SAMSON

Surface Treatment

Expertise in Surface Treatment

Surface preparation Coating systems Corrosion protection

Expertise in Surface Treatment Surface treatment of SAMSON products

Contents
1 Scope................................................................................................................................................................3 2 Validity of this manual........................................................................................................................................3 3 Intended use of this manual................................................................................................................................3 4 General.............................................................................................................................................................4 4.1 Terms and standards...................................................................................................................................4 4.2 Durability and corrosion protection categories...............................................................................................5 5 Surface treatment at SAMSON...........................................................................................................................6 5.1 Surface preparation....................................................................................................................................6 6 Coating systems.................................................................................................................................................7 6.1 General description of the painting process...................................................................................................7 6.2 Paint specifications......................................................................................................................................9 6.3 Customized solutions................................................................................................................................. 13 7 Quality assurance............................................................................................................................................14 7.1 Film thickness measurement according to ISO 2178 = Film thickness measurement - Magnetic method and ISO 2360 = Film thickness measurement - Non-destructive eddy current method............................................. 14 7.2 Cross-cut test according to ISO2409 or ASTMD3359.................................................................................. 16 7.3 Pull-off test according to ISO4624 or ASTMD4541..................................................................................... 17 8 Environmental protection..................................................................................................................................18 9 FAQs (Frequently Asked Questions)...................................................................................................................19

Expertise in Surface Treatment Surface treatment of SAMSON products

1 Scope
Surface treatment, especially to provide corrosion protection, is becoming increasingly important. This manual provides information on surface treatment at SAMSON and assists users in selecting a suitable coating system.

2 Validity of this manual

This manual applies to control valves and instruments manufactured by SAMSON AG. Further information on products can be found in the corresponding data sheets.

3 Intended use of this manual

This manual is intended to assist planners and operators in selecting a suitable protective coating system for a control valve or instrument. Valves and instruments are to be started up and maintained by qualified personnel only. For further details, refer to the mounting and operating instructions, coating specifications and repair procedures.

Expertise in Surface Treatment Surface treatment of SAMSON products

4 General
4.1 Terms and standards
Control valves are used in various applications and locations. The ambient conditions at the site of installation vary significantly and place different demands on the surface finish. Corrosion can arise and damage valve components. SAMSON has the right protective coating system to suit all types of environmental conditions (e.g. abrasive wear or corrosive environment). What is corrosion? The term corrosion is generally understood to mean a process that causes the deterioration of materials and often even the failure of a product. Corrosion is defined as the reaction of a material with its environment, which effects measurable change in the material and can lead to impairment of the function of components or of an entire system. The reaction can be induced by environmental effects as well as by mechanical or dynamic stress.
Combined effects Mechanical Sliding abrasion Rolling wear Rolling/sliding wear Fretting wear Cavitation wear Erosive wear Solid particle erosion High velocity erosion Wear Fretting corrosion Cavitation corrosion Erosion corrosion Chemical

Wear DIN 50320

Corrosion ISO 8044

There are different kinds of corrosion, such as crevice corrosion, pitting corrosion, shallow pitting or surface corrosion, as well as various causes of corrosion. Corrosion damage occurs when a components function is impaired or it fails completely. Relevant standards
Standard ISO 12944-1 to -8 DIN 55633 ISO 8501-1 ISO 2178 ISO 2409 and ASTM D3359 ISO 4624 and ASTM D4541 DIN 50018 ISO 6988 ISO 9227 and ASTM B117 Designation Paints and varnishes Corrosion protection of steel structures by protective paint systems Paints and varnishes - Corrosion protection of steel structures by powder coating systems Preparation of steel substrates before application of paints and related products Non-magnetic coatings on magnetic substrates Measurement of coating thickness Magnetic method Paints - Cross-cut test Paints and varnishes Pull-off test for adhesion Testing in a saturated atmosphere in the presence of sulfur dioxide Metallic and other non-organic coatings Sulfur dioxide test with general condensation of moisture Corrosion tests in artificial atmospheres Salt spray tests

Expertise in Surface Treatment Surface treatment of SAMSON products

4.2 Durability and corrosion protection categories

ISO 12944-5 determines the various coating durability ranges and ISO 12944-2 classifies the corrosivity categories for protective coating systems. The durability does not constitute a warranty period. It is a technical term to help users establish a maintenance scheme. The durability describes the time period within which a painted component is protected against corrosion.

ISO 12944-5 Durability Low (L) Medium (M) High (H)

Time span 2 to 5 years 5 to 15 years More than 15 years

The corrosivity categories provide a uniform classification to clearly assign corrosion stress and environmental conditions. This helps in selecting a suitable protective coating system for each application.
ISO 12944-2 Corrosivity category C1 (very low) C2 (low) C3 (medium) C4 (high) C5-I (very high, industrial) C5-M (very high, marine) Im1 Im2 Im3 Typical ambient conditions Heated buildings with neutral atmospheres Atmospheres with low level of pollution, unheated buildings where condensation may occur Urban and industrial atmospheres, medium level of pollution (sulfur dioxide), coastal areas with low salinity, production rooms with high humidity and some air pollution Industrial areas and coastal areas with moderate salinity, chemical plants, swimming pools etc. Industrial areas with high humidity, aggressive atmosphere, buildings or areas with almost permanent condensation and with high pollution Coastal and offshore areas with high salinity, buildings or areas with almost permanent condensation and with high pollution Fresh water: river installations, hydroelectric power plants Sea or brackish water: harbor areas with structures like sluice gates, locks, jetties; offshore structures Soil: buried tanks, steel pile walls, steel pipes

Expertise in Surface Treatment Surface treatment of SAMSON products

5 Surface treatment at SAMSON

Corrosion can cause great economic loss. Damage to the environment cannot be ruled out either. To counteract corrosion damage caused by corrosion, the surface treatment at SAMSON is performed according to paint suppliers specifications under controlled process and ambient conditions (e.g. constant temperature and air humidity monitoring) in a heated building. Ongoing testing during the coating procedures additionally ensure that surface treatment remains at a constantly high quality.

5.1 Surface preparation

Optimal surface preparation is necessary to achieve durable, long-lasting corrosion protection by subjecting parts to chemical or electrochemical surface treatment.
Surface preparation

Degreasing

Rinsing

Etching

Zinc/chromate

Paint system

Rinsing

Zinc/phosphate

Paint system

Passivation

Paint system

Expertise in Surface Treatment Surface treatment of SAMSON products

6 Coating systems
6.1 General description of the painting process1
Powder coating Powder coating involves applying the paint or protective coating as dry powder. The powder is electrostatically charged, sprayed onto the component and cured in an oven. Advantages:
Free from volatile organic compounds No solvent emissions Less toxic waste Minimized waste and high powder yield (up to 98%) thanks to recovery Excellent coating quality Excellent adhesion to the substrate High film thickness can be achieved High level of automation possible Suitable for ambient conditions classified in C1 to C5-M

1 The individual film thicknesses can be customized on request Specifications subject to change without notice

Expertise in Surface Treatment Surface treatment of SAMSON products

Wet painting Air gun spraying Wet paint coatings are liquid mixtures of substances that form a firmly adheive coat after they have dried on the surface of the component. Depending on the intended application, the paint contains dyes, pigments, fillers, softeners, resins and binders. In addition to giving the component the desired appearance, the paint coating protects against damage and corrosion. Advantages:
Well-suited for one-off or small series production Multilayer coatings with variable layer structures possible Easy change of paint and component Coating of heat-sensitive components possible Customizable color

Expertise in Surface Treatment Surface treatment of SAMSON products

6.2 Paint specifications

1. Powder coating for corrosivity categories C2 and C3 according to ISO12944-5 (standard surface treament)
Coating system no. 1 Typical environment Industry, chemical plants, coastal areas Surface preparation Sa 2 according to ISO 8501-1 System description First layer Film thickness Method of application Min. 70 m Powder coating (epoxy-polyester) Min. 70 m RAL 1019 (gray beige)

Total film thickness RAL code or standard color

2. Wet paint coating system for corrosivity categories C2 and C3 according to ISO12944-5 (standard surface treament)
Coating system no. 2 Typical environment Industry, chemical plants, coastal areas Surface preparation Sa 2 according to ISO 8501-1 System description First layer Second layer Film thickness Method of application Film thickness Method of application Min. 50 m Spray painting (epoxy) Min. 50 m Spray painting (polyurethane) Min. 100 m RAL 1019 (gray beige)

Total film thickness RAL code or standard color

Expertise in Surface Treatment Surface treatment of SAMSON products

3. Powder coating system with final sealant for corrosivity categories C4, C5-I and C5-M according to ISO12944-5
Coating system no. 3 Typical environment Industrial areas with high humidity and aggressive atmosphere, river deltas, maritime and coastal areas with a high salinity C5-M, very high, marine (long) Surface preparation Sa 2 according to ISO 8501-1 System description First layer Second layer Third layer Film thickness Method of application Film thickness Method of application Film thickness Method of application Min. 100 m Powder coating (epoxy-polyester) Min. 100 m Powder coating (epoxy-polyester) Min. 50 m Spray painting (polyurethane) Min. 250 m RAL 1019 (gray beige)

Total film thickness RAL code or standard color

4. Wet paint coating system for corrosivity categories C4, C5-I and C5-M according to ISO12944-5
Coating system no. 4 Typical environment Industrial areas with high humidity and aggressive atmosphere, river deltas, maritime and coastal areas with a high salinity C5-M, very high, marine (long) Surface preparation Sa 2 according to ISO 8501-1 System description First layer Second layer Third layer Film thickness Method of application Film thickness Method of application Film thickness Method of application Min. 75 m Spray painting (two-compenent zinc phosphate primer) Min. 100 m Spray painting (two-component epoxy micaceous iron oxide coating) Min. 55 m Spray painting (polyurethane) Min. 230 m RAL 1019 (gray beige)

Total film thickness RAL code or standard color

10

Expertise in Surface Treatment Surface treatment of SAMSON products

5. Wet paint coating system for high-temperature applications

Coating system no. 5 Typical environment Industry, chemical plants, coastal areas Surface preparation Sa 2 according to ISO 8501-1 System description First layer Second layer Third layer Film thickness Method of application Film thickness Method of application Film thickness Method of application Min. 75 m Spray painting (zinc-rich ethyl silicate primer) Min. 25 m, max. 35 m Spray painting (high-temperature silicone coating) Min. 25 m, max. 35 m Spray painting (high-temperature silicone coating) Min. 125 m, max. 145 m RAL 9006 (white aluminum)

Total film thickness RAL code or standard color

6. Wet paint coating system for high-temperature applications

Coating system no. 6 Typical environment Industry, chemical plants, coastal areas Surface preparation Sa 2 according to ISO 8501-1 System description First layer Second layer Film thickness Method of application Film thickness Method of application Min. 25 m, max. 35 m Spray painting (high-temperature silicone coating) Min. 25 m, max. 35 m Spray painting (high-temperature silicone coating) Min. 50 m, max. 70 m RAL 9006 (white aluminum)

Total film thickness RAL code or standard color

11

Expertise in Surface Treatment Surface treatment of SAMSON products

7. Wet paint coating system for stainless steel for corrosivity categories C5-I and C5-M according to ISO12944-5
Coating system no. 7 Typical environment Industrial areas with high humidity and aggressive atmosphere, river deltas, maritime and coastal areas with a high salinity C5-M, very high, marine (long) Surface preparation Sa 2 according to ISO 8501-1 System description First layer Second layer Third layer Film thickness Method of application Film thickness Method of application Film thickness Method of application Min. 80 m Spray painting (epoxy) Min. 80 m Spray painting (two-component epoxy micaceous iron oxide coating) Min. 80 m Spray painting (polyurethane) Min. 240 m RAL 1019 (gray beige)

Total film thickness RAL code or standard color

8. Coating system for stainless steel for corrosivity categories C5-I and C5-M according to ISO12944-5
Coating system no. 8 Typical environment Industry, chemical plants, coastal areas Surface treatment Sa 2 according to ISO 8501-1 System description First layer Second layer Film thickness Method of application Film thickness Method of application Min. 100 m Spray painting (epoxy phenolic coating) Min. 100 m Spray painting (epoxy phenolic coating) Min. 200 m RAL 1019 (gray beige)

Total film thickness RAL code or standard color

12

Expertise in Surface Treatment Surface treatment of SAMSON products

6.3 Customized solutions

Contact SAMSON if you require a protective coating system not included in this brochure or simply want a different color. Color RAL 1019 is the standard color for SAMSON products. Other colors are possible on request to meet all international standards. Specify the exact color code for customized solutions.

Special requirements for protective coating systems The following customized solutions are available:
Coating systems according to NORSOK M-501 Customized coatings for applications at high or low temperatures Coatings according to customer specifications (after thorough examination) The individual film thicknesses of all coating systems can be customized on request (within the manufacturers

specifications)

13

Expertise in Surface Treatment Surface treatment of SAMSON products

7 Quality assurance
Ongoing tests of coating systems are performed to ensure a constantly high quality:
Standardized film thickness measurement in accordance with

ISO 2178 = Film thickness measurement - Magnetic method and ISO 2360 = Film thickness measurement - Non-destructive eddy current method

Cross-cut test according to ISO2409 and ASTMD3359 Pull-off test according to ISO4624 and ASTMD4541

Test results can be supplied in a test protocol on request. Further tests, such as corrosion and adhesion tests, are performed either by our paint suppliers or external inspectors. These results can be made available, if required.

7.1 Film thickness measurement according to ISO 2178 = Film thickness measurement - Magnetic method and ISO 2360 = Film thickness measurement - Non-destructive eddy current method
The film thickness is measured according to ISO12944 or ISO19840 using the non-destructive eddy current method. To provide comparable test results, the film thickness is measured at critical defined measuring points.

14

Expertise in Surface Treatment Surface treatment of SAMSON products

Measuring point 1

Measuring point 2

Measuring point 3

Measuring point 4

Measuring point 1

Measuring point 3 Opposite measuring point 1

Measuring point 2

Measuring point 4 Opposite measuring point2

Measuring point 1

Measuring point 2 Opposite measuring point1

Measuring point 3

Measuring point 4 Opposite measuring point3

Measuring point 1 Measuring point 3 Measuring point 5 Measuring point 7

Measuring point 2 Opposite measuring point1 Measuring point 4 Opposite measuring point3 Measuring point 6 Opposite measuring point 5 Measuring point 8 Opposite measuring point 7

15

Expertise in Surface Treatment Surface treatment of SAMSON products

7.2 Cross-cut test according to ISO2409 or ASTMD3359

The destructive cross-cut test is performed using a test plate representative of the substrate treated in the same process in accordance with ISO2409 or ASTMD3359. All test data are saved in a database to continuously document the process.
Description of cross-cut test To assess the resistance of a paint coating to separation from the substrate (adhesion). The procedure is performed on test plates (100 x 100mm) according to ISO2409. Permissible cross-cut classes: 0 and 1 Classification 0 1 Description The edges of the cuts are completely smooth; none of the squares of the lattice is detached. Detachment of small flakes of the coating at the intersections of the cuts. A cross-cut area not significantly greater than 5% is affected. The coating has flaked along the edges and/or at the intersections of the cuts. A cross-cut area significantly greater than 5 %, but not significantly greater than 15 %, is affected. Surface appearance in the area of the cross cut where the coating has flaked (example for six parallel cuts)

16

Expertise in Surface Treatment Surface treatment of SAMSON products

7.3 Pull-off test according to ISO4624 or ASTMD4541

The destructive pull-off test is used to determine the adhesion performance of the paint product to the substrate. Similar to the cross-cut test, it is performed using a test plate representative of the substrate treated in the same process in accordance with ISO4624 or ASTMD4541.

17

Expertise in Surface Treatment Surface treatment of SAMSON products

8 Environmental protection
Environmentally safe powder coating
Free from volatile organic compounds (e.g. solvents) Up to 98% yield is achieved by recovering overspray

Voluntary self-declaration: chromium(VI)-free passivation Waste water cleaning

Precipitation of heavy metals and other suspended matter pH neutralization Professional waste disposal

18

Expertise in Surface Treatment Surface treatment of SAMSON products

9 FAQs (Frequently Asked Questions)

1. What needs to be observed when selecting a high-temperature paint coating? For high-temperature or low-temperature applications, all the coats of the paint system must be suitable for the selected temperature range. 2. Why are zinc primers not used? Components already have a sealed protective zinc coating after passivation by applying the zinc phosphate coating. For better adhesion of subsequent paint layers, a primer is used, making a zinc primer superfluous. 3. Can the film thicknesses of the paint coatings be varied? Depending on the requirements, after consulting SAMSON, individual coats can be thicker within the range specified by the paint manufacturer. 4. Which paint coating is used for use under tropical conditions? Electrical instruments for use under tropical conditions are painted according to coating system no. 3 or have a polyurethane top coat. 5. What is the difference between polyurethane and DD coatings? DD coatings are composed of polyols (Desmophen) as the base paint and polyisocyanates (Desmodur) as the hardener. The DD coating is a two-component polyurethane-based coating with the base paint containing the pigments.

19

Local customer assistance across the world

Specifications subject to change without notice.

SAMSON AG MESS- UND REGELTECHNIK Weismllerstrae 3 60314 Frankfurt am Main Germany Phone: +49 69 4009-0 Fax: +49 69 4009-1507 E-mail: [email protected] Internet: www.samson.de SAMSON GROUP www.samsongroup.net

2012-09 HD WA 268 EN