2001 Durango

WWW.WIREMAGIC.
COM
Dodge Durango 2001
Installation type: Remote start / security / GPS
Wire/Function
12 VOLTS IGNITION IGNITION 2 ACCESSORY ACCESSORY 2 STARTER TACH LOCK UNLOCK DOORPIN TRUNK PIN DRIVER DOOR LATCH FACTORY ARM FACTORY DISARM BRAKESWITCH PARKLIGHTS HAND BRAKE HORN DRIVER WINDOW UP DRIVER WINDOW DOWN PASSENGER WINDOW UP PASSENGER WINDOW DOWN LEFT REAR WINDOW UP LEFT REAR WINDOW DOWN RIGHT REAR WINDOW UP RIGHT REAR WINDOW DOWN HEADLIGHTS REVERSE LIGHTS VSS WIRE KEY SENSE
Colour
Pink/black or Red Dk.blue Green/red (4.7L engine only) Black/orange Green Yellow Black/gray Orange/violet Pink/violet Yellow*** Tan/black Tan/red Lt.green/orange**** Lt.green/orange**** White/tan Black/yellow White/black Black/red Lt.blue White Purple/white Brown/white Dk.blue/white Red/black Gray/black Green/white Lt.green Violet/black White/orange Lt.blue
Location / Descriptio
Ignition harness Ignition harness Ignition harness Ignition harness Ignition harness Ignition harness At coil or PCM*` In driver's kickpanel** In driver's kickpanel** At courtesy light under dashpanel 16 pin connector Below fuseblock In driver's kickpanel In driver's kickpanel In driver's kickpanel At switch above brake pedal At light switch harness At plug on handbrake lever At steering column At main window switch At main window switch At main window switch At main window switch At main window switch At main window switch At main window switch At main window switch At light switch harness In driver's kickpanel Pin-27 on C2 connector at PCM***** Ignition harness
Polarity
+ + + + + + AC REV POL REV POL + + REV POL REV POL REV POL REV POL REV POL REV POL REV POL REV POL + + 8000ppm -
Vehicle note:
PLEASE NOTE: This vehicle is equipped with a SENTRY-KEY IMMOBILIZER system. Please refer to the ALARM diagram before any remote start installation. * On the 5.9L the coil is located on the front of the engine, PCM is located in front of the Washer fluid reservoir. The 4.7L engine has a coil for each cylinder. Use the TAN colored wire at any of the coils and set your remote starter for 1 cylinder. (see exploded views) ** If equipped with keyless entry, these wires will be positive pulse. Models equipped with factory alarm have a single wire to perform all doorlock and security functions. See the DOORLOCK diagram. *** You can also find the doorpin wires on a BLACK plug on the left side of the brake pedal. BLACK/BLUE for the driver's door, TAN/RED for all the other doors and TAN/BLACK for the hatch. The factory alarm disarm LT.GREEN/ORANGE can also be found on the plug.
Note: The information on this sheet is provided to you on an as is basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. Wiremagic.com Corporation and/or any associated or unassociated individual or corporation who furnishes this document and/or software assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in each and every case is the sole responsibility of the installer performing the work and Wiremagic.com Corporation and/or any associated or unassociated individual or corporation assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly, or in any other way. The information supplied is a guide only. Copyright 1998-2001 Wiremagic.com Corporation. All rights reserved.
Thursday, January 17, 2002
Page 1 of 2
WWW.WIREMAGIC.COM
Dodge Durango 2001
**** Use a ground pulse through a 1500-ohm resistor to disarm factory security (a second pulse will unlock the doors). A ground pulse through a 620-ohm resistor will arm security and lock the doors. The LT.GREEN/ORANGE is found in a BLACK connector on the left side of the brake pedal. ***** Located on the right front inner fender.
Note: The information on this sheet is provided to you on an as is basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. Wiremagic.com Corporation and/or any associated or unassociated individual or corporation who furnishes this document and/or software assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in each and every case is the sole responsibility of the installer performing the work and Wiremagic.com Corporation and/or any associated or unassociated individual or corporation assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly, or in any other way. The information supplied is a guide only. Copyright 1998-2001 Wiremagic.com Corporation. All rights reserved.
Thursday, January 17, 2002
Page 2 of 2

2001 Durango

Uploaded by

Copyright:

Available Formats

2001 Durango

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

2001 Durango

Uploaded by

Copyright:

Available Formats

WWW.WIREMAGIC.

Thursday, January 17, 2002

Thursday, January 17, 2002

You might also like