PG738EX-961212-0004

SOFTWARE VERSION 3.10 CONTROL PANEL RESET:

Installer lock must be unlocked. (Address 058: enter any value other than 147)
Power down reset (1) Remove battery and AC to power down the unit. (2) Connect a jumper between "reset jumper" pins. (3) Connect AC then the battery. (4) Wait 10 seconds. (5) Remove jumper. Factory default installer and master codes will be reinstated. Values entered at addresses 008-043, 062-126 and 300-527 as well as all user codes, will be erased ([2ND] [2ND]). Programmed values of all other addresses do not change.

HEXA PROGRAMMING:
All digits from 0 to F are valid. Values are programmed into memory locations from address 000 to 043 and from address 300 to 527. 1) Press [ENTER] + installer code. 2) [ENTER] will flash (programming mode). 3) Enter 3 digit memory address. 4) Current value will be displayed on keypad. 5) Enter 2 digit data. 6) Go to step 3 for next address. To exit programming mode, press [CLEAR].
HEXA DISPLAY
If key is lit = 8

= 4

Value of 2ND digit = 10 ( 8 + 2 = 10) Value of 1ST digit = 3 ( 2 + 1 = 3) VALUE = "3A"

No light = 0

If key is lit = 8 =

No display = SKIP (empty) 10 = [0] = [A]

STREAMLINED SECTION PROGRAMMING

Can be used to program sections 00 to 67. (addresses 000 to 043 and 300 to 527) Press [ENTER], installer code, and [7]. ([2ND] and [ENTER] keys alternately flash.) Enter a 2-digit section number, followed by 8 digits to program that section (confirmation beep). Data will be saved automatically and the software advances to the next programming section. To exit programming mode press [CLEAR]. (addresses 000, 001, 002) SECTION 00 Full access to programming, except access codes. (addresses 127-299) No access to arming/disarming. Can be used to modify installer code. Use only numeric keys from [1] to [10]. (key [10] = 0)

INSTALLER CODE: (reset code 737373)

PANEL ANSWER OPTIONS: (address 003) SECTION 00 First digit disables Answering Machine Override (key [2ND] or key [1]), or determines period of time between first and second call (see table below). Second digit determines number of rings required before panel will answer. If [2ND][2ND] is entered, panel will not answer. (Default value is [2ND] [8].)

-1-

PG738EX

TELEPHONE AND ACCOUNT NUMBERS: (reset empty)

If only one central station phone number is used, program the same number for telephone number 1 and 2.

[10] [11] [12]

= the number "0" =* =#

[BYP] [MEM] [TRBL]

= switch from pulse to tone while dialing = pause 4 seconds = end of number

COMPUTER TELEPHONE NUMBER: (View at addresses 008 to 015.)

Streamline section
1 2 3 4 5 6 7 8

Streamline section

02 __ / __ / __ / __ / __ / __ / __ / __

03 __ / __ / __ / __ / __ / __ / __ / __
9 10 11 12 13 14 15 16

Press [TRBL] to end phone number if less than 16 digits are programmed.

CENTRAL STATION TELEPHONE NUMBER 1: (View at addresses 016 to 023.)

Streamline section
1 2 3 4 5 6 7 8

Streamline section

04 __ / __ / __ / __ / __ / __ / __ / __

05 __ / __ / __ / __ / __ / __ / __ / __
9 10 11 12 13 14 15 16

Press [TRBL] to end phone number if less than 16 digits are programmed.

CENTRAL STATION TELEPHONE NUMBER 2: (View at addresses 024 to 031.)

Streamline section
1 2 3 4 5 6 7 8

Streamline section
9 10 11 12 13 14 15 16

06 __ / __ / __ / __ / __ / __ / __ / __ 07 __ / __ / __ / __ / __ / __ / __ / __

Press [TRBL] to end phone number if less than 16 digits are programmed.

ACCOUNT "A" AND "B": (View at addresses 032 to 035.)

Streamline section

For 3 digit account numbers, enter "skip" ([2ND]) as first digit.

08 ___ / ___ / ___ / ___

1 2 3 4

___ / ___ / ___ / ___

5 6 7 8

If only one account number is required, the same number must be entered for both account "A" and "B".

-2-

PG738EX

Streamline section

Data

Description

Address
036 037 038 039
TIME CORRECTION:
(address 037 second digit) [2ND] - No adjustment [1] - Plus 4 sec. [2] - Plus 8 sec. [3] - Plus 12 sec. [4] - Plus 16 sec. [5] - Plus 20 sec. [6] - Plus 24 sec. [7] - Plus 28 sec. [8] - Minus [9] - Minus [10] - Minus [11] - Minus [12] - Minus [BYP] - Minus [MEM] - Minus [TRBL] - Minus 4 sec. 8 sec. 12 sec. 16 sec. 20 sec. 24 sec. 28 sec. 32 sec.

[2 ND] [2ND] Future use ___/___ [2 ND] ___/___ 1st digit: value must be entered i.e. [2ND]

09

___/___ ___/___

2nd digit: time correction (See table) 1st digit: telephone 1 format 2nd digit: telephone 2 format 1st digit: PGM 1 type 2nd digit: PGM 2 type

10

___/___ ___/___ ___/___ ___/___

PGM 1 PGM 2 PGM mask 1 PGM mask 2

040 041 042 043

COMMUNICATOR FORMATS Key [2ND] = ADEMCO slow (1400Hz, 1900Hz, 10bps) [1] = (1400Hz, 1800Hz, 10bps) [2] = SILENT KNIGHT fast (1400Hz, 1900Hz, 20bps) [3] = SESCOA (2300Hz, 1800Hz, 20bps) [4] = RADIONICS (40bps with 1400Hz handshake) [5] = RADIONICS (40bps with 2300Hz handshake)

= RADIONICS with PARITY (1400Hz, 40bps) = RADIONICS with PARITY (2300Hz, 40bps) = ADEMCO express = ADEMCO contact ID (programmable codes) = ADEMCO contact ID (all codes) [TRBL] = DTMF - no handshake (personal dialing)

[6] [7] [8] [9] [10]

PROGRAMMABLE CONTACT ID EVENT CODES

All addresses from 300 to 527 (sections 11 to 67) programmed with values other than [2ND] [2ND] will report the contact ID codes corresponding to the values programmed. Values to be programmed should be selected from this table.
CID
100: 110: 111: 112: 113 114: 115: 116: 117: 118: 120: 121: 122: 123: 130: 131: 132: 133: 136: 137: 138: 140: 150: 151: 152: 153: 154: 155: 156: 157: 158: 159: 161:

REPORTING CODE
AUXILIARY ALARM FIRE ALARM FIRE SMOKE COMBUSTION WATER FLOW HEAT PULLSTATION DUCT FLAME NEAR ALARM PANIC ALARM DURESS SILENT PANIC AUDIBLE PANIC BURGLARY PERIMETER BURG. INTERIOR BURG. 24HR BURGLARY BURGLARY OUTDOOR BURGLARY TAMPER BURGLARY NEAR ALARM GENERAL ALARM 24 HOUR AUX GAS DETECTED REFRIGERATION LOSS OF HEAT WATER LEAKAGE FOIL BREAK ALARM DAY TROUBLE ALARM LOW GAS LEVEL HIGH TEMPERATURE LOW TEMPERATURE LOSS AIR FLOW

PROG. VALUE
[2ND] / [1] [2ND] / [2] [2ND] / [3] [2ND] / [4] [2ND] / [5] [2ND] / [6] [2ND] / [7] [2ND] / [8] [2ND] / [9] [2ND] / [10] [2ND] / [11] [2ND] / [12] [2ND] / [BYP] [2ND] / [MEM] [2ND] / [TRBL] [1] / [2ND] [1] / [1] [1] / [2] [1] / [3] [1] / [4] [1] / [5] [1] / [6] [1] / [7] [1] / [8] [1] / [9] [1] / [10] [1] / [11] [1] / [12] [1] / [BYP] [1] / [MEM] [1] / [TRBL] [2] / [2ND] [2] / [1]

CID
300: 301: 302 305: 306: 309: 320: 321: 323: 350: 351: 354: 370: 371: 372: 373: 382: 383: 400: 401: 402: 403: 404: 407: 410: 441: 570: 572: 573: 574: 601: 602: 625:

REPORTING CODE
SYSTEM TROUBLE AC LOSS LOW SYSTEM BATTERY SYSTEM RESET PROGRAM CHANGED BATTERY TEST FAIL SOUNDER/RELAY TROUBLE BELL 1 TROUBLE ALARM RELAY TROUBLE COMMUNICATION TROUBLE TELCO 1 FAULT FAIL TO COMMUNICATE PROTECTION LOOP TROUBLE PROTECTION LOOP OPEN PROTECTION LOOP SHORT FIRE LOOP TROUBLE SENSOR TROUBLE SENSOR TAMPER OPEN/CLOSE OPEN/CLOSE BY USER # GROUP OPEN/CLOSE AUTOMATIC OPENING/CLOSING LATE TO OPEN/CLOSE REMOTE ARM DOWNLOAD REMOTE ACCESS OPEN/CLOSE - STAY MODE BYPASS 24 HOUR ZONE BYPASS BURGLARY BYPASS # GROUP BYPASS MANUAL TEST PERIODIC TEST TIME/DATE RESET

PROG. VALUE
[2] / [2] [2] / [3] [2] / [4] [2] / [5] [2] / [6] [2] / [7] [2] / [8] [2] / [9] [2] / [10] [2] / [11] [2] / [12] [2] / [BYP] [2] / [MEM] [2] / [TRBL] [3] / [2ND] [3] / [1] [3] / [2] [3] / [3] [3] / [4] [3] / [5] [3] / [6] [3] / [7] [3] / [8] [3] / [9] [3] / [10] [3] / [11] [3] / [12] [3] / [BYP] [3] / [MEM] [3] / [TRBL] [4] / [2ND] [4] / [1] [4] / [2]

For addresses 044 to 126, see pages 7 to 10.

-3-

PG738EX

REPORTING CODES: (reset code = empty"

[2ND] [2ND]) All digits from [1] to [F] are valid. Enter [2ND] (skip) = digit will not be reported except for contact I.D. programmable codes. For single digit reporting enter "skip" ([2ND]) as first digit.

If CONTACT I.D. format (all codes) is selected, addresses 300 to 527 (sections 11 to 67) do not have to be programmed. (Select Contact I.D (all codes) - key [10] for both central station numbers at section 09 - address 038.)

ARMING (closing) CODES:

Streamline section Data
___/___ ___/___ ___/___ ___/___

Description
Auto / Espload Master User code 1 User code 2

Address
300 301 302 303

Streamline section

Data
___/___ ___/___ ___/___ ___/___

Description
User code 27 User code 28 User code 29 User code 30

Address
328 329 330 331

11

18

12

___/___ ___/___ ___/___ ___/___

User code 3 User code 4 User code 5 User code 6

304 305 306 307

19

___/___ ___/___ ___/___ ___/___

User code 31 User code 32 User code 33 User code 34

332 333 334 335

13

___/___ ___/___ ___/___ ___/___

User code 7 User code 8 User code 9 User code 10

308 309 310 311

20

___/___ ___/___ ___/___ ___/___

User code 35 User code 36 User code 37 User code 38

336 337 338 339

14

___/___ ___/___ ___/___ ___/___

User code 11 User code 12 User code 13 User code 14

312 313 314 315

21

___/___ ___/___ ___/___ ___/___

User code 39 User code 40 User code 41 User code 42

340 341 342 343

15

___/___ ___/___ ___/___ ___/___

User code 15 User code 16 User code 17 User code 18

316 317 318 319

22

___/___ ___/___ ___/___ ___/___

User code 43 User code 44 User code 45 User code 46

344 345 346 347

16

___/___ ___/___ ___/___ ___/___

User code 19 User code 20 User code 21 User code 22

320 321 322 323

23

___/___ ___/___

User code 47 User code 48 / (Duress)

348 349

See next page

17

___/___ ___/___ ___/___ ___/___

User code 23 User code 24 User code 25 User code 26

324 325 326 327

-4-

PG738EX

REPORTING CODES:
Streamline section Data

(reset code "empty")

DISARMING (opening) CODES:

Description Address Streamline section Data
___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___

Description
User code 25 User code 26 User code 27 User code 28 User code 29 User code 30 User code 31 User code 32 User code 33 User code 34 User code 35 User code 36 User code 37 User code 38 User code 39 User code 40 User code 41 User code 42 User code 43 User code 44 User code 45 User code 46 User code 47 User code 48 / (Duress)

Address
376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399

See previous page

23

___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___

Espload Master User code 1 User code 2 User code 3 User code 4 User code 5 User code 6 User code 7 User code 8 User code 9 User code 10 User code 11 User code 12 User code 13 User code 14 User code 15 User code 16 User code 17 User code 18 User code 19 User code 20 User code 21 User code 22 User code 23 User code 24

350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375

30

24

31

25

32

26

33

27

34

28

35

29

ALARM CODES ZONE 1 TO 12:

Streamline section Data
___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___

ALARM CODES ZONE 13 TO 24:

Address Streamline section Data
[ 2ND] [2ND] ___/___

Description
Zone 1 Zone 2 Zone 3 (fire) Zone 4 Zone 5 Zone 6 Zone 7 Zone 8 Keypad 1 Zone 9 Keypad 2 N/A N/A N/A

Description
N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A

Address
412 413 414 415 416 417 418 419 420 421 422 423

36

400 401 402 (see add. 100) 403 404 405 406 407 408 409 410 411

39

[ 2ND] [2ND] ___/___ [2 ND] [ 2ND] /_ ___ __ [ 2ND] [2ND] ___/___ [ 2ND] [2ND] ___/___

37

40

[ 2ND] [2ND] ___/___ [2ND] [ 2ND] /___ ___ [ 2ND] [2ND] ___/___ [ 2ND] [2ND] ___/___

38

[ 2ND] [2ND] ___/___ [2ND] [ 2ND] /___ ___ [ 2ND] [2ND] ___/___

41
-5-

[ 2ND] [2ND] ___/___ [2ND] [ 2ND] /___ ___ [ 2ND] [2ND] ___/___

PG738EX

REPORTING CODES:
Streamline section Data
___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___

(reset code "empty")

ZONE 1 TO 12 RESTORE CODES:

Description
Zone 1 Zone 2 Zone 3 (fire) Zone 4 Zone 5 Zone 6 Zone 7 Zone 8 Keypad 1 Zone 9 Keypad 2 N/A N/A N/A

ZONE 13 TO 24 RESTORE CODES:

Address Streamline section Data
[___/___ 2ND] [2ND]

Description
N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A

Address
436 437 438 439 440 441 442 443 444 445 446 447

42

424 425 426 (see add. 100) 427 428 429 430 431 432 433 434 435

45

[___/___ 2ND] [2ND] [2__ ND] [___ 2ND] /_ [___/___ 2ND] [2ND] [___/___ 2ND] [2ND]

43

46

[___/___ 2ND] [2ND] [2ND] [___ 2ND] /___ [___/___ 2ND] [2ND] [___/___ 2ND] [2ND]

44

[ 2ND] [2ND] ___/___ [2ND] [ 2ND] /___ ___ [ 2ND] [2ND] ___/___

47

[___/___ 2ND] [2ND] [2ND] [___ 2ND] /___ [___/___ 2ND] [2ND]

ZONE 1 TO 12 SHUTDOWN CODES:

Streamline section Data
___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ [2ND] [2ND] ___/___ [2ND] [2ND] /___ ___ [2ND] [ 2 ND ] ___/___

ZONE 13 TO 24 SHUTDOWN CODES:

Streamline section Data
[___/___ 2ND] [2ND]

Description
Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 7 Zone 8 Keypad 1 Zone 9 Keypad 2 N/A N/A N/A

Address
448 449 450 451 452 453 454 455 456 457 458 459

Description
N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A

Address
460 461 462 463 464 465 466 467 468 469 470 471

48

51

[___/___ 2ND] [2ND] [2__ ND] [___ 2ND] /_ [___/___ 2ND] [2ND] [___/___ 2ND] [2ND]

49

52

[___/___ 2ND] [2ND] [2ND] [___ 2ND] /___ [___/___ 2ND] [2ND] [ 2ND] [2ND] ___/___

50

53

[___/___ 2ND] [2ND] [2ND] [ 2ND] /___ ___ [___/___ 2ND] [2ND]

TAMPER 1 TO 12 TROUBLE CODES:

Streamline section Data
___/___ ___/___ ___/___ ___/___ ___/___ ___/___ ___/___ [ 2ND] [2ND] ___/___
[2ND] [2ND] ___/___ [2ND] [2ND] ___/___ [2ND] [2ND] /___ ___ [2ND] [2ND] ___/___

TAMPER 13 TO 24 TROUBLE CODES:

Streamline section Data
[ 2ND] [2ND] ___/___

Description
Tamper 1 Tamper 2 Tamper 3 Tamper 4 Tamper 5 Tamper 6 Tamper 7 N/A N/A N/A N/A N/A

Address
472 473 474 475 476 477 478 479 480 481 482 483

Description
N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A

Address
484 485 486 487 488 489 490 491 492 493 494 495

54

57

[ 2ND] [2ND] ___/___ [2__ ND] [ 2ND] /_ ___ [ 2ND] [2ND] ___/___ [ 2ND] [2ND] ___/___

55

58

[ 2ND] [2ND] ___/___ [2ND] [ 2ND] /___ ___ [ 2ND] [2ND] ___/___ [___/___ 2ND] [2ND]

56

59
-6-

[___/___ 2ND] [2ND] [2ND] [___ 2ND] /___ [___/___ 2ND] [2ND]

PG738EX

DECIMAL PROGRAMMING
3 Digit Decimal Value Programming
Used to program addresses 044 to 061. Values entered must contain 3 digits between "000" and "255". ([10] = 0) Decimal value programming: 1) Press [ENTER] + installer code. ([ENTER] key will flash.) 2) Enter 3 digit address (044 to 061). 3) Current value will be displayed on keypad. 4) Enter 3 digit DECIMAL value. 5) Repeat from step 2 onward for next address. To exit programming mode press [CLEAR]. 044: ___/___/___ (hours) Auto arm time (between "000" and "023") 045: ___/___/___ (minutes) Auto arm time (between "000" and "059") 046: ___/___/___ (days) Auto test report every ? days (between "001" and "255") (000 = disabled) 047: ___/___/___ (hours) Auto test report (between "000" and "023") 048: ___/___/___ (minutes) Auto test report (between "000" and "059")

-7-

PG738EX

DECIMAL PROGRAMMING
049: ___/___/___ (seconds) Exit delay (factory default 60 seconds) 050: ___/___/___ (seconds) Entry delay 1 (factory default 45 seconds) 051: ___/___/___ (seconds) Entry delay 2 (factory default 45 seconds) 052: ___/___/___ (minutes) Bell cut-off time (factory default 5 minutes) 053: ___/___/___ ( x 15 mSec.) Zone speed (factory default 600 mSec.) 054: ___/___/___ (minutes) Power failure report delay (factory default 30 minutes) (000 = disabled) 055: ___/___/___ ( x 15 minutes) "No movement" report time (factory default 8 hours) (000 = disabled) 056: ___/___/___ PGM timer setting (001 to 127 for seconds and 129 to 255 for minutes) (factory default 5 seconds) Add 128 to desired value in minutes (i.e. for 5 minutes: enter 5 + 128 = 133) 057: ___/___/___ Intellizone delay (in seconds, minimum = 10 seconds) (factory default 48 seconds) 058: ___/___/___ Installer code lock (147 = locked, 000 = unlocked) 059: ___/___/___ (seconds) Programmable delay before alarm transmission (5 to 63 seconds) (000 = disabled) 060: ___/___/___ (seconds) Recent closing delay (000 = disabled) 061: ___/___/___ Future Use

FEATURE SELECT PROGRAMMING

Addresses 062-126. "ON"/"OFF" status of the key lights determines feature selection. In programming mode, enter 3 digit memory address (062 to 126). To save entries, press [ENTER]. To exit programming mode press [CLEAR]. Reset = OFF for addresses 062 to 126.

Addresses 080 to 085 for future use.

-8-

PG738EX

FEATURE SELECT PROGRAMMING (continued)

(On/off status of key lights determines which feature is selected.)
KEY

086:
See "TLM" table PS1/Keyswitch = regular arm PS1/keyswitch arming Call back Auto arm on time Auto arm on no movement Pulse dialing Partitioning Silent zone/panic generates a silent alarm (1:2) Pulse Europe See "Reporting" table
N/A

OFF / ON [2ND] [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12]
[BYP] [MEM] [TRBL]
KEY

TELEPHONE LINE MONITOR

Address 086, Key [2ND] [1]
KEY

stay arm / System A enabled enabled enabled enabled Tone dialing (DTMF) enabled generates only a report (1:1.5) Pulse USA

[2ND] [1]
OFF OFF ON ON OFF ON OFF ON

TLM disabled TLM generates trouble only generates an alarm if armed silent alarm becomes audible

(address 086, key [9] has to be OFF)

REPORTING OPTIONS
Address 086, Key [11] [12]

N/A

KEY
[11] [12]
OFF OFF OFF ON ON OFF ON ON

TYPE

DIALING SEQUENCE (tel. No.)

Bell squawk on arm/disarm Auto zone shutdown

enabled enabled

088:
Automatic event buffer transmission Panic 1 (keys [1] & [3], PS1) Panic 2 (keys [4] & [6]) Panic 3 (keys [7] & [9]) Panic 1 silent (PS1) Panic 2 silent Panic 3 silent Key [10] regular arm Key [11] stay or system A arm 6 digit access codes Tamper Recognition Beep on exit delay Report zone restore on bell cut-off Zones with EOL (1K ) Always report disarm

Reporting disabled Regular reporting Split reporting: Alarms System report Double reporting

OFF / ON [2ND] [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12]
[BYP] [MEM] [TRBL]
KEY

1,2,1,2,1,2,1,2, fail to comm. 1,1,1,1,1,1,1,1, fail to comm. 2,2,2,2,2,2,2,2, fail to comm. 1,1,1,1,1,1,1,1, fail to comm., 2,2,2,2,2,2,2,2, fail to comm.

enabled enabled enabled enabled audible audible fire enabled enabled 4 digit

*On alarm, all reports are made to Tel. #1 until system is disarmed.
(Once disarmed, system reports are made to Tel. #2)

TAMPER / WIRE FAULT DEFINITIONS

Address 088, Key [10] [11]
KEY

SYSTEM ARMED
Alarm as per individual zone definitions
Always generate trouble and alarm, audible or silent as per individual zone definitions

[10] [11]
OFF OFF OFF ON ON OFF ON ON

SYSTEM DISARMED

enabled on zone closure no EOL only after alarm

Tamper supervision disabled No alarm, trouble code reported Silent alarm. Trouble and alarm codes reported Audible alarm. Trouble and alarm codes reported

**

090:
Exclude power failure from trouble display
N/A

OFF / ON [2ND] enabled [1] N/A

[2] [3]
[4]

* **

Exception: for 24 hour zones the tamper definition will follow the audible/silent alarm definition of the 24 hour zone. Silent zones will generate a silent alarm.

Auto arm = regular arm

N/A N/A N/A

stay / System A N/A

N/A N/A

[5] [6] [7] [8] [9] [10] [11] [12]

[BYP] [MEM] [TRBL]

No tamper bypass
N/A N/A

tamper follows zone bypass definition

N/A N/A

Audible trouble warning Duress Keypad 1 zone supervision Keypad 2 zone supervision
N/A N/A N/A

enabled enabled enabled enabled

N/A N/A N/A

PS1 software version 1.1 Keypad supervision must be OFF Keypad software versions prior to 4.0

} PS1 software versions 2.0 onward Keypad supervision must be ON Keypad software versions 4.0 onward}
(See Wiring Diagram)

-9-

PG738EX

Note: Do not use the Intellizone feature and an entry delay for the same zone, otherwise an alarm may occur as a user tries to disarm the system.

KEY ACCESS PROGRAMMING

Programs features quickly, without entering addresses or section numbers. To activate key access programming, press [ENTER], followed by installer, master or user code 1. (Code required depends on the feature you wish to access - see below.) Press the key corresponding to the desired feature. Press [ENTER] or [CLEAR] to exit.

key

[8]

Installer test mode (installer code only) In installer test mode, a confirmation beep (intermittent) indicates test is "on", a "rejection" beep (long) indicates test is "off". The bell will squawk during walk testing to indicate opened, functional zones. "Auto arming" time program (all 3 codes) Key [9] flashes. Enter two digits (00 to 23) for hours + 2 digits (00 to 59) for minutes. "Panel time" and clear "trouble 8" (all 3 codes) Key [MEM] flashes. Enter two digits (00 to 23) for hours + 2 digits (00 to 59) for minutes. Test report (all 3 codes) Reporting is enabled at address 086, keys [11], [12]. A value must be entered at address 512, and both telephone and account numbers must be programmed. Call Espload via telephone (all 3 codes) Panel identifier and PC password (addresses 004-007) and computer telephone number (addresses 008-015) must be programmed.

[9] [MEM] [BYP]

[TRBL]

[AWAY] Answer Espload

(all 3 codes) This feature is available when using the ADP-1 adapter. In Espload, "blind dial" must be activated in "modem setup" section, and panel phone number programmed (works also without ADP-1).
Cancel communication attempts Until next reportable event

[STAY]

(master code and user 1 can only stop calls to Espload) (installer code - all communications)

When communicating with Espload, it is impossible to enter programming mode.

- 10 -

PG738EX

ESPRIT 738 EXPRESS CONNECTION DIAGRAMS

The system hardware will recognize the following zone conditions: Note: Keypad zones always use (1K OHM) EOL resistor.

SINGLE ZONE CONNECTIONS

ZONE connection, without EOL resistor (N.C. contacts) address 088, key [MEM] = "on" key [10] = "off " (reset) key [11] = "off " (reset) N.C. contacts see Figure 1

ZONE connection, with EOL resistor (N.C. and N.O. contacts) address 088, key [MEM] = "off" (reset) key [10] = "off " (reset) key [11] = "off " (reset) N.C. and/or N.O. contacts, see Figure 2

ZONE connection, without EOL resistor, with tamper recognition (N.C. contacts) address 088, key [MEM] = "on" key [10] = See "Tamper/wire Fault Definitions and Options" key [11] = Tamper transmits separate code, see Figure 3

ZONE connection, with EOL resistor, with tamper recognition, and with wire fault (short circuit) recognition (N.C. contacts) address 088, key [MEM] = "off " key [10] = See "Tamper/wire Fault Definitions and Options" key [11] = Tamper/wire fault transmits separate code, see Figure 4

- 11 -

ESPRIT 738 EXPRESS WIRING DIAGRAM

Caution: Disconnect battery before replacing fuse.

Charging and battery test LED

(every 60 seconds)

Service Keypad

"TLM" LED: Short flash = OK Long flash = Fault

PARADOX SECURITY SYSTEMS
SERIAL OUTPUT

OFF = Disabled Constant = On Line

BATT
5 AMP
RESET JUMPER

+ AUX -

GRN YEL

Four pin connector can be used for quick installation of an Esprit keypad.
BLACK RED

+
BATT
SERVICE KEYPAD

RECHARGEABLE BATTERY

BELL RELAY OPTION

UL/ULC 12VDC / 7AH To cabinet and grounding rod

COM N.C. N.0.

AC

PG1 PG2

GRY

1K EOL

Smoke and heat detectors

YEL

UL: K12 model T16 V4O ULC: Frost model FTC 1637
Warning: Improper connection may result in damage to the system.

TRANSFO

* Zone 3 = Fire zone if zone

definition is "24 hour".

Address 100

GRN

16.5VAC 40VA

BELL OUTPUT

A.C. POWER

will shut down if current exceeds 3A.

+ BELL

BLK RED

GRN

BRN

RED

*PS1 software version 1.1

Keypad software versions prior to 4.0 Keypad supervision must be OFF

} PS1 software versions 2.0 onward Keypad software versions 4.0 onward } Keypad supervision must be ON 090 [11] [12]
(See Address , key

FIRE RESET
To program PGM1 to conduct 4 second smoke detector reset when [CLEAR] and [ENTER] are pressed simultaneously: Address 039 = [BYP] (first digit) Address 042 = [2ND] [6] Address 040 = [5] [10] Address 056 = [10] [10] [4]
Keyswitch can be used in parallel with keypad (Not on UL systems).

FIRE ALARM ZONE CONNECTIONS

* PGM maximum 50mA

*PGM

+
AUX Smoke detector

Z3

COM

+
Smoke detector

+
Smoke detector power supervision relay, 12VDC

1K EOL
RNG

Smoke detector must be 4 wire latching UL Falcon model 5454, ULC BRK 2412. Power supervision relay model MR3-UL.

S E C U R I T Y

S Y S T E M S

780 Industrial Blvd., St-Eustache, Montreal, Quebec, Canada J7R 5V3 Fax: (514) 491-2313 http://www.paradox.ca

+
+
+ BELL

ESPRIT 738 EXPRESS

DIALER

Warning: Disconnect telephone line before servicing.

RJ31X CA 38A

AUX

GRN YEL

R - 1 T - 1 RING TIP

N.O. contacts

* ZONE 8 or 9
N.O.

SIREN

+ AUX POWER 400mA max. 250mA max. for 24 hr. standby. To connect additional wiring to auxiliary power, use the red (+) and black (-) keypad connectors. Aux power will shut down if current exceeds 1A.
ZONE 8 or 9
N.O.

1K EOL

UL/ULC Wheelock 46T-12

N.C.

KEYPAD
639/640
MAX 2 per system
P R
RMED
RE DY

KEYPAD
616/626/633
MAX 5 per system

1K EOL

N.C.

DOX

MAX 5 per system

PS1
1K EOL

The 640 keypad can be used with the panels but will not display correct event list codes.
N.C. N.C.

For resistor values, refer to 639/640 installation manuals.

ZONE 8

ZONE 9

KEYSWITCH CONNECTION
220
KYPD GRN
KEYSWITCH

KYPD BLK

GROUND START CIRCUIT

PGM OUTPUT RELAY

PGM WHT BLK RED

+AUX WHT BLK

PGM

+AUX

RED

MR3-UL
YEL

MR3-UL
BRN COM YEL

N.C. N.O.

Paradox Security Systems Graphic Dept PRINTED IN CANADA