04main Measure Insp Sensors

LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
MEASUREMENT & INSPECTION

Light Gauging LT3 LT7 LH LG page 295
SENSORS
Ultrasonic QT50U S18U QS18U T30U/T30UX M25U T18U Q45U Q45UR Measuring Arrays
page 308
page 340
EZ-ARRAY High-Resolution MIN-ARRAY MINI-ARRAY
Radar QT50R
page 354
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
292
More information online at bannerengineering.com
Light Gauging Sensors

Light gauging sensors utilize either Time of Flight or triangulation technology to detect the presence and position of targets. Time of Flight: Measurement of the amount of time that emitted light takes to travel to the target and return to the sensor. This technology is used in long-range sensing applications. Triangulation: An emitter transmits visible light through a lens, towards a target. The beam bounces off the target, returning some light to the sensors Position Sensitive Device (PSD) receiver element. The targets distance from the receiver determines the angle at which the light travels to the receiver element. This angle, in turn, determines where the received light will fall along the PSD receiver element. The position of the light on the PSD receiver element is processed through analog and/or digital electronics to calculate the appropriate output value.
PSD Receiver Element
Color Effects
The color of the object being measured can affect the resolution and accuracy of the readings. White, red, yellow and orange targets will reflect more light than green, blue or black targets. The resolution for dark targets may be up to four times less than for white targets.
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors Measurement & Inspection Sensors Vision Wireless Lighting & Indicators Safety Light Screens Safety Laser Scanners Fiber Optic Safety Systems Safety Controllers & Modules
The graph below shows the relative amount of received light that is reflected from various target colors, using visible red light. The resolution is roughly affected according to the square of the received light. For example, reducing the amount of light by a factor of nine will degrade the resolution by a factor of three.
Lenses Near Limit Far Limit
Safety Two-Hand Control Modules Safety Interlock Switches Emergency Stop & Stop Control
Signal Conditioning Circuitry
Object Movement Microprocessor
Output Circuitry Emitter Circuitry E Laser Emitter Programmed Sensing Window
LIGHT GAUGING ULTRASONIC MEASURING ARRAYS RADAR
Triangulation Technology
Surface Reflectivity and Texture

Triangulation sensors depend on the diffuse reflections of light from the target. A diffuse reflection is one in which the light tends to scatter equally in all directions from the target. If the target surface is mirror-like, then light will tend to reflect in only one direction (If this target is not perpendicular to the sensor, the light will be reflected away from the sensor). Triangulation sensors also require a non-porous, opaque surface for accurate operation. Measurement errors will result from semi-transparent targets such as clear plastic, or from porous materials such as foam.
Metal Surfaces
Signal
PSD Receiver Element
Conditioning consistent reflectivity across Bare metal surfaces do not exhibit their Farsurfaces. As a Near Circuitry Limit Limit Lenses result, the repeatability from one point on a metal surface to another, even at the same Object Movement Microprocessor distance from the sensor, will degrade. This effect varies from metal to metal and is dependent upon surface finish. Output Circuitry Emitter Circuitry
E Laser Emitter
Programmed Sensing Window
Best
Worst
Typical
X
More light is reflected in the y-direction than the x-direction
Diffuse targets (e.g., matte finish white ceramic) reflect light consistently in all directions
Specular targets (e.g., a mirror) reflect light in only one direction
Mixed targets (most objects) display traits of both diffuse and specular targets
Total Expected Measurement Error

Keep in mind that the overall expected accuracy of an analog sensor is the combination of several performance parameters, not simply the sensors resolution. Linearity and temperature effect can also affect accuracy.
293
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
Ultrasonic Sensors
Ultrasonic sensors emit a pulse of energy which travels at the speed of sound. A portion of this energy is reflected off of a target and travels back to the sensor. The sensor measures the total time required for the energy to reach the target and return to the sensor and calculates the distance from the sensor to the target.
Target Angle
A flat target that is perpendicular to the beam axis will reflect the most sound energy back to the sensor. As the target angle increases, the amount of energy received by the sensor decreases. For most ultrasonic sensors, the target angle should be 10 or less.
Target Angle
SENSORS
Temperature Effect
The speed of sound depends on chemical composition, pressure and temperature of the gas in which it is traveling. In most ultrasonic applications, the composition and pressure of the gas are relatively fixed, while the temperature is not. The speed of sound increases roughly 1% per 10 F (6 C) temperature increase.
Sensor
Air Currents
Cold Environment
Air currents due to wind, fans, pneumatic equipment or other sources can deflect or disturb the path of the ultrasonic energy, so a sensor may fail to recognize the correct location of the target.
Warm Environment
Measuring Light Screens

Banner light screens have a vertical array of photoelectric emitters and receivers: The emitters in one housing, the receivers in another. An object placed between the emitter and receiver will block the emitted light from reaching the corresponding receivers.
Minimum Object Detection

The minimum object detection size is a function of the lens diameter for an individual channel and the spacing between channels. The minimum object detection size is defined as the smallest diameter rod that can be detected reliably.
Maximum Part Speed

Emitter Receiver
Synchronous Scanning
Identifies which of the beams is blocked, by enabling one emitter channel to pulse light while simultaneously directing its corresponding receiver to look for a signal. The system records which beam channels are blocked and which are clear, and then outputs a signal, either analog or discrete.
The maximum speed of a passing part is a function of the part size, the lens diameter and the maximum response time of the system.
Measuring Modes Sensor Response Time

The time required for an array system to see an object varies depending on which channel is blocked, when the object blocks a particular channel and when that particular channel is scanned. The result is that the minimum response time is equal to 1 ms; the maximum response time is equal to twice the scan time. The scan time, in turn, varies according to array length and scanning mode, and is specified in the product literature. Banners measuring light screens can be configured, with a simple Windows setup program, for several measuring modes for both analog and discrete outputs. For example, the output can be based on the: First beam blocked Last beam blocked Total number of beams blocked First beam made Last beam made Total number of beams made Center beam of several blocked beams Number of transitions from blocked to made Highest number of contiguous beams blocked
294
L-GAGE LIGHT GAUGING SENSORS

LT3 LT7 LH LG
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors Measurement & Inspection Sensors Vision Wireless Lighting & Indicators Safety Light Screens Safety Laser Scanners Fiber Optic Safety Systems Safety Controllers & Modules Safety Two-Hand Control Modules Safety Interlock Switches Emergency Stop & Stop Control
LIGHT GAUGING ULTRASONIC MEASURING ARRAYS RADAR
LT3
page 296
LT7
page 300 LH
page 303 LG
page 305
Exceptionally accurate advanced time-of-flight sensing technology provides precise measurements over long ranges. Retroreflective mode sensor has 50 m range. Ranges with diffuse-mode sensor are 5 m for white targets and 3 m for gray targets. Sensors offer either analog and discrete, or dual-discrete output with independent window limits.
Extremely long-range sensor uses a Class 1 laser beam for accuracy over long distances. Retroreflective-mode sensor has 250 m range. Ranges with diffuse-mode sensor are up to 10 m for white, 7 m for gray and 3 m for black targets. Models are available with discrete output only or with discrete and analog output. RS-422 or SSI compatible serial connections are provided.
High-precision laser displacement sensor provides reliable measurement results on real-world targets, such as machined metal, wood, ceramic and paper. Non-contact sensor provides precise measurement on moving processes, hot parts, machined parts, and soft or sticky parts. Ranges are up to 200 mm, depending on model. Two sensors self-synchronize for easy thickness measurements and calculations.
One-piece laser gauging system requires no separate controller. Ultra narrow beam delivers precise distance, height and thickness measurement and gauging. Two sensing ranges are available: 45 to 60 mm and 75 to 125 mm.
295
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
L-GAGE LT3
SENSORS
ACCESSORIES
Laser Distance-Gauging Sensors

Uses advanced time-of-flight technology for precise, long-distance gauging at the speed of light Available in diffuse-mode models with ranges to 5 m and retroreflective models with a 50 m range Offered in dual-discrete or analog/discrete models Features push-button TEACH-mode programming for custom sensing windows Offers remote programming for added security and convenience Includes push-button programming for three output response speeds Simplifies alignment with a bright, visible laser spot Emits one million pulses per second Reliably detects angled targets Uses rugged construction to withstand demanding sensing environmentsrated IEC IP67; NEMA 6
page 299
CLASS 1 LASER PRODUCT
LASER LIGHT
LT3 Sensing Ranges

LASER DIFFUSE
RADIANT POWER 0.15mW 10ns PULSE, 1MHz 650 - 670 nm Complies with IEC 60825-1:2001 and 21 CFR 1040.10 & 1040.11 except for deviations pursuant to Laser Notice No. 50, dated July 26, 2001
Diffuse models with gray targets: 0.3 - 3 m Diffuse models with white targets: 0.3 - 5 m
Class 1 Label
Laser light emitted from this aperture
RETRO LASER
LASER LIGHT
DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT
Retroreflective models with retroreflector: 0.5 - 50 m Meters
RADIANT POWER 0.5mW 10ns PULSE, 1MHz 650 - 670 nm COMPLIES TO 21 CFR PART 1040.10 AND EN60825-1:1994
Avoid exposure- laser light emitted from this aperture
5 . . .
50
Class 2 Label
87.0 mm
48.8 mm
E YL
PIGTAIL P
UR
EURO
68.5 mm
QPMA
CA LL FACTORY
online
AUTOCAD, STEP, IGES & PDF
-S
A BL
75.6 mm 35.3 mm
296
L-GAGE LT3, 12-24V dc

Sensing Mode/LED Laser Class Sensing Distance Connection
2m 8-pin Euro QD Class 2
DIFFUSE LASER
Visible Red Laser
Analog Output
None
Models NPN
Models PNP
LT3BD (Dual NPN or PNP selectable) LT3BDQ (Dual NPN or PNP selectable) LT3NU LT3NUQ 4 to 20 mA LT3NI LT3NIQ None LT3PU LT3PUQ LT3PI LT3PIQ
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors Measurement & Inspection Sensors Vision Wireless
0.3 to 5 m for 90% reflectivity white card (see Performance Curve RRC-1 on page 299 for more information)
2m 8-pin Euro QD 2m 8-pin Euro QD 2m 8-pin Euro QD
0 to 10V dc
Lighting & Indicators Safety Light Screens Safety Laser Scanners Fiber Optic Safety Systems Safety Controllers & Modules Safety Two-Hand Control Modules Safety Interlock Switches Emergency Stop & Stop Control
ACCESSORIES
LT3BDLV (Dual NPN or PNP selectable) LT3BDLVQ (Dual NPN or PNP selectable) LT3NULV LT3NULVQ LT3PULV LT3PULVQ LT3PILV LT3PILVQ
Class 1
LASER RETRO
0.5 to 50 m (see Performance Curve RRC-2 on page 299 for more information)
2m 8-pin Euro QD 2m 8-pin Euro QD
0 to 10V dc
4 to 20 mA
LT3NILV LT3NILVQ
Connection options: A model with a QD requires a mating cordset (see page 29 9). For 9 m cable, add suffix W/30 to the 2 m model number (example, LT3BD W/30).
page 299
Retroreflective range is specified using a BRT-TVHG-8X10P high-grade target. Actual sensing range may differ, depending on the efficiency and reflective area of the retroreflector used. See Accessories for more information. LIGHT GAUGING LT3 LT7 LH LG ULTRASONIC MEASURING ARRAYS RADAR
L-GAGE LT3 Specifications

Sensing Beam Typical beam diameter: 6 mm @ 3 m Typical laser lifetime: 75,000 hours Diffuse: 658 nm visible red IEC and CDRH Class 2 laser; 0.5 mW max. radiant output power Retroreflective: 658 nm visible red IEC and CDRH Class 1 laser, 0.15 mW max. radiant output power Diffuse: 90% white card: 0.3 to 5 m 18% gray card: 0.3 to 3 m 6% black card: 0.3 to 2 m Retroreflective: 0.5 to 50 m (using supplied target)
Sensing Range
Supply Voltage and Current Supply Protection Circuitry Delay at Power-up Output Rating
12 to 24V dc (10% max. ripple); 108 mA max. @ 24V dc or [2600/V dc] mA Protected against reverse polarity and transient voltages 1 second; outputs do not conduct during this time Discrete (switched) output: 100 mA max. OFF-state leakage current: less than 5 A Output saturation NPN: less than 200 mV @ 10 mA; less than 600 mV @ 100 mA Output saturation PNP: less than 1.2V at 10 mA; less than 1.6V at 100 mA Analog voltage output: 2.5 k min. load impedance (voltage sourcing) Analog current output: 1 k max. @ 24V; max. load resistance = [Vcc-4.5/0.02 ] (current sourcing) Discrete (switched): Solid-state switch; NPN (current sinking) or PNP (current sourcing), depending on model. Dual-discrete models feature selectable NPN or PNP, depending on wiring hookup. Analog output: 0 to 10V dc or 4 to 20 mA Protected against short circuit conditions
Output Configuration
Output Protection
More on next page
297
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR

Output Response Time
(contd)
SENSORS
Discrete output Fast: 1 millisecond ON/OFF Medium: 10 milliseconds ON/OFF Slow: 100 milliseconds ON/OFF Diffuse Analog Voltage output (-3 dB) Fast: 450 Hz (1 millisecond average/1 millisecond update rate) Medium: 45 Hz (10 milliseconds average/2 milliseconds update rate) Slow: 4.5 Hz (100 milliseconds average/4 milliseconds update rate) Retroreflective Analog Voltage output (-3 dB) Fast: 114 Hz (6 milliseconds average/ 1 millisecond update rate) Medium: 10 Hz (48 milliseconds average/ 1 millisecond update rate) Slow: 2.5 Hz (192 milliseconds average/ 1 millisecond update rate) See charts RRC-1 and RRC-2 on page 299. Diffuse: 90% white to 18% gray: less than 10 mm; 90% white to 6% black: less than 20 mm. See chart CSC-1 on page 299. Retroreflective: 60 mm from 0.5 to 50 m (0.12% of full scale) (Specified @ 24V dc, 22 C using supplied BRT-TVHG-8X10P retroreflector) Diffuse: 30 mm from 0.3 to 1.5 m; 20 mm from 1.5 to 5 m (Specified @ 24V dc, 22 C using a 90% reflectance white card)
Resolution/Repeatability Color Sensitivity (typical) Analog Linearity
Discrete Output Hysteresis
Diffuse Fast: 10 mm Medium: 5 mm Slow: 3 mm Diffuse: less than 2 mm/ C Diffuse: 20 mm 18 k min. (65 k at 5V dc)
Retroreflective Fast: 20 mm Medium: 10 mm Slow: 6 mm Retroreflective: less than 3 mm/ C Retroreflective: 40 mm
Temperature Effect Minimum Window Size Remote TEACH Input Remote TEACH Adjustments
To teach: Connect yellow wire to +5 to 24V dc To disable: Connect yellow wire to 0 to +2V dc (or open connection) Response speed: Push button toggles between fast, medium and slow (see Output Response Time) Window limits (analog or discrete): TEACH-mode programming of near and far window limits. Limits may also be taught remotely using TEACH input. Analog output slope: The first limit taught is assigned to minimum output current or voltage (4 mA or 0V dc) Connect red wire to +5 to 24V dc to enable laser beam; connect to 0 to +1.8V dc (or open connection) to disable. See data sheet for delay time on enable. Green Power ON LED: Indicates when power is ON, overloaded output and laser status Yellow Output LED: Indicates when discrete load output is conducting Red Signal LED: Indicates target is within sensing range and the condition of the received light signal Yellow Speed LED: Indicates the response speed setting Red/Yellow TEACH LEDs: In programming mode; indicate active output(s) Housing: ABS/polycarbonate blend Window: Acrylic Quick-disconnect: ABS/polycarbonate blend IP67; NEMA 6 2 m or 9 m shielded 7-conductor (with drain) PVC-jacketed attached cable, or 8-pin Euro-style quick-disconnect. QD cordsets are ordered separately. See page 299. Temperature: 0 to +50 C Relative humidity: 90% at 50 C (non-condensing)
Laser Control Indicators
Construction
Environmental Rating Connections Operating Conditions Application Notes
For best accuracy, allow 30-minute warm-up before programming or operating Retroreflective performance specifications are based on use with supplied BRT-TVHG-8X10P high-grade target. Results may vary with other retroreflective target materials.
Certifications Hookup Diagrams Discrete/Analog Models: NPN: MI01 (p. 758) Dual-Discrete Models: NPN: MI03 (p. 758) PNP: MI02 (p. 758) PNP: MI04 (p. 758)
298
Cordsets
Euro QD (With Shield)
See page 689 Length
2m 5m 9m
Brackets
LT3
REFLECTORS
REFLECTORS
Threaded 8-Pin Straight

MQDC-806 MQDC-815 MQDC-830 Additional cordset information available. See page 679. pg. 650 SMBAMSLT3IP pg. 657 SMBLT31 pg. 657 SMBLT32 pg. 658 SMBLT3IP
PAGE 710
Additional brackets and information available. See page 620.
Repeatability/Resolution Curves
= Visible Red Laser
LT3
5 4 3 2 1 Slow 0 0 1 2 3 4 5 Medium Resolution/Repeatability vs. Distance 20 18 Fast Repeatability (mm) 16 14 12 10 8 6 4 2 0 0 10
LT3
Resolution/Repeatability vs. Distance
Fast
LIGHT GAUGING LT3 LT7 LH
Medium Slow
Resolution (mm)
LG ULTRASONIC MEASURING ARRAYS RADAR

50
6% Black 18% Gray 90% White
Distance (m)
20 30 Distance (m)
40
RRC-1
RRC-2
Range: 5 m
Mode: Diffuse
LED:
Range: 50 m
Mode: Retroreflective
LED:
Color Sensitivity Curves

= Visible Red Laser
LT3
20 Color Sensitivity (mm) 10 0 -10 -20 -30 -40 0 1 2 3 Target Position (m) 4 5
90% White to 18% Gray 90% White to 6% Black
CSC-1
Range: 5 m
Mode: Diffuse
LED:
299
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
L-GAGE LT7
SENSORS
ACCESSORIES
Highly Accurate Time-of-Flight Laser Gauging Sensors

Available in extremely long-range retroreflective models with ranges to 250 m or in diffuse models with ranges to 10 m Provides two alarm outputs with ongoing LCD display for easy troubleshooting Offered in dual-discrete or analog/discrete models Features TEACH-mode programming using integrated push buttons or a serial interface Continually displays sensing distance in millimeters or hundredths of an inch Delivers excellent 10 mm linearity Offers choice of RS-422 or SSI-compatible serial connection Uses visible Class 2 alignment laser for accurate alignment Provides quick warmup to minimize drift
page 302
LT7 Sensing Ranges

Diffuse models with gray targets: 0.5 - 7 m Diffuse models with white targets: 0.5 - 10 m
Operating Mode Laser Class 1 Setup Mode Laser Class 2 Do not stare into beam
LASER DIFFUSE
RETRO LASER
Retroreflective models with specified reflector: 0.5 - 250 m 250 . . . 10 Meters
95.0 mm
81.5 mm
93.0 mm
online
42.0 mm
42.0 mm
300
L-GAGE LT7, 18-30V dc

Sensing Mode/LED Laser Class Sensing Distance* Connection Discrete Output Analog Output
12-pin M16 QD 0.5 to 10 m
DIFFUSE LASER Connection options: A model with a QD requires a mating cordset (see page 302). * Diffuse-mode range specified using a 90% reflectance white card. Retroreflective range is specified using a BRT-250, BRT-540 or BRT-700 retroreflective target (see page 710).
Infrared Laser
Models
Serial
0.5 to 250 m
RETRO LASER
LT7PLVQ RS-422 or SSI
Class 1 Sensing Laser (Class 2 Alignment Laser)
2 PNP 4-20 mA LT7PIDQ
Lighting & Indicators Safety Light Screens Safety Laser Scanners Fiber Optic Safety Systems Safety Controllers & Modules Safety Two-Hand Control Modules Safety Interlock Switches Emergency Stop & Stop Control
ACCESSORIES
page 302

Sensing Range LT7PLVQ: 0.5 to 250 m (using specified reflector) LT7PIDQ: 6% Black card: 0.5 to 3 m 18% Gray card: 0.5 to 7 m 90% White card: 0.5 to 10 m 18 to 30V dc (10% max. ripple) Less than 4.5 W @ 25 C Infrared, 900 nm, Class 1 Measurement laser is ON when sensor is ON. Pilot (visible) laser enabled during Programming mode; alternates with measurement laser. LT7PLVQ: LT7PIDQ: Distance 10 m 50 m 100 m 250 m 4 m 6 m 10 m Spot Size 20 mm 100 mm 200 mm 500 mm 3 x 10 mm 4 x 12 mm 10 x 20 mm
LIGHT GAUGING LT3 LT7 LH LG ULTRASONIC MEASURING ARRAYS RADAR
Supply Voltage and Current Power Consumption Measuring Laser Laser Control Spot Size
Pilot Laser (Alignment) Discrete & Analog Output Protection Discrete Outputs Discrete Switch Points Discrete Output Hysteresis Alarm Outputs Analog Output Maximum Cordset Length Output Response Time Linearity Resolution/Repeatability Color Sensitivity Temperature Effect
Visible red, 650 nm, Class 2 Protected against continuous overload and short circuit (2) 100 mA, PNP Adjustable in 1 mm steps Adjustable, 10 mm min. 50 mA, PNP (NO) LT7PLVQ: None LT7PIDQ: 4-20 mA 100 m 12 milliseconds 10 mm LT7PLVQ: 2 mm LT7PLVQ: Not Applicable LT7PIDQ: 4 mm LT7PIDQ: Contact Factory
More on next page
Less than 5 mm over the total sensing range
301
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR

Minimum Analog Window Size Adjustments
(contd)
LT7PLVQ: Not Applicable LT7PIDQ: 300 mm Push-button-directed password enable/disable, measurement unit select, offset value select, output limits set, output mode select, analog output slope select (diffuse models only) and output limit manual adjust. See data sheet for information. RS-422 or SSI compatible SSI: 1.4 milliseconds (SSI cycle 80 microseconds) RS-422: 2.9 milliseconds @ 57.6 kBaud 4 LEDs: Green: Power ON/OFF Red: Alarm (Error) LED Orange: Output 1 and Output 2 conducting LEDs 2-line digital LCD display. See data sheet for detailed information.
SENSORS
Serial Interface Serial Measurement Speed Indicators
Construction Weight Environmental Rating Connections Operating Conditions Storage Temperature Vibration/Shock Application Notes
ABS shock-resistant housing; PMMA window; polycarbonate displays Approximately 230 g IEC IP67 12-pin M16 connector; 100 m max. cable length; use only cables listed on page 302. Temperature: -10 to +50 C in continuous operation -30 to +75 C EN 60947-5-2 All specifications are based on the specified surface at constant ambient conditions and following a minimum operating time of 15 minutes. For best accuracy, allow a 15-minute warmup before programming or operating Crosstalk avoidance: Light spots must be separated by at least 200 mm.
Certifications Hookup Diagrams MI05 (p. 759)
Cordsets
M16 QD
See page 697 Length
3m 10 m 30 m
Brackets
LT7
REFLECTORS
REFLECTORS
Threaded 12-Pin Straight Right-Angle

MQDC-1210ST MQDC-1230ST MQDC-1210RA MQDC-1230RA MQDC-1290RA pg. 658 SMBLT7 Additional brackets and information available. See page 620.
PAGE 710
Additional cordset information available. See page 679.
Class 1 (Infrared Sensing Laser)

Operating Mode Laser Class 1 Setup Mode Laser Class 2 Do not stare into beam
Class 2 (Visible Alignment Laser)

Lasers that emit visible radiation in the wavelength range from 400 to 700 nm where eye protection is normally afforded by aversion responses, including the blink reflex. This reaction may be expected to provide adequate protection under reasonably foreseeable conditions of operation, including the use of optical instruments for intrabeam viewing. Reference 60825-1 Amend. 2 IEC:2001(E), section 8.2.
Lasers that are safe under reasonably foreseeable conditions of operation, including the use of optical instruments for intrabeam viewing. Reference 60825-1 Amend. 2 IEC:2001(E), section 8.2.
302
L-GAGE LH
High-Precision Laser Sensors for Displacement & Thickness Measurements

Extremely accurate, robust and self-contained laser displacement sensing using a 1024 pixel CMOS linear imager Reliable and accurate measurement results on real world targets, such as machined metal, wood, ceramic, paper and painted targets Non-contact precise measurement on moving processes, hot parts, machined parts, and soft or sticky parts Precise red laser spot for easy alignment to the target Target displacement or thickness measurement with high-resolution 4-20 mA or RS-485 serial communication outputs Automatic laser power and measurement rate control for reliable measurement under changing or challenging target condition Two sensors self-synchronize for thickness measurements and thickness calculation within the sensors; no external controller required Serial communication for use of multiple sensors in multi-track or process control applications Dedicated software for sensor setup and performance monitoring
Actuators,Indicators & Illuminators
Safety Light Screens Safety Laser Scanners Fiber Optic Safety Systems Safety Controllers & Modules Safety Two-Hand Control Modules Safety Interlock Switches Emergency Stop & Stop Control
ACCESSORIES
page 304
Two sensors self-synchronize for thickness measurements and calculation within the sensors.
80 mm
DIFFUSE LASER
online
33 mm
65 mm
L-GAGE LH, 18-30V dc

Sensing Mode/LED Start of End of Spot Size at Laser Measurement Measurement Reference Measuring Reference Class Span Range Distance Range Connection Output Distance
10 mm Class 2
DIFFUSE LASER
Visible Red Laser
Models
LH30IX485QP LH80IX485QP LH150IX485QP
25 mm 60 mm 100 mm
30 mm 80 mm 150 mm
35 mm 100 mm 200 mm 8-pin Euro Pigtail QD
Analog 4-20 mA & RS-485
50 micron 125 micron 225 micron
40 mm 100 mm
Connection options: A model with a QD requires a mating cordset (see page 304).
303
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
L-GAGE LH Specifications
Sensing Beam Supply Voltage and Current Supply Protection Circuitry 670 nm (1mW) visible red IEC and CDRH Class 2 laser 18 to 30V dc (10% maximum ripple); 250 mA max @ 24V dc (exclusive of load) Protected against reverse polarity and transient over voltages 1.25 seconds 0.01% of measurement range/C 0.1% of measurement range LH30: 1 m LH80: 4 m LH15: 10 m Resolution obtained with an average of 64 readings on a white ceramic target. 3000 Lux Dynamically adjusted from 300 to 4000 Hz depending on target conditions, or locked via LH Series configurator square. None on sensor; Configuration through LH Series Configurator Software Green: Power ON; Flashing = target at reference distance Housing: Aluminum IP67 150 mm 8-pin M12/Euro-style pigtail quick-disconnect. Mating QD cordsets are ordered separately. See page 304). Analog current output: 4 to 20 mA (current sourcing) Analog output rating: 1 k max @ 24V dc, max load resistance = [(Vcc-4.5)/0.02] User adjustable output filtering via LH series configurator software. RS-485, optically isolated, up to 230 KBaud LH-Ring Serial Protocol Operating Temperature: 10 to +45 C Storage Temperature: 0 to +80 C Maximum relative humidity: 85% at +50 C, non-condensing Vibration: 60 Hz, 30 minutes, 3 axes Shock: 30G for 11 milliseconds, half sine wave, 3 axes Cover: Aluminum Orange: Target inside measurement range Cable: PVC and nickel-plated brass
SENSORS
Delay at Power-up Temperature Effect Linearity Resolution Ambient Light Measurement Frequency Adjustments Indicators Construction Environmental Rating Connections Output Configuration Output Response Serial Communication Interface Data Formats Operating Conditions Vibration and Mechanical Shock Application Notes Factory Default Settings Certifications Hookup Diagrams
Lens: Glass
Allow 30-minute warm-up for specified performance Mode: Displacement Mode Baud Rate: 115200 Sensor Address: Unset (address 0) Analog Output: 4-20 mA, positive slope, full range
MI06 (p. 759)
Cordsets
See page 689 Length
2m 5m 9m
Euro QDDouble Ended (With Shield)

See page 691 Threaded 8-Pin Straight Male to Straight Male to Straight Female Straight Male
MQLH-806-MF MQLH-815-MF MQLH-830-MF MQLH-801-MM
Euro QDSplitter
See page 692 Length Branches Trunk
2 x 0.6 m 2x0m 3 x 0.6 m 0.3 m 0.3 m 0.3 m

MQLH-806-F MQLH-815-F MQLH-830-F Additional cordset information available. See page 679.
Threaded 8-Pin
CSB-M1281M1282-LH CSB-M1281M1280-LH CSB3-M1281M1282-LH
Length
0.3 m 2m 5m 9m
Brackets
LH
Serial Adapters
See page 739
USB to RS-485 serial adapter with integral communication cordset and USB cable for easy configuration of a single sensor or a network of sensors.
Model
INTUSB485-LH
pg. 657 SMBLH1
pg. 657 SMBLH30
pg. 657 SMBLH80
pg. 657 SMBLH150
304
L-GAGE LG
Short-range Laser Sensors

Replaces large, two-piece laser gauging sensors with a completely self-contained, compact housing measuring only 55 x 82 x 20 mm Does not touch parts it measures, so can be used with moving processes, hot parts and sticky parts Houses discrete (switched) and analog outputs in the same unit, each independently programmable Automatically scales the analog output over the width of the programmed sensing window Features an outstanding maximum resolution of 3 m for flat white targets Uses an ultra-narrow beam for applications requiring precise measurement of distance, height or thickness as well as gauging applications Lets you pick the exact range you need with the push of a button Offers remote programming for added security and convenience Uses push-button programming for other output response speeds
ACCESSORIES
page 307
82.3 mm
LASER LIGHT
DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT
45.5 mm
Avoid exposure laser light emitted from this aperture

RADIANT POWER 0.2 mW 9.8KHz 11-20% DUTY CYCLE 660 - 680 nm COMPLIES WITH 21 CFR 1040.10 AND EN60825-1:1994
online
55.3 mm
DIFFUSE LASER
68.3 mm 20.2 mm
L-GAGE LG5, 12-30V dc

Sensing Beam/LED Laser Class Sensing Distance Beam Size
At 53 mm: 0.4 mm x 0.6 mm Focus: 70 mm
Visible Red Laser
Connection
2m 8-pin Euro Pigtail QD 2m 8-pin Euro Pigtail QD 2m 8-pin Euro Pigtail QD 2m 8-pin Euro Pigtail QD
Analog Output
0-10V dc
Models NPN
LG5A65NU LG5A65NUQ LG5A65NI LG5A65NIQ LG5B65NU LG5B65NUQ LG5B65NI LG5B65NIQ
Models PNP
LG5A65PU LG5A65PUQ LG5A65PI LG5A65PIQ LG5B65PU LG5B65PUQ LG5B65PI LG5B65PIQ
Class 2
DIFFUSE LASER
45-60 mm
4-20 mA
Class 2
DIFFUSE LASER
45-60 mm
At 53 mm: 0.1 mm Focus: 53 mm
0-10V dc
4-20 mA
Connection options: A model with a QD requires a mating cordset (see page 307). For 9 m cable, add suffix W/30 to the 2 m model number (example, LG5A65PU W/30).
305
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
Visible Red Laser
L-GAGE LG10, 12-30V dc

Sensing Beam/LED Laser Class Sensing Distance Beam Size
At 125 mm: 0.6 mm x 0.8 mm Focus:180 mm
Connection
2m 8-pin Euro Pigtail QD 2m 8-pin Euro Pigtail QD
Analog Output
0-10V dc
Models NPN
LG10A65NU LG10A65NUQ LG10A65NI LG10A65NIQ
Models PNP
LG10A65PU LG10A65PUQ LG10A65PI LG10A65PIQ
SENSORS
Class 2
DIFFUSE LASER
75-125 mm
4-20 mA
Connection options: A model with a QD requires a mating cordset (see page 307). For 9 m cable, add suffix W/30 to the 2 m model number (example, LG10A65PU W/30).
L-GAGE LG5 and LG10 Specifications

ACCESSORIES
Sensing Beam Supply Voltage and Current Supply Protection Circuitry Delay at Power-up Output Rating
650 nm visible Red IEC and CDRH Class 2 laser; 0.20 mW max. radiant output power 12 to 30V dc (10% max. ripple); 50 mA max @ 24V dc (exclusive of load) Protected against reverse polarity and transient overvoltages 1.25 second Discrete (switched) and Alarm outputs:100 mA max. OFF-state leakage current:less than 5 A Output saturation voltage PNP outputs:less than 1.2V at 10 mA and less than 1.6V at 100 mA NPN outputs:less than 200 mV at 10 mA and less than 600 mV at 100 mA Analog Current output:1 k max @ 24V dc, max load resistance = [(Vcc - 4.5)/0.02] Analog Voltage output: 2.5 k min. load impedance Discrete (switched) & alarm outputs:Solid-state switch; choose NPN (current sinking) or PNP (current sourcing) models Analog output:4 to 20 mA (current sourcing) or 0 to 10V dc (voltage sourcing), depending on model Discrete and alarm outputs are protected against continuous overload and short circuit Discrete Outputs (ON/OFF) Fast: 2.0 milliseconds Medium: 10 milliseconds Analog Output (-3dB) Fast: 450 Hz (1 millisecond average/1 millisecond update rate) Medium: 45 Hz (10 millisecond average/2 millisecond update rate) Slow: 4.5 Hz (100 millisecond average/5 millisecond update rate) Slow: 100 milliseconds
page 307
Output Configuration Output Protection Output Response Time
Analog Resolution and Repeatability of Discrete Trip Point* Analog Linearity* *Resolution and linearity specified @ 24V dc, 22 C, using a white ceramic test surface (see Application Notes) Minimum Window Size (Analog or Discrete) Discrete Output Hysteresis Color Sensitivity (typical) Temperature Effect Remote TEACH and Laser Control Input Impedance Remote TEACH
LG5: Fast: Less than 40 m @ 50 mm LG10: Fast: Less than 150 m @ 100 mm Medium: Less than 12 m @ 50 mm Medium: Less than 50 m @ 100 mm Slow: Less than 3 m @ 50 mm Slow: Less than 10 m @ 100 mm See chart RRC-1 on page 307 See chart RRC-2 on page 307 LG5: +/- 60 m LG10: +/- 200 m over 45 to 60 mm sensing window over 75 to 125 mm sensing window +/- 10 m +/- 20 m over 49 to 51 mm sensing window over 95 to 100 mm sensing window LG5: 1.5 mm LG5: Less than 0.2 mm LG10: 5 mm LG10: Less than 1.0 mm
LG5: Less than 75 m for white to dark gray ceramic target LG10: Less than 100 m for white to dark gray ceramic target LG5: +/- 7 m/ C 18 k min. (65 k min. at 5V dc) To teach: Connect yellow wire to +5 to 30V dc To disable: Connect yellow wire to 0 to +2V dc (or open connection)
More on next page
LG10: +/- 25 m/ C
306
L-GAGE LG5 and LG10 Specifications (contd)

Adjustments Response speed:Push button toggles between Slow, Medium, and Fast (see Output Response Time) Window limits (analog or discrete):TEACH-mode programming of near and far window limits. Limits may also be taught remotely using TEACH wire. Analog output slope:The first limit taught is assigned to the minimum analog output (0V dc or 4 mA). To enable laser: Connect green wire to +5 to 30V dc To disable laser: Connect green wire to 0 to +2V dc (or open connection) 250 millisecond delay upon enable/disable Green Power ON LED: Indicates when power is ON, overloaded output and laser status. Yellow Output LED: Indicates when discrete load output is conducting. Red Signal LED: Indicates when target is within sensing range and the condition of the received light signal. Tri-color Red/Green/Yellow TEACH LED: Indicates sensor is ready for programming each limit (indicates Red for analog output, Green for discrete, and Yellow for simultaneous analog and discrete.) Yellow Fast/Slow LEDs: Combination of 2 lights ON or OFF indicates 1 of 3 response speeds Housing: Zinc alloy die-cast, plated and painted finish Cover plate: aluminum with painted finish Lens: acrylic IP67; NEMA 6 2 m or 9 m 7-conductor shielded PVC-jacketed attached cable, or 150 mm 8-pin Euro-style pigtail quick-disconnect. Mating QD cordsets are purchased separately. See page 307. Temperature: -10 to +50 C Relative humidity: 90% at 50 C (non-condensing) Vibration: 60 Hz, 30 minutes, 3 axes Shock: 30G for 11 milliseconds, half sine wave, 3 axes For comparison, a white ceramic test surface has approximately 91% of the reflectivity of a white Kodak test card with a matte finish. A dark gray ceramic test surface has approximately 11% of the reflectivity of a white Kodak test card with a matte finish. (Allow 15-minute warm-up for maximum linearity.)
Laser Control Indicators
Construction
Environmental Rating Connections Operating Conditions Vibration and Mechanical Shock Application Notes
Certifications
LIGHT GAUGING LT3
Hookup Diagrams
NPN Models: MI06 (p. 759)
PNP Models: MI07 (p. 759)
LT7 LH LG ULTRASONIC MEASURING ARRAYS RADAR
Cordsets
See page 689 Length
2m 5m 9m
Brackets
LG5/LG10
8-Pin Threaded Straight

MQDC-806 MQDC-818 MQDC-830 Additional cordset information available. See page 679. pg. 656 SMBLG pg. 656 SMBLGA
Repeatability/Resolution Curves
= Visible Red Laser
LG5
40 35 30 25 20 15 10 5 0 45 50 55 Distance (mm) Medium Slow 60 65 Fast
Resolution/Repeatability (microns)
LG10
225 200 175 150 125 100 75 50 25 0 75 95 105 Distance (mm) 115 Slow 125 135 Medium Fast
45 Resolution/Repeatability (microns)
RRC-1
RRC-2
Range: 60 mm
Mode: Diffuse
LED:
Range: 125 mm
Mode: Diffuse
LED:
307
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
U-GAGE ULTRASONIC SENSORS

QT50U S18U QS18U T30UX/T30U
SENSORS
M25U
T18U
Q45U
Q45UR
QT50U
page 309
S18U
page 314
QS18U
page 317
T30U/T30UX
page 320
Long-range ac or dc sensor with 8 m range and minimal dead zone Advanced programming capability with a unique temperature compensation feature Retrosonic mode with a reduced dead zone Two independent near and far limits for each output Optional Teflon coating for resistance to harsh chemicals
Compact 18 mm straight or right-angle housing Highly accurate detection from 30 to 300 mm Wide range of mounting options
Compact 18 mm universal housing Compensation for air temperature fluctuations Encapsulated models for a range of harsh conditions
Right-angle T-style housing with 30 mm threaded lens Analog and discrete outputs in the same sensor A choice of programmable sensing windows, depending on response time T30UX models with temperature compensation, longer sensing ranges and shorter dead zones Optional Teflon coating for resistance to harsh chemicals
M25U
page 328
T18U
page 330
Q45U
page 332
Q45UR
page 336
Features smooth 316 stainless steel construction to withstand tough sanitary environments Rated IP69K with fully encapsulated electronics Withstands high-temperature sprays of up to 80 C and 1500 psi
Dual range, opposed ultrasonic sensors Two combinations of range and response time in the same unit Ideal for sensing under bright lighting and for clear materials T-style sensor with 18 mm threaded lens
Operating window limits from 100 mm to 3 m Discrete output models for ON/OFF presence detection or HIGH/LOW level control Programmable response time
Ultra-accurate remote gauging Compact housing with choice of three remote sensing heads Compensation for temperature variations at remote head
Teflon is a registered trademark of Dupont.
308
U-GAGE QT50U
Long-Range Ultrasonic Sensor

Senses extended range of up to 8 m Features ultrasonic dead-zone of only 2.5% of the total range75% less than comparable products Available in analog or discrete dc models and in ac/dc universal voltage models with electromechanical relay output Offers retrosonic sensing mode Features a completely sealed, shock-resistant housing that is ideal for monitoring levels of liquids as well as solids Uses a narrow sensing beam to detect targets at long range within confined areassuch as a storage tankwithout interference from the tank walls Available in a chemically resistant model with a Teflon coating to protect the transducer Features push-button programing for easy setup Provides continuous monitoring (analog model) Offers dual-discrete option for setting independent near and far limits for both outputs, for applications requiring high and low-limit sensing Compensates for temperature for greatest sensing accuracy
ACCESSORIES
page 312
Chemically resistant models

Sensor Power Indicator Output 1 Push Button
Dead Zone
200 mm Minimum Range
Target Signal Strength Indicator Output 2 Push Button
LIGHT GAUGING ULTRASONIC QT50U S18U QS18U T30U/T30UX M25U T18U Q45U Q45UR MEASURING ARRAYS RADAR
8 m Maximum Range
Output 1 Indicator
Output 2 Indicator
74.1 mm
online
84.2 mm 50.8 mm 67.4 mm
74.1 mm 73.1 mm
85.2 mm
DC and Universal Voltage Models
M56 x 1.5
Teflon-protected Models (Suffix -CRFV)
309
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
U-GAGE QT50U, 10-30V dc

Range
200 mm - 8 m
Connection
2m 5-pin Mini QD 5-pin Euro QD 2m
Output
Selectable: 0 to 10V dc or 4 to 20 mA
Models*
QT50ULB QT50ULBQ QT50ULBQ6 QT50UDB
SENSORS
200 mm - 8 m
5-pin Mini QD 5-pin Euro QD
Selectable Dual NPN or PNP
QT50UDBQ QT50UDBQ6
U-GAGE QT50U Universal Voltage, 85-264V ac/24-250V dc

Range
ACCESSORIES
Connection
2m 5-pin Micro QD 5-pin Mini QD 2m
Output Operation Mode

Window-limit (complementary outputs)
Output
SPDT e/m relay
Models*
QT50UVR3W QT50UVR3WQ1 QT50UVR3WQ
page 312
200 mm - 8 m
200 mm - 8 m
5-pin Micro QD 5-pin Mini QD
Pump/level control (pump-in and pump-out logic)
QT50UVR3F SPDT e/m relay QT50UVR3FQ1 QT50UVR3FQ
Connection options: A model with a QD requires a mating cordset (see page 312). For 9 m cable, add suffix W/30 to the 2 m model number (example, QT50ULB W/30). * For sensors with Teflon -protected face and transducer, add suffix -CRFV to the model number (example, QT50ULB-CRFV ). Teflon is a registered trademark of Dupont.
U-GAGE QT50U DC Specifications

Effective Beam Supply Voltage and Current Ultrasonic Frequency Supply Protection Circuitry Output Protection Delay at Power-up Output Configuration Output Ratings See Charts EBPC-1, EBPC-2 and EBPC-3 on page 313. Analog models: 10 - 30V dc (10% max. ripple); 100 mA max @ 10V, 40 mA max. @ 30V (exclusive of load) Dual-discrete models: 10 to 30V dc (10% max. ripple); 100 mA max. @ 10V, 40 mA @ 30V (exclusive of load) 75 kHz burst, rep. rate 96 milliseconds Protected against reverse polarity and transient overvoltages Protected against short circuit conditions 1.5 seconds Analog models: Voltage sourcing: 0 to 10V dc Current sourcing: 4 to 20 mA Dual-discrete models: Dual PNP or NPN, selectable using DIP switch Analog Voltage Output: 0 to 10V dc Minimum load resistance = 500 Minimum required supply voltage for full 0-10V output span = ( 1 0 0 0 + 13)V dc RLOAD Analog Current Output: 4 to 20 mA Maximum load resistance = 1 k or ( V supply - 5 ) , whichever is lower 0.02 Minimum required supply voltage for full 4-20 mA output span = 10V dc or [(RLoad x 0.02)+5]V dc, whichever is greater. 4-20 mA output calibrated at 25 C with 250 load. Discrete Output: 150 mA max. OFF-State leakage current: less than 5 A Output saturation: NPN: less than 200 mV @ 10 mA; less than 650 mV @ 150 mA PNP: less than 1.2V @ 10 mA; less than 1.65V @ 150 mA Uncompensated: 0.2% of distance/ C Compensated: 0.02% of distance/ C
Temperature Effect
More on next page
310
U-GAGE QT50U DC Specifications

Linearity (Analog Models) Resolution/Repeatability Hysteresis Output Response Time Minimum Window Size Adjustments Indicators 1.0 mm 5 mm
(contd)
+/- 0.2% of span from 200 to 8000 mm; +/- 0.1% of span from 500 to 8000 mm (1 mm minimum)
Analog models: 100 to 2300 milliseconds Dual-discrete models: 100 to 1600 milliseconds 20 mm Sensing window limits: TEACH-Mode programming of near and far window limits may be set using the push buttons or remotely using TEACH input. Green Power ON LED: Indicates power is ON Red Signal LED: Indicates target is within sensing range, and the condition of the received signal. Teach/Output indicator (bicolor Yellow/Red): YellowTarget is within taught limits Yellow OFF (Discrete)Target is outside taught window limits RedSensor is in TEACH mode Yellow Flashing (Analog)Target is outside taught window limits See data sheet Transducer: Ceramic/Epoxy composite Membrane Switch: Polyester Leakproof design is rated IEC IP67; NEMA 6P 2 m or 9 m shielded 5-conductor (with drain) PVC jacketed attached cable, or 5-pin Euro-style quick-disconnect or 5-pin Mini-style quick-disconnect. QD cordsets are ordered separately. See page 312. Temperature: -20 to +70 C Relative humidity: 100% All models meet Mil Std. 202F requirements. Method 201A (vibration: 10 to 60Hz max., double amplitude 0.06", maximum acceleration 10G). Also meets IEC 947-5-2 requirements: 30G 11 milliseconds duration, half sine wave Less than 0.8% of sensing distance upon power-up with Temperature Compensation enabled Objects passing inside the specified near limit (200 mm ) may produce a false response For best accuracy, allow 30 minute warm-up before programming or operating Housing: ABS/Polycarbonate Lightpipes: Acrylic
Remote TEACH Construction Environmental Rating Connections Operating Conditions Vibration and Mechanical Shock Temperature Warmup Drift Application Notes Certifications Hookup Diagrams
Analog Models: MI09 (p. 760)
Discrete Models: MI10 (p. 760)
U-GAGE QT50U Universal Voltage Specifications

Effective Beam Supply Voltage Ultrasonic Frequency Supply Protection Circuitry Output Protection Delay at Power-up Output Configuration Output Ratings See Charts EBPC-1, EBPC-2 and EBPC-3 on page 313. 85 to 264V ac, 50/60 Hz / 24 to 250V dc (1.5 watts max., exclusive of load) 75 kHz burst, rep. rate 96 milliseconds. Protected against transient over voltages. DC hookup is without regard to polarity. Protected against short circuit conditions 1.5 seconds SPDT (Single-Pole, Double-Throw) electromechanical relay output. One normally open (NO) and one normally closed (NC). Max. switching power (resistive load): 2000 VA, 240 W (1000 VA, 120 W for sensors with Micro QD) Max. switching voltage (resistive load): 250V ac, 125V dc Max. switching current (resistive load): 8A @ 250V ac, 8A @ 30V dc derated to 200 mA @ 125V dc (4A max. for sensors with Micro QD) Min. voltage and current: 5V dc, 10 mA Mechanical life of relay: 50,000,000 operations Electrical life of relay at full resistive load: 100,000 operations NOTE: Transient suppression is recommended when switching inductive loads. Temperature Effect Repeatability Uncompensated: 0.2% of distance/ C 1.0 mm Compensated: 0.02% of distance/ C
More on next page
311
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
U-GAGE QT50U Universal Voltage Specifications

Hysteresis Output Response Time Minimum Window Size Window-limit sensor models: 5 mm Selectable 1600, 400 or 100 milliseconds 20 mm
(contd)
Fill-level control sensor models: 0 mm
SENSORS
Adjustments
Sensing limits: TEACH-Mode programming of near and far limits may be set using the TEACH push button. Sensor configuration: Output response time and temperature compensation mode may be set using the Speed push button. Factory default settings: 4 00 milliseconds output response time; temperature compensation enabled Green Power ON LED: Indicates power is ON Red Signal LED: Indicates target is within sensing range, and the condition of the received signal. Output indicator (bicolor Yellow/Red): Indicates output status or TEACH mode Response indicator (bicolor Yellow/Red): Indicates output response time selection Transducer: Ceramic/Epoxy composite Membrane Switch: Polyester Leakproof design is rated IEC IP67; NEMA 6P 2 m or 9 m shielded 5-conductor (with drain) PVC jacketed attached cable, or 5-pin Micro-style quick-disconnect or 5-pin Mini-style quick-disconnect. QD cordsets are ordered separately. See page 312. Temperature: -20 to +70 C Relative humidity: 100% Housing: ABS
Indicators
Construction Environmental Rating Connections Operating Conditions Vibration and Mechanical Shock Temperature Warmup Drift Application Notes Certifications Hookup Diagrams
All models meet Mil Std. 202F requirements. Method 201A (vibration: 10 to 60Hz max., double amplitude 0.06", maximum acceleration 10G). Also meets IEC 947-5-2 requirements: 30G 11 milliseconds duration, half sine wave Less than 1.0% of sensing distance upon power-up with Temperature Compensation enabled Objects passing inside the specified minimum sensing distance (200 mm) may produce a false response.
UN09 (p. 755)
Cordsets
See page 687 Length
2m 5m 9m
Micro QD (With Shield)

See page 699 Length
2m 5m 10 m
Mini QD (With Shield)

See page 701 Length
2m 4m 10 m

MQDEC2-506 MQDEC2-515 MQDEC2-530 MQDEC2-506RA MQDEC2-515RA MQDEC2-530RA

MQVR3S-506 MQVR3S-515 MQVR3S-530 MQVR3S-506RA MQVR3S-515RA MQVR3S-530RA

MBCC2-506 MBCC2-512 MBCC2-530
Brackets
QT50U
pg. 639 SMB30A
pg. 640 SMB30MM
pg. 641 SMB30SC
312
Effective Beam Patterns

QT50U (Typical) QT50U (with 500 mm Plate) Maximum Target Rotation Angle
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors Measurement & Inspection Sensors Vision Wireless Lighting & Indicators Safety Light Screens Safety Laser Scanners Fiber Optic Safety Systems Safety Controllers & Modules Safety Two-Hand Control Modules
1000 mm 800 mm 600 mm
25 mm Rod 500 mm Plate
40 30 20
Target Rotation
400 mm
Lateral Distance
200 mm 0 -200 mm -400 mm -600 mm -800 mm -1000 mm 0 1m 2m 3m 4m 5m 6m 7m 8m
10 0 -10 -20 -30 -40 0 1m 2m 3m 4m 5m 6m 7m 8m
Target Distance
Target Distance
EBPC-1
EBPC-2
Safety Interlock Switches Emergency Stop & Stop Control
QT50U Teflon-Encapsulated (Typical)
1000 mm 800 mm 600 mm 400 mm
25 mm Rod
LIGHT GAUGING ULTRASONIC QT50U S18U

500 mm Plate
Lateral Distance
200 mm 0 -200 mm -400 mm -600 mm -800 mm -1000 mm 0 1m 2m 3m 4m 5m 6m 7m 8m
QS18U T30U/T30UX M25U T18U Q45U Q45UR MEASURING ARRAYS RADAR
Target Distance
EBPC-3
313
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
U-GAGE S18U
SENSORS
ACCESSORIES
Compact Barrel-Mount Ultrasonic Sensor

Senses from 30 to 300 mm Available in analog or discrete models Features minimal dead zone and eliminates dead zone if used in retrosonic mode Ideal for material handling and packaged goods applications, such as bottling or liquid level detection and control for small containers Available in straight or right-angle versions with a wide variety of mounting hardware for enhance sensing versatility Offers programmable background suppression Compensates for temperature for greatest sensing accuracy Simplifies setup with push-button and remote TEACH-mode programming Shows status during setup and operation, using highly visible LEDs indicators
page 316
Accessory wave guides are available for narrowing sensing beam. (see page 316) 80.8 mm
85.1 mm
online
18.0 mm
18.0 mm
Straight Models
S18U Right-Angle Models
U-GAGE S18U, 10-30V dc

Range Connections
2m 30 - 300 mm 5-pin Euro QD 2m 5-pin Euro QD 2m 30 - 300 mm 5-pin Euro QD 2m 5-pin Euro QD 2m 30 - 300 mm 5-pin Euro QD 2m 5-pin Euro QD
Connection options: A model with a QD requires a mating cable (see page 316). For 9 m cable, add suffix W/30 to the 2 m model number (example, S18UUA W/30).
Output
0 to 10V dc
Housing Configuration
Models
S18UUA S18UUAQ S18UIA S18UIAQ S18UUAR
Straight 4 to 20 mA
0 to 10V dc Right-Angle 4 to 20 mA
S18UUARQ S18UIAR S18UIARQ
Straight Bipolar NPN/PNP Right-Angle
S18UBA S18UBAQ S18UBAR S18UBARQ
314
U-GAGE S18U Specifications

Effective Beam Supply Voltage and Current Ultrasonic Frequency Supply Protection Circuitry Output Protection Output Ratings See Charts EBPC-1 and EBPC-2 on page 316. 10 to 30V dc (10% max. ripple); 65 mA max. (exclusive of load), 40 mA typical @ 25V input 300 kHz, rep. rate 2.5 milliseconds Protected against reverse polarity and transient voltages Protected against short circuit conditions Analog: Analog Voltage Output: 2.5 k min. load resistance Minimum supply for a full 10V output is 12V dc (for supply voltages between 10 and 12, V out max is at least V supply -2) Analog Current Output: 1 k max @ 24V input Max load resistance = (Vcc-4)/0.02 Discrete: 100 mA max. OFF-state leakage current: less than 5 A NPN saturation: less than 200 mV @ 10 mA and less than 600 mV @ 100 mA PNP saturation: less than 1.2V @ 10 mA and less than 1.6V @ 100 mA Analog: 0 to 10V dc or 4 to 20 mA, depending on model Discrete: Bipolar: One NPN (current sinking) and one PNP (current sourcing) output in each model. Solid-state switch conducts when target is sensed within sensing window. Analog: 30 milliseconds: Black wire at 0-2V dc (or open) 2.5 milliseconds: Black wire at 5-30V dc 300 milliseconds 2.5 milliseconds response: 1 mm 30 milliseconds response: 0.5 mm 2.5 milliseconds response: 1 mm 30 milliseconds response: 0.5 mm 0.5 mm 0.02% of distance/ C Less than 1.7% of sensing distance upon power-up 5 mm 0.7 mm Sensing window limits: TEACH-Mode programming of near and far window limits may be set using the push-button or remotely using TEACH input. Power/Signal Strength (Red/Green) GreenTarget is within sensing range RedTarget is outside sensing range OFFSensing power is OFF Teach/Output Indicator (Yellow/Red) Yellow Target is within taught limits OFFTarget is outside taught window limits RedSensor is in TEACH mode Remote TEACH Input Construction Environmental Rating Connections Operating Conditions Impedance: 12 k Threaded Barrel: Thermoplastic polyester Push Button: Santoprene Leakproof design is rated IEC IP67; NEMA 6P 2 m or 9 m shielded 5-conductor (with drain) PVC jacketed attached cable, or 5-pin Euro-style quick-disconnect. QD cordsets are ordered separately. See page 316. Temperature: -20 to +60 C Relative humidity: 100% Push-Button Housing: ABS/PC Lightpipes: Acrylic Discrete: 5 milliseconds
Output Response Time Delay at Power-up Linearity* (Analog output models) Resolution* (Analog output models) Repeatability (Discrete models) Temperature Effect Temperature Warmup Drift Minimum Window Size Switching Hysteresis (Discrete output models) Adjustments Indicators
More on next page
*Linearity and resolution are specified using a 50 x 50 mm aluminum plate at 22 C under fixed sensing conditions.
315
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
U-GAGE S18U Specifications (contd)

Vibration and Mechanical Shock Application Notes All models meet Mil. Std. 202F requirements. method 201A (vibration: 10 to 60 Hz max., double amplitude 0.06, maximum acceleration 10G). Also meets IEC 947-5-2 requirements: 30G 11 milliseconds duration, half sine wave Objects passing inside the specified near limit may produce a false response.
SENSORS
Certifications Hookup Diagrams Analog Models: MI11 (p. 760) Discrete Models: MI10 (p. 760)
Cordsets
See page 687 Length
2m 5m 9m
Brackets
S18U
Ultrasonic Wave Guides

Inside Diameter
5.0 mm
Model
UWG18-5.0

MQDEC2-506 MQDEC2-515 MQDEC2-530 MQDEC2-506RA MQDEC2-515RA MQDEC2-530RA pg. 637 SMB18A pg. 638 SMB18FM pg. 638 SMB18SF pg. 737
6.4 mm
UWG18-6.4

S18U (Typical)
2.25 mm rod 8 mm rod 50 mm x 50 mm
S18U (with 500 mm Plate) Maximum Target Rotation Angle
20 mm 15 mm
15
Aluminum target used: 50 mm x 50 mm
Lateral Distance
10 mm 5 mm 0 -5 mm -10 mm -15 mm -20 mm 0 50 mm 100 mm 150 mm 200 mm 250 mm 300 mm
Target Rotation
10 5 0 -5 -10 -15 0 50 mm 100 mm 150 mm 200 mm 250 mm 300 mm
Sensing Distance
Sensing Distance
EBPC-1
EBPC-2
316
QS18U
Ultrasonic WORLD-BEAM Sensor

Features a universal housing with an 18 mm threaded lens or side mounts Senses clear or transparent material and color variations, including clear web material, clear or shiny bottles, highly reflective surfaces and liquid or dry bulk materials from inside cramped locations Senses within a 50 to 500 mm window with a 15 millisecond response time Delivers high accuracy in wet or dirty environments Available in encapsulated IP68 models rated for a range of harsh conditions Features push-button TEACH for easy programming at the sensor or remotely Featuring wide operating range of -20 to +60 C Offers retrosonic sensing mode Delivers bright LED operating indicators visible from 360
ACCESSORIES
15.0 mm
page 319
33.5 mm 41.5 mm 24.1 mm

LIGHT GAUGING ULTRASONIC QT50U S18U QS18U T30U/T30UX
online
M25U
Accessory wave guides are available for narrowing sensing beam. (see page 319)
T18U Q45U Q45UR MEASURING ARRAYS RADAR
WORLD-BEAM QS18U, 12-30V dc

Range
50 - 500 mm 4-pin Euro QD 2m 50 - 500 mm 4-pin Euro QD
Connection
2m
TEACH Options
Integral push button and remote TEACH (IP67; NEMA 6P) Remote TEACH (epoxy-encapsulated, IP68; NEMA 6P)
Models NPN
QS18UNA QS18UNAQ8 QS18UNAE QS18UNAEQ8
Models PNP
QS18UPA QS18UPAQ8 QS18UPAE QS18UPAEQ8
Connection options: A model with a QD requires a mating cordset (see page 319). For 9 m cable, add suffix W/30 to the 2 m model number (example, QS18UNA W/30). QD models: For 4-pin integral Euro-style QD, add suffix Q8 (example, QS18UNAQ8). For 4-pin 150 mm Euro-style pigtail, add suffix Q5 (example, QS18UNAQ5). For 4-pin integral Pico-style QD, add suffix Q7 (example, QS18UNAQ7). For 4-pin 150 mm Pico-style pigtail, add suffix Q (example, QS18UNAFQ).
Models are epoxy-encapsulated, IP68; NEMA 6P with remote TEACH programming
317
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
WORLD-BEAM QS18U Specifications

Effective Beam Sensing Range Supply Voltage and Current See Charts EBPC-1 and EBPC-2 on page 319. 50 to 500 mm 12 to 30V dc (10% max. ripple); 25 mA max. (exclusive of load) 300 kHz, rep. rate 7.5 milliseconds Protected against reverse polarity and transient voltages Protected against short circuit conditions 300 milliseconds Solid-state switch conducts when target is sensed within sensing window; one NPN (current sinking) or one PNP (current sourcing), depending on model. Non-encapsulated models: 0.05% per C from -20 to +50 C, 0.1% per C from +50 to +60 C Encapsulated models: 0.05% per C from 0 to +60 C, 0.1% per C from -20 to 0 C 0.7 mm 1.4 mm 100 mA max. (see Application Note 1) OFF-state leakage current: less than 10 A (sourcing); less than 200 A (sinking); See Application Note 2 NPN ON-statesaturation voltage: less than 1.6V @ 100 mA PNPON-statesaturation voltage: less than 2.0V @ 100 mA 15 milliseconds 5 mm Sensing window limits: TEACH-Mode programming of near and far window limits may be set using the push button or remotely using TEACH input. Range Indicator (Red/Green) GreenTarget is within sensing range RedTarget is outside sensing range OFFSensing power is OFF Housing: ABS Push Button: TPE Teach/Output Indicator (Yellow/Red) YellowTarget is within taught limits OFFTarget is outside taught window limits RedSensor is in TEACHmode Push-Button Housing: ABS Lightpipes: Polycarbonate
SENSORS
Ultrasonic Frequency Supply Protection Circuitry Output Protection Delay at Power-Up Output Configurations Temperature Effect Repeatability Hysteresis Output Ratings
Output Response Time Minimum Window Size Adjustments Indicators
Construction Environmental Rating Connections Operating Conditions Vibration and Mechanical Shock Temperature Warmup Drift Application Notes
Leakproof design, rated IEC IP67 or IP68; NEMA 6P, depending on model; UL type 1 2 m or 9 m 4-conductor PVC jacketed attached cable, or 4-pin Euro-style integral QD (Q8), or 4-pin Pico-style integral QD (Q7), or 4-pin Euro-style 150 mm pigtail QD (Q5), or 4-pin Pico-style 150 mm pigtail QD (Q), depending on model. See page 319. Temperature: -20 to +60 C Relative humidity: 100% (non-condensing)
All models meet Mil. Std. 202F requirements method 201A (vibration: 10 to 60 Hz max., double amplitude 0.06", maximum acceleration 10G). Also meets IEC 947-5-2 requirements: 30G 11 milliseconds duration, half sine wave. See data sheet 1. If supply voltage is > 24V dc, derate maximum output current 5 mA/C above 50C. 2. N PN OFF-state leakage current is < 200 A for load resistances > 3 k or optically isolated loads. For load current of 100 mA, leakage is < 1% of load current. 3. Objects passing inside the specified near limit may produce a false response.
318
Cordsets
Pico QD (With Shield)
See page 681 Length
2m
Brackets
See page 683 Length
2m 5m 9m
QS18U
Snap-On 4-Pin Straight Right-Angle

PKG4S-2 PKW4ZS-2

MQDEC2-406 MQDEC2-415 MQDEC2-430 MQDEC2-406RA MQDEC2-415RA MQDEC2-430RA pg. 637 SMB18A pg. 638 SMB18FA.. pg. 638 SMB18SF
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors Measurement & Inspection Sensors Vision Wireless Lighting & Indicators Safety Light Screens Safety Laser Scanners Fiber Optic Safety Systems Safety Controllers & Modules Safety Two-Hand Control Modules Safety Interlock Switches
Ultrasonic Wave Guides

Inside Diameter
5.0 mm
Model
UWG18-5.0
Emergency Stop & Stop Control
pg. 709
6.4 mm
UWG18-6.4
LIGHT GAUGING ULTRASONIC QT50U S18U QS18U T30U/T30UX M25U

QS18U (Typical)
2.5 mm rod 8 mm rod 50 mm x 50 mm plate
T18U Q45U
QS18U Maximum Target Rotation Angle
Q45UR MEASURING ARRAYS RADAR
50 mm 40 mm 30 mm
15
Lateral Distance
20 mm 10 mm 0 -10 mm -20 mm -30 mm -40 mm -50 mm 0 100 mm 200 mm 300 mm 400 mm 500 mm
Target Rotation
10 5 0 -5 -10 -15 0 100 mm 200 mm 300 mm 400 mm 500 mm
Sensing Distance
Sensing Distance
EBPC-1
EBPC-2
319
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
U-GAGE T30UX/T30U
SENSORS
ACCESSORIES
Compact Sensors in Universal Housing

Features T-style right-angle sensor package with popular 30 mm threaded barrel and a wide variety of mounting brackets Offers choice of three ranges for reliable sensing from 100 mm to 3 m Includes models with a single analog or single discrete, two discrete, or analog and discrete in the same sensor Simplifies setup with push-button TEACH programming of custom sensing window Allows remote programming with an external switch, computer or controller for added security and convenience Presents sensor operating status using highly visible indicators LEDs Resists harsh environments with rugged IP67 (NEMA 6) housing and fully encapsulated electronics Provides digital filtering for exceptional electrical and noise immunity
page 325
T30UX
Built-in temperature compensation for high-accuracy across a wide range of ambient temperatures Extended sensing ranges and short dead zones with 100 mm to 1 m, 200 mm to 2 m or 300 mm to 3 m Models with either analog or configurable discrete output Analog output models for applications requiring a continuous current or voltage output Wide operating temperature range of -40 to +70 C
T30U
Range of 150 mm to 1 m or 300 mm to 2 m, depending on model Models with either dual-discrete or analog/discrete outputs Dual-discrete models for ON/OFF switching or pump/level control Independently programmable outputs Analog output models for applications requiring a continuous current or voltage output Chemically resistant models with a Teflon coating to protect the transducer
U-GAGE T30UX/T30U Sensors

40.0 mm
online
45.0 mm
40.0 mm
48.3 mm
51.5 mm
63.7 mm
45.0 mm 51.5 mm
30.0 mm
M36 x 1.5
T30UX and T30U (Long-range) Models
T30U Teflon-protected Models Suffix -CRFV
T30U (Short-range) Models
320
U-GAGE T30UX, 10-30V dc

Range
100 mm to 1 m
Frequency
224 kHz
Connection
2m 4-Pin Euro QD 2m 4-Pin Euro QD 2m 4-Pin Euro QD 2m
Response Time
45 ms
Output
Models*
T30UXDA T30UXDAQ8
ACCESSORIES
200 mm to 2 m
174 kHz
92 ms
Discrete: NPN, PNP, NO, NC, Selectable
T30UXDB T30UXDBQ8 T30UXDC T30UXDCQ8
300 mm to 3 m
114 kHz
135 ms
100 mm to 1 m
224 kHz
4-Pin Euro QD 2m 4-Pin Euro QD 2m
Analog: 0 to 10V dc Selectable 45 or 105 ms Analog: 4 to 20 mA
T30UXUA T30UXUAQ8 T30UXIA T30UXIAQ8 T30UXUB T30UXUBQ8 T30UXIB T30UXIBQ8 T30UXUC T30UXUCQ8 T30UXIC T30UXICQ8
200 mm to 2 m
174 kHz
4-Pin Euro QD 2m 4-Pin Euro QD 2m
page 325
300 mm to 3 m
114 kHz
4-Pin Euro QD 2m 4-Pin Euro QD
Connection options: A model with a QD requires a mating cordset (see page 325). For 9 m cable, add suffix W/30 to the 2 m model number (example, T30UXDA W/30). QD models: For a 4-pin 150 mm Euro-style PUR pigtail QD, add suffix QPMA the 2 m model number (example, T30UXDAQPMA). * Contact factory to request chemically resistant flange or fill-level control models.
U-GAGE T30U, 12-24V dc

Range Frequency Connection
2m 150 mm - 1 m 228 kHz 5-pin Euro QD 2m 5-pin Euro QD 2m 300 mm - 2 m 128 kHz 5-pin Euro QD 2m 5-pin Euro QD 2m 150 mm - 1 m 228 kHz 5-pin Euro QD 2m 5-pin Euro QD
Connection options: A model with a QD requires a mating cordset (see page 325). For 9 m cable, add suffix W/30 to the 2 m model number (example, T30UINA W/30). *
Response Time
Discrete Output(s)
NPN
Analog Output
Models*
T30UINA T30UINAQ T30UIPA T30UIPAQ T30UINB T30UINBQ T30UIPB T30UIPBQ T30UDNA T30UDNAQ T30UDPA T30UDPAQ
48 ms PNP NPN 96 ms PNP Dual NPN 48 ms Dual PNP
4 to 20 mA
4 to 20 mA
None
For sensors with Teflon -protected face and transducer (long-range models only), add suffix -CRFV to the model number (example, T30UINB-CRFV ). Teflon -encapsulated models have a range of 300 mm - 1.5 m. Teflon is a registered trademark of Dupont.
321
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR

Range Frequency Connection
2m 5-pin Euro QD 2m 5-pin Euro QD 150 mm - 1 m 300 mm - 2 m 150 mm - 1 m 300 mm - 2 m 228 kHz 128 kHz 228 kHz 128 kHz 2m 5-pin Euro QD 2m 5-pin Euro QD 2m 5-pin Euro QD 2m 5-pin Euro QD 48 ms 96 ms 48 ms 96 ms
Response Time
Discrete Output(s)
Dual NPN
Analog Output
Models*
T30UDNB T30UDNBQ T30UDPB T30UDPBQ T30UHNA T30UHNAQ T30UHNB T30UHNBQ T30UHPA
SENSORS
300 mm - 2 m
128 kHz
96 ms Dual PNP
None
Pump/Level Control Dual NPN
None
Pump/Level Control Dual PNP
None
T30UHPAQ T30UHPB T30UHPBQ
Connection options: A model with a QD requires a mating cordset (see page 325).
ACCESSORIES
page 325
For 9 m cable, add suffix W/30 to the 2 m model number (example, T30UDNB W/30). *
For sensors with Teflon -protected face and transducer (long-range models only), add suffix -CRFV to the model number (example, T30UDNB-CRFV ). Teflon -encapsulated models have a range of 300 mm - 1.5 m.

Range
150 mm - 1 m
Frequency
228 kHz
Connection
Response Time
48 ms
Analog Output
0 to 10V dc
Models* NPN
T30UUNA T30UUNAQ T30UUNB T30UUNBQ
Models* PNP
T30UUPA T30UUPAQ T30UUPB T30UUPBQ
300 mm - 2 m
128 kHz
96 ms
0 to 10V dc
Connection options: A model with a QD requires a mating cordset (see page 325). For 9 m cable, add suffix W/30 to the 2 m model number (example, T30UUNA W/30). *
For sensors with Teflon -protected face and transducer (long-range models only), add suffix -CRFV to the model number (example, T30UUNB-CRFV ). Teflon -encapsulated models have a range of 300 mm - 1.5 m.
U-GAGE T30UX Specifications

Effective Beam Sensing Range See Chart EPBC-1 to EPBC-6 on page 326. A suffix models: 100 mm to 1 m B suffix models: 200 mm to 2 m C suffix models: 300 mm to 3 m A suffix models: 224 kHz B suffix models: 174 kHz C suffix models: 114 kHz 10 to 30V dc (10% max. ripple) at 40 mA, exclusive of load Protected against reverse polarity and transient voltages. Discrete (switched) output models: SPST solid-state switch. Configurable as NPN (sinking) or PNP (sourcing) via Mode push button. Normally Open (NO) or Normally Closed (NC) operation is also selectable via Mode push button. The default setting is PNP/NO. Analog output models: 0 to 10V dc or 4 to 20 mA, depending on model
Ultrasonic Frequency
Supply Voltage and Current Supply Protection Circuitry Output Configuration
More on next page
322
U-GAGE T30UX Specifications

Output Ratings Discrete output models: 100 mA max. OFF-state leakage current: NPN: < 200 A @ 30V dc (see NOTE 1) ON-state saturation voltage: NPN: < 1.6V @ 100 mA PNP: < 10 A @ 30V dc PNP: < 3V @ 100 mA
Analog output models: Analog Voltage Output: 2.5 k min. load resistance Minimum supply for a full 10V output is 12V dc (for supply voltages between 10 and 12, V out max. is at least V supply -2) Analog Current Output: 1 k max. @ 24V input; max. load resistance = (Vcc-4)/0.02 For current output (4-20 mA) models, ideal results are achieved when the total load resistance R = [(Vin 4)/0.020]. Example, at Vin = 24V dc, R 1 k (1 watt) Output Protection Circuitry Output Response Time Protected against short circuit conditions A suffix models: 45 milliseconds B suffix models: 92 milliseconds C suffix models: 135 milliseconds 500 milliseconds 0.02% of distance/ C 0.25% of distance A suffix models: 0.1% of distance (0.5 mm min.) B suffix models: 0.1% of distance (1.0 mm min.) C suffix models: 0.1% of distance (1.5 mm min.) A suffix models: 2 mm B suffix models: 3 mm C suffix models: 4 mm 10 mm Sensing window limits: TEACH-Mode configuration of near and far window limits may be set using the push button or remotely viaTEACH input Discrete output models: Output Configuration: NPN, PNP, Normally Open (NO), Normally Closed (NC) select Advanced configuration options: Push button enabled/disabled, temperature compensation enabled/disabled Analog output models: Response speed selection: Fast or Slow Advanced configuration options: Analog output slope, push button enabled/disabled, temperature compensation enabled/disabled Green Power LED ON: Power ON, RUN mode Red Signal LED: Target signal strength Amber Output LED: Output enabled; sensor receiving a signal within the window limits Amber Mode LED: Currently selected mode 0 to 10V dc models: Analog output goes to 0V 4 to 20 mA models: Analog output goes to 3.6 mA Housing: PBT polyester Push buttons: polyester Transducer: epoxy /ceramic composite Leakproof design, rated IEC IP67 (NEMA 6) 2 m or 9 m shielded 4-conductor (with drain) PVC cable, 150 mm PUR Euro-style pigtail (QPMA), or 4-pin integral Euro-style connector (Q8). QD cordsets ordered separately. See page 325. Temperature: -40 to +70 C Relative humidity: 95% at 50C non-condensing
Delay at Power-up Temperature Effect Linearity (analog models) Repeatability/Resolution
Sensing Hysteresis (discrete models) Minimum Window Size Adjustments
Indicators
Loss of Signal Indication (analog models) Construction
Environmental Rating Connections Operating Conditions Vibration and Mechanical Shock Application Notes Certifications Hookup Diagrams
All models meet Mil. Std. 202F requirements. Method 201A (Vibration: 10 to 60Hz max., double amplitude 0.06", maximum acceleration 10G). Also meets IEC 947-5-2 requirements: 30G, 11 milliseconds duration, half sine wave. The temperature warmup drift upon power-up is less than 1% of the sensing distance.
Discrete Models: MI13 (p. 761) Analog Models: MI14 (p. 761)
NOTE 1: NPN < 200 A for load impedance > 3 k; for load current of 100 mA, leakage < 1% of load current
323
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
U-GAGE T30U Specifications

Effective Beam Sensing Range See Chart EPBC-7 to EPBC-11 on page 327. A suffix models: 150 mm min. near limit; 1 m max. far limit B suffix models: 300 mm min. near limit; 2 m max. far limit -CRFV models: 300 mm min. near limit; 1.5 m max. far limit Current sourcing analog output models: 12 to 24V dc (10% max. ripple); 90 mA (exclusive of load) Voltage sourcing analog output models: 15 to 24V dc (10% max. ripple); 90 mA (exclusive of load) Dual-discrete output models: 12 to 24V dc (10% max. ripple); 90 mA (exclusive of load) Short Range: 228 kHz Long Range: 128 kHz Protected against reverse polarity and transient voltages. Protected against continuous overload and short-circuit; transient over-voltage; no false pulse on power-up. Discrete (switched) output: Solid-state switch conducts when target is sensed within sensing window; choose NPN (current sinking) or PNP (current sourcing) models. Analog output: C hoose 0 to 10V dc sourcing or 4 to 20 mA sourcing output models; output slope may be selected using TEACH sequence. Discrete (switched) output: 100 mA max., totalboth outputs OFF-state leakage current: less than 10 A ON-state saturation voltage: less than 1V at 10 mA and less than 1.5V at 100 mA Analog Output: Voltage sourcing: 0 to 10V dc (at 1 k min. resistance) Current sourcing: 4 to 20 mA, 1 to Rmax. Output Response Time Rmax = Vsupply - 7V 20 mA
SENSORS
Supply Voltage and Current
Ultrasonic Frequency Supply Protection Circuitry Output Protection Output Configuration
Output Ratings
Discrete output: A suffix models: 48 milliseconds B suffix models: 96 milliseconds Analog output: A suffix models: 48 milliseconds average, 16-millisecond update B suffix models: 96 milliseconds average, 32-millisecond update Analog sensing resolution or discrete output repeatability: 0.25% of measured distance A suffix models: .5 mm min B suffix models: 1 mm min Analog linearity: 0.5% of full-scale span Min. window size: 10 mm Hysteresis of discrete output: 2.5 mm Temperature effect: 0.2% of sensing distance per C Sensing window limits (analog or discrete): TEACH-mode programming of near and far window limits may be set using membrane push buttons on sensor or remotely using TEACH input. Window limits may be programmed separately, or together. Analog output slope: the first limit taught is assigned to the minimum output value (4 mA or 0V). Four status LEDs: In RUN mode: Green ON Steady: Power ON, RUN mode Green Flashing: Discrete output is overloaded Red Flashing: Relative received signal strength Yellow analog ON Steady: Target is inside window limits Yellow discrete ON Steady: Output conducting In Program mode: Green OFF: PROGRAM mode Red Flashing: Relative received signal strength Yellow ON Steady: Ready for first window limit Yellow Flashing: Ready for second limit Yellow OFF: Not teaching this output Molded reinforced thermoplastic polyester housing. Leakproof design is rated IEC IP67; NEMA 6P 2 m or 9 m 5-conductor PVC-covered attached cable, or 5-pin Euro-style quick-disconnect fitting. QD cordsets are ordered separately. See page 325. Temperature: -20 to +70 C Relative humidity: 100%
Sensing Performance (Specified using a 100 x 100 mm aluminum target at 25 C under fixed sensing conditions.)
Adjustments
Indicators
Construction Environmental Rating Connections Operating Conditions
More on next page
324
U-GAGE T30U Specifications (contd)

Vibration and Mechanical Shock Application Notes Certifications Hookup Diagrams All models meet Mil. Std. 202F requirements. Method 201A (Vibration: 10 to 60Hz max., double amplitude 0.06", maximum acceleration 10G). Also meets IEC 947-5-2 requirements: 30G, 11 milliseconds duration, half sine wave. Objects passing inside the specified near limit will produce a false response. NOTE: For more information about out-of-range and signal loss response of the analog output, see product literature.
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors Measurement & Inspection Sensors Vision Wireless Lighting & Indicators
Analog/Discrete Models: MI16 (p. 761) Dual-Discrete Models: MI15 (p. 761)
Safety Light Screens Safety Laser Scanners Fiber Optic Safety Systems Safety Controllers & Modules
Cordsets
See page 683 Length
2m 5m 9m
Brackets
T30UX/T30U
MQDEC2-506 MQDEC2-515 MQDEC2-530 MQDEC2-506RA MQDEC2-515RA MQDEC2-530RA pg. 637 SMB1815SF pg. 639 SMB30A pg. 640 SMB30FA..

Additional brackets and information available. See page 620. LIGHT GAUGING ULTRASONIC QT50U S18U QS18U T30U/T30UX M25U T18U Q45U Q45UR MEASURING ARRAYS RADAR
325
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR

T30UX with Plate Target (Typical) 1-Meter Models
200 mm 8.0" 6.0" 100 x 100 mm 4.0" 2.0" 0 2.0" 4.0" 6.0" 0 200 mm (8.0") 400 mm (16.0") 600 mm (24.0") Distance 800 mm (32.0") 8.0" 1000 mm (40.0")
T30UX with Rod Target (Typical) 1-Meter Models

200 mm 150 mm 100 mm 50 mm Width 0 50 mm 100 mm 150 mm 200 mm 0 200 mm (8.0") 400 mm (16.0") 600 mm (24.0") Distance 800 mm (32.0") 25 mm Rod 10 mm Rod 8.0" 6.0" 4.0" 2.0" 0 2.0" 4.0" 6.0" 8.0" 1000 mm (40.0")
SENSORS
150 mm 100 mm 50 mm Width 0 50 mm 100 mm 150 mm 200 mm
EBPC-1
EBPC-2

400 mm 300 mm 200 mm 100 mm Width 0 100 mm 200 mm 300 mm 400 mm 0 400 mm (16.0") 800 mm (32.0") 1200 mm (48.0") Distance 1600 mm (64.0" 100 x 100 mm 16.0" 12.0" 8.0" 4.0" 0 4.0" 8.0" 12.0" 16.0" 2000 mm (80.0")

400 mm 300 mm 200 mm 100 mm Width 0 100 mm 200 mm 300 mm 400 mm 0 400 mm (16.0") 800 mm (32.0") 1200 mm (48.0") Distance 1600 mm (64.0") 10 mm Rod 25 mm Rod 16.0" 12.0" 8.0" 4.0" 0 4.0" 8.0" 12.0" 16.0" 2000 mm (80.0")
EBPC-3
EBPC-4

400 mm 300 mm 200 mm 100 mm Width 0 100 mm 200 mm 300 mm 400 mm 0 600 mm (24.0") 1200 mm (48.0") 1800 mm (72.0") 2400 mm (96.0") 100 x 100 mm 16.0" 12.0" 8.0" 4.0" 0 4.0" 8.0" 12.0" 16.0" 3000 mm (120.0")

400 mm 300 mm 200 mm 100 mm Width 0 100 mm 200 mm 300 mm 400 mm 0 600 mm (24.0") 1200 mm (48.0") 1800 mm (72.0") 2400 mm (96.0") 10 mm Rod 25 mm Rod 16.0" 12.0" 8.0" 4.0" 0 4.0" 8.0" 12.0" 16.0" 3000 mm (120.0")
Distance
Distance
EBPC-5
EBPC-6
More on next page
326

T30U with Plate Target (Typical) 1-Meter Models
200 mm 150 mm 100 mm 100 x 100 mm 10 x 10 mm
T30U with Rod Target (Typical) 1-Meter Models

200 mm 150 mm 100 mm
Lateral Distance
50 mm 0 50 mm 100 mm 150 mm 200 mm
Lateral Distance
50 mm 0 50 mm 100 mm 150 mm 200 mm
25 mm Rod 10 mm Rod
Lighting & Indicators Safety Light Screens Safety Laser Scanners Fiber Optic Safety Systems
200 mm
400 mm
600 mm
800 mm
1000 mm
200 mm
400 mm
600 mm
800 mm
1000 mm
Safety Controllers & Modules Safety Two-Hand Control Modules Safety Interlock Switches Emergency Stop & Stop Control
Target Distance
Target Distance
EBPC-7
EBPC-8
T30U with Plate Target (Typical) 2-Meter Models

400 mm 300 mm 200 mm
T30U with Rod Target (Typical) 2-Meter Models

400 mm 300 mm 200 mm
LIGHT GAUGING
25 mm Rod
Lateral Distance
100 x 100 mm
Lateral Distance
100 mm 0 100 mm 200 mm 300 mm 400 mm
100 mm 0 100 mm 200 mm 300 mm
ULTRASONIC QT50U S18U QS18U T30U/T30UX M25U T18U Q45U
400 mm
800 mm
1200 mm
1600 mm
2000 mm
400 mm
Target Distance
400 mm
800 mm
1200 mm
1600 mm
2000 mm
Q45UR MEASURING ARRAYS RADAR
Target Distance
EBPC-9
EBPC-10
T30U Teflon-Encapsulated (Typical)
200 mm 150 mm 100 mm 25 mm Rod
Lateral Distance
50 mm 0 50 mm 100 mm 150 mm 200 mm
100 mm Plate
300 mm
600 mm
900 mm
1200 mm
1500 mm
Target Distance
EBPC-11
327
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
U-GAGE M25U
SENSORS
ACCESSORIES
Stainless Steel Opposed-Mode Ultrasonic Sensors

Features smooth 316 series stainless steel construction to withstand the toughest sanitary challenges Cleans easily with no thread, gaps or seams to trap debris Constructed of FDA approved materials Disinfects and cleans up with minimal effort Offers user-selectable dual range, depending on response time Rated IP69K, IEC IP67 (NEMA 6) with fully encapsulated electronics Provides a wide standard operating temperature range of -20 to +70C Withstands high-temperature sprays of up to 80 C and 1500 psi occurring every few hours Features high immunity to ambient electrical and sonic noise Indicates status using highly visible LEDs protected by a sealed, transparent cover
page 329
103.0 mm
online
25.0 mm
M-GAGE M25U, 10 to 30V dc

Range*
Normal Speed: 500 mm High Speed: 250 mm
Frequency
140 kHz
Connection
4-pin Euro QD 5-pin Euro QD
Output
Bipolar NPN/PNP
Response Time
Normal Speed: 4.0 ms High Speed: 3.0 ms
Models
M25UEQ8 Emitter M25URBQ8 Receiver
Connection options: A model with a QD requires a mating cordset (see page 329). * M25U receivers may be wired for either of two speed modes: Normal or High, depending on hookup. The Normal-Speed mode offers a sensing range of 500 mm. The Normal-Speed mode maximizes sensing energy, as is required in demanding environments. The High-Speed mode offers a sensing range of 250 mm. The High-Speed mode maximizes sensing response, as is needed in high-speed counting applications.
328
U-GAGE M25U Specifications

Sensing Range Normal Speed: 500 mm High Speed: 250 mm 140KHz Emitter: 10 to 30V dc (10% max. ripple) at less than 85 mA Receiver: 10 to 30V dc (10% max. ripple) at less than 38 mA (exclusive of load) Protected against reverse polarity and transient voltages Bipolar (1 NPN & 1 PNP) solid-state output; Normally Closed (output is activated when an object blocks the sensing beam) 100 mA (each output) with short circuit protection; see Note 1 OFF-state leakage current: NPN: < 200 A sinking PNP: < 10 A sourcing ON-state saturation voltage: NPN: < 1.6V @ 100 mA PNP: < 3.0V @ 100 mA Protected against short circuit conditions Normal Speed: 4.0 milliseconds High Speed: 3.0 milliseconds 1 millisecond < 250 milliseconds 20 milliseconds Green Power LED: indicates Power ON Amber Output LED: indicates output activated Housing: 316 Stainless Steel LED window: Polysulfone Emitter: 4-pin Euro-Style QD Receiver: 5-pin Euro-Style QD QD cordsets ordered separately. See page 329. Leakproof design, rated IEC IP67 (NEMA 6), IP69K Temperature: -20 to +70 C Max. Relative Humidity: 95% at 50 C non-condensing All models meet Mil. Std. 202F requirements method 201A (vibration: 10 to 60 Hz max. amplitude 0.06", max. acceleration 10G). Also meets IEC 947-5-2; 30G 11 ms duration.
Supply Voltage and Current Supply Protection Circuitry Receiver Output Configuration Output Rating
Output Protection Circuitry Output Response Time Repeatability Delay at Power-up Delay for Switching Between Normal and High Speed Indicators Construction Connections
Environmental Rating Operating Conditions Vibration and Mechanical Shock Certifications Notes
1. NPN < 200 A for load impedance > 3 K; for load current of 100 mA, leakage < 1% of load current 2. W hen mounting the M25U, care should be taken to acoustically isolate the emitter and receiver to eliminate sound energy coupling between the sensor pair. This is best accomplished with elastomeric materials between the sensor and rigid mounting brackets. Emitter Models: MI21 (p. 763) Receiver Models: MI17 (p. 762)
Hookups Diagrams
Cordsets
Washdown Euro QD
See page 6852 Length
2m 9m
Brackets
See page 687 Length
2m 5m 9m
M25U

MQDCWD-506 MQDCWD-530

MQDEC2-506 MQDEC2-515 MQDEC2-530 MQDEC2-506RA MQDEC2-515RA MQDEC2-530RA pg. 659 SMBM25A pg. 659 SMBM25B
Additional bracket information available. See page 620.
329
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
U-GAGE T18U
SENSORS
ACCESSORIES
Opposed Dual Range Sensors

Offers response time of 2 milliseconds and range of 600 mm for longer-range applications Features ultra-fast response time of 1 millisecond with a range of 300 mm for high-speed applications such as counting Uses high-frequency acoustic emitter and tuned receiver for accurate sensing in bright light and to reliably detect clear materials such as glass Offers high immunity to electrical and acoustic noise Operates at temperature range from -40 to +70 C Includes signal strength indicator to make alignment easy Housed in T-style right-angle sensor package with 18 mm threaded mounting hub, for versatile mounting
page 331
300 mm Range 1 ms Response
600 mm Range 2 ms Response
30.0 mm
51.5 mm 18.0 mm
online
40.0 mm

Range
NORMAL resolution: 600 mm HIGH resolution: 300 mm
Connection
Response Time
NORMAL resolution: 2 ms or HIGH resolution: 1 ms
Models* NPN
Models* PNP
T186UE Emitter T186UEQ Emitter T18VN6UR T18VN6URQ T18VP6UR T18VP6URQ
Connection options: A model with a QD requires a mating cordset (see page 331). For 9 m cable, add suffix W/30 to the 2 m model number (example, T18VN6UR W/30). * Receivers may be wired for either resolutions: Normal or High. Sensor pair requires one emitter and one receiver.
330
U-GAGE T18U Specifications

Sensing Range (no minimum range) Supply Voltage and Current Ultrasonic Frequency Minimum spacing (adjacent pairs) Receiver Output Configuration Receiver Output Rating NORMAL resolution mode: to 600 mm HIGH resolution mode: to 300 mm 12 to 30V dc, 10% max. ac ripple. 50 mA (emitters); 35 mA (receivers), exclusive of output load. 230 kHz 50 mm for emitter-to-receiver separations of up to 150 mm. Add 10 mm of adjacent-pair spacing for every 100 mm of emitter-to-receiver spacing beyond 150 mm. T18VN models: NPN sinking, NO and NC (complementary) T18VP models: PNP sourcing, NO and NC (complementary) 150 mA max. each output at 25 C, derated to 100 mA at 70 C (derate 1 mA per C). Both outputs may be used simultaneously. ON-state saturation voltage: less than 1.5V at 10 mA; less than 2.0 V at 150 mA OFF-state leakage current: less than 1 A at 30V dc Output protection: Overload and short-circuit protected. No false pulse upon receiver power-up: false pulse protection causes a 100 millisecond delay upon power-up. NORMAL resolution mode: 2 milliseconds ON/OFF HIGH resolution mode: 1 millisecond ON/OFF NORMAL resolution mode: 125 Hz max. HIGH resolution mode: 200 Hz max. NORMAL resolution mode: less than 2 mm HIGH resolution mode: less than 1 mm 15 2 Emitters have a green LED for dc power ON. Receivers have two LEDs, one yellow and one green. Green: power ON Yellow: s onic signal received (flash rate is proportional to received signal strength; flash is from full to half intensity). See data sheet for detailed information. T-style yellow PBT polyester housing with black PBT polyester back cover. Transducer housing is threaded M18 x 1. Mating jam nut is supplied for mounting. Acoustic face is epoxy reinforced. Circuitry is epoxy-encapsulated. IEC IP67; NEMA 6P Emitters: 2 m long attached PVC- covered 2-wire cable or 4-pin Euro-style quick-disconnect fitting. Receivers: 2 m long attached PVC-covered 4-wire cable or 4-pin Euro-style quick-disconnect fitting. 9 m long cables are available by request. Mating Euro-style quick-disconnect cordsets are also available. See page 331. -40 to +70 C All models meets Mil.Std 202F requirements method 201A (Vibration: frequency 10 to 60 Hz, max., and double amplitude 0.06", maximum acceleration 10G) and method 213B conditions H&I (Shock: 75G with unit operation; 100G for non-operation). Also meets IEC 947-5-2 requirements: 30G, 11 milliseconds duration, half sine wave.
Output Response Time Rep Rate Mechanical Sensing Repeatability at 300 mm range Beam Angle (-3dB full angle) Indicators
Construction Environmental Rating Connections
Operating Temperature Vibration and Mechanical Shock Certifications Hookup Diagrams
Emitter Models: MI21 (p. 763)
NPN Models: MI19 (p. 762)
PNP Models: MI20 (p. 762)
Cordsets
Euro QD
See page 682 Length
2m 5m 9m
Brackets
T18U

MQDC-406 MQDC-415 MQDC-430 MQDC-406RA MQDC-415RA MQDC-430RA pg. 637 SMB18A pg. 637 SMB18155F pg. 638 SMB18FA..
331
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
U-GAGE Q45U
SENSORS
ACCESSORIES
Flexible Ultrasonic Sensors

Push-button TEACH programming makes it easy to set the near/far limits of the sensing window. Available ranges are 100 to 1400 mm for the short-range models and 0.25 to 3.0 m for the long-range models. Bipolar discrete models have switches for ON/OFF presence detection and HIGH/LOW level control. - In ON/OFF mode, detects either when the target is within the set range or when it is outside the range. - In HIGH/LOW mode, detects when the target is outside the configured range, for fill level control, web tensioning control and similar applications. Response time is programmed with switches in discrete models and with a potentiometer in analog models. For remote programming, analog models can be wired directly to an external switch, controller or computer to set window limitsideal for inaccessible applications such as roll diameter detection for overhead cranes.
page 335
44.5 mm 60.5 mm Program storage cards After you set up window limits, you can store the limits on circuit cards with non-volatile memory for fast setup. Just store the settings from any Q45U sensor on the Q45UML card, and then transfer the settings to any Q45U sensor with the same available sensing range.
87.6 mm
79.4 mm 44.5 mm
online
30.0 mm
87.6 mm
Short-range Models
Long-range Models
U-GAGE Q45U Discrete Output, 12-24V dc

Range Temperature Compensation
No 100 mm - 1.4 m Yes
Connection
2m 5-pin Mini QD 5-pin Euro QD 2m 5-pin Mini QD 5-pin Euro QD
Output Type
Response Time
Models
Q45UBB63DA Q45UBB63DAQ
Bipolar NPN/PNP
Programmable for 20, 40, 160 or 640 ms
Q45UBB63DAQ6 Q45UBB63DAC Q45UBB63DACQ Q45UBB63DACQ6

More on next page
Connection options: A model with a QD requires a mating cordset (see page 335). For 9 m cable, add suffix W/30 to the 2 m model number (example, Q45UBB63DA W/30).
332
U-GAGE Q45U Discrete Output, 12-24V dc (contd)

Range
250 mm - 3 m
Temperature Compensation
Yes
Connection
2m 5-pin Mini QD 5-pin Euro QD
Output Type
Bipolar NPN/PNP
Response Time
Programmable for 40, 80, 320 or 1280 ms
Models
Q45UBB63BC Q45UBB63BCQ Q45UBB63BCQ6
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors Measurement & Inspection Sensors Vision Wireless Lighting & Indicators Safety Light Screens Safety Laser Scanners
U-GAGE Q45U Analog Output, 15-24V dc

Range
100 mm - 1.4 m
Fiber Optic Safety Systems
Temperature Compensation
Yes
Connection *
Output Type
Response Time
Adjustable from 40 to 1280 ms
Safety Controllers & Modules
Models
Q45ULIU64ACR Q45ULIU64ACRQ Q45ULIU64ACRQ6 Q45ULIU64BCR
ACCESSORIES
Selectable 0 to 10V dc or 4 to 20 mA
250 mm - 3 m
Yes
Adjustable from 80 to 2560 ms
Q45ULIU64BCRQ Q45ULIU64BCRQ6
page 335
Connection options: A model with a QD requires a mating cordset (see page 335). For 9 m cable, add suffix W/30 to the 2 m model number (example, Q45UBB63DA W/30).
The far limit may be extended as far as 3.9 m for good acoustical targetshard surfaces with area greater than 100 cm2.
U-GAGE Q45U Specifications

Sensing Range Short Range: Near limit: 100 mm min. Short Range: Far limit: 1.4 m max. Long Range: Near limit: 250 mm min. Long Range: Far limit: 3.0 m max.
NOTE: The far limit may be extended on long range units, as far as 3.9 m for good acoustical targets (hard surfaces with area greater than 100 cm2) Supply Voltage and Current Ultrasonic Frequency Supply Protection Circuitry Output Protection Circuitry Output Configuration Discrete: 12 to 24V dc (10% max. ripple); 100 mA (exclusive of load) Analog: 15 to 24V dc (10% max. ripple); 100 mA (exclusive of load) Long Range: 128 kHz Short Range: 230 kHz
Protected against reverse polarity and transient voltages. Protected against false pulse on power-up and continuous overload or short-circuit of outputs. Discrete: Bipolar: One current sourcing (PNP) and one current sinking (NPN) open-collector transistor. Analog: One voltage sourcing and one current sourcing; one or the other output is enabled by internal programming switch #2. Discrete: 150 mA max. (each) OFF-state leakage current: less than 25 A at 24V dc ON-state saturation voltage: less than 1.5V at 10 mA; less than 2.0V at 150 mA Analog: Voltage sourcing: 0 to 10V dc, 10 mA max. Current sourcing: 4 to 20 mA, 1 to 500 impedance
Output Ratings
More on next page
333
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
U-GAGE Q45U Specifications (contd)

Performance Specifications Short Range Analog resolution or discrete repeatability: 0.1% of sensing distance ( 0.25 mm min.) Analog Linearity: 1% of full scale Temperature effect: 0.05% of sensing distance/ C with temp. comp. 0.2% of sensing distance/ C without temp. comp. Min. window size: 10 mm Hysteresis (discrete output): 5 mm See EBPC-1 to EBPC-4 on page 335. The following may be selected by a 4-position DIP switch. Discrete: Switch 1: Output normally open/normally closed (pump in/pump out) Switch 2: High/Low level control mode or on/off presence sensing mode Switch 3 & 4: Response speed selection (digital filter) Analog: Switch 1: Output slope positive or output slope negative Switch 2: Current output mode or voltage output mode Switch 3: Loss of echo min/max mode or loss of echo Hold Mode Switch 4: Loss of echo min/max default output value Discrete: Three status LEDs: Green: power ON Yellow: o utputs are conducting (Yellow LED also indicates programming status during setup mode) Red: indicates relative strength of received echo Analog: Three status LEDs: Green: power ON Yellow: t arget is sensed within the window limits (Yellow LED also indicates programming status during setup mode) Red flashing: indicates relative strength of received echo 5-segment moving dot LED indicates the position of the target within the sensing window. See data sheet for detailed information. Construction Environmental Rating Connections Operating Conditions Vibration and Mechanical Shock Molded PBT polyester thermoplastic polyester housing, o-ring sealed transparent acrylic top cover, and stainless steel hardware. Q45U sensors are designed to withstand 1200 psi washdown. The base of cabled models has a "-14NPS internal conduit thread. Leakproof design is rated IEC IP67; NEMA 6P 2 m or 9 m attached cable, or 5-pin Mini-style or 5-pin Euro-style QD fitting. QD cordsets are ordered separately. See pages 335. Temperature: -25 to +70 C Relative humidity: 100% Long Range 0.1% of sensing distance ( 0.5 mm min.) 1% of full scale 0.05% of sensing distance/ C 25 mm 10 mm
SENSORS
Effective Beam Adjustments
Indicators
All models meet Mil. Std. 202F requirements. Method 201A (Vibration: 10 to 60Hz max., double amplitude 0.06", maximum acceleration 10G). Method 213B conditions H & I (Shock: 75G with unit operating; 100G for non-operation). Also meets IEC 947-5-2 requirements: 30G, 11 milliseconds duration, half sine wave. Short Range: Min. target size: 10 x 10 mm aluminum plate at 500 mm 35 x 35 mm aluminum plate at 1.4 m Long Range: Min. target size: 50 x 50 mm aluminum plate at 3 m Discrete: Enable/Disable; Connect yellow wire to +5 to 24V dc to enable sensor and 0 to +2V dc to disable sensor. When the sensor is disabled, the last output state is held until the sensor is re-enabled. The wire must be held to the appropriate voltage for at least 40 milliseconds for the sensor to enable or disable.
Application Notes
Certifications
Hookup Diagrams
MI18 (p. 762)
334
Cordsets
See page 687 Length
2m 5m 9m
Brackets
See page 701 Length
2m 4m 10 m
Q45U


MBCC2-506 MBCC2-512 MBCC2-530 pg. 639 SMB30A pg. 640 SMB30MM pg. 641 SMB30SC

Q45U Short Range with Rod Target (Typical) Q45U Short Range with Plate Target (Typical)
150 mm
150 mm
LIGHT GAUGING
100 x 100 mm Plate 10 x 10 mm Plate
Lateral Distance
100 mm 50 mm 0 50 mm 100 mm 150 mm 0
25 mm Rod 10 mm Rod
Lateral Distance
100 mm 50 mm 0 50 mm 100 mm 150 mm 0
ULTRASONIC QT50U S18U QS18U T30U/T30UX M25U
200 mm
400 mm
600 mm
800 mm
1000 mm
1200 mm 1400 mm
200 mm
400 mm
600 mm
800 mm
1000 mm
1200 mm 1400 mm
Sensing Distance
T18U Q45U Q45UR MEASURING ARRAYS RADAR
Sensing Distance
EBPC-1
EBPC-2
Q45U Long Range with 25 mm Rod Target (Typical)
Q45U Long Range with 100 x 100 mm Plate Target (Typical)
400 mm 300 mm
400 mm 300 mm
Lateral Distance
Lateral Distance
200 mm 100 mm 0 100 mm 200 mm 300 mm 400 mm 0 500 mm 1000 mm 1500 mm 2000 mm 2500 mm 3000 mm 3500 mm 4000 mm
200 mm 100 mm 0 100 mm 200 mm 300 mm 400 mm 0 500 mm 1000 mm 1500 mm 2000 mm 2500 mm 3000 mm 3500 mm 4000 mm
Sensing Distance
Sensing Distance
EBPC-3
EBPC-4
335
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
U-GAGE Q45UR
SENSORS
ACCESSORIES
Remote Ultrasonic Sensors

Sensing head choices are 18 mm diameter threaded barrel housing in plastic or stainless steel, or ultra-compact plastic Flat-Pak. Sensing range is 50 to 250 mm. All models feature built-in temperature compensation and an operating temperature range from -25 to +70 C. Analog models feature a selectable positive or negative output slope. Resolution is 0.1 mm for analog models and 0.6 mm for bipolar discrete models. Push-button TEACH-mode programming enables exact programming of sensing ranges and sensing windows. Environmental rating is IEC IP65 and NEMA 4. Digital filtering provides immunity from random electrical and acoustic noise. Response time is programmed with switches in discrete models and with a potentiometer in analog models.
44.5 mm 60.5 mm
18 x 1 mm Thread
page 339
87.6 mm
45.0 mm
M18C2.0 & S18C2.0 Remote Sensors
online
12.0 mm
27.5 mm
30.0 mm Q45UR Controllers (S18C2.0 Remote Sensor separate)
27.5 mm
Q13C2.0 Remote Sensors
U-GAGE Q45UR Discrete Output, 12-24V dc

Sensor Range
50 - 250 mm
Controller Connection
Controller Output
Bipolar NPN/PNP
Kit Models
Q45UR3BA63CK Q45UR3BA63CQK Q45UR3BA63CQ6K Q45UR3BA63CKQ Q45UR3BA63CQKQ Q45UR3BA63CQ6KQ Q45UR3BA63CKS Q45UR3BA63CQKS Q45UR3BA63CQ6KS
Kit Includes Controller Models Sensor Models

Q45UR3BA63C Q45UR3BA63CQ Q45UR3BA63CQ6 Q45UR3BA63C Q45UR3BA63CQ Q45UR3BA63CQ6 Q45UR3BA63C Q45UR3BA63CQ Q45UR3BA63CQ6 M18C2.0 Stainless Steel Barrel Q13C2.0 Flat-Pak S18C2.0 Molded Barrel
50 - 250 mm
5-pin Mini QD 5-pin Euro QD 2m
Bipolar NPN/PNP
50 - 250 mm
Bipolar NPN/PNP
Connection options: A model with a QD requires a mating cordset (see page 339). For 9 m cable, add suffix W/30 to the 2 m model number (example, Q45UR3BA63CK W/30).
336
U-GAGE Q45UR Analog Output, 15-24V dc

Sensor Range
50 - 250 mm
Controller Cable
Controller Output
Kit Models
Q45UR3LIU64CK Q45UR3LIU64CQK Q45UR3LIU64CQ6K
Kit Includes Controller Models Sensor Models

Q45UR3LIU64C Q45UR3LIU64CQ Q45UR3LIU64CQ6 Q45UR3LIU64C Q45UR3LIU64CQ Q45UR3LIU64CQ6 Q45UR3LIU64C Q45UR3LIU64CQ Q45UR3LIU64CQ6 S18C2.0 Molded Barrel Q13C2.0 Flat-Pak M18C2.0 Stainless Steel Barrel
ACCESSORIES
50 - 250 mm
5-pin Mini QD 5-pin Euro QD 2m
Selectable 0 to 10V dc or 4 to 20 mA
Q45UR3LIU64CKQ Q45UR3LIU64CQKQ Q45UR3LIU64CQ6KQ Q45UR3LIU64CKS Q45UR3LIU64CQKS Q45UR3LIU64CQ6KS
50 - 250 mm
Connection options: A model with a QD requires a mating cordset (see page 339). For 9 m cable, add suffix W/30 to the 2 m model number (example, Q45UR3BA63CK W/30).
page 339
U-GAGE Q45UR High-Gain Controllers

Product P/N
63060 63667
Version
Q45UR3BA63CQ6-63060 Q45UR3LIU64CQ6-63667 Discrete Analog
NOTE: Special High-Gain controllers are available for small object detection. Contact factory for more information.
U-GAGE Q45UR Remote Sensors Specifications

Supply Voltage and Current Ultrasonic Frequency Supply Protection Circuitry Output Protection Circuitry Output Rating Discrete: 12 to 24V dc (10% max. ripple); 100 mA (exclusive of load) Analog: 15 to 24V dc (10% max. ripple); 100 mA (exclusive of load) 400 kHz Protected against reverse polarity and transient voltages Both outputs are protected against continuous overload and short circuit Discrete: 150 mA max. (each output) OFF-state leakage current: less than 25 A at 24V dc ON-state saturation voltage: less than 1.5V at 10 mA; less than 2.0V at 150 mA Analog: Voltage sourcing: 0 to 10V dc, 10 mA max. Current sourcing: 4 to 20 mA, 1 to 500 impedance Discrete: Bipolar: One current sourcing (PNP) and one current sinking (NPN) open collector transistor Analog: O ne voltage sourcing and one current sourcing; one or the other output is enabled by internal programming switch #2
More on next page
337
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
U-GAGE Q45UR Remote Sensors Specifications (contd)

Performance Specifications Discrete: Response Speed: 40 or 160 milliseconds (switch selectable) Repeatability*: 0.2% of measured distance Temperature stability: 0.03% of the window limit positions per C from 0 to 50 C, (0.05% per C over remainder of operating temperature range) Sensing window width: 5 to 200 mm, when independent near and far limits are taught; 1, 2, 3, or 4 mm (switch selectable), when a sensing distance set point is taught Hysteresis: 0.5 mm Ultrasonic beam angle: 3.5 Analog: Response Speed: 10 to 320 milliseconds (2 to 64 cycles) selectable Resolution*: 0.2% of sensing distance at 320 milliseconds response, 0.4% of sensing distance at 10 milliseconds response Linearity*: 1% of full scale Temperature stability: 0.03% of sensing distance per C from 0 to 50 C, (0.05% per C over remainder of operating temperature) Ultrasonic beam angle: 3.5 * Repeatability and analog resolution and linearity are specified using a 50 x 50 mm aluminum plate at 22 C under fixed sensing conditions (Analog: using the 4 to 20 mA output @ 15V dc) Effective Beam Adjustments See page 339. Discrete: The following may be selected by a 4-position DIP switch Switch 1: Output normally open (output is energized when target is within sensing window limits), or normally closed (output is energized when target is outside sensing window limits) Switches 2 & 3: Sensing window size (1, 2, 3 or 4 mm) Switch 4: Response speed selection (40 or 160 milliseconds) Analog: Push-button TEACH-mode programming of window limits. The following may be selected by a 4-position DIP switch located on top of the controller, beneath a transparent O-ring sealed acrylic cover and beneath the black inner cover Switch 1: Output slope: output value increases or decreases with distance Switch 2: Output mode: current output or voltage output Switches 3 & 4: Response to loss of echo Response Speed Adjustment: Single-turn potentiometer selects six response values from 10 to 320 milliseconds Indicators Discrete: Three status LEDs: Green: Power ON Yellow: Output are conducting (Yellow also indicates programming status during setup) Red: Relative strength of received echo 5-segment moving dot LED indicates the position of the target within the sensing window Analog: Three status LEDs: Green: Power ON Yellow: Target is sensed within the window limits (Yellow LED also indicates programming status during setup mode) Red: Relative strength of received echo 5-segment moving dot LED indicates the position of the target within the sensing window See data sheet for detailed information Construction Controller: M olded thermoplastic polyester housing, o-ring sealed transparent acrylic top cover, and stainless steel hardware Sensors: M18C2.0: Stainless steel M18 threaded barrel housing and jam nuts, polyetherimide front cover, ceramic transducer, polyurethane rear cover S18C2.0: Thermoplastic polyester S18 threaded barrel housing and jam nuts, polyetherimide front cover, ceramic transducer, polyurethane rear cover Q13C2.0: Molded 30% glass reinforced thermoplastic polyester housing, ceramic transducer, fully epoxy-encapsulated Controller: IEC IP67; NEMA 6P Sensor: IEC IP65; NEMA 4
SENSORS
Environmental Rating Connections Operating Conditions Vibration and Mechanical Shock
Controller: 2 m or 9 m attached cable, or 5-pin Mini-style or Euro-style quick-disconnect fitting. See page 339. Sensor: 2 m attached PVC cable terminated with 4-pin Euro-style quick-disconnect fitting for connection to controller. Controller and sensor: -25 to +70 C Relative humidity: 85% (non-condensing)
All models meet Mil. Std. 202F requirements. Method 201A Vibration: 10 to 60Hz max., double amplitude 0.06" (maximum acceleration 10G). Method 213B conditions H & I (Shock: 75G with unit operating; 100G for non-operation). Also meets IEC 947-5-2 requirements: 30G, 11 milliseconds duration, half sine wave.
More on next page
338
U-GAGE Q45UR Remote Sensors Specifications

Application Notes
(contd)
Discrete: The TEACH-mode function of the controller is used to set the sensing distance set point. The sensing window size is set using DIP switches #2 and #3. The sensing distance set point is centered within the sensing widow. The size of the sensing window may be adjusted at any time, with or without power applied, and without re-teaching the sensing distance set point. The controller has non-volatile memory which remembers the last sensing distance set point setting if power is removed and later reapplied. The sensing distance set point may be programmed using the Remote TEACH input (see hookup diagrams). Acceptable target angle is within 5 of normal for a smooth, flat target; target rotation does affect the apparent target location with respect to the sensor. Analog: T he controller has non-volatile memory which remembers the last sensing distance set point setting if power is removed and later reapplied. The sensing distance set point may be programmed using the Remote TEACH input (see hookup diagrams). Acceptable target angle is within 5 of normal for a smooth, flat target; target rotation does affect the apparent target location with respect to the sensor.
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors Measurement & Inspection Sensors Vision Wireless Lighting & Indicators Safety Light Screens Safety Laser Scanners Fiber Optic Safety Systems
Cordsets
See page 687 Length
2m 5m 9m
Brackets
See page 701 Length
2m 4m 10 m
Q45UR
LIGHT GAUGING ULTRASONIC QT50U S18U QS18U T30U/T30UX


MBCC2-506 MBCC2-512 MBCC2-530 pg. 639 SMB30A pg. 640 SMB30MM pg. 641 SMB30SC
M25U T18U Q45U Q45UR MEASURING ARRAYS RADAR

Q45UR
12.0 mm 10.0 mm 8.0 mm 6.0 mm 4.0 mm
Lateral Distance
2.0 mm 0 -2.0 mm -4.0 mm -6.0 mm -8.0 mm 50 mm x 50 mm Alum. Plate 10 mm Dia. Alum. Rod 0
-10.0 mm -12.0 mm 50 mm 75 mm 100 mm 125 mm 150 mm 175 mm 200 mm 225 mm 250 mm
Target Distance
EBPC-1
NOTE: The pattern displayed for the 50 mm x 50 mm Aluminum plate is referenced to the EDGE of the plate. The pattern displayed for the 10 mm dia. Aluminum rod is referenced to the CENTER of the rod.
339
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
MEASURING ARRAYS
EZ-ARRAY High-Resolution MINI-ARRAY MINI-ARRAY
SENSORS
EZ-ARRAY
page 341
Applications include edge and centerguiding, loop tension control, hole sizing, parts counting and on-the-fly product sizing and profiling. Closely spaced infrared beams detect objects as small as 5 mm wide; edge resolution is 2.5 mm. Controller functionality is built into the receiver, so basic setup requires no controller, software or PC. Easy-to-use software is included for advanced configuration, using a PC. Configuration options include 14 measurement modes, three scanning methods, two analog and two discrete outputs and a serial output. Range is 4 meters. Array heights range from 150 to 2400 mm.
High-Resolution MINI-ARRAY
page 344
MINI-ARRAY
page 348
High-resolution array excels at highspeed, precise process monitoring and inspection applications. Available heights range from 163 to 1951 mm. Closely spaced beams detect objects as small as 2.5 mm. Emitters and receivers can be up to 1.8 m apart. Controllers can be configured for a variety of measurement modes, scan modes and output configurations.
Low-profile light screen pairs are designed for profiling and inspections. Available heights range from 133 to 1819 mm. Depending on the models beam spacing, the array detects objects as small as 19 to 38 mm. Emitters and receivers can be up to 6 m apart or up to 17 m apart, depending on model. Configuration options include blanking, sensitivity and scanning mode. Controllers are available with DeviceNet -compatible output.
DeviceNet is a trademark of Open DeviceNet Vendor Association Inc.
340
A-GAGE EZ-ARRAY
Two-Piece Measuring Light Screens

Applications include edge and center guarding, loop tension control, hole sizing, parts counting and on-the-fly product sizing and profiling. Two-piece design eliminates the needs for a separate controller. Two push buttons are provided for gain method selection and alignment/ blanking. High-excess-gain option for detecting opaque objects and maximizing range in dirty environments. Edge resolution of 2.5 mm on opaque objects in single and double edge scan mode. Low-contrast sensing of semi-transparent materials and objects as small as 5 mm. Seven Zone LEDs provide instant alignment and beam blockage information. Remote TEACH-wire option is included for alignment, blanking, sensitivity, inverted display and DIP switch enabled/disabled. Aluminum housing is compact and rugged for demanding applications.
ACCESSORIES
Provides powerful configuration capabilities Straightforward applications can be configured using six-position DIP switch on front of the receiver. Easy-to-use graphic user interface software is included for advanced configuration using a PC (USB serial adapter requiredsold separately). Integrated 3-digit diagnostic display indicates number of beams blocked, blanking configuration and troubleshooting codes. Bicolor LEDs indicate system and serial communication status. Array lengths range from 150 to 2400 mm. Standard working range is 0.4 to 4 m, with 5 mm beam spacing. Shorter range models with a 0.3 to 1.5 m working range are available.
page 343
LIGHT GAUGING ULTRASONIC MEASURING ARRAYS EZ-ARRAY
L
3-Digit Diagnostic Display
High-Resolution MINI-ARRAY MINI-ARRAY RADAR
Push button/Blanking Bicolor LEDs
Zone Indicators
DIP Switch Configuration
online
EZ-ARRAY Light Screen
W = 36.0 mm D = 45.2 mm
Specialty Application Solutions

Clear Object Detection Carpet Edge Detection
Short-range models with carpet-specific algorithm automatically detect both the carpet tufting and backing edges. Kits are available with an emitter, short-range receiver and mounting bracket for ease of installation and alignment. Clear plate glass profiling (Measure width of glass) Clear plastic bottle detection (Detect presence/absence of bottle) Air-to-backing and backing-to-tufting monitoring
Clear object models (0.3 m to 1.5 m) are designed to detect low-contrast, translucent objects in clean industrial environments. Short-range and low-contrast models are available for plate glass, clear film and bottle detection. Contact Banner Engineering at 1-888-373-6767 or visit bannerengineering.com/ezarray for detailed application and ordering information. Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
341
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
A-GAGE EZ-ARRAY, 12-30V dc5 mm Beam Spacing

Housing Length (L)
227 mm
Array Length
150 mm 300 mm 450 mm 600 mm 750 mm 900 mm 1050 mm** 1200 mm** 1500 mm** 1800 mm** 2100 mm** 2400 mm**
Total Beams
30 60 90 120 150 180 210 240 300 360 420 480
Connection
Range*
Analog Output
Current (420 mA) Voltage (010V) Current (420 mA) Voltage (010V) Current (420 mA) Voltage (010V) Current (420 mA) Voltage (010V) Current (420 mA) Voltage (010V) Current (420 mA)
Emitter Model
EA5E150Q EA5E300Q EA5E450Q EA5E600Q EA5E750Q EA5E900Q EA5E1050Q EA5E1200Q EA5E1500Q EA5E1800Q EA5E2100Q EA5E2400Q
Receiver Model NPN Outputs

EA5R150NIXMODQ EA5R150NUXMODQ EA5R300NIXMODQ EA5R300NUXMODQ EA5R450NIXMODQ EA5R450NUXMODQ EA5R600NIXMODQ EA5R600NUXMODQ EA5R750NIXMODQ EA5R750NUXMODQ EA5R900NIXMODQ EA5R900NUXMODQ EA5R1050NIXMODQ EA5R1050NUXMODQ EA5R1200NIXMODQ EA5R1200NUXMODQ EA5R1500NIXMODQ EA5R1500NUXMODQ EA5R1800NIXMODQ EA5R1800NUXMODQ EA5R2100NIXMODQ EA5R2100NUXMODQ EA5R2400NIXMODQ EA5R2400NUXMODQ
Receiver Model PNP Outputs

EA5R150PIXMODQ EA5R150PUXMODQ EA5R300PIXMODQ EA5R300PUXMODQ EA5R450PIXMODQ EA5R450PUXMODQ EA5R600PIXMODQ EA5R600PUXMODQ EA5R750PIXMODQ EA5R750PUXMODQ EA5R900PIXMODQ EA5R900PUXMODQ EA5R1050PIXMODQ EA5R1050PUXMODQ EA5R1200PIXMODQ EA5R1200PUXMODQ EA5R1500PIXMODQ EA5R1500PUXMODQ EA5R1800PIXMODQ EA5R1800PUXMODQ EA5R2100PIXMODQ EA5R2100PUXMODQ EA5R2400PIXMODQ EA5R2400PUXMODQ
SENSORS
379 mm 529 mm 678 mm 828 mm 978 mm 1128 mm 1278 mm
8-pin Euro QD
0.44 m
Voltage (010V) Current (420 mA) Voltage (010V) Current (420 mA) Voltage (010V) Current (420 mA) Voltage (010V) Current (420 mA) Voltage (010V) Current (420 mA) Voltage (010V) Current (420 mA) Voltage (010V)
ACCESSORIES
page 343
1578 mm 1878 mm 2178 mm 2478 mm
QD models: A model with a QD requires a mating cordset (see page 343). * Models with a range of 100 mm to 1.5 m models are available upon request. Contact factory at 1-888-373-6767 for more information. ** Models with array lengths 1050 mm and longer ship with a center bracket and two end-cap brackets.
A-GAGE EZ-ARRAY Specification

Supply Voltage (Limit Values) Supply Power Requirements Emitter/Receiver Range Field of View Beam Spacing Light Source Minimum Object Detection Size Sensor Positional Resolution Teach Input (Receiver Gray Wire) Two Discrete Outputs Emitter: 12 to 30V dc Receiver Analog Current Models: 12 to 30V dc Receiver Analog Voltage Models: 15 to 30V dc Emitter/Receiver Pair (Exclusive of discrete load): Less than 9 watts 400 mm to 4 m Nominally 3 5 mm Infrared LED Straight Scan, Low-Contrast: 5 mm Straight Scan, High-Excess-Gain: 10 mm Straight Scan: 5 mm Double-Edge Scan: 2.5 mm Single-Edge Scan: 2.5 mm Low: 0 to 2 volts High: 6 to 30 volts or open (input impedance 22 k) Solid-State NPN or PNP (current sinking or sourcing) Rating: 100 mA max. each output OFF-State Leakage Current: N PN: less than 200 uA @ 30V dc PNP: less than 10 uA @ 30V dc ON-State Saturation Voltage: N PN: less than 1.6V @ 100 mA PNP: less than 2.0V @ 100 mA Protected against false pulse on power-up and continuous overload or short circuit. Voltage Sourcing: 0 to 10V (maximum current load of 5 mA) Current Sourcing: 4 to 20 mA (maximum resistance load = (Vsupply3)/0.020)
More on next page
Power-up delay: 2 seconds
Two Analog Outputs
342
A-GAGE EZ-ARRAY Specification

Serial Communication Interface
(contd)
EIA-485 Modbus RTU (up to 15 nodes per communication ring) RTU binary format Baud Rate: 9600, 19.2K or 38.4K 8 Data Bits, 1 Stop Bit, and Even, Odd, or 2 Stop Bits and No Parity Scan times depend on scan mode and sensor length. Straight scan times range from 2.8 to 26.5 milliseconds. Emitter: Red Status LED ON SteadyStatus Flashing at 1 hzError Receiver: 7 Zone Indicators RedBlocked channels within zone GreenAll channels clear within zone 3-digit 7-segment indicators for measurement mode/diagnostic information Sensor Status Bicolor Indicator LED RedHardware Error or Marginal Alignment GreenOK Modbus Activity Indicator LED: Yellow Modbus Error Indicator LED: Red 6-position DIP switch: Used to set scanning type, measurement modes, analog slope and discrete output 2 function. Alternate software GUI interface provides additional options; see full manual. Push Buttons Two momentary push buttons for alignment and gain level selection. Serial communication: The receiver uses a PVC-jacketed, 5-conductor 22-gauge quick-disconnect cable, 5.4 mm diameter. QD cordsets are ordered separately. See page 343. Other Sensor connections: 8-conductor quick-disconnect cordsets (one each for emitter and receiver), ordered separately (may not exceed 75 m long), PVC-jacketed cordsets measure 5.8 mm diameter, have shield wire; 22-gauge conductors. QD cordsets are ordered separately. See page 343. Aluminum housing with clear-anodized finish; acrylic lens cover IEC IP65 Temperature: 40 to +70 C Relative humidity: 95% at 50 C (non-condensing)
Scan Time Status Indicators
System Configuration (Receiver Interface) Connections
Construction Environmental Rating Operating Conditions Certification Hookup Diagrams
LIGHT GAUGING ULTRASONIC MEASURING ARRAYS EZ-ARRAY
NPN models: MI23 (p. 763)
PNP models: MI24 (p. 763)
High-Resolution MINI-ARRAY MINI-ARRAY RADAR
Cordsets
See page 689 Length
4.58 m 9.14 m 15.2 m
Communication Cordsets
See page 703 Length
1.83 m 4.57 m 9.14 m

MAQDC-815 MAQDC-830 MAQDC-850 Additional cordset information available. See page 679.

MQDMC-506 MQDMC-515 MQDMC-530 MQDMC-506RA MQDMC-515RA MQDMC-530RA
ENCLOSURES
PAGE 728
STANDS
Brackets
EZ-ARRAY
Serial Adapters
See page 739 Model
USB to RS-485 serial adapter with integral EZA-USB485-01 communication cordset and USB cable for advanced configuration with a PC.
PAGE 722
LENS SHIELDS
pg. 629 EZA-MBK-20
pg. 656 SMBLBCZB
USB to RS-485 serial adapter for advanced configuration with a PC. NOTE: Communication cordset ordered separately.
PAGE 732
INTUSB485-1
343
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
A-GAGE High-Resolution MINI-ARRAY

SENSORS
ACCESSORIES
High-Resolution Inspection and Profiling Light Screen
Excels at high-speed, precise monitoring and inspection applications, including on-the-fly sizing, profiling, precision edge and center guiding, and hole detection Requires a controller, emitter/receiver pair and interconnecting cordsets for a complete system Offers programmable controller with a selection of measurement modes, scan modes and output configurations Provides 120 sensing beams per foot, for reliable detection of objects as small as 2.5 mm Features a 1.8 m range with easy, forgiving alignment Offers programmable blanking, hysteresis and serial communications Includes advanced software for system configuration using a PC Makes status monitoring easy with indicators visible from three sides of emitter/receiver
page 347
Emitters/Receivers
W D
online
High-Resolution MINI-ARRAY Sensors

W = 38.1 mm D = 38.1 mm
A-GAGE High-Resolution MINI-ARRAY Emitters/Receivers2.5 mm Beam Spacing

Housing Length (L)
236 mm
Array Length
163 mm
Total Beams
64
Connection
5-pin Mini QD
Range
0.4 - 1.8 m
Minimum Object Size

2.5 mm
Models*
MAHE6A MAHR6A
More on next page
QD models: A model with a QD requires a mating cordset (see page 347). * E and R in model numbers denotes Emitter and Receiver respectively. Sold separately.
344
A-GAGE High-Resolution MINI-ARRAY Emitters/Receivers2.5 mm Beam Spacing (contd)

Housing Length (L)
399 mm
Array Length
325 mm
Total Beams
128
Connection
Range
Minimum Object Size
Models*
MAHE13A MAHR13A MAHE19A MAHR19A MAHE26A MAHR26A MAHE32A MAHR32A MAHE38A MAHR38A
ACCESSORIES
561 mm
488 mm
192
724 mm
650 mm
256
887 mm
813 mm
320
1049 mm
975 mm
384 5-pin Mini QD
1215 mm
1138 mm
448
0.4 - 1.8 m
2.5 mm
MAHE45A MAHR45A MAHE51A MAHR51A MAHE58A MAHR58A MAHE64A MAHR64A MAHE70A MAHR70A MAHE77A MAHR77A
1377 mm
1300 mm
512
page 347
1540 mm
1463 mm
576
1703 mm
1626 mm
640
LIGHT GAUGING ULTRASONIC MEASURING ARRAYS EZ-ARRAY High-Resolution MINI-ARRAY MINI-ARRAY RADAR
1865 mm
1788 mm
704
2028 mm
1951 mm
768
QD models: A model with a QD requires a mating cordset (see page 347). * E and R in model numbers denotes Emitter and Receiver respectively. Sold separately.
Controllers
106.0 mm 115.0 mm
online
81.0 mm
High-Resolution MINI-ARRAY Controller
A-GAGE High-Resolution MINI-ARRAY Controllers, 16-30V dc

Inputs
1 Sensor pair & Trigger (Gate)
Solid-State Discrete Outputs

2 PNP 2 NPN 2 PNP 2 NPN
Analog Outputs
(2) 0-10V Sourcing (2) 0-10V Sourcing (2) 4-20 mA Sinking (2) 4-20 mA Sinking
Serial Output
RS-232 & RS-485
Controller Models
MAHCVP-1 MAHCVN-1 MAHCIP-1 MAHCIN-1
One controller and an emitter/receiver pair (of matching length) required per system.
345
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
A-GAGE High-Resolution MINI-ARRAY Emitter/Receiver Specifications

Emitter/Receiver Range Minimum Object Sensitivity Sensor Scan Time 380 mm to 1.8 m 2.5 mm 1.8 to 58.4 milliseconds, depending on scanning method and sensor length plus 1 millisecond post processing time for controller. 12V dc 2%, supplied by controller Sensors connect to controller using two 5-conductor quick-disconnect cordset (one each for emitter and receiver), ordered separately. Use only Banner cordset, which incorporate a twisted pair for noise immunity. Cordsets measure 8.1 mm in diameter and are shielded and PVC-jacketed. Conductors are 20 gauge (0.9 mm). Emitter and receiver cordset may not exceed 75 m long, each. See page 347. Emitter: Receiver: Red LED lights to indicate proper emitter operation Green indicates sensors aligned Yellow indicates marginal alignment of one or more beams Red indicates sensors misaligned or one or more beam(s) blocked
SENSORS
Power Requirements Connections
Status Indicators
Construction Environmental Rating Operating Conditions Certifications
Aluminum, with black anodized finish; acrylic lens cover NEMA 4, 13; IP65 Temperature: 0 to +50 C Relative humidity: 95% at 50 C (non-condensing)
A-GAGE High-Resolution MINI-ARRAY Controller Specifications

Power Requirements Inputs 16 to 30V dc @ 1.0 A (typical: 0.5 A @ 16V dc) Sensor input: Emitter and receiver wire in parallel to five terminals. Trigger (Gate) input: Optically isolated, requires 10 to 30V dc (7.5 k impedance) for gate signal Remote alignment input: Optically isolated, requires 10 to 30V dc (7.5 k impedance) for alignment sequence signal NPN outputs: Open collector NPN transistor rated at 30V dc max., 150 mA max. PNP outputs: Open collector PNP transistor rated at 30V dc max., 150 mA max. All discrete outputs: OFF-state leakage current: less than 10 A @ 30V dc ON-state saturation voltage: less than 1V @ 10 mA; less than 1.5V @ 150 mA RS-232 or RS-485 interface. (Up to 15 control modules may be given unique addresses on one RS-485 party line.) ASCII or binary data format 9600, 19.2K or 39.4K baud rate 8 data bits, stop bit, and even, odd or no parity Voltage-sourcing outputs: 0 to 10V dc (25 mA current limit) Current-sinking outputs: 4 to 20 mA (16 to 30V dc input) Resolution: Span / Number of sensing channels Linearity: 0.1% of full scale Temperature variation: 0.01% of full scale per C MAHCVP-1: Two PNP discrete (switched), two 0-10V voltage sourcing MAHCVN-1: Two NPN discrete (switched), two 0-10V voltage sourcing MAHCIP-1: Two PNP discrete (switched), two 4-20 mA current sinking MAHCIN-1: Two NPN discrete (switched), two 4-20 mA current sinking Via RS-232 interface to PC-compatible computer running Windows 95, 98, NT, ME, XP or 2000 and using software supplied with each control module. Output 1 (Red): Lights to indicate Discrete Output #1 is active Alarm (Red): Lights to indicate Discrete Output #2 is active Gate (Red): Lights to indicate Trigger (Gate) is active Align (Green): Lights to indicate emitter and receiver are aligned Diagnostics indicator: (Key on controller side label) Identifies System errors and status Polycarbonate housing; mounts to flat surface or directly onto 35-mm DIN rail NEMA 1; IP20 Temperature: 0 to +50 C Relative humidity: 95% @ 50 C (non-condensing)
Discrete (Switched) Outputs
Serial Data Outputs
Analog Outputs
System Programming Status Indicators
Construction Environmental Rating Operating Conditions Certifications Hookup Diagrams
0-10V sourcing: MI25 (p. 764)
4 to 20 mA voltage: MI26 (p. 764)
346
Cordsets
Mini QD (Shielded with Twisted Pair)
See page 702 Length
4.57 m 7.62 m 15.2 m 22.9 m 30.5 m 38.1 m 45.7 m QDC-515C QDC-525C QDC-550C MAQDC-575C MAQDC-5100C MAQDC-5125C MAQDC-5150C Additional cordset information available. See page 679.
DB9 Communication
See page 704 Length
2.00 m MASC
ENCLOSURES
9-Pin Straight
PAGE 728
STANDS
Lighting & Indicators Safety Light Screens Safety Laser Scanners Fiber Optic Safety Systems Safety Controllers & Modules
PAGE 722
Brackets
High-Resolution MINI-Array
LENS SHIELDS
Safety Two-Hand Control Modules Safety Interlock Switches
PAGE 732
Emergency Stop & Stop Control
pg. 628 DIN-35-..
pg. 633 MSMB-3
347
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
A-GAGE MINI-ARRAY
SENSORS
ACCESSORIES
Inspection and Profiling Light Screens

Features low-profile, programmable measuring light screen systems for inspections and profiling Requires a controller, emitter/receiver pair and interconnecting cordsets for a complete system Offers programmable controller with a selection of measurement modes, scan modes and output configurations Offers emitters/receivers for detecting objects as small as 12.7 mm Available with 9.5 or 19 mm beam spacing Features ranges to 17 m, depending on length and beam spacing Includes advanced software for system configuration using a PC Available in models for central monitoring and control over a DeviceNet control network Features optional heated enclosures for outdoor applications Makes status monitoring easy with indicators visible from three sides of emitter/receiver
page 353
Emitters/Receivers
W D
online
L
MINI-ARRAY Sensors
W = 38.1 mm D = 38.1 mm
A-GAGE MINI-ARRAY Emitters/Receivers19.1 mm Beam Spacing

Housing Length (L)
201 mm 356 mm 505 mm
Array Length
133 mm 286 mm 438 mm
Total Beams
8
Connection
Minimum Object Size

38.1 mm
Range
Models*
BMEL616A BMRL616A
16 24
5-pin Mini QD
Interlaced Mode: 25.4 mm
0.9 - 17 m
BMEL1216A BMRL1216A BMEL1816A BMRL1816A

More on next page
QD models: A model with a QD requires a mating cordset (see page 353). * E and R in model numbers denotes Emitter and Receiver respectively. Sold separately. DeviceNet is a trademark of the Open DeviceNet Vendor Association, Inc.
348

Housing Length (L)
659 mm 810 mm 963 mm 1115 mm 1267 mm 1572 mm 1877 mm
(contd)
Range Models*
BMEL2416A BMRL2416A BMEL3016A 0.9 - 17 m BMRL3016A BMEL3616A BMRL3616A BMEL4216A BMRL4216A BMEL4816A BMRL4816A 0.9 - 14 m BMEL6016A BMRL6016A BMEL7216A BMRL7216A
Array Length
591 mm 743 mm 895 mm 1048 mm 1200 mm 1505 mm 1810 mm
Total Beams
32 40 48 56 64
Connection
Minimum Object Size
ACCESSORIES
38.1 mm 5-pin Mini QD Interlaced Mode: 25.4 mm
38.1 mm 80 96 5-pin Mini QD Interlaced Mode: 25.4 mm
page 353

Housing Length (L)
201 mm 356 mm 505 mm 659 mm 810 mm 963 mm 1115 mm 1267 mm 1572 mm 1877 mm
Total Beams
16 32 48 64 80 96 112 128 160 192
Array Length
143 mm 295 mm 448 mm 600 mm 752 mm 905 mm 1057 mm 1210 mm 1514 mm 1819 mm
Connection
Minimum Object Size
Range
Models*
BMEL632A BMRL632A BMEL1232A BMRL1232A BMEL1832A BMRL1832A BMEL2432A BMRL2432A BMEL3032A BMRL3032A BMEL3632A BMRL3632A BMEL4232A BMRL4232A BMEL4832A BMRL4832A BMEL6032A BMRL6032A BMEL7232A BMRL7232A
0.6 - 6.1 m 19.1 mm 5-pin Mini QD Interlaced Mode: 12.7 mm
0.6 - 4.6 m
QD models: A model with a QD requires a mating cordset (see page 353). * E and R in models numbers denotes Emitter and Receiver respectively. Sold separately.
349
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
Contollers
100.0 mm 110.0 mm
SENSORS
online
75.0 mm
MINI-ARRAY Controller
A-GAGE MINI-ARRAY Controllers, 16-30V dc

Inputs
ACCESSORIES
Solid-State Discrete Outputs

1 Reed & 1 NPN 2 NPN
Analog Outputs
(2) 0-10V Sourcing (2) 4-20 mA Sinking
Serial Output
RS-232 & RS-485
Controller Models
MAC-1 MACN-1 MACP-1
page 353
1 Sensor pair & Trigger (Gate)
2 PNP 1 NPN 1 NPN
RS-232
MACV-1 MACI-1 MAC16N-1 MAC16P-1 MACNXDN-1* MACPXDN-1*
1 Sensor pair & Trigger (Gate) 1 Sensor pair & Trigger (Gate)
*
16 NPN 16 PNP 2 NPN 2 PNP
RS-232
DeviceNet models One controller and an emitter/receiver pair (of matching length and resolution) required per system. DeviceNet is a trademark of the Open DeviceNet Vendor Association, Inc.
A-GAGE MINI-ARRAY Emitter/Receiver Specifications

Emitter/Receiver Range Max range is specified at the point where 3x excess gain remains. Minimum Object Sensitivity 9.5 mm beam spacing Array Length 143 to 1057 mm: 0.6 to 6.1 m Array Length 1210 to 1819 mm: 0.6 to 4.6 m 19.1 mm beam spacing Array Length 133 to 1057 mm: 0.9 to 17 m Array Length 1200 to 1810 mm: 0.9 to 14 m
9.5 mm Beam Spacing 19.1 mm Beam Spacing Straight, Edge Modes: 19.1 mm Straight, Edge Modes: 38.1 mm Interlaced Mode: 12.7 mm* Interlaced Mode: 25.4 mm* With DeviceNet Controller: With DeviceNet Controller: Straight, Edge Modes: 19.1 mm Straight, Edge Modes: 38.1 mm Skip Mode: Multiply the above by the Skip Mode: Multiply the above by the number of skipped beams, plus 1 number of skipped beams, plus 1 Interlaced Mode: 12.7 mm* Interlaced Mode: 25.4 mm* *Assumes sensing is in the middle 1/3 of sensing range.
Sensor Scan Time Power Requirements Maximum current is for a 6' sensor.
55 microseconds per beam, plus 1 millisecond post process time per scan. DeviceNet: Post process time will vary, based on the number of channels interrogated during each scan. 9.5 mm beam spacing 12V dc 2%, supplied by controller Emitter: 0.10 A @ 12V dc Receiver: 0.75 A @ 12V dc 19.1 mm beam spacing 12V dc 2%, supplied by controller Emitter: 0.10 A @ 12V dc Receiver: 0.50 A @ 12V dc
More on next page
350
A-GAGE MINI-ARRAY Emitter/Receiver Specifications

Connections
(contd)
Sensors connect to controller using 5-conductor Mini-style quick-disconnect cordsets (one each for emitter and receiver), ordered separately. Use only Banner cordsets, which incorporate a twisted pair for noise immunity. Cordsets measure 8.1 mm dia. and are shielded and PVC-jacketed. Conductors are 20 gauge. Emitter and receiver cordsets may not exceed 75 m long, each. See page 353. Emitter: Red LED lights to indicate proper emitter operation Receiver: Green indicates sensors aligned (> 3x excess gain) Yellow indicates marginal alignment of one or more beams (1x -3x excess gain) Red indicates sensors misaligned or one or more beam(s) blocked Aluminum, with black anodized finish; acrylic lens cover NEMA 4, 13; IP65
Status Indicators
Construction Environmental Rating Certification Operating Conditions
Temperature: -20 to +70 C
Relative humidity: 95% at 50 C (non-condensing)
A-GAGE MINI-ARRAY Controller with DeviceNet Specifications

DeviceNet Configurations Vendor code: 12 (Banner Corp.) Device type: 110 Product code: 1 (MACNXDN-1) 2 (MACPXDN-1) Connection types supported: Explicit Message, Poll, COS Network address: 0-63 (network configured), default = 63 Baud rate supported: 125K, 250K, 500K (network configured), default = 125K MACPXDN-1: Two PNP discrete (switched) MACNXDN-1: Two NPN discrete (switched) Controller, emitter and receiver: 16 to 30V dc @ 1.2 A max. (typical: 0.5 A @ 16V dc) 11 to 25V dc - supplied by DeviceNet BUS Network Sensor input: Emitter and receiver wire in parallel to five terminals. Trigger (Gate) input: Optically isolated, requires 10 to 30V dc (7.5 k impedance) for gate signal NPN outputs: PNP outputs: All discrete outputs: Open collector NPN transistor rated at 30V dc max., 150 mA max. Open collector PNP transistor rated at 30V dc max., 150 mA max. OFF-state leakage current: less than 10 A @ 30V dc ON-state saturation voltage: less than 1V @ 10 mA; less than 1.5V @ 150 mA
Output Configurations Power Requirements* DeviceNet Power* Inputs Discrete Outputs
System Programming System Status Indicators
Via DeviceNet interface and supplied EDS files. Output (steady red): Output #1 energized. Alarm (flashing red): Output #2 energized. Gate (steady red): Trigger (Gate) input status. Alignment (steady green): Proper emitter/receiver alignment and a clear, unblocked light screen (ON) when green or green/yellow receiver LEDs are ON. Diag 1 (Green), Diag 2 (Red), Diag 3 (Red): Used in combination to display System status Bicolored (Red/Green) LED visible on the control module front panel indicates network status: Steady Green: On-line, connected to master Flashing Green: On-line, address and baud rate OK Steady Red: Critical network fault or duplicate node address detected Flashing Red: Connection timeout OFF: No network power or off-line Polycarbonate housing; mounts to flat surface or directly onto 35-mm DIN rail NEMA 1; IP20 Temperature: -20 to +70 C Relative humidity: 95% @ 50 C (non-condensing)
Network Status Indicator
Construction Environmental Rating Operating Conditions *Application Note Hookup Diagrams
The controller must be powered up before the DeviceNet connection in every power-up situation for proper operation MI30 (p. 765)
DeviceNet is a trademark of the Open DeviceNet Vendor Association, Inc.
351
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
A-GAGE MINI-ARRAY Controller Specifications

Power Requirements Inputs Discrete Outputs 16 to 30V dc @ 1.25 amps max. (see current requirements for sensors); controller alone, (without sensors connected) requires 0.1 amp. Sensor input (5 connections): Emitter and receiver wire in parallel to five terminals Trigger (Gate) input: Optically isolated, requires 10 to 30V dc (7.5K input impedance) for gate signal MAC-1: Output 1 (OUT 1) - Reed relay contact rated 125V ac/dc max., 10 VA max. resistive load (non-inductive). Output 2 (ALARM) - Open collector NPN transistor rated 30V dc max., 150 mA max, short-circuit protected; may be configured as a second data analysis output, a system alarm output, or a scan trigger output for a parallel array OFF-state leakage current: less than 10 A @ 30V dc ON-state saturation voltage: less than 1V @ 10 mA; less than 1.5V @ 150 mA MACN-1: (2) Open collector NPN transistor outputs MACP-1: (2) Open collector PNP transistor outputs; transistor rated 30V dc max. 150 mA max, short circuit protected; may be configured as a second data analysis output, a system alarm output, or a scan trigger output for a parallel array OFF-state leakage current: less than 10 A @ 30V dc ON-state saturation voltage: less than 1V @ 10 mA; less than 1.5 V @ 150 mA MACV-1/MACI-1: Alarm - Open collector NPN transistor rated 30V dc max. 150 mA max, short circuit protected; may be configured as a data analysis output, a system alarm output, or a scan trigger output for a parallel array OFF-state leakage current: less than 10 A @ 30V dc ON-state saturation voltage: less than 1V @ 10 mA; less than 1.5 V @ 150 mA MAC16P-1: Sixteen open collector PNP transistor outputs MAC16N-1: Sixteen open collector NPN transistor outputs 30V dc max, 150 mA max., short circuit protected OFF-state leakage current: less than 10 A ON-state saturation voltage: less than 1V @ 10 mA; less than 1.9V @ 150 mA Serial Data Outputs RS-232, ASCII or binary data format Baud Rate: 9600, 19.2K, or 38.4K, 8 data bits, 1 start bit, 1 stop bit, even parity Clear data may be suppressed Header string may be suppressed in binary format MAC-1: Up to 15 controllers may be given unique address for RS-485 party line MACV-1: 0-10 Volts sourcing adjustable Null and Span (20 mA current limit) MACI-1: 4-20 mA current sinking adjustable Null and Span (16 to 30V input) Resolution: Span/(Number of sensor channels) Linearity: 0.1% of Full Scale Temperature variation: 0.01% of Full Scale/ C All models: Via RS-232 PC-compatible computer running Windows 95, 98, NT, ME, XP or 2000 operating system and using Banner supplied software All models: 5 5 microseconds per beam plus processing time. The processing time is dependent on the scan analysis and the number of active outputs. This timing assumes a straight scan, continuous, and TBB mode MAC-1, MACN-1 & MACP-1: 1 millisecond processing time MACV-1 & MACI-1: 1.5 milliseconds processing time MAC16N-1 & MAC16P-1: 2.3 to 7 milliseconds processing time Outputs are not active for 5 seconds after system power up. Maximum response time for the system is two sensor scan cycles. A scan cycle includes a sensor scan plus any serial data transmission. Serial transmission (if activated) follows every sensor scan. The following status LEDs are located on the top surface of the module: MACV-1 & MACI-1: V OUT (Red) - (also called I OUT) Indicates that the analog outputs are active MAC-1, MACN-1 & MACP-1: OUT 1 (Red) - Indicates that output 1 is energized MAC16N-1 & MAC16P-1: OUT (Red) - Indicates that at least one output is active ALARM (Red) - Indicates that Output 2 is active/MAC16N-1 & MAC16P-1: Indicates output 16 is active GATE (Red) - Indicates voltage is applied to Trigger (Gate) input DIAG1 DIAG2 Condition (Green) (Red) ALIGN (Green) - Indicates sensor aligned (excess gain > 1x) Normal condition on off DIAG1 (Green) - Indicates power is applied to the module* Receiver error on on DIAG2 (Red) - Indicates receiver failure Emitter error on off DIAG3 (Red) - Indicates emitter failure
SENSORS
Analog Outputs
Controller Programming Sensor Scan Time
System Response Time
Status Indicators
DIAG3 (Red) off off on
More on next page
352
A-GAGE MINI-ARRAY Controller Specifications (contd)

Construction Environmental Rating Operating Conditions Certifications
R
Polycarbonate NEMA 1; IP20 Temperature: -20 to +70 C Relative humidity: 95% (non-condensing)
Hookup Diagram
MAC-1: MI27 (p. 764) MACV-1/MACI-1: MI29 (p. 765)
MACN-1/MACP-1: MI28 (p. 765) MAC16N-1/MAC16P-1: MI31 (p. 765)
Cordsets
Mini QD (Shielded with Twisted Pair)
See page 702 Length
4.57 m 7.62 m 15.2 m 22.9 m 30.5 m 38.1 m 45.7 m QDC-515C QDC-525C QDC-550C MAQDC-575C MAQDC-5100C MAQDC-5125C MAQDC-5150C Additional cordset information available. See page 679.
Safety Controllers & Modules
DB9 Communication
See page 704 Length
2.00 m MASC
ENCLOSURES
9-Pin Straight
PAGE 728
STANDS
PAGE 722
Brackets
MINI-ARRAY
LENS SHIELDS
PAGE 732
pg. 628 DIN-35-..
pg. 633 MSMB-3
353
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
R-GAGE QT50R
SENSORS
ACCESSORIES
Radar-Based Adjustable-Field & Retroreflective Sensors

Uses Frequency Modulated Continuous Wave (FMCW) technology for detecting moving or stationary targets. Provides presence, absence or change information for a detected target - Adjustable-field sensors detect objects up to a set distance, ignoring objects and backgrounds beyond the setpoint. - Retro-wave sensors detect objects in front of a retroflective target, ignoring objects behind the retroflective target. Operates at 24 GHz in the Industrial, Scientific and Medical (ISM) telecommunication band; no special licensing required Rated IP67 for harsh environments Withstands extreme temperatures, rain, fog, snow, humidity and strong wind Detects vehicles at distances up to 15 m Includes DIP switches for sensing distance, sensitivity and output configuration Features bright LED indicators for easy status monitoring
page 356
74.1 mm
46.1 mm
50.8 mm 100.2 mm
Presence sensing in a broad range of weather conditions Vehicle detection on roads and near intersections (AF) Boat detection for locks and dams (AF) Proximity detection for large shipyard cranes (AF) Car detection and counting for tollbooths, parking ramps, gated access and drive-thrus (RW/AF) Train, subway and light rail detection for underground tunnels and shipyard logistics (RW/AF) Truck trailer detection at loading docks (RW/AF)
online
R-GAGE QT50R Adjustable Field, 12-30V dc

Sensing Mode/LED Max Range Connection Telecom Approval
US, Canada, Mexico and Brazil Europe (except UK), Australia and New Zealand China UK
QD models: A model with a QD requires a mating cordset (see page 356). QD models: For 5-pin Euro-style QD, add Q to the 2 m model (example, QT50RAFQ-US). Range is dependent on target object. Contact factory at 1-888-373-6767 for additional models.
Output
Bipolar NPN/PNP Selectable NO or NC
Model
QT50RAF-US QT50RAF-EU QT50RAF-CN QT50RAF-UK
More on next page
15 m
ADJUSTABLE-FIELD FIXED-FIELD
2m
354
R-GAGE QT50R Retroflective, 12-30V dc (contd)

Sensing Mode/LED Max Range Connection Telecom Approval
US, Canada, Mexico and Brazil Europe (except UK), Australia and New Zealand China UK
QD models: A model with a QD requires a mating cordset (see page 356). QD models: For 5-pin Euro-style QD, add Q to the 2 m model (example, QT50RAFQ-US-R). Range is dependent on target object. Contact factory at 1-888-373-6767 for additional models.
Output
Bipolar NPN/PNP Selectable NO or NC
Model
QT50RAF-US-R QT50RAF-EU-R QT50RAF-CN-R QT50RAF-UK-R
ACCESSORIES
12 m
RETRO
2m
R-GAGE QT50R Specifications
Range Effective Beam Detectable Objects Operating Principle Operating Frequency Supply Voltage Supply Protection Circuitry Delay at Power-up Output Configuration Output Protection Indicators Sensor will detect a proper object (see below) up to 12 or 15 m, depending on model and target See charts EBPC-1 and EBPC-2 on page 356 Objects containing metal, water or similar high-dielectric material Frequency Modulated Continuous Wave (FMCW) radar 24.00-24.25 GHz, ISM Band (varies slightly by model and national telecom regulations) 12 to 30V dc, less than 100 mA (exclusive of load) Protected against reverse polarity and transient overvoltages Less than 2 seconds Bipolar NPN/PNP outputs, 150 mA; DIP Switch 7 selects NO (default) or NC operation Protected against short circuit conditions Power LED: Green (Power ON) Signal Strength LED: Red, flashes in proportion to signal strength Output LEDs: Yellow (output energized)/Red (configuration) See data sheets for more detailed information DIP-switch 8 selects ON/OFF response time Adjustable-field: DIP-switch-configurable sensitivity, sensing distance and output configuration Retroreflective: DIP-switch-configurable sensitivity and output configuration; remote line TEACH of the retroreflective target Housing: ABS/polycarbonate Lightpipes: Acrylic Access Cap: Polyester -40 to +65 C IP67 2 m, 5-wire, shielded, cordset or 5-pin Euro-style QD. Mating QD cordsets are ordered separately. See page 356.
page 356
LIGHT GAUGING ULTRASONIC MEASURING ARRAYS TEMPERATURE RADAR QT50R
Response Time Adjustments Construction
Operating Temperature Environmental Rating Connections Certifications
and ETSI/EN 300 440 or FCC Part 15, depending on model (consult factory for other certifications) Hookup Diagram MI22 (p. 763)
355
LIGHT GAUGING
ULTRASONIC
MEASURING ARRAYS
RADAR
Cordsets
See page 687 Length
1.83 m
Brackets
QT50R

MQDEC2-506 MQDEC2-515 MQDEC2-530 MQDEC2-506RA MQDEC2-515RA MQDEC2-530RA pg. 639 SMB30A pg. 641 SMB30SC pg. 640 SMB30MM
SENSORS
4.57 m 9.14 m
Weather Deflector Kit

QT50RCK Required if R-GAGE is exposed to rain and snow Prevents buildup of water or ice on sensor face
Radar Target
BRTR-CC20E Large corner-cube reflector in protective plastic enclosure 7x excess gain at 6 m distance

QT50R Adjustable Field (Four different targets at sensitivity level 8)
8m 6m 4m 2m 0 -2 m -4 m -6 m -8 m
RCS 300 m2 - Passenger Train RCS 3 m2 - Car Cutoff at 1m RCS 0.25 m2 - Weak Object
QT50R Adjustable Field (BRTR-CC20E, RCS=50 m2)
15 m 10 m 5m 0 -5 m Sensitivity 1
RCS 50 m2 - Large Truck
8 1 2 4 5
6 7
Sensitivity 8
-10 m -15 m
5m
10 m 15 m 20 m 25 m 30 m Distance
4m
8m Distance
12 m
16 m
EBPC-1
EBPC-2
356
Web Only
The following standard products are still available from Banner. Please go online to bannerengineering.com for full descriptions and technical references.
Photoelectrics Sensors Fiber Optic Sensors Special Purpose Sensors Measurement & Inspection Sensors Vision Wireless Lighting & Indicators Safety Light Screens
MINI-BEAM2 QS12
VS1
VS4
Q08
Q10/Q14
Safety Laser Scanners Fiber Optic Safety Systems Safety Controllers & Modules Safety Two-Hand Control Modules Safety Interlock Switches Emergency Stop & Stop Control
FI22 Expert
D11/D11E
ECONO-BEAM
M12 & S18 Laser Emitters
VALU-BEAM
Q85
Analog OMNI-BEAM
MAXI-BEAM
MULTI-BEAM
MAXI-AMP
MICRO-AMP & Remote Sensors
Bus-compatible Sensors
R55 & R55 Expert
Magnetic Sensors
L-GAGE Q50
T-GAGE M18T
ULTRA-BEAM Sensors
LS
357

04main Measure Insp Sensors

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

04main Measure Insp Sensors

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

04main Measure Insp Sensors

Uploaded by

Copyright:

Available Formats

LIGHT GAUGING

MEASUREMENT & INSPECTION

EZ-ARRAY High-Resolution MIN-ARRAY MINI-ARRAY

More information online at bannerengineering.com

Light Gauging Sensors

Signal Conditioning Circuitry

Object Movement Microprocessor

Output Circuitry Emitter Circuitry E Laser Emitter Programmed Sensing Window

LIGHT GAUGING ULTRASONIC MEASURING ARRAYS RADAR

Surface Reflectivity and Texture

PSD Receiver Element

Programmed Sensing Window

Specular targets (e.g., a mirror) reflect light in only one direction

Total Expected Measurement Error

More information online at bannerengineering.com

Measuring Light Screens

Minimum Object Detection

Maximum Part Speed

Measuring Modes Sensor Response Time

More information online at bannerengineering.com

L-GAGE LIGHT GAUGING SENSORS

LIGHT GAUGING ULTRASONIC MEASURING ARRAYS RADAR

More information online at bannerengineering.com

Laser Distance-Gauging Sensors

CLASS 1 LASER PRODUCT

LT3 Sensing Ranges

Laser light emitted from this aperture

DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT

Retroreflective models with retroreflector: 0.5 - 50 m Meters

Avoid exposure- laser light emitted from this aperture

More information online at bannerengineering.com

L-GAGE LT3, 12-24V dc

Visible Red Laser

2m 8-pin Euro QD 2m 8-pin Euro QD 2m 8-pin Euro QD

2m 8-pin Euro QD 2m 8-pin Euro QD

L-GAGE LT3 Specifications

More on next page

More information online at bannerengineering.com

L-GAGE LT3 Specifications

Resolution/Repeatability Color Sensitivity (typical) Analog Linearity

Discrete Output Hysteresis

Retroreflective Fast: 20 mm Medium: 10 mm Slow: 6 mm Retroreflective: less than 3 mm/ C Retroreflective: 40 mm

Laser Control Indicators

Environmental Rating Connections Operating Conditions Application Notes

More information online at bannerengineering.com

Threaded 8-Pin Straight

Additional brackets and information available. See page 620.

LIGHT GAUGING LT3 LT7 LH

LG ULTRASONIC MEASURING ARRAYS RADAR

6% Black 18% Gray 90% White

Color Sensitivity Curves

More information online at bannerengineering.com

Highly Accurate Time-of-Flight Laser Gauging Sensors

LT7 Sensing Ranges

Retroreflective models with specified reflector: 0.5 - 250 m 250 . . . 10 Meters

More information online at bannerengineering.com

L-GAGE LT7, 18-30V dc

LT7PLVQ RS-422 or SSI

Class 1 Sensing Laser (Class 2 Alignment Laser)

Long-Range Ultrasonic Sensor