JTA Light Weight Bevel Gearbox, Light Duty Bevel Gearbox, Smallest Aluminum 1 to 1 Ratio Miter Gearbox,Miniature Right Angle Gearbox,Micro Size Spiral Bevel Gearbox,Small 90 Degree Gearbox Catalogue
JTA Light Weight Bevel Gearbox, Light Duty Bevel Gearbox, Smallest Aluminum 1 to 1 Ratio Miter Gearbox,Miniature Right Angle Gearbox,Micro Size Spiral Bevel Gearbox,Small 90 Degree Gearbox Catalogue
JTA Light Weight Bevel Gearbox, Light Duty Bevel Gearbox, Smallest Aluminum 1 to 1 Ratio Miter Gearbox,Miniature Right Angle Gearbox,Micro Size Spiral Bevel Gearbox,Small 90 Degree Gearbox Catalogue
http://www.screw-jack.com
Contents
General information ----------------------------------------------------------------------------- 3 Specifications-------------------------------------------------------------------------------------- 4 Selection Guide 1. Gearbox Brand-------------------------------------------------------------------------------------- 5 2. Gearbox Series ------------------------------------------------------------------------------------- 5 3. Frame No. ------------------------------------------------------------------------------------------- 5 4. Gear Ratio ------------------------------------------------------------------------------------------- 5 5. Input & Output RPM--------------------------------------------------------------------------------- 5 6. Shaft Arrangements And Direction Of Shaft Rotating --------------------------------------------- 5-6 Dimensions
1. Model JTA10 ---------------------------------------------------------------------------------------- 7 2. Model JTA15 ---------------------------------------------------------------------------------------- 7 3. Model JTA20 ---------------------------------------------------------------------------------------- 8 4. Model JTA24 ---------------------------------------------------------------------------------------- 8
Operation Manual -------------------------------------------------------------------------------- 9-10 Frequently Asked Questions ----------------------------------------------------------------- 11 Company History --------------------------------------------------------------------------------- 12 Contact Us ------------------------------------------------------------------------------------------ 13
http://www.screw-jack.com
General Information
1. 4 models JTA10, JTA15, JTA20, JTA24 2. Corrosion resistant aluminum housing 3. High performance case hardened spiral bevel gear 4. Gear ratio 1:1 and 2:1 5. Small-sized, ultra light weight, high torque, low backlash 6. Universal mounting positions, can be easily mounted in any direction 7. Operating smoothly, low vibration, high efficiency, quiet running 8. Maximum strength and heat dissipation 9. Power from 0.01kw to 4.94kw, torque from 1.65Nm to 47.75Nm 10. Input both from the lateral shaft and cross shaft is available 11. Input shaft can rotate in both right-hand and left-hand directions 12. Maintenance free, long operating time 13. Lubricants prior to shipment
Materials: Housing: Die cast aluminum housing Spiral bevel gear: rugged alloy steel 20CrMnTiH, carburizing process, case hardened and lapped Drive shaft: hardened and tempered alloy steel, customized corrosion resistant stainless steel 304 Bearing: tapered roller bearing withstand heavy load Oil seal: double lip oil seal, prevent gear oil leak and dustproof
Applications: JTA series aluminum miter gearbox is application in farm equipment, paper, textile, food processing, printing machines, chemical mixers, packaging machinery, roller conveyors, aggregate and cement, agriculture, forestry, minerals and mining.
Lubricants: In the beginning to change the gear oil when the miter gearbox has been in service for two weeks or 100 ~ 200 hours. Routine oil change intervals will vary for each particular installation depending on the severity of the environment. Normal changes should occur 1000 ~ 2000 hours of operation.
http://www.screw-jack.com
Specifications
http://www.screw-jack.com
Selection Guide
JT 1 A 15 2 3 1:1 4 1450R 5 1450R 6 I-LR-O 7
1. Gearbox Brand
JT: Jacton brand miter gearbox
2. Gearbox Series
A: A series miter gearbox A: Aluminum housing
3. Frame No.
Frame No. Drive Shaft Diameter 10 10 mm 15 15 mm 20 20 mm 24 24 mm
Before selecting gearbox frame no., please check corresponding models specifications
4. Gear Ratio
Frame No. Gear Ratio 10 1:1 15 1:1 2:1 20 1:1 2:1 24 1:1 2:1
http://www.screw-jack.com
Example>>>>>> JT-A-15-2:1-1450R-725R-I-LR-O
1. Aluminum housing miter gearbox 2. Drive shaft diameter 15mm 3. Reduction gear ratio 2:1 4. Input 1450Rpm 5. Output 725Rrpm 6. 3 way drive shafts, input shaft clockwise, output shaft anti-clockwise
http://www.screw-jack.com
Dimensions
Model JTA10 Dimensions
http://www.screw-jack.com
http://www.screw-jack.com
Operation Manual
Please read this entire document prior to operating the miter gearbox. Miter gearbox failure or injury to operators may be caused by improper installation, operation or maintenance.
Installation
Miter gearboxs must be mounted on a rigid, structurally sound baseplate. Ensure that miter gearbox mounting pads rest evenly on the baseplate. The use of shims may be required to avoid housing distortion which could alter the gear mesh or cause premature bearing failure. The miter gearbox may be driven by direct coupling, flexible coupling, or V-belt drive. Couplers should require only a light force to install. The driveline must be accurately aligned within the equipment manufacturer's requirements to limit operating loads and minimize thrust loads on the miter gearbox shaft. V-belt drives must be mounted close to the housing to minimize excessive overhung loading which could result in early bearing or shaft failures. Sheaves must fit correctly. At installation, a tight forced fit could move the shaft from its normal position and cause internal damage. A loose fit could induce excessive vibration during operation and cause shaft damage or breakage.
Warning
When mounting the miter gearbox, the buyer is responsible to properly determine the quality or grade of fastener, thread engagement, load carrying capacity, and torque requirements.
Warning
The buyer is responsible to provide protective shields over all external rotating parts, couplers, or shaft extensions mounted on or with the miter gearbox. Protective clothing must be worn when installing or maintaining the miter gearbox and operating system. Initial operation should be carried out under no-load conditions. Before applying power to the miter gearbox installation, review the following: 1. Check tightness of mounting bolts. 2. Check for proper oil level in miter gearbox. 3. Be certain that tools, debris, etc., are clear from rotating parts. 4. Rotate shafts by hand. If they do not rotate freely, check for uneven mounting, coupling misalignment or excessive belt tension. If all tests are satisfactory, make connections to shafts, ensure that all safety devices are in place, and begin operation.
Lubrication
All miter gearboxes are factory tested prior to shipment. They include the correct amount of oil unless specified by the customer to be shipped dry. Shaft bearings are splash lubricated and partially submerged in oil when the miter gearbox is mounted horizontally. After installation, remove the dipstick and verify correct oil level. If no dipstick is provided, determine level by any appropriate method. In general, the oil level should be approximately half the depth of the miter gearbox (to the parting line) for horizontal mounting, or to the shaft centerlines, if mounted other than horizontally.
Caution
Prior to operation, make sure the miter gearbox contains the correct amount of oil. If under-filled or over-filled, damage to the miter gearbox or injury to personnel may result.
http://www.screw-jack.com
Approved Lubricants:
For miter gearboxs operating in an ambient temp of 20 Deg. C and +85 Deg. C Miter gearbox lubricant brand is VG220 (ISO viscosity class) When low speed less than 100Rpm, optional grease lubricant
Caution
Donot combine synthetic with non-synthetic oils in the miter gearbox.
Maintenance Warning
Disconnect power prior to any maintenance and do not bypass or inactivate any safety or protective device. Lock out and tag the power supply to prevent unexpected application of power. Routinely inspect mounting bolts, couplers,or other power transmitting devices to ensure all parts are firmly anchored.Keep shafts and vent plugs (when included) clean to prevent foreign particles from entering seals or housing. Inspect daily for any oil leaks and any unusual noises. Inspect weekly for end play in shafts. Inspect belt drive tension after the first ten hours of operation and periodically thereafter. Check the oil level every 24 hours of operation. In the beginning to change the oil when the miter gearbox has been in service for two weeks or 100 ~ 200 hours. Routine oil change intervals will vary for each particular installation depending on the severity of the environment. Normal changes should occur half ~ 1year or 1000 ~ 2000 hours of operation. The longest life at continuous service will be realized when the oil temperature does not exceed +85 deg. C. For oil substitutions, or for high input speeds, contact Jacton engineers.
Warning
Donot change or add oil while the miter gearbox is running. Damage to the miter gearbox or injury to personnel may result. The miter gearbox housing, oil, plugs, and associated components may reach high temperatures and cause severe burns. Use extreme care when servicing the miter gearbox.
Trouble Shooting
10
http://www.screw-jack.com
Can I Use Miter gearbox As Speed Increaser? All miter gearbox can be used as speed increaser, by inputting on the output side of the gearbox, however it is important to check whether the miter gearbox can handle the power and speed. When using as an increaser, the input speed does not exceed the specifications recommended maximum speed. Special gearbox is available where the pinion can be put on the through shaft so that two output shaft increase the speed.
Are Miter gearboxes Supplied Filled With Gear Oil? Yes, all miter gearboxes are filled gear oil prior to shipment, customers can install them and use them directly. Note: for low speed applications (100 rpm input speed and below) miter gearboxes may be recommended to have grease lubrication.
How Often Should I Change Gear Oil In The Miter gearbox? Check the gear oil level every 24 hours of operation. In the beginning to change the gear oil when the miter gearbox has been in service for two weeks or 100 ~ 200 hours. Routine oil change intervals will vary for each particular installation depending on the severity of the environment. Normal changes should occur half ~ 1year or 1000 ~ 2000 hours of operation. The longest life at continuous service will be realized when the oil temperature does not exceed +85 deg. C. For oil substitutions, or for high input speeds, contact Jacton engineers.
How Transmission Efficiency Of Miter gearbox? The miter gearbox transmission efficiency up to 98%
11
http://www.screw-jack.com
Company History
In 1997, Established Jacton Hardware Fabrication Plant, mainly processing kinds of hardware following customers requirements. Occupied 500 square meters. In 2000, Established domestic sales department, started to develop local market, mainly processing gear transmission parts such as worm and worm gear, acme threads screw, square threads screw and acme lead screw nut. Meanwhile, sales also sell straight bevel gear and spiral bevel gears for customers. In 2002, According to some regular customers of steel plants and machines manufacturers, which used Taiwan screw jacks and miter gearboxes, due to long delivery and high price, would affect the normal operations. Jacton Hardware Fabrication Plant started to processing JT acme screw jack and JT miter gearbox following above customers samples. In 2003, Established engineering department, research and development others models of JT acme screw jack and JT miter gearbox, and draw some factory production drawings and local sales' customers drawing with 2d autocad software. In 2005, According to local market demands, Jacton Hardware Fabrication Plant is committed to research and development JB/T8809-1998 standard JTW worm screw jack, JTM machine screw jack, JTB ball screw jack and JTP cubic body miter gearbox. In 2006, Because of local markets fiercely competitive. Established Hongkong office-Jacton International Limited with own US dollars and EURO account. Established international sales department, focused on overseas markets. Meanwhile, "JACTON" as company only brand. In 2008, According to intl sales market report, cubic body screw jacks and another type cubic body miter gearboxes are very popular in Europe and America markets. After managements meetings, we started to develop JTC cubic screw jack, JTS high speed bevel gear jack, JTV cubic body miter gearbox and JTA corrosion resistance aluminium body miter gearbox. In 2009, Jacton Hardware Fabrication Plant extension, occupied 5000 square meters. Company improves the processes and products through technology investment, brings in advanced technology, production and testing equipment. In 2010, Jacton Hardware Fabrication Plant Passed ISO9001:2008 quality management system, we are strictly implement the work flow of ISO9001:2008 certifications, which ensures oversea and local customers are satisfaction with our screw jacks and miter gearboxes and fast delivery time. In 2012, In order to facilitating management, according to management decisions, sales department and design department moved to Taibao business building. Meanwhile, Jacton Hardware Fabrication Plant changed to be Dongguan Jacton Electromechanical Co.,Ltd.
12
http://www.screw-jack.com
Contact Us
Jacton Electromechanical Co.,Ltd (Head Quarters) 1&2 Floors, Building F, Baisheng Industrial Areas, No.34, Yongjun Road, Datang,
Jacton Electromechanical Co.,Ltd (Sales Dept. & Design Dept.) 1118, Taibao Business Building, No.1 Langwei Rd, Xinan, Changan, Dongguan, Guangdong, China Phone: 86 769 81585852 Fax: 86 769 81620195
Dalingshan, Dongguan, Guangdong, China Phone: 86 769 81585810 Mobile: 86 189 25569548 Jacton International Limited (Hong Kong Branch) Office 17,9/F.,Tower A,New Plaza,No.14,Science Mandarin Road,
Contact Us General Enquiries: [email protected] [email protected] Online Skype: Online Skype: Website: jactonjack (Warren) jactongearbox (Abby) http://www.screw-jack.com
Museum
13
http://www.screw-jack.com