Product Specification

AU OPTRONICS CORPORATION B141EW04 V5

( ) Preliminary Specifications ( V ) Final Specifications Module Model Name 14.1 WXGA Color TFT-LCD B141EW04 V5 (Dell P/N: TK033, M08 Inverter Version)

Customer

Date

Approved by

Date

Howard Lee

2007/06/25

Checked & Approved by

Prepared by

Emerson Huang

2007/06/25

Note: This Specification is subject to change without notice.

NBBU Marketing Division / AU Optronics corporation

document version 0.1

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

Contents
1. Handling Precautions .............................................................................................................. 4 2. General Description................................................................................................................. 5 2.1 General Specification ..........................................................................................................................5 2.2 Optical Characteristics ........................................................................................................................6 3. Functional Block Diagram..................................................................................................... 11 4. Absolute Maximum Ratings.................................................................................................. 12 4.1 Absolute Ratings of TFT LCD Module.............................................................................................12 4.2 Absolute Ratings of Backlight Unit ..................................................................................................12 4.3 Absolute Ratings of Environment .....................................................................................................12 5. Electrical characteristics....................................................................................................... 13 5.1 TFT LCD Module..............................................................................................................................13 5.2 Backlight Unit ...................................................................................................................................15 6. Signal Characteristic ............................................................................................................. 17 6.1 Pixel Format Image ...........................................................................................................................17 6.2 The input data format ........................................................................................................................18 6.3 Signal Description/Pin Assignment...................................................................................................19 6.4 Interface Timing ................................................................................................................................21 7. Connector Description .......................................................................................................... 23 7.1 TFT LCD Module..............................................................................................................................23 7.2 Backlight Unit ...................................................................................................................................23 7.3 Signal for Lamp connector ................................................................................................................23 8. Vibration and Shock Test...................................................................................................... 24 8.1 Vibration Test ....................................................................................................................................24 8.2 Shock Test Spec:................................................................................................................................24 9. Reliability................................................................................................................................ 25 10. Mechanical Characteristics................................................................................................. 26 10.1 LCM Outline Dimension.................................................................................................................26 11. Shipping and Package......................................................................................................... 29 11.1 Shipping Label Format ....................................................................................................................29 11.2. Carton package ...............................................................................................................................30 11.3 Shipping package of palletizing ......................................................................................................31 12. Appendix: EDID description ............................................................................................... 32

document version 0.1

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

Record of Revision
Version and Date 0.1 2007/05/16 0.2 2007/06/25 Page All 1 32~35 Old description First Edition for Customer Preliminary spec Final spec EDID 8 steps New Description Remark

document version 0.1

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

1. Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it. 2) Be sure to turn off power supply when inserting or disconnecting from input connector. 3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots. 4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling. 7) Do not open nor modify the Module Assembly. 8) Do not press the reflector sheet at the back of the module to any directions. 9) In case if a Module has to be put back into the packing container slot after once it was taken out from the container, do not press the center of the CCFL Reflector edge. Instead, press at the far ends of the CFL Reflector edge softly. Otherwise the TFT Module may be damaged. 10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface Connector of the TFT Module. 11) After installation of the TFT Module into an enclosure (Notebook PC Bezel, for example), do not twist nor bend the TFT Module even momentary. At designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module may be damaged. 12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow local ordinances or regulations for disposal. 13) Small amount of materials having no flammability grade is used in the LCD module. The LCD module should be supplied by power complied with requirements of Limited Power Source(, IEC60950 or UL1950), or be applied exemption. 14) The LCD module is designed so that the CCFL in it is supplied by Limited Current Circuit(IEC60950 or UL1950). Do not connect the CCFL in Hazardous Voltage Circuit.

document version 0.1

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

2. General Description
B141EW04 V5 is a Color Active Matrix Liquid Crystal Display composed of a TFT LCD panel, a driver circuit, and backlight system. The screen format is intended to support the WXGA (1280(H) x 800(V)) screen and 262k colors (RGB 6-bits data driver). All input signals are LVDS interface compatible. Inverter of backlight is not included. B141EW04 V5 is designed for a display unit of notebook style personal computer and industrial machine.

2.1 General Specification

The following items are characteristics summary on the table at 25 condition:

Items Screen Diagonal Active Area Pixels H x V Pixel Pitch Pixel Arrangement Display Mode White Luminance (ICCFL=6.3mA) Note: ICCFL is lamp current Luminance Uniformity Contrast Ratio Optical Rise Time/Fall Time Nominal Input Voltage VDD Power Consumption Weight (W/O inverter) Physical Size Electrical Interface Surface Treatment Support Color Temperature Range Operating Storage (Non-Operating) RoHS Compliance

Unit [mm] [mm] [mm]

Specifications 357.7 (14.1 W) 303.36(H) x 189.6 (V) 1280x3(RGB) x 800 0.237 R.G.B. Vertical Stripe Normally White 220 Typ. (5 points average) 200 Min. (5 points average)
(Note1)

[cd/m2]

[msec] [Volt] [Watt] [Grams] [mm]

1.2 max. (5 points) 350:1 Typ.,300:1 Min. 16 Typ., 25 Max. +3.3 Typ. 5.8 Typ (W/O Inverter) @6.0mA 410 g Typ., 440g Max. 320 max. (W) x 206 max. (H) x 5.5 max.(T). R/G/B Data, 3 Sync, Signals, Clock (4 pairs LVDS) Hard coating 3H, Anti-glare type, Haze 40% 262K colors ( RGB 6-bit )

[oC] [oC]

0 to +50 -20 to +60 RoHS Compliance

document version 0.1

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

2.2 Optical Characteristics

The optical characteristics are measured under stable conditions at 25 (Room Temperature):

Item White Luminance ICCFL=6.0mA Viewing Angle

Unit [cd/m2] [degree] [degree] [degree] [degree]

Conditions 5 points average Horizontal CR = 10 Vertical CR = 10 5 Points 13 Points (Right) (Left) (Upper) (Lower)

Min. 200 40 40 10 30

Typ. 220 45 45 20 35

Max. 1.2 1.8

Note 1, 4, 5. 9

Luminance Uniformity Luminance Uniformity CR: Contrast Ratio Cross talk Response Time % [msec] [msec] [msec] Color / Chromaticity Coordinates (CIE 1931)

1 2 6 7 8

300 Rising Falling Rising + Falling Red x Red y Green x Green y Blue x Blue y White x White y
0.545 0.305 0.285 0.520 0.125 0.105 0.283 0.299

350 5 11 16
0.575 0.335 0.315 0.550 0.155 0.135 0.313 0.329

1.4 8 17 25
0.605 0.365 0.345 0.580 0.185 0.165 0.343 0.359

Note 1: 5 points position (Display area : 303.7 (H) x 189.8(V)mm)

document version 0.1

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5
W W /4 W /4 W /4 W /4

H /4

1
H /4 H H /4

4
H /4

Note 2: 13 points position

W W /4 10 10 H /4 W /4 W /4 W /4 10

1 4

2 5

H /4 H H /4

9
H /4 10

10 12 13

11

Note 3: The luminance uniformity of 5 and 13 points is defined by dividing the maximum luminance values by the minimum test point luminance

Maximum Brightness of five

W5 =

points points

Minimum Brightness of five

Maximum Brightness of thirteen points

W13 =

Minimum Brightness of thirteen points

document version 0.1

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5 Note 4: Measurement method The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 30 minutes in a stable, windless and dark room. Photo detector

Field=2

50 cm

LCD Panel

TFT-LCD Module

Center of the screen

Note 5 Definition of Average Luminance of White (YL):

Measure the luminance of gray level 63 at 5 pointsYL = [L (1)+ L (2)+ L (3)+ L (4)+ L (5)] / 5 L (x) is corresponding to the luminance of the point X at Figure in Note (1).

Note 6 Definition of contrast ratio: Contrast ratio is calculated with the following formula.

Contrast ratio (CR)=

Brightness on the White state Brightness on the Black state

document version 0.1

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

Note 7 Definition of Cross Talk (CT) CT = | YB YA | / YA 100 (%)

Where YA = Luminance of measured location without gray level 0 pattern (cd/m2) YB = Luminance of measured location with gray level 0 pattern (cd/m2)

Note 8: Definition of response time:

The output signals of BM-7 or equivalent are measured when the input signals are changed from Black to White (falling time) and from White to Black (rising time), respectively. The response time interval between the 10% and 90% of amplitudes. Refer to figure as below.

"White"
100 % 90%

"Black"

"White"

Optical Response
10% 0%

Tr

Tf

document version 0.1

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5 Note 9. Definition of viewing angle Viewing angle is the measurement of contrast ratio 10, at the screen center, over a 180 horizontal and 180 vertical range (off-normal viewing angles). The 180 viewing angle range is broken down as follows; 90 () horizontal left and right and 90 () vertical, high (up) and low (down). The measurement direction is typically perpendicular to the display surface with the screen rotated about its center to develop the desired measurement viewing angle.

document version 0.1

10

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

3. Functional Block Diagram

The following diagram shows the functional block of the 14. 1inches wide Color TFT/LCD Module:

X-Driver
(4 pairs LVDS) RxIN0 RxIN1 RxIN2 RxCLKIN LCD DRIVE CARD LCD Controller

TFT ARRAY/CELL 1280(R/G/B) x 3

DC-DC Converter Ref circuit

Y-Driver
VDD GND

Backlight Unit

Lamp Connector(2pin) JAE FI-XB30SL-HF10 JST BHSR-02VS-1 Mating Type SM02B-BHSS-1-TB

Mating Housing JAE FI-X30SL Mating ContactFI-XC3-1-15000

document version 0.1

11

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

4. Absolute Maximum Ratings

Absolute maximum ratings of the module is as following:

4.1 Absolute Ratings of TFT LCD Module

Item Logic/LCD Drive Voltage Symbol VDD Min -0.3 Max +4.0 Unit [Volt] Conditions Note 1,2

4.2 Absolute Ratings of Backlight Unit

Item CCFL Current Symbol ICFL Min 3.0 Max 6.5 Unit [mA] rms Conditions Note 1,2

4.3 Absolute Ratings of Environment

Item Operating Temperature Operation Humidity Storage Temperature Storage Humidity Note 1: At Ta (25 ) Note 2: Permanent damage to the device may occur if exceed maximum values Note 3: For quality performance, please refer to AUO IIS(Incoming Inspection Standard).
Twb=39 C

Symbol TOP HOP TST HST

Min 0 5 -20 5

Max +50 95 +60 95

Unit [oC] [%RH] [ C] [%RH]

o

Conditions Note 3 Note 3 Note 3 Note 3

Operating Range

Storage Range

document version 0.1

12

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

5. Electrical characteristics 5.1 TFT LCD Module

5.1.1 Power Specification
Input power specifications are as follows;

Symble VDD PDD IDD IRush VDDrp

Parameter Logic/LCD Drive Voltage VDD Power IDD Current Inrush Current Allowable Logic/LCD Drive Ripple Voltage

Min 3.0

Typ 3.3 1.0. 331 810

Max 3.6

Units [Volt] [Watt] [mA] Note 1 Note 1 Note 2

Note

1500 [mA] 100 [mV] p-p

Note 1 : Maximum Measurement ConditionBlack Patterm Note 2Measure Condition

+3.3V D6 D5 D2 D1 R1 47K G Q3 AO6402 F1 S VCC

(LCD Module Input)

C1 1uF/16V

(High to Low) Control Signal

D1 D2 D5 D6 R2 G 1K C3 S Q3 AO6402 VR1 47K 0.01uF/25V

+12.0V SW1 SW MAG-SPST

R2

1K C2 1uF/25V

90%

3.3V

10% 0V 0.5ms

Vin rising time

document version 0.1

13

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

5.1.2 Signal Electrical Characteristics Input signals shall be low or High-impedance state when VDD is off. Signal electrical characteristics are as follows;

Parameter Vth

Condition Differential Input High Threshold (Vcm=+1.2V) Differential Input Low Threshold (Vcm=+1.2V)

Min

Max 100

Unit [mV]

Vtl

-100

[mV]

Vcm

Differential Input Common Mode Voltage

1.125

1.375

[V]

Note: LVDS Differential Voltage

document version 0.1

14

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

5.2 Backlight Unit

Parameter guideline for CCFL Inverter

Parameter White Luminance 5 points average CCFL current(ICCFL) CCFL Frequency(FCCFL) CCFL Ignition Voltage(Vs) CCFL Ignition Voltage(Vs) CCFL discharge time (sec) CCFL Voltage (Reference) (VCCFL) CCFL Power consumption (PCCFL)

Min 200 3.0 50

Typ 220 6.0 55

Max 6.5 60 1560 1370

Units [cd/m2 ] [mA] rms [KHz] [Volt] rms [Volt] rms

Condition (Ta=25) (Ta=25) Note 2 (Ta=25) Note 3,4 (Ta= 0) Note 5 (Ta= 25) Note 5 (Ta= 25) Note 4 (Ta=25) Note 6 (Ta=25) Note 6

1 612 680 4.2 748 [Volt] rms [Watt]

Note 1: Typ are AUO recommended Design Points. *1 All of characteristics listed are measured under the condition using the AUO Test inverter. *2 In case of using an inverter other than listed, it is recommended to check the inverter carefully. Sometimes, interfering noise stripes appear on the screen, and substandard luminance or flicker at low power may happen. *3 In designing an inverter, it is suggested to check safety circuit very carefully. Impedance of CCFL, for instance, becomes more than 1 [M ohm] when CFL is damaged. *4 Generally, CCFL has some amount of delay time after applying kick-off voltage. It is recommended to keep on applying kick-off voltage for 1 [Sec] until discharge. *5 CCFL discharge frequency must be carefully chosen so as not to produce interfering noise stripes on the screen. *6 Reducing CCFL current increases CCFL discharge voltage and generally increases CCFL discharge frequency. So all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter. Note 2: It should be employed the inverter which has Duty Dimming, if ICCFL is less than 4mA.

document version 0.1

15

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5 Note 3: CCFL discharge frequency should be carefully determined to avoid interference between inverter and TFT LCD. Note 4: The frequency range will not affect to lamp life and reliability characteristics. Note 5: CCFL inverter should be able to give out a power that has a generating capacity of over 1,430 voltage. Lamp units need 1,400 voltage minimum for ignition. Note 6: Calculator value for reference (ICCFLVCCFL=PCCFL) Note 7: Requirements for a system inverter design, which is intended to have a better display performance, a better power efficiency and a more reliable lamp, are following. It shall help increase the lamp lifetime and reduce leakage current. a. The asymmetry rate of the inverter waveform should be less than 10%. b. The distortion rate of the waveform should bewithin 2 10%. * Inverter output waveform had better be more similar to ideal sine wave.

document version 0.1

16

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

6. Signal Characteristic 6.1 Pixel Format Image

Following figure shows the relationship of the input signals and LCD pixel format.

0 1st Line

1278 1279 R G B R GB

R GB R GB

800th Line

R GB R GB

R G B R GB

document version 0.1

17

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

6.2 The input data format

Signal Name +R5 +R4 +R3 +R2 +R1 +R0 +G5 +G4 +G3 +G2 +G1 +G0 +B5 +B4 +B3 +B2 +B1 +B0 RxCLKIN

Description Red Data 5 (MSB) Red Data 4 Red Data 3 Red Data 2 Red Data 1 Red Data 0 (LSB) Red-pixel Data Green Data 5 (MSB) Green Data 4 Green Data 3 Green Data 2 Green Data 1 Green Data 0 (LSB) Green-pixel Data Blue Data 5 (MSB) Blue Data 4 Blue Data 3 Blue Data 2 Blue Data 1 Blue Data 0 (LSB) Blue-pixel Data Data Clock

Red-pixel Data Each red pixel's brightness data consists of these 6 bits pixel data.

Green-pixel Data Each green pixel's brightness data consists of these 6 bits pixel data.

Blue-pixel Data Each blue pixel's brightness data consists of these 6 bits pixel data.

The typical frequency is 68.94 MHZ.. The signal is used to strobe the pixel data and DE signals. All pixel data shall be valid at the falling edge when the DE signal is high. DE Display Timing This signal is strobed at the falling edge of RxCLKIN. When the signal is high, the pixel data shall be valid to be displayed. VS Vertical Sync The signal is synchronized to RxCLKIN . HS Horizontal Sync The signal is synchronized to RxCLKIN . Note: Output signals from any system shall be low or High-impedance state when VDD is off.

document version 0.1

18

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

6.3 Signal Description/Pin Assignment

LVDS is a differential signal technology for LCD interface and high speed data transfer device. Pin# 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 Signal Name GND VDD Aging DATAEDID RxIN0+ RxIN1GND RxIN2+ RxCLKINGND NC NC GND NC NC Pin# 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 Signal Name VDD VEDID CLKEDID RxIN0GND RxIN1+ RxIN2GND RxCLKIN+ NC GND NC NC GND NC

document version 0.1

19

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

Note1: Start from right side

Note2: Input signals shall be low or High-impedance state when VDD is off. internal circuit of LVDS inputs are as following. The module uses a 100ohm resistor between positive and negative data lines of each receiver input

Signal Input LVDS Receiver

Pin No. 8 RxIN0R

RxIN0+

11 RxIN1R

12 RxIN1+

14

RxIN2R

15 RxIN2+ 17

RxCLKINR

18 RxCLKIN+

document version 0.1

20

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

6.4 Interface Timing

6.4.1 Timing Characteristics Basically, interface timings should match the 1280x800 /60Hz manufacturing guide line timing.
Parameter Frame Rate Clock frequency Period Vertical Section Active Blanking Period Horizontal Section Active Blanking Symbol 1/ TClock TV TVD TVB TH THD THB 803 800 3 1303 1280 23 Min. Typ. 60 71.1 823 800 23 1440 1280 160 1023 800 223 2047 1280 767 TClock TLine Max. Unit Hz MHz

Note : DE mode only 6.4.2 Timing diagram

TCLOCK

Input Timing Definition ( DE Mode)

DOTCLK

Input Data

Invaild Data

Pixel 1

Pixel 2

Pixel 3

Pixel N-1

Pixel N

Invaild Data

Pixel 1

DE
THB TH THD

DE
TVB TVD TV

document version 0.1

21

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

6.5 Power ON/OFF Sequence VDD power and lamp on/off sequence is as follows. Interface signals are also shown in the chart. Signals from any system shall be Hi-Z state or low level when VDD is off.
T1
90% 10% 90% 10%

Power Supply VDD

T2

T3

T7

T4

LVDS Interface

T5

VALID DATA T6

Backlight On

Power Sequence Timing

Value Parameter T1 T2 T3 T4 T5 T6 T7 Min. 0.5 0 0 400 200 200 0 Typ. Max. 10 50 50 10 Units (ms) (ms) (ms) (ms) (ms) (ms) (ms)

document version 0.1

22

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

7. Connector Description
Physical interface is described as for the connector on module. These connectors are capable of accommodating the following signals and will be following components.

7.1 TFT LCD Module

Connector Name / Designation Manufacturer Type / Part Number Mating Housing/Part Number Mating Contact/Part Number For Signal Connector JAE/Starconn FI-XB30SL-HF10/093M30-00B0RA-G4 F1-X30H / equivalent type F1-XC3-1-15000 / equivalent type

7.2 Backlight Unit

Physical interface is described as for the connector on module. These connectors are capable of accommodating the following signals and will be following components. Connector Name / Designation Manufacturer Type / Part Number Mating Type / Part Number For Lamp Connector JST BHSR-02VS-1 SM02B-BHSS-1-TB

7.3 Signal for Lamp connector

Pin #
1
2

Cable color
Red White

Signal Name
Lamp High Voltage Lamp Low Voltage

document version 0.1

23

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

8. Vibration and Shock Test 8.1 Vibration Test

Test Spec: z z z z Test method: Acceleration: Frequency: Sweep: Non-Operation 1.5G , sine wave 10 - 500Hz Random 0.5 octave/minute in each of three mutually perpendicular axes.

8.2 Shock Test Spec:

Test Spec: z z z z Test method: Acceleration: Active time: Pulse: Non-Operation 240 G , Half sine wave 2 ms Half sine wave

document version 0.1

24

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

9. Reliability
Items Temperature Humidity Bias High Temperature Operation Low Temperature Operation On/Off Test Hot Storage Cold Storage Required Condition 40/90%,300Hr 50/20%,300Hr 0,300Hr 25, ON/10 sec. OFF/10sec., 30,000 cycles 60/20% RH ,300 hours -20/50% RH ,300 hours Note

Thermal Shock Test -20/30 min ,60/30 min 100cycles Hot Start Test 50/1 Hr min. power on/off per 5 minutes, 5 times Cold Start Test Shock Test (Non-Operating) Vibration Test (Non-Operating) ESD 0/1 Hr min. power on/off per 5 minutes, 5 times

240G, 2ms, Half-sine wave Sinusoidal vibration, 1.5G zero-to-peak, 10 to 500 Hz, 0.5 octave/minute in each of three mutually perpendicular axes. Contact : 8KV, operation, class B Air : 15KV, operation, class B
Note 1

Note1: According to EN61000-4-2 , ESD class B: Some performance degradation allowed. No data lost . Self-recoverable. No hardware failures. Note2: CCFL Life time: 12,000 hours minimum under normal module usage. Note3: MTBF (Excluding the CCFL): 30,000 hours with a confidence level 90%

document version 0.1

25

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

10. Mechanical Characteristics 10.1 LCM Outline Dimension

document version 0.1

26

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

document version 0.1

27

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

10.2 Screw Hole Depth and Center Position

Screw hole minimum depth, from side surface =2.5 mm (See drawing) Screw hole center location, from front surface = 3.1 0.1mm (See drawing) Suggestions: Customers Screw maximum length = 2.3 mm (See drawing)
Screw Torque: Maximum2.5 kgf-cm

2.5 Min

document version 0.1

28

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

11. Shipping and Package 11.1 Shipping Label Format

90 mm
B141EW04 B141EW01 V4
0A 1

V5

0AXXG

35 mm
A00
0XU295 0TK033

Inverter combination Inverter maker: Sumida IC: Maxim Inverter maker: Foxconn IC: MPS

Control code 0AXXG

H/W 0A

1AXXG

1A

document version 0.1

29

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

11.2. Carton package

0TK033

0TK033

REV. A00

The outside dimension of carton is 454(L)mm* 388(W)mm* 352(H)mm, carton and cushion weight are 2920g.

document version 0.1

30

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

11.3 Shipping package of palletizing

By air : 6 *4 layers, one pallet put 24 boxes, total 480 pcs module. By sea : 6 *5 layers, one pallet put 30 boxes, total 600 pcs module.

Top cardboard Stretch film

Label

PET band

Corner angle

Bottom cardboard Wooden pallet

document version 0.1

31

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

12. Appendix: EDID description

Byte (hex) 0 1 2 3 4 5 6 7 8 9 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D Field Name and Comments Header Header Header Header Header Header Header Header EISA manufacture code = 3 Character ID EISA manufacture code (Compressed ASCII) Panel Supplier Reserved Product Code Panel Supplier Reserved Product Code LCD module Serial No - Preferred but Optional (0 if not used) LCD module Serial No - Preferred but Optional (0 if not used) LCD module Serial No - Preferred but Optional (0 if not used) LCD module Serial No - Preferred but Optional (0 if not used) Week of manufacture Year of manufacture EDID structure version # = 1 EDID revision # = 3 Video I/P definition = Digital I/P (80h) Max H image size = (Rounded to cm) Max V image size = (Rounded to cm) Display gamma = (gamma 100)-100 = Example: ( 2.2100 ) 100 = 120 Feature support ( no DPMS, Active off, RGB, timing BLK 1) Red/Green Low bit (RxRy/GxGy) Blue/White Low bit (BxBy/WxWy) Red X Red Y Green X Value (hex) 00 FF FF FF FF FF FF 00 06 AF 44 45 00 00 00 00 01 10 01 03 80 1E 13 78 0A 87 F5 94 57 4F Value (binary) 00000000 11111111 11111111 11111111 11111111 11111111 11111111 00000000 00000110 10101111 01000100 01000101 00000000 00000000 00000000 00000000 00000001 00010000 00000001 00000011 10000000 00011110 00010011 01111000 00001010 10000111 11110101 10010100 01010111 01001111
32

Value (DEC) 0 255 255 255 255 255 255 0 6 175 68 69 0 0 0 0 1 16 1 3 128 30 19 120 10 135 245 148 87 79

document version 0.1

Panel Color Coordinates

Display Parameters

Vendor / Product EDID Version

Header

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37

Timing Descripter #1

38 39 3A 3B 3C 3D 3E 3F 40 41

Green Y Blue X Blue Y White X White Y Established timings 1 (00h if not used) Established timings 2 (00h if not used) Manufacturers timings (00h if not used) Standard timing ID1 (01h if not used) Standard timing ID1 (01h if not used) Standard timing ID2 (01h if not used) Standard timing ID2 (01h if not used) Standard timing ID3 (01h if not used) Standard timing ID3 (01h if not used) Standard timing ID4 (01h if not used) Standard timing ID4 (01h if not used) Standard timing ID5 (01h if not used) Standard timing ID5 (01h if not used) Standard timing ID6 (01h if not used) Standard timing ID6 (01h if not used) Standard timing ID7 (01h if not used) Standard timing ID7 (01h if not used) Standard timing ID8 (01h if not used) Standard timing ID8 (01h if not used) Pixel Clock/10,000 (LSB) Pixel Clock/10,000 (MSB) Horizontal Active (lower 8 bits) Horizontal Blanking (Thbp) (lower 8 bits) Horizontal Active/Horizontal blanking (Thbp) (upper4:4 bits) Vertical Active Vertical Blanking (Tvbp) (DE Blanking typ. for DE only panels) Vertical Active : Vertical Blanking (Tvbp) (upper4:4 bits) Horizontal Sync, Offset (Thfp) Horizontal Sync, Pulse Width Vertical Sync, Offset (Tvfp) Sync Width Horizontal Vertical Sync Offset/Width upper 2 bits

8C 27 27 50 54 00 00 00 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 E4 1B 00 A5 50 20 17 30 30 20 36 00

10001100 00100111 00100111 01010000 01010100 00000000 00000000 00000000 00000001 00000001 00000001 00000001 00000001 00000001 00000001 00000001 00000001 00000001 00000001 00000001 00000001 00000001 00000001 00000001 11100100 00011011 00000000 10100101 01010000 00100000 00010111 00110000 00110000 00100000 00110110 00000000
33

140 39 39 80 84 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 228 27 0 165 80 32 23 48 48 32 54 0

document version 0.1

Standard Timing ID

Establis hed Timings

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

42 43 44 45 46

47 48 49 4A 4B Timing Descripter #2 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F 60 61 62

Horizontal Image Size Vertical image Size Horizontal Image Size / Vertical image size Horizontal Border = 0 (Zero for Notebook LCD) Vertical Border = 0 (Zero for Notebook LCD) Non-interlaced, Normal, no stereo, Separate sync, H/V pol Negatives, DE only note: LSB is set to 1 if panel is DE-timing only. H/V can be ignored. Pixel Clock/10,000 (LSB) Pixel Clock/10,000 (MSB) Horizontal Active = xxxx pixels (lower 8 bits) Horizontal Blanking (Thbp) = xxxx pixels (lower 8 bits) Horizontal Active/Horizontal blanking (Thbp) (upper4:4 bits) Vertical Active = xxxx lines Vertical Blanking (Tvbp) = xxxx lines (DE Blanking typ. for DE only panels) Vertical Active : Vertical Blanking (Tvbp) (upper4:4 bits) Horizontal Sync, Offset (Thfp) = xxxx pixels Horizontal Sync, Pulse Width = xxxx pixels Vertical Sync, Offset (Tvfp) = xx lines Sync Width = xx lines Horizontal Vertical Sync Offset/Width upper 2 bits Horizontal Image Size =xxx mm Vertical image Size = xxx mm Horizontal Image Size / Vertical image size Horizontal Border = 0 (Zero for Notebook LCD) Vertical Border = 0 (Zero for Notebook LCD) Module A Revision = Example: 00, 01, 02, 03, etc. Flag Flag Flag Dummy Descriptor Flag Dell P/N 1st Character Dell P/N 2nd Character Dell P/N 3rd Character Dell P/N 4th Character

30 BE 10 00 00

00110000 10111110 00010000 00000000 00000000

48 190 16 0 0

19 E4 1B 00 A5 50 20 17 30 30 20 36 00 30 BE 10 00 00 00 00 00 00 FE 00 58 55 32 39

00011001 11100100 00011011 00000000 10100101 01010000 00100000 00010111 00110000 00110000 00100000 00110110 00000000 00110000 10111110 00010000 00000000 00000000 00000000 00000000 00000000 00000000 11111110 00000000 01011000 01010101 00110010 00111001
34

25 228 27 0 165 80 32 23 48 48 32 54 0 48 190 16 0 0 0 0 0 0 254 0 88 85 50 57

document version 0.1

Timing Descripter #3 Dell specific information

Product Specification
AU OPTRONICS CORPORATION B141EW04 V5

63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D Checksu m 7E 7F

Dell P/N 5th Character LCD Supplier EEDID Revision # Manufacturer P/N Manufacturer P/N Manufacturer P/N Manufacturer P/N Manufacturer P/N Manufacturer P/N Manufacturer P/N (If <13 char, then terminate with ASCII code 0Ah, set remaining char = 20h) Flag Flag Flag Data Type Tag: Flag SMBUS Value SMBUS Value SMBUS Value SMBUS Value SMBUS Value SMBUS Value SMBUS Value SMBUS Value = max nits (Typically = 00h) Number of LVDS receiver chips = 01 or 02 BIST Enable: Yes = 01 No = 00 (If <13 char, then terminate with ASCII code 0Ah, set remaining char = 20h) (If <13 char, then terminate with ASCII code 0Ah, set remaining char = 20h) (If <13 char, then terminate with ASCII code 0Ah, set remaining char = 20h) Extension flag (# of optional 128 EDID extension blocks to follow, Typ = 0) Checksum (The 1-byte sum of all 128 bytes in this EDID block shall = 0)

35 00 42 31 34 31 45 57 34 00 00 00 FE 00 32 47 56 5D 82 A5 D5 FF 01 01 0A 20 20

00110101 00000000 01000010 00110001 00110100 00110001 01000101 01010111 00110100 00000000 00000000 00000000 11111110 00000000 00110010 01000111 01010110 01011101 10000010 10100101 11010101 11111111 00000001 00000001 00001010 00100000 00100000 00000000

53 0 66 49 52 49 69 87 52 0 0 0 254 0 50 71 86 93 130 165 213 255 1 1 10 32 32 0 1

Timing Descripter #4

01

00000001

document version 0.1

35