Massachusetts Institute of Technology Department of Electrical Engineering and Computer Science

MASSACHUSETTS INSTITUTE of TECHNOLOGY Department of Electrical Engineering and Computer Science
Problem Set No. 5 Spring Term, 2003 6.637 Optical Signals, Devices and Systems Issued Tues. 3/11/2003 Due Tues. 3/18/2003
Reading recommendation: 6.637 Class Notes, Chapters 1 - 5;
Problem 5.1 - The Hunt for Errors in Chapters 1 - 3 (a) Please list the errors that you have found (including typos) in rst three chapters of the notes. (b) Please identify sections of the notes (chapters 1-3 only) that are not clearly written or that are confusing. For each occurrence, state the source of the problem or the confusion. Chapter 1 - Basic Properties of Electromagnetic Waves Chapter 2 - Coherence and Interference Chapter 3 - Diraction and Propagation It is acceptable (and preferred) that you to turn in a marked up copy of the pages of the notes that have your corrections. Please be sure to put your name on the pages you turn in.
Problem 5.2 - Lithium Niobate Modulators Your goal is to design intensity and phase modulators for a collimated, unpolarized light beam of intensity, Iin , using the electro-optic eect in a given lithium niobate crystal. Lithium niobate is an uniaxial material (nx = ny ) and its electro-optic tensor contains the following non-zero elements: r22 = r12 = r61 r13 = r23 r42 = r51 and r33
The given crystal has transparent electrodes on the faces perpendicular to the c-axis as shown, and its dimensions are Lx , Ly and Lz . Thus, you can apply electric elds along the z -axis only. However, you can propagate the light beam to be modulated along either the x, y or z axes.
(a) First, I would like you to make a phase-only modulator but without the use of polarizers. Draw a diagram to show how you would operate the crystal to achieve this goal. For your chosen operation, what is your expression for (V )? (b) I would like you to design an intensity modulator. Place the crystal between polarizers (not necessarily crossed), and for each of the three propagation directions, derive an expression for Iout (V )/Iin . Be sure to clearly specify your chosen orientation of the polarizers relative to the axes of the crystal (a diagram is required for each case). (c) Suppose that the wavelength of the light to be modulated is = 0.6m, and that Lx = Ly = Lz . Given that nO = 2.286, nE = 2.200 and that r22 = r12 = r61 = 6.8 pm/V (pm=pico meter= 1012 m) r13 = r23 = 9.6pm/V r42 = r51 = 32.6 pm/V r33 = 30.9 pm/V Which of the three cases makes the most ecient intensity light modulation system in terms of intensity change per volt? What is the half wave voltage for this system? How could you signicantly lower the halfwave voltage?
Problem 5.3 - Acousto-optic Modulator Two counter propagating acoustic pulses g (t) and h(t) are launched at t = 0 into a Bragg cell of length L and interaction width W (both transducers have width W ) as shown. The acoustic material has a refractive index n and acoustic velocity va . It is read out with a plane wave of wavelength at the Bragg angle, B , as shown.
A cos(at) g (t)
x
x va
L/2
B
W va h (t) F
xd
z i(t)
L/2 E
in
photodetector
A cos(at)
(a) Write an expression for the Bragg angle in terms of the device and operational parameters. (b) (1) In the period before the two acoustic pulses meet each other, where (xd1 ) in the back focal plane of the lens would you place a photodetector to receive rst-order diracted light owing to both pulses? (2) Write an expression for the detector current [i1 (t)] in terms of the signal and device parameters. (c) (1) In the period during which the acoustic pulses partially or totally overlap, where (xd2 ) in the back focal plane of the lens would you place a second photodetector to sense the occurrence of this overlap. (2) Write an expression for this detector current [i2 (t)] in terms of the signal and device parameters. (d) The transducers are now changed so that the two acoustic signals are each of width W/2 (new transducer width), and the propagation paths of the acoustic signals are side by side (non-overlapping) as shown. Where (xd3 ) in the back focal plane of the lens would you place a new photodetector to intercept the doubly diracted rst-order beams from this new cell? (e) Write an expression [i3 (t)] for the resulting photodetector current. What important mathematical operation is being performed by the system?
A cos(at) g (t)
x
W/2
va
B
va F
xd
z i(t)
photodetector
W/2
in
h (t)
A cos(at)

Massachusetts Institute of Technology Department of Electrical Engineering and Computer Science

Uploaded by

Copyright:

Available Formats

Massachusetts Institute of Technology Department of Electrical Engineering and Computer Science

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Massachusetts Institute of Technology Department of Electrical Engineering and Computer Science

Uploaded by

Copyright:

Available Formats

MASSACHUSETTS INSTITUTE of TECHNOLOGY Department of Electrical Engineering and Computer Science

Reading recommendation: 6.637 Class Notes, Chapters 1 - 5;

You might also like