Scribd Logo
Upload

Welcome to Scribd!

  • 128 views

    Zurn Light Commercial

    Uploaded by

    marcoplumbing
    1. Zurn Light Commercial Grease Interceptors consist of an interceptor rated at a certain gpm and a properly sized flow control fitting that should be installed as close as possible to the fixture being served for easy access and cleaning. 2. The interceptor must be cleaned regularly based on its capacity and the quantity of grease in the wastewater, with a minimum of cleaning when a 2-3 inch layer of grease accumulates, to maintain the rated efficiency. 3. Cleaning involves removing the cover and diffusing baffle to dispose of grease, flushing the interceptor with water, and inspecting and replacing parts like the cover gasket.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    Zurn Light Commercial

    Uploaded by

    marcoplumbing
    128 views2 pages
    1. Zurn Light Commercial Grease Interceptors consist of an interceptor rated at a certain gpm and a properly sized flow control fitting that should be installed as close as possible to the fixture being served for easy access and cleaning. 2. The interceptor must be cleaned regularly based on its capacity and the quantity of grease in the wastewater, with a minimum of cleaning when a 2-3 inch layer of grease accumulates, to maintain the rated efficiency. 3. Cleaning involves removing the cover and diffusing baffle to dispose of grease, flushing the interceptor with water, and inspecting and replacing parts like the cover gasket.

    Original Title

    zurn light commercial

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    1. Zurn Light Commercial Grease Interceptors consist of an interceptor rated at a certain gpm and a properly sized flow control fitting that should be installed as close as possible to the fixture being served for easy access and cleaning. 2. The interceptor must be cleaned regularly based on its capacity and the quantity of grease in the wastewater, with a minimum of cleaning when a 2-3 inch layer of grease accumulates, to maintain the rated efficiency. 3. Cleaning involves removing the cover and diffusing baffle to dispose of grease, flushing the interceptor with water, and inspecting and replacing parts like the cover gasket.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    128 views2 pages

    Zurn Light Commercial

    Uploaded by

    marcoplumbing
    1. Zurn Light Commercial Grease Interceptors consist of an interceptor rated at a certain gpm and a properly sized flow control fitting that should be installed as close as possible to the fixture being served for easy access and cleaning. 2. The interceptor must be cleaned regularly based on its capacity and the quantity of grease in the wastewater, with a minimum of cleaning when a 2-3 inch layer of grease accumulates, to maintain the rated efficiency. 3. Cleaning involves removing the cover and diffusing baffle to dispose of grease, flushing the interceptor with water, and inspecting and replacing parts like the cover gasket.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    i\

    ZABiT z
    t;
    I
    tt
    t{
    r-;;, - --._._
    L={,.
    r_;*1 LIGHT
    :!
    ii I -"l-.Jl --
    COMMERCIAL
    Sr tJl-)
    .

    J
    I
    d

    FLOW CONTROL

    .- C ANOI]T

    OPT ONAI ZURN t GHT


    P TRAP COIV IV IRCIAL
    StR]ES 27OO
    FLOW NTT RC IPTOR
    APPROVTD

    Zurn Light Commercial Series Grease lnterceptors#2700 consist of a interceptor rated at


    (
    td
    )gpm and a properly sized flow controlfitting.

    iJ
    'j,r...
    1. Zurn Light Commercial Grease lnterceptors hub couplings. . ij"'3
    l

    should be installed as close as possible to the 6. Outlet piping should be connected to the : tt
    '. .l,r

    fixture being served. Always installwhere there sanitary drain, and pipe size should be equal
    is easy access for cover removal and cleaning. to or larger than the inlet piping. Outlet pipe
    2. Aflow control must be installed as close as should also be vented so the interceptor is not
    possible to the underside of the fixture. The siphoned.
    floweontrolmusfbe-instatled with the ventor{air-in- 7. Solid waste should ngF€o into an interceptor.
    take)on the downsiream side of the orifice plate. The Food grinderwaste and'.bther solids should
    vent connection is positioned to the top of the flow be captured in ihe sink or by a solids interceptor
    control fitting and piped upward higher than source before reaching the grease interceptor.
    of water, or to building vent system
    3. lt is recommended that a cleanout iee be in-
    stalled before the flow control to access the
    flow control orifice and clear debris.
    4. The cleanout plug should be installed overthe
    outlet of the interceptor.
    5. The interceptor isto be installed using no-

    Form # JS2 i-a3.. or2 Date: 0611 1 104


    c.N No 101275 Rev. E
    W#d{

    ZABfiT
    LIGHT
    COMMERCIAL
    MATIWENATICE

    General Considerations
    To obtain optimum operating efficiency of a properly sized and installed PDI certified grease interceptor,
    a regular schedule of maintenance must be adhered to.

    Cleaning
    All grease interceptors must be cleaned regularly. The frequency of grease removal is dependent upon the
    capacityoftheinterceptorandthequantityofgreaseinwastewater. Checkinterceptordailyuntilagrease
    level of 2" to 3" has been obtained (cleaning level). When the grease removal interval has been determined
    for a specific installation, regularcleaning at that interval is necessary to maintain the rated efficiency of the
    interceptor. Aftertheaccumulatedgreaseandwastematerialhasbeenremoved,theinterceptorshouldbe
    thoroughly checked to make certain the inlet, outlet, and air relief ports are clear of obstructions.

    1. Remove the center 3/8"Allen bolt lift handle assembly.


    2. Remove cover.
    3. Remove diffusing baffle for cleaning. Dispose of grease in properwaste container.
    4. Clean out remaining grease
    5. Run water into interceptor to flush. Clean out "outlet" chamber by removing cleanout plug and
    spraying water down inside.
    6. Place cleaned baffle assembly back into unit.
    7. lnspect cover gasket and replace as needed.
    8. Replace cover and secure the 3i8l'Allen bolt lift handle assembly.

    ZT'RN PLUMBTNG PRODUCTS GROUP


    LIGTTT CAVMffiCIAL OPffiAIIIAN
    2640 South Wark Street
    FaLconer, New York L4733
    Phane: 7-800/906-5060
    Fax: 716/665-1135 lro,.*JS2 ",ee o . Date OGt11lO4

    You might also like