/245 Bar 2 inch Access System with Hollow Plug

Model HR Electrical Resistance Probe for High Pressure (HPTM and MHTM) Access Systems Mounting Material 2 316 3 C276 4 Duplex 2205 Connector Type 1 Small Connector 2 Standard Connector E/R Element Options 50 CT10 Cylindrical - 10 mil thickness (5 mil useful probe life) 60 CT20 Cylindrical - 20 mil thickness (10 mil useful probe life) 70 CT50 Cylindrical - 50 mil thickness (25 mil useful probe life) JO CT 10 Cylindrical (2) - 10 mil thickness (5 mil useful probe life) Length XXXX Length in inches, stated in 2 decimal place format (Ex:6.25 inches = 0625) Element Alloy XXX Use Code in Alloy Chart E/R Probe Options 00 No Shield 01 Standard Shield 02 Hi-velocity Shield 03 Coupon Holding Shield HR 2 2 60 O725 375 O3 Example of Probe Ordering #

Model ER 7200 - Electrical Resistance Probe for the 2 inch Access System with Flush Element
Model ER7200 Flush-Mount, Electrical Resistance Probe is a fixed-length probe for use with the 2" access system in high pressure and high temperature applications. These probes are ideally suited for applications where the probe element needs to be flush with the wall of the pipe. The probe assembly consists of an insertion rod with an element, a hermetically sealed connector, and a hollow plug nut, which are all welded in place. The hollow plug nut on the probe screws into the hollow plug of the access system. This allows the probe to be installed in the process, using a retriever tool and service valve, without process shutdown. Insertion lengths range from 1.25" to 36" in 1/16" increments. Several standard elements are available to meet your specific needs. Probe adaptors are available and must be ordered separately. (Refer to the Element and Alloy Selection Chart for more information).
Specifications: Probe Body Element Seal Fill Material Temperature Rating Pressure Rating Mounting 316 Stainless Steel Glass or Epoxy Epoxy 500 F/260 C 3600psi/245 Bar 2 inch Access System

Model HR Electrical Resistance Probe for High Pressure (HPTM and MHTM) Access Systems Mounting Material 2 316 3 C276 Connector Type 1 Small Connector 2 Standard Connector E/R Element Options A S4 Flush Mount - 4 mil thickness (2 mil useful probe life) B S8 Flush Mount - 8 mil thickness (4 mil useful probe life) H S20 Flush Mount - 20 mil thickness (10 mil useful probe life) Seal Type 1 Glass 3 Epoxy Length Length in inches, stated in 2 decimal place format (Ex:7.25 inches = XXXX 0725) Element Alloy XXX Use Code in Alloy Chart E/R Probe Options 0 No Shield HR 2 2 B 3 O725 375 OO Example of Probe Ordering #

Model ER 7210 - Electrical Resistance Probe for the 2 inch Access System with Large Flush Element
Model ER7210 Flush-Mount Electrical Resistance Probe is a fixed-length probe for use with the 2" access system in high pressure and high temperature applications. These probes are ideally suited for applications where the probe element needs to be flush with the wall of the pipe. The probe assembly consists of an insertion rod with an element, a hermetically sealed connector, and a hollow plug nut, which are all welded in place. The hollow plug nut on the probe screws into the hollow plug of the access system. This allows the probe to be installed in the process, using a retriever tool and service valve, without process shutdown. Insertion lengths range from 1.25" to 36" in 1/16" increments. Several standard elements are available to meet your specific needs. Probe adaptors are available and must be ordered separately. (Refer to the Element and Alloy Selection Chart for more information).
Specifications: Probe Body Element Seal Fill Material Temperature Rating Pressure Rating Mounting 316 Stainless Steel Epoxy Epoxy 500 F/260 C 3600psi/245 Bar 2 inch Access System

Model HR Electrical Resistance Probe for use with MS3600 2 inch Access Systems Mounting Material 2 316 3 C276 4 Alloy 625 5 Duplex 6 Super Duplex Connector Type 1 Small Connector 2 Standard Connector E/R Element Options C3 S05 Flush Mount - 5 mil thickness (2.5 mil useful probe life) D3 S10 Flush Mount - 10 mil thickness (5 mil useful probe life) E3 S20 Flush Mount - 20 mil thickness (10 mil useful probe life) F3 S40 Flush Mount - 40 mil thickness (20 mil useful probe life) Length XXXX Length in inches, stated in 2 decimal place format (Ex:7.25 inches=0725) Element Alloy XXX Use Code in Alloy Chart E/R Probe Options 0 No Shield HR 2 2 C3 O725 375 OO Example of Probe Ordering #

Model ER 7220 - Electrical Resistance Probe for the 2 inch Access System with Large Flush Element
Model ER7220 Flush-Mount Electrical Resistance Probe is an adjustable-length probe for use with the 2" access system in high pressure and high temperature applications. These probes are ideally suited for applications where the probe element needs to be flush with the wall of the pipe. The probe assembly consists of an insertion rod with an element, a hermetically sealed connector, and a hollow plug nut, which are all welded in place. The hollow plug nut on the probe screws into the hollow plug of the access system. This allows the probe to be installed in the process, using a retriever tool and service valve, without process shutdown. Insertion lengths range from 1.687" up to 36" in 1/16" increments. Several standard elements are available to meet your specific needs. Probe adaptors are available and must be ordered separately. (Refer to the Element and Alloy Selection Chart for more information).
Specifications: Probe Body Element Seal Fill Material Temperature Rating Pressure Rating Mounting 316 Stainless Steel Epoxy Epoxy 500 F / 260 C 6049psi/420 Bar 2 inch Access System

Model HR Electrical Resistance Probe for High Pressure (HPTM and MHTM) Access Systems Mounting Material 2 316 3 C276 Connector Type 1 Small Connector 2 Standard Connector E/R Element Options C3 S05 Flush Mount - 5 mil thickness (2.5 mil useful probe life) D3 S10 Flush Mount - 10 mil thickness (5 mil useful probe life) E3 S20 Flush Mount - 20 mil thickness (10 mil useful probe life) F3 S40 Flush Mount - 40 mil thickness (20 mil useful probe life) Length XXXX Length in inches, stated in 2 decimal place format (Ex:7.25 inches=0725) Element Alloy XXX Use Code in Alloy Chart E/R Probe Options AD No Shield, Adjustable HR 2 2 C3 725 375 AD Example of Probe Ordering #
Code 375 538 541 186 141 Description C1010 5Cr Mo 9Cr 1Mo 410 S.S 304 S.S Alloy Chart UNS# Code Description G10100 159 316L S.S K42544 A12 C276 K90941 602 Alloy 625 S41000 419 CDA110 S30400 434 CDA443 UNS# S31603 N10276 N06625 C11000 C44300

Model ER 7300 - Electrical Resistance Probe, Retrievable Spiral Loop for Two Inch High Pressure Access Systems
Model ER7300 spiral loop probe is retrievable, electrical resistance probe designed for use with two inch high pressure access systems. The element is a spiral wound strip encased in epoxy. This approach to element construction offers several advantages over other element geometries:

High intrinsic resistance - provides highly stable readings with low susceptibility to noise. High element strength - allows use in very high flow rate regimes such as a gas transmission. Wide spacing of element loops - minimizes the risk of iron sulphide scaling and bridging.
While the spiral loop probe is ideally suited to fast flowing, sour systems, its high stability makes it a suitable choice for oil and gas systems. Insertion length (I.L.) is specified by the customer, using the formula: I.L. = PD + WT + 1.75" (where PD = penetration depth, WT = wall thickness) Note: Formula valid for access fitting heights of 5.25" (HP) and 5.5 (MH)
Specifications: Probe Body Element Seal Element Material Temperature Rating Pressure Rating 316L Stainless Steel Epoxy AISI 1018 250 F/121 C 3600psi/245 Bar

Model HR Electrical Resistance Probe for High Pressure (HPTM and MHTM Access Systems Mounting Material and Connector Type 22 316 stainless steel with standard connector E/R Element Options K SP10 Spiral Loop - 10 mil thickness (5 mil useful probe life) L SP20 Spiral Loop - 20 mil thickness (10 mil useful probe life) Seal Type 3 Epoxy Length XXXX Length in inches, stated in 2 decimal place format (Ex:7.25 inches=0725) Element Alloy XXX Use Code in Alloy Chart E/R Probe Options 00 No Shield HR 22 K 3 725 375 OO Example of Probe Ordering #

EASY TOOL RETRACTING SYSTEMS
TheEasy Tool Retracting System is used for inserting and retracting probes and coupon holder assemblies in pressure applications. Metal Samples Easy Tool is strongly recommended for systems with pressure over 150 pounds. The tool's design enables easy insertion to any depth you require. The Easy Tool weighs under 15 pounds and is available in 32" and 44" sizes. The tool is one of the lightest, shortest retracting tools available on the market. Easy Tool can be used with most packing glands available in the industry.

MODEL 600
The Rose Model 600 Access Valve Assemblies are designed to allow access to pressurised areas without process shutdown. The assembly consists of a Thredolet, all thread nipple, ball valve and a 5" Packing Gland interjoint nipple. NOTE: The 5" nipple is used as standard, and is suitable for all probe elements except coupon holding shields which require a 9" nipple. The full port valve is provided in either carbon steel or 316 Stainless Steel body, with Polyfill seats and Viton body seals. All items comply with NACE standard MR0175, for materials resistant to sulfide stress cracking. Flanged Outlets to connect with a pipeline or vessel mating flange are available. The Model 600 Access Valve Assembly accommodates all ROSE retractable probes. This includes Electrical Resistance, Linear Polarisation Resistance, Coupon Holder, Injection Tubes and Nozzles, Hydrogen, Sand and Galvanic Probes. ORDERING INFORMATION Thredolet Outlet/ C.S. Access Valve with St St Trim - P.N. 700990
SYSTEM ACCESSORIES CABLES Factory Assembled: For Portable Instrument Series P.N 700716 + Length For Transmitter and Data Collection Systems P.N. 700726 + Length Cable - Heavy Duty: P.N 700331 Two wire for transmitter P.N. 700431 Connectors: Low Pressure Probe Type A P.N. 700521 2" System High Pressure Type B P.N. 700343 Probe to Cable Adaptor for 2" High Pressure System Portable with Standard 6 pin Connector P.N. 700319 Portable with Small 6pin ConnectorFixed P.N. 700033 Fixed Adapter with Standard 6 pin Connector P.N. 700640 Fixed Adaptor with Small 6pin Connector P.N. 700077 Shield Options Standard Shield - Wire Loop Probe - P.N. 700608 High Velocity Shield - Wire Loop Probe - P.N. 700609 Standard Shield - Cylindrical Probe - P.N. 700610 High Velocity Shield - Cylindrical Probe - P.N. 700611 Coupon Holder Shield - Wire Loop Probe - P.N. 700612 Coupon Holder Shield - Cylindrical Probe - P.N. 700613 SAFETY CLAMPS For 18" and 24" Probe lengths P.N. 700700 For 30", 36" and 42" Probe lengths P.N. 700701

MS1500L
TheMS1500L is a hand-held, battery-powered corrosion meter used with linear polarisation resistance (LPR) and galvanic probes provide both measurements and data collection. The unit is lightweight so that it can be easily carried to any location where measuring or data collecting is required. MEASUREMENT Measurement functions of the unit include:

Corrosion rate for 2-electrode LPR probe Corrosion rate for 3-electrode LPR probe "Pitting Index" Zero Resistance Ammetry Electrode Potential
Using galvanic probes with an appropriate combination of corroding, redox and reference electrodes, the can measure the corrosion potential of a corroding electrode, or the redox potential of the process fluid, witch provides a wide range of information on such phenomena as active/passive transitions, inhibitor film persistency, inhibitor mechanisms, cathodic protection criteria, as well as providing an alternative means to
BACK TO LINEAR POLARISATION MENU
measure the onset of pitting attacks, crevice attacks, and conjoint action failure phenomena (stress cracking). DATA COLLECTION A total of 3000 readings can be stored in the MS1500s onboard memory that will hold readings from up to 100 individual probes. Stored data may be called to the instrument screen and reviewed at any time. Backup batteries will hold all data stored in the memory for up to 12 months, in the event of failure of the main instrument batteries. Data may be selectively deleted from the memory to accommodate additional information once the 3000 reading capacity is reached. Alternatively, information my be downloaded to an IBM compatible PC as a comma delimited ASCII file for import into any of the standard data handling and analysis programs (e.g., EXCEL , LOTUS 123 , Quattro Pro ). The MS1500L may also be used as a data collection and transfer terminal for the MS3500L remote data logger. Accumulated data from several MS3500L field-based units may be locally downloaded to the MS1500L hand-held terminal and then transferred to an IBM compatible PC for further analysis.

TECHNICAL SPECIFICATIONS
Functions:
Corrosion Rate (MPY): Three electrode measurement Corrosion Rate (MPY): Two electrode measurement Galvanic Current ( m A) - ZRA Potential (mV) 0 - 200 mpy 0 - 200 mA 1000 mV Corrosion Rate - 0.01 mpy Metal Loss - 0.01 mils Probe Life - 1 unit 12 key membrane keypad 3000 readings; screen reviewable using scroll feature RS232 serial port 4-line x 20 character LCD dot matrix
Range:
Resolution: Control: Memory Capacity: Communication Link: Display:
Memory Protection: 10-year battery, back-up life Dimensions: Weight: Power: Part#: 7.63 inches (h) x 4.15 inches (w) x 2.00 inches (d) 194 mm (h) x 105 mm (w) x 50 mm (d) 1.5 lbs. (5.2 lbs. With hardshell case) Three 1.5V, AA batteries IN1500L Class 1, Division 1 Groups A,B,C and D Temperature Code T2D Class I, Zone 0 Group IIC, T2D Conforms to ANSI UL Std. 913
Intrinsic Safety:

MS 2500L
TheMS2500Lis a micro-processor controlled transmitter that features transmission through a two-wire 4-20mA current loop. The unit is designed to provide continuous on-line corrosion rate measurements using the 3 Electrode Technique. The MS2500L is encased in a compact, UL-approved, explosion and weather proof NEMA enclosure. Operating temperatures range from 32F to 158F. If intrinsic safety is required, the unit can be powered by an isolated repeater power source. Circuit board switches determine operation mode options, which include: Excitation Polarity: anodic or cathodic Cyclic Time: 1-99 minutes
Transmitter Data Type: Corrosion rate (mpy) or Electrode potential (mv)(br) Installation costs are less with the MS2500L because all field wiring is the two-wire type. This eliminates the need for running special signal cables. (Note: The instrument is supplied with a 10-foot instrument-to-probe extension cable with connector). Data from the MS2500L can be displayed on a suitable recorder, digital voltmeter, or the MS2510 Receiver. For convenience, the MS2510 has an auxiliary power supply and a current loop output for passing data to another readout device.

Probe Type: Potentiostatic Probe Excitation: Allowable Ref-Test Potential for LPR Measurement: Cycle Time Adjustment: Corrosion Potential Measurement: Accuracy @ 25 C: Weight: Power Requirements: Transmitter Type:
Three-electrode LPR 10mV 200mV 1-99 minutes 1 V LPR Mode: 0.2% Full Scale, Potential Mode: 5 millivolts 4 lbs. (1.8 kg) 11 to 35 Volts DC 2-wire, 4-20mA 4 - 20mA representing: 0 - 100 mils per year 0 to 1 volt potential 0 to -1 volt potential 32F to 158 F (0 C to 70 C) 0.8 microamps/Deg. C Explosion Proof (FM, CSA, CENELEC, UL) Class I, Groups B, C, D, Class II, Groups E, F, G, Class III, CENELEC: Eexd IIC NEMA 4X, 7BCD, 9EFG Mounting hardware is supplied with the unit. It may be mounted up to 10 feet from the probe location to a flat surface or pipe. 4-wire with shield (light armour), 10 feet Designed to be intrinsically safe in Zone 1, Group IIB hazardous areas with the use of 4-20mA, isolated, repeater power supplies. IN2500L
Output Signals:
Operating Temperature: Temperature Stability:
Enclosure:
Mounting Requirements: Cable: Intrinsic Safety: Part#:

MS 3500L
TheMS3500L Remote Data Logger is designed to provide a continuous record of corrosion activity in remote locations that are infrequently visited, such as crosscountry pipelines and unmanned production platforms. However, this unit finds equal application in locations that are inconvenient or difficult to access on a regular basis. The MS3500L is completely self-contained with the onboard battery system supplying the total power requirement for operation. The unit is extremely versatile, having a variety of menu selectable measurement modes:

Corrosion rate for 2-electrode LP probe Corrosion rate for 3-electrode LP probe "Pitting Index" for 2-electrode probe Galvanic current - Zero Resistance Ammetry Electrode Potential
Once in place, this unit will automatically read the probe at customer-selected intervals and store the resulting data in the units onboard memory. The onboard memory will collect up to 3000 data points before data download is required. The data collection interval is programmable in hour intervals. At a data collection interval of 1 hour, data downloading need only be performed every ninety days. With longer data collection intervals (8-12 hours), the unit may be unattended for as long as 6-8 months between downloading operation. An optical, infrared, RS232 communication link is provided for data download to
either a laptop (IBM compatible) PC, or to the MS1500L portable data logger. Downloaded data may be analysed, reviewed, or reported by conventional spreadsheet, database, or mathematical software packages. The infrared communication link is an integral part of the intrinsically safe design on the unit. Optical, instead of electrical, this unique feature permits data downloading without removing the instrument or "memory module" form the hazardous area. Another unique feature of the MS3500L is the high level of onboard intelligence. The two-line, 20-character LCD screen allows visual review of all historical data in memory and reads directly as corrosion rate, millivolts or microamps. The LCD screen, together with the 2-key membrane key pad provides a user-friendly, interactive, prompting system that is used for both system setup and data review. This makes the MS3500L the most advanced unit of its type on the market. An optional feature of the unit is the addition of a 4-20mA continuous output transmitter. This allows transmission of data, via a 4-20mA loop, to a plant computer or central data logger for integration with other real-time process parameters. This data transmission can be accomplished without disruption of the units basic logging and data storage operations. The 4-20mA loop extends the capabilities of the unit to include conventional, in-plant, real-time data communication. The unit uses a NEMA 4X (IP-65) enclosure, making it suitable for use in the most extreme of outdoor conditions. The inclusion of the potential and galvanic current as measurement model makes the unit a complete diagnostic tool for studying electrochemical corrosion. Not only can general corrosion rates be measured but, in addition, such phenomena as activepassive transitions, onset of pitting and crevice corrosion, bimetallic attack, and oxygen ingress can be monitored.
Technical Specifications Corrosion rate (MPY): Three-electrode measurement Corrosion rate (MPY): Two-electrode measurement Galvanic Current ( m A) - ZRA Potential (mV) 0 - 200mpy 0 - 200mA 1000mV 0.1% of full scale Two-key membrane keypad 3000 readings; screen reviewable using scroll feature Programmable, hourly increments (1 - 1000) Infrared, RS232, 4-20mA (optional) 11.50 inches (h) x 8.95 inches (w) x 4.00 inches (d) 292 mm (h) x 227 mm (w) x 102 mm (d) (NEMA 4X) Six 1.5V AA Dry Cell Batteries 11.94lbs (5.42kg) IN3500L (Remote LPR Data Logger) IN3510L (Remote LPR Data Logger with 4-20mA output transmitter) Class 1. Division 1 Groups A, B, C and D Temperature Code T3 Class I, Zone 0 Group IIC, T3 Conforms to ANSI UL Std. 913
Functions:
Range: Resolution: Control: Memory Capacity: Reading Interval: Communication Link: Enclosure: Power: Weight: Part#:
Intrinsic Safety:
S 1000 Corrosion Monitor
Description The MS1000 is a hand-held, battery-powered corrosion meter. This versatile instrument measures the instantaneous corrosion rate and the electrochemical current noise (ECN) between electrodes in the short-circuited condition. The instrument can analyse any two-electrode linear polarisation resistance (LPR) type probe. Corrosion Rate Instantaneous corrosion rate measurements are made with linear polarisation resistance (LPR) technique. This instrument has been designed to calculate the corrosion rate of carbon steel and common grades of stainless steel in mils per year. Multiplication factors for copper, admiralty brass, and lead have been included on the front panel. The instrument has also been programmed to calculate the corrosion rate based on using electrodes with surface areas of 5 cm2. Multiplication factors may be used for electrodes with different surface areas. Electrochemical Current Noise (ECN) A high precision zero resistance ammeter is used for monitoring the electrochemical current noise between electrodes. The current is displayed in microamps. The magnitude of the ECN may be used as qualitative indication of the occurrence of localized corrosion such as pitting or microbiological influenced corrosion. The ECN function may also be used to monitor the galvanic current between electrodes of different alloys.

Specifications Range Resolution
LPR Probe Configuration Cylindrical Electrodes Flush Electrodes Electrochemical Current Noise (ECN) Measurement Time: Retractable Cable: Compatible Probe Types: Maximum Recommended Distance to Probe: Dimensions: Weight: Operating Temperatures: Storage Temperatures: Battery: 0 to 40mpy 0 to 400mpy 0 to 80mA 0.02mpy 0.2mpy 0.04mA
Corrosion Rate - 60 seconds Electrochemical Current Noise - 30 Seconds 2 inch (61cms) retracted 10 inch (3.05m) extended All existing brands of 2-electrode probes 2000 ft (645 metres) 7.7 inches L x 4.2 inches W x 1.3 inches H 19.6cms L x 10.7cms x 3.3cms H 3 lbs. including carrying case 32 to 122 F (0 to 50 C) -4 to +158 F (-20 to +70 C) One 9 volt rechargeable nickel-cadmium Standard automatic shutdown feature
Hand-held unit Low battery indicator "Beep" user alerts after measurement Sleep mode after 25 seconds conserves power
Features:

S2000 Corrosion Monitor
The S2000 is a microprocessor-based, field-mountable transmitter. Using the linear polarisation resistance technique, the S2000 allows for the rapid determination of corrosion rates in real time. The instrument also incorporates a high precision zero resistance ammeter to measure the electrochemical current noise (ECN) between the electrodes in the short-circuited condition. Electrochemical noise measurements offer excellent potential in the areas of detection and measurement of localised corrosion. The corrosion rate and the ECN are transmitted with 4 - 20mA current loops and RS232 communications. Uses This instrument, when combined with two-electrode corrosion probes, monitors the instantaneous corrosion rate, thus allowing the user to monitor inhibitor effectiveness, identify process upsets, and evaluate corrective actions in real time. The S2000 may be used to optimise the content, level, and dosage of corrosion inhibitors in both the plant and the lab. The instrument may also be used to detect and qualitatively measure localised corrosion events such as pitting or microbiological influenced corrosion. These forms of corrosion contribute very little to the actual mass loss, but could be devastating to the life of the equipment.
Features
Qualitative indication of localised corrosion. Generally, if the electrochemical current noise divided by two is less than the corrosion rate, then pitting may be occurring but the pits will probably be shallow and wide; however, pitting may be a serious concern if this value is greater than the corrosion rate. A low pass filter is included on the input of this instrument to eliminate electromagnetic noise. The electrical signal applied across the probes is electrically isolated from the transmitter power supply, thus eliminating potential ground loops that could influence the measured corrosion rate and ECN. The corrosion transmitter allows the user to set the alloy multiplier on the front panel of the instrument. The alloy multiplier selects a separate subroutine that automatically inputs the necessary values for each alloy type. The instrument is housed in a NEMA-4X enclosure and is mounted on a 4" x 8" mounting pattern.
Technical Specifications Range LPR Probe Configuration Cylindrical Electrodes Flush Electrodes 0 to 40mpy 0 to 400mpy 0.02mpy 0.2mpy Resolution
Zero Resistance Ammeter (ZRA) Dimensions Weight Operating Temperatures Power Maximum Recommended Distance to Probe:
0 to 80A 9.5 inches L x 5 inches H x 6 inches W 4 lbs. 11 oz. 32 to 122 F (0 to 50 C) 120 volts AC 2000ft (645 metres)
0.04A

S 3000 Single Channel linear Polarisation Meter
Corrosion rate is measured in mils per year using industry style two or three electrode flush or standard probes. Twin ranges of 0 - 200 and 0 - 2 mils per year allow for higher resolution with passive probe types such as 304 Stainless Steel. 4-20mA and 0-2v outputs of the corrosion rate are useful for long term monitoring with for instance a y*t recorder. To indicate localised corrosion a localised factor is supplied which is derived from the asymmetry of the current magnitude on reversing the polarity of the polarising potential. In practice this may be misleading and in general if localised corrosion such as pitting is taking place the value of the corrosion rate will be higher than expected and perhaps more variable with respect to time as pits change from active to passive. Greater than one day's battery life on full output enables the instrument to be left logging for long periods without mains supply. A calibration socket is provided on the front panel to test the instrument in service. The LPR Meter is housed in a robust case with carrying handles, mains cable, signal cable, and padded carrying bag. Rose Corrosion Services Limited supplies a one year guarantee on these instruments for parts and labour. Our repair and calibration service takes approximately two days from receipt of goods. Technical Specifications Dimensions (cm) Weight Power Battery 31 x 27 x 10 (W x D x H) 3.1 Kg 220 - 240v AC or as requested One 2.6 AHr Maintenance free lead acid.

S 3002 TWO CHANNEL LPR METER
Used for long term monitoring of corrosion rate on site. Monitoring of two LPR probes simultaneously. Two 4-20mA outputs, one for each channel enables easy connection to a plant control system for on line monitoring of corrosion without need for any computer system. Fixed range 0 - 30 mils per year or as specified. Calibrated for a probe size of 4.5 cm2 or as specified. Mains powered 240v AC or as specified. Simple connection to a two or three electrode probe. No knobs or ranges to set on the front or rear panel of the instrument. Normally housed in a small ABS plastic enclosure with engraved front and rear aluminium panels. However the instrument can be housed on an aluminium chassis plate, an environmental proof enclosure or several of them can be housed in a 19 inch rack, again as specified. Range of instrument is approximately 100 metres or more. Will operate through barrier diodes. Indication of local corrosion if LPR reading varies with time. Very simple to install, integrate and operate. Rose Corrosion supplies a one year guarantee on these instruments for parts and labour. Our repair and calibration service takes approximately two days from receipt of goods. Technical Specifications(cm) Dimensions (cm):31 x 27 x 10 (W x D x H) Weight: Power: 2.1kg 220 - 240v AC or as requested.

S3006 SIX CHANNEL LINEAR POLARISATION METER
Used for long term monitoring of corrosion rate on site. Monitoring of six LPR probes simultaneously. Six 4-20mA outputs, one for each channel enables easy connection to a plant control system for on line monitoring of corrosion without the need for any computer system. Fixed range of 0 - 30 mils per year or as specified. Calibrated for a probe size of 4.5cms2 or as specified. Mains powered 240v AC or as specified. Simple connection to a two or three electrode probe. No knobs or ranges to set on the front or rear panel of the instrument. The LPR Meter is housed in a robust case with carrying handle, mains cable, signal cable, and padded carrying bag. Range of instrument is approximately 100 metres or more. Will operate through barrier diodes. Indication of localised corrosion if LPR leading varies with time. Very simple to install, integrate and operate. RCS supplies a one year guarantee on these instruments for parts and labour. Our repair and calibration service takes approximately two days from receipt of goods. Technical Specifications(cms) Dimensions (cm):31 x 27 x 10 (W x D x H) Weight: Power: 2.1kg 220 - 240v AC or as requested.
Model LP1000 - Linear Polarisation Resistance Probe with NPT Pipe Plug and 2Electrode Endcap
Model LP1000 is a Linear Polarisation Resistance Probe commonly used in Laboratory, bypass-loop, and field applications. The assembly consists of an NPT pipe plug (1 inch, or 1.5 inch or 2 inch), a two-electrode endcap and a six-pin military connector mounted in place. Electrodes are ordered separately. Several standard electrodes are available to meet your specific needs. Specifications: Probe Body Endcap Seal Fill Material Temperature Rating Pressure Rating Mounting 316 Stainless Steel Glass Epoxy 500 F/260 C. 3000psi/204 Bar 1 inch, 1.5 inch, or 2 inch NPT Pipe Plug

LP1000 ORDERING INFORMATION
Model LP13 Linear Polarisation 1 inch NPT Pipe Plug Probe LP16 Linear Polarisation 2 inch NPT Pipe Plug Probe LP17 Linear Polarisation 1.5 inch NPT Pipe Plug Probe Probe Body Material 02 316 03 C.S. 04 C276 LP Electrode Options 20100 Two-electrode integral type with glass seal Options 000 None LP13 02 20100 000 Example of Probe Ordering #
Electrode Part Number - EL400XXX2800000 (XXX-use Code in Alloy Chart) LPR probe electrodes are replaceable and sold separately.
Code 377 159 419 434 Alloy Chart Description C1018 316L S.S. CDA110 CDA443 UNS# G10180 S31603 C11000 C44300
For alloys, sizes, or other special requirements not listed, contact our sales department. Note: Not all alloys are available with all element types and seals.
Model LP1100 - Linear Polarisation Resistance Probe with 1 Inch NPT Pipe Plug and 3-Electrode Endcap
Model LP1100 Linear Polarisation Resistance Probe is commonly used in Laboratory, bypass-loop, and field applications. The assembly consists of an insertion rod, a three-electrode endcap a 1 inch pipe plug and a five-pin military connector mounted in place. The minimum probe LENGTH is 0.5 inches. Probes can be ordered up to any length required by the customer in 0.25 inch increments. The insertion length is calculated by adding the electrode length (1.25 inches) to the LENGTH. Electrodes are ordered separately. Several standard electrodes are available to meet your specific needs.
Specifications: Probe Body Endcap Seal Fill Material Temperature Rating Pressure Rating Mounting 316 Stainless Steel Glass Ceramic or Epoxy 500o F/260o C. 3000 PSI/204 Bar 1 inch NPT Pipe Plug

Model LP13 Linear Polarisation 1 inch NPT Pipe Plug Probe LP16 Linear Polarisation 2 inch NPT Pipe Plug Probe LP17 Linear Polarisation 1.5 inch NPT Pipe Plug Probe Probe Body Material 02 316 03 C.S. 04 C276 LP Electrode Options 10 Three-electrode plug type (replaceable mounting studs 30 Three-electrode integral type (non-replaceable mounting studs Seal Type 100 Glass Options 000 None LP13 02 30 100 000 Example of Probe Ordering #
Model LP2000 - Linear Polarisation Resistance Probe Fixed Length with 0.75 Inch NPT Pipe Plug and 2-Electrode Endcap
Model LP2000 Linear Polarisation Resistance Probe is a fixed length probe with a 0.75 inch NPT pipe plug. The probe require process isolation or process shutdown to install and a threaded pipe fitting to mount. The probe assembly consists of an insertion rod with a two electrode endcap a hermatically sealed connector and a 0.75 inch NPT pipe plug which are all welded in place. The insertion length (I.L.) is calculated to the end of the electrode and can be specified by the customer. For the standard probes, the maximum insertion length is given in the chart below. Electrodes are ordered separately. Several standard electrodes are available to meet your specific needs.
Specifications: Probe Body Endcap Seal Fill Material Temperature Rating Pressure Rating Mounting 316 Stainless Steel Glass Ceramic or Epoxy 500 F/260 C. 3000psi/204 Bar 0.75 inch NPT Pipe Plug
STD. LENGTH 6" 8" 12" 18"
I.L. (max) 5.05 7.05 11.05 17.05

Model LP2 Linear Polarisation Fixed Length Pipe Plug Probe Pipe Plug Size 2 0.75 inch NPT 3 1 inch NPT Probe Body Material 22 316 44 C276 LP Electrode Options 20 Two-electrode integral type Seal Type 1 Glass Length 06 5.05 inch max. insertion length 08 7.05 inch max. insertion length 12 11.05 inch max. insertion length 18 17.05 inch max. insertion length Options 000 None LP2 02 22 20 1 08 000 Example of Probe Ordering #
Code 375 419 434 159 Alloy Chart Description C1010 CDA110 CDA443 316L S.S. UNS# G10100 C11000 C44300 S31603

Model LP2100 - Linear Polarisation Resistance Probe Fixed Length with 1 Inch NPT Pipe Plug and 3-Electrode Endcap
Model LP2100 Linear Polarisation Resistance Probe is a fixed length probe with a 1 inch NPT pipe plug. The probe require process isolation or process shutdown to install and a threaded pipe fitting to mount. The probe assembly consists of an insertion rod with a three electrode endcap a 1 NPT pipe plug and a five-pin military connector mounted in place. The insertion length (I.L.) is calculated to the end of the electrode and can be specified by the customer. For the standard probes, the maximum insertion length is given in the chart below. The maximum I.L. is based on the length of a carbon steel electrode. Electrode lengths may vary depending on the alloy Electrodes are ordered separately.
Specifications: Probe Body Endcap Seal Fill Material Temperature Rating Pressure Rating Mounting 316 Stainless Steel Glass Ceramic or Epoxy 500 F / 260 C. 3000 PSI/204 Bar 1 inch NPT Pipe Plug
I.L (max) 6.92 10.92 16.92

Model LP2 Linear Polarisation Fixed Length Pipe Plug Probe Pipe Plug Size 3 1 inch NPT Probe Body Material 22 316 LP Electrode Options 10 Three-electrode plug type 30 Three-electrode integral type Seal Type 1 Glass Length 08 6.92 inch max. insertion length 12 10.92 inch max. insertion length 18 16.92 inch max. insertion length Options 000 None LP2 3 22 30 1 08 000 Example of Probe Ordering #

Model LP3000 - Linear Polarisation Resistance Probe Adjustable Length with 0.75 Inch NPT Fitting and 2-Electrode Endcap
Model LP3000 Linear Polarisation Resistance Probe is commonly used in laboratory bypass-loop, and field applications. The assembly consists of a 0.75 inch NPT compression fitting, an insertion rod with a hermetically sealed two electrode endcap and a six-pin connector welded in place. The insertion length (I.L.) is calculated to the end of the electrode and can be specified by the customer. For standard probes, the maximum insertion length is given in the chart below. Several standard electrodes are available to meet your specific needs.
Specifications: Probe Body Endcap Seal Fill Material Temperature Rating Pressure Rating Mounting 316 Stainless Steel Glass Ceramic or Epoxy 500 F/260 C. 1500psi/102 Bar 0.75 inch NPT
STD. LENGTH 6" 8" 12" 18"
I.L. (max) 5.25 7.25 11.25 17.25

Model LP3 Linear Polarisation Adjustable Length Pipe Plug Probe Pipe Plug Size 2 0.75 inch NPT 3 1 inch NPT Probe Body Material 22 316 LP Electrode Options 20 Two-electrode integral type Seal Type 1 Glass Length 06 5.25 inch max. insertion length 08 7.25 inch max. insertion length 12 11.25 inch max. insertion length 18 17.25 inch max. insertion length Options 000 None LP3 2 22 20 1 08 000 Example of Probe Ordering #
Alloy Chart Code Description 375 C1010 419 CDA110 434 CDA443 159 316L S.S. UNS# G10100 C11000 C44300 S31603

Model LP3010 - Epoxy Probe
Model LP3010 Linear Polarisation Resistance Probe is commonly used in laboratory bypass-loop and field applications. The probe (with additional instrumentation) can be used to monitor corrosion rates, evaluate materials and screen corrosion inhibitors. The assembly consists of a glass epoxy probe with an optional 0.75 inch NPT Nylon compression fitting for insertion into the system. The Studs for mounting the electrodes and the six pin connector are held in place by the epoxy fill material. The insertion length (I.L.) is 6.75 inches when the compression fitting is used and 8.75 inches when the fitting is not used. Electrodes are ordered separately.
Specifications: Class Epoxy Probe Body Epoxy Endcap Seal Epoxy Fill Material Temperature Rating 150o F/65o C. (with Nylon compression fitting) (without Nylon compression fitting) 300oF/150o C. 100psi/7 Bar Pressure Rating 0.75 inch Pipe Plug Mounting

Model LP3 Linear Polarisation Adjustable Length Pipe Plug Probe Pipe Plug Size 2 0.75 inch NPT Probe Body Material 7 Epoxy Mount (Pipe Plug) Material 0 No adjustable pipe plug fitting E Nylon LP Electrode Options 20 Two-electrode integral type Seal Type 3 Epoxy Length 11 11 inch Options 000 None LP3 2 7 E 20 3 11 000 Example of Probe Ordering #

Model LP3100 - Linear Polarisation Resistance Probe Adjustable Length with 1 Inch NPT Fitting and 3-Electrode Endcap
Model LP3100 Linear Polarisation Resistance Probe is commonly used in laboratory bypass-loop, and field applications. The assembly consists of a 1 inch NPT compression fitting, an insertion rod with a hermetically sealed three electrode endcap and a five-pin military connector mounted in place. The insertion length (I.L.) is calculated to the end of the electrode and can be specified by the customer. For standard probes, the maximum insertion length is given in the chart below. This maximum I.L. is based on the length of a carbon steel electrode. Electrode lengths may vary depending on the alloy. Electrodes are ordered separately.
Specifications: Probe Body Endcap Seal Fill Material Temperature Rating Pressure Rating Mounting
Stainless Steel Glass Ceramic or Epoxy 500 F/260 C. 1500psi/102 Bar 1 inch NPT
I.L. (max) 5.8 9.8 15.8

Model LP3 Linear Polarisation Adjustable Length Pipe Plug Probe Pipe Plug Size 3 1 inch NPT Probe Body Material 22 316 LP Electrode Options 10 Three-electrode plug type 30 Three-electrode integral type Seal Type 1 Glass Length 08 5.8 inch max. insertion length 12 9.8 inch max. insertion length 18 15.8 inch max. insertion length Options 000 None LP3 3 22 30 1 08 000 Example of Probe Ordering #

Model LP4000 - Linear Polarisation Resistance Probe with 2-Electrode Endcap and Packing Gland
Model LP4000 Linear Polarisation Resistance Probe is commonly used in high pressure and high temperature applications. A specially designed packing gland is used with the probe for insertion into or retraction from a pressurised system without a process shutdown. The packing gland is designed to mount easily on a 1 inch piping system, but it can be modified for your specific mounting requirements. The probe assembly consists of a packing gland, an insertion rod with a hermatically sealed 2 electrode endcap and a six-pin connector welded in place. A safety cable is also provided to prevent blowout. Standard packing material in the packing gland is Teflon, however, graphoil packing can be provided for high temperature applications. The insertion length (I.L.) is calculated to the end of the electrode and can be specified by the customer. Electrodes for the probes can be ordered separately. Several standard electrodes and probe lengths are available to meet your specific needs.
Specifications: Probe Body Endcap Seal Fill Material Temperature Rating Pressure Rating Mounting 316 Stainless Steel Glass Ceramic 500 F/260 C. - Teflon 1200 F/649 C. - Graphoil 1500psi/102 Bar 1 inch Full Port Valve (Min)
STD. LENGTH 18" 24" 30" 36" 42"
I.L. (max) 11.53 17.53 23.53 29.53 35.53
Metal samples Easy Tool is recommended for probe insertion or retraction in systems with pressure over 150 pounds.

Model LP45 Linear Polarisation 1 inch Female NPT Probe with Packing Gland Probe Body Material 22 316 44 C276 LP Electrode Options 20 Two-electrode integral type Seal Type 1 Glass Length 18 11.53 inch max. insertion length 24 17.53 inch max. insertion length 30 23.53 inch max. insertion length 36 29.53 inch max. insertion length 42 35.53 inch max. insertion length Options 000 None LP45 22 20 1 18 000 Example of Probe Ordering #

Model LP4100 - Linear Polarisation Resistance Probe with 3-Electrode Endcap and Packing Gland
Model LP4100 Linear Polarisation Resistance Probe is commonly used in high pressure and high temperature applications. A specially designed packing gland is used with the probe for insertion into or retraction from a pressurised system without a process shutdown. The packing gland is designed to mount easily on a 1 inch piping system, but it can be modified for your specific mounting requirements. The probe assembly consists of a packing gland, an insertion rod with a hermatically sealed 3-electrode endcap and a five-pin military connector mounted in place. A safety cable is also provided to prevent blowout. Standard packing material in the packing gland is Teflon, however, graphoil packing can be provided for high temperature applications. The insertion length (I.L.) is calculated to the end of the electrode and can be specified by the customer. For standard probes, the maximum insertion length is given in the chart below. This maximum I.L. is based on the length of a carbon steel electrode. Electrode lengths may vary depending on the alloy. Electrodes are ordered separately.
Specifications: Probe Body Endcap Seal Fill Material Temperature Rating Pressure Rating Mounting 316 Stainless Steel Glass Ceramic 500 F/260 C. - Teflon 1200 F/649 C. - Graphoil 1500 PSI/102 Bar 1 inch Full Port Valve (Min)
STD. LENGTH 18" 24" 30" 36" 42"
I.L. (max) 11.53 17.53 23.53 29.53 35.53
Metal samples Easy Tool is recommended for probe insertion or retraction in systems with pressure over 150 pounds.

Model LP45 Linear Polarisation 1 inch Female NPT Probe with Packing Gland Probe Body Material 22 316 44 C276 LP Electrode Options 10 Three-electrode plug type 30 Three-electrode integral type Seal Type 1 Glass Length 18 11.53 inch max. insertion length 24 17.53 inch max. insertion length 30 23.53 inch max. insertion length 36 29.53 inch max. insertion length 42 35.53 inch max. insertion length Options 000 None LP45 22 30 1 18 000 Example of Probe Ordering #
Alloy Chart Code Description 377 C1018 159 316L S.S. 419 CDA110 434 CDA443 UNS# G10180 S31603 C11000 C44300

Model LP4104 - Linear Polarisation Resistance Probe with Packing Gland Flange and 3-Electrode Endcap
All Dimensions in Inches Model LP4104 is a retractable length, flange mounted Linear Polarisation Probe. The probe is ideally suited for use in high pressure and/or hazardous applications where threaded fittings are not available. A specially designed packing gland is used with the probe for insertion into or retraction from a pressurised system without a process shutdown. The packing gland is designed to mount easily on a 1 inch piping system, but it can be modified for your specific mounting requirements. The probe assembly consists of a packing gland, an insertion rod with a hermatically sealed 3-electrode endcap and a five-pin military connector mounted in place. A safety cable is also provided to prevent blowout. Standard packing material in the packing gland is Teflon, however, graphoil packing can be provided for high temperature applications. The insertion length (I.L.) is calculated to the end of the electrode and can be specified by the customer. For standard probes, the maximum insertion length is given in the chart below.
Specifications: Probe Body Endcap Seal Fill Material Temperature Rating Pressure Rating 316 Stainless Steel Glass Ceramic 500 F/260 C. According to Flange Rating
STD. LENGTH 18" 24" 30" 36"
I.L. (max) 11.53 17.53 23.53 29.53

Model LP45 Linear Polarisation Fixed Length Probe with Flange with Packing Gland Flange Size 1 1 inch Flange 2 1.5 inch Flange 3 2 inch Flange 4 3 inch Flange 5 4 inch Flange 6 0.5 inch Flange 7 6 inch Flange Probe Body Material 22 316 44 C276 LP Element Options 10 Three-electrode plug type 30 Three-electrode integral type Flange Pressure Rating 10 150 lb 20 300 lb 30 600 lb 40 1200 lb 50 1500 lb 60 900 lb Length 18 14.85 inch max. insertion length 24 20.85 inch max. insertion length 30 26.85 inch max. insertion length 36 32.85 inch max. insertion length Seal Type 1 Glass Options 00 None LP45 2 22 30 20 18 1 00 Example of Probe Ordering #
Code 377 159 419 434
Alloy Chart Description C1018 316L S.S. CDA110 CDA443
UNS# G10180 S31603 C11000 C44300

Model LP7000 - Linear Polarisation Resistance Probe (2 Electrodes)for the 2 inch Access System
Model LP7000 Electrical Resistance Probe is a fixed-length probe for use with the 2 inch access system at high pressure and high temperatures. The probe assembly consists of an insertion rod with a hermatically sealed two electrode endcap, a hollow plug nut, and a standard six pin connector, which are all welded in place. The hollow plug nut on the probe screws into the hollow plug of the access system. This allows the probe to be installed in the process, using a retriever tool and service valve, without process shutdown. Several standard elements and probe lengths are available to meet your specific needs. Probe adaptors are also available and must be ordered separately. (Refer to the Element and Alloy Selection Chart below for more information).
Specifications: Probe Body Fill Material Temperature Rating Pressure Rating Mounting - 316 Stainless Steel - Ceramic - 500F/260C - 3600 PSI/245 Bar - 2 Access System with Hollow Plug

Model HL Linear Polarisation Two-Electrode Probe for High Pressure Access System Mounting Material 2 316 3 C276 Connector Type 1 Small Connector 2 Standard Connector LP Electrode Options 0 Two-electrode integral type 3 Two-electrode flush integral type 5 Two-electrode flush adjustable type Seal Type 0 Glass 1 Epoxy Length XXXX Length in inches, stated in 2 decimal place format (Ex: 6.25 inches = 0625 Options 000 None HL 2 2 0 0 625 000 Example of Probe Ordering #

Model LP7100 - Linear Polarisation Resistance Probe with 3-Electrode Endcap
Model LP7100 Linear Polarisation Resistance Probe is a fixed-length probe for use with a 2 inch access system at high pressure and high temperatures. The probe assembly consists of an insertion rod with a hermatically sealed 3-electrode endcap, a hollow plug nut and a standard six pin connector, which are all welded in place. The hollow plug nut on the probe screws into the hollow plug of the access system. This allows the probe to be installed in the process, using a retriever tool and service valve, without process shutdown. The insertion length is equal to that of the LENGTH and can be specified by the customer. Several standard electrodes are available to meet your specific needs. Probe adaptors are also available and must be ordered separately.
Specifications: Probe Body Endcap Seal Fill Material Temperature Rating Pressure Rating Mounting
316 Stainless Steel Glass Ceramic 500 F/260 C. 3600psi/245 Bar 2 inch Access System with Hollow Plug

Model HL Linear Polarisation Three-Electrode Probe for High Pressure Access System Mounting Material 2 316 3 C276 Connector Type 1 Small Connector 2 Standard Connector LP Electrode Options 1 Three-electrode integral type Seal Type 0 Glass Length XXXX Length in inches, stated in 2 decimal place format (Ex: 6.25 inches = 0625 Options 000 None HL 2 2 2 0 625 000 Example of Probe Ordering #
Code 377 159 419 434 Description C1018 316L S.S. CDA110 CDA443 Alloy Chart UNS# Electrode Length (EL) G10180 1.72 inches S31603 1.62 inches C11000 3.50 inches C44300 3.17 inches

Model LP7210 - Linear Polarisation Resistance Probe Retrievable with Flush-Mount 3-Electrode Endcap for High Pressure (HP TM and MH TM Access Systems
Model LP7210 is a fixed-length, flush-mount, three electrode, retrievable, linear polarisation resistance probe for use with HP TM and MH TM high pressure access systems. These probes are ideally suited for applications where the probe electrodes need to be flush with the wall of the pipe. The probe assembly consists of an insertion rod, a flush mount, three-electrode endcap and a six-pin military connector. The hollow plug nut on the probe screws into the hollow plug of the access system. This allows the probe to be installed in the process, using a retriever tool and service valve, without process shutdown. The probe's three-electrode endcap is filled with an epoxy seal. Electrodes are not replaceable. The insertion length (I.L.) can range from a minimum of 1.75 inches up to any length specified by the customer, using the formula: I.L. = PD + WT + 1.75" (where PD=penetration depth, WT=wall thickness) For top-of-the-line, flush-mount monitoring, PD=0 Note: Formula valid for access fitting heights of 5.25" (HP) and 5.5" (MH)
Specifications: Probe Body Endcap Seal Fill Material Temperature Rating Pressure Rating Mounting 316 Stainless Steel Epoxy Epoxy 500 F/260 C. 3600psi/245 Bar High Pressure Access System with Hollow Plug

Model HL Linear Polarisation Three-Electrode Probe for High Pressure Access System Mounting Material 2 316 3 C276 Connector Type 2 Standard Connector LP Electrode Options 4 Three-electrode integral flush type 6 Three-electrode integral flush adjustable type Seal Type 1 Epoxy Length XXXX Length in inches, stated in 2 decimal place format (Ex: 6.25 inches = 0625) Electrode Alloy XXX Use Code in Alloy Chart HL 2 2 4 1 0625 XXX Example of Probe Ordering #

Electrodes for Electro-Chemistry
Gaskets Commonly used with Electro-Chemical Apparatus

System Accessories
Cables

Factory Assembled: For Portable Instrument Series P.N 700716 + Length For Transmitter and Data Collection Systems P.N. 700726 + Length Cable - Heavy Duty: P.N 700331 Two wire for transmitter P.N. 700431 Connectors: Low Pressure Probe Type A P.N. 700521 System High Pressure Type B P.N. 700343
Probe to Cable Adaptor for 2" High Pressure System

Portable with Standard 6 pin Connector P.N. 700319 Portable with Small 6pin ConnectorFixed P.N. 700033 Fixed Adapter with Standard 6 pin Connector P.N. 700640 Fixed Adaptor with Small 6pin Connector P.N. 700077
Shield Options

Standard Shield - Wire Loop Probe - P.N. 700608 High Velocity Shield - Wire Loop Probe - P.N. 700609 Standard Shield - Cylindrical Probe - P.N. 700610 High Velocity Shield - Cylindrical Probe - P.N. 700611 Coupon Holder Shield - Wire Loop Probe - P.N. 700612 Coupon Holder Shield - Cylindrical Probe - P.N. 700613
Safety Clamps

For 18" and 24" Probe lengths P.N. 700700 For 30", 36" and 42" Probe lengths P.N. 700701

Model RT 6000 - Coupon Insertion System Fixed Length with Flange
Model RT 6000 is a fixed-length, flange-mounted, coupon insertion system. The probe is ideally suited for use in high pressure and/or hazardous applications where threaded fittings are not available or not recommended. Process shutdown or process isolation is required for installation and inspection. The probe assembly consists of an insertion rod with an element and a flange (as specified by customer) which are all welded in place. Insertion length (I.L.) is calculated to the end of the coupon in this case, is based on a 1 inch total flange thickness. Customers can specify any length required. For standard probes, the maximum insertion length is given in the chart below.
Specifications: Probe Body Temperature Rating Pressure Rating Mounting
316 Stainless Steel 500 F/260 C. According to Flange Rating Mating Flange
STD. LENGTH 8" 12" 18" 24"
I.L 6 10 16 22
BACK TO WEIGHT LOSS COUPON MENU

RT 6000 ORDERING INFORMATION
Model RT6 Coupon Insertion System with Flange Flange Size 1 1 inch Flange 2 1.5 inch Flange 3 2 inch Flange 4 3 inch Flange 5 4 inch Flange 6 0.5 inch Flange 7 6 inch Flange Probe Body Material 22 C316 44 C276 Coupon Options 010 Fits P/N C0100 030 Fits P/N C0118 050 Fits P/N C0111 060 Fits P/N C0220 Flange Pressure Rating 1 150 lb 2 300 lb 3 600 lb APPEND A FOR RF FLANGES 4 1200 lb APPEND B FOR RTJ FLANGES 5 1500 lb 6 900 lb Length 08 06.00 inch max. insertion length 12 10.00 inch max. insertion length 18 16.00 inch max. insertion length 24 22.00 inch max. insertion length 36 34.00 inch max. insertion length FOR LENGTHS OTHER THAN STANDARD INSERT THE ACTUAL LENGTH IN INCHES RT6 2 22 50 1A 12 Example of Probe Ordering #

Model SR4000 - Coupon Insertion System with Packing Gland
Model SR4000 coupon insertion systems are retractable and commonly used in high pressure and high temperature applications. A specially designed packing gland is used to insert or retract a coupon from a pressurised system without a process shutdown. The insertion system is designed to mount onto a 1 inch piping system, but can easily be adapted to fit your specific requirements. The system consists of an insertion rod with a coupon holder, and a packing gland. A safety cable and safety nut, are also provided to prevent blowout. Standard packing material in the packing gland is Teflon, however, Graphoil packing can be provided for high temperature applications. Several coupon holders and lengths are available.
Specifications: Probe Body Temperature Rating Pressure Rating Mounting STD. LENGTH I.L (max) 18" 11.53 24" 17.53 30" 23.53 36" 29.53 42" 35.53 316 Stainless Steel 500 F/260 C. 1000psi/68 Bar 1 inch Full Port Valve (Min)
Metal Samples Easy Tool is recommended for probe insertion or retraction in systems with pressure over 150 pounds

SR4000 ORDERING INFORMATION
Model SR45 Retractable Coupon Insertion System 1 inch Female NPT with Packing Gland Insertion Rod and Mounting Material 22 316 44 C276 Coupon Options 010 Fits P/N C0100 030 Fits P/N C0118 050 Fits P/N C0111 060 Fits P/N C0220 Length 18 12.54 inch max. insertion length 24 18.54 inch max. insertion length 30 24.54 inch max. insertion length 36 30.54 inch max. insertion length 42 36.54 inch max. insertion length Coupon Adapter and Insulators 1 Coupon adapter same material as rod, teflon insulators. 2 Teflon coupon adaptor, teflon insulators. 3 Coupon adapter same material as rod, ceramic insulators. 4 Coupon adapter same material as rod, nylon insulators. 5 Nylon coupon adaptor, nylon insulators. 6 Coupon adapter same material as rod, no insulators. RT450 22 30 18 1 Example of Probe Ordering #

Two-inch System HC Series Coupon Probes
HC Series Probes are used in conjunction with the TRISEAL High Pressure Access Fitting Assembly. The Coupon Probe is attached to the Solid Plug Assembly by means of an O.D. left handed thread connection and also retains the primary packing. Disc Coupon Probes are primarily intended for use in areas where pigging operations prohibit the use of projecting style probes. Additional advantages are the lack of requirement to orient the coupon relative to the flow direction and a greater exposed surface area at the pipe wall. Coupon Probes are manufactured in 316 SS and are available in lengths from 2.50 inches to 36 inches. To calculate the correct ordering length, use the following formula. ORDERING LENGTH =P + W + 2.50 inches where P = Penetration required in pipe W = Wall thickness of pipe Note: Formula is based upon a standard access fitting height of 5.25 inches and 0.0625 weld gap per ANSI B31.1.1973. Corrosion Coupons can be supplied in most alloys and are complete with Coupon. Accessories for Disc Coupon Probe Mounting Kit - P/N 700620 Accessories for Strip Coupon Probe Screw 0.25 - 20.1.00 - St. St. Mounting Kit - P/N 700567 Coupon Insulation Washer Teflon Washer
Multiple Disc Coupon monitoring is suitable for pipes with I.D. greater than 6.00 inches. Multiple Disc Monitoring permits coupons to be placed at a specific level in multi phase or stratified flow. The coupons are insulated from the probe rod by Nitrile O rings. Delrin or Nylon Spacers are used to provide insulation between coupons. Materials of construction satisfy the requirements of NACE MR-01-75 PROBE SIZING (Flarweld Access Fitting - 5.25 inches Height) Calculate the Probe length as follows: L = K + D - W -2.75 L = Probe Holder Length K = 5.31 (Constant) D = Pipe O.D. W = Pipe Wall Thickness Round down to the nearest 0.125 inches Rod Length R = L - 1.9375 Coupon Position Top of Line Coupon C1 = K + W - 3.8125 Middle of Line Coupon C2 = K + D/2 - C1 - 4.125 Bottom of Line Coupon C3 = R - C1 - C2 0.375 C1 + C2 + C3 + 0.375 must equal R (Rod length) TO ORDER Determine Rod Length. Order using format detailed in Ordering Chart. Determine the length and quantity of coupon to coupon insulation spacers. Determine the number of Coupon-Rod Bushings required.
Ladder Strip Coupon Monitoring is suitable for pipes 8 inch O.D. and greater. The probe body is a single blade containing holes spaced along its length for mounting the coupons. A minimum probe length of 26 cm (10.25") is required to mount three pairs of coupons. PROBE SIZING Calculate the probe length required as follows: L = (5.31 + D) - (2.50 + W) L = Probe Length D = Pipe O.D. W = Pipe Wall Thickness This formula should only be used for Access Fitting Bodies with 5.25 height. For flanged Access Fitting Body installations, please call the sales office.
TO ORDER Accessories for Multi Disc Coupon Probe Bushing - O Ring Insulation Spacers Available in 0.0625 increments from 1 inch to 2 inches Accessories for Ladder Strip Coupon Probe Mounting Kit - Coupon
Applied Stress Coupons are 152mm (6 inches) long, 22.3mm (0.875 inches) wide, 3.18mm (0.125 inches) thick. An insulated adjusting screw located on the coupon mid-point applies stress to the coupon. NOTE: Applied stress coupons have been stamped on the end because this is the lowest stress area and cracking is not expected to be initiated by the identification mark. Applied stress is determined from the number of adjusting screw turns or bending deflection. The coupons are first stressed and then installed in the line. The time required for cracks to develop is determined by pulling coupons at regular intervals, usually 24 hours to 30 days. Test duration will vary with the stress level applied to the coupon. The time to crack may then be used as a measure of stress corrosion resistance. Test start time begins when stress is applied and the stressed coupon is exposed to the corrosive environment, whichever occurs later. The coupon is considered to have failed when cracks appear. The cracks may be detected by optical, mechanical or electrical means. Cracking time is the elapsed time from test start until the appearance of cracks. Formula for Applied Stress Coupons S = 6Ety/H Where: S = maximum tensile stress E = modulus of elasticity t = thickness of coupon y = maximum deflection The formula is for longitudinal stress in the outer fibres of the coupon, below the elastic limit of the material. At stress above the elastic limit, but below the yield strength at 0.2% error results. The formula must not be used above the yield strength of the material. NOTE: The formula is based on small deflections i.e. y/H is less than 0.1.
HIGH PRESSURE COUPON HOLDER ORDERING INFORMATION CHART
HC
X | COUPON TYPE 1 - Strip coupon 2 - Ladder Strip 3 - Flush Disc Fixed 4 - Flush Disc Adj. 5 - Multi Disc 6 - Single Prestressed 7 - Multi Prestressed
X | PROBE TYPE 1 - Welded 2 - Non Welded
X | PROBE ALLOY 1 - 316 SS 2 - Hastelloy C276
XX.XX | PROBE LENGTH 2 to 40 in 1/8 Increments. For Flush Disc Adjustable put VA.RY.

Coupon
Coupons are supplied ready for use.

C1018 coupons are stamped with a sequence number. All alloy coupons are stamped with the alloy and sequence number. Coupons are pre-weighed and individually packaged in a Data Front VCI bag. Coupons are supplied with a mill test report and a weight log chart. Coupons are cleaned of all contaminants and have a sand blasted finish. Nylon insulators are mounted into coupons. ORDERING INFORMATION
XXXX | Coupon Material Code 3 inch Strip 111 01 - 1018 C.S. 6 inch Strip 169 02 - 304 S.S. 2 inch Ladder 197 03 - 304L S.S. Flush Disc 142 04 - 316 S.S. Multi Disc 141 316L S.S. 3 inch Scale 185 06 - 410 S.S. 6 inch Scale 196 07 - 5LGrB 08 - A106 GrB 09 - A33GrB Example: P/N 111-1018 is a 3 inch Strip Coupon in C1018 C.S.
XXX | Part Number
=Ordering Number Material Code A - 5LX52 B - 5CT L80 -1 C - 5CT N80 D - A333 Gr3 E - 5LX65 F - UNS 2205 G - 70/30 CuNi H - 90/10 CuNi
Two-inch System
Standard Coupons 6 Inch Strip Coupons: This coupon is used when a larger exposed area is required. The exposed surface area is 73.5cm 2(11.4 inch2). Dimensions 152 x 22 x 3.2mm (6 inch x 0.875 inch x 0.125 inch). The coupon has two mounting holes. 3 Inch Strip Coupons: 76.3 x 22 x 3.2mm (3inch x 0.875inch x 0.125inch) with two mounting holes and have an exposed surface area of 35.35cm2 (5.47in2). Special Corrosion Coupons Pre-stressed Coupons: are used where sulfide stress corrosion cracking is a factor. Pre-stressed coupons come in two sizes: 6 inch for single coupon and 4 inch for the multiple type.
Ladder Stripped Coupons: are designed for simultaneous corrosion monitoring at top, middle and bottom positions in a pipeline. Dimensions 51 x 22 x 32mm (2inch x 0.875inch x 0.125 inch) with two mounting holes. The exposed surface area is 21cm2 (8.27in2) Scale Coupons: are of the same size as the 3inch strip coupon, but has a series of holes of different size range. Scale usually forms on cavities therefore it is likely to form on small sized holes.
Flush Disc Coupons: dia. 31.8 x 3.2mm (dia. 1.25 inch x 0.125 inch) are utilised where the coupons should not extend into the pipe or interfere with the media flow or pig passage. The exposed area is about 17cm2 (2.6 in2).
Disc Coupons: Are utilised for stacked Residual Stress Coupons: are rectangular multiple phase monitoring when the line coupons similar to the 3 inch strip diameter is 6 inches or more. For pipelines coupons, but are deformed to create less than 6 inches it is recommended to residual stress. This type of coupon use single disc. Dimensions dia. 31.8 x stimulates any corrosion effect due to the 3.2mm (dia. 1.25 inch x 0.125 inch). The residual stress present in combination with exposed surface area is about 17cm 2 (2.6 an embrittling environment. inch2). Rod Coupons: This is a rod protruding Crevice Corrosion Coupons: are made into the product flow. Standard rods are from the standard Disc Coupon, available in a size of 101.6 x dia. 6.35mm. dimensions 31.8 dia. x 3.2mm (1.25 inch (4 inch x 0.25 inch dia.). One end of the dia. x 0.125 inch) with a nylon disc on rod is threaded with 0.25inch UNC to each side held in position by a stainless screw the rod into the holder. The exposed steel screw. area is about 21.09cm2 (3.27in2).
Standard Coupon Specifications

Accurate monitoring of corrosion rates in any environment is critical when viewed in terms of the maintenance and repair costs associated with corrosion and material failure. Test coupons can provide an inexpensive means of effectively monitoring corrosion levels in a system. By observing the mils-per-year corrosion rate of an exposed coupon, valuable information can be provided regarding the material's life expectancy. The following coupons are commonly used in corrosion testing. Rose Corrosion Services can supply specimens in any size, shape or material you need.
P/N CO100
P/N CO131
Shape: Finish: Indentification: Mounting Hole: Cutting:
Rectangular Double disc or glass bead. Stencilled-alloy, heat no sequence. Drilled/Laser Cut Laser Cut/Punched
Shape: Finish: Indentification: Mounting Hole: Cutting:
Rectangular 120 grit, glass bead or mill. Stencilled-alloy, heat no sequence. Drilled/Laser Cut Saw Cut/Laser Cut
P/N CO146
P/N CO220
Shape: Finish: Identification: Mounting Hole: Cutting:
Rectangular Glass bead or mill. Stenciled-alloy, heat no sequence. Punched/Laser Cut Laser Cut/Sheared
Shape: Finish: Identification: Mounting Hole: Cutting:
Circular 120 grit, glass bead or mill. Stenciled-alloy, heat no sequence. Drilled/Laser Cut Turned/Laser Cut
Coupons can be furnished with a variety of finishes depending on your particular application. Some of the typical finishes are defined below: Mill - finish as produced from mill. Glass Bead - blasted with fine glass beads to remove mill scale. 120 Grit - fine finish using a 120 grit belt and commonly used in corrosion tests, such as pitting studies, where smooth surface finish is desired. Finishes up to 800 grit (extremely fine) can be provided by using belt sanders. Double Disc Ground - extra fine finish using an abrasive disc that leaves minimal residual grit. Excellent for studies where surface finish is critical. Capable of producing 16-32 RMS finishes on common steels and 8 RMS on carbide steels.

Corrosion Test Supplies for the Water Treating Industry
Rose Corrosion Services Ltd. provides the water treatment industry with a wide assortment of corrosion test supplies. We specialise in expeditious order processing of test coupons made according to your needs for material, size, shape and finish. Coupons can be stenciled with alloy and sequence numbers for proper identification, and the pre-weighed and measured to help assure the integrity of your test data.
STANDARD WATER TREATING COUPONS*

P/N CO100** CO101 CO102 CO103 CO104 CO105 CO106 CO115*** CO117 CO118 CO120 SIZE " x 3" x 1/16" 1" x 2" x 1/16" " x 3" x 1/16" " x 3" x 1/16" " x 3" x 1/16" " x 3" x 1/16" " x 3" x 1/16" " x 3" x 1/16" " x 3" x 1/16" " x 3" x 1/16" " x 3" x 1/16" HOLE 3/16" 3/16" 9/64" " (2) " 3/16" " " 9/64" (2) " (2) " HOLE LOCATION " fr.end " fr.end " fr.end " fr.end " fr.end " fr.end " fr.end " fr.end " fr.end " and " end " and " end AREA IN SQ.IN 3.38 4.32 3.41 3.34 3.24 3.38 3.34 2.64 3.24 2.48
*Table refers to standard water treating coupons made from C1010 material. **Standard P/N CO100 comes with rounded corners. STANDARD PIPE PLUG ASSEMBLIES
P/N 2077NA 2079NA 2077TA 2079TA 2078NA 2081NA 2078TA 2081TA 2087NA 2088NA 2087TA 2088TA 2084NA 2075NA 2084TA 2075TA 2092NA CARBON STEEL OR MATCH WITH COUPON 3" (std) STEM PVC PLUG NUMBER " NPT Nylon CO102,CO117 1" NPT Nylon CO102,CO117 " NPT Teflon CO102,CO117 1" NPT Teflon CO102,CO117 " NPT Nylon CO100,CO103,CO115 1" NPT Nylon CO100,CO103,CO115 " NPT Teflon CO100,CO103,CO115 1" NPT Teflon CO100,CO103,CO115 " NPT Nylon CO118,CO120 1" NPT Nylon CO118,CO120 " NPT Teflon CO118,CO120 1" NPT Teflon CO118,CO120 " NPT Nylon CO105,CO106 1" NPT Nylon CO105,CO106 " NPT Teflon CO105,CO106 1" NPT Teflon CO105,CO106 " NPT Nylon CO100,CO103,CO115
A variety of plug sizes and stem lengths are available. CYLINDRICAL COUPONS (C1018 STD) P/N SIZE THREAD ES200 " x 2.5" "-20 x 3/8" ES201 " x 2" "-20 x 3/8" ES202 " x 3" "-20 x 3/8" ES204 x 1 -20 x 3/8"
SLOT 1/16" 1/16" 1/16" 1/16

Corrosion Test Supplies for the Water Treating Industry TEST RACKS
Specimen Exposure racks are used to mount test samples and secure them directly to operating equipment within the industrial environment. The usage helps eliminate coupon loss which might occur if samples were individually placed in the process flow. Rack usage also allows samples of differing alloys and materials to be studied in the same test.
ALLOYS AVAILABLE
Coupons are available in the following allows. Please call for pricing.
ALLOYS AVAILABLE (Cont.)


SCROLL DOWN FOR FOURH PAGE

SCROLL DOWN FOR FIFTH PAGE

SCROLL DOWN FOR SIXTH PAGE

SCROLL DOWN FOR SEVENTH PAGE

SCROLL DOWN FOR EIGTH PAGE


Model SP7000 - Sand Probe for High Pressure Access Systems
Model SP7000 Sand Probes are used to detect erosion in flowlines caused by abrasive particles such as sand. One end of the probe is attached to a tee-type, high pressure access fitting with a solid plug by means of a sand probe nut. The other end is sealed, thin walled tube placed with the process stream to be exposed to particulate flowing through the system. (To minimise the effects of corrosion and thus more accurately detect erosion with the stream, the exposed element is made of stainless steel). As particulate impinges on the surface of the sensing element, a hole is eventually eroded through the element. Once penetration has occurred, the system pressure then travels up the tube, into the access fitting body, and through a nipple and valve to a pressure gauge assembly. The pressure gauge detects that the element has been breached. If required, electronic pressure sensors can be connected to alarm systems to signal the exact moment when failure occurs.
Specifications: Stainless Steel Probe Body 500 F/260 C Temperature Rating 3600psi/245 Bar Pressure Rating High Pressure Access System with Solid Plug Mounting Sand Probe Parts Part No. Description HA700018 Nipple, 0.25 inches x 4 inches Sch 80 HA 700322 Valve. 0.25 inches HA700221 Sand Probe Nut HA700603 Pressure Gauge HA700121 Solid Plug
BACK TO MISCELLANEOUS MENU

SP7000 ORDERING INFORMATION
Model SP Sand Probe for High Pressure Access Systems Mounting Material 2 316 3 S31803 4 C276 Tube Material 2 316 3 S31803 4 C276 Tube Wall Thickness 1 0.016 inches 2 0.028 inches 3 0.035 inches Length XXXX Length in inches, stated in 2 decimal places format (Ex:6.25inches = 0625) SP 2 2 1 0625 Example of Probe Ordering#

Model HC6200 Bio-probe
Model HC6200 bio-probe is used to collect samples of bacteria in gas and oil producing systems. The bacterial population on a system's metal surfaces more relevant to corrosion than the bacteria population in the system's fluids. This is because only surface or sessile bacteria cause corrosion. Thus a corrosion control program is ineffective unless it kills those bacteria which have formed attached biomasses. The same bacteria which cause problems in gas pipelines, tanks, vessels, oil wells and water handling systems attach to the bio-probes sample element. Since the bio-probe is designed for high pressure access systems, common throughout the oil field, it becomes a convenient and economical way for sampling corrosion-causing biological activity.
Part No
Description Bio-probe Assembly with Delrin holder (XXXX = insertion length in inches, stated HC62158XXXX in 2 decimal place format) EL438 Biological Sample Elements, C.S. HA 700120 Solid plug, High Pressure Access System, 316 Item No. Description Material 1 Heavy Duty Cover Carbon Steel 2 0-ring Viton AE 3 Solid Plug 316 4 Primary Packing (primary seal) 25%G.F.Teflon AE 5 Access fitting Carbon Steel 6 Bacteria sample holder Delrin 7 Bacteria fixture 316 8 0-ring VitonAE 9 Sample element "Bullet" Mild Steel or brass

Model HY7000 - Hydrogen Probe with Gauge Assembly for High Pressure Access Systems
Model HY7000 is a high pressure hydrogen probe which can be used for pressures up to 3600psi. Hydrogen probes are commonly used for monitoring hydrogen permeation in steels, which could lead to embrittlement, blistering and decarburisation resulting in the failure of the material. The probe assembly consists of three subassemblies: the gauge assembly, the hollow plug assembly and the sensing element assembly. The gauge assembly consists of a gauge body, a pressure gauge (0-40psi), a temperature gauge and a bleed valve. The sensing element is about 3.5 inches long and consists of a thin-walled tube which is sealed from the process and allows nascent hydrogen to permeate. The probe can be supplied with or without the gauge assembly, which can be bought separately if required. The minimum length of the probe is 5.50 inches and can be ordered in 0.25 inch increments. Specifications: 316 Stainless Steel Probe Body Temperature Rating 500 F/260 C 3600psi/245 Bar Pressure Rating High Pressure Access System with Hollow Plug Mounting Gauge Assembly Parts Part No. Description PS5509 Gauge Assembly (complete) PR6441158 Pressure Gauge PR6032 Temperature Gauge PR6034 Bleed Valve PR6158158 Gauge Body

Two-Inch System Injection and Sampling System
Injection and Sampling Systems are fundamental to Corrosion Control programs. They are applicable to a large variety of processes in the petroleum, chemical and water treatment industries. Injection systems may be used for the injection into the system of a wide range of chemicals such as biocides, demulsifiers, corrosion inhibitors, oxygen scavenger, glycol and mono-ethylene glycol, dewaxers, methanol, odorisers and a wide range of product activities. Sampling systems, as the name implies are used to take samples of the process fluid medium. Such samples are the analyzed in the laboratory for inhibitor concentration levels, the presence of metal ions, oxygen levels, scale forming compounds and a wide range of process parameters. INJECTION SYSTEMS The art of chemical injection is a complex technology. Irrespective of the type of injection or injected fluid, several factors relative to the process system and the injection system must be considered. Principle factors are: Pressure Differential This is the difference between the injection pump pressure and the process line or vessel pressure. Ideally the pressure differential should be 8 Bar (100psi).
BACK TO CHEMICAL INJECTION MENU
Temperature Temperature directly affects viscosity. Ideally the temperature of both the injected chemical and the line product should be about 21oC (70o). Viscosity This is the measure of fluids resistance to flow. The more viscous the fluid the smaller the spray angle. Spray Angle Spray angle is affected by viscosity, spray distance and pressure differential. Spray Coverage This is calculated theoretical area coverage. Specific Gravity The specific gravity of a liquid is the density ratio of the liquid to water. The flow rate of a liquid is affected by its specific gravity. Injection Rate This is the amount of chemical to be injected within a specified period and is defined as Litres Per Day (LPD) Gallons Per Hour (GPH) etc. Injection systems are available for injection rates varying from 0.38 litres/hour (0.1 GPH) to 250 litres/hour (65.7GPH). Injection may be via a simple open ended tube or a quill that relies upon a natural turbulence within the pipeline to disperse the injected chemical and to accomplish even distribution. There is no restricting orifice and such systems tend to be clog proof even when using unscreened chemicals a disadvantage of such systems is that at low flow rates there tends to be a concentration of the injected chemical at the pipe wall surface below the injection point. INJECTION POINT The maximum fluid velocity is usually at the centre of the line hence the most effective position for injection is generally at the centre of the pipe in the direction of the product flow. If the line is to be pigged, the injection point may be flush with the pipe wall. This eliminates the need to remove the injection probe before pigging operations begin. On pipelines this means that injection is perpendicular to the product flow. Top of the line may be used if the injection is required to be oblique or horizontal to the product flow. A more comprehensive discussion of the factors to be considered in the design of chemical injection systems is contained in the Rose Corrosion Injection Primer. A typical Two Inch System Injection Assembly is shown above. A sampling system uses the same components. The various components of the assembly are: 1. An Access Fitting Body with a side Tee through which the fluid transfer takes place. The Tee may be threaded or welded. Welded Tees are either flanged or
buttweld nipple. Threaded Tees are based on an NPT tapped hole in the fitting body. The Tee size is rated according to the injection rate and injection and viscosity of the injection chemical. 2. A Solid plug Assembly inside the fitting body is used to carry an injection nut which has the injection tube/nozzle assembly screwed to its base. 3. An Injection/Sampling Nut. This is a multiple use nut that replaces the nut of the Solid Plug. It is used to direct the injected product to the injection tube or atomisation device. An Injection Nut sizing chart is shown in Table 1. 4. The Injection or Sampling Tube or Nozzle. The various forms offered are: a. X Open. This is an open tube. The natural turbulence within the pipeline is used to ensure even distribution. The pressure differential is experienced at the orifices so it is necessary to control the injection rate at the injection pump or the shut off valve. b. X Quill. This has a scarf and quill inserted at the open end. It utilizes the turbulence created by its unique design to achieve distribution of the injected chemical into the product flow. Injection Tube x Quill are clog proof and give extremely good dispersion of the inhibitor provided that the product flow is 4.6 metres per second or greater. As with the Open Tube, injection rate must be controlled at the Injection Pump or Shut Off Valve. c. X NPT. Again similar to the Open Tube but is threaded at the dispersion end, thus allowing attachment of female nozzle assemblies. Injection may be perpendicular with the use of a straight nozzle or parallel with a right angle nozzle. d. X Head. This is the usual style used for parallel injection at the centre of the line. The head is integral with the Injection Tube and is designed to accept the Cap and Core from a standard nozzle assembly. 5. Nipples. Nipples are used with threaded Tee Access Fitting Bodies and are the means of connecting the shut off valve to the Access Fitting Body. 6. Shut Off Valves. These are required to cut-off the injection flow and maintain pressure integrity through the Tee when the solid plug assembly is being removed or replaced. They are also used to control the injection flow rate. A nipple and Shut Off Valve sizing chart is given in table 3. 7. Check Valve. These are optional items which may be fitted within the Injection Tube in the intlet line to the Access Fitting Body Tee. 8. Atomisation Nozzles and Cap and Cores. These are the various devices which, attached to the dispersion end of the Injection Tube, permit atomization of the fluid as it is injected into the product line or vessel. Nozzle assemblies are complete units which contain caps, cores, and strainers. They are available with both female and male NPT threads to match the thread on the Injection Tube X NPT. Caps, cores and strainers are component parts of the Nozzle Assemblies. They have male UNF threads which engage with the UNF threads in the dispersion body of the Injection Tube X Head. The correct Nozzle size may be determined from Table 4. 9. The Injection or Feed Pump. The injection pump must be capable of generating sufficient injection line pressure to overcome the line operating pressure and thus create the required pressure differential across the atomizing nozzle or injection tube.
SCROLL DOWN FOR FOURH PAGE
Materials of Construction. All components are manufactured from 316 Stainless Steel as standard with the exception of seals and packing. These materials comply with the requirements of NACE Standard MR 01-75. Recommended materials for sulphide stress cracking environments. INJECTION TUBE SIZING Flush - Non Flange Access Fitting X Open: (FH + PW)-(2.04 + N) = L X NPT: (FH + PW)-(3.353 + N) = L Flush - Flange Access Fitting X Open: (FH + PW + MF)-(2.04 + N) = L Top of Line - Non Flange Fitting X Open (FH + PW + IL)-(2.04 + N) = L X NPT: (FH + PW + IL)-(2.04 + N) = L X Quill: (FH + PW + IL)-(2.04 + N) = L Top of Line - Flange Fitting X Open (FH + PW + IL + MF)-(2.04 + N) = L X NPT: (FH + PW + IL + MF)-(3.363 + N) = L X Quill: (FH + PW + IL + MF)-(2.04 + N) = L Centre of Line - Non Flange Fitting X Quill: (FH + PD/2)-(2.04 + N) = L X Head: (FH + PD/2)-(2.04 + N) = L Centre of Line - Flange Fitting X Quill: (FH + PD/2 + MF)-(2.04 + N) = L Bottom of Line - Non Flange Fitting X Open: (FH + PD)-(2.04 + N + PW)=L Bottom of Line - Flange Fitting X Open: (FH + PD + MF)-(2.04 + N + PW) = L FH = Access Fitting Height PW = Pipe Wall Thickness N = Injection Nut Length L = Injection Tube Length MF = Mating Flange Height IL = Insertion Length into Pipe or Vessel PD = Pipe Outside Diameter
SCROLL DOWN FOR FIFTH PAGE
HOW TO ORDER
A) The Access Fitting Body style and Tee size may be determined from the Access Fitting product literature. B) The Injection Nut size may be determined from Table 1.
Nut Thread Size 1/8 (3.2mm) (6.4mm) (12.7mm) (19.0mm) 1.75 Part Number 700219 700221 700223 700225
Nut Length 3.00 3.50 Part Number Part Number 700220 700227 700222 700228 700224 700229 700226 700230 TABLE 1
3.75 Part Number 700231 700232 700233 700234
5.50 Part Number 700235 700236 700237 700238
Use 1.75 inch Nut Length for Access Fitting Body Height 5.25 inch, use 3.00 inch or 3.50 inch Nut length for 6.25 inch Access Fitting Body Height, use 3.75 inch for 7.25 inch Access Fitting Body Height and use 5.50 inch for 8.25 inch Access Fitting Body Height. C) Determine the Injection Tube type required. Determine the injection point. Calculate the Injection Tube length using the sizing formulas. Use this information to determine the Injection Tube Part Number from Table 2.
Model Injection Tube Type IQ xx required | 1 - X Open 2 - X Quill 3 - X NPT 4 - X HEAD
Material NPT Thread Sizes xx xx | | 01 316 S.S 01 - 1/8 02 - 02 - Other (Specify) 03 - 04 - TABLE 2 Valve 316 S.S. Part Number 700322 700323 700324 700325 TABLE 3
Injection Tube Length xx.xx. = Part. No. | Open/Quill/NPT X Head
Available from 3.2 cm to 76.2cm Available from 5.7cm to 76.2cm
D) A Nipple and Shut Off Valve to match the Tee of the Access Fitting Body may be selected from Table 3
Access Fitting Tee Size 1
Nipple 100mm 316 S.S. Sch 80 Part Number 700018 700019 700020 700021
E) If applicable select a suitable Nozzle Assembly/Cap and Core from Table 4
Part Number 700030 700031 700032 700034 700035 700036 700038 700039 700040
Orifice Diameter/Nozzle Type 0.30 - NPT Fem.N 0.40 - NPT Fem.N 0.60 - NPT Fem.N 0.30 - NPT Flush 0.40 - NPT Flush 0.60 - NPT Flush 0.30 - Cap/Core 9/16 0.40 - Cap/Core 9/16 0.60 - Cap/Core 9/16
GPH Capacity & Pressure Differential 40 PSI 60 PSI 80 PSI 100 PSI 0.3 0.36 0.42 0.48 0.4 0.48 0.56 0.64 0.6 0.72 0.84 0.96 0.3 0.36 0.42 0.48 0.4 0.48 0.56 0.64 0.6 0.72 0.84 0.96 0.3 0.36 0.42 0.48 0.4 0.48 0.56 0.64 0.6 0.72 0.84 0.96 TABLE 4

Model IP4000 - Injection and Sampling System Retractable with Packing Gland
Model IP4000 Injection and Sampling System is a retractable unit commonly used in field and plant applications. A Specially designed packing gland is used with the unit for insertion into or retraction from a pressurised system without a process shutdown. The unit is designed to mount onto a 1 inch piping system, but can easily be adapted to fit your specific requirements. The unit assembly consists of a packing gland and an insertion rod with an injection/ sampling fitting. The fitting, which is threaded or welded to the end of the rod, can be either a quill, open, cap and core or nozzle assembly type. A safety cable is also provided to prevent blowout. In systems with pressure over 150psi, an adaptor for the Easy Tool may be added to the unit. Standard packing material in the packing gland is Teflon however, graphoil packing can be provided for high temperature applications. Model IP4000 units are available in different lengths and materials.
Specifications: Body: Temperature Rating: Pressure Rating: Mounting: STD. LENGTH 18 24 30 36 42 316 Stainless Steel 500F / 260C Teflon 1200F / 649C Graphoil 1500 PSI / 102 Bar 1 Full Port Valve (Min.) I.L. (Max) 12.1 18.1 24.1 30.1 36.1

CHEMICAL INJECTION SKID UNITS
Rose Corrosion Services Limited design and manufacture packaged, skid mounted chemical injection units to meet customer specifications. Pumps are selected on the basis of capacity and service. Storage tanks are designed in accordance with BS 5500 and fabricated from 316 St.St. or Carbon Steel. Supply includes fittings and accessories including:

Interconnecting piping, valving and fittings. Common support frame built in Carbon Steel. Lifting Lugs. Painting of Carbon Steel Metallic Parts. All necessary cable and glands. Frame earthing lugs.
Fields of Application Oil and Gas Industries

Corrosion Inhibitor Injection. Sodium Hyperchlorite Dosing. Bactericide Injection
Two-Inch System Access Fitting Assemblies

TRISEAL*
The TRISEAL* Two Inch System makes it possible to insert and retrieve a complete range of corrosion monitoring, erosion monitoring, biomonitoring, hydrogen monitoring, chemical injection and sampling system probes, quills and nozzles whilst the operating system, vessel or pipeline remains operational and at full operational pressure. A comprehensive range of access fitting assemblies are available in a wide range of styles and materials. Two Inch System Access Fitting Assemblies consist of: 1. 2. 3. The Access Fitting Body. A Solid or Hollow Plug, and A Thread Protector, (Optional)
The Design of the Access Fitting Bodies: Standard and Codes:
ASME B31.3 API RP 14E ASME/ANSI B16.5 NACE MR-01-75
All components of the TRISEAL* System Two Inch System are interchangeable with existing 2 inch high pressure access systems *TRISEAL is a Registered Trade Mark of Rose Corrosion Services Limited
BACK TO ACCESS FITTINGS MENU
Two-Inch High Pressure Access Fittings Ordering Information Chart
1.
To order an Access Fitting Body only, use the first eight characters on the chart. Example: If a 0.25 inch Tee 4/600# ANSI Flange RJ fitting made of Duplex SS is required, use part TS51350000. To order a Body with a Plug Assembly, use the first eight characters on the chart. Example: If a Flarweld mount with a 0.75 Tee body style and pipeline size of 4 inch, made with a body material of ASTM A105 Carbon Steel is needed, with a Solid CS Plug, a Hydrin O-Ring Teflon packing, use part #TS13321550. To order a body with a Plug Assembly and a Cover, use all nine characters on the chart. Example: #TS133215511
2.
3.
Non Tee Type Access Fittings
Model Flarweld Buttweld Socketweld NPT
Height (in) 5.25 5.25 6.25 6.25
Weight (lbs) 5.5 5.5 4.5 4.5
Flange Size 150 300 4/600 9/1500 2.500 Temperature Rating --Pressure Rating ---
Height (in) 5.25 5.25 6.25 6.25 6.25 -20oF (28.9oC) to +350oF 176.6oC 6000PSI or as Flange Size
Weight (lbs) 10.5 11.5 15.25 30.75 40
Tee Type Access Fittings
0.25 inch T Height (ins) 5.25 Weight (lbs) 4.5
1 inch T Height (ins) 7.25 Weight (lbs) 7
0.25 inch T Model Flange Size 150 300 4/600 9/1500 2500 150 300 4/600 9/1500 2500 2000# 3/5000# 10000# Height (ins) 5.25 5.25 6.25 6.25 6.25 5.25 5.25 6.25 6.25 6.25 6.25 6.25 6.25 Weight (lbs) 9.75 11.50 12.75 25.75 40.20 9.75 11.50 12.75 25.75 40.10 15.75 31.00 40.50
0.5 inch T Height (ins) 7.25 7.25 7.25 8.25 8.25 7.25 7.25 7.25 8.25 8.25 7.25 8.25 8.25 Weight (lbs) 10.00 11.75 13.00 26.00 40.50 9.75 10.00 11.75 25.75 40.10 18.00 38.00 45.50
0.75 inch T Height (ins) 7.25 7.25 7.25 8.25 8.25 7.25 7.25 7.25 8.25 8.25 7.25 8.25 8.25 Weight (lbs) 10.00 12.00 13.00 26.25 40.40 13.00 17.00 18.00 38.00 45.50 18.00 38.00 45.50
1 inch T Height (ins) 7.25 7.25 7.25 8.25 8.25 7.25 7.25 7.25 8.25 8.25 7.25 8.25 8.25 Weight (lbs) 10.50 12.00 13.00 26.50 40.75 13.00 17.00 18.00 38.00 45.50 18.00 38.00 45.50
ANSI Flange RF
ANSI Flange RJ
API Flange
Two-Inch System Accessories
ACCESSORIES CONTINUE ON THE NEXT PAGE

PROTECTIVE COVERS Application Description Cover with 0.5 inch NPT Hole Cover with Hole Cover without Hole Cover with Hole Cover without Hole Cover and Bleed Valve Cover, Bleed Valve and Pressure Gauge Part No.
Material
Continuous Monitoring with pressure retaining seal and 0.5 inch NPT hole for permanent probe adaptor Continuous Monitoring Intermittent Monitoring - Chemical Injection Continuous Monitoring Intermittent Monitoring Provides a secondary seal in case of leaks Similar to P.N 700480
700731 1022 C.S. 700732 1022 C.S. 700734 1022 C.S. 700435 Polycarbonate 700436 Polycarbonate 700480 1022 C.S. 700481 CS/316 SS 700482 CS/316 SS
Provides a secondary seal whilst permitting Cover, Bleed Valve Pressure continuous monitoring - not for use above Gauge and 0.5 inch NPT Hole 4000 PSI SERVICE EQUIPMENT Application Description
Part No. Material 700111 700112 700113 700114 700115 700116 700117 700118 M2 Steel M2 Steel . . . . . .
Maintenance of threads in the Access Fitting Thread Tap Assembly Body Maintenance of threads on the Solid and Hollow Plug Bodies Removal of rust, scale etc. from the plug seat in the Access Fitting Body For the removal of debris from the Access Fitting Body threads Thread Die Assembly Seat Reamer Thread brush
Maintenance of the 3 inch Acme Thread on 3 inch Acme Thread Cleaner the Access Fitting Body Multi Purpose Grease For use in light hydrocarbon liquids Lithium Grease Silicone Grease
For cleaning sand and debris from the Access Fitting Body Threads before Cleaning Tube Assembly installation of Solid and Hollow Plugs under pressure

Seal and "O" Rings
Temperature Range
+45 C to +176 +C -50o F to +350o+F Steam to +450 F +250C +350 +F to +500 +F +176 +C to +260 +C In Excess of 500 F 287C
o o o o
Material
"O" Ring, Viton Primary Packing, Teflon "O" Ring, Ethylene Propylene Primary Packing, Vespel "O" Ring, Kalrez or Chemraz Silicone Primary Packing, Vespel Primary Packing, Nitronic 60 Do not use "O" rings at these temperatures.
Part Number
700600 700266 700139 700773 700680 700601 700733 700284

Two-Inch System Retriever and Service Valve Kits
The Retriever and Service Valve permit safe and simple removal of a range of monitoring probes and chemical injection devices whilst the pipeline or vessel is under operating pressure. The retrieval tool has been designed to operate on the principal of balancing the pressure acting on the internal surfaces of the tool so that no resultant force is applied to the retriever moving parts whilst the equipment is being operated. Retriever tools are sized to accommodate different pipeline pressures and probe/device lengths. All the materials of construction comply with the requirements of NACE standard MR-0175 (92). Service Valves are lightweight, portable 2 inch ball valve type which, interface the retriever to the Two Inch System Access Fitting. The valve also contains the line pressure whilst the Retriever and Access Fitting Plug Assembly are removed from the system. Service Valves are supplied with two bleed valves. One valve bleeds to atmosphere, allowing pressure within the retriever/valve system to be released. The second valve bleeds pressure from the outlet (line) to the inlet (retriever) side of the valve. This makes operation of the valve quite easy, as the valve seats are not under load. Retriever and Service Valve Kits include a heavy duty carrying case, maintenance tools and spare seals. A comprehensive Operation and Maintenance Manual is also included. Seal and Repair Kits are available separately at a moderate cost. Operator training is minimal and is easily achieved once the basic principles of operation are understood. Training courses are available both on-site and off-site as required.
Total Length Pressure Rating/Part Numbers Stroke Max Probe Clearance mm Length mm Collapsed Extended 100 Bars 250 Bars 400 Bars 450 200 648 1,108 1,362 700501 700601 700801 630 406 826 1.463 1.713 700502 700602 700802 830 612 1.004 1,818 2,073 700503 700603 700803 940 711 1.130 2.073 2.323 700504 700604 700804 1.224 1.016 1.435 2.683 2.957 700505 700605 700805 1.530 1.320 1.740 3.292 3.546 700506 700606 700806 These maximum probe dimensions are only valid with 5.25 inch Flarweld and Buttweld Access Fittings. For maximum probe length with other Access Fitting configurations contact our sales office. HOW TO ORDER 1. Retrievers are selected by the length of stroke required. The stroke is the distance the Plug Assembly and Probe must travel from within the Access Fitting body, through the Service Valve allowing the valve to be closed. 2. From figure A determine the Retriever stroke length required to retrieve the maximum length probe. Spare Parts Options Part Number Description Part Number Description 700084 Retriever Seal Kit 700674 Divertor Hose Assembly - 3M 700085 Retriever Repair Kit 700676 Divertor Hose Assembly - 8M 700047 Safety Hammer 700677 Divertor Hose Assembly - 15M 700066 Head Bar 700678 Surge Tube Assembly 700060 Retainer Clamp 700752 Field Operators Tool Kit

Two-Inch System Service Valve Kits
Service valves are required to connect the retriever tool to the Access Fitting to be serviced; its primary function is to contain the line pressure whilst the monitoring probe/injection device is replaced or removed. Designed for ease of use in connection with a Retriever Tool, Service Valves are ball type valves with full opening port and feature two Bleed Valves which permit easier operation at high pressures. One valve allows pressure equalisation on both sides of the valve, thus allowing the valve to be opened without torque problems. The second valve allows pressure or product to be bled to atmosphere or for product sampling. Service Valves are available rated for 250 Bar (3600psi) and 400 Bar (5700psi). Service Valves rated 250bar are extremely compact with a total weight of 7 kilos. ALL SERVICE VALVES COMPLY WITH NACE MR-01-75 (92 Rev) REQUIRMENTS FOR MATERIALS SUITABLE FOR USE IN SOUR SERVICE CONDITIONS. How to order:

Service Valve Kit - 250 Bar - Part No 700187 Service Valve Kit - 400 Bar - Part No 700191 SPARE PARTS Material 700051 700052 700053 700054
Description Service Valve Repair Kit Service Valve Seal Kit Service Valve Repair Kit Service Valve Seal Kit
250 Bar (3600 psi) 250 Bar (3600psi) 400 Bar (5700psi) 400 Bar (5700psi)

Hot Tap Tool
The Hot Tap Tool provides a safe and reliable method of hot tapping high pressure access fittings on presented pipelines or vessels. OPERATION A Special cutter assembly is installed in the access fitting previously welded onto the pipe. To tap a hole through the pipe wall, a service valve is installed on to the fitting. This allows the cutter fitting to be isolated if necessary. The hot tap tool is mounted onto the service valve and mated to the cutter. The drive screw on the hot tap tool puts pressure onto the cutter as the tool shaft is rotated to cut through the pipe wall. After the hole is cut through the pipe wall, the tool is removed from the valve and the retrieval tool is then used to pull the cutter assembly and pipe plug from the fitting. Shavings and cuttings are removed using swabs or brushes. The hot tap procedure may be expedited by the use of an air operated drill motor to turn the cutter shaft. Safety is enhanced because the cutter is isolated from the atmosphere by a service valve. At any time in the procedure the cutter drive shaft may be retracted and the fitting and its contents isolated from the atmosphere by closing the service valve. The hot tap tool is compatible with other major manufacturer's access fitting assemblies. Part HA102102 Components Description Bore Reamer Assembly HP Thread Chaser with Adaptor Seat Reaming Assembly Weld and Seal Test Fixture Cutter Assembly - HP 5.25 Nipple HP Cutter Test for CT Cutter Test Assembly Bushing Insertion Tool Hot Tap and Extraction Tool Test Assembly Hot Tap Turning Handle Over shot for Cutter Part Number 102004 8002 7282A 8004 7305G 7306A 7241A 7307A 7308A 7244A
Adaptor for Tools Magnetic Swab Assembly 3/16" Allen Wrench Spanner Wrench 1" Hex Socket Snap Ring Pliers Seal Insertion Ring Brass Hammer 3/32" Allen Wrench Snap Ring Pliers Quick Coupling (female) " Drive, socket "T" Handle Case Seal Repair Kit
102001158 102003 PR6352 PR6356 PR6433 PR2283 7249A PR6358 PR2291 PR2297 PR1294 PR6357 PR2399 7213A
The above tools are furnished as standard equipment with each complete Hot Tap Tool Kit. In addition common tools such as 3/16" Punch, large Crescent Wrench, large Screw Driver may be necessary.
HYDRALIC RETRIEVER AND SERVICE VALVE KIT MODEL HPH

The Model HPH Hydraulic Retriever Tool is a single cylinder retriever of fixed length which is equilibrated at the same pressure as the pipeline or vessel to be serviced. An internal piston may be moved up or down by changing the pressure in the upper barrel of the retriever. Pressure differential of a few PSI is sufficient to move the piston. Downward movement is obtained by pumping oil into the upper part of the retriever using a small portable pump; upward motion is achieved by returning oil to the oil tank. Internal safety devices are provided to prevent excessive pressure differentials from being developed across the piston. A Socket Adaptor Assembly is attached to the Internal piston. A Pilot on this Adaptor mates the assembly to the standard Triseal 2 System Solid or Hollow plug. When the piston is moved to the lower part of the retriever it may be connected to the retriever barrel which is then turned to screw or unscrew the Plug Assembly from the Triseal access fitting body.
MINIMUM CLEARANCE REQUIREMENTS, MINIMUM WEIGHT AND FULL COMPATIBILITY WITH ALL GENERIC ACCESS FITTINGS ARE MAJOR FEATURES OF THE HPH RETRIEVER TOOL
Triseal is the Registered Tradename of Rose Corrosion Services Limited
HPH Retriever Ordering Information

250 Bar Maximum Working Pressure
Retriever Kit Part Number Maximum Probe Length Removal Clearance Retriever Cylinder Length Retriever Weight Retriever Kit Weight 700834 130mm 5.11 840mm 510mm 15.75 kg 46.50 kg 700835 200mm 7.87 945mm 615mm 17.20 kg 48.00 kg 700836 300mm 11.81 1096mm 765mm 18.70 kg 49.50 kg 700837 400mm 15.74 1245mm 915mm 20.50 kg 51.50 kg 700838 500mm 19.68 1395mm 1065mm 22.01 kg 53.50 kg 700839 600mm 23.62 1545mm 1215mm 23.70 kg 55.50 kg 700840 700mm 27.55 1695mm 1365mm 25.60 kg 58.00 kg 700841 800mm 31.50 1845mm 1515mm 27.70 kg 60.50 kg 700842 900mm 35.43 1995mm 1665mm 29.85 kg 64.00 kg
450 Bar Maximum Working Pressure

Retriever Kit Part Number Maximum Probe Length Removal Clearance Retriever Cylinder Length Retriever Weight Retriever Kit Weight
701100 130mm 5.11 840mm 510mm 20.75 kg 54.50 kg
701101 200mm 7.87 945mm 615mm 22.20 kg 56.00 kg
701102 300mm 11.81 1096mm 765mm 23.70 kg 57.50 kg
701103 400mm 15.74 1245mm 915mm 25.50 kg 59.50 kg
701104 500mm 19.68 1395mm 1065mm 27.01 kg 61.50 kg
701105 600mm 23.62 1545mm 1215mm 28.70 kg 63.50 kg
701106 700mm 27.55 1695mm 1365mm 31.60 kg 64.00 kg
701107 800mm 31.50 1845mm 1515mm 32.70 kg 68.50 kg
701108 900mm 35.43 1995mm 1665mm 39.85 kg 72.00 kg
HOW TO ORDER: 1. Retriever size is determined by the length of piston movement required within the retriever cylinder. This is the distance the plug assembly and probe must travel from within the access fitting body and through the service valve allowing the valve to be closed. 2. Determine the maximum working pressure required 3. Determine the maximum probe length required to be retrieved. 4. From the above table select the most suitable kit Part Number. Order by Kit Part Number. SPARE PARTS 250 Bar Description Retriever Seal Kit Service Valve Seal Kit Hydraulic Pump Three Way Valve Part Number 700868 700877 700842 700844 450 Bar Description Retriever Seal Kit Service Valve Seal Kit Hydraulic Pump Three Way Valve Part Number 701109 701110 701111 701112

Product Catalogue

Uploaded by

Copyright:

Available Formats

Product Catalogue

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Product Catalogue

Uploaded by

Copyright:

Available Formats

BACK TO MAIN MENU

BACK TO MAIN MENU

BACK TO MAIN MENU

BACK TO CORROSION MONITORING MENU

BACK TO CORROSION MONITORING MENU

BACK TO CORROSION MONITORING MENU

BACK TO CORROSION MONITORING MENU

ROSE CORROSION SERVICES LIMITED

BACK TO ELECTRICAL RESISTANCE MENU

SCROLL DOWN FOR SECOND PAGE

ROSE CORROSION SERVICES LIMITED

Technical Specifications E/R Probe Configurations:

Dimensions with Leather Case:

Height: Width: Depth:

4.4 inches (11.2cms) 9.0 inches (22.9cms) 8.0 inches (20.3cms)

Dimensions without Leather Case:

Height: Width: Depth:

Weight with Leather Case:

Operational Humidity Range: 30% to 90% Storage Humidity Range: 5% to 95%

Length of Connecting Cable: 6 feet (2 metres) Intrinsic Safety:

BACK TO ELECTRICAL RESISTANCE MENU

ROSE CORROSION SERVICES LIMITED

MS1500E Corrosion Meter

BACK TO ELECTRICAL RESISTANCE MENU

SCROLL DOWN FOR SECOND PAGE

ROSE CORROSION SERVICES LIMITED

BACK TO ELECTRICAL RESISTANCE MENU

ROSE CORROSION SERVICES LIMITED

BACK TO ELECTRICAL RESISTANCE MENU

SCROLL DOWN FOR SECOND PAGE

ROSE CORROSION SERVICES LIMITED

Intrinsic Safety: Part #:

BACK TO ELECTRICAL RESISTANCE MENU

ROSE CORROSION SERVICES LIMITED

MS3500E Data Logger

BACK TO ELECTRICAL RESISTANCE MENU

SCROLL DOWN FOR SECOND PAGE

ROSE CORROSION SERVICES LIMITED

BACK TO ELECTRICAL RESISTANCE MENU

ROSE CORROSION SERVICES LIMITED

Epoxy 250 F/121 C 4 or 8 mils (useful range is half of thickness)

BACK TO ELECTRICAL RESISTANCE MENU

SCROLL DOWN FOR SECOND PAGE

ROSE CORROSION SERVICES LIMITED

BACK TO ELECTRICAL RESISTANCE MENU

ROSE CORROSION SERVICES LIMITED

BACK TO ELECTRICAL RESISTANCE MENU

SCROLL DOWN FOR SECOND PAGE

ROSE CORROSION SERVICES LIMITED

BACK TO ELECTRICAL RESISTANCE MENU

ROSE CORROSION SERVICES LIMITED

BACK TO ELECTRICAL RESISTANCE MENU

SCROLL DOWN FOR SECOND PAGE

ROSE CORROSION SERVICES LIMITED

BACK TO ELECTRICAL RESISTANCE MENU

ROSE CORROSION SERVICES LIMITED

STD. LENGTH 8" 12" 18"

BACK TO ELECTRICAL RESISTANCE MENU

SCROLL DOWN FOR SECOND PAGE

ROSE CORROSION SERVICES LIMITED